Mateo™ Single Lever Commercial Style Kitchen Faucet

I N S TA L L AT I O N MA N UA L
Mateo™ Single Lever
Commercial Style Kitchen Faucet
KPF-2630
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 25, 2015
Thank you for purchasing Kraus
We would like to take this opportunity to thank you for your business with Kraus
USA. It is our sincere hope that you are completely satisfied with your experience.
We welcome any questions or comments you may have, and will be glad to assist
you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com
Please register your new Kraus product at the following web address in order to
activate the warranty and receive the full benefit of customer support:
www.kraususa.com/registration
Sincerely,
Kraus Customer Service Department
1
7/8”
(22mm)
19.7
º
Prior to Installation:
•
10 1/8”
8 5/16”
Make(257mm)
sure you have all necessary (21mm)
parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
∅ 1 15/16”
775-0703 for a replacement
(∅ 50mm)
∅ 1 3/4”
•
(∅ 45mm)
∅ 1 15/16”
(∅ 50mm)
•
•
1 3/8”
(35mm)
Turn off the hot and cold water supply at
the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
Place bucket under angle stops. Turn on to flush any debris prior to installing new
plumbing. Shut off angle stops
•
Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)
•
Max countertop thickness without deck plate: 1-1/2”
•
Max countertop thickness with deck plate: 1”
1A
Without deck plate:
1 1/4-18UNF-2A
9/16”-18UNEF
1/16” (1mm) min.
1-1/2” (38 mm) max.
D
Tools You Will Need
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
With deck plate:
1/16” (1mm) min.
1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
Adjustable wrench
Half Moon Locking Nut
Tools you will need:
2
B
3
G
Safety Goggles
Adjustable Wrench
G
F
G
E
G
Bucket
2
G
E
F
F
B
Silicone Sealant
Silicone
Sealant
D
J
Diagram and Parts List
B
A
F
D
E
3
C
A. Spray Head
E. Hot & Cold Waterlines
B. Faucet Body
F. Hex Wrench Set
C. Deck & Putty Plate
F1. 2.5mm
D. Base
F2. 4mm
Faucet Dimensions
11.06”
(280.3mm)
9.25”
(234.3mm)
20.7”
(526mm)
2.5”
(64mm)
10.25”
(260.5mm)
0.06”~1”
(1mm~25.4mm)
8.9”
(226mm)
2.43”
(62mm)
9/16-24UNEF
(3/8” Compression)
24.3”
(618mm)
Ø1.8”
(Ø46mm)
7.3”
(186.4mm)
4.125”
(105mm)
3.06”
(78.4mm)
4
1A
Step 1A: Install base without deck & putty plate
1B
Insert base (D) into sink or
countertop with “FR↑NT” facing
forward. Tighten
screws on base
C
(D) with 4mm hex wrench (F)
until base is secure on sink or
1
countertop
D
Half Moon Locking Nuts
Installer Tip: Rotate the
two half-moon shaped
locking nuts inward before
inserting base (D) into sink or
countertop
B
C
2
1
D
J
D
Place a bead of clear silicone
sealant (not included) around the
edge of the putty plate (C). Secure
deck & putty plate (C) on sink or
countertop. Insert base (D) into
hole of deck & putty plate (C) with
“ FR↑NT” facing forward. Tighten
screws on base (D) with
G 4mm hex
wrench (F) until base is secure on
deck & putty plate (C)
Hot
Half Moon Locking Nuts
4
6
Half Moon Lo
4
Step 1B:3Install base with deck & putty plate
1B
2
Installer Tip: Rotate the two
half-moon shaped locking
nuts inward before inserting
base (D) into deck plate (C)
5
A
E
G
Cold
4
3
4
3
E
Step 2: Install faucet
E
E E
E
Insert hot & cold waterlines (E),E
one by one, in large hole of base
B
J
B
D
E
3
E
D
4
E
E
4
4
Step 3: Secure faucet
5
5
E
5
6
E
J
E
BE
B
DD
Cold
E
Align arrow on faucet body
(B)
6B
with arrow on base (D). Attach
faucet body (B) to base (D)Dand
turn counter-clockwise. Secure
faucet body (B) by tightening
the set screw with 2.5mm hex
wrench (J) A
Installer Tip: Please loosen
A
set screw from faucet
body (B)
6
prior to securing to base (D)
E
5
J
J
Hot
A
E
Step 4: Connect waterlines
to main valve
Cold
E
6
Hot
6
E
Cold
E
A
Hot
Thread hot & cold waterlines (E)
onto angle stops. Tighten with
adjustable wrench until snug.
Turn onA the angle stops and
check for leaks (DO NOT TURN E
FAUCET ON)
Cold
E
Hot
A
6
6
6
Step 5: Connect quick connect
Remove spray head (A). Hold
tip of spray hose. Turn faucet
on for 1 minute to flush any
debris. Reconnect spray head
(A)
A
A
A
A
Replacement Part List
1. A Index Button
B Set Screw
2. Metal Handle
3. Cartridge Cover
4. Locking Nut
5. Cartridge
6
6. Clip
5
7
4
7. Set Screw
3
8
2
9
8. Spray Head
1
9. Base
10. Cover & Putty Plate
11. Hex Wrench 2.5mm
10
11
12
7
12. Hex Wrench 4mm
Hexagon Nut
9
11
12
Trouble - Shooting
13
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLEM
CAUSE
Water will not shut off
completely
Close
25˚
Hot
Water
Cold
Water
Cartridge(5) may need
to be adjusted or
replaced
Remove index button
(1A). Loosen set screw
(1B) with 2.5mm hex
wrench (13). Remove
metal handle (2).
Remove cartridge
cover (3) by hand only.
Remove locking nut
(4) with an adjustable
wrench. Remove ceramic
disc cartridge (5). Check
for cracks
Washer may be missing
or not seated correctly
in hose
Make sure washer is
Push
present and seated
correctly in hose
90˚
Leaking from between
spray head and hose
Open
ACTION
Left
Hot Water
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1.
2.
3.
4.
Rinse with clean water & dry with a soft cloth
Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
Do not use cloth with a coarse surface
Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
8
Codes/Standards Applicable:
GREEN
LEAD FREE
IA
P
NSF/ANSI 372
NSF/ANSI 61-9
MO
R
&T
Meets ASME A112.18.1M/A112.18.1
1.75gpm 6.6L/min maximum
TM
Water Efficiency
KRAUS LIMITED LIFETIME WARRANTY
This product has been manufactured and tested to the highest quality standards by
Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures & accessories, engineered for enduring performance over years of use.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is not transferable,
between homes or owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTY
Kraus warranties this product against defects due to material or craftsmanship error
during the warranty period: Kraus will provide replacement parts at no charge, or at
its option, replace any product or part of the product that is deemed defective, under
normal installation, use, service and maintenance. If Kraus is unable to provide a replacement and repair is not practical or cannot be made in timely fashion, Kraus may elect to
refund the purchase price in exchange for the return of the product.
CONDITIONS AND EXCLUSIONS
Like other home fixtures, Kraus products will require light maintenance to ensure proper
function. We provide you with complete knowledge to perform this maintenance and
can also recommend resources if you are unable to fulfill this service.
A. Kraus will not be responsible for product failures due to lack of maintenance or proper
use. Please read your care and maintenance documentation to determine the limits of
proper use.
B. The original sales receipt, order number, and/or proof of purchase must be presented
at the time of the warranty claim, without exception, for this warranty to be applied to all
Kraus products.
C. Kraus recommends installing all Kraus products with a licensed, professional plumber.
Kraus will not be held responsible for any damage or product failure due to improper
installation, misuse, or failure to use a licensed professional. Please read your care and
maintenance documentation to determine the limits of proper use.
D. Commercial use will automatically void this warranty.
E. This warranty is not applicable to Kraus products purchased from an unauthorized
seller. For a complete list of authorized sellers please visit http://www.kraususa.com/
where-to-buy.html
9
NON-APPLICABILITY OF THIS WARRANTY
By the purchase and use of our products, you agree that Kraus is not liable for incidental,
consequential or special damages associated with the return, replacement, installation or
use of your product. This includes freight costs, cartridge replacement, labor, travel time,
lost profit, home damages and other contingent liabilities and costs (including, without
limitation, costs associated with experts, investigations, analyses, attorneys and other
professionals and services). The Kraus warranty is a comprehensive and explicit limit of
liability, and all items outside of it are not addressable by or the responsibility of Kraus.
Certain states have variances regarding implied warranties and in those situations we
remain fully compliant.
KRAUS USA Inc. makes no implication that products comply with any or all local building
or plumbing codes. It is the consumer’s responsibility to determine local code
compliance. This warranty extends to the original purchaser and first consumer.
HELP LINE
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
Customerservice@kraususa.com
If you are a plumbing contractor or trade professional please contact a Kraus Pro
Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
Proservice@kraususa.com
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
Partnersupport@kraususa.com
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
10
www.kraususa.com
Download PDF
Similar pages