Washing Machine
User Manual
EV 7102
EN
Document Number= 2820524450 / 14-10-15.(16:19)
1 Important instructions for safety and environment
This section contains safety instructions that will help protect from risk of personal
injury or property damage. Failure to follow these instructions shall void any warranty.
1.1 General safety
•This product can be used by children at and above 8 years old and by persons
whose physical, sensory or mental capabilities were not fully developed or who
lack experience and knowledge provided that they are supervised or trained on
the safe usage of the product and the risks it brings out. Children must not play
with the product. Cleaning and maintenance works should not be performed by
children unless they are supervised by someone. Children of less than 3 years
should be kept away unless continuously supervised.
•Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems
with your product.
•If the product has a failure, it should not be operated unless it is repaired by the
Authorized Service Agent. There is the risk of electric shock!
•This product is designed to resume operating in the event of powering on after a
power interruption. If you wish to cancel the programme, see "Cancelling the programme" section.
•Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect
to have the grounding installation made by a qualified electrician. Our company
shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.
•The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.
•Never open the loading door or remove the filter while there is still water in the
drum. Otherwise, risk of flooding and injury from hot water will occur.
•Do not force open the locked loading door. The loading door will be ready to open
just a few minutes after the washing cycle comes to an end. In case of forcing the
loading door to open, the door and the lock mechanism may get damaged.
•Unplug the product when not in use.
•Never wash the product by spreading or pouring water onto it! There is the risk of
electric shock!
•Never touch the plug with wet hands! Never unplug by pulling on the cable, always
pull out by grabbing the plug.
This product was manufactured using the latest technology in environmentally friendly conditions.
•Use detergents, softeners and supplements suitable for automatic washing machines only.
•Follow the instructions on the textile tags and on the detergent package.
•The product must be unplugged during installation, maintenance, cleaning and
repairing procedures.
•Always have the installation and repairing procedures carried out by the
Authorized Service Agent. Manufacturer shall not be held liable for damages that
may arise from procedures carried out by unauthorized persons.
•If the power cable is damaged, it must be replaced by the manufacturer, after
sales service or a similarly qualified person (preferably an electrician) or someone
designated by the importer in order to avoid possible risks.
•Place the product on a rigid, flat and level surface.
•Do not place it on a long-pile rug or similar surfaces.
•Do not place the product on a high platform or near the edge on a cascaded surface.
•Do not place the product on the power cable.
•Never use sponge or scrub materials. These will damage the painted, chrome plated and plastic surfaces.
1.2 Intended use
•This product has been designed for domestic use. It is not suitable for commercial
use and it must not be used out of its intended use.
•The product must only be used for washing and rinsing of laundry that are marked
accordingly.
•The manufacturer waives any responsibility arisen from incorrect usage or transportation.
1.3 Children's safety
•Packaging materials are dangerous to children. Keep packaging materials in a safe
place away from reach of the children.
•Electrical products are dangerous for the children. Keep children away from the
product when it is in use. Do not let them to tamper with the product. Use child
lock to prevent children from intervening with the product.
•Do not forget to close the loading door when leaving the room where the product
is located.
•Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package.
While washing the laundry at high temperatures, the loading door
glass becomes hot. Therefore, keep especially the children away
from the loading door of the machine while the washing operation
is in progress.
3 / EN
Washing Machine / User’s Manual
1.4 Package information
•Packaging materials of the product are manufactured from recyclable materials
in accordance with our National Environment Regulations. Do not dispose of the
packaging materials together with the domestic or other wastes. Take them to
the packaging material collection points designated by the local authorities.
1.5 Disposing of the waste product
•This product has been manufactured with high quality parts and materials which
can be reused and are suitable for recycling. Therefore, do not dispose the product
with normal domestic waste at the end of its service life. Take it to a collection
point for the recycling of electrical and electronic equipment. Please consult your
local authorities to learn the nearest collection point. Help protect the environment and natural resources by recycling used products. For children's safety, cut
the power cable and break the locking mechanism of the loading door so that it
will be non-functional before disposing of the product.
1.6 Compliance with WEEE Directive
This product complies with EU WEEE Directive (2012/19/EU). This product
bears a classification symbol for waste electrical and electronic equipment
(WEEE).
This product has been manufactured with high quality parts and materials
which can be reused and are suitable for recycling. Do not dispose of the
waste product with normal domestic and other wastes at the end of its
service life. Take it to the collection center for the recycling of electrical
and electronic equipment. Please consult your local authorities to learn
about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It
does not contain harmful and prohibited materials specified in the Directive.
4 / EN
Washing Machine / User’s Manual
2Installation
Refer to the nearest Authorised Service Agent
for installation of the product. To make the
product ready for use, review the information
in the user manual and make sure that
the electricity, tap water supply and water
drainage systems are appropriate before
calling the Authorized Service Agent. If they
are not, call a qualified technician and plumber
to have any necessary arrangements carried
out.
C
InformatIons
Preparation of the location and electrical,
tap water and waste water installations at
the place of installation is under customer’s
responsibility.
Make sure that the water inlet and discharge
hoses as well as the power cable are not
folded, pinched or crushed while pushing
the product into its place after installation or
cleaning procedures.
product on a solid and flat floor that has
sufficient load carrying capacity!
• Do not place the product on the power
cable.
• Do not install the product at places
where temperature may fall below 0ºC.
• Place the product at least 1 cm away
from the edges of other furniture.
2.2 Removing packaging
reinforcement
Tilt the machine backwards to remove
the packaging reinforcement. Remove the
packaging reinforcement by pulling the ribbon.
B
warning
Installation and electrical connections of
the product must be carried out by the
Authorized Service Agent. Manufacturer
shall not be held liable for damages that
may arise from procedures carried out by
unauthorized persons.
A
warning
Prior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products cause
risks for your safety.
2.1 Appropriate installation location
• Place the machine on a rigid floor. Do
not place it on a long pile rug or similar
surfaces.
• Total weight of the washing machine
and the dryer -with full load- when they
are placed on top of each other reaches
to approx. 180 kilograms. Place the
5 / EN
Washing Machine / User’s Manual
2.3 Removing the transportation locks
A
warning
Do not remove the transportation
locks before taking out the packaging
reinforcement.
Remove the transportation safety bolts
before operating the washing machine!
Otherwise, the product will be damaged.
Loosen all the bolts with a suitable spanner
until they rotate freely (C). Remove
transportation safety bolts by turning them
gently. Attach the plastic covers supplied in
the User Manual bag into the holes on the rear
panel. (P)
C
InformatIons
Keep the transportation safety bolts in a safe
place to reuse when the washing machine
needs to be moved again in the future.
Never move the product without the
transportation safety bolts properly fixed in
place!
2.4 Connecting water supply
C
InformatIons
The water supply pressure required to run
the product is between 1 to 10 bars (0.1 – 1
MPa). It is necessary to have 10 – 80 liters of
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
If you are going to use the double waterinlet product as a single (cold) water-inlet
unit, you must install the supplied stopper
to the hot water valve before operating the
product. (Applies for the products supplied
with a blind stopper group.)
If you want to use both water inlets of the
product, connect the hot water hose after
removing the stopper and gasket group
from the hot water valve. (Applies for the
products supplied with a blind stopper
group.)
A
warning
Models with a single water inlet should not
be connected to the hot water tap. In such
a case the laundry will get damaged or the
product will switch to protection mode and
will not operate.
Do not use old or used water inlet hoses on
the new product. It may cause stains on your
laundry.
Connect the special hoses supplied with the
product to the water inlets on the product. Red
hose (left) (max. 90 ºC) is for hot water inlet,
blue hose (right) (max. 25 ºC) is for cold water
inlet.
A
warning
Ensure that the cold and hot water
connections are made correctly when
installing the product. Otherwise, your
laundry will come out hot at the end of the
washing process and wear out.
Tighten all hose nuts by hand. Never use
a wrench when tightening the nuts. Open
the taps completely after making the hose
6 / EN
Washing Machine / User’s Manual
connection to check for water leaks at the
connection points. If any leaks occur, turn off
the tap and remove the nut. Retighten the nut
carefully after checking the seal. To prevent
water leakages and damages caused by them,
keep the taps closed when the machine is not
in use.
2.5 Connecting to the drain
• The end of the drain hose must be
directly connected to the wastewater
drain or to the washbasin.
A
• The end of the hose should not be bent,
it should not be stepped on and the
hose must not be pinched between the
drain and the machine.
• If the length of the hose is too short, use
it by adding an original extension hose.
Length of the hose may not be longer
than 3.2 m. To avoid water leak failures,
the connection between the extension
hose and the drain hose of the product
must be fitted well with an appropriate
clamp as not to come off and leak.
2.6 Adjusting the feet
warning
Do not remove the transportation
locks before taking out the packaging
reinforcement.
A
warning
Loosen the lock nuts on the feet by hand.
Adjust the feet until the product stands level
and balanced. Tighten all lock nuts again by
hand.
40cm
100cm
• The hose should be attached to a height
of at least 40 cm, and 100 cm at most.
• In case the hose is elevated after
laying it on the floor level or close to
the ground (less than 40 cm above the
ground), water discharge becomes more
difficult and the laundry may come out
excessively wet. Therefore, follow the
heights described in the figure.
In order to ensure that the product operates
more silently and vibration-free, it must
stand level and balanced on its feet.
Balance the machine by adjusting the feet.
Otherwise, the product may move from
its place and cause crushing and vibration
problems.
• To prevent flowing of dirty water back
into the machine and to allow for easy
discharge, do not immerse the hose end
into the dirty water or do not drive it in
the drain more than 15 cm. If it is too
long, cut it short.
7 / EN
A
warning
Do not use any tools to loosen the lock nuts.
Otherwise, they will get damaged.
Washing Machine / User’s Manual
2.7 Electrical connection
Connect the product to a grounded outlet
protected by a fuse complying with the values
in the "Technical specifications" table. Our
company shall not be liable for any damages
that will arise when the product is used
without grounding in accordance with the local
regulations.
• Connection must comply with national
regulations.
• Power cable plug must be within easy
reach after installation.
• The voltage and allowed fuse or breaker
protection are specified in the “Technical
specifications” section. If the current
value of the fuse or breaker in the house
is less than 16 Amps, have a qualified
electrician install a 16 Amp fuse.
• The specified voltage must be equal to
your mains voltage.
• Do not make connections via extension
cables or multi-plugs.
B
warning
Damaged power cables must be replaced by
the Authorized Service Agents.
2.8 First use
Before starting to use the product, make sure
that all preparations are made in accordance
with the instructions in sections "Important
safety instructions" and "Installation".
To prepare the product for washing laundry,
perform first operation in Cotton-90
programme. Before starting the programme,
put max. 100 g of powder anti-limescale
into the main wash detergent compartment
(compartment nr. II). If the anti-limescale
is in tablet form, put only one tablet into
compartment nr. II. Dry the inside of the
bellow with a clean piece of cloth after the
programme has come to an end.
8 / EN
C
InformatIons
Use an anti-limescale suitable for the
washing machines.
Some water might have remained in the
product due to the quality control processes
in the production. It is not harmful for the
product.
2.9 Disposing of packaging material
Packaging materials are dangerous to children.
Keep packaging materials in a safe place away
from reach of the children.
Packaging materials of the product are
manufactured from recyclable materials.
Dispose of them properly and sort in
accordance with recycled waste instructions.
Do not dispose of them with normal domestic
waste.
2.10 Transportation of the product
Unplug the product before transporting
it. Remove water drain and water supply
connections. Drain the remaining water in the
product completely; see, "Draining remaining
water and cleaning the pump filter". Install
transportation safety bolts in the reverse
order of removal procedure; see, "Removing
the transportation locks".
C
InformatIons
Never move the product without the
transportation safety bolts properly fixed in
place!
2.11 Disposing of the old product
Dispose of the old product in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how to
dispose of your product.
For children's safety, cut the power cable and
break the locking mechanism of the loading
door so that it will be nonfunctional before
disposing of the product.
Washing Machine / User’s Manual
3Preparation
• Put small size clothes such as infant's
socks and nylon stockings in a laundry
3.1 Things to be done for energy
bag or pillow case.
saving
• Place curtains in without compressing
Following information will help you use the
them. Remove curtain attachment
product in an ecological and energy-efficient
items.
manner.
•
Fasten
zippers, sew loose buttons and
• Operate the product in the highest
mend
rips
and tears.
capacity allowed by the programme you
•
Wash
“machine
washable” or “hand
have selected, but do not overload; see,
washable” labeled products only with an
"Programme and consumption table".
appropriate programme.
• Always follow the instructions on the
•
Do
not wash colours and whites
detergent packaging.
together.
New, dark coloured cottons
• Wash slightly soiled laundry at low
release a lot of dye. Wash them
temperatures.
separately.
• Use faster programmes for small
•
Tough
stains must be treated properly
quantities of lightly soiled laundry.
before
washing. If unsure, check with a
• Do not use high temperatures for
dry cleaner.
laundry that is not heavily soiled or
•
Use
only dyes/colour changers and
stained.
limescale
removers suitable for machine
• Do not use detergent in excess of the
wash.
Always
follow the instructions on
amount recommended on the detergent
the package.
package.
• Wash trousers and delicate laundry
3.2 Sorting the laundry
turned inside out.
• Sort laundry according to type of
• Keep laundry items made of Angora
fabric, colour, and degree of soiling and
wool in the freezer for a few hours
allowable water temperature.
before washing. This will reduce pilling.
• Always obey the instructions given on
• Laundry that are subjected to materials
the garment tags.
such as flour, lime dust, milk powder,
etc. intensely must be shaken off before
3.3 Preparing laundry for washing
placing into the machine. Such dusts
• Laundry items with metal attachments
and powders on the laundry may build
such as, underwired bras, belt buckles or
up on the inner parts of the machine in
metal buttons will damage the machine.
time and can cause damage.
Remove the metal pieces or wash the
clothes by putting them in a laundry bag
or pillow case.
• Take out all substances in the pockets
such as coins, pens and paper clips, and
turn pockets inside out and brush. Such
objects may damage the product or
cause noise problem.
9 / EN
Washing Machine / User’s Manual
3.4 Correct load capacity
The maximum load capacity depends on the
type of laundry, the degree of soiling and the
washing programme desired.
The machine automatically adjusts the
amount of water according to the weight of
the loaded laundry.
A
warning
Follow the information in the “Programme
and consumption table”. When overloaded,
machine’s washing performance will drop.
Moreover, noise and vibration problems may
occur.
3.6 Using detergent and softener
Detergent Drawer
The detergent drawer is composed of three
compartments:
- (1) for prewash
- (2) for main wash
– (3) for softener
– (*) in addition, there is siphon piece in the
softener compartment.
2 3
1
Laundry types and their average weights in
the following table are given as examples.
Laundry type
Weight (g)
Bathrobe
1200
Duvet cover
700
Bed Sheet
500
Pillowcase
200
Tablecloth
250
Towel
200
Men’s shirt
200
3.5 Loading the laundry
Open the loading door. Place laundry items
loosely into the machine. Push the loading
door to close until you hear a locking sound.
Ensure that no items are caught in the door.
C
InformatIons
The loading door is locked while a
programme is running. The door can only be
opened a while after the programme comes
to an end.
A
warning
In case of misplacing the laundry, noise and
vibration problems may occur in the machine.
10 / EN
Detergent, softener and other cleaning agents
• Add detergent and softener before
starting the washing programme.
• Never open the detergent drawer while
the washing programme is running!
• When using a programme without
prewash, do not put any detergent
into the prewash compartment
(compartment nr. 1).
• In a programme with prewash, do not
put liquid detergent into the prewash
compartment (compartment nr. 1).
• Do not select a programme with
prewash if you are using a detergent bag
or dispensing ball. Place the detergent
bag or the dispensing ball directly
among the laundry in the machine.
Washing Machine / User’s Manual
• If you are using liquid detergent, do
not forget to place the liquid detergent
cup into the main wash compartment
(compartment nr. 2).
3.7 Choosing the detergent type
The type of detergent to be used depends on
the type and colour of the fabric.
• Use different detergents for coloured
and white laundry.
• Wash your delicate clothes only with
special detergents (liquid detergent,
wool shampoo, etc.) used solely for
delicate clothes.
• When washing dark coloured clothes
and quilts, it is recommended to use
liquid detergent.
• Wash woolens with special detergent
made specifically for woolens.
3.9 Using softeners
Pour the softener into the softener
compartment of the detergent drawer.
• Use the dosages recommended on the
package.
• Do not exceed the (>max<) level
marking in the softener compartment.
• If the softener has lost its fluidity, dilute
it with water before putting it in the
detergent drawer.
Using bleaches
• Select a programme with prewash
and add the bleaching agent at the
beginning of the prewash. Do not put
detergent in the prewash compartment.
• Do not use bleaching agent and
detergent by mixing them.
• Use just a little amount (approx. 50 ml)
of bleaching agent and rinse the clothes
very well as it causes skin irritation. Do
warning
not pour the bleaching agent onto the
Use only detergents manufactured
clothes and do not use it for coloured
specifically for automatic washing machines.
clothes.
Do not use soap powder.
• When using oxygen based bleaches,
follow the instructions on the package
3.8 Adjusting detergent amount
The amount of washing detergent to be
and select a programme that washes at
used depends on the amount of laundry, the
a lower temperature.
degree of soiling and water hardness. Read the • Oxygen based bleaches can be used
manufacturer's instructions on the detergent
together with detergents; however, if
package carefully and follow the dosage
its thickness is not the same with the
values.
detergent, put the detergent first into
• Do not use amounts exceeding the
the compartment nr. "II" in the detergent
dosage quantities recommended on the
drawer and wait until the detergent
detergent package to avoid problems of
flows while the machine is taking in
excessive foam, poor rinsing, financial
water. Add the bleaching agent from the
savings and finally, environmental
same compartment while the machine is
protection.
still taking in water.
• Use lesser detergent for small amounts Using limescale remover
or lightly soiled clothes.
• When required, use limescale removers
• Use concentrated detergents in the
manufactured specifically for washing
recommended dosage.
machines only.
A
• Always follow instructions on the
package.
11 / EN
Washing Machine / User’s Manual
3.10 Tips for efficient washing
Light colours and
whites
Delicates/
Woolens/Silks
(Recommended (Recommended
(Recommended
temperature
temperature
temperature range
range based
range based
based on soiling
on soiling level: on soiling level:
level: cold-40ºC)
cold-40ºC)
cold-30ºC)
Colours
Dark colours
It may be necessary
to pre-treat the
stains or perform
prewash. Powder
and liquid detergents
Heavily Soiled recommended
for whites can be
used at dosages
(difficult
stains such as recommended
grass, coffee, for heavily soiled
clothes. It is
fruits and
recommended to use
blood.)
powder detergents
to clean clay and soil
stains and the stains
that are sensitive to
bleaches.
Powder and
liquid detergents
recommended
for colours can be
used at dosages
recommended
for heavily soiled
clothes. It is
recommended
to use powder
detergents to clean
clay and soil stains
and the stains
that are sensitive
to bleaches. Use
detergents without
bleach.
Liquid
detergents
suitable for
colours and dark
colours can be
used at dosages
recommended
for heavily
soiled clothes.
Prefer liquid
detergents
produced for
delicate clothes.
Woolen and silk
clothes must be
washed with
special woolen
detergents.
Powder and
liquid detergents
recommended
(For example, for whites can be
stains caused used at dosages
recommended for
by body on
normally soiled
collars and
clothes.
cuffs)
Powder and
liquid detergents
recommended
for colours can be
used at dosages
recommended for
normally soiled
clothes. Use
detergents without
bleach.
Liquid
detergents
suitable for
colours and dark
colours can be
used at dosages
recommended
for normally
soiled clothes.
Prefer liquid
detergents
produced for
delicate clothes.
Woolen and silk
clothes must be
washed with
special woolen
detergents.
Powder and
liquid detergents
Lightly Soiled recommended
for whites can be
(No visible
used at dosages
stains exist.) recommended for
lightly soiled clothes.
Powder and
liquid detergents
recommended
for colours can be
used at dosages
recommended
for lightly soiled
clothes. Use
detergents without
bleach.
Liquid
detergents
suitable for
colours and dark
colours can be
used at dosages
recommended
for lightly soiled
clothes.
Prefer liquid
detergents
produced for
delicate clothes.
Woolen and silk
clothes must be
washed with
special woolen
detergents.
(Recommended
temperature range
based on soiling
level: 40-90ºC)
Soiling Level
Clothes
Normally
Soiled
12 / EN
Washing Machine / User’s Manual
4Operating the product
4.1 Control panel
1
2
3
4
5
1 - Programme Selection knob (Uppermost position On / Off)
2 - Door open indicator
3 - Programme Follow-up indicator
4 - Start / Pause button
5- Spin Speed Adjustment button
13 / EN
Washing Machine / User’s Manual
4.2 Preparing the machine
Make sure that the hoses are connected
tightly. Plug in your machine. Turn the tap on
completely. Place the laundry in the machine. Add detergent and fabric softener.
Programme selection
Select the programme suitable for the type,
quantity and soiling degree of the laundry
in accordance with the "Programme and
consumption table" and the temperature table
below. Select the desired programme with the
Programme Selection button.
Heavily soiled white cottons
and linens. (coffee table covers,
tableclothes, towels, bed sheets,
etc.)
Normally soiled, coloured, fade
proof linens, cottons or synthetic
clothes (shirt, nightgown, pajamas,
etc.) and lightly soiled white linens
(underwear, etc.)
Blended laundry including
delicate textile (veil curtains, etc.),
synthetics and woolens.
90˚C
60˚C
40˚C30˚CCold
C
InformatIons
Use an anti-limesc Programmes are limited
with the highest spin speed appropriate for
that particular type of fabric. ale suitable for
the washing machines.
When selecting a programme, always
consider the type of fabric, colour, degree of
soiling and permissible water temperature.
For further programme details, see
“Programme and consumption table”.
4.3 Main programmes
Depending on the type of fabric, use the
following main programmes.
• Cottons
Use this programme for your cotton laundry
(such as bed sheets, duvet and pillowcase
sets, towels, bathrobes, underwear, etc.). Your
laundry will be washed with vigorous washing
action for a longer washing cycle.
• Synthetics
Use this programme to wash your synthetic
clothes (shirts, blouses, synthetic/cotton
blends, etc.). It washes with a gentle action
and has a shorter washing cycle compared to
the Cotton programme.
For curtains and tulle, use the Synthetic 40˚C
programme. As their meshed texture causes
excessive foaming, wash the veils/tulle by
putting little amount of detergent into the
main wash compartment. Do not put detergent
in the prewash compartment.
• Woollens 40°
Use this programme to wash your woolen
clothes. Select the appropriate temperature
complying with the tags of your clothes. Use
appropriate detergents for woolens.
4.4 Additional programmes
For special cases, additional programmes are
available in the machine.
C
InformatIons
Additional programmes may differ according
to the model of the machine.
• Cottons Eco
Use this programme to wash your laundry
washable in cottons programme for a longer
time, still with a very good performance for
saving purposes.
C
InformatIons
Cottons Eco programme consumes
less energy compared to other cottons
programmes.
14 / EN
Washing Machine / User’s Manual
• Delicates 30°
Use this programme to wash your delicate
clothes. It washes with a gentle action without
any interim spin compared to the Synthetics
programme.
• Hand Wash 20°
Use this programme to wash your woolen/
delicate clothes that bear “not machinewashable” tags and for which hand wash
is recommended. It washes laundry with a
very gentle washing action to not to damage
clothes.
• Mini 30
Use this programme to wash your lightly soiled
cotton clothes in a short time.
• Cottons 60º with Prewash
Prefer this programme only for heavily soiled
cotton clothes.
4.5 Special programmes
For specific applications, select any of the
following programmes.
• Rinse
Use this programme when you want to rinse or
starch separately.
• Spin+Drain
Use this programme to apply an additional spin
cycle for your laundry or to drain the water in
the machine.
C
InformatIons
4.6 Spin speed selection
Whenever a new programme is selected, the
recommended spin speed of the selected
program is displayed on the spin speed
indicator.
To decrease the spin speed, press the
spin speed adjustment button. Spin speed
decreases gradually.
Then, depending on the model of the product,
“Rinse Hold” and “No Spin” options appear on
the spin speed led indicator.
4.7 Rinse Hold
If you are not going to unload your clothes
immediately after the programme completes,
you may use rinse hold function to keep your
laundry in the final rinsing water in order to
prevent them from getting wrinkled when
there is no water in the machine.
In rinse hold step, the machine will be in pause
mode and “start/pause” led will be blinking.
In rinse hold step, if you want to drain the
water without spinning your laundry, press the
“start/pause” button. Programme will resume
and complete after draining the water.
If you want to spin the laundry held in water,
select the spin speed and press “start/pause
button. The programme resumes, water is
drained, laundry is spun and the programme is
completed.
If you wish to drain the water only without
spinning your laundry, select the Spin+Pump
programme and press “Start / Pause” button.
Machine will switch to spin step once it
completes the program step. Press “Start /
Pause” button to stop the machine as soon
as you see the drum rotating. And cancel this
programme by turning Programme Selection
knob to any other position.
15 / EN
Washing Machine / User’s Manual
4.8 Programme and consumption table
Programme Duration (~min)
Water Consumption (l)
Energy Consumption (kWh)
Max. Speed***
2
Max. Load (kg)
EN
60
7
121
66
1.65
1400
90
7
133
55
2.10
1400
40
7
80
55
0.66
1400
Programme
Cottons 60º with Prewash
Cottons
Cottons Eco
Synthetics
Cold
7
80
55
0.15
1400
60**
7
132
52
1.14
1400
40
3.5
120
46
0.72
1400
60
2.5
113
65
1.10
800
40
2.5
105
65
0.58
800
Cold
2.5
66
65
0.11
800
Delicates 30°
30
2
65
48
0.32
800
Woollens 40°
40
1.5
54
52
0.40
800
Hand Wash 20°
20
1
41
35
0.20
800
Mini 30
30
2.5
29
72
0.21
1400
• : Selectable
** : Energy Label programme (EN 60456)
***:If maximum spin speed of the machine is lower then this value, you can only select
up to the maximum spin speed.
C
InformatIons
Water and power consumption may vary subject to the changes in water pressure, water
hardness and temperature, ambient temperature, type and amount of laundry, selection of
auxiliary functions and spin speed, and changes in electric voltage.
C
InformatIons
Cottons Eco 60C is recommended programme for normally soiled clothes.
16 / EN
Washing Machine / User’s Manual
4.9 Starting the programme
Press Start / Pause button to start the
programme. Programme follow-up light
showing the startup of the programme will
turn on.
Progress of programme
Progress of a running programme can be
followed from the Programme Follow-up
indicator with the lights "Running" and "End/
Cancel".
C
InformatIons
If the machine does not pass to the spinning
step, automatic unbalanced load detection
system might have been activated due to the
unbalanced distribution of the laundry in the
machine.
4.10 Loading door lock
There is a locking system on the loading
door of the machine that prevents opening
of the door in cases when the water level is
unsuitable.
If you want to open loading door when the
machine is in use, press "Start / Pause" button
to pause the machine. "Door Open" light will
start flashing when the machine is switched
to Pause mode. Machine checks the level of
the water inside. If the level is suitable, "Door
Open" light illuminates steadily within 1-2
minutes and the loading door can be opened.
If the level is unsuitable, "Door Open" light
turns off and the loading door cannot be
opened. If you are obliged to open the loading
door when the "Door Open" light is off, you
have to cancel the current programme; see
"Cancelling the programme".
Switching the machine to pause mode
Press the "Start / Pause" button to switch the
machine to pause mode while a programme is
running. "Running" light starts flashing on the
Programme Follow-up indicator to show that
the machine has been switched to the pause
mode.
When the loading door is ready to be opened,
"Door Open" light will illuminate continuously.
17 / EN
Adding or taking out laundry
Press "Start / Pause" button to switch the
machine to pause mode. When the machine
is switched to pause mode, "Running" light
flashes. Wait until the Loading Door can be
opened. Open the Loading Door and add or
take out the laundry.
Close the Loading Door. Press "Start / Pause"
button to start the machine.
C
InformatIons
The door can be opened if the water level
is suitable. Door open symbol flashes until
the loading door gets ready to be opened.
The symbol’s light is steady when the door is
ready to open. You can open the door to add/
take out laundry.
4.11 Cancelling the programme
To cancel the programme, turn the Programme
Selection knob to select another programme.
Previous programme will be cancelled. "End/
Cancel" light will flash continuously to notify
that the programme has been cancelled.
C
InformatIons
If you start a new programme after
cancelling the previous one, this new
programme will start without draining the
water in the machine.
If you must certainly open the loading
door when the “Door Open” light is off, you
need to use “Spin+Pump” programme. See
“Spin+Pump”
Re-spinning the laundry
Unbalanced load control system can prevent
spinning because of unbalanced load of
laundry in the machine. If you would like to
spin again:
Rearrange the laundry in the machine. Select
Spin+Pump programme and press “Start /
Pause" button. Washing Machine / User’s Manual
4.12 End of programme
"End/Cancel" light on the programme followup indicator will light up once the programme
comes to an end; and "Door Open" symbol
flashes for 1-2 minutes until the door is ready
to open. When "Door Open" symbol is steadily
illuminated, the door can be opened.
To turn off the machine, turn program
selection knob to "On / Off" position. Take out
your laundry and close the loading door. The
machine will be ready for the next run.
5
Maintenance and cleaning
Service life of the product extends and
frequently faced problems decrease if cleaned
at regular intervals.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals
(every 4-5 washing cycles) as shown below
in order to prevent accumulation of powder
detergent in time.
4.13 Door Open
"Door Open" symbol is illuminated when the
door is ready to open. It flashes until the door
gets ready to open. If the "Door Open" symbol
is not illuminated, do not force the door to
open. The symbol's light is steady when the
door is ready to open.
4.14 Your machine is equipped with a
“Standby Mode”
In case of not starting any programme or
waiting without making any other operation
when the machine is turned on by On/Off
button and while it is in selection step or if no
other operation is performed approximately
2 minutes after the programme you selected
has come to an end, your machine will
automatically switch to energy saving mode.
Brightness of indicator lights will decrease.
Also, if your product is equipped with a display
showing the programme duration, this display
will completely turn off. In case of rotating the
Programme Selection knob or pressing any
button, lights and display will restore to their
previous condition. Your selections made while
exiting the energy saving mode may change.
Check the appropriateness of your selections
before starting the programme. Readjust if
necessary. This is not a fault.
18 / EN
Press the dotted point on the siphon in the
softener compartment and pull towards you
until the compartment is removed from the
machine.
C
InformatIons
If more than normal amount of water and
softener mixture starts to gather in the
softener compartment, the siphon must be
cleaned.
Wash the detergent drawer and the siphon
with plenty of lukewarm water in a washbasin.
Wear protective gloves or use an appropriate
brush to avoid touching of the residues in the
drawer with your skin when cleaning. Insert
the drawer back into its place after cleaning
and make sure that it is seated well.
5.2 Cleaning the loading door and the
drum
For products with drum cleaning programme,
please see Operating the product Programmes.
For products without drum cleaning, follow the
below steps to clean the drum:
Select Additional Water or Extra Rinse auxiliary
functions. Use a Cottons programme without
Washing Machine / User’s Manual
pre-wash. Set the temperature to the level
recommended on the drum cleaning agent
which can be provided from authorized
services. Apply this procedure without any
laundry in the product. Before starting the
programme, put 1 pouch of special drum
cleaning agent (if the special agent could
not be supplied, put max. 100 g of powder
anti-limescale) into the main wash detergent
compartment (compartment no. “2”). If the
anti-limescale is in tablet form, put only one
tablet into the main wash compartment no. “2”.
Dry the inside of the bellow with a clean piece
of cloth after the programme has come to an
end.
C
InformatIons
Repeat Drum Cleaning process in every 2
months.
Use an anti-limescale suitable for the
washing machines.
5.3 Cleaning the body and control
panel
Wipe the body of the machine with soapy
water or non-corrosive mild gel detergents as
necessary, and dry with a soft cloth.
Use only a soft and damp cloth to clean the
control panel.
A
warning
Never use sponge or scrub materials. These
will damage the painted and plastic surfaces.
5.4 Cleaning the water intake filters
There is a filter at the end of each water intake
valve at the rear of the machine and also at
the end of each water intake hose where they
are connected to the tap. These filters prevent
foreign substances and dirt in the water to
enter the washing machine. Filters should be
cleaned as they do get dirty.
After every washing make sure that no foreign
substance is left in the drum.
If the holes on the bellow shown in the figure
is blocked, open the holes using a toothpick.
C
Close the taps. Remove the nuts of the water
intake hoses to access the filters on the water
intake valves. Clean them with an appropriate
brush. If the filters are too dirty, take them out
by means of pliers and clean them. Take out
the filters on the flat ends of the water intake
hoses together with the gaskets and clean
thoroughly under running water. Replace the
gaskets and filters carefully in their places and
tighten the hose nuts by hand.
InformatIons
Foreign metal substances will cause rust
stains in the drum. Clean the stains on the
drum surface by using cleaning agents for
stainless steel. Never use steel wool or wire
wool.
19 / EN
Washing Machine / User’s Manual
5.5 Draining remaining water and
cleaning the pump filter
The filter system in your machine prevents
solid items such as buttons, coins and fabric
fibers clogging the pump impeller during
discharge of washing water. Thus, the water
will be discharged without any problem and
the service life of the pump will extend.
If the machine fails to drain water, the pump
filter is clogged. Filter must be cleaned
whenever it is clogged or in every 3 months.
Water must be drained off first to clean the
pump filter.
In addition, prior to transporting the machine
(e.g., when moving to another house) and in
case of freezing of the water, water may have
to be drained completely.
A
warning
Foreign substances left in the pump filter
may damage your machine or may cause
noise problem.
Open the filter cover by pulling it from both
sides at the top.
C
InformatIons
You can remove the filter cover by slightly
pushing downwards with a thin plastic
tipped tool, through the gap above the
filter cover. Do not use metal tipped tools to
remove the cover.
Follow the steps below to discharge the water.
In order to clean the dirty filter and discharge
the water:
Unplug the machine to cut off the supply
power.
A
warning
Temperature of the water inside the
machine may rise up to 90 ºC. To avoid
burning risk, filter must be cleaned after the
water in the machine cools down.
20 / EN
Place a large container in front of the filter to
catch water from the filter. Loosen pump filter
(anticlockwise) until water starts to flow. Fill
the flowing water into the container you have
placed in front of the filter. Always keep a piece
of cloth handy to absorb any spilled water.
When the water inside the machine is finished,
take out the filter completely by turning it.
Clean any residues inside the filter as well as
fibers, if any, around the pump impeller region.
Install the filter.
Seat the tabs in the lower part into their places
first, and then press the upper part to close.
Washing Machine / User’s Manual
6Technical specifications
Supplier name or trademark
Model name
Rated capacity (kg)
Maximum spin speed (rpm)
Beko
EV 7102
7
1000
Height (cm)
84
Width (cm)
60
Depth (cm)
50
Net weight (±4 kg.)
61
Single Water inlet / Double Water inlet
• Available
Electrical input (V/Hz)
•/230 V / 50Hz
Total current (A)
10
Total power (W)
2200
Main model code
9410
21 / EN
Washing Machine / User’s Manual
7Troubleshooting
Program does not start after closing the door.
• Start / Pause / Cancel button was not pressed.>>> *Press the Start / Pause / Cancel
button.
Programme cannot be started or selected.
• Washing machine has switched to self protection mode due to a supply problem
(line voltage, water pressure, etc.). >>> To cancel the programme, turn the
Programme Selection knob to select another programme. Previous programme will
be cancelled. (See "Cancelling the programme")
Water in the machine.
• Some water might have remained in the product due to the quality control processes
in the production. >>> This is not a failure; water is not harmful to the machine.
Machine vibrates or makes noise.
• Machine might be standing unbalanced. >>> Adjust the feet to level the machine.
• A hard substance might have entered into the pump filter. >>> Clean the pump filter.
• Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.
• Laundry quantity in the machine might be too little. >>> Add more laundry to the
machine.
• Machine might be overloaded with laundry. >>> Take out some of the laundry from the
machine or distribute the load by hand to balance it homogenously in the machine.
• Machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on
anything.
Machine stopped shortly after the programme started.
• Machine might have stopped temporarily due to low voltage. >>> It will resume running
when the voltage restores to the normal level.
Programme time does not countdown. (On models with display)
• Timer may stop during water intake. >>> Timer indicator will not countdown until the
machine takes in adequate amount of water. The machine will wait until there is sufficient amount
of water to avoid poor washing results due to lack of water. Timer indicator will resume countdown
after this.
• Timer may stop during heating step. >>> Timer indicator will not countdown until the
machine reaches the selected temperature.
• Timer may stop during spinning step. >>> Automatic unbalanced load detection system
might be activated due to the unbalanced distribution of the laundry in the drum.
C
InformatIons
Machine does not switch to spinning step when the laundry is not evenly distributed in the
drum to prevent any damage to the machine and to its surrounding environment. Laundry
should be rearranged and re-spun.
22 / EN
Washing Machine / User’s Manual
Foam is overflowing from the detergent drawer.
• Too much detergent is used. >>> Mix 1 tablespoonful softener and ½ l water and pour into
the main wash compartment of the detergent drawer.
C
InformatIons
Put detergent into the machine suitable for the programmes and maximum loads indicated in
the “Programme and consumption table”. When you use additional chemicals (stain removers,
bleachs and etc), reduce the amount of detergent.
Laundry remains wet at the end of the programme
• Excessive foam might have occurred and automatic foam absorption system might
have been activated due to too much detergent usage. >>> Use recommended amount
of detergent.
C
InformatIons
Machine does not switch to spinning step when the laundry is not evenly distributed in the
drum to prevent any damage to the machine and to its surrounding environment. Laundry
should be rearranged and re-spun.
A
warning
If you cannot eliminate the problem although you follow the instructions in this section, consult
your dealer or the Authorized Service Agent. Never try to repair a nonfunctional product
yourself.
23 / EN
Washing Machine / User’s Manual
www.beko.com
Download PDF
Similar pages