OWNERS MANUAL
MODEL:
CHILI/CHEESE WARMER
Steamer
PART NUMBER:
51072
120 volts, 60 hz
WARNING ELECTRICAL SHOCK HAZARD.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
WARNING: Handling the cord on this product may expose you to lead, a chemical known to the State Of California
to cause cancer and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.
1.
Electrical ground is required on this appliance.
2.
Do not modify the power supply cord plug. If it does not fit the outlet, have a proper outlet installed by a
qualified electrician.
3.
Do not use an extension cord with this appliance.
4.
Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded.
SAFETY INSTRUCTIONS
1.
2.
3
4.
5.
Plug electrical cord into a certified electrical outlet with a corresponding voltage rating as listed on the machine model
labels.
Always unplug the electric cord when appliance is not in use and before cleaning, adjusting or maintaining this
steamer. Do not operate with a damaged cord or plug or after the machine malfunctions, has been dropped or
damaged. Use authorized service for examination, electrical or mechanical adjustment or repair.
This equipment will be HOT during use and for a short time after it is turned off BE CAREFUL. To avoid burns, do
not let bare skin touch hot surfaces. If provided, use handles when moving this appliance. Keep combustible materials
away from appliance.
Extreme caution is necessary when any appliance is used by or near children and whenever the appliance is left
operating and unattended.
This appliance is not intended for use in wet locations. Never locate appliance where it may fall into a water container.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electrical shock,
fire or damage to the appliance.
CLEANING SAFETY INSTRUCTION
1.
2.
Turn control off and unplug the power cord. Avoid splashing water onto control.
Do not clean this appliance with a water jet or immerse in water or other liquid.
ASSEMBLY
Install the four legs into the threaded holes in the base.
2. Install the Adaptor plate on the warmer and insert the two round food pans in the openings. Put the lids
on the pans.
1.
OPERATING INSTRUCTIONS
1. Plug the machine into a properly grounded 120 volt power supply.
2. Fill the reservoir with 7 quarts of water by removing the Lids, pans and adaptor plate from the
machine and pouring water into the reservoir with a pitcher. Using hot water will speed up the startup time of the machine. Fill the reservoir with water to the MAX line which is marked in the
reservoir. The warmer will hold a maximum of 7 quarts.
3. Re-install the Adaptor Plate, pans and lids.
4. Put the desired amount in Chili and Cheese in the pans.
5. Turn on the “Master Switch” and set the thermostat to a maximum setting. The machine should be
producing steam in approximately 5-7 minutes (depending on water and room temperature). You
can adjust the thermostat according to your operating conditions.
6. Once Steam is produced adjust the thermostat to 80-100 to COOK and 60-80 to HOLD.
7. Once steam is produced food should reach serving temperature in approximately 20-30
minutes. Adjust the thermostat accordingly. You will want the food to maintain at least 140
Degrees Fahrenheit before serving.
8. CAUTION: Use serving utensils to remove food from the warmer as the product will be hot to the
touch.
9. IMPORTANT: DO NOT LET THE WATER LEVEL IN THE RESERVOIR GET BELOW THE
MINIMUM LINE. Letting the water run low or out could damage the unit and void your warranty.
The minimum line represents 4 quarts of water.
CONDENSATION
1. Cool air striking the warm steamer may cause moisture accumulation. Protecting the unit from cool
drafts of air will help prevent condensation.
2. As the covers of the warmer are opened and closed some of the condensation may leak out from
the under-sides of the lids. This should be wiped up with a towel or rag.
Page 2
CLEANING THE MACHINE
1. At the end of day: Turn the machine off using the master switch. Remove the lids, pans and adaptor
plate from the warmer. (caution: the items will be hot unless you wait long enough to allow them to
cool before removing!) These items can be taken to a sink or dishwasher for cleaning. Use a mild
detergent and water to clean.
2. Empty the remaining water in the reservoir by dumping it into a sink or drain. (caution: the water will
be hot unless you allow sufficient cool-down time). Clean the reservoir with a mild detergent and water.
Wipe down with a soft cloth.
3. Wipe down the outside of the unit with a mild detergent and a soft cloth.
4. After the components have been cleaned, re-assemble the machine as outlined above so you will
be ready for the next usage.
ASSEMBLY
(complete parts list on page 7)
Page 3
WIRING DIAGRAM
ELECTRICAL SPECIFICATIONS
Volts: 120
Watts:
1200
Amps:
10.0
Hertz:
50/60
Page 4
ASSEMBLY
PARTS LIST
Item
1
2
3
4
6
7
8
10
11
12
13
14
15
17
18
26
27
28
29
30
31
32
33
34
35
37
38
40
41
42
43
44
45
P/N
6701
6702
6703
6704
6706
6707
6708
6710
6711
6712
6713
6714
6715
6717
6718
6726
6727
6728
6729
6730
6731
6732
6733
6734
6735
6737
6738
6740
6741
6742
6753
6754
6755
Description
Reservoir
Warmer Body
Front Plate
Sheet Metal Screw
Leg
Element Spacer
Acorn Nut
Spacer tube
Threaded Rod
Bottom Aluminum Cover
Jumper
Terminal
Terminal Screw
Lock-washer
Bolt
Heating Element
Heat plate
Hold-down plate
Bracket
Element Lead
Switch Cover
Switch
Plug
Strain Relief
LED Light
Thermostat
Thermostat knob
Thermostat backer Plate
Bolt
Clamp
Adaptor Plate
Round 7 quart pan
Round lid
●
To Order Parts Contact:
●
HTD Canada
174 Colonnade Rd. S. # 33
Ottawa, Ontario, Canada, K2E7J5
Tel: 613-693-1806
Email: info@htdcanada.ca
Page 7
Three Year Warranty
THE WARRANTY:
Benchmark USA warrants the original purchaser of new food equipment manufactured by
Benchmark USA to be free from defects in material or workmanship from the date of the
original purchase for a period of three years.
WHO IS COVERED BY THIS WARRANTY:
The original purchaser who has provided proper proof of the original retail purchase and all
other requested information.
WHAT IS WARRANTIED:
The obligation of Benchmark USA under this warranty is limited to the replacement of any
parts or components that in the opinion of Benchmark USA are defective, F.O.B. the factory, or
at any other location that Benchmark USA may designate.
WHAT VOIDS THE WARRANTY:
1. Any piece of equipment that has been installed, operated or maintained inconsistently
with Benchmark USA operating instructions.
2. Any part or component that has been modified, changed or altered from its original
configuration.
3. Any electrical component that has been damaged due to submergence in any liquid.
4. Any part or component that has been subject to abuse, misuse, neglect or accidents.
EXTENT OF WARRANTY:
Any defective component, part or assembly returned to Benchmark USA will be replaced by
Benchmark USA. Benchmark USA will not be responsible for any expenses incurred by the
customer under the terms of this warranty, nor shall it be responsible for any damages either
consequential, special, contingent, or otherwise; or expenses or injury arising directly or
indirectly from the use of a Benchmark USA product. Any component, part or assembly
returned to Benchmark USA must be returned at the customers expense along with proof of
purchase. Benchmark USA reserves the right to determine whether the terms of this warranty
have been properly complied with. In the event that the terms are not complied with,
Benchmark USA shall be under no obligation to honor this warranty.
Canadian Residents ● HTD Canada ● 174 Colonnade RD. S #33 ● Ottawa, ON K2E7J5 ● T: 613-693-1806
Website: https://www.htdcanada.ca
Download PDF
Similar pages