Single Wall Faucet Product Installation Guide Replacement Parts for

Replacement Parts for Single Wall Faucets
fisher manufacturing company
Single Wall Faucet
Product Installation Guide
3967
16” SWING SPOUT
3964
14” SWING SPOUT
3700
CONTROL VALVE
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install the best.
Our hardware is manufactured with the standardization
of internal mechanisms. All chrome plating is triple
plated copper, nickel and chrome for durability. Every
piece of equipment we make is rigorously tested in
both our modern in-house testing center and in actual
field situations under extreme conditions. Every detail
is thoroughly checked. Before we make our products
available to you, they pass each and every test. You get
proven performance. Guaranteed.
3963
12” SWING SPOUT
2000-7500
SCREW
3962
10” SWING SPOUT
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
3961
8” SWING SPOUT
3960
6” SWING SPOUT
2000-2301
LEVER HANDLE
15621
SPOUT NUT
2000-3002
BIBB CAP
10464
DUCK GASKET
Limited One Year Warranty
3000-0000
RH SWIVEL STEM
REPAIR KIT
12564
2.2 GPM
AERATOR
2000-5000
WASHER
1000-7502
SCREW
10456
LUBE
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge to
you, provided that the entire product is delivered to
Fisher Manufacturing Company. All transportation and
insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external finish (except at
date of original purchase) or labor costs not specifically
authorized by Fisher Manufacturing Company.
1600-5000
SPOUT
O-RINGS
10456
LUBE
3000-0011
RH SWIVEL STEM
2000-5003
SEAT WASHER
2002
SNAP RING
10014 (24”)
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
19119
SWIVEL SPOUT
RETRO-FIT KIT
10049 (24”)
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
2400-2103
ELBOWS
1790-1
ANGLE STOP
W/ CROSS
HANDLE
3000-0003
DOUBLE JOINT
SPOUT 7 1/4”
OR
4000-0002
DOUBLE JOINT
SPOUT 13”
#3710 - Single Wall Faucet with 6” Swing Spout
#3711 - Single Wall Faucet with 8” Swing Spout
#3712 - Single Wall Faucet with 10” Swing Spout
#3713 - Single Wall Faucet with 12” Swing Spout
#3714 - Single Wall Faucet with 14” Swing Spout
#1805 - Single Wall Faucet with 16” Swing Spout
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
2200-0000
NIPPLE KIT
1792
ANGLE STOP
WITH KEY
KEEP THIS MANUAL FOR FUTURE REFERENCE
ANSI/A112.18.1M, ANSI/NSF 61.9
PART NO. 39497
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
REV. A
www.fisher-mfg.com
Installation Instructions for Single Wall Faucets
Installation Instructions Continued
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Notes:
Step 2
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.
Double Joint Spout
Tools Required for Installation
• Medium Sized Crescent Wrench
• Pipe Thread Sealant
Apply O-Ring
Lube Here
PST
Package Contents
The box should contain the following:
Control Valve
Qty: 1
Swing Spout
Length determined by model
Qty: 1
Each spout includes one 2002 snap ring
and two 1600-5000 o-rings
10456
Lube
Step 3
Swing Spout
Installation Instructions
1. Mount control valve body to either a wall with male supply nipples or a backsplash with nipples
(not included). Be sure to use pipe thread sealant on the nipple threads.
Apply O-Ring
Lube Here
2. If installing a double joint spout, apply lube to the o-rings on the spout. Mount the double joint
spout and tighten the nut onto the faucet spout outlet.
3. Apply lube to the o-rings on the swing spout. Make sure the white snap ring is in place before
mounting the swing spout. Mount the swing spout and tighten the swing spout nut onto the
faucet spout outlet.
4. Turn on water supply and check for leaks.
Step 1
Step 4
1/2” NPT Supply Nipples
(not included)
1/2” Supply Line
(Optional)
1/2” Nipple
(Optional)
1/2” Elbows
(Optional)
Ø7/8”
Download PDF
Similar pages