IMPRESSA XJ9 Professional Instructions for Use

IMPRESSA XJ9 Professional Instructions for Use
KE
For your safety: read and understand manual before use.
JURA Type 683
Table of contents
Your IMPRESSA XJ9 Professional
IMPORTANT SAFEGUARDS
4
Control elements
8
1 Preparing and using for the first time
10
JURA on the Internet ....................................................................................................................................10
Settings by the JURA service technician...................................................................................................10
Setting up the machine ..............................................................................................................................10
Filling the water tank ....................................................................................................................................11
Filling the bean container ............................................................................................................................11
First-time use ................................................................................................................................................12
Determining the water hardness ..............................................................................................................15
Adjusting the grinder ..................................................................................................................................15
Connecting milk ...........................................................................................................................................16
2 Preparation
17
Ways of preparing a beverage ...................................................................................................................18
Espresso and coffee .....................................................................................................................................18
Preparing two specialty coffees.................................................................................................................19
Latte macchiato, cappuccino .....................................................................................................................19
Warm milk and milk foam.........................................................................................................................20
Ground coffee ..............................................................................................................................................20
Permanently setting the amount of water for the cup size .................................................................21
Hot water ...................................................................................................................................................... 22
3 Daily operation
23
Switching on ................................................................................................................................................ 23
Daily maintenance ...................................................................................................................................... 23
Switching off ................................................................................................................................................24
4 Permanent settings in programming mode
25
Enabling and disabling programming mode.........................................................................................26
Product settings .......................................................................................................................................... 27
Enable or disable one-off settings ...........................................................................................................28
Enabling and disabling product selector view .......................................................................................29
Enabling and disabling products .............................................................................................................30
Maintenance settings .................................................................................................................................30
Setting the water hardness ........................................................................................................................31
Energy-saving mode .................................................................................................................................. 32
Automatic switch-off .................................................................................................................................. 33
Unit for amount of water ........................................................................................................................... 33
Restore factory settings .............................................................................................................................34
Language ...................................................................................................................................................... 35
Background color ........................................................................................................................................ 35
Querying information ................................................................................................................................36
2
Table of contents
5
6
7
8
9
10
11
Maintenance
37
Rinsing the machine ...................................................................................................................................38
Rinsing the cappuccino frother ................................................................................................................38
Cleaning the cappuccino frother ..............................................................................................................39
Dismantling and rinsing the cappuccino frother ..................................................................................40
Inserting and activating the filter.............................................................................................................40
Changing the filter .......................................................................................................................................41
Cleaning the machine ................................................................................................................................42
Descaling the machine ..............................................................................................................................44
Cleaning the bean container .....................................................................................................................46
Descaling the water tank ........................................................................................................................... 47
Display messages
48
Troubleshooting
49
Transport and environmentally friendly disposal
51
Transport / Emptying the system..............................................................................................................51
Disposal..........................................................................................................................................................51
Technical data
52
Index
53
JURA contact details / Legal information
56
Symbol description
Warnings
This is the safety alert symbol. lt is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
DANGER indicates a hazardous situation which, if not avoided, will result in death
J DANGER
or serious injury.
J WARNING WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
J CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation
which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to personal injury.
J
Symbols used
T
E
‘Espresso’
Prompt to take action. This symbol means that you are being prompted to
perform some action.
Information and tips to make it even easier to use your IMPRESSA.
Display message
3
IMPORTANT SAFEGUARDS
IMPORTANT SAFEGUARDS
Follow the basic safety
precautions
When using electrical appliances, basic safety precautions shall
always be followed, to reduce the risk of fire, electric shock, and/or
injury to persons, including the following:
Z Read all instructions.
Z Do not touch hot surfaces. Use handles or knobs.
Z To protect against fire, electric shock and injury to persons, do
not immerse power cord, plugs, or body of machine in water
or other liquid.
Z Close supervision is necessary when any appliance is used by
or near children.
Z Unplug from outlet when not in use and before cleaning.
Allow to cool before putting on or taking off parts, and before
cleaning the appliance.
Z Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to the nearest authorized service
facility for examination, repair or adjustment.
Z The use of an accessory attachment not recommended by the
appliance manufacturer may result in fire, electric shock, or
injury to persons.
Z Do not use outdoors.
Z Do not let the cord hang over the edge of a table or counter,
or touch hot surfaces.
Z Do not place on or near a hot gas or electric burner, or in a
heated oven.
Z To disconnect, turn any control to ‘OFF’ then remove plug
from wall outlet.
Z Do not use appliance for other than intended use.
Z Use extreme caution when dispensing hot steam, hot water
or hot coffee.
Z For household use only.
SAVE THESE INSTRUCTIONS.
Pass them on to any subsequent user.
4
IMPORTANT SAFEGUARDS
Intended use
The appliance is designed and intended for household use only. It
shall only be used for coffee preparation and to heat milk and water,
according to these instructions. Use for any other purpose will be
deemed improper. JURA Elektroapparate AG cannot accept any
responsibility for the consequences of improper use.
People, including children, who
Z do not have the physical, sensory or mental capabilities to use
the appliance safely or
Z are inexperienced or lack knowledge in how to use the appliance safely
must be supervised by a responsible person when using it, or must
be instructed in how to use it correctly.
Special power cord set
instructions
Z
Z
Z
Z
The power cord is provided to reduce the risk resulting from
becoming entangled in or tripping over a long cord.
The cord shall be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children
or tripped over.
This appliance has a 3-pin grounded plug.
Do not modify the plug in any way.
Do NOT use extension cords.
If the user chooses to use an extension cord,
Z the marked electrical rating of the extension cord shall be at
least as great as the electrical rating of the appliance, and
Z if the appliance is of the grounded type, the extension cord
shall be a grounding type 3-wire cord, and
Z the longer cord shall be arranged so that it will not drape over
the counter top or tabletop where it can be pulled on by children or tripped over.
J WARNING
To reduce the risk of fire or electric shock, DO NOT remove any service covers. DO NOT modify the appliance in any way that is not
described in these instructions. NO user serviceable parts included.
Repair MUST be done by authorized personnel only.
In the event of signs of damage, for example if there is a smell of
burning, unplug the machine immediately from outlet and contact
JURA customer service.
5
IMPORTANT SAFEGUARDS
J CAUTION
This appliance is for household use. Any servicing other than cleaning and user maintenance shall be performed by an authorized service representative:
Z Do not immerse base in water or try to disassemble.
Z Do not put the appliance or any individual parts in the dishwasher.
Z Check voltage to be sure that the voltage indicated on the
name plate complies with your voltage (the name plate is
located on the underside of your IMPRESSA).
Z Never use warm or hot water to fill the water container. Use
cold water only.
Z Keep your hands and the cord away from hot parts of the
appliance during operation.
There is a risk of scalds or burns on the spouts and the cappuccino
frother / nozzle.
Z Keep children away.
Z Do not touch any hot parts. Use the handles or knobs provided.
Z Ensure that the cappuccino frother / nozzle is correctly fitted
and clean. If incorrectly fitted or if they become blocked, the
cappuccino frother or its parts might come off.
NOTICE
6
Z
Z
Z
Never clean with scouring powders or hard implements.
Ensure that the ventilation slots are not covered.
Never pull out the drip tray during the brewing process. Only
pull the drip tray when the display instructs you or when the
appliance is ready for use.
IMPORTANT SAFEGUARDS
NEVER DO
(or you will void your
warranty protection):
Z
Z
Z
Z
Z
Z
Z
Never fill instant coffee, chocolate mix etc. into the bean container or ground coffee funnel (filler funnel for ground coffee).
It will damage the functioning of the brewing chamber.
Never fill sugar coated coffee beans into the bean container.
In case of doubt, call your dealer.
Never fill anything other than coffee beans into the bean container (no chocolate, no rice, no nuts, no spices, nothing other
than roasted coffee beans).
Never fill frozen beans into the bean container. If you store
beans in the freezer, let them thaw 3 to 4 hours before filling
them into the bean container.
Never fill anything but fresh, cold and clean water into the
water tank, except when decalcifying.
Never use mineral or carbonated water. You can use tap water,
bottled water, spring water and reverse osmosis water.
Never do anything with the machine which is not described in
these instructions. In case of doubt, call your dealer.
7
Control elements
Control elements
8
1
9
2
10
3
11
4
12
J HOT
J HOT
J HOT
5
13
6
7
1
2
3
4
5
6
7
8
Bean container with aroma preservation
cover
Water tank cover
Water tank
Height-adjustable cappuccino frother
Coffee grounds container
Drip tray
Cup platform
8
9
10
11
12
13
Filler funnel for ground coffee
Storage compartment cover
Grinder adjustment switch
Measuring spoon for ground coffee
Hot-water nozzle
Height- and width-adjustable coffee spout
Control elements
1
2
3
4
5
Top of the machine
1
Q On/Off button
2 g Rotary Switch
3 O P button (programming)
Front
4 Display
5 Buttons (button function depends on
what is shown in the display)
1
3
2
Back of the machine
1
Power switch
2 Power cord
3
Port (under cover)
9
1 Preparing and using for the first time
1 Preparing and using for the first time
JURA on the Internet
Visit us on the Internet.
On the JURA website (www.jura.com) you will find interesting and
up-to-date information on your IMPRESSA and on every aspect of
coffee.
Settings by the JURA
service technician
The following settings can only be made by the JURA service technician:
Setting the filter capacity
U
You can also obtain the following optional accessories for your
IMPRESSA from your JURA service partner:
Coffee grounds disposal function set
Drip drain set
Permanent water connection kit
Payment system and other accessories
U
U
U
U
Setting up the machine
NOTICE
If the machine is not lifted properly, it may be damaged.
T Do not lift the machine by the bean container.
T Only lift the machine by gripping it underneath, in the recesses
on the left and right sides of the machine.
When setting up your IMPRESSA, please note the following:
Place the IMPRESSA on a horizontal surface that is not sensitive to water.
Choose a spot for your IMPRESSA which protects the machine
against overheating. Ensure that the ventilation slots are not
covered.
U
U
10
1 Preparing and using for the first time
Filling the water tank
NOTICE
Daily maintenance of the machine and hygiene when handling milk,
coffee and water are key to a perfect coffee result in the cup every
time. You should therefore change the water daily.
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
T Open the water tank cover.
T Remove the water tank and rinse it with cold water.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Close the water tank cover.
Filling the bean container
The bean container has an aroma preservation cover. This will ensure
that your coffee beans retain their aroma for longer.
NOTICE
Coffee beans which have been treated with additives (e.g. sugar),
ground coffee or freeze-dried coffee will damage the grinder.
T Only use roasted, untreated coffee beans to fill the bean
container.
T Remove the aroma preservation cover.
T Remove any dirt or foreign objects from inside the bean
container.
T Fill the bean container with coffee beans and close the
aroma preservation cover.
11
1 Preparing and using for the first time
First-time use
J WARNING
If the machine is operated with a defective power cord, there is a
danger of potentially fatal electric shock.
T Never use a machine which is damaged.
T Never use a machine which has a defective power cord.
E The water volume is given as standard in ‘oz’. You can change
this setting to ‘ml’ in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Unit for amount of
water’).
When using the machine for the first time, you can choose whether
you want to operate IMPRESSA with or without the CLEARYL Pro
Blue filter cartridge. If the water hardness is 10 °dH or more, we recommend using the filter cartridge. If you do not know the hardness
of your water, you can find this out first (see Chapter 1 ‘Preparing and
using for the first time – Determining the water hardness’).
Precondition: The water tank and bean container have been filled.
T Insert the power plug into a power socket.
3 T Switch on the IMPRESSA using the power switch on the back
of the machine.
Q T Press the On/Off button to switch the IMPRESSA on.
The display shows the languages you can choose from.
E To display more languages, press the ‘Next’ button (bottom
right).
T Press the button that corresponds to the language you want,
e.g. ‘English’.
‘Saved’ appears briefly on the display to confirm the setting.
‘Filter’
E Now decide whether you want to operate your IMPRESSA with
or without a CLEARYL Pro Blue filter cartridge.
12
1 Preparing and using for the first time
Activating the filter
NOTICE
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
T Press the ‘Active’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Insert filter’
T Remove and empty the water tank.
T Open the filter holder and insert the filter cartridge into the
water tank, exerting slight pressure.
T Close the filter holder. It will click into place audibly.
E After two months, the filter will cease to work. Set the date on
the date plate on the filter holder in the water tank.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Place a receptacle under the cappuccino frother, the coffee
spout and the hot-water nozzle.
T Press the ‘Next’ button.
‘Filter is being rinsed.’, water flows out of the hot-water nozzle.
E You can interrupt rinsing of the filter at any time by pressing
any button. Press the Rotary Switch k to continue rinsing of
the filter.
E The water may be slightly discolored. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically.
‘System is filling.’, the system fills up with water. Water flows
out of the cappuccino frother and the hot-water nozzle. The
operation stops automatically.
‘Welcome to JURA’
‘Machine is rinsing.’, the machine rinses. The operation stops
automatically. ‘Please select product:’ appears on the display.
Your IMPRESSA is ready for use.
E The display shows the products you can prepare.
13
1 Preparing and using for the first time
Deactivating the filter
NOTICE
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
T Press the ‘Inactive’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Water hardness’
E If you do not know the hardness of your water, you must find
this out first (see Chapter 1 ‘Preparing and using for the first
time – Determining the water hardness’).
T Press the ‘ < ’ or ‘ > ’ button to set the water hardness.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Welcome to JURA’
‘Please press the Rotary Switch.’
T Place a receptacle under the cappuccino frother and another
under the hot-water nozzle.
k T Press the Rotary Switch.
‘System is filling.’, the system fills up with water. Water flows
out of the cappuccino frother and the hot-water nozzle. The
operation stops automatically.
‘Welcome to JURA’ appears on the display.
‘Machine is heating.’
‘Please press the Rotary Switch.’, the Rotary Switch lights up.
T Place a receptacle under the coffee spout.
k T Press the Rotary Switch.
‘Machine is rinsing.’, the machine rinses. The operation stops
automatically. ‘Please select product:’ appears on the display.
Your IMPRESSA is ready for use.
E The display shows the products you can prepare.
14
1 Preparing and using for the first time
Determining the water
hardness
You can find out what the water hardness is by using the Aquadur®
test strip supplied as standard.
T Hold the test strip briefly (for 1 second) under flowing water.
Shake off the water.
T Wait for about one minute.
T You will then be able to read the degree of water hardness
from the discoloration of the Aquadur® test strip and the
description on the packaging.
You can now adjust the water hardness.
The water hardness can be adjusted on a continuous scale between
1 °dH and 30 °dH.
Level
Display German Degrees of general Parts per
Indicator Strip number
Degree (°dH)
hardness (°dGH)
million (ppm) of ‘reddish’ fields
Not active
–
–
–
–
Very soft water
<3
<3
< 53.4
None
Soft water
>4
>4
> 71
1
Hard water
> 8.4
> 8.4
> 150
2
Very hard water
> 14
> 14
> 250
3
Adjusting the grinder
NOTICE
If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is running.
You can adjust the grinder on a continuous scale to suit the degree
of roast of your coffee.
The consistency of grind is correct if the coffee flows regularly from
the coffee spout. In addition a fine, thick crema forms.
Example: Proceed as follows to change the consistency of grind
during the preparation of an espresso.
T Open the storage compartment cover.
T Place a cup under the coffee spout.
15
1 Preparing and using for the first time
T Press the ‘Espresso’ button.
The grinder starts up. ‘Espresso’ is displayed.
T Turn the grinder adjustment switch to the desired position
while the grinder is running.
The espresso is prepared and the consistency of grind is
adjusted.
T Close the storage compartment cover.
Connecting milk
16
Your IMPRESSA creates fine, creamy, feather-light milk foam with a
perfect consistency. The most important requirement for frothing
milk is a milk temperature of 39–46 °F (4–8 °C). We would therefore
recommend using a milk cooler.
T Attach the milk pipe to the cappuccino frother. To do this,
attach the end of the milk pipe to the connector on the lefthand side of the cappuccino frother.
T Connect the other end of the milk pipe to a milk cooler.
2 Preparation
2 Preparation
J WARNING
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water
and seek medical attention.
T Keep children AWAY.
E You can stop preparation of a specialty coffee, specialty coffee
with milk or hot water at any time. Just press any button.
E During the grinding operation you can select the coffee
strength of individual products by turning the Rotary
Switch g: ; (extra-mild), ;; (mild), ;;; (normal), ;;;; (strong)
or ;;;;; (extra-strong).
E During preparation, you can change the preset amount of
water by turning the Rotary Switch g or pressing the ‘ < ’ and
‘ > ’ buttons.
E You can follow the current status of preparation on the display.
E The water volume is given as standard in ‘oz’. You can change
this setting to ‘ml’ in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Unit for amount of
water’).
In programming mode you can enable or disable one-off settings
during preparation (see Chapter 4 ‘Permanent settings in programming mode – Enable or disable one-off settings’).
You can make permanent settings for all products in programming
mode (see Chapter 4 ‘Permanent settings in programming mode –
Product settings’).
17
2 Preparation
Ways of preparing a
beverage
Only some of the specialty coffees you can prepare are shown on
the display at any one time. As soon as you turn the Rotary Switch,
more specialty coffees are displayed in the product selector. The
product selector disappears automatically after 5 seconds if no
preparation is started.
The following specialty coffees are displayed as standard:
‘Espresso’
‘Coffee’
‘Cappuccino’
‘Latte macchiato’
‘Hot water’
‘1 portion milk’
U
U
U
U
U
U
Additional specialty coffees in the product selector:
‘Ristretto’
‘2 espressi’
‘2 coffees’
‘2 ristretti’
U
U
U
U
Espresso and coffee
‘Espresso’ and ‘Coffee’ are prepared following this model.
Example: Proceed as follows to prepare one coffee.
T Place a cup under the coffee spout.
T Press the ‘Coffee’ button.
Preparation starts. The preset amount of water for coffee
flows into the cup.
Preparation stops automatically. ‘Please select product:’
appears on the display.
18
2 Preparation
Preparing two specialty
coffees
To prepare two specialty coffees, either use the product selector or
press the appropriate preparation button twice (within approximately
2 seconds).
Example: Proceed as follows to prepare two coffees (using product
selector).
T Place two cups under the coffee spout.
g T Turn the Rotary Switch to view the product selector.
g T Turn the Rotary Switch until ‘2 coffees’ is displayed.
k T Press the Rotary Switch.
Coffee preparation starts. The preset amount of water for
coffee flows into the cups.
Preparation stops automatically. ‘Please select product:’
appears on the display.
E Proceed as follows to prepare two cups of coffee at the touch
of a button: Place two cups under the coffee spout. Press the
‘Coffee’ button twice (within approximately 2 seconds) to
start coffee preparation.
Latte macchiato,
cappuccino
Your IMPRESSA can prepare a latte macchiato or cappuccino at the
touch of a button. There is no need to move the glass or cup.
Example: Proceed as follows to prepare one latte macchiato.
Precondition: ‘Please select product:’ is displayed. Milk is connected
to the cappuccino frother.
T Place a glass under the cappuccino frother.
T Turn the setting wheel of the cappuccino frother to the Milk
Foam position ü.
T Press the ‘Latte macchiato’ button.
‘Latte macchiato’, the milk foam is prepared.
Preparation stops automatically when the preset amount of
milk is reached.
E There is a short interval while the hot milk separates from the
milk foam. This allows the typical layers of a latte macchiato
to form. You can choose the length of this interval in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Product settings’).
19
2 Preparation
Coffee preparation starts. The preset amount of water flows
into the glass. Preparation stops automatically. ‘Please select
product:’ appears on the display.
To make sure the cappuccino frother always works properly, you
must rinse and clean it regularly (see Chapter 5 ‘Maintenance – Rinsing the cappuccino frother’).
Warm milk and milk
foam
Example: Proceed as follows to prepare milk foam.
Precondition: ‘Please select product:’ is displayed. Milk is connected
to the cappuccino frother.
T Place a cup under the cappuccino frother.
T Turn the setting wheel of the cappuccino frother to the Milk
Foam position ü.
E If you want to heat the milk turn the setting wheel of the cappuccino frother to the Milk position z.
T Press the ‘1 portion milk’ button.
The machine heats up.
‘1 portion milk’, the milk foam is prepared. Preparation stops
automatically when the preset amount of milk foam is
reached. ‘Please select product:’ appears on the display.
To make sure the cappuccino frother always works properly, rinse
and clean it regularly (see Chapter 5 ‘Maintenance – Rinsing the cappuccino frother’).
Ground coffee
You can choose to use a second coffee variety, for example decaffeinated coffee, with the filter funnel for ground coffee.
E Never add more than two level measuring spoons of ground
coffee.
E Use ground coffee which is not ground too finely. Very fine
coffee can block up the system so that the coffee only comes
out in drips.
E If you did not fill the machine with a sufficient amount of
ground coffee, ‘Not enough ground coffee’ is displayed and
the IMPRESSA stops the operation.
20
2 Preparation
E The desired specialty coffee must be prepared within approximately one minute after filling with the ground coffee. Otherwise the IMPRESSA stops the operation and is once more
ready for use.
All specialty coffees with ground coffee are prepared following this
model.
Example: Proceed as follows to prepare one espresso using ground
coffee.
T Place an espresso cup under the coffee spout.
T Open the cover of the filler funnel for ground coffee.
‘Please add ground coffee.’
T Place one level measuring spoon of ground coffee into the
filler funnel.
T Close the cover of the filler funnel.
‘Please select product:’
T Press the ‘Espresso’ button.
Preparation starts. The preset amount of water for espresso
flows into the cup. Preparation stops automatically. ‘Please
select product:’ appears on the display.
Permanently setting the
amount of water for the
cup size
It is easy to make permanent settings for the amount of water for all
specialty coffees and hot water according to the cup size. Adjust the
amount once as shown in the following example. Every time you
prepare a drink in the future, this amount of water will be dispensed.
The permanent settings for adapting the amount of water to the cup
size for all specialty coffees and hot water follow this model.
Example: Proceed as follows to permanently set the amount of water
for one coffee.
Precondition: ‘Please select product:’ is displayed.
T Place a cup under the coffee spout.
T Press and hold the ‘Coffee’ button.
‘Coffee’ and the fill volume are displayed.
T Hold the ‘Coffee’ button down until ‘Enough water? Press
button’ appears.
T Release the ‘Coffee’ button.
Preparation starts and the coffee flows into the cup.
21
2 Preparation
T Press any button as soon as there is sufficient coffee in the
cup.
Preparation stops. ‘Saved’ appears briefly on the display. The
set amount of water for one coffee is permanently stored.
‘Please select product:’ appears on the display.
E You can alter this setting at any time by repeating the above
procedure.
E You can also permanently set the amount for all specialty coffees, hot water and milk in programming mode (see Chapter 4
‘Permanent settings in programming mode – Product settings’).
Hot water
The following temperatures can be selected for preparing hot water:
‘Low’, ‘Normal’, ‘X high’.
J CAUTION
There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
T Place a cup under the hot-water nozzle.
T Press the ‘Hot water’ button.
‘Hot water’ and the temperature are displayed.
E By pressing the ‘ < ’ or ‘ > ’ button several times (within approximately 2 seconds) you can set the temperature to your individual preference. This setting is not saved.
‘Hot water’, hot water flows into the cup. Preparation stops
automatically. ‘Please select product:’ appears on the display.
22
3
3
Daily operation
Daily operation
Switching on
When the IMPRESSA is switched on, it automatically prompts you
to perform the rinse operation. Start the rinse operation by pressing
the Rotary Switch k. In programming mode you can change this
setting so that the machine starts the switch-on rinse automatically
(see Chapter 4 ‘Permanent settings in programming mode – Maintenance settings’).
Precondition: Your IMPRESSA is switched on at the power switch.
T Place a receptacle under the coffee spout.
Q T Press the On/Off button to switch the IMPRESSA on.
‘Welcome to JURA’ appears on the display. The machine heats
up.
‘Please press the Rotary Switch.’
k T Press the Rotary Switch.
The machine rinses. The operation stops automatically.
‘Please select product:’ appears on the display.
Daily maintenance
To ensure that you get many years of reliable service out of your
IMPRESSA and to guarantee the optimum coffee quality, the machine
requires daily maintenance.
T Pull out the drip tray.
T Empty the coffee grounds container and the drip tray. Rinse
them both with warm water.
T Dry the metal contacts on the back of the drip tray.
T Refit the coffee grounds container and the drip tray.
T Rinse the water tank with clean water.
T Dismantle and rinse the cappuccino frother (see Chapter 5
‘Maintenance – Dismantling and rinsing the cappuccino
frother’).
T Wipe the surface of the machine with a clean, soft, damp
cloth (e.g. microfiber cloth).
23
3
Daily operation
Switching off
When you switch your IMPRESSA off, the spouts used to prepare a
specialty coffee or milk are rinsed.
T Place one receptacle under the coffee spout and another
under the cappuccino frother.
Q T Press the On/Off button.
‘Machine is rinsing.’, ‘Milk system is being rinsed.’. The spouts
used to prepare a specialty coffee or milk are rinsed. The
operation stops automatically. Your IMPRESSA is switched off.
E When the IMPRESSA is switched off with the On/Off button,
the machine consumes less than 0.1 W of standby energy. The
machine can be completely disconnected from the power grid
using the power switch.
24
4
4
Permanent settings in programming mode
Permanent settings in programming mode
J WARNING
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water an
seek medical attention.
T Keep children AWAY.
Press the P button to enter programming mode. You can navigate
through the program items and permanently save the required settings simply by turning the Rotary Switch and using the multi-function buttons. The following settings can be made:
Program item
‘Maintenance status
(1/6)’
‘Product settings (2/6)’
‘Maintenance settings
(3/6)’
Sub-item
‘Clean’
‘Descale’ (only if filter is
not activated)
‘Change the filter’ (only
if filter is activated)
‘Rinse the coffee system’
‘Clean the milk system’
‘Expert mode’
‘product selector’
‘One-off settings’
‘Lock/enable’
‘Filter’
‘Water hardness’ (only if
filter is not activated)
‘Switch-on rinse’
‘Rinse the milk system’
Explanation
T Start the required maintenance program
here.
T Select your settings for specialty coffees
and hot water.
T Deactivate the product selector view.
T Specify whether or not to allow one-off
settings during preparation.
T Enable or disable individual products.
T Indicate whether you are operating your
IMPRESSA with or without a CLEARYL Pro
Blue filter cartridge.
T Adjust the water hardness.
T Change the settings for the switch-on
rinse and milk system rinse.
25
4
Permanent settings in programming mode
Program item
‘Machine settings
(4/6)’
Sub-item
‘Save energy’
‘Switch off after’
‘Units’
‘Factory setting’
‘Machine settings (5/6)’ ‘Choose language’
‘Display’
‘Colour scheme’
‘Information (6/6)’
‘Product counter’
‘Maintenance counter’
‘Day counter’
‘Version’
Enabling and disabling
programming mode
Explanation
T Select an energy-saving mode.
T Set the time after which the IMPRESSA
should switch off automatically.
T Select the unit for the amount of water.
T Reset the permanently set values of all
products to the factory settings.
T Select your language and the background
color for the display.
T Keep track of all specialty coffees prepared
and view the number of maintenance
programs performed.
You can set your IMPRESSA such that programming mode is disabled. When programming mode is disabled, it cannot be accessed
by pressing the P button.
Example: Proceed as follows to disable programming mode.
Precondition: ‘Please select product:’ is displayed.
T Remove the water tank.
‘Fill water tank’
T Press the Rotary Switch, the P button and the bottom righthand button simultaneously for about 2 seconds.
‘The machine is locked.’ is briefly displayed.
‘Fill water tank’
Programming mode is disabled.
To enable programming mode again, remove the water tank. Then
press the Rotary Switch, the P button and the bottom right-hand
button simultaneously for about 2 seconds. ‘The machine is
enabled.’ is briefly displayed. Programming mode is enabled again.
26
4
Product settings
Permanent settings in programming mode
In the program item ‘Product settings (2/6)’ / ‘Expert mode’ you can
make individual settings for all specialty coffees, milk and hot water.
J WARNING
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water an
seek medical attention.
T Keep children AWAY.
The following settings can be made:
Product
Ristretto,
espresso,
coffee
Temperature
‘Normal’, ‘High’
Two ristretti,
‘Normal’, ‘High’
two espressi,
two coffees
Latte macchiato, ‘Normal’, ‘High’
cappuccino
Portion of milk
Hot water
–
‘Low’, ‘Normal’,
‘X high’
Coffee strength
‘extra-mild’ ;, ‘mild’ ;;,
‘normal’ ;;;, ‘strong’ ;;;;,
‘extra-strong’ ;;;;;
–
‘extra-mild’ ;, ‘mild’ ;;,
‘normal’ ;;;, ‘strong’ ;;;;,
‘extra-strong’ ;;;;;
–
–
Amount
Volume:
‘0.5 oz’ – ‘8.0 oz’
(25 ml – 240 ml)
Volume:
‘0.5 oz’ – ‘8.0 oz’
(25 ml – 240 ml) (per cup)
Amount of milk:
‘3 sec.’ – ‘120 sec.’
Interval: ‘0 sec.’ – ‘60 sec.’
Volume: ‘0.5 oz’ – ‘8.0 oz’
(25 ml – 240 ml)
‘3 sec.’ – ‘120 sec.’
‘0.5 oz’ – ‘15.0 oz’
(25 ml – 450 ml)
Example: Proceed as follows to change the amount of milk for a
latte macchiato from ‘16 sec.’ to ‘20 sec.’, the interval from ‘30 sec.’
to ‘40 sec.’ and the amount of water from ‘1.5 oz’ (45 ml) to ‘1.0 oz’
(40 ml).
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Product settings (2/6)’ is displayed.
T Press the ‘Expert mode’ button.
‘Expert mode’
27
4
Permanent settings in programming mode
E Next select the button of the product for which you would like
to make settings. No product is prepared at this point.
T Press the ‘Latte macchiato’ button.
‘Latte macchiato’
T Press the ‘Amount of milk’ button.
T Press the ‘ < ’ or ‘ > ’ button to change setting for the amount
of milk to ‘20 sec.’.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
T Press the ‘Volume’ button.
T Press the ‘ < ’ or ‘ > ’ button to change setting for the fill volume to ‘1.0 oz’ (40 ml).
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
T Press the ‘Next’ button.
T Press the ‘Interval’ button.
T Press the ‘ < ’ or ‘ > ’ button to change setting for the interval
to ‘40 sec.’.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Latte macchiato’
O T Press the P button to exit programming mode.
‘Please select product:’
Enable or disable one-off
settings
In the program item ‘Product settings (2/6)’ / ‘One-off settings’ you
can make the following setting:
‘Active’
U One-off settings can be made during preparation (e.g. coffee
strength or amount of water).
‘Inactive’
U One-off settings cannot be made during preparation. The
product is prepared according to the settings in programming mode (‘Product settings (2/6)’ / ‘Expert mode’).
U
U
Example: Proceed as follows to disable one-off settings during preparation.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
28
4
Permanent settings in programming mode
g T Turn the Rotary Switch until the program item ‘Product settings (2/6)’ is displayed.
T Press the ‘One-off settings’ button.
‘One-off settings’
T Press the ‘Inactive’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Product settings (2/6)’
O T Press the P button to exit programming mode.
‘Please select product:’
One-off settings cannot now be made during preparation.
Enabling and disabling
product selector view
In the program item ‘Product settings (2/6)’ / ‘product selector’ you
can make the following setting:
‘Active’
U Product selector view is active and can be started by turning
the Rotary Switch g when the IMPRESSA is ready for use.
‘Inactive’
U Product selector view is inactive.
U
U
Example: Proceed as follows to disable product selector view.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Product settings (2/6)’ is displayed.
T Press the ‘product selector’ button.
‘product selector’
T Press the ‘Inactive’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Product settings (2/6)’
O T Press the P button to exit programming mode.
‘Please select product:’
Product selector view can now no longer by started by turning the Rotary Switch.
29
4
Permanent settings in programming mode
Enabling and disabling
products
In the program item ‘Product settings (2/6)’ / ‘Lock/enable’ you can
enable or disable each individual product.
Example: For example, you can disable the preparation of hot water.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Product settings (2/6)’ is displayed.
T Press the ‘Lock/enable’ button.
‘Lock/enable’
E The lock symbol indicates whether the product is enabled or
disabled. If the lock is closed, the product is disabled.
T Press the ‘Next’ button until the product ‘Hot water’ is displayed.
T Press the ‘Hot water’ button.
The lock is closed. Hot water preparation is now disabled.
O T Press the P button to exit programming mode.
‘Please select product:’
On the start screen, ‘Hot water’ is greyed out.
Maintenance settings
In the program item ‘Maintenance settings (3/6)’ you can make the
following settings:
‘Filter’
U Activate the CLEARYL Pro Blue filter cartridge (see Chapter 5
‘Maintenance – Inserting and activating the filter’).
‘Water hardness’
U If you do not have a filter cartridge, you will need to set the
water hardness (see Chapter 4 ‘Permanent settings in programming mode – Setting the water hardness’).
‘Switch-on rinse’ / ‘Manual’
U The switch-on rinse must be started manually.
‘Switch-on rinse’ / ‘Automatic’
U The switch-on rinse is started automatically.
‘Rinse the milk system’ / ‘After 10 min’
U You are prompted to rinse the milk system 10 minutes after
preparation of a specialty coffee with milk.
U
U
U
U
U
30
4
U
Permanent settings in programming mode
‘Rinse the milk system’ / ‘Immediate’
U You are prompted to rinse the milk system immediately
after preparation of a specialty coffee with milk.
Example: Proceed as follows to make the machine prompt you to
rinse the milk system immediately after preparing a specialty coffee
with milk.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Maintenance
settings (3/6)’ is displayed.
T Press the ‘Rinse the milk system’ button.
‘Rinse the milk system’
T Press the ‘Immediate’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Maintenance settings (3/6)’
O T Press the P button to exit programming mode.
‘Please select product:’
Setting the water
hardness
E If you are using the CLEARYL Pro Blue filter cartridge and have
activated it, it is not possible to set the water hardness.
The harder the water is, the more frequently the IMPRESSA needs to
be descaled. It is therefore important to set the water hardness accurately.
The water hardness can be adjusted on a continuous scale between
1 °dH and 30 °dH.
Example: Proceed as follows to change the water hardness from
‘16 °dH’ to ‘25 °dH’.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Maintenance
settings (3/6)’ is displayed.
T Press the ‘Water hardness’ button.
‘Water hardness’
31
4
Permanent settings in programming mode
T Press the ‘ < ’ or ‘ > ’ button to set the water hardness.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Maintenance settings (3/6)’
O T Press the P button to exit programming mode.
‘Please select product:’
Energy-saving mode
In the program item ‘Machine settings (4/6)’ / ‘Save energy’ you can
permanently set an energy-saving mode (Energy Save Mode,
E.S.M.©):
‘Active’
U Soon after the last preparation, the IMPRESSA stops heating
up. After about 5 minutes the message ‘Energy Save’ is displayed.
U Before you can prepare a specialty coffee, specialty coffee
with milk, or hot water, the machine must heat up.
‘Inactive’
U All specialty coffees, specialty coffees with milk and hot
water can be prepared without having to wait.
U
U
Example: Proceed as follows to change the energy-saving mode
from ‘Active’ to ‘Inactive’.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Machine settings (4/6)’ is displayed.
T Press the ‘Save energy’ button.
‘Save energy’
T Press the ‘Inactive’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Machine settings (4/6)’
O T Press the P button to exit programming mode.
‘Please select product:’
32
4
Automatic switch-off
Permanent settings in programming mode
By instructing your IMPRESSA to automatically switch itself off, you
can cut down your energy consumption. If this function is activated,
your IMPRESSA switches off automatically after the preset time following the last action on the machine.
You can set the automatic switch-off to 15 minutes, 30 minutes
or 1–15 hours.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Machine settings (4/6)’ is displayed.
T Press the ‘Switch off after’ button.
‘Switch off after’
T Press the ‘ < ’ or ‘ > ’ button to change the setting.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Machine settings (4/6)’
O T Press the P button to exit programming mode.
‘Please select product:’
Unit for amount of water
You can change the unit for the amount of water from ‘oz’ to ‘ml’.
Example: Proceed as follows to change the unit for the amount of
water from ‘oz’ to ‘ml’.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Machine settings (4/6)’ is displayed.
T Press the ‘Units’ button.
‘Units’
T Press the ‘ml’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Machine settings (4/6)’
O T Press the P button to exit programming mode.
‘Please select product:’
33
4
Permanent settings in programming mode
Restore factory settings
In the program item ‘Machine settings (4/6)’ / ‘Factory setting’ you
can reset various settings to their factory settings:
‘Machine’
U All user settings (apart from the ‘filter’ and ‘water hardness’)
are reset to factory settings. Your IMPRESSA then switches off.
‘Product’
U The settings (amount of water, coffee strength, temperature
etc.) for any product can be reset individually to the factory
settings. The corresponding double product is also reset to
the factory settings at the same time.
‘All products’
U The settings (amount of water, coffee strength, temperature
etc.) for all products are reset to the factory settings.
‘Display settings’
U All display settings are reset to the factory settings.
U
U
U
U
Example: Proceed as follows to reset the values for ‘Espresso’ to the
factory settings.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Machine settings (4/6)’ is displayed.
T Press the ‘Factory setting’ button.
‘Factory setting’
T Press the ‘Product’ button.
‘Product’
T Press the ‘Espresso’ button.
‘Espresso’ / ‘Reset this product to the factory setting?’
T Press the ‘Yes’ button.
‘Saved’ appears briefly on the display.
‘Machine’
O T Press the P button to exit programming mode.
‘Please select product:’
34
4
Language
Permanent settings in programming mode
In this program item you can set the language used by your
IMPRESSA.
E If you choose the wrong language by mistake, you can easily
reset the machine to ‘English’: Press the P button to enter programming mode. Use the Rotary Switch g to select program
item ‘5/6’ and then press the top left-hand button.
Example: Proceed as follows to change the language from ‘English’
to ‘Deutsch’.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Machine settings (5/6)’ is displayed.
T Press the ‘Choose language’ button.
‘Choose language’
T Press the ‘Deutsch’ button.
‘Gespeichert’ appears briefly on the display.
‘Geräteeinstellungen (5/6)’
O T Press the P button to exit programming mode.
‘Bitte wählen Sie Ihr Produkt:’
Background color
In this program item you can set the background color for the display of your IMPRESSA.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Machine settings (5/6)’ is displayed.
T Press the ‘Colour scheme’ button.
‘Colour scheme’
T Press the ‘ < ’ or ‘ > ’ button to change the setting.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Machine settings (5/6)’
35
4
Permanent settings in programming mode
O T Press the P button to exit programming mode.
‘Please select product:’
E The selected background color only applies on the selection
page of the display showing the specialty coffees.
Querying information
In the program item ‘Information (6/6)’ you can view the following
information.
‘Product counter’: Number of prepared coffee specialty coffees, specialty coffees with milk and hot water
‘Maintenance counter’: Maintenance status and number of
maintenance programs performed (cleaning, descaling,
changing the filter)
‘Day counter’: Number of prepared coffee specialty coffees,
specialty coffees with milk and hot water. This counter can be
reset to zero.
‘Version’: Software version
U
U
U
U
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Information
(6/6)’ is displayed.
T Press the ‘Product counter’ button.
The number of specialty coffees prepared is displayed.
E You can also view the number of products prepared in the
product selector. To do this, turn the Rotary Switch.
T Press the ‘’ button.
‘Information (6/6)’
E To reset the day counter to zero, press the ‘Day counter’ button. Then press the ‘’ button and confirm by pressing ‘Yes’.
O T Press the P button to exit programming mode.
‘Please select product:’
36
5
5
Maintenance
Maintenance
J WARNING
Use of maintenance products that are harmful to health and discharge of liquids during maintenance program. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Keep children away from the machine while it is performing a
maintenance program.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T When using do not eat or drink.
T Keep maintenance products away from food, drink and animal food.
T Keep container tightly closed and dry. Keep in a cool place.
Your IMPRESSA has the following integrated maintenance programs:
Rinsing the machine (‘Rinse the coffee system’)
Rinsing the cappuccino frother (‘Rinse the milk system’)
Cleaning the cappuccino frother (‘Clean the milk system’)
Changing the filter (‘Change the filter’) (only if filter is activated)
Cleaning the machine (‘Clean’)
Descaling the machine (‘Descale’)
U
U
U
U
U
U
E Clean or descale the machine, rinse the milk system or change
the filter when you are prompted to do so.
E Press the P button to view a list of the maintenance programs
(‘Maintenance status (1/6)’). By referring to the bar you can see
which maintenance program is due. When the bar is completely filled with red, your IMPRESSA will prompt you to perform the appropriate maintenance program.
E The IMPRESSA will not prompt you to clean the milk system.
In the interests of hygiene, you should clean the milk system
daily when you have been preparing milk.
37
5
Maintenance
Rinsing the machine
You can initiate the rinse operation manually at any time.
Precondition: ‘Please select product:’ is displayed.
T Place a receptacle under the coffee spout.
O T Press the P button.
‘Maintenance status (1/6)’
T Press the ‘Rinse the coffee system’ button.
‘Machine is rinsing.’, water flows out of the coffee spout.
The rinse stops automatically. ‘Please select product:’
appears on the display.
Rinsing the cappuccino
frother
After each milk preparation, the IMPRESSA prompts you to rinse the
milk system.
Precondition: ‘Rinse the milk system’ is displayed.
T Place a receptacle under the cappuccino frother.
k T Press the Rotary Switch.
‘Milk system is being rinsed.’, water flows out of the cappuccino frother.
The rinse stops automatically and ‘Please select product:’
appears on the display.
38
5
Maintenance
Cleaning the cappuccino
frother
To ensure that the cappuccino frother always works properly, you
must clean it daily when you have been preparing milk. Your
IMPRESSA will not prompt you to clean the cappuccino frother.
J WARNING
Non-recommended cleaning agents will not optimally remove milk
residues. This may cause the cappuccino frother to become blocked
and fly off the machine. Discharge of hot steam.
T Use only original JURA milk system cleaner.
J WARNING
Harmful and irritating cleaning agent. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water
and seek medical advice.
T If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice
immediately and show label.
E JURA milk system cleaner is available from specialized dealers.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
T Press the ‘Clean the milk system’ button.
‘Cleaning agent for milk system’
T Pour 8.5 oz (250 ml) of fresh water into a receptacle and add
one capful of milk system cleaner.
T Immerse the milk pipe in the receptacle.
T Turn the setting wheel of the cappuccino frother to the Milk
Foam ü or Milk z position.
T Place another receptacle under the cappuccino frother.
T Press the ‘Next’ button.
‘Milk system is being cleaned.’, water flows out of the cappuccino frother.
‘Water for cleaning milk system’
T Rinse the receptacle thoroughly, fill it with 8.5 oz (250 ml) of
fresh water and immerse the milk pipe in the water.
39
5
Maintenance
T Empty the other receptacle and place it under the cappuccino frother again.
T Press the ‘Next’ button.
‘Milk system is being cleaned.’, the cappuccino frother and
the pipe are rinsed with fresh water.
‘Please select product:’ appears on the display.
Dismantling and rinsing
the cappuccino frother
T Carefully pull the cappuccino frother down and off.
T Dismantle the cappuccino frother into its individual parts.
T Rinse all parts of the cappuccino frother thoroughly under
running water.
T Reassemble the cappuccino frother.
E Ensure that all individual parts are correctly and firmly connected to ensure correct operation of the cappuccino frother.
T Firmly attach it to the connector.
Inserting and activating
the filter
Your IMPRESSA no longer has to be descaled if you are using the
CLEARYL Pro Blue filter cartridge. If the water hardness is 10 °dH or
more, we recommend using the filter cartridge. If you do not know
the hardness of your water, you can find this out first (see Chapter 1
‘Preparing and using for the first time – Determining the water hardness’).
If you did not activate the filter cartridge the first time you used the
machine, you can do this now as follows.
E Perform the ‘inserting the filter’ operation without any interruptions. This will ensure that your IMPRESSA always produces
its best.
Precondition: ‘Please select product:’ is displayed.
O T Press the P button.
‘Maintenance status (1/6)’
g T Turn the Rotary Switch until the program item ‘Maintenance
settings (3/6)’ is displayed.
T Press the ‘Filter’ button.
‘Filter’
T Press the ‘Active’ button.
40
5
Maintenance
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Insert filter’
T Remove and empty the water tank.
T Open the filter holder and insert the filter cartridge into the
water tank, exerting slight pressure.
T Close the filter holder. It will click into place audibly.
E After two months, the filter will cease to work. Set the date on
the date plate on the filter holder in the water tank.
T Fill the water tank with fresh, cold water and reinsert the tank.
T Place a receptacle under the hot-water nozzle.
T Press the ‘Next’ button.
‘Filter is being rinsed.’, water flows out of the hot-water nozzle.
E You can interrupt rinsing of the filter at any time by pressing
any button. Press the Rotary Switch k to continue rinsing of
the filter.
E The water may be slightly discolored. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically. The machine heats
up.
‘Please select product:’
Your IMPRESSA is once more ready for use.
Changing the filter
E After 4058 oz (120 liters) of water have flowed through, the filter will cease to work. Your IMPRESSA will automatically
prompt you to change the filter.
E After two months, the filter will cease to work. Set the date on
the date plate on the filter holder in the water tank.
E If the CLEARYL Pro Blue filter cartridge is not activated in programming mode, you will not be prompted to change the filter.
Precondition: ‘Please select product:’ is displayed. The c symbol is
also displayed.
O T Press the P button.
‘Maintenance status (1/6)’
41
5
Maintenance
T Press the ‘Change the filter’ button.
‘Change the filter’
E If you do not want to start changing the filter just yet, press
the ‘’ button.
T Press the ‘Next’ button.
‘Change filter’
T Remove and empty the water tank.
T Open the filter holder and remove the old CLEARYL filter cartridge.
T Insert the New filter cartridge into the water tank, exerting
slight pressure.
T Close the filter holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert the tank.
T Place a receptacle (at least 17 oz or 500 ml) under the hotwater nozzle.
T Press the ‘Next’ button.
‘Filter is being rinsed.’, water flows out of the hot-water nozzle.
E You can interrupt rinsing of the filter at any time by pressing
any button. Press the Rotary Switch k to continue rinsing of
the filter.
E The water may be slightly discolored. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
17 oz (500 ml). The machine heats up. ‘Please select product:’
appears on the display.
Cleaning the machine
J WARNING
42
After 200 preparations or 80 switch-on rinses, the IMPRESSA will
prompt you to clean it.
Non-recommended (e.g. liquid) cleaning agents may contain substances that could damage the machine or leave residues.
T Use only original JURA cleaning tablets. These are specially
formulated for your machine.
5
J WARNING
Maintenance
Harmful and irritating cleaning agent. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water
and seek medical advice.
T If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice
immediately and show label.
E The cleaning program lasts approximately 20 minutes.
E Do not interrupt the cleaning program. The quality of cleaning
will be impaired if you do so.
E JURA cleaning tablets are available from specialized dealers.
Precondition: ‘Please select product:’ is displayed. The c symbol is
also displayed.
O T Press the P button.
‘Maintenance status (1/6)’
T Press the ‘Clean’ button.
‘Clean’
E If you do not want to start cleaning just yet, press the ‘’ button.
T Press the ‘Next’ button.
‘Empty drip tray’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Please press the Rotary Switch.’
T Place one receptacle under the coffee spout and another
under the cappuccino frother.
k T Press the Rotary Switch.
‘Machine is being cleaned.’, water flows out of the coffee
spout.
The operation is interrupted, ‘Add cleaning tablet’.
43
5
Maintenance
T Open the cover of the filler funnel for ground coffee.
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel.
‘Please press the Rotary Switch.’
k T Press the Rotary Switch.
‘Machine is being cleaned.’, water flows repeatedly out of
the coffee spout and the cappuccino frother.
The operation is interrupted, ‘Empty drip tray’.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
Cleaning is now complete. Your IMPRESSA is once more
ready for use.
Descaling the machine
J WARNING
Non-recommended descaling agents (e.g. vinegar) may contain
substances that could damage the machine or leave residues.
T Use only original JURA descaling tablets. These are specially
formulated for your machine.
J WARNING
Harmful and irritating descaling agent. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water.
Remove contact lenses. Seek medical advice.
T If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice
immediately and show label.
NOTICE
44
The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of
calcification depends on the hardness of your water.
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling program to run to the end.
5
Maintenance
E The descaling program lasts approximately 50 minutes.
E JURA descaling tablets are available from specialized dealers.
E If you use a CLEARYL Pro Blue filter cartridge and this is activated, you will not be prompted to descale.
E If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out. Clean up any
splashes immediately.
Precondition: ‘Please select product:’ is displayed. The c symbol is
also displayed.
O T Press the P button.
‘Maintenance status (1/6)’
T Press the ‘Descale’ button.
‘Descale’
E If you do not want to start descaling just yet, press the ‘’ button.
T Press the ‘Next’ button.
‘Empty drip tray’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Pour descaling agent into water tank’
T Remove and empty the water tank.
T Completely dissolve 3 JURA descaling tablets in a receptacle
holding 20 oz (600 ml) of water. This may take several minutes.
T Pour the solution into the empty water tank and insert it into
the machine.
‘Please press the Rotary Switch.’
T Remove the cappuccino frother.
T Place a receptacle under the connector of the cappuccino
frother and another under the hot-water nozzle.
k T Press the Rotary Switch.
‘Machine is being descaled.’, water flows repeatedly out of
the connector of the cappuccino frother and the hot-water
nozzle.
The operation is interrupted, ‘Empty drip tray’.
T Empty both receptacles.
45
5
Maintenance
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Fill water tank’
T Remove the water tank and rinse it thoroughly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
‘Please press the Rotary Switch.’
T Refit the cappuccino frother.
T Place a receptacle under the cappuccino frother, the coffee
spout and the hot-water nozzle.
k T Press the Rotary Switch.
‘Machine is being descaled.’, water flows out of the hot-water
nozzle and the cappuccino frother.
‘Machine is heating.’, ‘Machine is rinsing.’, water flows out of
the coffee spout.
The operation stops automatically, ‘Empty drip tray’.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
Descaling is now complete. Your IMPRESSA is once more
ready for use.
E If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
Cleaning the bean
container
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These traces may negatively affect
the coffee result. For this reason clean the bean container from time
to time.
Precondition: ‘Fill bean container’ is displayed.
Q T Switch the machine off with the On/Off button.
3 T Switch the machine off at the power switch.
T Remove the aroma preservation cover.
T Clean the bean container with a soft, dry cloth.
T Fill the bean container with coffee beans and close the aroma
preservation cover.
46
5
Descaling the water tank
Maintenance
Limescale deposits may form in the water tank. To ensure correct
function of the machine, descale the water tank from time to time.
T Remove the water tank.
T If you use a CLEARYL Pro Blue filter cartridge, remove this.
T Descale the tank with a mild conventional descaling agent
in accordance with the manufacturer's instructions.
T Rinse out the water tank thoroughly.
T If you use a CLEARYL Pro Blue filter cartridge, insert this
again.
T Fill the water tank with fresh, cold water and reinsert the tank.
47
6 Display messages
6 Display messages
Message
‘Fill water tank’
Cause/Result
The water tank is empty. You
cannot prepare any products.
‘Empty coffee
grounds
container’
The coffee grounds container is
full. You cannot prepare any
products.
T Empty the coffee grounds container
and the drip tray (see Chapter 3 ‘Daily
operation – Daily maintenance’).
‘Empty drip tray’
The drip tray is full. You cannot
prepare any products.
T Empty the drip tray and the coffee
grounds container.
T Clean and dry the metal contacts on
the back of the drip tray.
‘Drip tray not
fitted’
The drip tray is not inserted
correctly or is not inserted at all.
You cannot prepare any
products.
The IMPRESSA is prompting you
to perform a rinse or continue a
maintenance program that was
already started.
The bean container is empty.
You cannot prepare any
products.
T Fit the drip tray.
‘Rinse the milk
system’
The IMPRESSA is prompting you
to rinse the milk system.
T Press the Rotary Switch to start rinsing
the milk system.
‘Please select
product:’ is
displayed.
The c symbol is
also displayed.
The IMPRESSA is prompting you
to perform a maintenance
program.
T Press the P button to view the list of
maintenance programs (‘Maintenance
status (1/6)’). By referring to the bar you
can see which maintenance program is
due. When the bar is completely filled
with red, your IMPRESSA will prompt you
to perform the appropriate maintenance
program.
‘Not enough
ground coffee’
There is insufficient ground
coffee in the machine; the
IMPRESSA stops the operation.
T The next time you prepare a beverage,
add more ground coffee (see Chapter 2
‘Preparation – Ground coffee’).
‘Please press the
Rotary Switch.’
‘Fill bean
container’
48
Action
T Fill the water tank (see Chapter 1
‘Preparing and using for the first time –
Filling the water tank’).
T Press the Rotary Switch to start the
rinse or to continue the maintenance
program.
T Fill the bean container (see Chapter 1
‘Preparing and using for the first time –
Filling the bean container’).
7
7
Troubleshooting
Troubleshooting
Problem
When preparing a latte
macchiato, the typical
three layers do not
form.
Cause/Result
Insufficient foam is
produced when the
milk is frothed or milk
sprays from the
cappuccino frother.
The cappuccino frother is
dirty.
T Rinse and clean the cappuccino
frother (see Chapter 5 ‘Maintenance –
Rinsing the cappuccino frother’).
T Check that the air intake pipe is fitted
on the cappuccino frother.
T Rinse or replace the air intake pipe. You
will find a replacement in the Welcome
Pack.
Coffee only comes out
in drips when it is
being prepared.
Coffee or ground coffee has
been ground too finely and
is blocking the system. The
same filter cartridge may
have been used several
times or the water hardness
set incorrectly in the
programming mode.
The CLEARYL Pro Blue filter
cartridge is activated.
T Put the grinder on a coarser setting or
use coarser ground coffee (see Chapter 1
‘Preparing and using for the first time –
Adjusting the grinder’).
T Perform descaling (see Chapter 5
‘Maintenance – Descaling the machine’).
The sliding catch for the
bean container has not
been pulled out or has not
been pulled out completely.
The metal contacts of the
drip tray are dirty or wet.
T Pull the sliding catch on the right-hand
side of the bean container fully out.
Water hardness cannot
be adjusted.
‘Fill bean container’ is
displayed although the
bean container is full.
‘Empty drip tray’ is
always displayed.
‘Fill water tank’ is
displayed although the
water tank is full.
Action
–
The water tank float is
trapped.
T Turn the setting wheel of the cappuccino frother to the far right and the Milk
Foam position ü.
T Change the length of the interval to at
least 30 seconds in programming mode
(see Chapter 4 ‘Permanent settings in
programming mode – Product settings’).
T Deactivate the filter cartridge in
programming mode.
T Clean and dry the metal contacts on
the back of the drip tray.
T Descale the water tank (see Chapter 5
‘Maintenance – Descaling the water
tank’).
49
7
Troubleshooting
Problem
Little or no water or
steam comes out of
the cappuccino frother.
The pump is very
quiet.
Cause/Result
The connector of the
cappuccino frother may be
blocked by milk residues or
limescale fragments
loosened during descaling.
Grinder is making a
very loud noise.
There are foreign objects in
the grinder.
T Contact customer support in your
country (see Chapter 11 ‘JURA contact
details / Legal information’).
‘ERROR 2’ is displayed.
If the machine was exposed
to the cold for a long period
of time, heating is disabled
for safety reasons.
–
T Warm the machine at room temperature.
Other ‘ERROR’
messages are displayed.
Action
T Remove the cappuccino frother.
T Unscrew the black connector with the
aid of the hexagonal hole on the
measuring spoon for ground coffee.
T Clean the connector thoroughly.
T Screw the connector back on by hand.
T Carefully tighten it using the hexagonal
hole on the measuring spoon, turning by
no more than a quarter of a rotation.
T Switch the IMPRESSA off at the power
switch. Contact customer support in
your country (see Chapter 11 ‘JURA
contact details / Legal information’).
E If you were unable to solve the problem, contact customer
support in your country (see Chapter 11 ‘JURA contact details /
Legal information’).
50
8
8
Transport and environmentally friendly disposal
Transport and environmentally friendly disposal
Transport / Emptying the
system
In order to protect the IMPRESSA from frost during transport, the
system must be emptied.
Precondition: ‘Please select product:’ is displayed.
T Carefully pull the cappuccino frother down and off.
T Place a receptacle under the connector of the cappuccino
frother.
T Press the ‘1 portion milk’ button.
‘1 portion milk’, hot steam is discharged from the connector.
T Remove and empty the water tank.
g T Turn the Rotary Switch until ‘60 sec.’ is displayed.
Steam will continue to be discharged from the connector
until the system is empty.
‘Fill water tank’
Q T Press the On/Off button.
The IMPRESSA is switched off.
Disposal
Please dispose of old machines in an environmentally neutral way.
H
51
9 Technical data
9 Technical data
Voltage
Power
Airborne noise emitted
Ambient conditions
120 V ~, 60 Hz
1450 W
LP < 70 dB (A)
Humidity max. 80%
Ambient temperature
50 – 95 °F
(10 – 35 °C)
Conformity mark
Energy consumption
‘Save energy’ / ‘Active’
Energy consumption
‘Save energy’ / ‘Inactive’
Pump pressure
Holding capacity of water tank
Holding capacity of bean container
Holding capacity of coffee grounds
container
Cord length
Weight
Dimensions (W  H  D)
approx. 4.1 Wh
approx. 10.6 Wh
Static, max. 15 bar
135 oz
(4 l)
17.6 oz
(500 g)
max. 40 portions
approx. 43.3 in.
(approx. 1.1 m)
approx. 29 lb
(approx. 12.8 kg)
13.4  19.7  17.3 in.
(33.8  49.7  43.2 cm)
Information for testers (repeat test in accordance with DIN VDE
0701-0702): The central grounding point (CGP) is located on the back
of the machine below the JURA logo (turn JURA logo anti-clockwise).
Directives
52
The machine complies with the following directives:
Standard UL 1082
Canadian Standard CSA C22.2 No. 64
U
U
10
10
A
B
C
Index
Index
Addresses 56
Aroma preservation cover
Bean container with aroma preservation
cover 8
Automatic switch-off 33
Background color 35
Bean container
Bean container with aroma preservation
cover 8
Cleaning 46
Filling 11
Button
On/Off button 9
P button (programming) 9
Cappuccino 19
Cappuccino frother
Cleaning 39
Rinsing 38
Cleaning
Bean container 46
Cappuccino frother 39
Machine 42
CLEARYL Pro Blue filter cartridge
Changing 41
Inserting and activating the filter 40
Coffee 18
Coffee grounds container 8
Coffee spout
Height- and width-adjustable coffee
spout 8
Consistency of grind
Adjusting the grinder 15
Grinder adjustment switch 8
Contact details 56
Cover
Storage compartment 8
Water tank 8
Cup platform 8
Customer support 56
D
E
F
G
H
I
Descaling
Machine 44
Water tank 47
Display 9
Display messages 48
Display settings 35
Disposal 51
Double product 19
Drip tray 8
Emptying the system 51
Energy-saving mode 32
Errors
Troubleshooting 49
Espresso 18
Factory settings
Restore factory settings 34
Filler funnel
Filler funnel for ground coffee 8
Filling
Bean container 11
Water tank 11
Filter
Changing 41
Inserting and activating the filter 40
First-time use 12
Frother
Cappuccino frother 8
Grinder adjustment switch 8
Ground coffee 20
Measuring spoon for ground coffee 8
Hotline 56
Hot water 22
Hot-water nozzle 8
Important safeguards
Safety 4
Instant coffee
Ground coffee 20
Internet 10
53
10
J
L
M
P
Index
Product settings 27
Programming mode 25
Automatic switch-off 33
Background color 35
Energy-saving mode 32
Language 35
Maintenance settings 30
Product settings 27
Querying information 36
Restore factory settings 34
Setting the water hardness 31
Unit for amount of water 33
JURA
Contact details 56
Internet 10
Language 35
Latte macchiato 19
Machine
Cleaning 42
Descaling 44
Rinsing 38
Setting up 10
Switching off 24
Switching on 23
Maintenance 37
Daily maintenance 23
Maintenance settings 30
Measuring spoon for ground coffee 8
Messages, display 48
Milk
Connecting milk 16
Milk foam 20
Milk system cleaning
Cleaning the cappuccino frother 39
Milk system rinsing
Rinsing the cappuccino frother 38
Milk, warm 20
Permanently setting the water for the cup
size 21
Permanent settings in programming mode
25
Power cord 9
Power switch 9
Preparation 17, 19
Cappuccino 19
Coffee 18
Espresso 18
Ground coffee 20
Hot water 22
Latte macchiato 19
Milk 20
Two specialty coffees 19
Problems
Troubleshooting 49
54
Q
R
S
T
U
Querying information 36
Rinsing
Cappuccino frother 38
Machine 38
Rotary Switch 9
Safety
Important safeguards 4
Settings
Maintenance settings 30
Permanent settings in programming
mode 25
Setting up
Setting up the machine 10
Switching off
Machine 24
Switching on
Machine 23
Switch-off
Automatic switch-off 33
Symbol description 3
Technical data 52
Tel 56
Transport 51
Troubleshooting 49
Two products 19
Unit for amount of water 33
Use, First-time 12
10
Index
W
Warm milk 20
Water hardness
Determining the water hardness 15
Setting the water hardness 31
Water tank 8
Descaling 47
Filling 11
Website 10
55
J70565/XJ9/US-en/201704
11 JURA contact details / Legal information
11 JURA contact details / Legal information
JURA Elektroapparate AG
Kaffeeweltstrasse 10
CH-4626 Niederbuchsiten
Switzerland
USA: JURA Inc.
Canada: FAEMA
Phone
E-Mail
1-800-220-5701
info@us.jura.com
1-(855)-544-8600
info@juracanada.ca
Opening Hours (EST)
Mon – Thu 9 am – 9 pm
Fri 9 am – 8 pm
Sat 9 am – 5 pm
Distributor Address
Phone
Fax
20 Craig Road
Montvale, NJ 07645
001 (201) 767-3999
001 (201) 767-9684
115 Matheson Boulevard East
Mississauga, Ontario, L4Z 1X8
1-(905)-501-8600
Internet
www.jura.com
www.ca.jura.com
Customer Service
@ You will find additional contact details for your country at
www.jura.com.
Technical changes
56
We reserve the right to make technical changes. The diagrams used
in these instructions for use are for illustration purposes only and do
not represent the original colors of the machine. Some details of
your IMPRESSA may vary.
Feedback
Your opinion is important to us! Use the contact link at
www.jura.com.
Copyright
The instructions for use contain information which is protected by
copyright. It is not permitted to photocopy these instructions for use
or translate them into another language without the prior written
consent of JURA Elektroapparate AG.
Download PDF
Similar pages