DRAWING INDEX
VOLUME 1
VOLUME 2
SURVEY
SV-1
PROJECT INFORMATION
•
•
•
•
3/5/2018 8:46:23 AM
•
USE GROUP: A-3 LIBRARY
CONSTRUCTION TYPE: IIB
AUTOMATIC SPRINKLER SYSTEM : YES
AREA MODIFICATIONS PER SECTION 506
Automatic Sprinkler per 506.3: (Is=2)
Area Increase per 506 : Aa = {At +[AtxIf] + [AtxIs] = xxxx per story
Aa = ALLOWABLE BUILDING AREA PER STORY
At = TABULAR BUILDING AREA
If = AREA INCREASE FACTOR DUE TO FRONTAGE
TYPE IIB = = {At +[AtxIf] + [AtxIs]}
If=[F/P-0.25]w/30
If = [148 ft (open space)/586 ft (entire perimeter) -0.25] 30 (Width)/30 = 0.0025
If=0.0245
F=148, P= 586, W=30
=9500 + [9500 x (0.0025) + [9500x2)}
Aa= 28,524 sq ft per story
AREA 1ST FLOOR : 15,766 S.F.
AREA 2ND FLOOR: 14,739 S.F.
TOTAL AREA:
30,505 S.F.
TOPO & BOUNDARY SURVEY
CIVIL
C-1.0
C-2.0
C-3.0
C-4.0
C-5.0
C-6.0
C-7.0
C-7.1
C-8.0
PLAN-DEMO
PLAN-PROPOSED SITE
PLAN-SITE DIMENSIONAL
PLAN-SITE GRADING
PLAN-SITE UTILITY
PLAN-EROSION CONTROL
SITE DETAILS
UTILITY DETAILS
PLAN-TRAFFIC CONTROL
SITE UTILITY
UE-1.1 SITE ELECTRIC UTILITY PLAN
UE-4.1 SITE ELECTRIC DETAILS
FIRE PROTECTION
FP-0.1 FIRE PROTECTION LEAD SHEET
FP-1.1 FIRE PROTECTION FIRST FLOOR PLAN
FP-1.2 FIRE PROTECTION SECOND FLOOR PLAN
PLUMBING
STRUCTURAL
ABBREVIATIONS
A.C.T. ACOUSTIC CEILING TILE
A.E.S.S. - ARCHITECTURAL EXPOSED STRUCTRUAL STEEL
- ABOVE FINISH FLOOR
A.F.F.
ALUM.
- ALUMINUM
APPROX. - APPROXIMATE
BD.
- BOARD
BLDG.
- BUILDING
BOTT.
- BOTTOM
BTM.
- BOTTOM
CLG.
- CEILING
COL.
- COLUMN
CONC.
- CONCRETE
CONT.
- CONTINUE
CTR.
- CENTER
DIM.
- DIMENSION
D.S.
- DOWNSPOUT
D.W.
- DRYWALL
D.W.S. - DRY WALL STUD
E.F.
- EXHAUST FAN
EL.
- ELEVATION
ELEV.
- ELEVATION
ELEC.
- ELECTRICAL
E.W.C. - ELECTRICAL WATER COOLER
F.A.S.F. - FLUID APPLIED SEAMLESS FLOORING
F.D.
- FLOOR DRAIN
F.E.C.
- FIRE EXTINGUISHER CABINET
FL.
- FLOOR
FLR.
- FLOOR
F.R.
- FIRE RETARDANT
FSK.
- FOIL SCRIM KRAFT
F.V.
- FIELD VERIFY
GYP. BD. - GYPSUM BOARD
H.I.
- HIGH IMPACT
H.M.
- HOLLOW METAL
HDCP
- HANDICAP
INSUL. - INSULATION
LT.
- LIGHT
L
- (STELL) ANGLE
MNT.
- MOUNT
N.I.C.
- NOT IN CONTRACT
N.T.S.
- NOT TO SCALE
O.A.
- OVERALL
O.C.
- ON CENTER
OP'G
- OPENING
OPP.
OPENING
PIL.
- PILASTER
PSF
- POLYURETHANE SPRAY FOAM (INSULATION)
P.T.
- PRESSURE TREATED
REQ'D. - REQUIRED
R.D.
- ROOF DRAIN
RM.
- ROOM
S.A.T. - SUSPENDED ACOUSTIC TILE
SIM.
- SIMILAR
STL.
- STEEL
SUPT.
- SUPPORT
T.B.
- TACKBOARD
TH.
- THICK
TYP.
- TYPICAL
WD. WOOD
S-1
S-2
S-2.1
S-2.2
S-2.3
S-2.4
S-3
S-3.1
S-3.2
S-3.3
S-4
S-4.1
S-4.2
S-4.3
S-5
S-5.1
S-6
S-7
STRUCTURAL TITLE SHEET
FOUNDATION PLAN
SECOND FLOOR FRAMING PLAN
STRUCTURAL FLOOR PLANS & DETAILS
ROOF FRAMING PLAN
ROOF TRUSS PLAN
ICF WALL ELEVATIONS & DETAILS
TYPICAL STRUCTURAL DETAILS
TYPICAL STRUCTURAL DETAILS
TYPICAL STRUCTURAL DETAILS
STRUCTURAL FRAMING SECTIONS & DETAILS
STRUCTURAL FRAMING SECTIONS & DETAILS
STRUCTURAL FOUNDATION DETAILS
STRUCTURAL FOUNDATION DETAILS
TRUSS PROFILES
TRUSS PROFILES
STRUCTURAL SCHEDULES
ADD ALTERNATE CANOPY PLANS, SECTIONS & DETAILS
ARCHITECTURAL
A-0
A-1
A-2
A-2.1
A-2.2
A-2.3
A-2.4
A-3
A-3.1
A-3.2
A-3.3
A-4
A-4.1
A-5
A-5.1
A-6
A-6.1
A-7
A-7.1
A-7.2
A-7.3
A-7.4
A-8
A-9
A-9.1
A-10
A-11
LEGENDS AND WALL TYPES
SITE PLAN
FIRST FLOOR PLAN AND DETAILS
SECOND FLOOR PLAN AND DETAILS
ENLARGED PLANS AND DETAILS
ENLARGED FLOOR PLANS
FLOORING LAYOUTS
SCHEDULES
DOOR OPENING DETAILS
DOOR OPENING DETAILS
WINDOW ELEVATIONS AND DETAILS
FIRST FLOOR REFLECTED CEILING PLAN
SECOND FLOOR REFLECTED CEILING PLAN
ROOF PLAN AND DETAILS
ROOF DETAILS
BUILDING ELEVATIONS
ENLARGED BUILDING ELEVATIONS
BUILDING SECTIONS AND DETAILS
BUILDING SECTIONS AND DETAILS
BUILDING SECTIONS AND DETAILS
BUILDING SECTIONS AND DETAILS
SECTIONS AND DETAILS
WALL SECTIONS AND DETAILS
INTERIOR ELEVATIONS
INTERIOR ELEVATIONS
MILLWORK
ALTERNATE BID
P-0.1
P-1.1
P-1.2
P-1.3
P-1.4
P-3.1
P-4.1
PLUMBING LEAD SHEET
SANITARY SEWER FIRST FLOOR PLAN
SANITARY SEWER SECOND FLOOR PLAN
PLUMBING PIPING FIRST FLOOR PLAN
PLUMBING PIPING SECOND FLOOR PLAN
PLUMBING DWV DIAGRAM
PLUMBING DETAILS
HVAC
H-0.1
H-1.1
H-1.2
H-1.3
H-1.4
H-1.5
H-4.1
H-4.2
H-5.1
HVAC LEAD SHEET
HVAC FIRST FLOOR PLAN
HVAC SECOND FLOOR PLAN
HVAC ATTIC PLAN
HVAC PIPING FIRST FLOOR PLAN
HVAC PIPING SECOND FLOOR PLAN
HVAC DETAILS
HVAC DETAILS
HVAC SCHEDULES
ELECTRICAL
E-0.1
E-1.1
E-1.2
E-1.3
E-1.4
E-1.5
E-1.6
E-3.1
E-4.1
E-4.2
E-4.3
E-4.4
E-5.1
E-5.2
E-5.3
E-5.4
E-5.5
E-5.6
ELECTRICAL LEAD SHEET
ELECTRICAL FIRST FLOOR PLAN
ELECTRICAL SECOND FLOOR PLAN
ELECTRICAL POWER FIRST FLOOR PLAN
ELECTRICAL POWER SECOND FLOOR PLAN
SPECIAL SYSTEMS FIRST FLOOR PLAN
SPECIAL SYSTEMS SECOND FLOOR PLAN
ELECTRICAL RISER DIAGRAM
ELECTRICAL DETAILS
ELECTRICAL DETAILS
ELECTRICAL DETAILS
ELECTRICAL DETAILS
ELECTRICAL SCHEDULES
ELECTRICAL SCHEDULES
ELECTRICAL SCHEDULES
ELECTRICAL SCHEDULES
ELECTRICAL SCHEDULES
ELECTRICAL SCHEDULES
SET NO.
1150 BIRCH STREET BENTON, KENTUCKY 42025
MARSHALL COUNTY
PUBLIC LIBRARY
BOARD
VOL. 2 OF 2
FOR THE:
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
MARSHALL COUNTY PUBLIC LIBRARY
BENTON,
KENTUCKY
@ BENTON
UTILITY CONTACT LIST
ELECTRIC: BENTON ELECTRIC SYSTEM
MARK FISK
MAFISK@BENTONELECTRICSYSTEM.COM
270-527-3666
UC
NEW UNDERGROUND COMMUNICATIONS
UGE
NEW UNDERGROUND ELECTRIC POWER
OE
EXISTING OVERHEAD ELECTRIC
AT&T
AMANDA BERKLEY
AS0063@ATT.COM
270-444-5047
OE
EXISTING UTILITY POLE
12
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
OE
GEN
OE
3.
THE CONTRACTOR SHALL OBTAIN, AT HIS EXPENSE, ALL APPLICABLE PERMITS AND UTILITY COMPANY FEES.
4.
NEW CONNECTIONS TO UTILITIES SHALL BE COORDINATED WITH THE APPROPRIATE UTILITY COMPANIES.
5.
THESE PLANS ARE SCHEMATIC IN NATURE AND INDICATE THE APPROXIMATE AND GENERAL LOCATION OF THE
WORK. CONTRACTOR SHALL INSTALL WORK THROUGH COORDINATION WITH OTHER TRADES AND TO SUIT
FIELD CONDITIONS.
6.
THE CONTRACTOR SHALL FIELD VERIFY THE ELEVATIONS AND LOCATIONS OF ALL TIE-IN POINTS BEFORE
INSTALLING ANY UNDERGROUND PIPING OR CONDUITS.
7.
VERIFY ALL DIMENSIONS BEFORE FABRICATION.
8.
USE EXTREME CAUTION WHEN EXCAVATING. UNDERGROUND UTILITIES ILLUSTRATED ARE APPROXIMATE AND
ARE SHOWN TO ALERT CONTRACTOR TO THEIR PRESENCE. CONTRACTOR MUST LOCATE/VERIFY UTILITIES BU
HAND TOOL EXCAVATION.
9.
CONTRACTOR SHALL PATCH AND REPAIR ALL WALKS, DRIVES, GRASS, ETC. DAMAGED IN THE COURSE OF
CONSTRUCTION. THESE REPAIRS SHALL MATCH EXISTING ALIKE ITEMS IN THE AREA.
FF
14. THE CONTRACTOR SHALL FURNISH AND INSTALL SYSTEM MARKER TAPE ABOVE EACH UNDERGROUND UTILITY
SYSTEM.
3
UP
OE
ELECTRICAL
CONSTRUCTION NOTES
OE
OE
#
OE
OE
OE
OE
OE
BIRCH STREET
OE
PROPOSED
BUILDING
3
LI-C22
OE
AAP1
AA
PLACE POLE'S HAND
HOLE ORIENTED TO
THIS SIDE.
OE
BB3
3
LI-C21
AA
AAP1
OE
RD-23,25 AA
AA
PLACE POLE'S HAND
HOLE ORIENTED TO
THIS SIDE.
OE
BB3
5
OE
OE
2
ELECTRONIC MESSAGE BOARD (ALTERNATE BID A-4): COORDINATE WITH SIGN
INSTALLER PRIOR TO ROUGH-IN. FURNISH AND INSTALL ONE 1P30A NEMA 3R
FUSED DISCONNECT WITH 20 AMP FUSES. FURNISH AND INSTALL 12" x 8' COPPER
CLAD GROUND ROD AND BOND TO SIGN. FURNISH AND INSTALL A WEATHER
PROOF, WEATHER RESISTANT, WHILE-IN-USE, GFI RECEPTACLE AND TWO #10'S
AND ONE #10 GND TO INDICATED CIRCUIT.
3
FOR CAMERA CONNECTIVITY, REF. DRAWING UE-4.1, DETAIL 3. ROUTE CONDUIT
CONCEALED IN CONCRETE TO ENTRY INTO BUILDING AND TO ACCESSIBLE
CEILING.
4
FLAG POLE LIGHTING, REF. DETAIL 2, DRAWING UE-4.1 FOR DETAILS.
5
FOR CONTINUATION, REF. DRAWING E-1.1.
6
BENTON ELECTRIC SYSTEM SHALL REMOVE EXISTING POLE AND REPLACE WITH
NEW IN LOCATION SHOWN. E.C. SHALL COORDINATE WITH UTILITY FOR
ELECTRICAL CONNECTION AT NEW POLE. INCLUDE IN THE BID ALL UTILITY
COMPANY FEES. REFERENCE DETAIL 4, DRAWING UE-4.1 FOR DETAILS.
7
E.C. SHALL FURNISH AND INSTALL THREE 4" CONDUITS WITH PULL STRINGS FOR
COMMUNICATIONS. INSTALL IN SAME TRENCH AS UNDERGROUND ELECTRIC. STUB
UP 6" ABOVE GRADE AND CAP. ALL RADIUS BENDS SHALL BE LONG RADIUS
SWEEPS.
8
REFERENCE DRAWING E-3.1 "RISER DIAGRAM" FOR SPECIFIC DETAILS.
9
FOR CONTINUATION FROM, REF. DRAWING E-1.1; CONTINUATION TO, REF.
DRAWING E-1.2.
RD-19
5
11
REFERENCE DETAIL 10, DRAWING UE-4.1 FOR PAD MOUNT TRANSFORMER
DETAILS.
12
E.C. SHALL COORDINATE WITH AT&T AND INCLUDE IN BID ANY COSTS ASSOCIATED
WITH REMOVAL OF BOTH OF THE SMALLER POLES LOCATED IN THIS AREA.
OE
PLACE POLE'S HAND
HOLE ORIENTED TO
THIS SIDE.
OE
10
BACK UP GENERATOR. REF. DETAIL 5, DRAWING UE-4.1 FOR PAD MOUNT DETAILS.
REFERENCE RISER DIAGRAM DETAIL, DRAWING E-3.1 FOR ELECTRICAL
CONNECTION DETAILS. ROUTE UNDERGROUND CONDUITS IN SAME TRENCH AS
PROVIDING ENTRY TO COMMUNICATIONS AND TRANSFORMER SECONDARY
FEEDER.
OE
PROGRAM LIGHTING
CONTROL FOR ON AT
DUSK, OFF AT 11 PM.
OE
1
OE
PLACE POLE'S HAND
HOLE ORIENTED TO
THIS SIDE.
(APPLIES TO THIS DRAWING ONLY)
ELECTRONIC MESSAGE BOARD (BASE BID): E.C. SHALL DIG A 30" (MIN.) DEEP
TRENCH, FURNISH AND INSTALL ONE UNDERGROUND 1 12" CONDUIT w/PULL
STRING FOR COMMUNICATIONS. ONE UNDERGROUND 1 12" CONDUIT w/PULL
STRING FOR POWER. CAP AND STAKE CONDUITS AT LOCATION OF MESSAGE
BOARD PER DETAIL 6, DRAWING E-4.1. AT BUILDING, TURN COMMUNICATION
CONDUIT AND PULL STRING UP INTO ACCESSIBLE CEILING SPACE AND
TERMINATE. ROUTE POWER CONDUIT AND PULL STRING TO INDICATED PANEL
AND TERMINATE.
OE
AA
AAP2
OE
03/01/2018
13. THE CONTRACTOR SHALL COORDINATE THE ELEVATIONS OF THE DIFFERENT UNDERGROUND PIPING AND
CONDUIT SYSTEMS TO INSURE THAT THE ELEVATIONS OF PIPE AND/OR CONDUITS WILL NOT CONFLICT.
OE
FF
LI-C16
UGE
UC
UG
E
FF
9
11
ALL WORK SHALL BE IN ACCORDANCE WITH THE KENTUCKY BUILDING CODE, KENTUCKY STATE PLUMBING
CODE, NATIONAL ELECTRIC CODE AND OTHER LOCAL, STATE AND NATIONAL BUILDING CODES THAT APPLY.
OE
OE
E
UG
UC
8
XFMR
10
FF
2.
12. THE CONTRACTOR SHALL BE RESPONSIBLE FOR ALL EXCAVATION AND BACKFILL REQUIRED FOR THE
INSTALLATION OF THE WORK. PROVIDE STREET PLATES, BARRICADES, WARNING LIGHTS, SHORING, BRACING,
DE-WATERING EQUIPMENT, ETC. AS REQUIRED. CONDUCT EXCAVATION SO THAT WALLS, FOOTINGS, AND
ADJOINING PROPERTY ARE NOT DISTURBED OR INJURED. PROPERLY DISPOSE OF SPOILS OFF-SITE.
7
FF
EACH CONTRACTOR SHALL BE RESPONSIBLE FOR VISITING THE SITE PRIOR TO BIDDING IN ORDER TO BECOME
FAMILIAR WITH THE EXISTING CONDITIONS. ANY DISCREPANCIES OR QUESTIONS SHALL BE BROUGHT TO THE
ATTENTION OF THE ENGINEER PRIOR TO THE BID DATE.
11. FURNISH AND INSTALL COMPLETE FUNCTIONAL SYSTEMS REGARDLESS OF WHETHER OR NOT ALL ELEMENTS
ARE SPECIFICALLY CALLED OUT.
OE
OE
1.
10. ALL CONSTRUCTION SHALL COMPLY WITH OSHA AND OTHER APPROPRIATE SAFETY STANDARDS.
EAST 11TH STREET
OE
OE
6
ELM STREET
AAP2
ELECTRONIC MESSAGE BOARD,
ALTERNATE BID A-4
OE
BB1
2
4
OE
1
BB1
OE
OE
OE
BB1
RD-24
UG
UC E
OE
UG
UC E
RD-20
WP
OE
5
OE
AA
NOTICE
OE
OE
SEE CIVIL DRAWINGS FOR SITE GRADING,
ELEVATIONS AND OTHER UTILITY ROUTINGS
OE
EAST 12TH STREET
OE
PHONE:
SITE UTILITY NOTES
SITE LEGEND
EXCAVATION NOTE
PROJECT
NORTH
THIS PROJECT IS DESIGNATED AS AN UNCLASSIFIED
SOILS SITE. REFER TO THE CIVIL DRAWINGS AND
GEOTECHNICAL REPORT FOR EXISTING SUB SURFACE
CONDITIONS. THE CONTRACTOR IS RESPONSIBLE FOR
REMOVING ROCK ENCOUNTERED DURING
INSTALLATION OF ANY SPECIFIED WORK.
SITE UTILITY PLAN
SCALE: 1/16" = 1'-0"
BURIED UTILITIES NOTE
UTILITIES ARE SHOWN AT THEIR APPROXIMATE LOCATION BASED
UPON INFORMATION OBTAINED FROM UTILITY COMPANIES AND FIELD
EVIDENCE. BURIED UTILITIES MIGHT EXIST ON THE SUBJECT SITE
WHICH ARE NOT SHOWN ON THIS DRAWING. USE EXTREME CAUTION
DURING EXCAVATION PROCEDURES AND CONTACT KENTUCKY 811 @
811 OR 1-800-752-6007 FOR EXACT LOCATION OF BURIED UTILITIES
PRIOR TO EXCAVATION OPERATIONS.
Kentucky 811
Know what's
below.
Callbefore you dig.
Call 811 or 800-752-6007
www.kentucky811.com
IT'S THE LAW
SITE ELECTRIC UTILITY PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
UE-1.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
HAND HOLE AND RECEPTACLE OUTLET.
REF. POLE SPECIFICATION FOR LOCATIONS.
MAINTAIN 2FT MINIMUM BETWEEN
PEDESTRIAN WALKWAYS AND/OR
VEHICULAR HARDSCAPE AND POLE
FOUNDATION - COORDINATE
PLACEMENT.
FIXTURE "BB1". REFERENCE
LIGHTING FIXTURE SCHEDULE.
POLE (REF. FIXTURE SCHEDULE FOR DETAILS).
LABEL EACH POLE WITH BAKELITE TAG PER SPEC.
1" x 45° CHAMFER
ALL AROUND.
CONDUIT STUBBED UP ADJACENT TO HAND
HOLE. NUMBER AND SIZE AS REQUIRED.
PRODUCT'S CANOPY PLATE. REFERENCE
LIGHTING FIXTURE SCHEDULE.
ANCHOR BOLTS SHALL BE AS
RECOMMENDED BY MANUF.
COORDINATE WITH MANUFACTURER'S
INSTALLATION INSTRUCTIONS FOR
JUNCTION BOX SIZE AND TYPE.
WEATHER PROOF, WEATHER RESISTANT,
GFI DUPLEX RECEPTACLE. MOUNT AT
POLES FESTOON OUTLET.
30' FLAG POLE
BY G.C.
1P15A
120V
N
G
2'
2'
FINISHED GRADE
CIRCUIT, DIMMING CONTROL AND
COMMUNICATION CONDUCTORS
TO NEXT POLE. REFER TO SITE
PLAN AND PANEL SCHEDULE FOR
DETAILS.*
1" CONDUIT. CIRCUIT CONDUCTORS TO
NEXT FIXTURE. REFER TO SITE PLAN AND
PANEL SCHEDULE FOR DETAILS. E.C. SHALL
COORDINATE WITH OTHER SITE WORK AND
TRADE DISCIPLINES BEFORE INSTALLATION.
3
x 10' GROUND ROD.
WITH COPPER GROUND CONDUCTOR
(SIZED TO NFPA 70) ATTACHED TO
LUG WELDED TO INTERIOR OF POLE.
1" C WITH CAT 6 CABLE
AND PULL STRING.
CAT 6 JUMPER WITH
RJ45 ENDS TO PATCH
PANEL AT RACK
4"
*NOTE:
BRANCH CIRCUIT WIRING AND LOW
VOLTAGE/FIBER CABLING MUST BE
INSTALLED IN SEPARATE CONDUITS
OR SEPARATION MAINTAINED PER
NEC.
1
CONCRETE FOUNDATION - SMOOTH BORE
SONATUBE FORM ABOVE GRADE. (REMOVE
FORM AFTER CONCRETE HAS SET.)
REINFORCE VERTICALLY WITH #4 REBAR,
SAME TIE SPACING, MINIMUM OF 2" OF
CONCRETE COVER ON BARS. REINFORCE
HORIZONTALLY WITH #3 REBAR AT 12" O.C.
- PLAN VIEW -
DIA.
CAT 6 CABLE WITH RJ45 ENDS.
COIL ENOUGH LOOSE CABLE
INSIDE NEMA 4X ENCLOSURE
FOR FUTURE CONNECTION TO
CAMERA.
COPPER GROUND CONDUCTORS (SIZED TO NFPA
70) BONDED TO ALL THREE FIXTURES OR THEIR
JUNCTION BOXES AND BONDED TO THE FLAG POLE
BASE LIGHTING ARRESTOR. REFERENCE AND
COORDINATE WITH ARCHITECTURAL PLANS FOR
FLAG POLE BASE DETAILS .
REINFORCED CONCRETE PIERS.
COORDINATE WITH
ARCHITECTURAL PLANS FOR
DETAILS.
03/01/2018
6" x 4" NEMA 4X LOCKABLE ENCLOSURE.
MOUNT TO POLE LOCATED JUST ABOVE
POLES'S HAND HOLE.
1" CONDUIT. CIRCUIT CONDUCTORS
TO SOURCE, OR NEXT FIXTURE.
EQUIPMENT GROUND CONDUCTOR
ATTACHED TO FIXTURE.
4' DEPTH
CIRCUIT, DIMMING CONTROL AND
COMMUNICATION CONDUCTORS TO
SOURCE, OR NEXT POLE. EQUIPMENT
GROUND CONDUCTOR ATTACHED TO
LUG WELDED TO INTERIOR OF POLE.*
PROVIDE #6 BARE COPPER TO A 12" x 8'
GROUND ROD. BOND METAL ENCLOSURE.
LABEL RECEPTACLE "MAX. LOAD 240VA".
1" C, 2-#8'S, #8 GRD.
- SECTION VIEW -
SITE LIGHT POLE BASE
(INSTALL IN NEMA 4X ENCLOSURE)
UNDERGROUND CONDUIT SYSTEM
MDF RM 221
6" LARGER THAN
POLE BASE
SITE LIGHT POLE BASE DETAIL
2
NO SCALE
FLAG POLE LIGHTING BASE DETAIL
FIXTURE "BB2". REFERENCE
LIGHTING FIXTURE SCHEDULE.
3
NO SCALE
REMOTE CCTV DETAIL
NO SCALE
PRODUCT'S CANOPY PLATE. REFERENCE
LIGHTING FIXTURE SCHEDULE.
COORDINATE WITH MANUFACTURER'S
INSTALLATION INSTRUCTIONS FOR
JUNCTION BOX SIZE AND TYPE.
1" x 45° CHAMFER
ALL AROUND.
12"
12"
FINISHED GRADE
1" CONDUIT. CIRCUIT CONDUCTORS
TO SOURCE, OR NEXT FIXTURE.
EQUIPMENT GROUND CONDUCTOR
ATTACHED TO FIXTURE.
CONSTRUCTION NOTES:
THE GENSET, REMOTE ANNUNCIATOR AND TRANSFER SWITCH WILL BE PURCHASED BY THE
CONTRACTOR AND DELIVERED TO THE SITE. THE CONTRACTOR SHALL UNLOAD ALL
EQUIPMENT, ASSEMBLE AND INSTALL.
1" CONDUIT. CIRCUIT CONDUCTORS TO
NEXT FIXTURE. REFER TO SITE PLAN AND
PANEL SCHEDULE FOR DETAILS. E.C. SHALL
COORDINATE WITH OTHER SITE WORK AND
TRADE DISCIPLINES BEFORE INSTALLATION.
18"
2' DEPTH
3
4" x 10' GROUND ROD (ONE REQUIRED
FOR ALL THREE FIXTURES). WITH
COPPER GROUND CONDUCTORS
(SIZED TO NFPA 70) BONDED TO
FIXTURE OR JUNCTION BOX.
CONTRACTOR IS RESPONSIBLE FOR ALL COORDINATION, MATERIALS AND LABOR FOR THE
INSTALLATION, TESTING AND PLACING INTO SERVICE THE FURNISHED EQUIPMENT.
CONCRETE FOUNDATION - SMOOTH BORE
SONATUBE FORM ABOVE GRADE. (REMOVE
FORM AFTER CONCRETE HAS SET.)
REINFORCE VERTICALLY WITH #4 REBAR,
SAME TIE SPACING, MINIMUM OF 2" OF
CONCRETE COVER ON BARS. REINFORCE
HORIZONTALLY WITH #3 REBAR AT 12" O.C.
FURNISH AND INSTALL A 1P20A BREAKER TO FEED THE GENSET BATTERY CHARGER/BLOCK
HEATER, EXTEND 3-#10'S IN 3/4" C. UNDERGROUND TO THE GENSET CONTROL PANEL AND
CONNECT.
12" DIA.
FURNISH AND INSTALL FROM THE GENSET CONTROL PANEL 6-#14 THHN STR. IN 3/4"C AND
CONNECT THE A.T.S.
NEW POLE BY UTILITY
COMPANY
UTILITY NOTE:
FURNISH AND INSTALL FROM THE GENSET CONTROL PANEL 4-#14 THHN STR. IN 3/4"C AND A
SHIELDED #16 TWISTED PAIR CABLE PER GENSET MANUFACTURER, TO THE REMOTE
ANNUNCIATOR PANEL INSIDE THE BUILDING AT THE OWNERS DESIGNATED LOCATION.
"U" GUARD BY UTILITY
COMPANY
11
CONTRACTOR SHALL INCLUDE IN THE CONTRACT ALL UTILITY COMPANY FEES AND OR CHARGES ASSOCIATED WITH
ESTABLISHING ELECTRICAL SERVICE TO THE BUILDING AND OR SITE. THIS SHALL INCLUDE ALL COSTS AND MATERIAL
ASSOCIATED WITH PRIMARY CONDUIT, CABLING, POLES, METERING EQUIPMENT, TAP CABINETS, TERMINATION
CABINETS, TRANSFORMERS, DISTRIBUTION EQUIPMENT, ETC. CONTRACTOR SHALL CONTACT AND COORDINATE ALL
MAIN SERVICE REQUIREMENTS AND LOCATIONS WITH UTILITY CO. PRIOR TO BIDDING. ALL ROUGH-INS (PAD, CONDUIT,
GROUNDING, ETC SHALL COMPLY WITH UTILITY COMPANY STANDARDS.
FLOOD LIGHT BASE DETAIL
NO SCALE
PROVIDE PLAQUE ON THE A.T.S. TO INDICATE SERVICE DISCONNECT.
ALL INSTALLATIONS SHALL HAVE A REMOTE MANUAL STOP STATION OF A TYPE TO PREVENT
INADVERTENT OR UNINTENTIONAL OPERATION LOCATED OUTSIDE THE ROOM HOUSING THE
PRIME MOVER, WHERE SO INSTALLED, OR ELSEWHERE ON THE PREMISES WHERE THE
PRIME MOVER IS LOCATED OUTSIDE THE BUILDING.
DOOR WIDTH
DOOR WIDTH
DOOR WIDTH
# 4 REBAR @ 12" E. W. IN
MIDDLE OF POUR
TYPICAL 1/2"X8'
GROUND ROD
METER PEDESTAL AND
METERING CONDUIT.
#3/0 BARE
CU.-TYP.
AREA TO REMAIN OPEN TO
BOTTOM FOR TYPICAL
CONDUIT TURN-UPS.
CONDUIT ENTRY
AREA
C
L.V.
L.V.
H.V.
H.V.
20''
TOP VIEW
B
2"
4"
TURN CONDUIT UP 6"
ABV GRADE AND CAP.
CLEAR. REQ'D.
FOR DOOR
FIN. GRADE
GROUND LAID IN DENSE
GRADE
MARKER TAPE
FIN. GRADE
8"
30"
12"
SCH. 80 PVC SIZE PER FEEDER
DIAGRAM
ADJUST VERTICAL DIMENSION TO
MAINTAIN 30" FROM BOTTOM OF
FOOTING TO FINISHED GRADE
LONG RADIUS
SWEEPS.
PROVIDE 5' TAIL FOR
CONNECTION TO
SECONDARY NEUTRAL
BUSHING.
2 # 4 REBAR
CONTINIOUS (TYP.)
24"
3-PHASE XFMR
KVA RATING
NOTE:
COORDINATE ALL PAD DIMENSIONS
WITH THE EQUIPMENT INSTALLED
ADJUST AS REQUIRED
TYPICAL ELECTRICAL RISER DETAIL
@ UTILITY POLE
5
GENSET PAD ELEV. DETAIL
GENSET PAD PLAN DETAIL
NO SCALE
NO SCALE
NO SCALE
A
B
C
D
E
225, 300, 500
90
60
6
52
20
750, 1000, 1500
2000, 2500, 3000
108
108
6
52
24
PROTECTION NOTES:
GRADE
1. CONCRETE TESTING, 4000 PSI - 4% TO 6% ENTRAINED AIR, 3/4'' MAX SIZE AGGREGATE.
2. REINFORCING STEEL, ATSM-A615 GRADE 60, PLACE APPROX. 6'' O.C. EACH WAY AND SECURELY TIE TOGETHER.
COMPACTED BACKFILL
HAZARD TAPE
3. MINIMUM CONCRETE COVER OVER REINFORCING STEEL 3 INCHES.
4. WOOD FLOAT FINISH. LEAVE NO DEPRESSIONS.
5. METER SHALL BE MOUNTED ON SUITABLE UNISTRUT SUPPORT ATTACHED TO CONCRETE PAD, PER UTILITY COMPANY STANDARDS.
CONCRETE WITH
RED DIE
MIN. BURIAL
NOTE:
DETAILS 6, 7 AND 8 ARE APPLICABLE
TO SERVICE LATERALS ONLY.
CONTRACTOR SHALL LOCATE ALL STUB-OUTS
ACCORDING TO UTILITY ENGINEERING DEPARTMENT.
CONTRACTOR SHALL LEAVE OPENINGS IN PAD TO
ALLOW ACCESS OF CONDUIT TERMINATIONS AND
FUTURE CONDUIT STUB-OUTS. DO NOT POUR SOLID IN
THIS AREA.
NOTES:
NOTE:
ALL CONDUITS EXPOSED ABOVE
GRADE SHALL BE R.G.S.
GUARD POSTS BOLLARDS SHALL BE PROVIDED TO PROTECT TANKS THAT ARE
SUBJECT TO VEHICULAR DAMAGE. WHEN GUARD POSTS ARE INSTALLED, THE
FOLLOWING DESIGN REQUIREMENTS SHALL BE MET:
(1) THEY SHALL BE CONSTRUCTED OF STEEL NOT LESS THAN 6" IN DIAMETER
AND SHALL BE FILLED WITH CONCRETE.
(2) THEY SHALL BE SPACED NOT MORE THAN 4' ON CENTER.
(3) THEY SHALL BE SET NOT LESS THAN 3' DEEP IN CONCRETE FOOTING OF NOT
LESS THAN 15" DIAMETER.
NOTE:
DIMENSION IN INCHES
6"
NOTE:
COORDINATE WITH LOCAL UTILITY
FOR ALL SERVICE REQUIREMENTS
4
A
# 4 REBAR @ 12"
3" ENVELOPE OF DENSE
GRADE ON ALL SIDES
PVC
8" THICK CONC.
EQUIP. PAD. REFER
TO GENSET ELEV.
DETAIL.
HAZARD TAPE 6" BELOW GRADE
DEPTH PER UTILITY
48" MIN.
RGS
D
E
6. INFORMATION DEPICTED IS FOR GENERAL INFORMATIONAL PURPOSES - FINAL LAYOUT CONFIGURATIONS, CLEARANCES, ETC AND
SIZES BY UTILITY.
WIRE MESH EMBEDDED
IN 6" CONCRETE SLAB
CHAMFER
EDGES
COORD. WITH UTILITY
FOR STUB-UP HEIGHT
SEE SPECIFICATION FOR
RESTORATION
FINAL GRADE
SEE SPECIFICATION
FOR RESTORATION
HAZARD TAPE 6" BELOW GRADE
CONDUIT TYPICAL,
QUANTITY AS
P.V.C./R.N.C.
12"
11.5"
BACK FILL WITH CONCRETE EQUAL TO
DUCT BANK OR FLOWABLE FILL
(~80-100 PSI)
TYPICAL CONDUIT
STUB-OUT
UNDISTURBED SOIL
FRONT VIEW
CRUSHED STONE FOR
CONTAINMENT AS
REQUIRED BY UTILITY
19"
NOTE:
APPLIES TO ALL EXTERIOR CONDUITS
FROM BELOW GRADE.
7.5"
BACK FILL WITH
EXCAVATED DIRT,
STRAW AND SEED
R.G.S.
24" MIN.
24" MIN.
22''
UNDISTURBED SOIL
9
DUCT BANK SEE
DUCT BANK
SECTIONS
6
UNDISTURBED SOIL OR CONCRETE
EQUAL TO DUCT BANK OR FLOWABLE
FILL (~80-100 PSI) ONLY AS FILL
UNDER DUCT BANK
TRENCH SECTION DETAIL (UNDER
GRASS OR SOD AREA)
NO SCALE
DUCT BANK SEE
DUCT BANK
SECTIONS
7
NO SCALE
NO SCALE (APPLIES TO UNDERGROUND FEEDERS)
DUCT BANK TO HAVE PLASTIC SPACES TO
MAINTAIN SEPARATION. CONCRETE TO BE
3000 PSI, < 5" SLUMP, FIBERGLASS
REINFORCED. PROVIDE RED DYE ON TOP
UNDISTURBED SOIL OR CONCRETE
EQUAL TO DUCT BANK OR FLOWABLE
FILL (~80-100 PSI) ONLY AS FILL
UNDER DUCT BANK
TRENCH SECTION DETAIL (UNDER
TRAFFIC AREA)
EXTERIOR CONDUIT TRANSITION DETAIL
8
TYPICAL DUCT BANK SECTION
NO SCALE
10
UTILITY TRANSFORMER PAD DETAIL
NO SCALE
SITE ELECTRIC DETAILS
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
UE-4.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
ED
T
EC
U
HRL
T
E AL
V
EECE W
L
S PA
S
M.AND
E
T
YSPIPEED
S
E ED UIR
P
I
-P NIZREQ
Y
A
DR
LVNGS
A
G TTI
FI
OT
R
P
8 P
3
PS
5
ED
T
S
LI BLY E L)
L
U EMNGL UATED
D
Q
LEASSH SIR ETEC
B
ERDELEM OPRO
EM
2
S
S
I
S
F
T
O
R
A
S O
E- GELE MSYD
E
R
U
I
P EL A B C K S
D ELI LOOUT
(RTERTE
IN CAE.
L O AC
SP
F
17
12
N
EI
T
AE
CC
O
L PA
S
AC
V
20
13 1
6
4
8P
7
/2"
1
1
E.
P
TE
C
TE
O
R
ING DE
P
I
P
SI
T
D
U
IZE IN O
N
A
LV DRA
A
G
TO
1"
E
UT
O
R
D, IC
E
L
UIRRAU
M
E
Q
P E E
-PIYSITG R HYD
T
S
WEER0 PS ITH
KLM 2TE W)
OM
N
R
I
F PR MU NA NS
S INI IDI TIO
(M RRULA
COLC
CA
STATIC:
125
PSI
RESIDUAL:
80
PSI
WATER FLOW:
1089
GPM
DURATION:
90
MINS.
SOURCE OF WATER SUPPLY:
CITY OF BENTON
SOURCE OF WATER FLOW DATA:
MR. SEAVERS; CITY OF BENTON
5.
WORK SHALL BE PERFORMED BY A LICENSED FIRE PROTECTION CONTRACTOR.
DATE OF WATER FLOW TEST:
10/17/2016
6.
CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING SYSTEM DESIGN AND APPROVED SHOP DRAWINGS IN COMPLIANCE
WITH THE KENTUCKY BUILDING CODE.
ANTICIPATED WATER DEMAND:
40
PSI
7.
THE SYSTEM TYPE SHALL BE: AUTOMATIC WET PIPE. WITH A SINGLE INTERLOCK PREACTION SYSTEM FOR ONE SPACE.
360
GPM
8.
SPRINKLERS SHALL BE PENDANT, UPRIGHT AND SIDEWALL AS NOTED. PENDANT AND SIDEWALL SPRINKLERS IN OCCUPIED
SPACES SHALL BE SEMI-RECESSED AS NOTED, WHITE POWDER COATED. UPRIGHT SPRINKLERS SHALL BE BRASS.
9.
NEW CONNECTIONS TO UTILITIES SHALL BE COORDINATED WITH THE APPROPRIATE UTILITY COMPANIES.
10.
THESE PLANS ARE SCHEMATIC IN NATURE AND INDICATE THE APPROXIMATE AND GENERAL LOCATION OF THE WORK.
CONTRACTOR SHALL INSTALL WORK THROUGH COORDINATION WITH OTHER TRADES AND TO SUIT FIELD CONDITIONS.
11.
UNLESS OTHERWISE NOTED, ALL PIPING SHALL BE CONCEALED IN WALLS OR CEILINGS.
12.
COORDINATE ENTIRE PIPING LAYOUT WITH ALL OTHER TRADES TO ENSURE PROPER INSTALLATION AND REQUIRED
CLEARANCES.
13.
VERIFY ALL DIMENSIONS BEFORE FABRICATION.
14.
USE EXTREME CAUTION WHEN EXCAVATING. UNDERGROUND UTILITIES ILLUSTRATED ARE APPROXIMATE AND ARE SHOWN TO
ALERT CONTRACTOR TO THEIR PRESENCE. CONTRACTOR MUST LOCATE/VERIFY UTILITIES BY HAND TOOL EXCAVATION.
15.
THE CONTRACTOR SHALL BE RESPONSIBLE FOR DAMAGE THAT OCCURS TO NEW WORK AND/OR NEW EQUIPMENT IN THE
COURSE OF CONSTRUCTION.
16.
CONTRACTOR SHALL BE RESPONSIBLE FOR REMOVING AND REPLACING CEILING TILES AND GRID WORK AS REQUIRED FOR
WORK. ANY DAMAGED TILE OR GRID WORK SHALL BE REPAIRED/REPLACED AT CONTRACTOR'S EXPENSE.
17.
CONTRACTOR SHALL PATCH AND REPAIR ALL WALL, FLOOR, ROOF AND CEILING PENETRATIONS MADE IN THE COURSE OF
CONSTRUCTION. PENETRATIONS SHALL BE SLEEVED, FLASHED (IF NECESSARY), SEALED AIRTIGHT AND FINISHED TO MATCH
ADJACENT AREAS.
18.
ALL SPRINKLERS SHALL BE RATED FOR 175°F UNLESS NOTED TO BE HIGH TEMPERATURE. HIGH TEMPERATURE SPRINKLERS
SHALL BE 250°F RATED.
19.
CONTRACTOR SHALL SLOPE ALL PIPING TO THE SYSTEM MAIN DRAIN TO INSURE PROPER DRAINAGE. THE CONTRACTOR IS
RESPONSIBLE FOR FURNISHING ADDITIONAL AUXILIARY DRAINS TO ALLOW ALL PIPING TO BE DRAINED AS NECESSARY.
20.
SPRINKLERS SHALL BE CENTERED IN BOTH DIRECTIONS WITHIN CEILING TILES. SPRINKLERS SHALL BE VISUALLY ALIGNED AND
INSTALLED SYMMETRICALLY IN AREAS WITH DRYWALL CEILINGS AND/OR EXPOSED INSTALLATIONS.
CLASSIFICATION OF HAZARD(S):
LIGHT HAZARD AND ORDINARY HAZARD GROUP 1
CLASSIFICATION OF BUILDING
A-3 LIBRARY
SPECIFIC TYPES OF SUPPRESSION SYSTEM(S):
AUTOMATIC WET PIPE WITH A SINGLE INTERLOCK PREACTION SYSTEM FOR ONE
SPACE
NFPA 13 AND 24
SPRINKLER WORK DESCRIPTION
MINIMUM CLASSIFICATION OF OCCUPANCY
LH
OCCUPIED SPACE SPRINKLER
DESCRIPTION
A
SEMI-RECESSED PENDANT SPRINKLERS REQUIRED
B
UPRIGHT SPRINKLERS REQUIRED
C
SEMI-RECESSED SIDEWALL SPRINKLERS REQUIRED
21.
SPRINKLERS IN MECHANICAL, MACHINE, AND COMMUNICATION ROOMS SHALL BE RATED FOR HIGH TEMPERATURE.
D
PREACTION SYSTEM - DRY UPRIGHT SPRINKLERS REQUIRED
22.
MECHANICAL, MACHINE AND COMMUNICATION ROOMS SHALL BE SUPPLIED WITH BRANCH LINES ONLY.
23.
DO NOT INSTALL PIPING OR SPRINKLERS DIRECTLY OVER ELECTRICAL PANELS. COORDINATE ROUTINGS WITH ELECTRICAL
CONTRACTOR.
24.
TAMPER SWITCHES, FLOW SWITCHES, CONTROL PANELS, ETC. SHALL BE MONITORED BY THE BUILDING FIRE ALARM SYSTEM.
COORDINATE WORK WITH ELECTRICAL CONTRACTOR.
25.
PROVIDE INSPECTOR'S TEST CONNECTION AS SPECIFIED. INSTALL WITH LABELED ACCESSIBLE TEST VALVE AND ORIFICED
UNION ROUTED TO THE MAIN DRAIN.
26.
PIPE SUPPORTS SHALL BE INSTALLED FOR SEISMIC DESIGN CATEGORY D AS SPECIFIED IN THE KENTUCKY BUILDING CODE.
27.
PREPARE, PRIME AND PAINT ALL PIPE, SUPPORTS AND HANGERS NOT CONCEALED.
28.
PROTECT FIRE PROTECTION PIPING THAT IS INSTALLED UNDERGROUND FROM CORROSION PER NFPA 13 REQUIREMENTS.
29.
THE FIRE PROTECTION SYSTEM DESIGN SHALL BE BASED ON THE FOLLOWING OCCUPANCY CLASSIFICATIONS:
LH
LIGHT HAZARD OCCUPANCY
OH GR 1
ORDINARY HAZARD GROUP 1 OCCUPANCY
DESCRIPTION
SUPERVISED CONTROL VALVE (NORMALLY OPEN)
2
LOCKING SOLENOID VALVE (NORMALLY CLOSED)
3
WATER FLOW ALARM PRESSURE SWITCH
4
AUTOMATIC DRAIN VALVE
5
SUPERVISED BYPASS VALVE FOR MANUAL OPERATION (NORMALLY CLOSED)
6
ALARM TEST VALVE (NORMALLY CLOSED)
7
AUXILIARY DRAIN VALVE (NORMALLY CLOSED)
8
WATER PRESSURE GAUGE
9
DRAIN CUP
ALL WORK SHALL BE IN ACCORDANCE WITH NFPA 13, "INSTALLATION OF SPRINKLER SYSTEMS", NFPA 24 "INSTALLATION OF
UNDERGROUND PIPING SYSTEMS", THE KENTUCKY BUILDING CODE AND ALL LOCAL BUILDING CODES/REQUIREMENTS THAT
APPLY.
THE CONTRACTOR SHALL OBTAIN, AT HIS EXPENSE, APPLICABLE PERMITS AND "TAP-ON" FEES.
A
1
2.
4.
TAG
NUMBER
EACH CONTRACTOR SHALL BE RESPONSIBLE FOR VISITING THE SITE PRIOR TO BIDDING IN ORDER TO BECOME FAMILIAR WITH
THE EXISTING CONDITIONS. ANY DISCREPANCIES OR QUESTIONS SHALL BE BROUGHT TO THE ATTENTION OF THE ENGINEER
PRIOR TO THE BID DATE.
WORK SHALL BE ACCEPTABLE TO THE LOCAL FIRE MARSHAL. CONTRACTOR IS RESPONSIBLE FOR CORRECTING ANY WORK TO
RECEIVE INSPECTION APPROVAL.
SPRINKLER SYSTEM LEGEND
D
1.
3.
NFPA STANDARD(S) FOLLOWED IN DESIGN:
SYSTEM COMPONENTS
10
FIRE PROTECTION NOTES
FIRE SUPPRESSION DESIGN CRITERIA
9
1
LV
A
V NG
DD
I
E
S
L
I
I
RV BU
E
M
UPWITSHTE
S
AL CE SY
C
I
P FA RM
TYTERALA
INRE
FI
E
N PAC
I
RS
DS
E
E
L CT
KE
N
I
PRROT
S
Y,
ERON P
R
H
A
I
V
OATCT
LL
O
I
T RE
P
EW
L
11
TY S
S
1
1
R LAN
E
KLO P
N
I
R RT
SP
FE
E
R
NOTE:
G
N
I
D
DUAL
ACTION REQUIRED FOR RELEASE OF WATER
IL THEREBY
U
GUARDING AGAINST INADVERTENT WATER
BM
DAMAGE.
H
ITSTE
W
CEM SY
A
F R
ERALA
N
T
IO
INRE
S
T
E EAC
FI
RM
E
K
A
R
I
ALG F
MO PR E
S
E
R S INPAC
ACLDINEM
E
F
d
THTORD S
ERBUIYST
O
2nARM
E
T
INITH M S
EC
CT
TO
AL
T
E
W AR
t
DE OT
L
1sARM 14
A
PR
AL
15
SD
16
SD
16
NOTES:
1. THE FIRE PROTECTION CONTRACTOR SHALL BE RESPONSIBLE FOR FURNISHING
AND INSTALLING ALL NECESSARY FIRE PROTECTION SPRINKLERS TO PROVIDE
100% COVERAGE PER NFPA 13.
2. CONTRACTOR SHALL NOTE THE COMPLEX CEILING TYPES AND SOFFITS. REFER TO
ARCHITECTURAL CEILING PLANS. CONTRACTOR SHALL INSTALL ADDITIONAL
SPRINKLERS AS REQUIRED TO AVOID SPRAY OBSTRUCTIONS.
03/01/2018
SEE FIRE SUPPRESSION DESIGN CRITERIA
30.
PIPING MATERIALS SHALL BE LISTED EQUIVALENT GRADE OR BETTER:
FIRE MAIN - C900 PVC
FIRE WATER - C900 PVC
FIRE SPRINKLER - STEEL PIPE IN SCHEDULE AS SPECIFIED
10
CHECK VALVE
11
20 OR LESS AUTOMATIC SPRINKLER(S) (NORMALLY CLOSED)
12
UL LISTED SYSTEM CONTROL PANEL WITH BATTERY BACKUP (INSTALL IN PROTECTED SPACE)
13
120 VOLT POWER (COORDINATE WITH ELECTRICAL CONTRACTOR)
14
ALARM BELL (INTERFACE WITH FIRE ALARM SYSTEM)
15
TROUBLE BELL (INTERFACE WITH FIRE ALARM SYSTEM)
16
SYSTEM SMOKE DETECTORS (INSTALLED IN CROSSED ZONE CONFIGURATION)
17
MANUAL EMERGENCY PULL STATION
31.
KEY BOXES SHALL BE RECESSED KEY BOX WITH HINGED DOOR (KNOX-BOX MODEL 3200 OR EQUAL). MOUNT BOXES 60" TO TOP
OF BOX ABOVE FINISHED WALK SURFACE. ARCHITECT SHALL SELECT COLOR AND FINAL MOUNTING LOCATION.
32.
CONTRACTOR SHALL COORDINATE THE FOLLOWING WITH THE LOCAL FIRE MARSHAL AND/OR FIRE DEPARTMENT:
A. TYPE AND LOCATION OF KEY BOXES.
B. TYPE AND LOCATION OF FIRE DEPARTMENT CONNECTION.
C. HOSE THREAD SPECIFICATION FOR FIRE DEPARTMENT CONNECTION AND HYDRANTS.
D. SIGNAGE AT FIRE DEPARTMENT CONNECTION.
FIRE PROTECTION LEGEND
SYMBOL
DESCRIPTION
FM
FIRE PROTECTION MAIN
FW
FIRE WATER SERVICE
SIDEWALL SPRINKLER
GATE VALVE
OS&Y VALVE W/ TAMPER SWITCH
L
EL
B
IC
R
LL
T
E
C
B
LE
IC
E
R
R
CT
IO
E
R
EL
TE
M
X
R
E
AR
O
I
L
TO
ER
EA
T
B
R
F IR U
N
I
I
E
/F
SY E PILDIN
G
R
ST RO G
AU
WE
G
EM TE
O
CT
P
RE
H
U
ION
T
S
I
CEHW
ES
T
I
R
P
AT
SIW
N
OW D
NT
FLOOR
E
M
C
P
E
AS
B
6"
FS
AL)
RU
L
C
H
L
I
L
T
A
N
A
ILILNSCTHYAPIC
R
(T
E ADNDL ME
L
R
A
FM
COALLSEASE
WINKEVE
L LE
S
6"
4"
2"
VADR
LV AIN
E(
TY
P.)
D
2"
IN
RA
E
L IN
F
ON
T
ERAI
T
UD
RIONK/
S
2
OR
O
L
FW
ES
R
P
S
VIL D
CIORANK
NT
E
TOS FIONOR
M TO
RNGAT W
T
E
R
R
I
U AL
A FER
EF
P
N
RR
I
AW
N
DE. RSEFO
DONITTIO
E
N G AND
R
CDD
I
O
I
N
F
K
A
MECATWIIONOR
O
NLNDRUAATL W
FR
O
CIVI TINON
CONITI
4" CD
D
A
VE
L
VA
G
N
CI
U
ED
R
E
UR
"
.
36
LR
F
.
FIN
OS
CO&Y
AL OR VA
DO
AR DI LV
PR UB
M (NA E W
ES LE
TY TE ITH
CH
S
P) WI T
U
PIP
TH AM
RE EC
AS E S
PO PE
RE K B
PR RE UP
WER S
DU AC
PA EPAQU PO
CINKF
R / WI
LO
INT R IRERT
FIRTCH
G
E, D S
W
V
E ;
A
PR
LV PRE
IME
E VE
,A
NT
ND
ER
AUTOMATIC SPRINKLER RISER DIAGRAM
NO SCALE
CHECK VALVE
PRESSURE REDUCING VALVE
DOUBLE DETECTOR BACKFLOW PREVENTOR
FS
P
FLOW SWITCH
PRESSURE GAUGE
ELECTRIC BELL
KEY
PREPARE, PRIME AND PAINT
FD MASTER KEY BOX (KNOX-BOX MODEL 3200 OR
EQUAL)
SPRINKLER SYSTEM
BRANCH LINE OR MAIN.
THREADED SLIP NUT AND
PIPE NIPPLE.
READILY ACCESSIBLE
LOCATION AND LABELED
(MIN. SIZE 1" DIA.)
BRAIDED STAINLESS STEEL
FLEXIBLE SPRINKLER DROP/HOSE IN
ACCORDANCE WITH NFPA.
UNION
SECURE SPRINKLER WITH
MANUFACTURER SUPPLIED
ADJUSTABLE SUPPORT SYSTEM.
SLEEVE AND SEAL
EQUAL TO OR
GREATER THAN 5
LINEAR FEET TO
OUTLET
45° ELL
SEMI-RECESSED, WHITE SPRINKLER.
CENTER SPRINKLER IN CEILING TILE.
PREPARE, PRIME AND PAINT
16"
1
NON-SUPERVISED SINGLE INTERLOCK PREACTION SYSTEM WITH ELECTRIC
RELEASE RISER DIAGRAM
SUSPENDED CEILING. REFER TO
ARCHITECTURAL DRAWINGS.
SPRINKLER DROP DETAIL
SMOOTH BORE CORROSION RESISTANT
OUTLET GIVING FLOW EQUIVALENT TO
ONE SPRINKLER OF A TYPE HAVING THE
SMALLEST ORIFICE INSTALLED ON THIS
SYSTEM
(REQUIRED AT ALL SUSPENDED CEILINGS)
NO SCALE
FIN. FLOOR
FIRE PROTECTION LEAD SHEET
INSPECTOR'S TEST CONNECTION DETAIL
NO SCALE
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
FP-0.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
MECHANICAL
CONSTRUCTION NOTES
(APPLIES TO THIS DRAWING ONLY)
#
1
INSTALL SPRINKLER WIRE GUARDS IN THIS AREA. GUARDS SHOULD BE SUITABLE
TO PREVENT ACCIDENTAL DAMAGE.
2
ONLY BRANCH LINE MAY BE INSTALLED IN THIS AREA. DO NOT ROUTE MAINS THRU
THIS AREA.
3
INSTALL HIGH TEMPERATURE SPRINKLERS RATED 250 DEGREES FAHRENHEIT.
4
PREPARE, PRIME AND PAINT ALL EXPOSED PIPING, SUPPORTS, ETC. COLOR SHALL
BE SELECTED BY ARCHITECT.
5
INSTALL FIRE DEPARTMENT KEY BOX; SEE FIRE PROTECTION NOTES. COORDINATE
LOCATION WITH ARCHITECTURAL DRAWINGS.
6
COORDINATE SPRINKLER SYSTEM INSTALLATION WITH EQUIPMENT, DUCTWORK,
PIPING, ELECTRICAL PANELS, ETC. TO BE INSTALLED IN MECH/ELEC ROOM.
FURNISH ADDITIONAL SPRINKLERS TO AVOID SPRAY OBSTRUCTIONS.
7
DO NOT ROUTE SPRINKLER PIPING OVER ELECTRICAL EQUIPMENT.
8
CONTRACTOR SHALL SPRINKLE UNDER ALL INTERMEDIATE STAIR LANDINGS.
REFER TO ARCHITECTURAL DRAWINGS FOR DETAILS.
9
CONTRACTOR SHALL REFER TO ARCHITECTURAL DRAWINGS FOR COMPLEX
CEILING DETAILS. CEILING GEOMETRY MAY REQUIRE ADDITIONAL SPRINKLERS TO
AVOID OBSTRUCTIONS AND PROVIDE 100 PERCENT COVERAGE.
FM
FW
W
5
KEY
STAIR
110
2
FP-0.1
LH
PLUMBING
B&C
8
4
STORAGE
125
FR1
MECH./ELEC.
10
B
124
OH GR 1
1
B
11
FR1
BM OFFICE
3
A
BOOK MOBILE
LH
INTERIOR ALARM BELL.
11
COORDINATE SPRINKLER SYSTEM INSTALLATION WITH EQUIPMENT, DUCTWORK,
PIPING, ELECTRICAL PANELS, ETC. FURNISH ADDITIONAL SPRINKLERS TO AVOID
SPRAY OBSTRUCTIONS.
121
B
3
STAFF TOILET
123
119
LH
A
A
OH GR 1
6
CORRIDOR
A
10
122
OH GR 1
1
FR1
7
ELECTRICAL
HVAC
9
OH GR 1
3
9
LH
TOILET
111
A
LH
CUSTODIAL
118
WORKROOM
A
WOMEN
OH GR 1
117
114
A
YOUTH PROGRAM
CHILDREN/JUVENILE
109
107
A
LH
A
9
A
LH
OH GR 1
BRANCH MNGR
115
LH
A
LH
9
CIRCULATION
112
A
MEN
116
LH
A
9
LH
BOOK RETURN
102
A
LH
YOUNG ADULTS
108
A
COLLECTIONS
106
LH
9
A
LH
9
VESTIBULE
5
101
A
LH
KEY
9
STAIR
104
B&C
4
LH
8
FR1
ELEV.
103
C
OH GR 1
1
3
2
FR1
EQUIP.
105
B
OH GR 1
1
2
3
7
CLASSIFIED ASSEMBLY LEGEND
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
FIRE PROTECTION FIRST FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
FP-1.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
G
03/01/2018
MECHANICAL
CONSTRUCTION NOTES
(APPLIES TO THIS DRAWING ONLY)
G
#
5
6
STAIR
110
FM
FW
W
LH
HVAC
REF.
A
8
B
OH GR 1
1
3
9
ELECTRICAL
LH
10
14
MDF
221
11
11
A
LH
A
A
3
INSTALL HIGH TEMPERATURE SPRINKLERS RATED 250 DEGREES FAHRENHEIT.
4
PREPARE, PRIME AND PAINT ALL EXPOSED PIPING, SUPPORTS, ETC. COLOR SHALL
BE SELECTED BY ARCHITECT.
5
6" FIRE MAIN. SEE CIVIL DRAWINGS FOR CONTINUATION AND ADDITIONAL WORK.
6
4" FIRE WATER LINE FROM REMOTE FIRE DEPARTMENT CONNECTION. SEE CIVIL
DRAWINGS FOR CONTINUATION AND ADDITIONAL WORK.
7
INSTALL SINGLE INTERLOCK PREACTION ASSEMBLY. REFER TO DIAGRAM.
8
EXTERIOR ALARM BELL. COORDINATE LOCATION WITH ARCHITECTURAL
DRAWINGS.
9
COORDINATE SPRINKLER SYSTEM INSTALLATION WITH EQUIPMENT, DUCTWORK,
PIPING, ELECTRICAL PANELS, ETC. TO BE INSTALLED IN MECH/ELEC ROOM.
FURNISH ADDITIONAL SPRINKLERS TO AVOID SPRAY OBSTRUCTIONS.
LH
1
2
3
(OPEN TO BELOW)
LH
10
ALL PIPING WITH FITTINGS FOR THE PREACTION SYSTEM SHALL BE GALVANIZED.
11
DO NOT ROUTE SPRINKLER PIPING OVER ELECTRICAL EQUIPMENT.
4
12
INSTALL PREACTION SYSTEM CONTROL PANEL AND ALL ASSOCIATED
APPARATUSES. REFER TO DIAGRAM.
13
REFER TO ARCHITECTURAL AND STRUCTURAL DRAWINGS FOR FOLDING PARTITION
AND ABOVE CEILING STRUCTURAL SUPPORT. PROVIDE ADDITIONAL SPRINKLERS
AS REQUIRED FOR PARTITION IN FOLDED AND UNFOLDED POSITION TO PROVIDE
100% COVERAGE.
14
ROUTE ALL SPRINKLER PIPING HIGH AS POSSIBLE. COORDINATE WITH LIGHT
FIXTURES, DUCTWORK PIPING, STRUCTURE, ETC.
LH
15
CONTRACTOR SHALL REFER TO ARCHITECTURAL DRAWINGS FOR COMPLEX
CEILING DETAILS. CEILING GEOMETRY MAY REQUIRE ADDITIONAL SPRINKLERS TO
AVOID SPRAY OBSTRUCTIONS AND PROVIDE 100 PERCENT COVERAGE.
OH GR 1
LH
FAMILY
218
LH
RESEARCH
213
A
A
WOMEN
216
LH
A
LH
LH
COMPUTER LAB
214
A
DIRECTOR
210
A
D
A
FILES
224
FR1
A
ONLY BRANCH LINE MAY BE INSTALLED IN THIS AREA. DO NOT ROUTE MAINS THRU
THIS AREA.
STAFF TOILET
219
VESTIBULE
212
BOOK KEEPER
211
2
12
CORRIDOR
225
A
TECH LAB
220
FM
A
INSTALL SPRINKLER WIRE GUARDS IN THIS AREA. GUARDS SHOULD BE SUITABLE
TO PREVENT ACCIDENTAL DAMAGE.
7
MECH/ELEC
222
HVAC
FR1
DW
BREAK ROOM
223
1
LH
LH
MAKER
215
13
A
LH
15
MEN
217
A
LH
A/V-STACKS
209
A
D
W
LH
15
UTILITY
202
CORRIDOR
201
ICE
MTG. STORAGE
207
A
OH GR 1
STUDY
208
A
REF.
DW
A
A
OH GR 1
LH
STUDY
205
CATER
206
LH
A
A
LH
STAIR
104
LH
A
LH
FR1
ELEV.
103
C
1
MEETING ROOM B
204
A
LH
MEETING ROOM A
203
A
13
15
LH
OH GR 1
2
3
FR1
STORAGE
203A
A
OH GR 1
15
CLASSIFIED ASSEMBLY LEGEND
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
FIRE PROTECTION SECOND FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
FP-1.2
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
PLUMBING NOTES
PLUMBING FIXTURE SCHEDULE
PIPE SIZE
PIPE SIZE
PIPE SIZE
PIPE SIZE
PIPE SIZE
PIPE SIZE
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
P-1
WATER CLOSET
3"or4"
4"
1"
---
P-2
WATER CLOSET
3"or4"
4"
1"
---
P-3
WATER CLOSET
3"or4"
4"
1"
---
P-4
URINAL
2"
2"
3/4"
---
P-5
URINAL
2"
2"
3/4"
---
P-6
LAVATORY
1-1/2"
2"
1/2"
1/2"
REMARKS: WATER CLOSET, FLUSH VALVE, ADA ACCESSIBLE.
REMARKS: WATER CLOSET, FLUSH VALVE, REGULAR.
REMARKS: WATER CLOSET, FLUSH VALVE, CHILD/JUVENILE ADA
ACCESSIBLE.
KOHLER MODEL # K-4368-B "HIGHCLIFF" FLOOR
MOUNTED, VITREOUS CHINA, ELONGATED RIM, 1-1/2"
TOP SPUD, LOW CONSUMPTION, FLOOR MOUNTED
RIM A MAXIMUM HEIGHT OF 17" ABOVE FINISHED
FLOOR.
KOHLER MODEL # K-4350 "WELLCOMME" FLOOR
MOUNTED, VITREOUS CHINA, ELONGATED RIM, 1-1/2"
TOP SPUD, LOW CONSUMPTION, FLOOR MOUNTED
RIM A MAXIMUM HEIGHT OF 15" ABOVE FINISHED
FLOOR.
REMARKS: URINAL, WALL HUNG, REGULAR.
KOHLER MODEL # K-96053 "WELLCOMME" FLOOR
MOUNTED, VITREOUS CHINA, ELONGATED RIM, 1-1/2"
TOP SPUD, LOW CONSUMPTION, SEAT HEIGHT MUST
BE 15" EXACTLY ABOVE FINISHED FLOOR.
KOHLER MODEL # K-13516 EXPOSED FLUSH VALVE,
MANUALLY OPERATED, LOW CONSUMPTION 1.6 GPF,
CHROME PLATED WITH HIGH BACK PRESSURE
VACUUM BREAKER.
KOHLER MODEL # K-13516 EXPOSED FLUSH VALVE,
MANUALLY OPERATED, LOW CONSUMPTION 1.6 GPF,
CHROME PLATED WITH HIGH BACK PRESSURE
VACUUM BREAKER.
KOHLER MODEL # K-13516 EXPOSED FLUSH VALVE,
MANUALLY OPERATED, LOW CONSUMPTION 1.6 GPF,
CHROME PLATED WITH HIGH BACK PRESSURE
VACUUM BREAKER.
KOHLER SOLID PLASTIC, WHITE, ANIT-MICROBIAL
PROTECTED, ELONGATED SEAT WITH OPEN FRONT,
EXTENDED BACK AND CHECK HINGE; LESS COVER.
KOHLER SOLID PLASTIC, WHITE, ANIT-MICROBIAL
PROTECTED, ELONGATED SEAT WITH OPEN FRONT,
EXTENDED BACK AND CHECK HINGE; LESS COVER.
KOHLER SOLID PLASTIC, WHITE, ANIT-MICROBIAL
PROTECTED, ELONGATED SEAT WITH OPEN FRONT,
EXTENDED BACK AND CHECK HINGE; LESS COVER.
KOHLER MODEL # K-4989-T "FRESHMAN" VITREOUS
CHINA, 1.0 GPF LOW CONSUMPTION, SIPHON JET
FLUSH ACTION, WALL HUNG WITH 3/4" TOP SPUD.
KOHLER MODEL # K-4989-T "FRESHMAN" VITREOUS
CHINA, 1.0 GPF LOW CONSUMPTION, SIPHON JET
FLUSH ACTION, WALL HUNG WITH 3/4" TOP SPUD.
KOHLER MODEL # K-76319 "PRIMME", EXPOSED
FLUSH VALVE, MANUAL OPERATED, LOW
CONSUMPTION 1.0 GPF, DURABLE CAST BRASS
CONSTRUCTION, CHROME PLATED, HIGH BACK
PRESSURE VACUUM BREAKER.
KOHLER MODEL # K-76319 "PRIMME", EXPOSED
FLUSH VALVE, MANUAL OPERATED, LOW
CONSUMPTION 1.0 GPF, DURABLE CAST BRASS
CONSTRUCTION, CHROME PLATED, HIGH BACK
PRESSURE VACUUM BREAKER.
PIPE SIZE
PIPE SIZE
PIPE SIZE
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
MARK
FIXTURE
TRAP
P-7
EWC
1-1/2"
2"
1/2"
---
P-8
SINK
1-1/2"
2"
1/2"
1/2"
P-9
LAVATORY
1-1/2"
REMARKS: ELECTRIC WATER COOLER - ADA DUAL HEIGHT WITH
BOTTLE FILLING STATION.
REMARKS: THREE COMPARTMENT, LAY-IN.
1/2"
KOHLER MODEL # K-15182-4NDRA SINGLE HANDLE
OPERATED FAUCET, 4-3/16" STATIONARY SPOUT
REACH, PREMIUM METAL CONSTRUCTION, CHROME
PLATED. FURNISH WITH 1.2 GPM VANDAL-RESISTANT
AERATOR.
JUST MODEL # J-35 STAINLESS STEEL CUP
STRAINER WITH REMOVABLE BASKET AND CHROME
PLATED TAILPIECE, 4" LONG.
MOUNT LOWEST SPOUT AT A MAXIMUM HEIGHT OF
36" ABOVE FINISHED FLOOR.
1/2"
2"
H.W.
KOHLER MODEL # K-2005 "KINGSTON" SERIES
21-1/4"x18-1/8" VITREOUS CHINA, WALL HUNG
LAVATORY. DRILLED FOR CONCEALED ARM CARRIER.
MOUNT RIM AT 34" ABOVE FINISHED FLOOR.
JUST MODEL # B-1122, CHROME PLATED, 8"
CENTERS, DECK MOUNT FAUCET, 10" TUBULAR
BRASS SWING SPOUT WITH 2.2 GPM VANDAL
RESISTANT AERATOR. WITH LEVER HANDLES.
(TWO FAUCETS REQUIRED).
JAY R. SMITH MODEL # 0834L ELECTRIC WATER
COOLER SUPPORT SYSTEM WITH TOP AND BOTTOM
PLATES, FLOOR MOUNTED.
C.W.
REMARKS: LAVATORY, WALL HUNG, ADULT ADA ACCESSIBLE.
JUST MODEL # TL-1843-A-GR, 18"x43"x7-1/2"
SELF-RIMMING, 18 GAUGE STAINLESS STEEL SINK
WITH CENTER DRAINS.
ELKAY MODEL # LZSTL8WSSK BI-LEVEL,
BARRIER-FREE, VANDAL RESISTANT BUBBLER, WALL
MOUNTED WITH WATER FILTER, STAINLESS STEEL
FINISH AND BOTTLE FILLING STATION. BOTTLE
FILLING STATION SHALL INCLUDE AN ELECTRONIC
SENSOR FOR NO-TOUCH ACTIVATION AND BOTTLE
COUNTER.
WASTE
ZURN MODEL # Z1224 PLATE TYPE SYSTEM
LAVATORY WITH BACK.
3/8" CHROME PLATED SUPPLIES WITH STOP.
FIXTURE
TRAP
P-10
LAVATORY
1-1/2"
WASTE
2"
C.W.
1/2"
H.W.
REMARKS: LAVATORY, WALL HUNG, CHILD/JUVENILE ADA
ACCESSIBLE.
OUTDOOR CLEANOUTS SHALL TERMINATE FLUSH WITH GRADE AND BE EMBEDDED IN CONCRETE FINISHED 12"W x 12"L x 6"TK.
10
COORDINATE SANITARY SEWER PIPING WITH STRUCTURAL MEMBERS AS REQUIRED. SEE ARCHITECTURAL AND STRUCTURAL DRAWINGS FOR
RESTRICTIONS.
11
ILLUSTRATED HORIZONTAL SANITARY SEWER DRAIN LINES SHALL BE UNDERSTOOD TO BE INSTALLED BENEATH FLOOR. HORIZONTAL VENT PIPING AND
WATER PIPING SHALL BE INSTALLED ABOVE CEILINGS, UNLESS NOTED OTHERWISE.
12
COORDINATE PLUMBING ROUTING IN CEILING SPACES TO AVOID CONFLICTS WITH FIRE PROTECTION, HVAC, SPECIAL SYSTEMS, LIGHTING, NEC
CLEARANCES, ETC. DO NOT INSTALL PIPING DIRECTLY OVER ELECTRICAL PANELS OR SWITCHGEAR.
13
CONCEAL ALL PLUMBING, PIPING, ETC. IN CEILING AND/OR WALL SPACES (UNLESS NOTED OTHERWISE). PROVIDE ALL NECESSARY ACCESS DOORS IN
INACCESSIBLE CEILINGS OR WALLS TO ALLOW ACCESS FOR VALVES, TRAP PRIMERS, ETC.
14
SLEEVE ALL PLUMBING, PIPING, VENTS, ETC. THROUGH NEW ROOF, FLOOR, AND/OR WALLS. PIPE SLEEVES SHALL BE SCHEDULE 10 AND GALVANIZED
STEEL. SLEEVES ARE NOT REQUIRED FOR CORE DRILLED HOLES.
15
FLASH AND SEAL ALL ROOF, FLOOR, AND WALL PENETRATIONS.
16
FIRE STOP ALL PENETRATIONS THROUGH FIRE RATED ASSEMBLIES. FIRE STOPPING METHOD AND MATERIALS SHALL BE UL LISTED. FIRE COLLARS WILL
BE REQUIRED IF PIPING IS COMBUSTIBLE. CHANGING PIPE MATERIAL TO METAL AT PENETRATION IS ACCEPTABLE.
17
PLACE MILDEW RESISTANT SILICONE SEALANT AROUND ALL PLUMBING FIXTURES THAT CONTACT CASEWORK, WALLS, FLOORS, OR ANY OTHER HARD
SURFACES. COLOR SHALL MATCH ADJACENT SURFACE.
18
COVER ALL OPENINGS ON WATER CONVEYANCE ITEMS (PIPING, COMPONENTS, AND/OR EQUIPMENT), WHETHER STORED OR INSTALLED, TO PREVENT
ACCUMULATION OF CONSTRUCTION DEBRIS.
19
INSTALL ARRESTORS AT ALL FIXTURE SUPPLIES. ARRESTORS SHALL BE FABRICATED DURING ROUGH-IN WITH TEE, LINE SIZE PIPE (MINIMUM 6" LONG), AND
PIPE CAP.
20
INSTALL MANUFACTURED HAMMER ARRESTORS ON ALL PIPES SUPPLYING QUICK ACTING VALVES.
21
SECURE PLUMBING ROUGH-IN TO BUILDING STRUCTURE TO PROHIBIT MOVEMENT OF FLUSH VALVE ACTUATORS, HOSE BIBBS, WALL HYDRANTS, FIXTURE
SUPPLY STOP VALVES, ETC.
22
INSTALL HOSE BIBBS 18" ABOVE FINISHED FLOOR, UNLESS NOTED OTHERWISE. INSTALL FREEZE PROOF WALL HYDRANTS 18" ABOVE FINISHED GRADE,
UNLESS NOTED OTHERWISE.
23
INSTALL DIELECTRIC CONNECTIONS AT ALL DISSIMILAR MATERIAL PIPING JOINTS AND AT SLAB FOR UNDERGROUND PIPE ENTRANCES.
24
AT A MINIMUM, INSTALL TRAP PRIMERS FOR ALL FLOOR DRAINS AND OPEN RECEPTACLES LOCATED IN ROOMS THAT HAVE COMBUSTION EQUIPMENT.
REFER TO DRAWINGS FOR OTHER TRAP PRIMER LOCATIONS.
25
INSTALL A PRESSURE RELIEF VALVE ON EACH WATER HEATING UNIT AND/OR TANK. ROUTE DISCHARGE LINE PER PLUMBING CODE TO AN ACCEPTABLE
DRAIN.
26
INSTALL A DRAIN LINE FOR ALL EQUIPMENT (WATER HEATERS, TANKS, ETC.) REQUIRING A DRAIN. THE DRAIN SIZE (AT A MINIMUM) SHALL BE EQUAL TO THE
UNIT'S CONNECTION SIZE BUT IN NO CASE SHALL BE LESS THAN 3/4" DIAMETER.
27
INSTALL SUPPLY CHECK VALVES ON COLD AND HOT WATER CONNECTIONS TO THE FOLLOWING FIXTURE TYPES: MOP SINKS, SERVICE SINKS, AND ANY
OTHER FIXTURE WHERE CROSSOVER IS POSSIBLE. THESE MAY BE OMITTED IF INTEGRAL CHECK VALVES ARE FURNISHED WITH THE FIXTURE/FAUCET(S).
28
DOMESTIC WATER ISOLATION VALVES SHALL BE ONE PIECE BRONZE BALL TYPE. PLASTIC BODY VALVES ARE NOT ACCEPTABLE.
29
FOR THIS PROJECT, MINIMUM PIPING MATERIALS SHALL BE AS LISTED BELOW. REFER TO WRITTEN SPECIFICATIONS FOR ADDITIONAL REQUIREMENTS.
PIPE SIZE
FIXTURE
TRAP
WASTE
C.W.
H.W.
P-11
SINK
1-1/2"
2"
1/2"
1/2"
P-12
SINK
1-1/2"
2"
1/2"
1/2"
REMARKS: SINGLE COMPARTMENT SINK, UNDERMOUNT, EXTRA
DEEP.
REMARKS: SINGLE COMPARTMENT SINK, LAY-IN, ADA
ACCESSIBLE.
JUST MODEL # USXD-1824-A, 18"X24"X12" DEEP
SEAMLESS, 18 GAUGE, TYPE 304 STAINLESS STEEL
SINK WITH CENTER DRAIN.
JUST MODEL # SL-ADA-2131-A-GR 21"x31"x6-1/2"
SELF-RIMMING, 18 GAUGE, TYPE 304 STAINLESS
STEEL SINK, SUPPLY WITH CENTER DRAIN.
T & S BRASS MODEL # B-0221 DECK MOUNTED
MIXING FAUCET ON 8" CENTER, WITH INTERNAL
CARTRIDGES, SPRING CHECKS AND LEVER
HANDLES, 12" SWING NOZZLE.
KOHLER MODEL # K-15171-PT "CORALAIS" DECK
MOUNTED SINGLE HANDLE, 10" SWING SPOUT,1.8
GPM AERATOR, METAL CONSTRUCTION CHROME
FINISH.
JUST MODEL # J-35 STAINLESS STEEL CUP
STRAINER WITH REMOVABLE BASKET AND CHROME
PLATED TAILPIECE, 4" LONG.
JUST MODEL # J-35 STAINLESS STEEL CUP STRAINER
WITH REMOVABLE BASKET AND CHROME PLATED
TAILPIECE, 4" LONG.
3/8" CHROME PLATED SUPPLIES WITH STOP.
POLISHED CHROME PLATED GRID STRAINER.
CHROME PLATED KENTUCKY CODE "P" TRAP.
INSTALL WASTE AND SUPPLY PIPING COVER
(TRUBRO LAV GUARD 2 OR EQUAL) IN COMPLIANCE
WITH ICC/ANSI A117.1 - LATEST EDITION.
INSTALL WASTE AND SUPPLY PIPING COVER
(TRUBRO LAV GUARD 2 OR EQUAL) IN COMPLIANCE
WITH ICC/ANSI A117.1 - LATEST EDITION.
3/8" CHROME PLATED SUPPLIES WITH STOP.
MIFAB SERIES MI-SOLID-S FLOOR MOUNTED
LACQUERED CAST IRON SEDIMENT INTERCEPTOR
WITH INTERNAL STAINLESS STEEL PERFORATED
SEDIMENT BUCKET REMOVABLE THROUGH TOP.
ACID RESISTANT EPOXY COATING, GASKETED LID
SECURED WITH SINGLE HANDLE. 2" IPS THREADED
CONNECTIONS. MODIFY CASEWORK FOR FIT.
CHROME PLATED KENTUCKY CODE "P" TRAP.
CHROME PLATED KENTUCKY CODE "P" TRAP.
PIPE SIZE
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
MARK
FIXTURE
TRAP
WASTE
C.W.
H.W.
P-13
MOP BASIN
3"
3"
1/2"
1/2"
P-14
SINK
1-1/2"
2"
1/2"
1/2"
P-15
SINK
1-1/2"
2"
1/2"
1/2"
WATER INDOOR: TYPE L RIGID COPPER PIPE WITH SOLDERED FITTINGS
JUST MODEL # USXD-1824-A, 18"X24"X12" DEEP
SEAMLESS, 18 GAUGE, TYPE 304 STAINLESS STEEL
SINK WITH CENTER DRAIN.
T & S BRASS MODEL # B-0211 DECK MOUNTED MIXING
FAUCET ON 8" CENTER, WITH INTERNAL CARTRIDGES,
SPRING CHECKS AND LEVER HANDLES, 12" SWING
NOZZLE.
JUST MODEL # DL-ADA-2233-A-GR 22"x33"x6-1/2"
SELF-RIMMING, 18 GAUGE, TYPE 304 STAINLESS
STEEL SINK, SUPPLY WITH CENTER DRAIN.
APPROVED EQUAL MANUFACTURER'S:
WATER CLOSET, URINAL, LAVATORIES: KOHLER, ZURN, SLOAN, AMERICAN STANDARD OR APPROVED EQUAL
SEWER OUTDOOR: PVC PIPE WITH PRESSURE FITTINGS (REFER TO CIVIL DRAWINGS)
KOHLER MODEL # K-15171 "CORALAIS" DECK
MOUNTED SINGLE HANDLE, 10" SWING SPOUT,1.8
GPM AERATOR, METAL CONSTRUCTION CHROME
FINISH.
FLUSH VALVES: ZURN, SLOAN, AMERICAN STANDARD OR APPROVED EQUAL
SEWER INDOOR: SCH 40 PVC PIPE WITH DWV FITTINGS OR COPPER DWV PIPING
WATER INDOOR, UNDER SLAB: PEX TUBING OR ANNEALED COPPER TUBING (NO JOINTS UNDER SLAB)
SUMP DISCHARGE: SCH 40 PVC PIPE WITH PRESSURE FITTINGS
FAUCETS: DELTA, KOHLER, ZURN, KOHLER, AMERICAN STANDARD, JUST OR APPROVED EQUAL
FUEL GAS OUTDOOR, BURIED: SDR 11 POLYETYLENE TUBING (REFER TO CIVIL DRAWINGS)
ELECTRIC WATER COOLERS: HALSEY TAYLOR, ELKAY, HAWS OR APPROVED EQUAL
JUST MODEL # J-35 STAINLESS STEEL CUP STRAINER
WITH REMOVABLE BASKET AND CHROME PLATED
TAILPIECE, 4" LONG.
JUST MODEL # J-35 STAINLESS STEEL CUP STRAINER
WITH REMOVABLE BASKET AND CHROME PLATED
TAILPIECE, 4" LONG.
FUEL GAS OUTDOOR, ABOVE GRADE: SCH 40 GALVANIZED CARBON STEEL PIPE WITH SCRWD FITTINGS (GALV.)
MOP SINKS: ZURN, FIAT, PROFLO OR APPROVED EQUAL
FUEL GAS INDOOR: SCH 40 CARBON STEEL PIPE (FITTINGS PER NFPA)
30
INSULATE COLD WATER PIPING AND HOT WATER (INCLUDING RECIRCULATION) PIPING PER WRITTEN SPECIFICATIONS.
3/8" CHROME PLATED SUPPLIES WITH STOP.
31
SEISMICALLY SUPPORT ALL EQUIPMENT, PIPE, PLUMBING, ETC. PER THE STATE BUILDING CODE AND SEISMIC DESIGN CATEGORY C.
CHROME PLATED KENTUCKY CODE "P" TRAP.
32
INSTALL SUPPORT CONNECTIONS PER ROOF FRAMING MANUFACTURER'S REQUIREMENTS WHEN SUSPENDING SYSTEMS FROM PRE-ENGINEERED LIGHT
GAUGE STEEL TRUSSES.
33
PROVIDE ALL WATER HEATERS WITH MANUFACTURER'S START-UP AND CERTIFIED REPORT FOR ENGINEER'S APPROVAL. INSTALLING CONTRACTOR
START-UP IS NOT ACCEPTABLE.
34
ALL PLUMBING SUPPLIES TO FIXED-IN-PLACE EQUIPMENT SHALL BE CHROME PLATED TUBING WHERE EXPOSED OR COPPER TUBING WHERE CONCEALED.
USED OF FLEXIBLE HOSE CONNECTIONS FOR FIXED EQUIPMENT AND FIXTURES IS NOT ACCEPTABLE.
STAINLESS STEEL LAY-IN SINKS: JUST MFG., ELKAY, AMERICAN STANDARD OR APPROVED EQUAL
3/8" CHROME PLATED SUPPLIES WITH STOP.
FIAT MODEL # 830-AA SERVICE FAUCET, CHROME
PLATED BRONZE WITH VACUUM BREAKER, INTEGRAL
STOPS, ADJUSTABLE WALL BRACE, PAIL HOOK,
FOUR-ARM HOT AND COLD HANDLES, 3/4" HOSE
THREAD SPOUT.
CHROME PLATED KENTUCKY CODE "P" TRAP.
DESCRIPTION
SS
SANITARY SEWER PIPING
G
GAS PIPING
ACCESSIBLE FIXTURE DETAILS
SPECIALTY ITEMS
PLUMBING LEGEND
SYMBOL
03/01/2018
WATER OUTDOOR: PVC PIPE WITH PRESSURE FITTINGS (REFER TO CIVIL DRAWINGS)
REMARKS: TWO COMPARTMENT SINK, LAY-IN, ADA.
REMARKS: SINGLE COMPARTMENT SINK, UNDERMOUNT, EXTRA
DEEP.
OPTIONS TO INCLUDE:
- STAINLESS STEEL BUMPER GUARD
- HOSE AND HOSE BRACKET
- MOP HANGER
- STAINLESS STEEL DRAIN
- WALL GUARD #20 GAUGE TYPE 304 STAINLESS
STEEL (2 PANELS FOR 24"x24" BASIN).
9
3/8" CHROME PLATED SUPPLIES WITH STOP.
MARK
CHROME PLATED KENTUCKY CODE "P" TRAP.
FIAT MODEL # MSB 2424 HIGH DENSITY COMPOSITE
MOLDED MOP BASIN, 24"x24"x10" WITH STAINLESS
STEEL DOME STRAINER / LINT BASKET AND A PVC
DRAIN WITH ADJUSTABLE CAULKING NUT AND
GASKET.
VERIFY ALL INVERT ELEVATIONS AND DIMENSIONS BEFORE FABRICATION AND/OR INSTALLATION. DISCOVER ALL POINT OF CONNECTIONS AND ESTABLISH
ELEVATIONS AND PITCH PRIOR TO BEGINNING ANY INSTALLATION.
H.W.
3/8" CHROME PLATED SUPPLIES WITH STOP.
REMARKS: MOLDED HIGH DENSITY COMPOSITE MOP SERVICE
BASIN.
THESE PLANS ARE SCHEMATIC IN NATURE AND INDICATE THE APPROXIMATE AND GENERAL LOCATION OF PLUMBING, PIPING, AND/OR EQUIPMENT.
COORDINATE INSTALLATION OF WORK WITH OTHER DRAWINGS AND TRADES. PRECISELY LOCATE ALL PLUMBING FIXTURE LAYOUTS AND HEIGHTS PER
ARCHITECTURAL DRAWINGS IN LIEU OF PLUMBING DRAWINGS.
8
C.W.
POLISHED CHROME PLATED GRID STRAINER.
PIPE SIZE
5
ZURN MODEL # Z8700 SERIES "P" TRAP.
WASTE
3/8" CHROME PLATED SUPPLIES WITH STOP.
PIPE SIZE
THE CONTRACTOR SHALL ACQUIRE PLUMBING PERMIT(S), COORDINATE ALL INSPECTIONS, AND PAY ALL ASSOCIATED FEES (INCLUDING TAP FEES).
BE AWARE THAT SEVERAL UTILITIES ARE LOCATED IN THE GROUND BELOW THE PROJECT CONSTRUCTION LIMITS. EXERCISE CAUTION WHEN EXCAVATING.
UTILIZE HAND TOOLS TO LOCATE EXISTING UTILITIES PRIOR TO MACHINE EXCAVATION.
TRAP
KOHLER MODEL # K-15182-4NDRA SINGLE HANDLE
OPERATED FAUCET, 4-3/16" STATIONARY SPOUT
REACH, PREMIUM METAL CONSTRUCTION, CHROME
PLATED. FURNISH WITH 1.2 GPM VANDAL-RESISTANT
AERATOR.
4
7
FIXTURE
KOHLER MODEL # K-2005 "KINGSTON" SERIES
21-1/4"x18-1/8" VITREOUS CHINA, WALL HUNG
LAVATORY. DRILLED FOR CONCEALED ARM CARRIER.
MOUNT RIM AT 31" ABOVE FINISHED FLOOR.
ALL WETTED PLUMBING ITEMS SHALL COMPLY WITH NSF 372 DRINKING WATER SYSTEM COMPONENTS - LEAD CONTENT. ALL SUPPLIERS MUST ASSURE
COMPLIANCE REGARDLESS OF PRODUCTS SPECIFIED WITHIN THE CONSTRUCTION DOCUMENTS.
COORDINATE NEW CONNECTIONS TO UTILITIES WITH THE APPROPRIATE UTILITY COMPANY(S). INSTALL WORK PER UTILITY COMPANY REQUIREMENTS AND
OBTAIN NECESSARY UTILITY COMPANY APPROVALS.
MARK
1/2"
3
6
PIPE SIZE
ZURN MODEL # Z1224 PLATE TYPE SYSTEM
LAVATORY WITH BACK.
CHROME PLATED KENTUCKY CODE 'P' TRAP.
MOUNT HIGHEST SPOUT AT A MAXIMUM HEIGHT OF
40" ABOVE FINISHED FLOOR.
MARK
ACCESSIBLE PLUMBING FIXTURES SHALL BE INSTALLED PER THE STATE BUILDING CODE IN ACCORDANCE WITH THE LATEST EDITION OF ICC/ANSI A117.1
ACCESSIBLE AND USABLE BUILDINGS AND FACILITIES.
DELTA MODEL # K-5313-4 "REFINIA" COLLECTION,
MANUAL OPERATED SINGLE HANDLE DECK MOUNT
FAUCET WITH 1.2 GPM AERATOR.
MOUNT WITH LIP AT A MAXIMUM HEIGHT OF 17"
ABOVE FINISHED FLOOR.
PIPE SIZE
2
KOHLER MODEL # K-2000 "CAXTON", 17-3/8"x13"
VITREOUS CHINA, UNDERMOUNT, RECTANGULAR
WITH OVERFLOW. COLOR TO BE DETERMINED BY
ARCHITECT.
ZURN MODEL Z1222 FLOOR MOUNTED, CONCEALED
URINAL SUPPORT.
MOUNT WITH LIP AT A MAXIMUM HEIGHT OF 24"
ABOVE FINISHED FLOOR.
ALL WORK SHALL BE IN ACCORDANCE WITH THE STATE BUILDING CODE, STATE PLUMBING CODE, STATE BOILER CODE, NFPA 54 NATIONAL FUEL GAS CODE,
INTERNATIONAL MECHANICAL CODE, AND OTHER LOCAL/STATE/ NATIONAL CODES OR STANDARDS THAT APPLY.
REMARKS: LAVATORY, UNDERMOUNT, REGULAR HEIGHT.
REMARKS: URINAL, WALL HUNG, ADA ACCESSIBLE.
ZURN MODEL Z1222 FLOOR MOUNTED, CONCEALED
URINAL SUPPORT.
1
MARK
DESCRIPTION
BFP-1
BACKFLOW PREVENTER
WATTS SERIES LF007 MODEL LF007-QT-FDA LEAD FREE 2-1/2" DOUBLE CHECK VALVE ASSEMBLY BACKFLOW PREVENTER WITH
QUARTER TURN BALL VALVES AND STRAINER ASSEMBLY.
BFP-2
BACKFLOW PREVENTER
WATTS SERIES 009 - 009QT 1" REDUCED PRESSURE ZONE ASSEMBLY WITH BRONZE STRAINER.
CO-1
CLEANOUT
NO SCALE
REMARKS
MOUNT MIRROR AT
ANGLE FROM WALL
COLD WATER PIPING
BTM OF MIRROR
ZURN MODEL # ZN1400 LEVEL-TROL ADJUSTABLE FLOOR CLEAN OUT, DURA-COATED CAST IRON BODY WITH GAS AND WATERTIGHT
BRONZE TAPERED THREAD PLUG AND ROUND SCORIATED SECURE NICKEL BRONZE TOP WITH VANDAL-PROOF SCREWS.
EXPANSION TANK
THERMAL EXPANSION TANK
FD
FLOOR DRAIN
FD-1
FLOOR DRAIN
ZURN MODEL # ZN415 4" TYPE "B" FLOOR DRAIN (ROUND TOP) FLOOR DRAIN WITH 4" DIAMETER NICKEL BRONZE, VANDAL PROOF
STRAINER.
FWH
FD-2
FLOOR DRAIN
ZURN MODEL Z662 16"x16" DURA-COATED CAST IRON BODY WITH 4" BOTTOM OUTLET, SEEPAGE PAN AND COMBINATION MEMBRANE
FLASHING CLAMP AND FRAME FOR HEAVY DUTY SLOTTED LOOSE GRATE WITH SUSPENDED SEDIMENT BUCKET.
FS-1
FLOOR SINK
JAY R. SMITH MODEL 3410 SANI-CEPTOR ACID RESISTANT COATED FLOOR AND INDIRECT WASTE DRAIN. 8"x8"x6"DEEP CAST IRON
FLANGED RECEPTOR, 6" SUMP DEPTH, A.R.C. 1/2 GRATE, VANDAL PROOF SCREWS, AND ALUMINUM SEDIMENT BUCKET. 3" ∅ OUTLET.
SET WITH RIM 1" ABOVE FINISHED FLOOR
FS-2
FLOOR SINK
ZURN MODEL # Z1910-K-21 8" X 8 X 6" DEEP CAST IRON FLANGED RECEPTOR WITH WHITE ACID RESISTANT PORCELAIN ENAMEL
INTERIOR, ANCHOR FLANGE WITH SEEPAGE HOLES AND CLAMP COLLAR, HALF GRATE, 4" DIAMETER OUTLET.
FWH-1
FREEZEPROOF WALL
HYDRANT
GT-1
GREASE TRAP
ZURN MODEL # GT2700 CORROSION RESISTANT COATED INTERIOR AND EXTERIOR FABRICATED STEEL GREASE TRAP, FLOW RATE 4
G.P.M., RATED AT 8 LB GREASE CAPACITY, WITH FLOW DIFFUSING BAFFLE, INTEGRAL TRAP, AND VENTED INLET FLOW CONTROL.
HB-1
HOSE BIBB
WOODFORD MODEL 24 WALL FAUCET WITH LOOSE TEE KEY AND POLISHED CHROME FINISH. INSTALL HOSE BIBB 18" ABOVE FINISHED
FLOOR.
HB-2
HOSE BIBB
WOODFORD MODEL 24 WALL FAUCET WITH METAL WHEEL HANDLE AND BRASS FINISH. INSTALL HOSE BIBB 42" ABOVE FINISHED FLOOR
(UNLESS OTHERWISE NOTED).
IMB-1
ICE MAKER OUTLET BOX
FREEZE PROOF WALL HYDRANT
GT
GREASE TRAP
HB
HOSE BIBB
IMB
ICE MAKE BOX
SP
SUBMERSIBLE PUMP
TP
TRAP PRIMER
VTR
VENT THRU ROOF
WB
WASHER BOX
WH
WATER HEATER
BALL VALVE
GAS VALVE
DOUBLE CHECK BACKFLOW PREVENTER WITH
PRESSURE REDUCING VALVE
NOTE:
INSTALL PLUMBING GUARDS ON
PIPING BELOW ACCESSIBLE LAV.
WATER HEATER MOUNT
MFG.
MODEL
LAVATORY
3-1/2"
MAX.
13-1/2"
MIN.
IPS MODEL # 9700 WATER TITE ICE MAKER OUTLET BOX. CHROME 1/4 TURN ADAPTER BALL VALVE WITH 1/2" COPPER SWEAT
CONNECTIONS.
OPEN RECEPTACLE
4" OPEN RECEPTACLE WITH HUB EXTENDED 1" ABOVE FINISHED FLOOR.
OR-2
OPEN RECEPTACLE
2" OPEN RECEPTACLE WITH HUB EXTENDED 1" ABOVE FINISHED FLOOR.
OWS-1
OIL / WATER
SEPARATOR
PRV-1
PRESSURE REDUCING
VALVE
WATTS SERIES LF223, 2-1/2" LEAD FREE HIGH CAPACITY WATER PRESSURE REDUCING VALVE. SET OUTLET PRESSURE TO 60 PSIG.
SP-1
SUBMERSIBLE PUMP
ZOELLER "MIGHTY-MATE" MODEL 57 AUTOMATIC FLOAT OPERATED ALL CAST IRON 115V/1∅, 0.3HP, 35GPM @ 10 TDH. SUPPLY WITH
OILSMART MODEL SOSSA-50 ALARM SYSTEM AS SPECIFIED ON DETAIL.
MOUNT
TYPE
HEIGHT
(IN.)
LENGTH
(IN.)
DEPTH
(IN.)
WEIGHT
(LBS.)
SERVICE
OR
LOCATION
TEMP.
MIN.
MAX.
RISE
FLOW FLOW
SETTING
(GPM) (GPM)
(DEG.F)
RECOVERY
TEMP.
RISE
(DEG.)
TP-1
TRAP PRIMER
PRECISION PLUMBING PRODUCTS MODEL # PR-500 PRIME-RITE TRAP PRIMER WITH DU-4 (DISTRIBUTION UNIT).
(GPM)
WB-1
WASHER BOX
GUY GRAY MODEL # NWFBED2004 RECESSED WASHING MACHINE OUTLET BOX WITH 120V AND 220V ELECTRICAL OUTLETS, FURNISHED
WITH 1/2" MIP/SWEAT VALVES AND A 2" THREADED DRAIN FITTING. COORDINATE LOCATION WITH ELECTRICAL CONTRACTOR.
WCO-1
WALL CLEAN OUT
GAS
INPUT
(MBH)
THERMAL
EFF.
NATURAL
OR
PROPANE
VOLTAGE /
PHASE
(V/PH)
FLA
(AMPS)
REMARKS AND
ACCESSORIES
WH-1A
RINNAI
C199i
1
WALL
56.7
22
13.8
83
MECH/ELEC
124
0.2
9.8
110
63
8.1
199
96%
NATURAL
120/1
8
SEE BELOW
WH-1B
RINNAI
C199i
1
WALL
56.7
22
13.8
83
MECH/ELEC
124
0.2
9.8
110
63
8.1
199
96%
NATURAL
120/1
8
SEE BELOW
COORDINATE
ACTUATOR &
GRAB BAR FOR
PROPER ACCESS
H
F.F.
8"MIN.
KNEE CLEARANCE
PLAN VIEW
MAX. TOE CLEARANCE
17" MIN.
TANKLESS GAS WATER HEATER SCHEDULE
MARK
ELEVATION
17" MIN.
NATURAL GAS REGULATOR
NUMBER
OF WATER
HEATERS
8"MIN. 6"MAX.TOE CLEARANCE
KNEE CLEARANCE
WOODFORD MODEL 67 AUTOMATIC DRAINING WALL HYDRANT WITH LOOSE TEE KEY OPERATION AND CHROME FINISH.
OR-1
GAS METER SET
B
A
F.F.
6"
REDUCED PRESSURE ZONE BACKFLOW
PREVENTER
F.F.
AMTROL MODEL ST-5 THERMAL EXPANSION TANK.
11-1/2"
ET
G
ET-1
NOTE:
WATER CLOSET STYLE
MAY VARY
F
CIRCULATION PUMP
40" MAX.
CIRCULATING PUMP
COMBINATION CLEANOUT
CP
BELL AND GOSSETT MODEL # NBF-36 IN-LINE WET ROTOR CIRCULATION PUMP FOR OPEN (POTABLE) WATER SYSTEM WITH LEAD FREE
BRONZE BODY, 23 GPM @ 15 FT HD, 270 WATTS, 3300 RPM, 115 VOLT, SINGLE PHASE.
CP-1
9"
MIN.
CCO
4" CAST IRON CLEANOUT DOUBLE TEE SUITABLE FOR CLEANOUT / TESTING EITHER UPSTREAM OR DOWNSTREAM. WITH BRONZE PLUG.
D
CLEANOUT
COMBINATION
CLEANOUT/ TEST TEE
C
CO
CCO-1
MIN.
BACKFLOW PREVENTER
9"
BFP
11-1/2"
TOP OF LAV
VENT PIPING
E
HOT WATER PIPING
F.F.
URINAL
WATER COOLER
AGE GROUP
(YEARS OLD)
5-8 & 9-12
13 & UP
E
FLOOR MOUNT WATER CLOSET
A
B
C
D
F
(INCHES)
(INCHES)
(INCHES)
(INCHES)
(INCHES)
(INCHES)
24 MIN.
27 MIN.
31 MAX.
34 MAX.
24 MIN.
27 MIN.
30 MAX.
36 MAX.
40 MAX.
44 MAX.
14 MAX.
17 MAX.
G (INCHES)
15
17
15
19
H (INCHES)
15
16
15
18
ZURN MODEL #Z1446 CLEAN OUT TEE, DURA-COATED CAST IRON BODY, GAS AND WATERTIGHT BRONZE TAPERED THREAD PLUG AND
ROUND, SMOOTH STAINLESS STEEL ACCESS COVER WITH VANDAL PROOF SCREWS.
REMARKS AND ACCESSORIES:
A. BOSCH, RINNAI, NAVIEN, OR APPROVED EQUAL.
B.
SEALED COMBUSTION, DIRECT VENT. HORIZONTAL VENT REQUIRED. AT SECOND FLOOR.
C. FURNISH WITH MANUFACTURER'S CONDENSATE NEUTRALIZATION KIT.
D. FURNISH WITH HORIZONTAL CONCENTRIC VENT.
E.
PROVIDE MANUFACTURES START-UP. SEE PLUMBING NOTES.
IMPORTANT NOTICE
1. EXTERIOR WALLS FOR THIS BUILDING ARE CONSTRUCTED OF ICF (INSULATED CONCRETE FORM).
THE SUBCONTRACTORS SHALL COORDINATE NECESSARY ROUGH-IN OF SYSTEMS WITHIN WALLS.
THIS MUST BE DONE PRIOR TO THE CONCRETE POUR AND IS THE RESPONSIBILITY OF THE
SUBCONTRACTOR WHO REQUIRES THE PENETRATION OR CONCEALMENT.
2. AT EXTERIOR ICF WALLS, ALL AREAS OF ICF FOAM INSULATION ROUTED OUT FOR ELECTRICAL
CONDUIT, PLUMBING, ETC. SHALL BE SPRAY-FOAMED AND RE-INSULATED AROUND SUCH
INSTALLATION TO RETARD THERMAL TRANSMISSION.
"NO LEAD" WARNING
PLUMBING LEAD SHEET
ALL WETTED PLUMBING ITEMS FURNISHED FOR THIS
PROJECT MUST COMPLY WITH FEDERAL LAW AND
NSF 372 STANDARD ENTITLED: DRINKING WATER
SYSTEM COMPONENTS - LEAD CONTENT. THE
CONTRACTOR AND ALL SUPPLIERS MUST COMPLY
WITH THIS FEDERAL LAW REGARDLESS OF
MANUFACTURERS/PRODUCTS SPECIFIED WITHIN
THE CONSTRUCTION DOCUMENTS.
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
P-0.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
MECHANICAL
CONSTRUCTION NOTES
(APPLIES TO THIS DRAWING ONLY)
#
1
SANITARY SEWER PIPING. REFER TO CIVIL DRAWINGS FOR CONTINUATION AND
ADDITIONAL WORK. CONTRACTOR SHALL VERIFY INVERT ELEVATION AT
CONNECTION POINT PRIOR TO INSTALLATION OF PIPING TO VERIFY ADEQUATE
FALL.
STAIR
110
STORAGE
BM OFFICE
125
122
FR1
MECH./ELEC.
124
BOOK MOBILE
FD-2
FD-2
121
CCO-1
SS
SS
OWS-1
CORRIDOR
WCO-1
123
SS
FR1
WCO-1
WCO-1
CO-1
P-10
P-14
P-2
SS
P-3
TOILET
CO-1
111
SS
STAFF TOILET
1
P-4.1
(TYP.)
P-2
CCO-1
SS
SS
1
P-1
P-9
119
P-1
WCO-1
CUSTODIAL
2
P-4.1
FD-1
TP-1
(TYP.)
P-1
P-13
WCO-1
118
P-6
WORKROOM
P-7
WH-1A
P-6
114
WOMEN
CHILDREN/JUVENILE
109
107
BRANCH MNGR
WH-1B
117
SS
YOUTH PROGRAM
115
FD-1
TP-1
CO-1
FD-1
TP-1
HVAC
WCO-1
CIRCULATION
112
3
P-4.1
(TYP.)
FS-2
TP-1
P-6
MEN
P-6
SS
116
P-1
SS
FD-1
TP-1
P-1
BOOK RETURN
MECH./ELEC.
102
BM OFFICE
ELECTRICAL
PLUMBING
P-5
122
124
P-2
WCO-1
YOUNG ADULTS
108
COLLECTIONS
106
FR1
VESTIBULE
101
CORRIDOR
123
STAIR
104
FR1
PROJECT
NORTH
ELEV.
ENLARGED FLOOR PLAN
103
SCALE: 1/4" = 1'-0"
SP-1
10
P-4.1
FR1
EQUIP.
105
11
P-4.1
CLASSIFIED ASSEMBLY LEGEND
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
SANITARY SEWER FIRST FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
P-1.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
MECHANICAL
CONSTRUCTION NOTES
(APPLIES TO THIS DRAWING ONLY)
REF.
#
LOCATE OPEN RECEPTACLE TO COORDINATE WITH DRAIN LOCATION OF UNDER
COUNTER DISHWASHER SO NOT TO INTERFERE WITH INSTALLATION OF
DISHWASHER.
3
COORDINATE LOCATION OF FLOOR SINK WITH HVAC, PLUMBING, AND
STRUCTURAL.
TECH LAB
220
(OPEN TO BELOW)
SS
HVAC
FS-2
TP-1
MDF
221
ELECTRICAL
DW
MECH/ELEC
222
SS
FR1
2
OR-1
P-15
BREAK ROOM OR-2
223
2
DROP SANITARY SEWER PIPING IN CHASE. SEE DRAWING P-1.1 FOR
CONTINUATION. COORDINATE WITH STRUCTURAL.
HVAC
STAIR
110
1
3
OR-1
CO-1
CORRIDOR
225
CO-1
SS
P-2
VESTIBULE
212
1
P-4.1
P-2
FILES
224
P-9
P-1
(TYP.)
P-2
STAFF TOILET
219
BOOK KEEPER
211
1
P-9
P-1
SS
FR1
WCO-1
FAMILY
218
RESEARCH
213
P-1
WCO-1
COMPUTER LAB
214
FD-1
TP-1
P-6
P-6
P-11
FD-1
TP-1
DIRECTOR
210
WOMEN
216
MAKER
215
MEN
217
P-6
P-6
P-5
P-4
A/V-STACKS
209
FD-1
TP-1
P-1
WB-1
CORRIDOR
201
WCO-1
P-7
D
3
P-4.1
(TYP.)
P-12
FS-1
W
P-13
P-2
UTILITY
202
OR-2
CO-1
ICE
REF.
DW
SS
GT-1
P-9
MTG. STORAGE
207
STUDY
208
CO-1
OR-2
2
CATER
206
FD-1
TP-1
P-8
STUDY
205
FD-1
TP-1
FR1
FR1
STORAGE
203A
MEETING ROOM B
204
STAIR
104
MEETING ROOM A
203
CLASSIFIED ASSEMBLY LEGEND
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
SANITARY SEWER SECOND FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
P-1.2
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
MECHANICAL
CONSTRUCTION NOTES
(APPLIES TO THIS DRAWING ONLY)
#
STAIR
7
110
STORAGE
BM OFFICE
125
FR1
122
FR1
1
DOMESTIC WATER LINE. SEE CIVIL DRAWINGS FOR CONTINUATION.
2
DO NOT INSTALL PIPING OVER ELECTRICAL PANELS (TYP.).
3
INSTALL ALL ISOLATION VALVES ABOVE LAY-IN CEILINGS OR IN ACCESSIBLE
LOCATIONS (TYP.).
4
INSTALL ALL TRAP PRIMERS IN ACCESSIBLE LOCATIONS FOR MAINTENANCE
PURPOSES (TYP.).
5
ROUTE PIPING ABOVE LAY-IN CEILING. COORDINATE WITH LIGHT FIXTURES,
DUCTWORK, STRUCTURE, ETC. (TYP.)
6
DO NOT ROUTE WATER LINES IN OR ABOVE ELEVATOR 103.
7
DO NOT ROUTE WATER LINES IN OR ABOVE STAIRWELLS 104 AND 110.
8
DOMESTIC COLD WATER PIPING FOR CONNECTION TO HVAC FILL LINE SYSTEM.
COORDINATE LOCATION OF BACKFLOW PREVENTER WITH HVAC PIPING
CONTRACTOR.
9
ROUTE GAS PIPING AS CLOSE AS POSSIBLE TO THE WALL.
10
ROUTE DOMESTIC HOT WATER PIPING AS HIGH AS POSSIBLE AND PENETRATE
STRUCTURE INTO MECH/ELEC ROOM 222 ON SECOND FLOOR, SEE DRAWING P1.4
FOR CONTINUATION.
11
ROUTE DOMESTIC COLD WATER PIPING AS HIGH AS POSSIBLE AND PENETRATE
STRUCTURE INTO MECH/ELEC ROOM 222 ON SECOND FLOOR, SEE DRAWING P1.4
FOR CONTINUATION.
12
ROUTE DOMESTIC HOT WATER RECIRCULATION PIPING AS HIGH AS POSSIBLE AND
PENETRATE STRUCTURE INTO MECH/ELEC ROOM 222 ON SECOND FLOOR, SEE
DRAWING P1.4 FOR CONTINUATION.
13
CORE DRILL HOLE THROUGH BASEMENT WALL AND INSTALL LINKSEAL
MECHANICAL SLEEVE SEAL.
14
ROUTE DOMESTIC COLD AND HOT WATER TO EACH FIXTURE OR SPECIALTY ITEM
SHOWN IN COMMON WALL.
BOILER
124
BOOK MOBILE
121
3/4"
HB-2
CORRIDOR
5
123
2"
1-1/4"
2"
FR1
P-2
1"
3/4"
1"
STAFF TOILET
P-3
1/2"
14
(TYP.)
P-1
P-9
119
TOILET
P-1
111
1/2"
CUSTODIAL
118
P-13 1-1/2"
3/4"
1/2"
FD-1
TP-1
P-1
P-6
3/4"
WORKROOM
P-7
CHILDREN/JUVENILE
109
107
9
P-6
114
YOUTH PROGRAM
1
4
P-4.1
WOMEN
(TYP.)
117
BRANCH MNGR
3"
115
FWH-1
3/4"
116
P-5
P-1
(TYP.)
16
P-4.1
BFP-1
PRV-1
FD-1
TP-1
P-1
1-1/2"
WH-1B
ET-1
13
P-4.1
CP-1
2"HVAC
FD-1
TP-1
1-1/2"
1-1/2"
1/2"
1/2"
15
P-4.1
BFP-2
2
8
(TYP.)
BOOK RETURN
HB-1
12
P-4.1
1/2"
120
FS-2
TP-1
MEN
112
14
P-4.1
B
1B
2-1/2"
P-6
P-6
CIRCULATION
B
1A
2"
3
P-4.1
(TYP.)
2-1/2"
G
2"
G
1/2"
3/4"
WH-1A
4
BOILER
102
BM OFFICE
ELECTRICAL
1"
P-14
P-2
W
P-10
HB-1
PLUMBING
IMB-1
122
124
P-2
1-1/2"
YOUNG ADULTS
108
1/2"
2"
FR1
COLLECTIONS
106
3
10
(TYP.)
12
11
VESTIBULE
101
CORRIDOR
1-1/4"
123
2"
1/2"
STAIR
104
7
FR1
PROJECT
NORTH
ELEV.
103
ENLARGED FLOOR PLAN
6
SCALE: 1/4" = 1'-0"
FR1
EQUIP.
105
3/4"
FWH-1
CLASSIFIED ASSEMBLY LEGEND
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
PLUMBING PIPING FIRST FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
P-1.3
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
2
G
G
1
03/01/2018
MECHANICAL
CONSTRUCTION NOTES
8
(APPLIES TO THIS DRAWING ONLY)
#
G
G
FM
FW
W
3"
9
FWH-1
FWH-1
IMB-1
3/4"
3/4"
HVAC
STAIR
110
REF.
10
P-15
DOMESTIC WATER LINE. SEE CIVIL DRAWINGS FOR CONTINUATION.
2
NATURAL GAS LINE. SEE CIVIL DRAWINGS FOR CONTINUATION.
3
INSTALL ALL ISOLATION VALVES ABOVE LAY-IN CEILINGS OR IN ACCESSIBLE
LOCATIONS (TYP.).
4
INSTALL ALL TRAP PRIMERS IN ACCESSIBLE LOCATIONS FOR MAINTENANCE
PURPOSES (TYP.).
5
ROUTE SEAMLESS NO-JOINT PIPING BELOW FLOOR SLAB (TYP.).
6
ROUTE DOMESTIC HOT WATER PIPING, DOMESTIC COLD WATER PIPING, AND HOT
WATER RECIRCULATION PIPING ABOVE LAY-IN CEILING (TYP.).
7
DO NOT INSTALL PIPING OVER ELECTRICAL PANELS (TYP.).
8
SEE DETAIL ON P-4.1. SEE CIVIL DRAWING FOR CONTINUATION AND ADDITIONAL
WORK.
9
ROUTE ALONG AND SUPPORT ON WALL.
10
RISE AND INSTALL LOW AS POSSIBLE INTO MECH/ELEC 222.
11
ROUTE DOMESTIC COLD AND HOT WATER TO EACH FIXTURE OR SPECIALTY ITEM
SHOWN IN COMMON WALL.
TECH LAB
220
(OPEN TO BELOW)
ELECTRICAL
FR1
MECH/ELEC
222
HVAC
DW
IMB-1
BREAK ROOM
223
1
1-1/2"
2"
1/2"
3
(TYP.)
7
MDF
221
7
11
CORRIDOR
225
6
2"
2"
(TYP.)
1-1/2"
P-2
1/2"
FR1
P-9
P-1
VESTIBULE
212
P-2
1-1/2"
3/4"
P-9
STAFF TOILET
219
BOOK KEEPER
211
HB-1
P-2
FILES
224
P-1
FAMILY
218
RESEARCH
213
FD-1
TP-1
P-1
P-6
COMPUTER LAB
214
3/4"
P-6
P-11
FD-1
TP-1
DIRECTOR
210
WOMEN
216
4
(TYP.)
MAKER
215
1-1/4"
1/2"
1-1/2"
P-6
5
(TYP.)
3/4"
P-6
3
P-4.1
(TYP.)
P-5
1-1/2"
P-4
14
P-4.1
A/V-STACKS
209
MEN
217
FD-1
TP-1
P-1
(TYP.)
WB-1
HB-1
P-2
CORRIDOR
201
IMB-1
FWH-1
OR-1
ICE
P-12
FS-1
REF.
W
P-13
D
3/4"
3/4"
1"
UTILITY
202
P-7
1-1/2"
IMB-1
1"
1/2"
DW
3/4"
P-9
MTG. STORAGE
207
STUDY
208
FD-1
TP-1
CATER
206
P-8
STUDY
205
FD-1
TP-1
FR1
FR1
STORAGE
203A
MEETING ROOM B
204
STAIR
104
MEETING ROOM A
203
CLASSIFIED ASSEMBLY LEGEND
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
PLUMBING PIPING SECOND FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
P-1.4
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
4"
VT
R
03/01/2018
4"
4"
4"
2"
2"
VT
R
FR
IN OM O
BO W
OK S-1
MO
BIL
3"
E
2" -1
OR
2"
4"
2"
2"
5
P-1
EC
L
E
/
CH3
E
M 22
2"
FS
TP - 2
-1
EC
L
E
H/
C
ME 222
-2
R
O
2"
F
MD1
22
2"
OR
-1
4"
2
P-
CO
4"
-1
SS
SS
4"
4"
N
4"
4"
SS
SS
4"
SS
4"
-2
4"
-1
CO
2" P-1
4"
SS
2"
4"
4"
4"
-1
FD-1
TP
4"
2" P-1
2"
1-1
P
/2"
9
P-
2"TP-2
ILE
TO
F
AF
ST 219
1-1
Y
9 /2" MIL
P
FA15
2
2"
4"
SS
-1 2"
O
/
WC 1-1
/2"
6
1
4"
P
1
6
P2"
4"
2"
2"
2"
4"
4"
4"
4"
1-1
/2"
1
1
P-6
P-6
FD
TP -1
-1
4"
2"
ER
P-
2"
2"
11
K
MA15
2
4"
4"
2"
2"
1-1
2"
-1
FD-1
TP
4"
2" P-1
4"
RO
CH UT
AS E IN
E P
LU
RO
AL UTE
ON EX
RO
G W PO
CH UT
AL SED
AS E IN
L
E P
AS
LU
1
C
MB
L
O
O
ING
SE
CC
4"
4"
FD
4"
FD
4"
4"
2"
2"
-1
FD-1
TP
4"
3"
C
4" 1
4"
OC
W
2
P-
-2
FS-1
TP
2"
4"
SS
4"
2"
/
1
1-
T
1-1
LE
I
/2"
TO11
2" 1 2"
P3
4"
WC CO1
O1
/2"
1
1
P- 1
0
C
P-9
4"
1
1-1
ET
4"
2"
4"
1
P-
4"
1-1
1
OC
W
2"
4"
2"
2"
OG
R
P
TH 9
U
YO 10
SS
M
RA
TY
ILI
T
U 02
2
-1
4"
SS
/2
1
1
6
P-
-1
FD-1
TP
"
/2"
1
1
6
P-
4"
-1
CO
2"
2"
2"
9
P-
4"
2"
WC
O
4"
/
1-1
-1
1/
-6 1-
4"
N
ME6
11
2"
2"
P
6
P-
2"
2"
4"
2"
/2"
1
1
4
P-
-1
FD-1
TP
4"
2" P-1
4"
SS
2"
2"
4"
P-1
4" P-2
4"
P14
P-1
3
O
WC
G
VEREA
NT SE
2"
PIPTR 2"
"
CO
2
/
INGAP
1
-1
1
F
2"
FILTOW
PIPTIN CO
2"
IN G NT
2"
G
V
2"
ENRO
PO
T L
R7
2
3"
4"
"
P-1
2
2"
FS 2
2" SINK
GT
-1
-1
VE
OR
1
NT
D
-2
F -1
"
2
TP
R
-8
4"
TE
P
A
C 06
4"
2
2"
4"
2"
P-7
/2"
1
1
1
OC
C
W
4"
/2"
1
P-
4"
SS
2" L
"
OI
2
/
T
1
SS
4" TAFF
1 1 3 P-1
O
3
"
S 119
4"
WC
IAL
D
TO
S
CU 118
2
24"
"
P-
/2"
P-
2"
2"
4"
CO
CO
SL
FOEE
UNVE
DATH
TIORU
OR
NW
ALBEL
L O
SS D-1 MEN
-1O 7
4"FPW
T 11
2"
4"
4"
1
4"
2"
4"
1
4"
.
EC
L
E
H./
C
ME124
SS
4"
OC
W
4" P-2
3"
1
-1
FD-1
TP
3"
-1
4"
4"
SL
FOEE
UNVE
DATH
-1 ILE
S
TIORU
B
W
O
OR
O
NW
M
K
ALBEL
O 1
O
L O
2
B 1
W
4"
-2
WB
2"
-2
4"
2"
4"
4"
ING
/2"
3"
4"
MB
2"
2"
SS
ING
/2"
1-1
/
2"
4"
/2"
1
1
5
/2"
1
P1
4
P-
LU
MB
1-1
N
ME7
21
/2"
2"
-1
O
"
WC 4
RO
CH UT
AS E IN
E P
2" P-1
4"
4"
2"
ME
O
W 16
2
4"
4"
1
OC
W
PLUMBING DWV DIAGRAM
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
P-3.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
INSTALL FLUSH WITH
FINISHED FLOOR
CLEANOUT
REFER TO PLUMBING SCHEDULE
FOR REQUIREMENTS
MAY EXTEND AS
WASTE OR VENT
FOR WALL CONST.
REF. ARCH. DWGS.
1/2" POSITIVE WASH
CLEANOUT
REFER TO PLUMBING DRAWINGS
FOR REQUIREMENTS
CONCRETE COLLAR
(MIN. WIDTH 18")
1/2" SUPPLY PIPING
(INSULATE)
WALL CLEANOUT.
REFER TO PLUMBING SCHEDULE
FOR REQUIREMENTS
POLISHED S.S.
ACCESS COVER W/
COUNTERSUNK SCREW
CLEANOUT TEE
BALL VALVE
(INSULATE)
UNION
TRAP PRIMER
WATER SUPPLY PIPING
(INSULATE)
SEE PLAN FOR SIZE
GRADE
03/01/2018
DEPTH VARIES
DEPTH VARIES
NOTE:
REFER TO DWV DIAGRAM FOR PIPE SIZES.
2.
USE DOUBLE TEE WHERE POSSIBLE.
3.
COORDINATE WITH ARCHITECTURAL
DRAWINGS FOR FLOOR FINISH TO VERIFY
CLEANOUT ELEVATION.
FIN. FLOOR
1. TAKE OFF FROM TOP OF PIPE TO LIMIT
SOLID PARTICLES ENTERING TRAP PRIMER
DISTRIBUTION UNIT
(IF REQ'D.)
SANT. DRAIN
2. TAKE OFF SHALL BE MIN. 12" ABOVE
FLOOD LEVEL RIM OF FLOOR DRAIN
CLEANOUT DETAIL
1
2
P-1.1
NO SCALE
SANT. DRAIN
TEST TEE
1.
REFER TO DWV DIAGRAM.
2.
CLEANTOUT INSTALLED IN IMPROVED SURFACES
SHALL BE SUITABLE FOR VEHICLE TRAFFIC.
3.
USE DOUBLE TEE WHERE POSSIBLE.
P-1.1
P-1.2
NO SCALE
3
VAPOR BARRIER
U-BOLT OR
UNI-STRUT CLAMP
INSULATION
CONTINUOUS THRU
HANGER.
INSULATION SADDLE
NO SCALE
PIPE INSULATION
OR HDPE TUBING
3. INSULATION SADDLE SHALL BE USED TO SPREAD
FORCE OVER A LARGE AREA OF THE INSULATION
TO PREVENT CRUSHING.
VALVE
BRANCH PIPE
ANGLE IRON OR OTHER
APPROPRIATE SUPPORT
PIPE MAIN
SUPPORT ROD
LEC
IBR
I
X
E
E
FLOMON
"
8
3/ ASTATI
ELSUL
IN
4. THE INSULATION SHALL BE CONTINUOUS THROUGH
HANGER.
LOCK NUT
5. THE VAPOR BARRIER SHALL BE CONTINUOUS THROUGH
HANGER.
NUT
6. REFER TO DRAWINGS AND SPECIFICATIONS FOR PIPING
MATERIAL AND SIZE.
1.
TAKE OFF FROM TOP OF PIPE TO LIMIT SOLID
PARTICLES AND TO RISE ABOVE PARALLEL PIPE.
CPVC AND PVC VALVES ARE NOT ACCEPTABLE.
3.
VALVE STEMS SHALL BE INSTALLED ABOVE CENTER
LINE OF PIPE.
PIPE TAKE OFF DETAIL
5
INSULATION
CONTINUOUS THRU
HANGER.
CLEVIS HANGER
VAPOR BARRIER
INSULATION SADDLE
5. TRAP PRIMER SHALL BE ACCESSIBLE FOR
MAINTENANCE. IF THE ABOVE LOCATIONS ARE
NOT PRACTICAL, LOCATE PRIMER IN AN
INTERIOR WALL AND FURNISH AND INSTALL
A PAINTABLE STEEL, KEY LOCKED ACCESS
DOOR WITH FRAME.
TRAP PRIMER DETAIL
NO SCALE
PROTECT PIPE INSULATION AFF WITH
PVC INSULATION JACKET
N
O
I
R
ISE C UNGHT
R
E TRI TI
P
I
P EC TER
L A
DIE L W
A
SE
OR AB
O
U
FL L. SL
R
.
TH
FIN C. F
E
V
N
EE AB
CO
L
C SR SL
V
P OO
FL
RD
A
H E
L' PIPOR)
'
PE ER LO
TY PPVE F
COBO
(A
FTING LAB)
O
S B
K' TU C. S
'
PEPERCON
Y
T P R
CONDE
(U
7. REFER TO SPECIFICATION FOR INSULATION MATERIAL
AND SIZE.
8. FOR LARGE SIZE PIPE, SUPPORT SHOES MAY BE
REQUIRED. SEE SPECIFICATIONS.
2.
MECHANICAL ROOMS
JANITOR CLOSETS/ROOMS
ABOVE ACCESSIBLE CEILINGS WHEN HEATED
IN ACCESSIBLE PLUMBING CHASES
FROM GAS METER
GAS PLUG WITH
SQUARE HEAD
SEE PLANS FOR
PIPE SIZE
UNION
NOTES:
THRU BOLT
4
P-1.3
P-1.4
MIN. 6"
2. COPPER PIPING SHALL BE ISOLATED FROM CONTACT
WITH HANGER.
A.
B.
C.
D.
WALL CLEANOUT DETAIL
CONC. FLOOR SLAB
1. THIS METHOD FOR PIPE SUPPORT AND INSULATION
PROTECTION SHALL BE USED UNLESS SPECIFICALLY
APPROVED OTHERWISE.
4. PRIORITY OF TRAP PRIMER LOCATION
(IN ORDER)
1/2" MPT
ADAPT.
NOTE:
STACK CLEANOUT IS THE SAME
EXCEPT THE PIPE IS NOT IN THE
WALL AND THE ACCESS COVER
IS NOT NEEDED
FLOW
COMBINATION TEST TEE AND CLEANOUT DETAIL
3. ALWAYS INSTALL IN ACCESSIBLE AREA
1/2" PEX TUBING
TO FLOOR DRAIN(S)
AND/OR OPEN RECEPT.
(INSULATION NOT REQ'D.)
1/8" BEND
NOTE:
NOTES:
P-1.3
P-1.4
TRAP PRIMER NOTES:
TWO-WAY TEE
1.
P-1.1
P-1.2
UNIFORM
HEIGHT
18"
MIN. WHERE
POSSIBLE
ATTEMPT TO MAINTAIN
9. WHERE INSULATION IS REQUIRED, INSTALL CORRECT
SIZE HANGER FOR PIPE AND INSULATION THICKNESS
REQUIREMENTS.
TO EQUIPMENT
CHANGE TYPES OF COPPER AT
DIELECTRIC UNIONS
6" DIRT LEG
CONTRACTOR MAY SUBSTITUTE HDPE TUBING
FOR INSULATION UNDER FLOOR SLAB
THREADED CAP
INSTALL WHERE REMOVABLE FOR CLEANING
10. WHERE INSULATION IS NOT REQUIRED, INSTALL
CORRECT SIZE HANGER FOR PIPE.
NO SCALE
P-1.3
P-1.4
6
PLUMBING PIPE SUPPORT DETAIL
7
P-1.3
P-1.4
NO SCALE
DOMESTIC WATER PIPE
UNDER FLOOR SLAB DETAIL (COPPER)
GAS CONNECTION DETAIL
8
P-1.1
NO SCALE
NO SCALE
BY UTILITY COMPANY
BY CONTRACTOR
UNION (TYP.)
PAINT METER AND PIPE
AFTER INSTALLATION
FIN. FL.
THREADED CONNECTION FOR
PRESSURE GAUGE. INSTALL PLUG
T.O.C.
SUBMERSIBLE PUMP
ZOELLER PUMP CO.
"MIGHTY-MATE" MODEL 57
AUTOMATIC FLOAT OPERATED
ALL CAST IRON CONSTRUCTION
115V/1∅, 0.3 HP, 35 GPM
@ 10 TDH
REGULATOR
TO 1/2 PSIG
GAS PLUG VALVE
WITH SQUARE HEAD
CAST BRONZE DOWNSPOUT
NOZZLE TERMINATION WITH
POLISHED CHROME FINISH
UNION
GAS PIPING
MANUAL GAS SUPPLY
LINE SHUT-OFF VALVE
ROUTE RELIEF VALVE
PIPING TO OPEN
RECEPTACLE OR FLOOR
DRAIN
ROUTE PIPING CONCEALED IN WALL
OR CHASE.
CONTRACTOR SHALL FURNISH
AND PLACE CONC. SPLASH
BLOCK
UNION
EXPANSION TANK
HOT WATER OUT
COPPER
CHECK VALVE
COLD WATER IN
1-1/2" C.I. PIPE
INSTALL PUMP ON
4" FRP CHANNELS
GRADE
GAS METER
PROVIDE SUMP PUMP WITH:
SKIMOIL, INC. OILSMART OIL SENSOR & PUMP
SWITCH WITH ALARM PANEL, HIGH LIQUID
ALARM SWITCH, FLOAT SWITCH, AND LEVEL
DETECTOR - REQUIRES TWO GFCI 120 VOLT
CIRCUITS ALL CAST IRON CONSTRUCTION
INVERT EL.
GAS METER DETAIL
10
P-1.1
NO SCALE
NO SCALE
COLD WATER PIPE BUILDING
DOM. WATER SYSTEM
ES
M
DO
OT
H
C
T
WA
E
IP
P
R
E
ROUTE DRAIN HOSE TO FLOOR DRAIN
SUMP PUMP PIPING TERMINATION DETAIL
TI
TANKLESS WATER HEATER DETAIL
12
P-1.3
NO SCALE
PRESSURE REGULATING VALVE
REFER TO PLUMBING SCHEDULE
FOR REQUIREMENTS.
R
TO
ING
ES
ER
M
R
D
A
A
AR
FR
HE
K
OC
NG
I
H
M
IPE
S
A
P
ED
FR
ER
T
T
A
A
W
RIC
B
D
L
)
A
F YP.
O
C
T
(
TIC
S
ME
AP
O
R
RE
D
ST
U
G
IXT
N
I
F
UR
OR
C
F
E
S
UT
O
UB
ST P.)
(TY
E
: PIP E
E
T E ID
NOCURCK SR
SE BA ADE
TO
HE
F
O
6" DIRT LEG
CAPPED FOR CLEAN
OUT PURPOSES
SEAL PIPE PENETRATION
11
P-1.1
D
COLD WATER SUPPLY
SHUT-OFF VALVE
DRAIN VALVE ROUTE TO
OPEN RECEPTACLE OR
FLOOR DRAIN
PVC
FROM ELEVATOR SUMP PUMP.
REFER TO DRAWINGS FOR SIZE.
SUMP PUMP DETAIL
U
ST
MIXED WATER PIPE TO
WATER HEATER INLET
UNION (TYP.)
CHECK VALVE
ROUTE AND SUPPORT ALONG
WALL. SEE PLAN.
BALL VALVE
(TYP.)
TANKLESS
WATER
HEATER
RELIEF VALVE
TERMINATE PIPING AT
SPLASH BLOCK AT GRADE
2" PVC
DISCHARGE LINE
BEDDED IN DGA
PAINTED CARBON
STEEL PIPE
WALL.
REFER TO ARCHITECTURAL DRAWINGS
FOR CONSTRUCTION DETAIL
12"
CARBON STEEL
POLYETHYLENE
SEE ELECTRICAL
FOR POWER
REQUIREMENTS
ROUTE FLUE VENT PIPING
TO OUTDOORS PER
MANUFACTURER'S
RECOMMENDATIONS
1
2"
METER AND SERVICE LINE
INSTALLED BY UTILITY COMPANY
9
P-1.1
ROUTE COMBUSTION AIR
INTAKE PIPING FROM
OUTDOORS PER
MANUFACTURER'S
RECOMMENDATIONS
GRATE COVER
PRESSURE
GAGE
(TYP.)
NO SCALE
TO BUILDING
DISTRIBUTION
BACKFLOW PREVENTER
REFER TO PLUMBING SCHEDULE
FOR REQUIREMENTS
STRAINER
MAIN VALVE
DOMESTIC WATER
TO PIPING SYSTEM
DOMESTIC
WATER SERVICE
DIELECTRIC UNION
TEMPERATURE GAUGE
(TYP.)
SEAL WATER TIGHT
CHECK VALVE (TYP.)
SLEEVE
PRESSURE GAUGE
(TYP.)
NOTE:
THERMOMETER
E
INGPIP
M
RAPER
F
& OP
S
C
UD W/
T
L SACT
A
ET ONT
M
C
AT IN
:
H
TE T ME
NO URE CO
S T
AS NO
DO
CHECK VALVE
(TYP.)
UNION
(TYP.)
HOT WATER PIPE
CIRCULATION RETURN
CIRCULATING PUMP
CP-1 REFER TO
PLUMBING SCHEDULE
STRAINER
13
P-1.3
3
/4"
CIRCULATING PUMP PIPING DETAIL
NO SCALE
WATER BALANCING
VALVE (TYP.)
P-1.3
P-1.4
14
FIXTURE SUPPLY DETAIL
NO SCALE
DOMESTIC WATER SERVICE
16
P-1.3
1.
CHANGE TYPES OF PIPING AT DIELECTRIC UNION.
2.
CLEARANCE FROM BACKFLOW PREVENTER TO FIN. FLOOR
SHALL BE BETWEEN 24" AND 30".
DOMESTIC WATER SERVICE DETAIL
NO SCALE
PLUMBING DETAILS
MARCUM
15
P-1.3
BRANCHLINE RECIRCULATION DETAIL
NO SCALE
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
P-4.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
VENTILATING FAN SCHEDULE
PHYSICAL DATA
MARK
MFG.
PERFORMANCE DATA
MODEL /
TYPE
AREA SERVED
HVAC LEGEND
SIZE
APPROX.
UNIT
WEIGHT
(LBS.)
MOUNTING
RATED
AIRFLOW
(CFM)
ESP
(IN. H2O)
DRIVE
UNIT OPERATION CONTROL
FAN
SPEED
(RPM)
MOTOR
TYPE
SONES
SWITCH
BRKR
DDC
ELECTRICAL DATA
OCC.
HP
WATTS
VOLTAGE /
PHASE
SYMBOL
REMARKS AND
ACCESSORIES
1.
DESCRIPTION
NEW RECT. SHEETMETAL DUCTWORK:
FIRST FIG. WIDTH, SECOND FIG. DEPTH
2.
NEW ROUND RIGID SHEETMETAL DUCTWORK
EF-1
GREENHECK
111 TOILET
CSP
A290
30
INLINE
70
0.75
DIRECT
978
ODP
2.5
EF-2
GREENHECK
121 BOOK MOBILE
CSP
A190
20
INLINE
140
0.25
DIRECT
1,193
ODP
0.9
EF-3
GREENHECK
119 STAFF TOILET
SP
A90
20
CEILING
70
0.25
DIRECT
900
ODP
0.7
EF-4
GREENHECK
118 CUSTODIAL
SP
B80
15
CEILING
60
0.25
DIRECT
887
ODP
0.9
EF-5
GREENHECK
117 WOMEN
SP
A410
40
CEILING
280
0.25
DIRECT
873
ODP
1.5
EF-6
GREENHECK
116 MEN
SP
A410
40
CEILING
280
0.25
DIRECT
873
ODP
1.5
EF-7
GREENHECK
223 BREAKROOM
CSP
B150
20
INLINE
100
0.75
DIRECT
942
ODP
1.5
EF-8
GREENHECK
219 STAFF TOILET
SP
A90
20
CEILING
70
0.25
DIRECT
900
ODP
0.7
EF-9
GREENHECK
218 FAMILY
SP
A90
20
CEILING
70
0.25
DIRECT
900
ODP
0.7
EF-10
GREENHECK
215 MAKER
CSP
A700
40
CEILING
340
0.50
DIRECT
806
ODP
0.6
---
59
115V / 1Ø
1-6,10-11
---
31
115V / 1Ø
1-6,8-9
---
15
115V / 1Ø
1-7,10
---
17
115V / 1Ø
1-7,10
X
---
121
115V / 1Ø
1-7,10
X
---
121
115V / 1Ø
1-7,10
---
99
115V / 1Ø
1-6,9-11
X
---
15
115V / 1Ø
1-7,10
X
---
15
115V / 1Ø
1-7,10
---
104
115V / 1Ø
1-6,10-11
X
X
X
X
X
X
EF-11
GREENHECK
216 WOMEN
SP
A410
40
CEILING
280
0.25
DIRECT
873
ODP
1.5
X
---
121
115V / 1Ø
1-7,10
EF-12
GREENHECK
217 MEN
SP
A410
40
CEILING
280
0.25
DIRECT
873
ODP
1.5
X
---
121
115V / 1Ø
1-7,10
EF-13
GREENHECK
202 UTILITY
SP
B150
15
CEILING
140
0.25
DIRECT
959
ODP
2.0
X
---
128
115V / 1Ø
1-7,10
EF-14
GREENHECK
206 CATER
SP
A410
40
CEILING
275
0.25
DIRECT
864
ODP
1.5
X
---
121
115V / 1Ø
1-7,10
REF-15
GREENHECK
MECH/ELEC 222
QEID
24
240
SUSPENDED
9,650
1.50
DIRECT
1,170
TEFC
22.0
5
---
208V / 3Ø
3,4,10,12-21
X
3.
NEW FLEXIBLE ROUND DUCTWORK
SUPPLY AIR DUCT (UP/DN)
RETURN AIR DUCT (UP/DN)
EXHAUST AIR DUCT (UP/DN)
4.
CEILING SUPPLY AIR DIFFUSER
PROVIDE UNIT WITH FACTORY WIRED, DISCONNECT.
2.
PROVIDE UNIT WITH SOLID-STATE FAN SPEED CONTROL. COORDINATE INSTALLATION OF FIELD INSTALLED SPEED CONTROLLERS WITH ELECTRICAL CONTRACTOR.
3.
PROVIDE UNIT WITH VIBRATION ISOLATION KIT.
4.
PROVIDE UNIT WITH THERMAL OVERLOAD PROTECTION.
5.
PROVIDE UNIT WITH ROUND DUCT CONNECTOR.
6.
PROVIDE UNIT WITH GRAVITY BACKDRAFT DAMPER.
7.
PROVIDE UNIT WITH ALUMINUM INTAKE GRILLE WITH WHITE ENAMEL FINISH.
8.
INSTALL 1/2" X 1/2" EXPANDED METAL SCREEN ON INTAKE TO FAN.
CONCEAL ALL DUCTWORK, PIPING, ETC. IN CEILING AND/OR WALL SPACES (UNLESS NOTED
OTHERWISE). PROVIDE ALL NECESSARY ACCESS DOORS IN INACCESSIBLE CEILINGS TO ALLOW
ACCESS FOR MANUAL VOLUME DAMPERS, VALVES, CONTROL COMPONENTS, ETC.
6.
SLEEVE ALL DUCTWORK, PIPING, VENTS, ETC. THROUGH NEW ROOF, FLOOR, AND/OR WALLS.
7.
FLASH AND SEAL ALL ROOF, FLOOR, AND WALL PENETRATIONS.
CEILING EXHAUST AIR GRILLE
8.
SQUARE TO ROUND TRANSITION
A. PAD SHALL BE 4" THICK (MINIMUM) BUT SUITABLE HEIGHT FOR SYSTEM OPERATION AND PROPER
CONDENSATE DRAINAGE. COORDINATE PAD HEIGHT WITH EQUIPMENT RAIL(S).
PROVIDE UNIT WITH CAST ALUMINUM BRICK VENT TERMINATION (GREENHECK MODEL BVC OR EQUAL) WITH 3-COAT, FACTORY APPLIED KYNAR FINISH IN CUSTOM COLOR TO BE SELECTED BY THE ARCHITECT. FURNISH BRICK VENT WITH INTEGRAL
BACKDRAFT DAMPER AND INSECT SCREEN.
10. INTERLOCK UNIT WITH CONTROL DAMPER. REFER TO CONTROL DAMPER SCHEDULE AND SEQUENCE OF OPERATIONS FOR HVAC CONTROLS FOR ADDITIONAL INFORMATION.
11. SEE GRILLE AND DIFFUSER SCHEDULE FOR EXHAUST GRILLE SPECIFICATIONS.
12. PROVIDE UNIT WITH LIFTING LUGS AND SLIP-FIT INLET AND OUTLET COLLARS.
13. PROVIDE UNIT WITH COATED AND PHOSPHATIZED STRUCTURAL PARTS.
14. PROVIDE UNIT WITH CONTINUOUSLY WELDED STEEL HOUSING.
15. PROVIDE UNIT WITH PREMIUM EFFICIENT MOTOR THAT IS FULLY MODULATING AND HAS CLASS B OR GREATER INSULATION.
16. PROVIDE UNIT WITH BOLTED ACCESS DOOR.
17. PROVIDE UNIT WITH SOUND ATTENUATION OPTIONS (SUCH AS INLET AND OUTLET SILENCERS).
18. PROVIDE ALL NECESSARY HARDWARE TO MOUNT FAN TO STRUCTURE. HARDWARE SHALL INCLUDE ISOLATION SPRINGS.
19. ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL DISCONNECT SWITCH.
20. PROVIDE UNIT WITH 3 PHASE ELECTRICAL PROTECTION FOR MOTOR.
21. TEMPERATURE CONTROLS CONTRACTOR SHALL SUPPLY VARIABLE FREQUENCY DRIVES FOR UNITS.
UNIT OPERATION CONTROL:
SWITCH - UNIT SHALL BE CONTROLLED BY INDEPENDENT SWITCH. ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL SWITCH.
OCC. - UNIT SHALL BE CONTROLLED BY ZONE LIGHT CONTROL. COORDINATE INTERCONNECTION OF FAN TO LIGHTING POWER CIRCUIT WITH THE ELECTRICAL CONTRACTOR.
BRKR - UNIT SHALL BE CONTROLLED BY A DEDICATED SWITCH RATED BREAKER. ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL BREAKER.
DDC - FAN SHALL BE CONTROLLED BY TEMPERATURE CONTROL CONTRACTOR.
COOK, GREENHECK, PENNBARRY, TWIN CITY, OR APPROVED EQUAL
SINGLE DUCT AIR TERMINAL UNIT WITH HOT WATER HEAT SCHEDULE
MANUFACT.
VAV-1
ETI
VAV-2
ETI
VAV-3
ETI
VAV-4
ETI
VAV-5
ETI
VAV-6
ETI
VAV-7
ETI
VAV-8
ETI
VAV-9
ETI
VAV-10
ETI
VAV-11
ETI
VAV-12
ETI
VAV-13
ETI
VAV-14
ETI
VAV-15
ETI
VAV-16
ETI
VAV-17
ETI
VAV-18
ETI
VAV-19
ETI
VAV-20
ETI
VAV-21
ETI
VAV-22
ETI
VAV-23
ETI
VAV-24
ETI
MODEL
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SDR
SIZE
08
16
16
12
10
10
12
04
10
06
14
12
08
08
16
16
06
14
10
08
12
10
06
08
INLET
DIAMETER
(INCHES)
OUTLET
SIZE
(IN.)
7-7/8
15-7/8
15-7/8
11-7/8
9-7/8
9-7/8
11-7/8
3-7/8
9-7/8
5-7/8
13-7/8
11-7/8
7-7/8
7-7/8
15-7/8
15-7/8
5-7/8
13-7/8
9-7/8
7-7/8
11-7/8
9-7/8
5-7/8
7-7/8
12 X10
24 X 17-1/2
24 X 17-1/2
CFM
PRESSURE
DROP
ACROSS
MAX
AIRFLOW
(IN WC)
MAX
MIN
580
175
0.34
2,940
880
0.64
2,800
840
0.59
16 X 15
14 X 12-1/2
14 X 12-1/2
1,400
420
0.47
690
207
0.17
1,000
300
0.45
16 X 15
10 X 10
14 X 12-1/2
800
240
0.13
150
45
0.04
1,015
305
0.46
450
135
0.30
1,200
360
0.19
16 X 15
12 X10
12 X10
24 X 17-1/2
24 X 17-1/2
1,490
450
0.52
595
180
0.36
10 X 10
20 X 17-1/2
14 X 12-1/2
12 X10
16 X 15
14 X 12-1/2
10 X 10
20 X 17-1/2
10 X 10
12 X10
600
180
0.36
2,400
700
0.45
2,700
810
0.55
350
105
0.14
1,600
480
0.31
760
230
0.29
650
195
0.41
1,400
420
0.47
820
250
0.33
450
135
0.30
560
170
0.32
NC LEVELS
HOT WATER HEATING COIL
RAD.
DISCH.
CFM
MBH
<15
18
18
15
<15
16
<15
<15
16
19
<15
15
<15
16
<15
16
16
<15
<15
16
15
<15
19
<15
<15
19
16
<15
<15
<15
<15
19
<15
16
<15
<15
<15
<15
<15
15
15
<15
<15
<15
<15
<15
16
<15
348
17.1
81.8
79.5
42.1
18.5
29.7
22.8
4.1
30.0
12.9
51.4
43.8
17.4
17.6
72.4
77.8
10.0
51.4
21.2
18.6
42.1
26.1
12.9
16.7
1,764
1,680
840
414
600
480
90
609
270
960
894
357
360
1,440
1,620
210
960
456
390
840
492
270
336
THERMOSTAT
BOILER EMERGENCY STOP BUTTON
SHEETMETAL SUPPLY AIR DUCTWORK
B. STEEL REINFORCEMENT SHALL BE 6" WWF, DOWELED TO FLOOR TO PREVENT LATERAL
MOVEMENT.
C. PAD DIMENSIONS SHALL GENERALLY EXTEND 4" PAST THE OUTER MOST EDGE OF THE UNIT.
A. PAD SHALL BE 6" THICK (MINIMUM) BUT SUITABLE HEIGHT FOR GRADE/DRAINAGE CONDITIONS
AND SYSTEM OPERATION.
B. STEEL REINFORCEMENT SHALL BE 6" WWF.
E-#
L- #
SHEETMETAL RETURN AIR DUCTWORK
SHEETMETAL EXHAUST AIR DUCTWORK
SHEETMETAL OUTSIDE AIR DUCTWORK
SHEETMETAL RELIEF EXHAUST AIR DUCTWORK
HOT WATER SUPPLY PIPING
HOT WATER RETURN PIPING
CONDENSATE DRAIN PIPING
REFRIGERANT PIPING
SUPPLY AIR DIFFUSER (SEE SCHEDULE)
RETURN AIR GRILLE (SEE SCHEDULE)
EXHAUST AIR GRILLE (SEE SCHEDULE)
LOUVER (SEE SCHEDULE)
DP
DIFFERENTIAL PRESSURE TRANSMITTER
VAV
#
VARIABLE AIR VOLUME UNIT (SEE SCHEDULE)
AHU
#
AIR HANDLING UNIT (SEE SCHEDULE)
EF
#
VENTILATING FAN (SEE SCHEDULE)
IU
#
DUCTLESS SPLIT INDOOR UNIT (SEE SCHEDULE)
OU
#
EAT
(°F)
LAT
(°F)
55.0
100.3
55.0
97.8
55.0
98.6
55.0
101.2
55.0
96.2
55.0
100.6
55.0
98.9
55.0
97.4
55.0
100.4
55.0
99.1
55.0
104.3
55.0
100.1
55.0
100.0
55.0
99.9
55.0
101.3
55.0
99.3
55.0
98.8
55.0
104.3
55.0
97.8
55.0
99.0
55.0
101.2
55.0
103.9
55.0
99.1
55.0
100.7
GPM
1.66
8.44
8.04
4.02
1.98
2.87
2.30
0.43
2.91
1.29
4.59
4.28
1.71
1.72
6.89
7.75
1.63
4.59
2.18
1.87
4.02
2.35
1.29
1.61
EWT
(°F)
LWT
(°F)
H2O PD
(FT WG)
140
119
140
120
140
120
140
119
140
121
140
119
140
120
140
120
140
119
140
120
140
117
140
119
140
119
140
119
140
119
140
120
140
128
140
117
140
120
140
120
140
119
140
117
140
120
140
119
0.28
1.48
1.35
1.77
0.78
0.74
1.31
0.06
0.76
0.19
0.42
1.98
0.29
0.29
1.01
1.26
0.37
0.42
0.11
0.32
1.77
0.51
0.19
0.27
POWER
(VOLTAGE)
REMARKS AND
ACCESSORIES
DUCTLESS SPLIT OUTDOOR UNIT (SEE SCHEDULE)
ROWS
B
#
HYDRONIC HEATING BOILER (SEE SCHEDULE)
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
2
24V
SEE BELOW
3
24V
SEE BELOW
2
24V
SEE BELOW
2
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
2
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
3
24V
SEE BELOW
RA
EA
OA
REA
HWS
HWR
D
R
S-#
R-#
03/01/2018
FIRE STOP ALL PENETRATIONS THROUGH FIRE RATED ASSEMBLIES. FIRE STOPPING METHOD AND
MATERIALS SHALL BE UL LISTED.
9. SEISMICALLY SUPPORT ALL EQUIPMENT, PIPE, DUCTWORK, ETC. PER THE KENTUCKY BUILDING
CODE AND SEISMIC DESIGN CATEGORY C.
10. PLACE REINFORCED CONCRETE PADS FOR ALL FLOOR AND/OR GRADE MOUNTED EQUIPMENT.
CONCRETE SHALL HAVE A DEVELOPED STRENGTH OF 4,000 PSI AT 28 DAYS. CHAMFER ALL
EXPOSED EDGES AT 1".
INDOOR PAD INSTALLATIONS:
TURNING VANES
T
S
SA
9.
THESE PLANS ARE SCHEMATIC IN NATURE AND INDICATE THE APPROXIMATE AND GENERAL
LOCATION OF DUCTWORK, EQUIPMENT, AND/OR PIPING. COORDINATE INSTALLATION OF WORK
WITH OTHER DRAWINGS AND TRADES.
VERIFY ALL DIMENSIONS BEFORE FABRICATION AND/OR INSTALLATION.
5.
VOLUME DAMPER (VD)
1.
ALL WORK SHALL BE IN ACCORDANCE WITH THE KENTUCKY BUILDING CODE, INTERNATIONAL
MECHANICAL CODE, KENTUCKY BOILER CODE, AND OTHER LOCAL, STATE, NATIONAL
CODES/STANDARDS THAT APPLY.
CONTRACTOR SHALL BE RESPONSIBLE FOR ACQUIRING A HVAC PERMIT, COORDINATING ALL
INSPECTIONS, AND PAYING ALL ASSOCIATED FEES.
CEILING RETURN AIR GRILLE
SIDE TAKE-OFF FITTING
REMARKS AND ACCESSORIES:
MARK
HVAC NOTES
HYDRONIC CIRCULATING PUMP (SEE SCHEDULE)
BP
#
BOILER CIRCULATION PUMP (SEE SCHEDULE)
RF
#
RELIEF AIR FAN (SEE SCHEDULE)
CU
#
AIR COOLED CONDENSING UNIT (SEE SCHEDULE)
RELIEF HOOD (SEE SCHEDULE)
IH
#
INTAKE HOOD (SEE SCHEDULE)
11.
12.
13.
14.
C. AT A MINIMUM, PAD DIMENSIONS SHALL GENERALLY EXTEND 12" PAST THE OUTER MOST EDGE
OF THE UNIT.
PROVIDE ALL HVAC UNITS WITH MANUFACTURER'S START-UP AND CERTIFIED REPORT FOR
ENGINEER'S APPROVAL. INSTALLING CONTRACTOR START-UP IS NOT ACCEPTABLE.
COVER ALL OPENINGS ON AIR CONVEYANCE COMPONENTS (DUCTWORK AND/OR EQUIPMENT),
WHETHER STORED OR INSTALLED, TO PREVENT ACCUMULATION OF CONSTRUCTION DUST. AIR
CONVEYANCE SYSTEMS FOUND TO BE DUSTY SHALL BE PROFESSIONALLY CLEANED AND
CERTIFIED BY A NADCA CONTRACTOR AT THE HVAC CONTRACTOR'S EXPENSE.
STORE AND INSTALL DUCTWORK AND/OR EQUIPMENT ONLY WHERE PROTECTED FROM DIRECT
CONTACT WITH RAIN OR CONSTRUCTION WATER.
COORDINATE DUCTWORK ROUTING IN CEILING SPACES TO AVOID CONFLICTS WITH FIRE
PROTECTION, PLUMBING, SPECIAL SYSTEMS, LIGHTING, NEC CLEARANCES, ETC.
15. DUCTWORK SHALL BE GALVANIZED STEEL (UNLESS SPECIFIED OTHERWISE) AND SHALL BE
FABRICATED/INSTALLED IN ACCORDANCE WITH THE APPLICABLE MANUAL OR HANDBOOK OF THE
SHEETMETAL AND AIR CONDITIONING CONTRACTORS NATIONAL ASSOCIATION, INC. (SMACNA),
LATEST ISSUE.
16. PROVIDE 4" FLEXIBLE CONNECTIONS BETWEEN ALL HVAC UNITS AND RIGID SHEETMETAL
DUCTWORK TO STOP VIBRATION TRANSMISSION.
17. INSTALL DUAL WALL TURNING VANES IN ALL ELBOWS LOCATED DOWNSTREAM OF SUPPLY FANS
(EXAMPLES ARE SUPPLY AIR, DEDICATED OUTSIDE AIR, EXHAUST AIR BETWEEN FAN AND EXIT,
ETC.). RADIUSED ELBOWS IN RECTANGULAR DUCT ARE NOT ACCEPTABLE.
18. FURNISH AND INSTALL AUTOMATIC FIRE DAMPERS WITH APPROPRIATELY SIZED ACCESS
PANELS/DOORS AT ALL FIRE RATED ASSEMBLIES.
19. CONTINUOUSLY SEAL ALL DUCT JOINTS WITH MONECO, DUCTMATE, HARDCAST, OR APPROVED
EQUAL DUCT SEALER. ASSURE THAT DUCT SEALER IS A WATER-BASED, LOW VOC COMPOUND.
P
#
RH
#
OUTDOOR PAD INSTALLATIONS:
20. INSTALL A CONDENSATE TRAP AND DRAIN LINE FOR ALL EQUIPMENT REQUIRING A DRAIN. THE
DRAIN SIZE (AT A MINIMUM) SHALL BE EQUAL TO THE UNIT'S CONNECTION SIZE BUT IN NO CASE
SHALL BE LESS THAN 1" DIAMETER. FABRICATE TRAP TO MAINTAIN TOTAL FAN STATIC PRESSURE
PLUS 1" WC.
21. FURNISH AND INSTALL MANUAL AIR VENTS AT ALL HIGH POINTS IN THE HVAC PIPING SYSTEM.
22. INTERNALLY INSULATE RETURN/EXHAUST AIR GRILLE PLENUMS WITH 1/2" FIBERGLASS,
ANTI-MICROBIAL DUCT LINER FOR SOUND CONTROL.
23. SUPPLY AIR DUCTWORK INDICATED TO BE LINED SHALL BE INTERNALLY INSULATED WITH 1"
FIBERGLASS, ANTI-MICROBIAL DUCT LINER.
24. DUCT DIMENSIONS ARE ACTUAL SHEETMETAL SIZES AND ALLOWANCES FOR INTERNAL INSULATION
HAVE BEEN ACCOUNTED FOR.
25. EXTERNALLY INSULATE ALL SHEETMETAL DUCTWORK, TRANSITIONS, TAKE-OFFS, DUCT MOUNTED
COILS, VOLUME DAMPERS, FIRE DAMPERS, DIFFUSER BACKS, ETC. WITH FIBERGLASS INSULATION
AND VAPOR BARRIER AS SPECIFIED, UNLESS NOTED OTHERWISE. SEAL ALL VAPOR BARRIER
JOINTS.
26. INSULATE INDOOR CONDENSATE DRAIN PIPING WITH FLEXIBLE ELASTOMERIC THERMAL
INSULATION.
27. INSULATE ALL REFRIGERANT PIPING WITH FLEXIBLE ELASTOMERIC THERMAL INSULATION. LINES
LOCATED OUTDOORS SHALL BE INSULATED AND JACKETED WITH ALUMAGUARD 60 BY POLYGUARD
PRODUCTS (OR EQUAL). PROPERLY SUPPORT PIPING WITH UNISTRUT SYSTEMS.
28. INSULATE HYDRONIC PIPING PER WRITTEN SPECIFICATIONS.
29. CONTRACTOR SHALL BE RESPONSIBLE FOR THE COMPLETE AND PROPER INSTALLATION OF
THERMOSTATS AND ALL OTHER FIELD MOUNTED CONTROL COMPONENTS. THE HVAC EQUIPMENT
MANUFACTURER SHALL FURNISH COMPLETE WIRING DIAGRAMS TO THE INSTALLER FOR USE IN
WIRING CONTROLS. ALL CONTROL WIRING SHALL BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE CONTROL AND/OR ELECTRICAL SPECIFICATIONS AND THE LATEST NEC (NATIONAL
ELECTRICAL CODE) EDITION.
30. PER ADA STANDARDS, TOP OF THERMOSTATS AND SIMILAR CONTROLS SHALL BE MOUNTED AT 48"
(MAXIMUM) ABOVE THE FINISHED FLOOR.
CD
#
CONTROL DAMPER (SEE SCHEDULE)
BT
#
BUFFER TANK (SEE SCHEDULE)
KH
#
KITCHEN RANGE HOOD (SEE SCHEDULE)
31. THE FIRE ALARM CONTRACTOR SHALL FURNISH A DUCT SMOKE DETECTOR FOR EACH HVAC
SYSTEM THAT IS 2,000 CFM OR GREATER. THE DUCT SMOKE DETECTOR SHALL BE COMPATIBLE
WITH FIRE ALARM SYSTEM. THE MECHANICAL CONTRACTOR SHALL RECEIVE THE DUCT SMOKE
DETECTOR AND INSTALL IN RETURN AIR DUCTWORK SO AS TO BE ACCESSIBLE IN ACCORDANCE
WITH THE INTERNATIONAL MECHANICAL CODE. THE DUCT SMOKE DETECTOR SHALL BE
INTERLOCKED WITH THE HVAC UNIT AND FIRE ALARM SYSTEM TO SHUT DOWN THE SUPPLY AIR FAN
AND GENERATE A GENERAL ALARM CONDITION WHEN SMOKE IS SENSED IN THE DUCT.
32. BALANCE AIR AND WATER FLOWS AND SUBMIT REPORTS FOR ENGINEER'S APPROVAL. TESTING,
ADJUSTING, AND BALANCING SHALL BE PERFORMED BY A CERTIFIED AABC CONTRACTOR.
33. THE CONTRACTOR SHALL FURNISH AND INSTALL ADDITIONAL SHEAVES, PULLEYS, BELTS AND/OR
SPEED CONTROLLERS AS REQUIRED TO BRING AIR SYSTEM TO WITHIN 10% (OR AS OTHERWISE
SPECIFIED) OF DESIGN.
REMARKS AND ACCESSORIES:
1. ROOM NC LEVEL SHOWN INCLUDES ATTENUATION TRANSFER FUNCTIONS OBTAINED FROM TABLES IN ARI STANDARD 885.
2. SOUND DATA SHALL BE OBTAINED FROM TESTS CONDUCTED IN ACCORDANCE WITH ARI STANDARD 880-98.
3. UNIT SHALL BE AHRI CERTIFIED.
4. PROVIDE UNIT CONNECTION WITH STRAINER, BALL VALVES, TEMPERATURE AND PRESSURE TEST PORTS, AND PRESSURE INDEPENDENT AUTOMATIC FLOW LIMITER (BELL AND GOSSETT CIRCUIT SENTRY OR APPROVED EQUAL). REFER TO DETAIL.
USE OF FLEXIBLE HOSE KITS IS NOT ACCEPTABLE.
5. PROVIDE UNIT WITH FULLY MODULATING CONTROL VALVE ASSEMBLY TO SHUT-OFF THE FLOW OF WATER THROUGH THE UNIT WHEN THE UNIT IS OFF. UNIT SHALL OPEN QUICKLY TO PREVENT UNIT TRIP-OUT, AND CLOSE SLOWLY TO PREVENT
WATER HAMMER. WATER REGULATING VALVE SHALL FAIL OPEN. CONTROL VALVE SHALL BE PROVIDED BY THE TEMPERATURE CONTROLS CONTRACTOR.
6. MAINTAIN MANUFACTURER'S RECOMMENDED CLEARANCES.
IMPORTANT NOTICE
1. EXTERIOR WALLS FOR THIS BUILDING ARE CONSTRUCTED OF ICF (INSULATED CONCRETE FORM).
THE SUBCONTRACTORS SHALL COORDINATE NECESSARY ROUGH-IN OF SYSTEMS WITHIN WALLS.
THIS MUST BE DONE PRIOR TO THE CONCRETE POUR AND IS THE RESPONSIBILITY OF THE
SUBCONTRACTOR WHO REQUIRES THE PENETRATION OR CONCEALMENT.
7. ALL HOT WATER COIL CONNECTIONS AND BRANCH PIPING SHALL BE AT MINIMUM 3/4" UNLESS OTHERWISE NOTED.
8. BOX STATIC PRESSURE DROP INCLUDES COIL AT SCHEDULED MAXIMUM AIR FLOW RATE.
9. PROVIDE MOUNTING BRACKETS TO ACCEPT ALL-THREAD HANGING RODS OR WIRE HANGERS.
2. AT EXTERIOR ICF WALLS, ALL AREAS OF ICF FOAM INSULATION ROUTED OUT FOR ELECTRICAL
CONDUIT, PLUMBING, ETC. SHALL BE SPRAY-FOAMED AND RE-INSULATED AROUND SUCH
INSTALLATION TO RETARD THERMAL TRANSMISSION.
10. PROVIDE UNITS WITH A MINIMUM OF 22 GAUGE G90 GALVANIZED METAL DOUBLE-WALL CONSTRUCTION COVERING ALL INSULATION.
11. PROVIDE UNITS WITH A BOTTOM COIL ACCESS PLATE FOR CLEANING THE REHEAT COIL.
12. THE MECHANICAL CONTRACTOR SHALL COORDINATE ALL UNIT COMPONENTS WITH THE MANUFACTURER AND THE TEMPERATURE CONTROL CONTRACTOR TO ASSURE THAT ALL OPTIONS AND ACCESSORIES ARE FURNISHED AS SPECIFIED.
13. COORDINATE INSTALLATION OF TEMPERATURE CONTROLS CONTRACTOR-SUPPLIED CONTROLLER CAPABLE OF CONTROLLING ALL UNIT FUNCTIONS AND COMMUNICATING PEER-TO-PEER WITH THE FACILITY DDC SYSTEM UTILIZING NATIVE
BACNET PROTOCOL AS SPECIFIED.
14. PROVIDE UNIT WITH FULLY MODULATING CONTROL DAMPER.
15. PROVIDE UNIT WITH FLOW RING FOR AIR FLOW MEASURING.
16. PROVIDE CONTROLS ENCLOSURE FOR FIELD MOUNTED CONTROLS. TEMPERATURE CONTROLS CONTRACTOR SHALL PROVIDE CONTROLS, ACTUATOR, AND DISCONNECT MEANS AT EACH AIR TERMINAL BOX LOCATION.
17. ELECTRICAL CONTRACTOR SHALL PROVIDE CENTRALLY LOCATED 120V TO 24V TRANSFORMERS FOR MULTIPLE UNIT CONNECTIONS. ELECTRICAL CONTRACTOR SHALL PROVIDE DISCONNECT AT EACH TRANSFORMER LOCATION. TEMPERATURE
CONTROLS CONTRACTOR SHALL PROVIDE ALL CLASS II LOW VOLTAGE WIRING BETWEEN TRANSFORMER AND TERMINAL BOX ACTUATORS. ELECTRICAL CONTRACTOR SHALL COORDINATE LOCATIONS OF TRANSFORMERS WITH TEMPERATURE
CONTROLS CONTRACTOR.
18. REFER TO ELECTRICAL PLANS FOR POWER TO UNIT.
CARRIER, ETI, NAILOR, PRICE, TRANE, OR APPROVED EQUAL
HVAC LEAD SHEET
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
H-0.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
MECHANICAL
CONSTRUCTION NOTES
DUCT RUN-OUT
SCHEDULE
CFM RANGE
BRANCH SIZE
0 - 100
6"Ø
101 - 200
8"Ø
200 - 375
10"Ø
375 - 600
12"Ø
VAV BOX INLET
BRANCH SIZE
SCHEDULE
13
12
175
175
AFD
FR1
STORAGE
MECH./ELEC.
B
1B
124
17
S -4
125
12"x10" SA
(LINED)
2
R -2
350
S -4
S -4
8"x8"
SA
125
8"x8"
125
SA
100
10"x10" SA
3
4
R -3
450
VAV
10
10"x8"
SA
FR1
S -2
175
AFD
R -1
175
T
CHILDREN/
JUVENILE
200
RA
T
200
VAV
7
200
107
S -2
114
S -2
200
109
34"x18" RA
S -3
VAV
5
230
VAV
6
S -2
200
S -2
S -2
200
200
(DROP)
12"x12" SA
CIRCULATION
112
VAV
2
S -2
200
16"x14" SA
10"x10"
SA
9
10"Ø
10
6"Ø
11
14"Ø
CONNECT 6"Ø EA TO FULL-SIZE EA LOUVER PLENUM WITH CONTROL DAMPER,
CD-1, INTEGRATED WITH ASSOCIATED EXHAUST FAN. SEE CONTROL DAMPER
SCHEDULE.
7
CONNECT 6"Ø EA TO FULL-SIZE EA LOUVER PLENUM WITH CONTROL DAMPER,
CD-3, INTEGRATED WITH ASSOCIATED EXHAUST FAN. SEE CONTROL DAMPER
SCHEDULE.
8
CONNECT 6"Ø EA TO FULL-SIZE EA LOUVER PLENUM WITH CONTROL DAMPER,
CD-4, INTEGRATED WITH ASSOCIATED EXHAUST FAN. SEE CONTROL DAMPER
SCHEDULE.
9
CONNECT 10"x8" EA TO FULL-SIZE EA LOUVER PLENUM WITH CONTROL DAMPER,
CD-5, INTEGRATED WITH ASSOCIATED EXHAUST FAN. SEE CONTROL DAMPER
SCHEDULE.
10
ROUTE 8"Ø RA DOWN FROM BOTTOM RA DUCT CONNECTION TO FULL-SIZE RA
GRILLE PLENUM CONNECTION (SEE DETAIL) WITH VOLUME DAMPER.
11
6" THICK CONCRETE PAD (SEE HVAC NOTES). SECURE UNIT TO PAD.
12
ROUTE FLUE AND VENT DOWN TO BOILER CONNECTION PER MANUFACTURER'S
RECOMMENDATIONS. SIZE AND MATERIAL OF FLUE AND VENT SHALL BE PER
MANUFACTURER.
13
ROUTE BOILER FLUE AND VENT UP THROUGH FLOOR TO MECH/ELEC 222. SEE
DRAWING H-1.2 FOR CONTINUATION. SIZE AND MATERIAL OF FLUE AND VENT
SHALL BE PER MANUFACTURER.
14
CONNECT 10"x8' EA TO FULL-SIZE EA LOUVER PLENUM WITH CONTROL DAMPER,
CD-6, INTEGRATED WITH ASSOCIATED EXHAUST FAN. SEE CONTROL DAMPER
SCHEDULE.
15
ROUTE WATER HEATER FLUE AND VENT UP THROUGH FLOOR TO MECH/ELEC 222.
SEE DRAWING H-1.2 FOR CONTINUATION. SIZE AND MATERIAL OF FLUE AND VENT
PER MANUFACTURER.
16
ROUTE FLUE AND VENT DOWN TO WATER HEATER CONNECTION (SEE PLUMBING
DRAWINGS) PER MANUFACTURER'S RECOMMENDATIONS. SIZE AND MATERIAL OF
FLUE AND VENT PER MANUFACTURER.
17
MECHANICAL CONTRACTOR SHALL COORDINATE DUCT ROUTING WITH
ELECTRICAL CONTRACTOR FOR ELECTRICAL PANEL CLEARANCE REQUIREMENTS.
18
CONTRACTOR SHALL VERIFY WITH FABRIC DUCT MANUFACTURER DUCT SIZE,
VENT SIZES AND O'CLOCK POSITIONS APPROPRIATE FOR THIS SPACE.
S -2
200
MEN
116
12"x16"
SA
S -1
EF
6
(RISE)
40
BOOK RETURN
102
R -1
1200
R -1
380
16"x14"
RA
VAV
4
S -2
4"Ø
6
200
T
16"x12" SA
VESTIBULE
101
S -2
16"x20" RA
170
S -2
200
200
S -2
S -2
200
200
S -2
S -2
108
200
200
20"x18" RA
YOUNG ADULTS
S -2
S -2
200
200
S -2
14"x10" SA
R -1
1050
S -2
12"x12" SA
12"x10" RA
16"x12"
SA
20"x22" SA
200
200
RISE
8
TRANSITION FROM SHEET METAL TO FABRIC DUCT. PAINT TRANSITION TO MATCH
FABRIC DUCT.
117
10"x12"
SA
200
S -2
12"Ø
5
10"x8"
EA
S -2
S -2
7
ROUTE 8"Ø SA DOWN FROM BOTTOM SA DUCT CONNECTION TO SA DIFFUSER
CONNECTION WITH VOLUME DAMPER.
WOMEN
S -2
200
10"Ø
200
115
14"x14" SA
200
10"Ø
6
4
14
S -2
16"x14"
RA
(DROP)
26"x18" RA
S -2
5
8
26"x16" SA
R -1
1050
12"Ø
ROUTE 10"x8" SA DOWN FROM BOTTOM SA DUCT CONNECTION.
R -1
1200
150
200
4
3
T
S -2
S -2
16"Ø
ROUTE 60"x22" SA DOWN FROM MECH/ELEC 222 ABOVE. SEE DRAWING H-1.2 FOR
CONTINUATION.
200
40
BRANCH MNGR
16"x20" RA
38"x22" SA
200
16"x12"
SA
S -1
150
150
S -2
3
2
9
RISE CUSTODIAL
118
R -1
150
S -2
230
16"Ø
7
S -2
T
S -3
2
ROUTE 54"x24" RA UP THROUGH FLOOR TO MECH/ELEC 222 ABOVE. SEE DRAWING
H-1.2 FOR CONTINUATION.
S -2
R -1
800
T
6
119
EF
4
14"x12" RA
T
EF
5
6"Ø
EA
40
(DROP)
14"x14"
SA
8"Ø
16"x16" SA
(LINED)
6"Ø EA
VAV
8
14"x12" SA
1
5
EF
3
10
S -2
YOUTH PROGRAM
BRANCH SIZE
1
L-1
WORKROOM
28"x20" RA
S -2
S -1
(RISE)
22"x20" RA
R -4
690 14"x12"
230
VAV
9
R -1
1000
S -2
(DROP)
121
12"x12" SA
6"Ø EA
18"x12" RA
12"x12" SA
111
123
BOOK MOBILE
VAV
11
125
60"x22" SA
125
AFD
R -1
250
CORR.
14"x14"
SA
44"x22" SA
P)
R
S -2
(D
AFD
6"Ø EA
TLT
E-1
70
S -3
O
FR1
18
VAV BOX NO.
(APPLIES TO THIS DRAWING ONLY)
T
4
12"x12"
34"x22" RA
EF
1
T
8"Ø
S -5
200
12"Ø FABRIC SA = 1200 CFM
S -4
28"x24" RA
28"x24" RA ELECTRICAL
34"x24" RA
S -4
122
PLUMBING
34"x24" RA
110
BM OFFICE
B
1A
1
STAIR
16
(RISE)
FR1
15
#
200
COLLECTIONS
106
S -2
S -2
200
AFD
170
VAV
1
S -5
STAIR
200
104
T
FR1
VAV
3
(DROP)
ELEV.
103
(RISE)
235
R -1
1100
S -3
16"x14" RA
S -3
16"x14" RA
20"x22" SA
16"x14" RA
225
FR1
S -3
S -3
225
225
225
EQUIP.
105
R -1
1100
24"x12" SA
IU
1
S -3
225
16"x12" SA
10"x12" SA
S -3
T
OU
1
16"x12" SA
T
11
S -3
S -3
S -3
S -3
S -3
S -3
240
240
240
240
240
240
CLASSIFIED ASSEMBLY LEGEND
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
HVAC FIRST FLOOR PLAN
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
H-1.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
G
03/01/2018
CU
1A
26
1
2
5
4
9
ROUTE 54"x24" RA UP THROUGH FLOOR FROM CEILING SPACE BELOW AND
CONNECT TO FULL-SIZE RA PLENUM AT UNIT CONNECTION. SEE DRAWING H-1.1
FOR CONTINUATION.
VAV BOX NO.
BRANCH SIZE
5
12
12"Ø
ROUTE 28"x36" RA DOWN FROM TRUSS SPACE (OFFSET AS REQUIRED FOR ROOF
TRUSS) AND CONNECT TO FULL-SIZE RA PLENUM AT UNIT CONNECTION. SEE
DRAWING H-1.3 FOR CONTINUATION.
13
8"Ø
6
ROUTE 28"x40" REA FROM RELIEF AIR FAN AND DROP AND CONNECT TO FULL-SIZE
RA PLENUM AT UNIT CONNECTION.
14
8"Ø
15
16"Ø
16
16"Ø
7
17
6"Ø
ROUTE BOILER INTAKE AND VENT PIPING AND WATER HEATER INTAKE AND VENT
PIPING UP FROM MECHANICAL ROOM BELOW AND TERMINATE THROUGH
SIDEWALL WITH CONCENTRIC VENT PER MANUFACTURER'S REQUIREMENTS. SIZE
AND MATERIAL OF FLUE AND VENT SHALL BE PER MANUFACTURER.
AHU
1
S -2
18
14"Ø
8
NOT USED.
225
19
10"Ø
9
20
8"Ø
PROVIDE AND INSTALL SILENCER PER RELIEF AIR FAN MANUFACTURER'S
RECOMMENDATIONS (SEE VENTILATING FAN SCHEDULE).
21
12"Ø
10
ROUTE 62"x22" OA DOWN FROM INTAKE HOOD ON ROOF DOWN TO UNIT
CONNECTION. TRANSITION AND OFFSET AS REQUIRED FOR ROOF TRUSS.
22
10"Ø
23
6"Ø
11
ROUTE 28"x28" RA DOWN FROM TRUSS SPACE AND ROUTE IN CEILING SPACE. SEE
DRAWING H-1.3 FOR CONTINUATION.
223
RH
1
VAV
22
24
8"Ø
12
ROUTE 12"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO FULL-SIZE RA
GRILLE PLENUM (SEE DETAIL) WITH VOLUME DAMPER. SEE DRAWING H-1.3 FOR
CONTINUATION.
FR1
S -2
VESTIBULE
212
19
R -1
160
160
VAV
20
12"x12" SA
175
13
ROUTE 60"x22" SA FROM FULL-SIZE SA PLENUM AT UNIT CONNECTION AND DOWN
THROUGH FLOOR TO CEILING SPACE BELOW. SEE DRAWING H-1.1 FOR
CONTINUATION.
14
ROUTE 72"x20" SA FROM FULL-SIZE SA PLENUM AT UNIT CONNECTION AND UP TO
ABOVE CEILING.
15
ROUTE 40"x28" REA UP THROUGH ROOF AND TERMINATE AT RELIEF AIR HOOD
CONNECTION.
175
34"x20" SA
19
R -1
250
RESEARCH
213
30"x20" SA
17
12"x12" SA
T
S -2
VAV
19
S -3
150
(RISE)
DIRECTOR
210
S -3
275
275
28
R -1
300
40
28
12
R -1
470
16
ROUTE 10"Ø EA DOWN FROM TRUSS SPACE AND CONNECT TO FULL-SIZE EA
LOUVER PLENUM WITH CONTROL DAMPER, CD-12, IN VERTICAL. SEE DRAWING
H-1.3 FOR CONTINUATION.
17
ROUTE 10"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO FULL-SIZE RA
GRILLE PLENUM (SEE DETAIL) WITH VOLUME DAMPER. SEE DRAWING H-1.3 FOR
CONTINUATION.
18
ROUTE 6"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO FULL-SIZE RA
GRILLE PLENUM (SEE DETAIL) WITH VOLUME DAMPER. SEE DRAWING H-1.3 FOR
CONTINUATION.
19
ROUTE 8"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO FULL-SIZE RA
GRILLE PLENUM (SEE DETAIL) WITH VOLUME DAMPER. SEE DRAWING H-1.3 FOR
CONTINUATION.
40
20
ROUTE 14"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO FULL-SIZE RA
GRILLE PLENUM (SEE DETAIL) WITH VOLUME DAMPER. SEE DRAWING H-1.3 FOR
CONTINUATION.
21
ROUTE SA UP IN TRUSS SPACE AND OVER FOLDING WALL STRUCTURAL ELEMENT
AND DROP BACK DOWN IN CEILING SPACE.
22
ROUTE 16"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO FULL-SIZE RA
GRILLE PLENUM (SEE DETAIL) WITH VOLUME DAMPER. SEE DRAWING H-1.3 FOR
CONTINUATION.
23
ROUTE 4"Ø CLOTHES DRYER EXHAUST FROM UNIT CONNECTION AND TERMINATE
THROUGH WALL WITH WALL CAP PER MANUFACTURER'S RECOMMENDATION.
INSTALL BACKDRAFT DAMPER IN WALL CAP. PAINT CAP TO MATCH WALL.
24
ROUTE 10"Ø EA UP FROM FAN CONNECTION TO TRUSS SPACE. SEE DRAWING
H-1.3 FOR CONTINUATION.
25
ROUTE 20"x12" RA DOWN FROM TRUSS SPACE AND CONNECT TO FULL-SIZE RA
GRILLE PLENUM (SEE DETAIL) WITH VOLUME DAMPER. SEE DRAWING H-1.3 FOR
CONTINUATION.
26
6" THICK CONCRETE PAD. SEE HVAC NOTES.
27
ROUTE 8"x8" SA UP TO TRUSS SPACE. SEE DRAWING H-1.3 FOR CONTINUATION.
28
ROUTE 6"Ø SA DOWN FROM TRUSS SPACE AND CONNECT TO SA DIFFUSER WITH
VOLUME DAMPER. SEE DRAWING H-1.3 FOR CONTINUATION.
29
ROUTE 8"Ø SA DOWN FROM TRUSS SPACE AND CONNECT TO SA DIFFUSER WITH
VOLUME DAMPER. SEE DRAWING H-1.3 FOR CONTINUATION.
30
CONNECT 6"Ø EA TO FULL-SIZE EA LOUVER PLENUM WITH CONTROL DAMPER,
CD-9, INTEGRATED WITH ASSOCIATED EXHAUST FAN. SEE CONTROL DAMPER
SCHEDULE.
31
CONNECT 6"Ø EA TO FULL-SIZE EA LOUVER PLENUM WITH CONTROL DAMPER,
CD-8, INTEGRATED WITH ASSOCIATED EXHAUST FAN. SEE CONTROL DAMPER
SCHEDULE.
32
CONNECT 8"x6" EA TO FULL-SIZE EA LOUVER PLENUM WITH CONTROL DAMPER,
CD-11, INTEGRATED WITH ASSOCIATED EXHAUST FAN. SEE CONTROL DAMPER
SCHEDULE.
33
CONNECT 10"Ø EA TO FULL-SIZE EA LOUVER PLENUM WITH CONTROL DAMPER,
CD-10, INTEGRATED WITH ASSOCIATED EXHAUST FAN. SEE CONTROL DAMPER
SCHEDULE.
34
ROUTE 10"Ø EA DOWN FROM TRUSS SPACE AND CONNECT TO FULL-SIZE EA
LOUVER PLENUM WITH CONTROL DAMPER, CD-14, IN VERTICAL INTEGRATED WITH
ASSOCIATED EXHAUST FAN.. SEE DRAWING H-1.3 FOR CONTINUATION.
35
CONNECT 8"Ø EA TO FULL-SIZE EA LOUVER PLENUM WITH CONTROL DAMPER,
CD-13, INTEGRATED WITH ASSOCIATED EXHAUST FAN. SEE CONTROL DAMPER
SCHEDULE.
36
CONNECT S-4 (180 CFM) TO BOTTOM OF 12"x10" SA.
37
CONNECT S-4 (180 CFM) TO BOTTOM OF 10"x10" SA.
S -1
38
CONNECT S-4 (200 CFM) TO BOTTOM OF 8"x8" SA.
50
39
SUSPEND UNIT IN ROOM HIGH AS POSSIBLE.
40
SUSPEND FAN BELOW CEILING HIGH AS PRACTICAL AND TERMINATE FAN INTAKE
WITH 1/2" WIRE MESH.
16
L-2
31
WOMEN
216
235
VAV
14
S -2
12"x10"
SA
S -2
S -2
150
200
R -1
600
20
T
200
10"x10"
SA
VAV
12
E-1
340
21
10"x10"
SA
12"x14"
SA
R -1
650
S -3
S -3
S -3
250
235
235
22
10"Ø
R -1
600
EF
10
S -2
16"x14"
SA
200
14"x14"
SA
200
L-3
35
IS
33
E)
R -1
800
22
S -3
S -3
230
230
275
250
150
R -1
120
S -2
200
VAV
13
R -1
300
S -2
150
(DROP)
17
S -2
T
150
CORRIDOR
201
19
R -1
350
19
VAV
17
10"x10"
SA
24
R -1
175
T
175
300
UTILITY
202
10"x10"
SA
T
S -2
S -2
150
CATER
206
EF
14
S -2
STUDY
205
12
(RISE)
(RISE)
STUDY
208
175
T
R -5
1200
25
R -5
1200
S -3
S -3
300
300
VAV
16
S -3
300
14"x14" SA
25
R -5
1200
R -5
1200
S -3
S -3
300
250
MEETING ROOM A
203
22"x14" SA
S -3
S -3
300
300
300
VAV
15
S -2
200
S -3
300
S -3
STORAGE
203A
300
MEETING ROOM B
204
S -3
S -3
S -3
S -3
S -3
S -3
300
300
300
300
300
300
PROJECT
NORTH
FR1
12"x14" SA
S -3
FR1
26"x14" SA
10"Ø
R -1
400
T
25
18"x14" SA
25
AFD
AFD
17
28"x14" SA
R -1
300
S -3
150
175
120
17
10"x14"
SA
S -2
S -2
24
EF
13
12"x10" SA
S -2
150
MAKER
215
EF
12
26"x20" SA
275
8"x10"
SA
16"Ø SA
S -3
150
S -2
T
R -1
930
T
S -3
S -2
S -2
22
S -3
MTG. STORAGE
207
23
(DROP)
A/V-STACKS
209
12"x14" SA
R -1
800
34
10"Ø
8"x12"
SA
MEN
217
S -2
(R
22
32
6"Ø EA
S -3
COMPUTER LAB
214
16"Ø SA
30
34"x20" SA
16"x14"
SA
T
T
17
DROP
VAV
21
235
EF
11
6"Ø
EA
S -1
EF
8
44"x20" SA
S -3
150
20"x14"
S -3
80
12
(DROP)
S -2
VAV
18
FILES
224
(DROP)
20
250
FAMILY
218
EF
9
S -1
R -1
80
S -2
150
R -1
450
29
STAFF TOILET 150
219
S -1
14"x12" SA
RISE
10"x10"
SA
IU
2B
15
T
72"x20"
SA
12
S -2
VAV
23
S -2
18
S -2
VAV
24
R -4
560
66"x20" SA
BOOK KEEPER
211
27
150
T
39
14
S -2
AFD
MDF
221
S
R
D
13
225
CORR.
TECH LAB
220
36
BREAK
ROOM
40
225
30"x20" SA
10"x10" SA
T
200
R -1
150
37
EF
2
S -2
26"x20" SA
10
200
S -2
12"Ø
4
8"x6" EA
IU
2A
REF
1
(SUSPEND)
S -2
R -1
400
375 - 600
ROUTE 28"x28" RA UNDER BEAM AND DROP AND CONNECT TO FULL-SIZE RA
PLENUM AT UNIT CONNECTION.
1
MECH/
ELEC
222
38
E-1
100
12
10"Ø
3
39
200
FR1
200 - 375
VAV BOX INLET
BRANCH SIZE
SCHEDULE
6
S -2
11
8"Ø
TERMINATE 7"Ø RANGE HOOD EXHAUST AIR DUCT THROUGH WALL WITH WALL
CAP (SEE KITCHEN RANGE HOOD SCHEDULE). INSTALL BACKDRAFT DAMPER IN
WALL CAP. PAINT CAP TO MATCH WALL.
7
28"x28" RA
12"Ø
6"Ø
2
28"x40" REA
AFD
0 - 100
101 - 200
(APPLIES TO THIS DRAWING ONLY)
#
26
3
R -1
375
BRANCH SIZE
TERMINATE EXHAUST AIR DUCT THROUGH WALL WITH BRICK VENT (SEE
VENTILATING FAN SCHEDULE).
OU
2B
CU
1B
CFM RANGE
1
G
OU
2A
EF
7
MECHANICAL
CONSTRUCTION NOTES
DUCT RUN-OUT
SCHEDULE
CLASSIFIED ASSEMBLY LEGEND
FLOOR PLAN
SYMBOL
REQUIRED WORK
DESCRIPTION
SCALE: 1/8" = 1'-0"
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
HVAC SECOND FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
H-1.2
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
G
03/01/2018
MECHANICAL
CONSTRUCTION NOTES
(APPLIES TO THIS DRAWING ONLY)
#
28"x36" REA DOWN FROM TRUSS SPACE TO FULL-SIZE RA PLENUM AT UNIT
CONNECTION. OFFSET AS REQUIRED TO AVOID TRUSSES. SEE DRAWING H-1.2
FOR CONTINUATION.
2
28"x28" RA DOWN FROM TRUSS SPACE TO CEILING SPACE BELOW. SEE DRAWING
H-1.2 FOR CONTINUATION.
3
62"x22" OA DOWN FROM INTAKE HOOD ON ROOF TO UNIT CONNECTION.
TRANSITION AND OFFSET AS REQUIRED. SEE DRAWING H-1.2 FOR CONTINUATION.
4
16"x14" RA DOWN FROM TRUSS SPACE AND CONNECT TO RA GRILLE PLENUM
BELOW. SEE DRAWING H-1.2 FOR CONTINUATION.
5
12"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO RA GRILLE PLENUM
BELOW. SEE DRAWING H-1.2 FOR CONTINUATION.
6
40"x28" REA UP TO RELIEF HOOD ON ROOF TO. TRANSITION AND OFFSET AS
REQUIRED. SEE DRAWING H-1.2 FOR CONTINUATION.
7
10"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO RA GRILLE PLENUM
BELOW. SEE DRAWING H-1.2 FOR CONTINUATION.
8
10"Ø EA DOWN FROM TRUSS SPACE AND CONNECT TO FULL-SIZE EA PLENUM
BELOW. OFFSET AS REQUIRED TO ACCOMMODATE TRUSS SPACING. SEE
DRAWING H-1.2 FOR CONTINUATION.
9
8"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO RA GRILLE PLENUM BELOW.
SEE DRAWING H-1.2 FOR CONTINUATION.
10
6"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO RA GRILLE PLENUM BELOW.
SEE DRAWING H-1.2 FOR CONTINUATION.
11
COORDINATE ALL DUCT ROUTING WITHIN ROOF TRUSSES WITH ROOF TRUSS
MANUFACTURER. SEE STRUCTURAL DRAWINGS.
12
14"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO RA GRILLE PLENUM
BELOW. SEE DRAWING H-1.2 FOR CONTINUATION.
13
16"x14" SA UP FROM CEILING SPACE BELOW. TRANSITION AND ROUTE IN TRUSS
SPACE AS SHOWN TO AVOID FOLDING PARTITION STRUCTURE.
14
12"x14" SA DOWN FROM TRUSS SPACE TO CEILING SPACE BELOW.
15
16"Ø RA DOWN FROM TRUSS SPACE AND CONNECT TO RA GRILLE PLENUM
BELOW. SEE DRAWING H-1.2 FOR CONTINUATION. COORDINATE WITH FOLDING
PARTITION BELOW.
16
20"x12" RA DOWN FROM TRUSS SPACE AND CONNECT TO RA GRILLE PLENUM
BELOW. SEE DRAWING H-1.2 FOR CONTINUATION.
17
8"x8" SA UP FROM CEILING SPACE BELOW. SEE DRAWING H-1.2 FOR
CONTINUATION.
18
6"Ø SA DOWN FROM TRUSS SPACE INTO CEILING SPACE BELOW. SEE DRAWING
H-1.2 FOR CONTINUATION.
19
8"Ø SA DOWN FROM TRUSS SPACE INTO CEILING SPACE BELOW. SEE DRAWING
H-1.2 FOR CONTINUATION.
20
TYPICAL STRUCTURAL ROOF TRUSS. SEE STRUCTURAL DRAWINGS.
G
1
1
FR1
36"x28" RA
3
2
5
11
RH
1
(ROOF)
5
6
(TYP.)
8"x8" SA
17
32"x28" RA
IH
1
(ROOF)
5
19
FR1
7
9
10
18
28"x28" RA
18
8
5
9
12
12
13
32"x22" RA
7
10"Ø
EA
12"x14" SA
11
20
(TYP.)
(TYP.)
15
8
24"x22" RA
28"x24" RA
14
15
15
15
28"x18" RA
12
9
9
7
24"x18" RA
7
24"x18" RA
7
10"Ø
EA
8
5
16
16
16
16
FR1
FR1
PROJECT
NORTH
CLASSIFIED ASSEMBLY LEGEND
ATTIC PLAN
SYMBOL
SCALE: 1/8" = 1'-0"
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
HVAC ATTIC PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
H-1.3
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
HYDRONIC
EQUIPMENT BRANCH
PIPING SCHEDULE
STAIR
FR1
FR1
A
125
FR1
H1.4
ELECTRICAL
STORAGE
PLUMBING
110
MECH./ELEC.
124
UNIT TAG
BRANCH PIPE SIZE
VAV-1
3/4"
VAV-2
1-1/4"
VAV-3
1-1/4"
VAV-4
1"
VAV-5
3/4"
VAV-6
1"
VAV-7
1"
VAV-8
3/4"
VAV-9
1"
VAV-10
3/4"
VAV-11
1"
MECHANICAL
CONSTRUCTION NOTES
(APPLIES TO THIS DRAWING ONLY)
1
DROP SUPPLY AND RETURN PIPING TO UNIT CONNECTION PER DETAIL AND SIZE
PER "HYDRONIC EQUIPMENT BRANCH PIPING SCHEDULE".
2
INSTALL DIFFERENTIAL PRESSURE TRANSMITTER WITH ISOLATION VALVES PER
"VARIABLE SPEED PUMPING SCHEMATIC" ON DRAWING H4.2. ALSO INSTALL
FULL-SIZE BY-PASS WITH MODULATING VALVE AT END OF MAIN WITH AUTO. AIR
VENT (AAV) AT HIGHEST POINT OF RETURN MAIN AND ROUTE DRAIN LINE AND
CONNECT TO NEAREST CONDENSATE DRAIN PIPING.
3
ROUTE 3" S/R PIPING DOWN TO BOILER CONNECTIONS PER MANUFACTURER'S
RECOMMENDATIONS.
4
WATER HEATERS (SEE PLUMBING DRAWINGS).
5
4" THICK CONCRETE HOUSEKEEPING PAD (SEE HVAC NOTES).
6
CHEMICAL SHOT FEEDER. SEE DETAIL ON DRAWING H4.1.
7
SEE FILL LINE DETAIL ON DRAWING H-4.1.
8
EXPANSION TANK (SUSPENDED).
9
AIR/DIRT SEPARATOR.
10
INSTALL BUTTERFLY ISOLATION VALVES.
11
ROUTE 2-1/2" S/R PIPING UP WALL THROUGH FLOOR TO MECH/ELEC ROOM 222
(SEE DRAWING H-1.5 FOR CONTINUATION).
12
ROUTE REFRIGERANT PIPING AND 1-1/2" COPPER CONDENSATE DRAIN PIPING
EXPOSED ON WALL AND PENETRATE WALL LOW WITH WALL SLEEVE.
13
TERMINATE 1-1/2" COPPER CONDENSATE DRAIN PIPE IN SPLASH BLOCK.
BM OFFICE
122
BOOK MOBILE
121
UP
#
FR1
FACP
1
CORRIDOR
FR1
123
2-1/2" R/S
VAV
9
TLT
VAV
11
STAFF
TLT
1-1/4" S/R
119
111
1
VAV
7
1
2" R
CUSTODIAL
WORKROOM
107
114
YOUTH PROGRAM
118
2" S
CHILDREN/
JUVENILE
BRANCH MNGR
115
109
VAV
8
VAV
6
WOMEN
117
1" S/R
1
1
1
MEN
VAV
5
2" R
116
CIRCULATION
B
1A
2" S
112
BP
1A
B
1B
BP
1B
3" S (HIGH)
3" R (LOW)
3
4
(TYP.)
PLUMBING
BOOK RETURN
1-1/2" R/S
1
YOUNG ADULTS
P
1B
P
1A
VESTIBULE
BOILER
101
8
1
STAIR
DP
1" S
104
1" R
UP
COLLECTIONS
FR1
ELEV.
VAV
3
122
FR1
VAV
10
TCP
106
BM OFFICE
3" R
2
VFD-P-1A
9
VFD-P-1B
1-1/2" S
1
7
124
FR1
VAV
1
6
3" S
1-1/2" R
VAV
4
5
ELECTRICAL
102
1
10
S
FR1
S
CORRIDOR
1
11
123
FR1
EQUIP.
105
12
2-1/2" S
103
2-1/2" R
108
BT
1
3" S
VAV
2
IU
1
PROJECT
NORTH
OU
1
13
A
H1.4
ENLARGED FLOOR PLAN
SCALE: 1/4" = 1'-0"
CLASSIFIED ASSEMBLY LEGEND
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
HVAC PIPING FIRST FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
H-1.4
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
G
1
03/01/2018
HYDRONIC
EQUIPMENT BRANCH
PIPING SCHEDULE
G
REF
CU
1A
OU
2B
OU
2A
DN
CU
1B
2
REF
G
1
5
D
3
11
4
REF
DN
6
TCP
IU
2A
223
MDF
221
FR1
DN
TECH LAB
220
REF
REF
REF
AHU
1
VFD-AHU-1
BREAK
ROOM
MECH/
ELEC
222
IU
2B
UNIT TAG
BRANCH PIPE SIZE
VAV-12
1"
VAV-13
3/4"
VAV-14
3/4"
VAV-15
1-1/4"
VAV-16
1-1/4"
VAV-17
3/4"
VAV-18
1"
VAV-19
3/4"
VAV-20
3/4"
VAV-21
1"
VAV-22
1"
VAV-23
3/4"
VAV-24
3/4"
MECHANICAL
CONSTRUCTION NOTES
7
DN
VAV
24
FR1
VAV
20
VESTIBULE
212
1" S/R
STAFF TLT
219
FILES
224
8
VAV
21
1-1/4" S/R
8
8
1-1/2" S/R
DIRECTOR
210
ROUTE REFRIGERANT PIPING JUST ABOVE GRADE TO CONDENSING UNITS,
CU-1A & CU-1B.
3
ROUTE REFRIGERANT PIPING DOWN WALL AND THROUGH WALL LOW AS
POSSIBLE.
4
ROUTE REFRIGERANT PIPING DOWN IN CHASE AND OUT THROUGH WALL AND
CONNECT TO OUTDOOR UNITS PER MANUFACTURER'S RECOMMENDATIONS.
5
ROUTE REFRIGERANT PIPING ON CEILING AND DROP EXPOSED ON WALL TO
UNIT CONNECTION PER MANUFACTURER'S RECOMMENDATIONS. CONNECT 1"
CONDENSATE PIPE TO UNIT CONNECTION AND ROUTE TO DRAIN.
6
1" PVC CONDENSATE DRAIN PIPING DROP EXPOSED AND ATTACHED TO WALL
AND TERMINATE IN OPEN RECEPTACLE (SEE PLUMBING DRAWINGS).
7
CONNECT REFRIGERANT PIPING TO UNIT CONNECTIONS PER MANUFACTURER'S
RECOMMENDATIONS. ROUTE 1-1/2" CONDENSATE DRAIN FROM UNIT
CONNECTION TO FLOOR SINK (SEE PLUMBING DRAWINGS).
8
DROP SUPPLY AND RETURN PIPING TO UNIT CONNECTION PER DETAIL AND SIZE
PER "HYDRONIC EQUIPMENT BRANCH PIPING SCHEDULE".
9
ELECTRICAL PANELS (SEE ELECTRICAL DRAWINGS).
10
ROUTE 2-1/2" SUPPLY AND RETURN PIPING UP THROUGH FLOOR FROM
MECHANICAL ROOM BELOW. COORD. FLOOR PENETRATION AND PIPE ROUTING
WITH ELECTRICAL PANEL CLEARANCES.
11
ROUTE REFRIGERANT PIPING EXPOSED AND HIGH AS PRACTICAL. COORDINATE
WITH DUCTWORK. OFFSET AS REQUIRED.
12
INSTALL DIFFERENTIAL PRESSURE TRANSMITTER WITH ISOLATION VALVES PER
"VARIABLE SPEED PUMPING SCHEMATIC" ON DRAWING H4.2. ALSO INSTALL
FULL-SIZE BY-PASS WITH MODULATING VALVE AT END OF MAIN WITH AUTO. AIR
VENT (AAV) AT HIGHEST POINT OF RETURN MAIN AND ROUTE DRAIN LINE AND
CONNECT TO NEAREST MOP SINK.
FAMILY
218
2-1/2" R
RESEARCH
213
2
2-1/2" S
8
BOOK KEEPER
211
D
2-1/2" S
8
CONNECT REFRIGERANT PIPING TO CONDENSING UNIT CONNECTIONS PER
MANUFACTURER'S RECOMMENDATIONS.
6
2-1/2" R
VAV
22
VAV
23
5
10
CORR.
225
1
8
9
8
(APPLIES TO THIS DRAWING ONLY)
#
WOMEN
216
VAV
14
8
VAV
19
1-1/4" S/R
2" S/R
VAV
18
VAV
12
MAKER
215
2" R
COMPUTER LAB
214
MEN
217
2" S
8
A/V-STACKS
209
VAV
13
VAV
17
CORRIDOR
201
8
8
UTILITY
202
MTG. STORAGE
207
1-1/2" S/R
STUDY
208
STUDY
205
CATER
206
12
1-1/4" S
DP
1-1/4" R
DN
FR1
VAV
16
VAV
15
8
8
STORAGE
203A
FR1
MEETING ROOM A
203
MEETING ROOM B
204
PROJECT
NORTH
CLASSIFIED ASSEMBLY LEGEND
FLOOR PLAN
SYMBOL
REQUIRED WORK
DESCRIPTION
SCALE: 1/8" = 1'-0"
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
HVAC PIPING SECOND FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
H-1.5
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
ARMSTRONG MODEL 1-AV
AUTOMATIC AIR VENT
GATE VALVE
TAP TOP OF CAP
CAP
2" ON MAINS OVER 2"
SAME SIZE AS MAIN ON
MAINS 2" & SMALLER
PRESSURE OR TEMPERATURE
GAUGE
3/4"
4"
1/8" COPPER TUBING
HARD PIPING ONLY
SOFT PIPING NOT
PERMITTED
ADAPTER WITH NEEDLE
FURNISHED WITH P.T.A. WITH
1/4" FEMALE PIPE THREAD
6"
2" ON MAINS OVER 2"
SAME SIZE AS MAIN ON
MAINS 2" & SMALLER
DIRECTION OF FLOW
DIRECTION OF FLOW
UNION
HVAC
UNIT
1/8" COPPER TUBING
HARD PIPING ONLY
SOFT PIPING NOT
PERMITTED
STRAP TUBING TO MAINS 3'-0" C/C
WITH COPPER WIRE. WHEN
ADVANTAGEOUS, TUBING MAY BE
ATTACHED TO WALL.
STRAP TUBING TO MAINS 3'-0" C/C
WITH COPPER WIRE. WHEN
ADVANTAGEOUS, TUBING MAY BE
ATTACHED TO WALL.
1" PVC LINE OR MATCH CONN. SIZE
IF GREATER THAN 1"
UNION NUT ATTACHES TO
PRESSURE PLUG THREAD
SEALING GASKET
CLOSING CAP
T
HOL
S
E CA
ONEMI R
CHEDE
FE
GAS RESISTANT, SELF-CLOSING
NEOPRENE VALVE CORE
PIPE INSULATION
POSITIVE UNIT PRESSURE
1/8" BRONZE PETCOCK
E
1"
PERFORATION NEAR END OF
INSERTION NEEDLE
1/2" SCREWED FULL PIPE
COLLAR WELDED TO PIPE
SLOPE
A= 1/2 (B)
B= 1" + FAN TSP
1/8" BRONZE PETCOCK
RG
PIPE PLUG (TYP.)
TEE (TYP.)
NEGATIVE UNIT PRESSURE
03/01/2018
PU
DISMP
CH
A
C= 1" + FAN TSP
D= 1" MTN.
ROUTE TO APPROPRIATE DRAIN.
NOTE:
WHERE MAIN AIR VENTS ARE SHOWN
TO BE LOCATED OUTSIDE MECHANICAL
ROOM ABOVE CEILING, LOCATE PETCOCK
NEAR MAIN & TURN PIPING DOWN TO
DISCHARGE INTO BUCKET UNLESS
OTHERWISE NOTED TO BE TERMINATED
IN ROOM, ETC.
6" ABOVE
CEILING
6" ABOVE
CEILING
NOTE:
ROUTE CONDENSATE DRAIN AS INDICATED ON DRAWINGS
1"
TO
FL NEA
OO R
R DEST
RA
IN
DRILLED HOLE IN
PIPE WALL
"RUNNING" TRAPS ARE
NOT ACCEPTABLE.
AUTOMATIC AIR VENT DETAIL
MANUAL AIR VENT DETAIL
CONDENSATE DRAIN TRAP DETAIL
PRESSURE AND TEMPERATURE
TEST PLUG DETAIL
NO SCALE
NO SCALE
NO SCALE
NO SCALE
V
AV
T
NO
L
AL TED
H
S EC
G
IN ONNM OF
P
I
:
E H P LY CTTO
T
NOANCECT BO
BR DIRP OR
BE TO .
TO INS
MA
INEIL)
L
A
ILLDET
F
1" EE
(S
1"
RETURN AIR DUCT
(SEE PLAN FOR SIZE)
G
LY
NDINS.
A
Y A
PL N M
P
SUTUR
RE
IN
P
I
P
P
UP
FULL SIZE INTERNALLY
INSULATED PLENUM
S
OM
FR
T
EEN
V
Z
AILRSIO
7
# UL E T
G
E FLINE.
B&
P
I
PENTSID
V UT
O
E
P
E
UR
G
AU
G
P
AUTOMATIC FLOW
LIMITING VALVE.
SEE NOTE #2.
CONTROL VALVE.
SEE NOTE #1.
AN
T
N
K
IO
S
AN
RETURN AIR GRILLE
(SEE SCHEDIULE)
RETURN
OUTLET
P
EX
HOT WATER
LOOP MAIN
45°
E
L
AL
FULL PORT
BALL VALVE
SUPPLY
INLET
V
AL
V
EXTERIOR WALL
(SEE ARCHITECTURAL)
FLOW
Y-STRAINER W/
BLOWDOWN VAVLE
DUCTWORK (SEE PLAN FOR SIZE)
EXPANSION TANK PIPING DIAGRAM
LOUVER
(SEE SCHEDULE)
NOTES:
FULL SIZE PLENUM, SL0PE FOR DRAINAGE
NO SCALE
TO VAV
HOT WATER
COIL
(PREFERRED PIPING METHOD)
P & T TEST PLUG (TYP.)
B
HOT WATER BRANCH
PIPING SLOPE UP
TO MAV
HOT WATER BRANCH
PIPING SLOPE UP
TO MAIN
NO SCALE
REDUCER (TYP.)
45°
SLOPE
CEILING
(SEE ARCHITECTURAL)
RETURN-AIR GRILLE PLENUM DETAIL
VARIABLE
VOLUME BOX
E
LV
A
V AIN
N
I
O
A T DR
R
DIPEOR
PLO
F
MAV
OPTIONAL RETURN
AIR LOCATION
S
S
RE
X
BO
HOT WATER
LOOP MAIN
SLOPE
NO SCALE
12" MIN.
T
EN NG
V
ING
IR LL PIPI
P
I
A
PV
IC T A RE
AV
E
T
A
P
A
A
MAED WHETHE
LOTO A
O
S
T L
W
AUSTALIONSP INFLO
UP
O
IN CAT DR OF
LO INSTION
SL
MAREC
OP
S
LO
E
DI
PE
ING
P
I
E PAIN
PE
P
O
M
O
L
S
SL TO
E
P
OP
U
L
S
CHEMICAL FEEDER DIAGRAM
1. CONTROL VALVE SHALL BE FURNISHED BY TEMPERATURE CONTROLS CONTRACTOR.
ER
AT
(ALT. PIPING METHOD)
TO
VAV BOX BRANCH CONNECTON DETAIL
NO SCALE
W
LO BY
F
CKIDEDOR
A
B V T
O RORAC
T
P
CTER ONT
E
NNENTG C
O
C EV BIN
PRUM
PL
ILL
LOUVER-PLENUM CONNECTION, SEALED WATER TIGHT
WEEP HOLES
F
2. VALVE SHALL BE ENGINEERED FOR EACH APPLICATION AND FACTORY SET TO OPERATE WITHIN ± 5% OF
REQUIRED FLOWRATE. 2-60 PSID ALLOWABLE OPERATION RANGE AT REQUIRED FLOWRATE. INCLUDE FULL PORT
BALL VALVE AND P&T TEST PORTS. B&G CIRCUIT SENTRY OR APPROVED EQUAL.
W
E, R
V
L O
VA-12AL INGEL BQU
C
E
DUMODED SI
E
R G OV 0 P
B&
PR T 2
AP T A
SE
2-WAY HOT WATER PIPING DETAIL
TYPICAL LOUVER INSTALLATION DETAIL
NO SCALE
NO SCALE
SUSPEND EXHAUST FAN FROM
STRUCTURE WITH THREADED
ROD AND VIBRATION ISOLATORS
BACKDRAFT DAMPER
FLEX
FILL LINE DIAGRAM
PUMP MOTOR
DUCTWORK - SEE PLANS FOR SIZE
NO SCALE
RELIEF HOOD
IN-THE-LINE
CIRCULATING PUMP
L
T
STOP VALVE
(BUTTERFLY OR
BALL VALVE)
NK
U
TR
R
I
A
C
DU
L = 1/4 W 4"
MINIMUM
1" GASKETED FLANGE
BIRDSCREEN
SWING
CHECK VALVE
W
F
IR
45°
EXTERNALLY INSULATED ROUND DUCT (SEE
PLAN FOR SIZE AND LENGTH OF RUN)
ATTACH 1/4" SELF-LOCKING PLASTIC CABLE TIE
WITH TWO(2) SHEETMETAL SCREWS TO
SHEETMETAL DUCTWORK
STRAINER
ROOF CURB
LAY-IN CEILING ASSEMBLY
OW
AIR
FL
CEILING EXHAUST FAN WITH
REMOVEABLE EXHAUST GRILLE
FOR ACCESS TO AND SERVICE OF
BLOWER ASSEMBLY
DRAIN VALVE (GATE)
CONCENTRIC
REDUCER
ECCENTRIC
REDUCER
(F.O.T.)
1/4" BRONZE
PETCOCK (TYP.)
PRESSURE
GAUGE (TYP.)
LY
A
PP
U
S
LO
W
STOP VALVE
(BUTTERFLY OR
BALL VALVE)
UNION TYPE CONNECTION
EACH SIDE FOR EASY
PUMP REMOVAL
45° TAKE-OFF
ROOF
(SEE ARCHITECTURAL)
VOLUME DAMPER W/ 2" HANDLE STAND-OFF
DUCT DOWN
TAPE ALL FLEXIBLE DUCT CONNECTIONS WITH
FOIL BACK TAPE
DUCT TAKEOFF DETAIL
CEILING MOUNTED EXHAUST FAN DETAIL
NO SCALE
NO SCALE
INSULATED FLEXIBLE DUCTWORK (SEE PLAN FOR SIZE
AND AREAS WHERE FLEX DUCT IS USED)
HVAC DETAILS
IN-LINE PUMP DETAIL
DUCT TAKE-OFF/FLEX CONNECTION
INTAKE/RELIEF HOOD DETAIL
NO SCALE
NO SCALE
NO SCALE
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
H-4.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
SINGLE POINT
ELECTRICAL
CONNECTION
(SEE ELECT.)
VARIABLE SPEED PUMPING NOTES:
SINGLE POINT
ELECTRICAL
CONNECTION
(SEE ELECT.)
TEMPERATURE
CONTROL
FRONT END,
SEE NOTE #2
DUCTBELT AND BUCKLE
12"
PUMP P-1B
VARIABLE
FREQUENCY
DRIVE
ANCHOR PATCH, 4-6 PER INLET INCLUDED, SEWN TO
FABRIC SECURE WITH SELF-TAP SCREW
6-10"
EDGE-GUARD FOR METAL
EDGE (INCLUDED)
PUMP P-1A
VARIABLE
FREQUENCY
DRIVE
TWO (2)
HYDRONIC ZONE
(TOTAL)
S
P
1A
SKELACORE TYPE WITH ZIPPER AND OVERLAP
REFER TO SEQUENCE OF OPERATIONS FOR HVAC CONTROLS FOR SYSTEM REQUIREMENTS
AND INPUTS/OUTPUTS FOR EACH COMPONENT.
3.
CONTRACTOR SHALL INSTALL ELECTRICAL POWER LEADS BETWEEN EACH VARIABLE
FREQUENCY DRIVE AND EACH PUMP.
4.
MODULATING CONTROL VALVE SHALL BE FURNISHED BY THE TEMPERATURE CONTROLS
CONTRACTOR AND INSTALLED BY THE MECHANICAL CONTRACTOR.
03/01/2018
THERMAL
EXPANSION
TANK
S
AAV
FABRIC DUCT INLET ATTACHMENT DETAIL
2.
REQUIRED AT
HIGH POINTS.
SEE DETAIL.
100% FLOW
(FULL FLOW)
INLET ZIPPER
PROVIDE DIFFERENTIAL PRESSURE TRANSMITTER WITH VALVED (BALL VALVES) SENSING LINES
AS INDICATED. TRANSMITTER SHALL BE FURNISHED BY THE TEMPERATURE CONTROLS
CONTRACTOR AND INSTALLED BY THE MECHANICAL CONTRACTOR.
AAV
SEE NOTE #3
EXPOSED TRANSITION SHALL BE “PAINT
GRIP” STYLE SHEET METAL SUITABLE FOR
PAINTING. INTERNALLY INSULATE EXPOSED
TRANSITION WITH 1" ANTIMICROBIAL DUCT
LINER.
1.
TO/FROM OTHER
HYDRONIC
ZONES
BUFFER
TANK
R
R
NO SCALE
P
1B
FROM BOILERS
BACKFLOW
PREVENTER
100% FLOW
(FULL FLOW)
TO BOILERS
M
PRESSURE
REDUCING
VALVE
AUTOMATIC
FLOW LIMITER
WATER
METER
CONTROL VALVE
(SEE NOTE #4)
AIR/DIRT
SEPARATOR
MECHANICAL
ROOM
VARIABLE
VOLUME
BOX
BUILDING
LOOP
MAKE-UP WATER
DIRECT HANGING
CABLE (TYP.)
CYLINDRICAL TENSIONING
RING (CTR)
SEE NOTE #1
CYLINDRICAL TENSIONING
RING (CTR)
1" BY-PASS
INSTALLED AT
EACH END OF
SUPPLY MAIN
R
DP
1" MODULATING VALVE TO
MAINTAIN TEMPERATURE
IN MAINS
S
INTERMEDIATE
RING (IR).
TYPICAL
CYLINDRICAL TENSIONING RINGS
TYP. DIRECT RETURN ZONE
SKELECORE FABRIC TENSIONING SYSTEM SUSPENSION DETAIL
VARIABLE SPEED PUMPING SCHEMATIC
NO SCALE
NO SCALE
M
TOR
P
U O
/R FLO
S
" ND
/2O
1
2 EC
S
SE
.
MP GA.
E
T
T
.
SS
E
ER
T
PRYP.)
ME
(T
O
RM
E
THYP.) TE.)
A P
(T
GT
Y
Y
(
&
OSLVE
VA
SKELECORE FTS SUSPENSION DETAIL
COMBUSTION AIR
OR
S
N
FLUE VENT
ZIPPER ACCESS
FOR HANGER
RETURN FROM SYSTEM
SUPPLY TO SYSTEM
1/16" CABLE DROP SUPPORT WITH
GRIPPLE LOCK AT MAX. 8'-0" SPACING
BO
ILE
R
ND
E
LV
RA
A
E
V
YR
ET
F
ER
B
E
M
L
E
I
I
B
E
D
O
L
O
REALLISHETUR ERMN B
HE O
SHRN FAC
T
U
N G
F ANU
IO AU
T
M
AE G
IZ1E2"
N
S
I
R
MSBSU
INEE TO
O
L
CRE
L P
ULE PI
P
F
TEARGOOR
U
H FL
RO
C
S
DI OVE
AB
CH
T
WI S
S
T
FFEXI
O
T- OM NS
U
S
H RO TIO
S
S
CYICALOCA
N
L
GEHANOR
R
E C F
EM MELAN
AT E P
SE
NO SCALE
UN
IO
N
(TY LIM
I
PC
.)ONT
DR
TR
(TYAIN
OL
P.) VA
S
CA
LV
P(
E
TY
P.)
LO
CUW W
T-O AT
FF ER
NOTES:
1.
BOILER SHALL HAVE HIGH LIMIT AND OPERATING LIMIT CONTROLS
WITH A MAX. DIAL SETTING OF 250°F.
2.
PIPING SHALL BE TYPE "L" HARD COPPER ASTM B88 OR
SCHEDULE 40 STEEL ASTM A53 SEAMLESS GRADE B.
3.
BOILER SHALL BE CONSTRUCTED AND INSTALLED IN CONFORMANCE
WITH THE COMMONWEALTH OF KENTUCKY'S BOILER AND PRESSURE VESSEL
AND PRESSURE PIPING LAW STATUES AND ADMINISTRATIVE REGULATIONS.
4.
GAS TRAIN VENTS SHALL BE PIPED TO OUTSIDE IN ACCORDANCE
WITH NFPA 54, NATIONAL FUEL GAS CODE.
5.
INSTALL BOILER ON EXISTING CONCRETE PAD. EXTEND AND MODIFY AS REQUIRED.
SEE HVAC NOTES.
F2IR-1/2
ST" S
FL/R T
OO O
R C/ FR
LGOM
.S
PA
S/0R
"
3/A4V-1
V
CE
3"
R
3"
S
/
O
FR
E
YPION
T
0 M NS
-4A
G
X
A HR XPAANKPT.
L
T CE SI.
DEIAPME E
N
O
O
MAL DAS LL N AC21 P
L
A
ROONTIZED.7 GALLORGE
T
AMRIZSURH 21.3 GCHA
HOES WIT 11 IAL
.
ING
G
B
PRNK ME &INIT
A
DI LUMT.
TA LUME.
E
ON
LIN EE P
VOLU
C
L
S R
IL
VO
F
O
F
E
E
S
IVE
1"
T
ITA
T
ANER
U
Q ET
AIL
T
E
M
IN R
DE
P
INLATE
UM
W
P
E
LIN
)
P
IN F 4
1A
E
O
SEYP.
(T
TO
V
AA
OREL
T
RA OD
A
D 07A
EPOL M
E
S
V
R
T T O L1
R
I
IR PR DET
D
/
A
P O
L
AIRRO R AH MVEN
"
3 G 3 O IT IR
& S- W . A
BR
L
SQUACAP
E IGH
H
P
1B
)
R
ILE
O
P.)
Y
(T
HB
C
A
.E
R
3"
VE
L
VA
P.)
Y
Y
L
F
. (T
ER
A
T
G
P.)
T
.
Y
(T 3" S
BU
SS
E
R
TE
PR
E
OM
M
.)
ER
P
H
Y
T
(T
N
IO
UN
B
1A
AA
H
3"
3"
WS
H
(
R
W
.
YP
R)
ILE
O
3
WS
H
3"
B
1B
V
WS
H
"
P
(TY
B
H
C
EA
T
BT
1
BP
1A
R
(SE
AD
S)
P
E
.
T
NCNO
O
C C
4"HVA
E
3
W
"H
BP
1B
TYPICAL INDIVIDUAL BOILER PIPING DIAGRAM
MECHANICAL ROOM PIPING DIAGRAM
NO SCALE
NO SCALE
HVAC DETAILS
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
H-4.2
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
DUCTLESS SPLIT HEAT PUMP SYSTEM EQUIPMENT SCHEDULE
INDOOR UNIT MARK
MFR.
MODEL
NUMBER
IU-1
DAIKIN
FTX
RATED
RATED
COOLING HEATING
CAPACITY CAPACITY
(BTU/HR)
(BTU/HR)
CONDENSING BOILER SCHEDULE
DESCRIPTION
AREA
SERVED
WEIGHT
(LBS)
MAX.
AIRFLOW
(CFM)
SEER
WALL MOUNT
EQUIP 105
20
417
19.0
9,000
10,000
34,000
8.4
208/1Ø
1.3
15
OU-2A
DAIKIN
RZQ
165
208/1Ø
34,000
8.4
208/1Ø
1.3
15
OU-2B
DAIKIN
RZQ
165
208/1Ø
IU-2A
DAIKIN
FHQ
SUSPENDED
MDF221
100
790
17.2
30,000
IU-2B
DAIKIN
FHQ
SUSPENDED
MDF221
100
790
17.2
30,000
HSPF
ELECT.
CHAR.
MCA
9
---
---
MOCP
OUTDOOR
UNIT MARK
---
OU-1
MFR.
MODEL
NUMBER
WEIGHT
(LBS)
ELECT.
CHAR.
MCA
MOCP
DAIKIN
RX
65
208/1Ø
12.1
FUEL TYPE
THERMAL
EFF.
FLOW RATE
@ 20 DEG ΔT
(GPM)
HEAD @ 20
DEG ΔT
(FT H2O)
PRESS.
DROP @ 20
DEG ΔT
(FT H2O)
AIR INTAKE
AND VENT
SIZE
(INCHES)
EWT
(DEG F)
LWT
(DEG F)
585.0
CONCENTRIC
97.5%
59.0
--
4.4
4"
120
600.0
585.0
CONCENTRIC
97.5%
59.0
--
4.4
4"
--
--
--
--
57.0
6.7
--
--
--
--
--
--
57.0
6.7
--
--
MODEL
APPROX.
UNIT
WEIGHT
(LBS.)
INPUT
(MBH)
OUTPUT
(MBH)
FTX600
620
600.0
LOCHINVAR
FTX600
620
LOCHINVAR
PUM200077
--
LOCHINVAR
PUM200077
--
REMARKS AND
ACCESSORIES
MARK
MFG.
15
1-11,14
B-1A
LOCHINVAR
16.5
20
1-8,10-15
B-1B
16.5
20
1-8,10-15
BP-1A
BP-1B
ELECTRICAL CHAR.
REMARKS AND
ACCESSORIES
VOLTAGE /
PHASE
MCA
(AMPS)
MOCP
(AMPS)
140
120V / 1Ø
12.0
15
120
140
120V / 1Ø
12.0
15
1-15
--
--
120V / 1Ø
2.5
15
16-17
--
--
120V / 1Ø
2.5
15
16-17
1-15
03/01/2018
REMARKS AND ACCESSORIES:
1. COOLING CAPACITIES BASED ON 95F db AMBIENT AIR TEMPERATURE AND 80F db/67F wb INDOOR AIR TEMPERATURE. HEATING CAPACITIES BASED ON 47F db/43F wb AMBIENT AIR TEMPERATURE AND 70F db INDOOR AIR TEMPERATURE.
2. PROVIDE UNIT WITH MINIMUM SEVEN-YEAR COMPRESSOR WARRANTY.
REMARKS AND ACCESSORIES:
1. PROVIDE UNIT WITH AT MINIMUM ONE (1) YEAR PARTS WARRANTY, ONE (1) YEAR LIMITED LABOR WARRANTY, AND LIMITED TEN (10) YEAR HEAT EXCHANGER WARRANTY.
2. PROVIDE UNIT WITH COMBINATION OPERATING AND HIGH-LIMIT TEMPERATURE CONTROL. ASSURE COMPLIANCE WITH KENTUCKY CODE CONTROLS.
3. PROVIDE UNIT WITH ONE-YEAR PARTS WARRANTY AND ONE-YEAR LABOR WARRANTY.
4. MAINTAIN MINIMUM MANUFACTURER'S RECOMMENDED CLEARANCES.
3. UNIT SHALL BE OF ALL WELDED CONSTRUCTION.
4. PROVIDE UNIT WITH LOW WATER CUT-OFF CONTROL.
5. PROVIDE UNIT WITH CONDENSATE DRAIN PUMP.
6. PROVIDE UNIT WITH DRAIN SENSOR THAT SHUTS DOWN THE INDOOR UNIT ANY TIME A CLOGGED CONDENSATE DRAIN IS DETECTED OR THE CONDENSATE PUMP MALFUNCTIONS.
5. PROVIDE UNIT WITH MODULATING FIRING WITH A MINIMUM 7:1 TURNDOWN.
6. PROVIDE UNIT WITH ASME RELIEF VALVE.
7. PROVIDE UNIT WITH WASHABLE, LONG-LIFE AIR FILTER.
8. PROVIDE UNIT WITH WIRED, WALL MOUNTED PROGRAMMABLE THERMOSTAT. PROVIDE ONE THERMOSTAT PER ZONE.
7. PROVIDE UNIT WITH TEMPERATURE AND PRESSURE INDICATORS AS SPECIFIED.
8. INSTALL INTAKE AND EXHAUSTING PIPE MATERIALS PER MANUFACTURER'S RECOMMENDATIONS.
9. INDOOR FAN COIL UNIT IS ELECTRICALLY POWERED BY OUTDOOR CONDENSING UNIT.
10. PROVIDE UNIT WITH LOW AMBIENT KIT CAPABLE OF OPERATION TO 0 DEG F.
11. PROVIDE UNIT WITH A FULL REFRIGERANT CHARGE.
9. PROVIDE UNIT WITH ASME CERTIFIED STAINLESS-STEEL HEAT EXCHANGER.
10. PROVIDE UNIT WITH MANUFACTURER'S START-UP AND CERTIFIED REPORT. INSTALLING CONTRACTOR START-UP IS NOT ACCEPTABLE.
12. PROVIDE UNIT THAT IS SUITABLE FOR EXTENDED LINE LENGTH.
13. MECHANICAL CONTRACTOR SHALL FURNISH AND INSTALL ALL NECESSARY MOUNTING HARDWARE NEEDED TO SUSPEND UNIT. HARDWARE SHALL INCLUDE VIBRATION ISOLATION.
14. ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL NONFUSED DISCONNECT SWITCHES ON INDOOR AND OUTDOOR UNITS.
11. BOILERS SHALL RECEIVE CONTROLS SIGNAL (0-10 VDC) FROM BUILDING MANAGEMENT SYSTEM FOR ENABLE/DISABLE, AND TEMPERATURE RESET. REFER TO SEQUENCE OF OPERATIONS FOR HVAC CONTROLS.
12. PROVIDE UNIT WITH MANUFACTURER'S HORIZONTAL CONCENTRIC VENT KIT.
13. PROVIDE WITH MANUFACTURER'S CONDENSATE NEUTRALIZATION KIT.
14. PROVIDE WITH MANUFACTURER'S VARIABLE-SPEED BOILER CIRCULATOR PUMP.
15. PROVIDE EACH UNIT WITH BACNET CARD FOR FULL INTEGRATION INTO THE BUILDING MANAGEMENT SYSTEM.
DAIKIN, CARRIER, TRANE, OR APPROVED EQUAL.
15. PROVIDE WITH BACNET CARD FOR INTEGRATION INTO BUILDING MANAGEMENT SYSTEM. ONE BACNET CARD SHALL BE SUPPLIED TO EACH BOILER FOR FULL INTEGRATION AND INDEPENDENT OPERATION.
16. PROVIDE UNIT WITH DIGITAL DISPLAY, PUMP STATUS INDICATOR, AND ALARM CONTACTS.
17. PROVIDE UNIT WITH 316 L STAINLESS STEEL SHAFT, COMPOSITE IMPELLER, COMPOSITE ROTOR CAN, AND CAST IRON HOUSING.
AERCO, RBI, LOCHINVAR, RAYPAK, OR APPROVED EQUAL
LOUVER SCHEDULE
MARK
MFR.
DESCRIPTION
SIZE
(INCHES)
MODEL
CFM
FREE AREA
(SQ. FT.)
HYDRONIC PUMP SYSTEM SCHEDULE
FACE
VELOCITY
(FPM)
PRESSURE
DROP
(IN. H2O)
TYPE OF
FRAME AND
MOUNTING
REMARKS AND
ACCESSORIES
SERVICE
MARK
MFG.
SERIES
MODEL
APPROX.
UNIT
WEIGHT
(LBS)
CONFIGURATION
KITCHEN RANGE HOOD SCHEDULE
MOTOR
SIZE
(HP)
DUTY
POINT
POWER
(BHP)
PUMP
SPEED
(RPM)
RATED
FLOW
(GPM)
TDH
(FT. H20)
PUMP
EFF.
(%)
SERVICE
PHYSICAL DATA
REMARKS AND
ACCESSORIES
MARK
MFG.
MODEL /
TYPE
SIZE
KH-1
BROAN
QS1
30
L-1
GREENHECK
DRAINABLE BLADE LOUVER
ESD-635
20 X 20 X 6
760
1.11
720
0.080
CHANNEL
EF-1,3,4,5,6
SEE BELOW
L-2
GREENHECK
DRAINABLE BLADE LOUVER
ESD-635
20 X 20 X 6
800
1.11
720
0.080
CHANNEL
EF-8,9,11,12
SEE BELOW
P-1A
BELL AND GOSSETT
E-90
2AB
110
INLINE
1.5
1.01
1725
90
30
71
BUILDING LOOP
208V / 3Ø
SEE BELOW
SEE BELOW
P-1B
BELL AND GOSSETT
E-90
2AB
110
INLINE
1.5
1.01
1725
90
30
71
BUILDING LOOP
208V / 3Ø
SEE BELOW
L-3
GREENHECK
DRAINABLE BLADE LOUVER
ESD-635
20 X 20 X 6
755
720
1.11
0.080
EF-10,13,14
CHANNEL
PERFORMANCE DATA
VOLTAGE /
PHASE
MOUNTING
MAX
AIRFLOW
(CFM)
FAN TYPE
SONES @
100 CFM
SONES @
220 CFM
FLA
(AMPS)
VOLTAGE /
PHASE
UNDER CABINET
220
AXIAL FAN
1.5
5
1.8
120V / 1Ø
REMARKS AND
ACCESSORIES
SEE BELOW
REMARKS AND ACCESSORIES:
REMARKS AND ACCESSORIES:
REMARKS AND ACCESSORIES:
1. PROVIDE UNIT WITH OPTIONAL POWER CORD KIT.
REFER TO ARCHITECTURAL PLANS FOR FINISHED MOUNTING HEIGHT AND LOCATION.
1.
PROVIDE UNIT WITH PREMIUM EFFIECENT MOTOR SUITABLE FOR VARIABLE SPEED OPERATION.
SIZES ARE SPECIFIED AS: FIRST FIGURE-WIDTH, SECOND FIGURE-HEIGHT, AND THIRD FIGURE- DEPTH.
2.
PROVIDE UNIT WITH SHAFT GROUNDING DEVICE.
3.
PROVIDE UNIT WITH EXTENDED SILL.
3.
UNITS SHALL BE SUPPORTED FROM STRUCTURE UTILIZING SPRING VIBRATION ISOLATION SYSTEM. REFER TO SPECIFICATIONS FOR SPECIFIC REQUIREMENTS.
4.
PROVIDE UNIT IN ALUMINUM CONSTRUCTION.
4.
PUMP HYDRAULIC EFFICIENCY IS BASED ON GPM FLOW RATE AND "TDH" FRICTIONAL LOSSES.
5.
PROVIDE UNIT WITH ALUMINUM BIRD SCREEN.
5.
PROVIDE UNIT WITH AT MINIMUM ONE (1) YEAR PARTS WARRANTY AND ONE (1) YEAR LIMITED LABOR WARRANTY.
6.
PROVIDE UNIT WITH 70% KYNAR FINISH. COLOR TO BE SELECTED BY ARCHITECT.
PROVIDE CLOSE-COUPLED, BRONZE-FITTED PUMP RATED FOR 175 PSI MAXIMUM WORKING PRESSURE WITH BUNA-CARBON/CERAMIC SEAL.
7.
INSTALL UNIT IN 18 GAUGE SHEETMETAL WALL SLEEVE.
6.
7.
8.
REFER TO STRUCTURAL DRAWINGS FOR LINTEL TYPE DETAILS AND NOTES.
1.
2.
2. FINISH SHALL BE BAKED ON POLYESTER PAINT OR STAINLESS STEEL AS DETERMINED BY THE ARCHITECT.
3. RANGE HOOD SHALL HAVE A FULLY ENCLOSED BOTTOM AND DISHWASHER SAFE, FULL FILTERS.
4. RANGE HOOD SHALL BE CONVERTIBLE BETWEEN 3 1/4" X 10" AND 7" ROUND DUCTED. DUCT CONNECTORS SHALL BE ADJUSTABLE TO ACCOMMODATE
OFF-CENTER DUCTWORK.
5. RANGE HOOD SHALL COME EQUIPPED WITH MANUFACTURER'S LIGHTING KIT.
6. RANGE HOOD SHALL BE CONTROLLED BY A UNIT MOUNTED ROCKER SWITCH. THE SWITCH SHALL CONTROL ALL FAN SPEEDS AND LIGHTING OPERATIONS OF THE
RANGE HOOD.
7. UNIT SHALL BE UL LISTED.
8. PROVIDE UNIT WITH ALUMINIMUM WALL CAP TERMINATION (GREENHECK MODEL WC OR EQUAL) WITH 3-COAT, FACTORY APPLIED KYNAR FINISH IN CUSTOM
COLOR TO BE SELECTED BY THE ARCHITECT. FURNISH WALL CAP WITH INTEGRAL BACKDRAFT DAMPER AND BIRD SCREEN.
9. FURNISH RANGE HOOD WITH MANUFACTURER'S INTEGRAL BACK DRAFT DAMPER.
BROAN, GE, WHIRLPOOL, OR APPROVED EQUAL
PROVIDE PUMP WITH VARIABLE FREQUENCY DRIVE FOR VARIABLE SPEED PUMPING OPERATION. VFD SHALL BE FURNISHED BY TEMPERATURE CONTROLS CONTRACTOR. REFER TO SEQUENCE OF
OPERATIONS FOR VARIABLE SPEED PUMPING REQUIREMENTS.
ARMSTRONG, BELL AND GOSSETT, TACO, OR APPROVED EQUAL
GREENHECK, NCA, RUSKIN, OR APPROVED EQUAL
VARIABLE AIR VOLUME AIR-HANDLING UNIT SCHEDULE
MARK
MFR
MODEL
SIZE
ARRANGEMENT
UNIT
WEIGHT
(LBS)
AHU-1
DAIKIN
CAH
061
HORIZONTAL
6,375
SUPPLY FAN
MAX
O.A.
(CFM)
MAX SA
(CFM)
MIN SA
(CFM)
ESP
(IN W.C.)
TSP
(IN W.C.)
QTY OF
FANS
4,545
27,400
8,220
2.5
3.66
5
DRIVE
FAN
SPEED
(RPM)
MOTOR
POWER
(BHP)
MOTOR
POWER
(HP)
EAT
(DB/WB)
(°F)
LAT
(DB/WB)
(°F)
TOTAL
CAP.
(MBH)
DIRECT
2600
4.75
6.7
78.3 / 65
55.6 / 53.5
941
GRAVITY HOOD SCHEDULE
DX COOLING COIL
SENS
AIR PD
CAP.
(IN WC)
(MBH)
680
.92
ELECTRICAL DATA
ROWS
COILS
FPI
ELEC. CHAR.
MCA
(AMPS)
6
2
6
208V/3Ø
87.2
MOCP
(AMPS)
100
REMARKS AND
ACCESSORIES
MARK
MFR.
DESCRIPTION
MODEL /
TYPE
THROAT
WIDTH
(INCHES)
THROAT
LENGTH
(INCHES)
AIRFLOW
(CFM)
THROAT
AREA
(SQ. FT.)
THROAT
VELOCITY
(FPM)
PRESSURE
DROP
(IN. H2O)
TYPE OF
FRAME AND
MOUNTING
WEIGHT
(LBS)
SERVICE
REMARKS AND
ACCESSORIES
SEE BELOW
IH-1
GREENHECK
INTAKE HOOD
WIH
44
62
13,700
18.94
723
0.094
ROOF
230
OA INTAKE
SEE BELOW
RH-2
GREENHECK
RELIEF HOOD
WRH
44
62
9,650
18.94
509
0.040
ROOF
230
RA EXHAUST
SEE BELOW
REMARKS AND ACCESSORIES:
REMARKS AND ACCESSORIES:
1.
PROVIDE UNIT WITH ONE (1) YEAR PARTS WARRANTY AND ONE (1) YEAR LABOR WARRANTY
2.
MAINTAIN MINIMUM MANUFACTURERS RECOMMENDED CLEARANCES AND ACCESS TO FILTERS AND COILS.
3.
MOUNT UNIT ON 4" CONCRETE HOUSEKEEPING PAD.
2. PROVIDE UNIT WITH GALVANIZED BIRD SCREEN.
4.
PROVIDE WITH 2" THICK MERV 8 AIR FILTERS.
3. ALL EXPOSED FASTENERS SHALL BE STAINLESS STEEL.
5.
PROVIDE UNIT WITH COMBINATION MIXING BOX, DX COOLING COIL AND SUPPLY FAN WALL ARRAY.
4. PROVIDE UNIT IN GALVANIZED CONSTRUCTION.
5. PROVIDE UNIT WITH CURB CAP, AND RUBBER STRIPPING FOR SEALING UNIT TO ROOF CURB.
1. PROVIDE UNIT WITH AT MINIMUM 1/2" THICK INSULATED HOUSING.
6.
PROVIDE UNIT WITH HOT GAS BYPASS.
7.
FAN SECTION SHALL BE DYNAMICALLY BALANCED AND SPRING ISOLATED.
8.
PROVIDE UNIT WITH GALVANIZED STEEL, INSULATED DOUBLE WALL CONSTRUCTION WITH GASKETED FRAME CHANNELS.
9.
PROVIDE UNIT WITH 6" BASE RAIL (OR HIGHER TO SUIT NECESSARY PIPING ARRANGEMENT).
6. PROVIDE UNIT WITH AT MINIMUM 12" TALL ABOVE THE FINISHED ROOFING DECK (SEE ARCHITECTURAL PLANS FOR FINISHED ROOFING ELEVATIONS), INSULATED, ROOF CURB SUITABLE FOR ROOF
TYPE AND SLOPE. INSULATION SHALL BE A MINIMUM 1-1/2" THICK.
7. PROVIDE UNIT AND CURB IN 70% KYNAR TYPE FINISH. COLOR SHALL BE SELECTED BY ARCHITECT FROM ALL AVAILABLE COLORS.
GREENHECK, NCA, RUSKIN, UNITED ENERTECH, OR APPROVED EQUAL
10. PROVIDE UNIT WITH 24V ACTUATED DAMPERS ON RETURN AND OUTSIDE AIR INLETS AT THE MIXING BOX.
11. PROVIDE UNIT WITH ELECTRICAL PHASE LOSS PROTECTION.
12. PROVIDE UNIT WITH THERMAL OVERLOAD PROTECTION.
13. PROVIDE UNIT WITH VARIABLE FREQUENCY DRIVES FOR SUPPLY AIR FANS (ONE VFD PER ROW OF FANS) FOR VAV OPERATION. SUPPLY FANS SHALL MAINTAIN REQUIRED DUCT PRESSURE FROM REMOTE SENSOR LOCATION. REFER TO SEQUENCE OF OPERATIONS. VFD'S SHALL BE PROVIDED BY THE
TEMPERATURE CONTROLS CONTRACTOR.
14. FIRE ALARM CONTRACTOR SHALL FURNISH A DUCT SMOKE DETECTOR FOR THE RETURN AIR DUCT. DUCT SMOKE DETECTOR SHALL BE COMPATIBLE WITH FIRE ALARM SYSTEM. MECHANICAL CONTRACTOR SHALL RECEIVE DUCT SMOKE DETECTOR FROM FIRE ALARM CONTRACTOR AND INSTALL IN DUCTWORK IN AN
ACCESSIBLE LOCATION AND ACCORDANCE WITH THE INTERNATIONAL MECHANICAL CODE. DUCT SMOKE DETECTOR SHALL BE INTERLOCKED WITH HVAC UNIT AND FIRE ALARM SYSTEM TO SHUT DOWN THE UNIT OPERATION AND GENERATE A GENERAL ALARM CONDITION WHEN SMOKE IS SENSED IN THE DUCT.
15. PROVIDE UNIT WITH MANUFACTURER'S START-UP AND CERTIFIED REPORT FOR ENGINEER'S APPROVAL. INSTALLING CONTRACTOR START-UP IS NOT ACCEPTABLE.
16. UNIT SHALL BE MODULAR IN DESIGN FOR FUTURE REMOVAL OF SECTIONS. UNIT SHALL SHIP IN MULTIPLE SECTIONS SUITABLE FOR INSTALL AND FUTURE REMOVAL. PROVIDE QUICK CONNECTORS AT ALL SPLICES.
BUFFER TANK SCHEDULE
17. PROVIDE UNIT WITH DOUBLE SLOPED STAINLESS STEEL DRAIN PAN TO SINGLE POINT CONNECTION.
18. PROVIDE UNIT WITH HINGED ACCESS DOORS ON BOTH SIDES OF ALL MODULES WITH FULL GRIP HANDLES.
MARK
MFG.
MODEL
TANK
VOLUME
(GALLONS)
BT-1
LOCHINVAR
BVU200
200
APPROX
DRY
WEIGHT
(LBS)
MAX
CONNECTION
DIAMETER
(INCHES)
TANK DIMENSIONS
(HEIGHT X DIAMETER)
(INCHES)
SERVICE
REMARKS AND
ACCESSORIES
990
3
90 X 32
HEATING WATER
SEE BELOW
REMARKS AND ACCESSORIES:
19. PROVIDE EXTENDED FAN BEARING LUBE LINES.
20. PROVIDE EXTENDED COIL AND DRAIN CONNECTIONS.
1. PROVIDE UNIT WITH ASME SECTION VIII, U-STAMP - 125PSI WORKING PRESSURE AT 400°F.
2. PROVIDE UNIT WITH MINIMUM 2" THICK INSULATION WITH JACKET. REFER TO SPECIFICATIONS FOR REQUIREMENTS.
21. PROVIDE FLUSH MOUNTED FILTER GAUGES.
22. PROVIDE UNIT WITH SINGLE POINT POWER CONNECTION.
3. PROVIDE UNIT MOUNTED ON A METAL TYPE BASE WITH ANCHORING CLIPS.
4. PROVIDE UNIT WITH AUTOMATIC AIR VENT.
23. CONTROLS RESPONSIBILITIES: THE EQUIPMENT PROVIDER SHALL PROVIDE ALL CONTROL FUNCTIONALITY REQUIRED FOR THE PROPER OPERATION/PROTECTION OF HIS EQUIPMENT (FANS, COMPRESSORS, COMPONENTS, ETC.). THE HVAC CONTROLS CONTRACTOR SHALL PROVIDE BUILDING CONTROL
FUNCTIONALITY PER THE SEQUENCE OF OPERATIONS SPECIFICATION VIA ON BOARD CONTROLS, INDEPENDENT DDC CONTROLS, OR COMBINATION OF BOTH. THE HVAC CONTRACTOR IS RESPONSIBLE FOR COORDINATION BETWEEN CONTROL CONTRACTOR AND EQUIPMENT PROVIDER TO ASSURE ALL
REQUIREMENTS OF THE SEQUENCE OF OPERATIONS ARE MET.
CARRIER, DAIKIN, TRANE OR APPROVED EQUAL
5. PROVIDE UNIT WITH FLANGED SYSTEM AND BOILER SUPPLY/RETURN CONNECTIONS.
6. PROVIDE UNIT WITH A FIVE (5) YEAR WARRANTY.
7. CONTRACTOR SHALL VERIFY ALL CONNECTION SIZES AND POSITIONS TO ENSURE PROPER FIT OF THE TANK.
8. PROVIDE UNIT WITH HOISTING AND LIFTING CONNECTION POINTS.
9. INSTALL TANK ON 4" THICK CONCRETE MAINTENANCE PAD.
AMTROL, LOCHINVAR, TACO, OR APPROVED EQUAL
DIFFUSER AND GRILLE SCHEDULE
PHYSICAL DATA
MARK
S-1
S-2
MFG.
PRICE
PRICE
MODEL
SPD
SPD
SIZE
24" X 24"
24" X 24"
NECK SIZE
6" Ø
8" Ø
AIR COOLED CONDENSING UNIT SCHEDULE
PERFORMANCE DATA
CORE TYPE
PLAQUE
PLAQUE
TYPE OF
MOUNTING
FT.
98
LAY-IN
4
209
LAY-IN
NECK/CORE
VELOCITY
(FPM)
SOUND
RATING
(NC)
VOLUME
DAMPER
MARK
DIR.
PRESS.
DROP
(IN. H2O)
4 WAY
0.016
500
<15
NO
CU-1A
DAIKIN
RCS
045
2875
R410A
2
NO
CU-1B
DAIKIN
RCS
045
2875
R410A
2
THROW
NOM.
CFM
7
4 WAY
0.042
600
<15
S-3
PRICE
SPD
24" X 24"
10" Ø
PLAQUE
327
LAY-IN
9
4 WAY
0.065
600
<15
NO
S-4
PRICE
520
-----
12" X 4"
LOUVER
210
DUCT
21
ADJ.
0.030
800
21
YES
S-5
PRICE
520
-----
16" X 8"
LOUVER
245
SIDEWALL
22
ADJ.
0.006
300
<15
NO
R-1
PRICE
80
24" X 24"
22" X 22"
CUBE
1,805
LAY-IN
-----
-----
0.034
500
<15
NO
R-2
PRICE
530
-----
12" X 12"
LOUVER
350
DUCT
-----
-----
0.040
400
<15
YES
R-3
PRICE
530
-----
14" X 14"
LOUVER
560
DUCT
-----
-----
0.053
460
17
YES
R-4
PRICE
80
-----
16" X 16"
CUBE
800
SURFACE
-----
-----
0.034
500
<15
NO
R-5
E-1
PRICE
PRICE
80
80
24" X 24"
24" X 24"
22" X 22"
22" X 22"
CUBE
CUBE
1,805
1,805
SURFACE
LAY-IN
-----
-----
-----
-----
0.034
0.034
500
500
REMARKS AND ACCESSORIES:
1.
FURNISH DIFFUSERS WITH SQUARE-TO-ROUND NECK TRANSITIONS AS REQUIRED.
2.
FURNISH ALL DIFFUSERS AND GRILLES WITH POWDER-COATED FINISH IN COLOR AS SELECTED BY ARCHITECT FROM ALL AVAILABLE OPTIONS.
3.
FURNISH GRILLES WITH FULL SIZED CORE. GRILLES WITH BLANK PANELS ON CORE ARE NOT ACCEPTABLE.
KRUEGER, PRICE, METAL-AIRE, TITUS OR APPROVED EQUAL
WEIGHT
(LBS)
<15
<15
NO
NO
MFR.
MODEL
SIZE
REFRIG.
CIRCUITS
COOLING
STAGES
COOLING
PERFORMANCE
CONTROL DAMPER SCHEDULE
OVERALL
WEIGHTED
SOUND
POWER
(dBA)
ELECT.
CHAR.
MCA
(AMPS)
MOCP
(AMPS)
REMARKS AND
ACCESSORIES
MBH
EER
MODULATING
469
11.4
70.0
208V / 3Ø
195.7
225
SEE BELOW
MODULATING
469
11.4
70.0
208V / 3Ø
195.7
225
SEE BELOW
MARK
MFR.
SERVICE
DESCRIPTION
MODEL /
TYPE
CFM
CONTROL
VOLTAGE
TYPE
CD-1
GREENHECK
EF-1
CONTROL DAMPER
VCDR-23
70
120V
TWO POSITION
TYPE OF
FRAME AND
MOUNTING
DUCTWORK
CD-3
GREENHECK
EF-3
CONTROL DAMPER
VCDR-23
70
120V
TWO POSITION
DUCTWORK
1-7
CD-4
GREENHECK
EF-4
CONTROL DAMPER
VCDR-23
60
120V
TWO POSITION
DUCTWORK
1-7
CD-5
GREENHECK
EF-5
CONTROL DAMPER
VCDR-23
280
120V
TWO POSITION
DUCTWORK
1-7
CD-6
GREENHECK
EF-6
CONTROL DAMPER
VCDR-23
280
120V
TWO POSITION
DUCTWORK
1-7
CD-2
REMARKS AND ACCESSORIES:
1. PROVIDE UNIT WITH ONE (1) YEAR PARTS WARRANTY, ONE (1) YEAR LABOR WARRANTY, AND FIVE (5) YEAR COMPRESSOR WARRANTY.
4. PROVIDE UNIT WITH ALL SOUND ATTENTUATION OPTIONS. OPTIONS SHALL INCLUDE SOUND BLANKETS ON SCROLL COMPRESSORS.
5. COOLING CAPACITIES ARE BASED ON 80F db/67F wb EAT, 95F db/75F wb AMBIENT CONDITIONS AND 44F SUCTION TEMPERATURE.
6. FURNISH AND INSTALL REFRIGERANT PIPING, TXV (S), SIGHT GLASS(S), TIME DELAY RELAY(S), CRANKCASE HEATER(S), REFRIGERANT VALVE(S), AND FILTER DRYER(S) AS SIZED AND
ROUTED PER THE MANUFACTURER'S RECOMMENDATIONS.
7. MAINTAIN MINIMUM MANUFACTURERS RECOMMENDED CLEARANCES.
8. PROVIDE UNIT WITH ELECTRICAL PHASE LOSS PROTECTION.
NOT USED
CD-8
GREENHECK
EF-8
CONTROL DAMPER
VCDR-23
70
120V
TWO POSITION
DUCTWORK
1-7
CD-9
GREENHECK
EF-9
CONTROL DAMPER
VCDR-23
70
120V
TWO POSITION
DUCTWORK
1-7
CD-10
GREENHECK
EF-10
CONTROL DAMPER
VCDR-23
340
120V
TWO POSITION
DUCTWORK
1-7
CD-11
GREENHECK
EF-11
CONTROL DAMPER
VCDR-23
280
120V
TWO POSITION
DUCTWORK
1-7
CD-12
GREENHECK
EF-12
CONTROL DAMPER
VCDR-23
280
120V
TWO POSITION
DUCTWORK
1-7
CD-13
GREENHECK
EF-13
CONTROL DAMPER
VCDR-23
140
120V
TWO POSITION
DUCTWORK
1-7
CD-14
GREENHECK
EF-14
CONTROL DAMPER
VCDR-23
275
120V
TWO POSITION
DUCTWORK
1-7
VCD-23
9,650
DUCTWORK
1-4,6-8
CD-15
9. PROVIDE UNIT WITH THERMAL OVERLOAD PROTECTION.
10. PROVIDE UNIT WITH GROUND FAULT PROTECTION.
1-7
NOT USED
CD-7
2. PROVIDE UNIT WITH LOW PRESSURE AND HIGH PRESSURE SWITCHES PER MANUFACTURER'S RECOMMENDATIONS.
3. PROVIDE UNIT WITH DIGITAL SCROLL COMPRESSORS.
REMARKS AND
ACCESSORIES
GREENHECK
REF-15
CONTROL DAMPER
24V
TWO POSITION
REMARKS AND ACCESSORIES:
11. PROVIDE UNIT WITH HAIL GUARD AND HINGED, LOCKABLE ACCESS DOORS.
12. PROVIDE UNIT WITH MANUFACTURER'S START-UP AND CERTIFIED REPORT FOR ENGINEER'S APPROVAL. INSTALLING CONTRACTOR START-UP IS NOT ACCEPTABLE.
13. ELECTRICAL CONTRACTOR SHALL PROVIDE NON-FUSED DISCONNECT.
1.
SIZES SHALL BE DETERMINED FROM DUCT WORK SIZES. REFER TO PLAN FOR SIZING.
2.
PROVIDE UNIT IN GALVANIZED CONSTRUCTION.
14. MECHANICAL CONTRACTOR SHALL VERIFY THAT UNIT WILL FIT IN DESIGNED SPACE BEFORE EQUIPMENT ORDER.
15. CONTROLS RESPONSIBILITIES: THE EQUIPMENT PROVIDER SHALL PROVIDE ALL CONTROL FUNCTIONALITY REQUIRED FOR THE PROPER OPERATION/PROTECTION OF HIS
EQUIPMENT (FANS, COMPRESSORS, COMPONENTS, ETC.). THE HVAC CONTROLS CONTRACTOR SHALL PROVIDE BUILDING CONTROL FUNCTIONALITY PER THE SEQUENCE OF
OPERATIONS SPECIFICATION VIA ON BOARD CONTROLS, INDEPENDENT DDC CONTROLS, OR COMBINATION OF BOTH. THE HVAC CONTRACTOR IS RESPONSIBLE FOR COORDINATION
BETWEEN CONTROL CONTRACTOR AND EQUIPMENT PROVIDER TO ASSURE ALL REQUIREMENTS OF THE SEQUENCE OF OPERATIONS ARE MET.
CARRIER, DAIKIN, TRANE OR APPROVED EQUAL
3.
PROVIDE UNIT EPDM BLADE SEALS.
4.
5.
CONTRACTOR SHALL CONFIRM DUCTWORK SIZE.
MECHANICAL CONTRACTOR SHALL PROVIDE AND INSTALL CONTROL DAMPER AND ACTUATOR. ELECTRICAL CONTRACTOR SHALL PROVIDE
WIRING BETWEEN DAMPER AND EXHAUST FAN.
OPERATION IS NORMALLY CLOSED, UNIT SHALL FAIL CLOSED.
6.
7.
8.
DAMPER AND BLADE SHALL BE 16 GAUGE CONSTRUCTION.
MECHANICAL CONTRACTOR SHALL FURNISH AND INSTALL DAMPER. TEMPERATURE CONTROLS CONTRACTOR SHALL FURNISH AND INSTALL
ACTUATOR AND ALL CONTROL WIRING BETWEEN FAN AND DAMPER.
GREENHECK, NCA, RUSKIN, OR APPROVED EQUAL
HVAC SCHEDULES
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
H-5.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
FIRE ALARM NARRATIVE
1.0 GENERAL:
THE EXISTING FIRE ALARM SYSTEM (HONEYWELL, NOTIFER NFS-320) OF THE SCHOOL WILL BE EXTENDED AND
MODIFIED AS REQUIRED SO AS TO PROVIDE VOICE EVAC FIRE ALARM WITHIN THE NEW AND EXISTING BUILDING
AREAS TO FUNCTION AS THE "HIGH" SCHOOL. THE FIRE ALARM INTEGRATOR SHALL BE VANGUARD ALARM
SERVICES, 816 MAXWELL AVE. EVANSVILLE, IN 47711, (812) 425-2616 TO INSURE SEAMLESS INTEGRATION BETWEEN
SYSTEMS.AS PART OF THIS WORK THE CONTRACTOR SHALL FURNISH ALL LABOR, SERVICES AND MATERIALS
NECESSARY AND FURNISH AND INSTALL A COMPLETE, FUNCTIONAL VOICE EVAC FIRE ALARM SYSTEM (SYSTEM).
THE SYSTEM SHALL COMPLY IN RESPECTS WITH ALL PERTINENT CODES, RULES, REGULATIONS AND LAWS OF THE
AUTHORITY HAVING JURISDICTION. THE SYSTEM SHALL COMPLY IN ALL RESPECTS WITH THE REQUIREMENTS OF
THE SPECIFICATIONS, MANUFACTURER'S RECOMMENDATIONS AND UNDERWRITERS LABORATORIES INC. (ULI)
LISTINGS. FIELD COORDINATE EXACT PLACEMENT OF ALL DEVICES TO PREVENT CONFLICTS - RELOCATE AS
REQUIRED. SYSTEM SHALL BE MONITORED BY AN APPROVED CENTRAL STATION. FURNISH AND INSTALL ALL
POWER AND FIRE ALARM INTERFACE CONNECTIONS INDICATED INDICATED AND AS REQUIRED TO SUPPORT
EXISTING EQUIPMENT AND SYSTEMS. FURNISH AND INSTALL A DEDICATED 120 VOLT POWER CIRCUIT FOR EACH
POWER SUPPLY CABINET AS REQUIRED.
IT IS FURTHER INTENDED THAT UPON COMPLETION OF THIS WORK, THE OWNER BE PROVIDED WITH:
COMPLETE INFORMATION AND DRAWINGS DESCRIBING AND DEPICTING THE ENTIRE SYSTEM AS INSTALLED,
INCLUDING ALL INFORMATION NECESSARY FOR MAINTAINING, TROUBLESHOOTING AND/OR EXPANDING THE
SYSTEM AT A FUTURE DATE.
COMPLETE DOCUMENTATION OF SYSTEM TESTING.
CERTIFICATION THAT THE ENTIRE SYSTEM HAS BEEN INSPECTED AND TESTED, IS INSTALLED ENTIRELY IN
ACCORDANCE WITH THE APPLICABLE CODES, STANDARDS, MANUFACTURER'S RECOMMENDATIONS AND UL
LISTINGS AND IS IN PROPER WORKING ORDER. CONTRACTOR SHALL USE "FIRE ALARM SYSTEM
CERTIFICATION AND DESCRIPTION" AS REQUIRED BY NFPA 72.
NOTE: THE INFORMATION CONTAINED ON THESE DRAWINGS IS DIAGRAMMATIC AND IS INTENDED TO INDICATE
AREAS AND TYPE OF COVERAGE. ALL SYSTEM COMPONENTS AND INITIATION/NOTIFICATION APPLIANCE LAYOUTS
ARE NOT INDICATED ON DRAWINGS - THE DESIGN AND APPROVAL OF THIS SYSTEM SHALL BE THE FIRE ALARM
CONTRACTOR'S RESPONSIBILITY AND SHALL BE BASED ON STANDARD PRODUCTS OFHONEYWELL/NOTIFIER
SYSTEM COMPONENTS TO MEET OR EXCEED ALL REQUIREMENTS OF THE AUTHORITY HAVING JURISDICTION (AHJ).
FINAL APPROVAL OF OVERALL SYSTEM LAYOUT SHALL BE RESERVED BY THE ENGINEER. NO EQUALS WILL BE
CONSIDERED.
1.1 SYSTEM OVERVIEW
1.1.1
THE NEW FIRE ALARM SYSTEM IS TO BE DESIGNED UTILIZE THE EXISTING CONTROL PANEL AND TO
REPORT TO THE SUPERVISORY SERVICE THROUGH EXISTING ALARM COMMUNICATOR.
1.1.2
ALL INITIATING CIRCUITS ARE TO BE ARRANGED TO MATCH THE EXISTING SYSTEM IN ACCORDANCE
WITH NFPA 72. ALL WIRING SHALL BE CONCEALED ABOVE LAY-IN CEILINGS WHEN POSSIBLE AND
INSTALLED IN RACEWAY SYSTEMS WHEN EXPOSED OR WITHIN WALLS AND NON-ACCESSIBLE CEILING
SPACES.
1.1.3
1.1.4
ALL NOTIFICATION APPLIANCE CIRCUITS ARE TO BE ARRANGED TO MATCH THE EXISTING SYSTEM IN
ACCORDANCE WITH NFPA 72. ALL WIRING SHALL BE CONCEALED ABOVE LAY-IN CEILINGS WHEN
POSSIBLE AND INSTALLED IN RACEWAY SYSTEMS WHEN EXPOSED OR WITHIN WALLS AND
NON-ACCESSIBLE CEILING SPACES.
ALL SIGNALING LINE CIRCUITS ARE TO BE ARRANGED TO MATCH THE EXISTING SYSTEMIN ACCORDANCE
WITH NFPA 72. ALL WIRING SHALL BE CONCEALED ABOVE LAY-IN CEILINGS WHEN POSSIBLE AND
INSTALLED IN RACEWAY SYSTEMS WHEN EXPOSED OR WITHIN WALLS AND NON-ACCESSIBLE CEILING
SPACES.
1.2 FIRE ALARM CONTROL SYSTEM:
1.2.1
THE EXISTING FIRE ALARM SYSTEM IS TO BE EXPANDED TO INCLUDE A MICROPROCESSOR-BASED
VOICE EVACUATION SYSTEM CAPABLE OF TWO-WAY COMMUNICATION OVER A NETWORK OF
SIGNALING LINE CIRCUITS THOUGHT OUT THE DESIGNATED HIGH SCHOOL CONSISTING OF NEW
AND EXISTING CONSTRUCTION. INTELLIGENT/ANALOG ADDRESSABLE INITIATING DEVICES SHALL
COMMUNICATE WITH THE EXISTING FACP AND THE FACP SHALL COMMUNICATE THROUGH THE
DACT. A NEW REMOTE ANNUNCIATOR SHALL BE INSTALLED AT THE NEW LOBBY OUTSIDE THE
RECEPTION AREA . FURNISH AND INSTALL ALL POWER SUPPLY CONNECTIONS TO FACP AND
ELECTRIC BELLS ASSOCIATED WITH SPRINKLER SYSTEM. SUPERVISE ALL FLOW, TAMPER AND
LOW PRESSURE SWITCHES ASSOCIATED WITH THE SPRINKLER RISER SYSTEM AND OR FIRE PUMP
AS APPLICABLE. SUPERVISE ALL TAMPER VALVES, AND ETC. ASSOCIATED WITH THE ELEVATOR
SYSTEM AS APPLICABLE. THE SYSTEM SHALL INCLUDE, BUT NOT BE LIMITED TO; FIREMAN'S
CONTROL PANEL, REMOTE ANNUNCIATOR AND INITIATION/NOTIFICATION APPLIANCES.
1.3 INITIATING FUNCTIONS
1.3.1
1.3.2
MANUAL PULL STATIONS ARE TO BE LOCATED AT EXITS OF THE BUILDING ON ALL FLOORS PER
APPLICABLE CODE. ADDITIONAL PULL STATIONS ARE TO BE PROVIDED SO THE TRAVEL DISTANCE
TO A PULL STATION DOES NOT EXCEED 200 FT. MANUAL PULL STATIONS ARE TO BE INSTALLED AT
EXTERIOR EGRESS DOORS FROM MECHANICAL, ELECTRICAL AND OR SPRINKLER ROOMS AS
APPLICABLE.
ADDRESSABLE AREA (SPOT) SMOKE DETECTORS GENERALLY ARE TO BE LOCATED IN VARIOUS
AREAS OF THE BUILDING AS REQUIRED TO PROVIDE PROTECTION OF THE SPACES INDICATED,
SPECIFICALLY STORAGE ROOMS, MECHANICAL AND ELECTRICAL ROOMS. A SMOKE DETECTOR
SHALL BE INSTALLED FOR COVERAGE OF TO SYSTEM AUXILIARY AND CONTROL PANELS. SMOKE
DETECTORS WITH INTERGAL CARBON MONOXIDE (CO) DETECTION AS REQUIRED FOR FULL
COMPLIANCE WITH ILLINOIS STATE BOARD OF EDUCATION (ISBE) Health/Life Safety Code.
1.3.3
ADDRESSABLE HEAT DETECTORS GENERALLY ARE TO BE LOCATED AS REQUIRED TO PROVIDE
PROTECTION OF THE SPACES INDICATED IN CRITICAL AREAS THAT ARE NOT SUITABLE FOR
SMOKE DETECTORS, SUCH AS DUSTY OR HIGH HUMIDITY AREAS.
1.3.4
ANALOG/ADDRESSABLE TYPE DUCT DETECTORS MUST BE LOCATED DOWNSTREAM OF AIR
FILTERS AND AHEAD OF ANY BRANCH CONNECTIONS IN RETURN AIR DUCT OF HVAC UNITS HAVING
A RATED CAPACITY GREATER THAN 2,000 CFM OR IN BOTH THE RETURN AND SUPPLY AIR DUCT OF
UNITS RATED GREATER THAN 15,000 CFM. THESE DETECTORS WILL SHUT DOWN THEIR
RESPECTIVE HVAC UNIT UPON DETECTION OF SMOKE, AND SHALL SOUND THE GENERAL
BUILDING ALARM.
1.3.5
1.3.6
ELECTRICAL NOTES
1. CONTRACTOR SHALL CUT AND PATCH AS REQUIRED DURING THE COURSE OF INSTALLATION OR AS
SPECIFIED ON THE DRAWINGS. ALL PATCHING SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR
WHOSE TRADE CAUSED THE NEED. THE GENERAL CONTRACTOR SHALL BE RETAINED TO PERFORM
PATCHING AND THE COSTS BORNE BY THE CONTRACTOR REQUIRING THE PATCH.
2. ALL NEW ELECTRICAL WORK SHALL BE INSTALLED IN ACCORDANCE WITH THE LATEST EDITION OF
THE NATIONAL ELECTRICAL CODE AND ALL OTHER LOCAL, STATE AND NATIONAL CODES WHICH
APPLY AS INTERPRETED BY THE AHJ (AUTHORITY HAVING JURISDICTION).
3. ALL WORK IS TO BE COORDINATED WITH ALL OTHER TRADES ON THIS PROJECT AND ELECTRICAL
WORK INSTALLED IN A NEAT AND ORDERLY FASHION. THE CONTRACTOR SHALL FURNISH AND
INSTALL ALL ELECTRICAL SYSTEMS AND EQUIPMENT AS INDICATED ON THESE DRAWINGS UNLESS
NOTED.
4. THE ELECTRICAL DRAWINGS ARE SCHEMATIC IN NATURE AND SHOW THE GENERAL ARRANGEMENT
OF EQUIPMENT. THE DRAWINGS SHALL NOT BE SCALED TO DETERMINE EQUIPMENT CONNECTION
OR ROUGH-IN, REFER TO EQUIPMENT CUT-SHEETS AND RESPONSIBLE TRADES. COORDINATION OF
OUTLETS SHALL BE MADE WITH MILLWORK AND CABINETRY DETAILS SHOWN ON THE
ARCHITECTURAL DRAWINGS. COORDINATE PLACEMENT OF ROUGH-INS FOR BACK BOXES TO AVOID
BACK-TO-BACK INSTALLATIONS THAT MAY RESULT IN CLEARANCE AND SOUND TRANSFER ISSUES.
BOXES MAY BE SHIFTED SLIGHTLY AS REQUIRED TO COORDINATE THE INSTALLATION.
5. ALL CONDUCTORS OF THE ELECTRICAL SYSTEM SHALL BE COPPER, 600V, THW/THWN AND SIZED AS
REQUIRED FOR LOADING AND PER CODE. ALL UNDERGROUND CONDUCTORS AND SPLICES MUST BE
LISTED AS SUITABLE FOR WET LOCATIONS. IDENTIFICATION OF CONDUCTORS SHALL BE IN
COMPLIANCE WITH NEC 210.5.
6. NEUTRAL CONDUCTORS SHALL NOT BE SHARED BETWEEN MULTIPLE SINGLE PHASE CIRCUITS OF A
3-PHASE, 4-WIRE HOME RUN - NEUTRALS SHALL BE DEDICATED PER CIRCUIT - REFER TO NEC
ARTICLE 200.4.
7. ALL CONDUIT SHALL BE EMT AND FMC - MINIMUM 1/2" TRADE SIZE (UNLESS SPECIFICALLY
OTHERWISE INDICATED), WHEN INSTALLED INDOORS IN DRY LOCATIONS, RMC WHEN INSTALLED
OUTDOOR OR INDOORS IN DAMP\WET LOCATIONS, RMC AND LFMC WHEN EXPOSED OUTDOORS AND,
RMC OR RNC-40 WHEN INSTALLED IN CONCRETE OR BELOW GRADE. FINAL CONNECTIONS TO ALL
EQUIPMENT WHICH PRODUCE VIBRATION SHALL BE WITH FLEXIBLE METAL CONDUIT SUITABLE FOR
THE SURROUNDING ENVIRONMENT. CONDUIT TURNING UP FROM BELOW GRADE OR FROM WITHIN
CONCRETE SHALL BE RMC. USAGE OF MC CABLE SHALL BE LIMITED TO A MAXIMUM LENGTH OF 72
INCHES, INSTALLED IN ACCESSIBLE SPACES ONLY - SPECIFIC APPROVAL BY THE ENGINEER IS
REQUIRED.
8. RACEWAY FILL, WHEN RACEWAY SIZE IS NOT SPECIFICALLY INDICATED, SHALL BE BASED ON
APPLICABLE ARTICLES OF THE NEC.
9. CIRCUIT ROUTING, IN GENERAL, IS NOT SPECIFIED UNLESS SPECIFIC REQUIREMENTS EXIST WHERE
ROUTING OF CIRCUITS WILL HAVE EFFECTS ON CIRCUIT VOLTAGE DROPS. THEREFORE,
CONTRACTOR SHALL COORDINATE ROUTING LENGTH WITH CONNECTED LOAD AND ADJUST
CONDUCTOR SIZE FOR A VOLTAGE DROP LESS THAN 3%.
10. ALL CONDUITS SHALL BE INSTALLED CONCEALED IN SPACES OF NEW CONSTRUCTION, WHICH ARE
TYPICALLY OCCUPIED. CONTRACTOR SHALL COORDINATE THE LOCATION OF ALL EQUIPMENT TO
MAINTAIN ACCESS REQUIRED BY THE NEC AND EQUIPMENT MANUFACTURERS.
11. SERVICE VOLTAGE AND ELECTRICAL REQUIREMENTS OF ALL EQUIPMENT SHALL BE VERIFIED BY
THE CONTRACTOR PRIOR TO ELECTRICAL ROUGH-IN. DISCREPANCIES BETWEEN THE ELECTRICAL
DRAWINGS AND EQUIPMENT REQUIREMENTS SHALL BE REPORTED TO THE ENGINEER BEFORE ANY
ASSOCIATED WORK IS INSTALLED.
12. COORDINATE WITH THE ARCHITECTURAL DRAWINGS FOR ALL FIRE AND SMOKE RATED BARRIERS.
E.C SHALL FURNISH AND INSTALL APPROPRIATE AND LISTED SEALS FOR ALL PENETRATIONS MADE
IN THESE BARRIERS AS REQUIRED FOR THE INSTALLATION OF THE ELECTRICAL AND SPECIAL
SYSTEMS.
13. CONTRACTOR SHALL COORDINATE WITH THE G.C. AND PROVIDE THE REQUIRED SUPPORT OF
LIGHTING FIXTURES AND BLOCKING NECESSARY TO SUPPORT ALL ELECTRICAL EQUIPMENT.
SUPPORT WIRES INSTALLED IN AREAS WITHIN DROPPED CEILING AREAS SHALL BE DISTINGUISHED
BY COLOR, TAGGING OR PERMANENT EFFECTIVE MEANS - REFER TO NEC 300.11(A)(2).
14. INDEXES OF ELECTRICAL PANELS SHALL BE COMPLETED FOR EACH CIRCUIT. DESCRIPTION SHALL
INCLUDE ROOM NUMBER TO MATCH SIGNAGE AND SHALL BE APPROVED BY ARCHITECT AND OWNER.
ARC-FLASH WARNING LABELS SHALL BE APPLIED ON ALL EQUIPMENT PER NEC 110.24. LABELS AND
TAGS AS DETAILED SHALL BE PLACED ON ALL PANELS, STARTERS, DISCONNECTS, AND ETC.
15. CONTRACTOR SHALL PROVIDE ALL LABOR AND MATERIAL TO CONNECT EQUIPMENT SPECIFIED AS
PART OF THIS PROJECT AND SHALL REVIEW ALL PARTS OF THE CONSTRUCTION DOCUMENTS FOR
LOCATION AND QUANTITIES.
16. CONTRACTOR SHALL REFERENCE THE PROJECT SITE PLANS FOR ELECTRIC, TELEPHONE AND
CABLE T.V. UTILITIES. COORDINATE ALL REQUIRED WORK WITH ASSOCIATED UTILITIES BEFORE
BIDDING AND INCLUDE ALL MATERIAL AND LABOR REQUIRED BY THE RESPECTIVE UTILITY AND
DEEMED "THE OWNERS RESPONSIBILITY" BY THAT UTILITY COMPANY. IN CASE OF DISCREPANCIES
BETWEEN THE CONSTRUCTION DOCUMENTS AND UTILITY COMPANY REQUIREMENTS, THE
REQUIREMENTS OF THE UTILITY COMPANY SHALL BE FOLLOWED AND THE COST THEREOF SHALL BE
INCLUDED IN THE BID.
17. CONTRACTOR SHALL BE REQUIRED TO FABRICATE AND INSTALL ANY NECESSARY STANCHION
MOUNTS FOR ALL ELECTRICAL EQUIPMENT THAT IS NECESSARY TO COMPLETE THEIR WORK.
18. CONTRACTOR SHALL NOTE THAT LIGHT FIXTURE LOCATED IN MECHANICAL ROOMS SHALL BE FIELD
ADJUSTED TO CLEAR DUCTWORK, EQUIPMENT AND BUILDING STRUCTURE.
19. CONTRACTOR SHALL BE RESPONSIBLE FOR RECEPTACLE HEIGHTS LOCATED IN MILLWORK.
REFERENCE ARCHITECTURAL DRAWINGS FOR MILLWORK DETAILS. ALL GFCI RECEPTACLES SHALL
BE INSTALLED IN READILY ACCESSIBLE LOCATIONS. ALL 120V RECEPTACLES INSTALLED IN KITCHEN
AREAS SHALL BE GFCI PROTECTED.
20. EACH WIRING DEVICE (RECEPTACLES AND LIGHTING CONTROLS) SHALL BE LABELED AT THE
FACEPLATE. EACH LABEL SHALL CONSIST OF THE PANEL NAME AND CIRCUIT NUMBER. THE
CHARACTERS SHALL BE A MINIMUM OF 3/16" HIGH
21. ROOM NAME AND NUMBERS USED IN THESE DOCUMENTS ARE FOR REFERENCE DURING
CONSTRUCTION ONLY. OWNER WILL DESIGNATE ROOM NUMBER AND NAMES TO BE USED FOR
PANEL INDEXES AND EQUIPMENT LABELING. COORDINATE WITH THE ARCHITECT.
SYMBOL
RECESSED LIGHT FIXTURE AS SCHEDULED
MOUNTING
AS NOTED
AS NOTED
PENDANT STRIP LIGHT FIXTURE AS SCHEDULED
AS NOTED
WALL MOUNTED LINEAR LIGHT FIXTURE AS SCHEDULED
AS NOTED
S
FIRE ALARM CONTROL PANEL
FAA
FIRE ALARM REMOTE ANNUNCIATOR PANEL
60" TO
CENTER AFF
F
FIRE ALARM HORN/STROBE - AUDIBLE/VISUAL
F
PER DETAIL
FIRE ALARM STROBE - VISUAL
PER DETAIL
FIRE ALARM PULL BOX
PER DETAIL
CEILING PER
CODE
ADDRESSABLE FIRE ALARM SYSTEM
CFCI
CFCI
CFCI
STANDBY EMERGENCY GENERATOR SYSTEM FOR
E-LTG, RECEPTACLES AT CIRCULATION DESK, FIRE
ALARM, DEMARC BOARD, AND NETWORK ROOMS
CFCI
CFCI
CFCI
UPS BACKUP POWER FOR NETWORK RACKS
CFCI
CFCI
OFOI
SURGE PROTECTION DEVICES FOR PANELBOARDS
CFCI
CFCI
CFCI
AUTOMATED LIGHTING CONTROLS - LOCALIZED
AREAS - OCCUPANCY SENSOR
CFCI
CFCI
CFCI
SYSTEM SMOKE DETECTOR
CEILING PER
CODE
AUTOMATED LIGHTING CONTROLS - CENTRALIZED
DIGITAL SYSTEM FOR COMMONS AREAS
CFCI
CFCI
CFCI
SYSTEM DUCT DETECTOR
DUCTWORK,
PER HVAC
POE CLOCK SYSTEM
CFCI
CFCI (ALT BID A-1)
OFOI
ELEVATOR STATUS RECALL
COORD WITH
UNIT
EMPLOYEE TIME CLOCKS
CFCI
CFCI (ALT BID A-1)
OFOI
DOOR ACCESS CONTROLS AND HARDWARE
CFCI
CFCI
OFOI (2)
PUBLIC ADDRESS SYSTEM
CFCI
CFCI (ALT BID A-1)
OFOI (1)
DUAL HEAD EMERGENCY WALL PACK
PER DETAIL
FLOOD LIGHT AS SCHEDULED
AS NOTED
ROUND RECESSED LIGHT AS SCHEDULED
AS NOTED
SURFACE MOUNTED STRIP LIGHT AS SCHEDULED
AS NOTED
POWER SUPPLY OR BATTERY AS SCHEDULED
AS NOTED
SINGLE POLE LIGHTING SWITCH WITH PILOT LIGHT
PER DETAIL
DIMMER SWITCH - SIZED PER LOAD AND COMPATIBLE WITH LAMP
SOURCE
PER DETAIL
S
D
ESR
COMMUNICATIONS SYSTEMS - VOICE/DATA/INTERCOM
TECHNOLOGY VOICE/DATA OUTLETS - V# INDICATES NUMBER OF
VOICE PORTS AND CABLES DROPS. D# INDICATES NUMBER OF
DATA PORTS AND CABLES DROPS. A# INDICATES NUMBER OF
ANALOG PORTS AND CABLES. R# INDICATES NUMBER OF RCA
JACKS AND CABLES. REFER TO DEVICE MOUNTING HEIGHT
DETAIL.
V#
D#
A#
R#
D#
SENSOR AND LIGHTING AUTOMATION NOTE:
FURNISH AND INSTALL SENSORS, POWER PACKS AND ALL LIGHTING AUTOMATION DEVICES
APPROXIMATELY AS INDICATED ON PLAN VIEW AND AS REQUIRED BY NUMBER OF CIRCUITS OF
LIGHTING WITHIN THE SPACE. PLACEMENT OF SENSORS SHALL BE BASED ON ROOM
GEOMETRY AND SHALL PROVIDE 100% COVERAGE OF THE SPACE - FIELD COORDINATE WITH
MANUF. RECOMMENDATIONS. ALL SYSTEM COMPONENTS SHALL BE WIRED PER THE
MANUFACTURER'S RECOMMENDATIONS. CONTRACTOR SHALL COORDINATE TIME AND
SENSITIVITY SETTINGS OF EQUIPMENT WITH OWNER'S PREFERENCES. INFO ABOVE IS BASED
ON SENSOR SWITCH OCCUPANCY SENSORS AND PERFORMANCE AND MAY VARY, PENDING
MANUFACTURER. MANUFACTURER SHALL PROVIDE A GUARANTEED LAYOUT TO THE
CONTRACTOR AND SHALL ALSO SUBMIT LAYOUT IN SHOP DRAWINGS.
W
V#
D#
S
L
S
MOUNTING
CFCI
CFCI
VIDEO DISTRIBUTION SYSTEM (TVs) - IP BASED CAT 6
CFCI
CFCI (ALT BID A-1)
OFOI
TV MOUNTING BRACKETS
CFCI
CFCI
OFCI
VIDEO SURVEILLANCE SYSTEM (CCTV) INTERIOR/EXTERIOR - IP BASED WITH NVR
CFCI
CFCI (ALT BID A-1)
OFOI
BOOK SECURITY SYSTEM
CFCI
CFCI (ALT BID A-1)
OFOI
SHORT THROW PROJECTOR
CFCI
CFCI (ALT BID A-1)
OFOI
CEILING PROJECTOR MOUNTING PLATES
CFCI
CFCI
OFCI
POE PEOPLE COUNTERS
CFCI
CFCI (ALT BID A-1)
OFOI
PORTABLE DEVICES AND POE TO USB POWER
SUPPLIES FOR MEETING ROOM SCHEDULE SIGNAGE
(POE)
CFCI
OFOI
OFOI
PORTABLE DEVICE MOUNTING ENCLOSURES (POE)
CFCI
CFCI (ALT BID A-1)
CFCI
PER DETAIL
WALL MOUNTED PA SPEAKER.
PER DETAIL
S
CEILING/SURFACE MTD SPEAKER
PER DETAIL
C
WALL MOUNTED POE CLOCK.
COORDINATE
PER PLANS
72" TO TOP
A.F.F.
POWER CONNECTION TO EQUIPMENT
FIELD
COORDINATE
JUNCTION BOX FOR CONNECTIONS TO EQUIPMENT
FIELD
COORDINATE
HEAVY DUTY NON-FUSED DISCONNECT SWITCH - SIZE AS NOTED
ON EQUIPMENT SCHEDULE
AS NOTED,
PER CODE
HEAVY DUTY FUSED DISCONNECT SWITCH - SIZE AS NOTED ON
EQUIPMENT SCHEDULE
AS NOTED,
PER CODE
ROUGH-IN FOR THERMOSTAT WITH 3/4"C FROM SINGLE GANG
BOX TO CEILING SPACE.
COORD WITH
TCC/MC
COORDINATE
WITH
EQUIPMENT
CFCI
PER DETAIL
FIELD
COORDINATE
MANUAL MOTOR STARTER SWITCH W/O OVERLOADS, SUITABLY
SIZED AND RATED FOR RESISTIVE TYPE LOADS, TO SERVE AS
LOCAL DISCONNECT
CABLE TRAY SYSTEM
PA SYSTEM LEVEL CONTROL ATTENUATOR.
120V, 20 AMP DUPLEX RECEPTACLE MOUNTED FLUSH IN CEILING
TILE FOR CONNECTION TO EQUIPMENT.
THE STROBES SHALL BE PLACED 80 IN. ABOVE THE HIGHEST FLOOR LEVEL WITHIN THE
SPACE OR 6 IN. BELOW THE CEILING, WHICHEVER IS LOWER.
OFCI
OFOI
FIELD
COORDINATE
1.4.1.6
CFCI (ALT BID A-1)
CFCI (ALT BID A-1)
1-COMPARTMENT FLUSH FLOOR BOX WITH POWER OUTLET - SEE
DETAIL.
COORD.
PLACEMENT
CFCI
CFCI
16" TO BTM
AFF UON
FLUSH FLOORBOX - CONTRACTOR TO COORDINATE PLACEMENT
AND COVERS WITH DESIGN DRAWINGS. SEE DETAIL DRAWING
AND TAG NOTES.
NETWORK RACKS FOR MDF
CEILING MOUNTED PROJECTOR
125/250V RECEPTACLE FOR APPLIANCE USE - NEMA 14-50R, UON
THE FLASH RATE SHALL BE A MINIMUM OF 1 HERTZ AND A MAXIMUM OF 3 HERTZ.
OFOI (3)
OFCI
CENTRAL INTERCOM EQUIPMENT PANEL
1.4.1.5
CFCI (ALT BID A-1)
CFCI
44" TO BTM
AFF UON
THE INTENSITY SHALL BE A MINIMUM OF 75 CANDELA IN ACCORDANCE WITH UL.
CFCI
CFCI
120V, 20 AMP DUPLEX RECEPTACLE AT SPECIAL MOUNTING
HEIGHT - REFER TO ARCHITECTURAL MILLWORK DRAWINGS
1.4.1.4
WAP (WIRELESS ACCESS POINT) - CAT 6 POE
SHORT THROW MOUNTING BRACKET
GENERATOR ANNUNCIATOR PANEL
48" TO TOP
AFF UON
OFOI (3)
COORD.
PLACEMENT
44" TO BTM
AFF UON
MUSHROOM HEAD MASTER KILL SWITCH FOR ROOM CONTACTOR
- RED IN COLOR - LOOP CONTROL CIRCUIT OF CONTACTOR
THROUGH SWITCH PER MANUFACTURER'S RECOMMENDATIONS
CFCI (ALT BID A-1)
WIRE BASKET TYPE CABLE TRAY SYSTEM, AS INDICATED - SEE
SPECIAL SYSTEMS AND COMMUNICATIONS DETAILS.
120V, 20 AMP DUPLEX RECEPTACLE AT SPECIAL MOUNTING
HEIGHT - REFER TO ARCHITECTURAL MILLWORK DRAWINGS
THE MAXIMUM PULSE DURATION SHALL BE 2/10TH OF ONE SECOND (0.2 SECONDS) WITH A
MAXIMUM DUTY CYCLE OF 40 PERCENT. THE PULSE DURATION IS DEFINED AS THE TIME
INTERVAL BETWEEN INITIAL AND FINAL POINTS OF 10 PERCENT OF MAXIMUM SIGNAL.
CFCI
FIELD
COORDINATE
16" TO BTM
AFF UON
1.4.1.3
DATA SYSTEM (TRADITIONAL) - CAT 6
FLOORBOX TECHNOLOGY VOICE/DATA OUTLETS - SEE
COMMUNICATION DETAIL. V# INDICATES NUMBER OF VOICE
PORTS AND CABLE DROPS. D# INDICATES NUMBER OF DATA
PORTS AND CABLE DROPS. REFER TO PERSPECTIVE VIEW AND
OUTLET DETAIL.
120V, 20 AMP QUADRUPLEX RECEPTACLE (DOUBLE DUPLEX)
THE COLOR SHALL BE CLEAR OR NOMINAL WHITE (I.E., UNFILTERED OR CLEAR FILTERED
WHITE LIGHT).
OFOI (3)
PER DETAIL
16" TO BTM
AFF UON
1.4.1.2
CFCI (ALT BID A-1)
OUTLET FOR WALL MOUNT TELEPHONE. V# INDICATES NUMBER
OF VOICE PORTS AND CABLE DROPS.
120V, 20 AMP DUPLEX RECEPTACLE MOUNTED PERPENDICULAR
TO FLOOR.
THE LAMP SHALL BE A NEON STROBE TYPE OR EQUIVALENT.
CFCI
CEILING OR
WALL
POWER SYSTEM
ITEM DESCRIPTION AND REMARKS
VOICE OVER IP SYSTEM (VOIP) - CAT 6
WIRELESS ACCESS POINT (WAP) - LABEL "WIFI". D# INDICATES
NUMBER OF DATA PORTS AND CABLE DROPS.
LAY-IN CEILING SPEAKER
ABBREVIATION - DESCRIPTION:
CFCI - CONTRACTOR FURNISHED, CONTRACTOR INSTALLED - PER SPECIFICATIONS.
OFCI - OWNER FURNISHED, CONTRACTOR INSTALLED - PER SPECIFICATIONS.
72" TO TOP
A.F.F.
OFOI - OWNER FURNISHED, OWNER INSTALLED.
NIC - NOT IN CONTRACT.
SPECIAL SYSTEMS - DOOR ACCESS/SECURITY
(1) - PA/SOUND SYSTEM BASE EQUIPMENT, SPEAKERS AND VOLUME CONTROL DEVICES BY OWNER.
POE PEOPLE COUNTER.
CEILING
DL
DOOR ACCESS ELECTRIC STRIKE - REFER TO ARCHITECTURAL
DRAWINGS AND HARDWARE SPECIFICATIONS
COORDINATE
CR
DOOR ACCESS CONTROL READER AND NETWORK DOOR
CONTROLLER - REFER TO ARCHITECTURAL DRAWINGS AND
HARDWARE SPECIFICATIONS
COORDINATE
D
REQUEST TO EXIT SENSOR - REFER TO ARCHITECTURAL
DRAWINGS AND HARDWARE SPECIFICATIONS
COORDINATE
WALL MTD POE SECURITY CAMERA.
PER DETAIL 5,
DWG. E-4.2
CEILING MTD POE SECURITY CAMERA.
PER DETAIL 6,
DWG. E-4.2
CENTRAL CONTROL BASE STATION "AREA OF REFUGE" - REF.
DETAIL 1, DRAWING E-4.2.
EMERGENCY CALL BOX "AREA OF REFUGE - REF. DETAIL 1,
DRAWING E-4.2.
C
E
(2) - REFER TO ARCHITECTURAL DOOR HARDWARE SPECIFICATION. CONTRACTOR SHALL FURNISH AND INSTALL ALL CONDUIT,
ROUGH-INS, POWER REQUIREMENTS, FIRE ALARM SYSTEM CONNECTIONS AND ETC, AS REQUIRED BY SPECIFICATIONS.
COORDINATE WITH SHOP DRAWING SUBMITTALS PRIOR TO ROUGH-IN AND INSTALL PER MANUFACTURER'S RECOMMENDATIONS.
(3) - CONTRACTOR SHALL FURNISH AND INSTALL PATCH PANELS.
ABBREVIATIONS
AFF
ABOVE FINISHED FLOOR
BTM
BOTTOM
WALL @ 60"
TO CNTR
A.F.F.
DW
DISHWASHER
EC
ELECTRICAL CONTRACTOR
WALL @ 48"
TO CNTR
A.F.F.
EGFCI
1.4.2.2
FDS
FUSED DISCONNECT SWITCH
GFI
GROUND FAULT INTERRUPTING DEVICE
HR
INDICATES DEVICE IS HUMIDITY RESISTANT
HACR
HEATING AND AIR-CONDITIONING RATED DEVICE
IG
ISOLATED GROUND DEVICE
LOC
EQUIPMENT LOCK OUT CLIP
MC
MECHANICAL CONTRACTOR
NO PLACE IN COMMON CORRIDORS OR HALLWAYS IN WHICH VISUAL ALARM SIGNALING
APPLIANCES ARE REQUIRED SHALL BE MORE THAN 50 FT. FROM THE SIGNAL.
1.4.1.9
VISUAL SIGNALING (STROBE) APPLIANCES SHALL BE LOCATED WITHIN 15 FT. OF THE END
OF A CORRIDOR.
MCB
MAIN CIRCUIT BREAKER
1.4.1.10
WHEN TWO OR MORE VISUAL SIGNALING APPLIANCES MAY BE VIEWED AT ONE TIME,
THEY SHALL FLASH IN SYNCHRONIZATION.
MLO
MAIN LUGS ONLY
1.4.1.11
AREAS REQUIRED TO HAVE VISUAL SIGNALING APPLIANCES INCLUDE BUT ARE NOT
LIMITED TO: CORRIDORS, RESTROOMS, CONFERENCE AND MEETING ROOMS,
CLASSROOMS, FILING AND PHOTOCOPY ROOMS, BREAK ROOMS AND SIMILAR SPACES.
MW
MICROWAVE
NFDS
1.4.2.4
UNLESS NOTED OTHERWISE ALL AUDIO ALARM DEVICES INSTALLED IN ROOMS WITH LAY-IN CEILING
SHALL BE INSTALLED IN THE CEILING.
OVERHEAD PROJECTOR
ST
SHUNT TRIP DEVICE
TCC
TEMPERATURE CONTROL CONTRACTOR
TV
TELEVISION
UG
UNDERGROUND
UON
THE VOICE CONTROL PANEL SHALL INCORPORATE A MICROPHONE WHICH IS CAPABLE OF
OVERRIDING ANY OR ALL CIRCUITS, WHETHER ACTIVATED OR NOT, ON A SELECTABLE BASIS. THIS
PROVIDES THE CAPABILITY OF ADDRESSING ALL CIRCUIT AUDIBLE DEVICES THROUGH AN ALL-PAGE
FEATURE SIMULTANEOUSLY.
THE VOICE CONTROL PANEL SHALL BE CAPABLE OF PRODUCING TEXTUAL MESSAGES. INDIVIDUAL
TEXTUAL MESSAGES PRODUCED BY THE VOICE CONTROL PANEL WILL REPEAT CONTINUOUSLY
UNTIL SILENCED AT THE FACP. IN THE EVENT OF FAILURE OF THE DIGITAL MESSAGES TO BE
PRODUCED, THE BUILDING VOICE CONTROL PANEL MUST AUTOMATICALLY PROVIDE A CONTINUOUS
ALERT TONE. A REMOTE MICROPHONE STATION SHALL BE PROVIDED FOR PAGING FUNCTION.
FIXTURE IS DESIGNATED NIGHT LIGHT 24 HOUR CONTINUOUS RUN
OHP
THE SPEAKERS SHOULD BE ACTUATED THROUGH THE MAIN VOICE CONTROL PANEL LOCATED AT
THE FACP AND BE CAPABLE OF PROVIDING A SOUND LEVEL WHICH IS A MINIMUM OF 85 DBA. IN NO
CASE SHALL THE RATED OUTPUT OF A HORN BE LESS THAN 15 DBA OVER AMBIENT CONDITIONS.
THE VOICE CONTROL PANELS SHOULD BE CAPABLE OF MANUAL SELECTION OF: NORMAL
VOICE/TONE OPERATION; TONE ONLY OPERATION; MANUAL ONLY OPERATION.
1.4.2.3
NON-FUSED DISCONNECT SWITCH
NL
SPEAKER QUANTITY AND SPL SHALL BE SELECTED BASED ACTUAL SITE CONDITIONS AND
INTELLIGIBILITY SHALL BE ACHIEVED AS APPLICABLE BY N.F.P.A. 72
1.4.2 AUDIBLE ALARM DEVICES
1.4.2.1
30mA EQUIPMENT GROUND FAULT CIRCUIT INTERRUPTER
1.4.1.8
1.4.1.12
UNLESS OTHERWISE NOTED
VR
INDICATES DEVICE IS VANDAL RESISTANT
WG
FIXTURE OR DEVICE SHALL HAVE A FACTORY SPEC. WIRE GUARD
WP
WEATHERPROOF DEVICE - WEATHER RESISTANT RATED
ELECTRICAL NOTES AND TAGS
ELECTRICAL DETAIL NUMBER
ELECTRICAL DETAIL TAG
DRAWING WHERE DETAIL IS ILLUSTRATED
1.5 AUXILIARY FUNCTIONS
1.5.1
EMERGENCY EXIT DOORS WITH SECURITY MAGNETIC LOCKS SHALL RELEASE PER NFPA 72.
1.5.2
THE FIRE ALARM SYSTEM OPERATION FOLLOWING THE ACTIVATION OF A MANUAL PULL STATION,
AREA SMOKE DETECTOR, THERMAL DETECTOR, SPRINKLER TAMPER SWITCH, SPRINKLER FLOW
SWITCH OR DUCT TYPE SMOKE DETECTOR SHALL ACTIVATE THE FOLLOWING SEQUENCE:
1.5.2.1
ALL INTENDED ALARM NOTIFICATION APPLIANCES SHALL SOUND CONTINUOUSLY UNTIL
THE FIRE ALARM CONTROL PANEL IS SILENCED BY THE ALARM SILENCE KEY.
1.5.2.2
ALL VISUAL NOTIFICATION APPLIANCES SHALL FLASH CONTINUOUSLY UNTIL THE FIRE
ALARM PANEL IS SILENCED, ALARM CONDITION IS CLEARED AND THE CONTROL PANEL IS
RESET.
1.5.2.3
A SUBSEQUENT ALARM SHALL CAUSE IT'S PROGRAMMED OR INTENDED OUTPUTS TO
ACTIVATE/REACTIVATE.
1.5.2.4
INITIATE TRANSMISSION OF THE ALARM SIGNAL TO REMOTE CENTRAL STATION VIA
EXISTING COMMUNICATOR PER NFPA 72.
1.5.2.5
MECHANICAL CONTROLS SHALL ACTIVATE AIR-HANDLING SYSTEMS IN ACCORDANCE
WITH NFPA 90.
1.5.2.6
ALL SYSTEM EVENTS SHALL BE DISPLAYED ON A FACP DISPLAY AND REMOTE
ANNUNCIATOR.
1.5.2.7
THE CONTROL PANEL SHALL ALARM CONTINUOUSLY UNTIL SILENCED.
1.5.2.8
AN ALARM FROM A ZONE OR DEVICE SELECTED FOR ALARM VERIFICATION SHALL CAUSE
A VISUAL SIGNAL AT THE FACP AND ANNUNCIATOR DURING THE VERIFICATION
SEQUENCE. AN ALARM FROM ANY OTHER DEVICE SUCH AS A PULL STATION, SHALL
OVERRIDE ALARM VERIFICATION AND CAUSE AN IMMEDIATE ALARM.
1.5.2.9
PROVIDE DISTINCT NOTIFICATION OF CARBON MONOXIDE.
1.5.2.10
ACTIVATE NOTIFICATION APPLIANCES ASSOCIATED WITH AND REQUIRED BY THE
SPRINKLER SYSTEM UPON SYSTEM WATER FLOW.
1.5.2.11
OVER RIDE PERFORMANCE SOUND SYSTEM AND MUTE ALL GYM SOUND SYSTEM.
03/01/2018
INFORMATION AND TECHNOLOGY SYSTEMS
PER DETAIL
TECHNOLOGY VOICE/DATA OUTLETS SPECIAL MOUNTING HEIGHT.
V# INDICATES NUMBER OF VOICE PORTS AND CABLES DROPS. D#
PER DETAIL
INDICATES NUMBER OF DATA PORTS AND CABLES DROPS. A#
OR AS NOTED
INDICATES NUMBER OF ANALOG PORTS AND CABLES. R#
ON PLANS
INDICATES NUMBER OF RCA JACKS AND CABLES. REFER TO
DEVICE MOUNTING HEIGHT DETAIL.
V#
D#
A#
R#
V#
LIGHT FIXTURE NOTE:
LIGHT FIXTURE SHOWN WITH HALF SHADING INDICATES FIXTURE WITH INTEGRAL BATTERY
PACKS OR CONNECTED TO EMERGENCY POWER SYSTEM AS SPECIFIED - REFER TO LIGHT
FIXTURE SCHEDULE FOR ADDITIONAL INFORMATION. SUBSCRIPTS INDICATE CIRCUIT NUMBER
AND SWITCHING DESIGNATIONS.
M
GENERAL BUILDING OPERATIONAL SYSTEMS
S
S
S
DISTRIBUTION
EQUIPMENT
AS NOTED
PER DETAIL
T
CABLING
INFRASTRUCTURE
RECESSED DOWN LIGHT FIXTURE AS SCHEDULED
3-WAY LIGHTING SWITCH
J
RACEWAYS/BOXES
HEAT DETECTOR, FIXED TEMPERATURE
1.4.1.1
IN GENERAL, NO PLACE IN ANY ROOM OR SPACE REQUIRED TO HAVE A VISUAL SIGNALING
APPLIANCE SHALL BE MORE THAN 50 FT. FROM THE SIGNAL (IN A HORIZONTAL PLANE). IN
LARGE ROOMS AND SPACES EXCEEDING 100 FT. ACROSS WITHOUT OBSTRUCTION 6 FT.
ABOVE THE FINISHED FLOOR SUCH AS AUDITORIUMS, DEVICES MAY BE PLACED AROUND
THE PERIMETER, SPACED A MAXIMUM OF 100 FT. APART IN LIEU OF SUSPENDING
APPLIANCES FROM THE CEILING.
FACP
CONTRACT SYSTEM DESCRIPTION
H
S3
SYMBOL
ELECTRICAL SPECIAL SYSTEMS OUTLINE
AS NOTED
PER DETAIL
SDM
MOUNTING
RECESSED DOWN LIGHT WALL WASHER FIXTURE AS SCHEDULED
SINGLE POLE LIGHTING SWITCH
P
ITEM DESCRIPTION AND REMARKS
60" TO
CENTER AFF
AS NOTED
EMERGENCY EXIT FIXTURE AS SCHEDULED - ARROW OR SHADING
PER DETAIL
INDICATES EGRESS PATH DIRECTION
VISUAL SIGNAL APPLIANCES (STROBES) MUST BE INSTALLED, AS A MINIMUM, TO CONFORM TO THE
AMERICANS WITH DISABILITIES ACT (ADA) CRITERIA AND NFPA 72. SOME OF THE ADA CRITERIA ARE:
1.4.1.7
SYMBOL
FIRE ALARM SYSTEM
SURFACE MOUNTED LIGHT FIXTURE AS SCHEDULED
WALL MOUNTED LIGHT FIXTURE AS SCHEDULED
1.4 NOTIFICATION FUNCTIONS
1.4.1
ITEM DESCRIPTION AND REMARKS
LIGHTING SYSTEM
WATER FLOW SWITCHES ARE GENERALLY INSTALLED ON SPRINKLER RISERS. SWITCHES SHALL BE
ARRANGED TO INITIATE AN ALARM CONDITION.
TAMPER SWITCHES ARE GENERALLY INSTALLED ON SPRINKLER SYSTEM WATER CONTROL VALVES
AT EACH FLOOR. SWITCHES SHALL BE ARRANGED TO ANNUNCIATE AN OFF-NORMAL CONDITION.
ELECTRICAL SYMBOL LEGEND
ELECTRICAL SYMBOL LEGEND
#
IMPORTANT NOTICE
1. EXTERIOR WALLS FOR THIS BUILDING ARE CONSTRUCTED OF ICF (INSULATED CONCRETE FORM).
THE SUBCONTRACTORS SHALL COORDINATE NECESSARY ROUGH-IN OF SYSTEMS WITHIN WALLS.
THIS MUST BE DONE PRIOR TO THE CONCRETE POUR AND IS THE RESPONSIBILITY OF THE
SUBCONTRACTOR WHO REQUIRES THE PENETRATION OR CONCEALMENT.
2. AT EXTERIOR ICF WALLS, ALL AREAS OF ICF FOAM INSULATION ROUTED OUT FOR ELECTRICAL
CONDUIT, PLUMBING, ETC. SHALL BE SPRAY-FOAMED AND RE-INSULATED AROUND SUCH
INSTALLATION TO RETARD THERMAL TRANSMISSION.
ELECTRICAL CONSTRUCTION NOTE
ELECTRICAL DEMOLITION NOTE
WIRING HOME RUNS
WIRING AND RACEWAY HOME RUN BACK TO POWER SOURCE ABOVE
SLAB. (SEE PLAN VIEW FOR CIRCUIT TAG)
WIRING AND RACEWAY HOME RUN BACK TO POWER SOURCE BELOW
SLAB. (SEE PLAN VIEW FOR CIRCUIT TAG)
ELECTRICAL LEAD SHEET
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-0.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
DD1
9
ELECTRICAL
CONSTRUCTION NOTES
#
MOUNT INSIDE
AWNING @ 8' A.F.F.
CC
corner mount @ 10'
OS
STORAGE
B
BOILER
124
G
G
G
B
OS
B
R EM
3
R
S
DS
C1
S
S
EM
R
OS
FR1
H3
2
OS RR
N1 OS
C1
S
B
B
B
N2
B
R
B
R
S
R
H1
S
S
C
S
C
C
R
C
CIRCULATION
112
H1
M2
DC4
N2
B
2
N1
M1
C
NL
R EM
R
R
EM
C
N1
M1
M1
R
N1
R
L
C
L
M1
A3
C
N1
MEN
L
M1
K
OS
N1
BOOK RETURN
102
C
K
N1
R
A1
E
R
RD-22
E
A2
A3
ZONE 3
R
ZONE 2
A1
A2
E
P
P
A3
E
E
EX1
P
EX1
COLLECTIONS
106
R
E
E
P R
EM R
A3
E
R
OS
E
YOUNG ADULTS
108
E
E
C
B
EM
E
6
RD-23,25
ZONE 1
A3
E
E
C
N1
OS
R
E
E
OS
3
C
E
E
117
B
R
EX1
EM
A3
TO STEP LIGHT FIXTURES "FF". FOR CONTINUATION, REF. DRAWING UE-1.1.
OS
RD-18
RD-21
9
C
WOMEN
NL
R
L
L
C
E
E
TO SITE POLE FLOOD LIGHT FIXTURES "BB3". FOR CONTINUATION, REF. DRAWING
UE-1.1.
E
E
M1
R
E
8
C
116
SDC4
S
E
MOUNT INSIDE
AWNING @ 10' A.F.F.
OF DOCK.
R
K
E
A2
K
C
N2
EX1
7
CUT PRODUCT'S TO LENGTHS AS NOTED IN THE LIGHTING FIXTURE SCHEDULE.
MOUNT ON TOP OF ARCHITECTURAL CLOUDS IN AN INDIRECT FASHION WITH
LIGHT SHINING TOWARDS PRIMARY CEILING. "H" FIXTURES SHALL EVENLY SPAN
AND BE SECURED TO CLOUD T-BAR GRID. POWER SUPPLIES SHALL BE MOUNTED
REMOTE AND CONCEALED ABOVE PRIMARY CEILING. REFERENCE
ARCHITECTURAL PLANS FOR CLOUD T-BAR GRID SYSTEM.
COVERED CANOPY LIGHTING, ALTERNATE BID A-5
IF SELECTED, PROGRAM LIGHTING CONTROL FOR
ON AT DUSK, OFF AT 11 PM.
OS
EX1
C
DS
DC2 DC2 DC4 C1
C
E
E
B
7
N1
N1
DC4
S
C
M2
N2
TO SITE POLE LIGHTING. FOR CONTINUATION, REF. DRAWING UE-1.1.
L
C
H1
B
EM
6
E
E
C
BRANCH MNGR
S
M2
H2
B
C
S
RD-15
R
GP-8
R
FLOOD LIGHTING, REF. DETAIL 11, DRAWING UE-4.1 FOR DETAILS. FLOOD LIGHT
SHALL BE ADJUSTED IN FIELD TO CENTER LIGHT EVENLY OVER WALL MOUNTED
SIGN. PROGRAM LIGHTING CONTROL FOR ON AT DUSK, OFF AT 11 PM.
R
R EM
K
115
S
M2
H2
N2
B
C
M2
N1
EM1
M2
H2
B
114
5
C1
107
7
N1
B
WORKROOM
CHILDREN/JUVENILE
N1
109
B
B
N2
M2
YOUTH PROGRAM
H2
M2
R
N1
RR
CUSTODIAL
118
B RR
N2
B
TO FLAG POLE LIGHTING. FOR CONTINUATION, REF. DRAWING UE-1.1.
R
K
OS
OS
B
B
MOUNT INSIDE
AWNING @ 10' A.F.F.
121
OS
C1
R
B
EM1
B
EM R
EX1
S
R
B
EM
7
M2
M2
B
4
EX2
2
C1
DD2
BOOK MOBILE
G
C
LS-25
EX1STAFF TOILET
119
S
C1
E
123
B
R
N2
N2
CORRIDOR
C
DC1
E
N2
C
OS OS
C1
H1
B
C
EX1
S
R
7
EM1
C
EX1
TOILET
111
C
3
SWITCH IS DESIGNATED AS A REMOTE OVERRIDE FOR INTERIOR LIGHTING
CONTROLLED BY THE TIME CLOCK. REF. DRAWING E-5.4 FOR PROGRAMMING
REQUIREMENTS. E.C. SHALL LABEL SWITCH WITH A PLACARD COMMUNICATING
"LIGHTING REMOTE OVERRIDE".
HM
G
EM1
3
FOR CONTINUATION TO EXHAUST FAN, REF. DRAWING E-1.3. REFERENCE DETAIL 7,
DRAWING E-4.2 FOR CONNECTION DETAILS.
OS
1
R
R
C
G
HM
RD-14
R
2
RD-17 R
G
1
G
FOR CONTINUATION, REF. DRAWING E-1.2.
R
EX1 EM
DD2
125
FR1
DS
C1
G
ELECTRICAL
PLUMBING
G
122
G
C1
1
G
C1
S
HVAC
110
F1 OS
S
BM OFFICE
1
S
STAIR
(APPLIES TO THIS DRAWING ONLY)
R
VESTIBULE
EM
E
E
E
101
E
P R
RD-20
EM R
P
F1
EX1
E
R
E
A1
1
E
A2
A3
OS
STAIR
104
R
FR1
RD-19
ZONE 4
E
R
R
A1
E
R
A2
E
103
R
A1
ELEV.
E
E
ZONE 5
ZONE 6
E
EQUIP.
105
E
CC
FR1
4
A1
A2
A1
E
E
E
8
A1
A2
E
A1
E
E
E
E
E
E
E
E
E
E
E
E
5
BB2
E
E
EX1
FOR CONTINUATION REFERENCE
DRAWING E-1.2 FIXTURE "EE"
CLASSIFIED ASSEMBLY LEGEND
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
ELECTRICAL LIGHTING FIRST FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-1.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
G
ELECTRICAL
CONSTRUCTION NOTES
#
DD1
4
G
MOUNT @ 8' A.F.F.
MOUNT @ 8' A.F.F.
CC
1
G
G
B
2
G
G
MECH/ELEC
222
RA-11
RD-14
S
DC1
RA-11
S
MOUNT @ 8' A.F.F.
R
OS
EM1 EX1
3
S
C1
R
EX1
B
OS
R
EM
EX1
EX1
VESTIBULE N3
OS
212
DS
N3
B
B
RESEARCH
213
B
RR
FAMILY
218
R
OS
B
K
B
OS
C
R
L WOMEN
216
L
M2
B
EM
C
L
DC2
S
M2
R
R
O1
O2
B
C
R
M2
DC2
B
S
EM
MAKER
215
S
C1
RA-18
R
R
C1
A3
M2
R
S
R EM
A3
M2
R
R
EM
M2
C
M2
OS
GP-8
M2
O1
B
B
L
NL
M2
M2
B
OS
L
B
C1
EX1
B
S
N2
B
OS
M2
C
R
A5
K
EX1
DC1
B
C
OS
S
COMPUTER LAB
214
R
K
B
EX1
RA-19
O2
O2
N2
RA-20
2
B
R
N2
C
3
B
OS
B
E
RR
EM1
EM R
DIRECTOR
210
B
R
N3
C
DS
FILES
224
N3
O2
O2
B
E
C
OS
OS
STAFF TOILET
219
B
OS
R
B
OS
B
R
R
HM
EM
OS
B
3
N3
C
C
R
GP-8
B
N3
C
C
E
OS
NL B
O2
R
FROM STEP LIGHT FIXTURES "FF". FOR CONTINUATION, REF. DRAWING UE-1.1.
R
TC
B
OS
N3
4
EM
EM1
FR1
C
FOR CONTINUATION TO EXHAUST FAN, REF. DRAWING E-1.4. REFERENCE DETAIL 7,
DRAWING E-4.2 FOR CONNECTION DETAILS.
1
C
MDF
221
NL
F2
BOOK KEEPER
211
C
C
CORRIDOR
225
B
R
G
S
CC
3
E
E
G
B
2
SWITCH IS DESIGNATED AS A REMOTE OVERRIDE FOR INTERIOR LIGHTING
CONTROLLED BY THE TIME CLOCK. REF. DRAWING E-5.4 FOR PROGRAMMING
REQUIREMENTS. E.C. SHALL LABEL SWITCH WITH A PLACARD COMMUNICATING
"LIGHTING REMOTE OVERRIDE".
C
S C1
SC1D
G
E
C
TECH LAB
220
HVAC
DW
FR1
E
G
HVAC
E
NL
BREAK ROOM
EM
223
FOR CONTINUATION, REF. DRAWING E-1.1
MOUNT @ 8' A.F.F.
E
G
G
B
R
1
OS
3
ELECTRICAL
B
R EM
E
S
OS
EX1
C1
C1
REF.
S
F2
DD1
DD1
(APPLIES TO THIS DRAWING ONLY)
C
MEN
217
L
K
M2
C
M2
M2
M2
B
A3
B
EM
OS
M2
C1
A3
C
EX1
A5
W
R
B
EX1
C
C
C
CORRIDOR
201
EX2
R
EX2
B
N2
N2
N2
N2
C
N2
C
C
C
EM
B
C1
RA-18
R
B
B
B
C
OS
OS
MTG. STORAGE
207
B
C
C DS
C1
R
S
S
R
ICE
C
B
C
B
C
DW
DS
C
C
C
C
C
CATER
206
STUDY
208
OS
REF.
R
C
C
C
NL
C
STUDY
205
C
C
AR
R
C
C
EX3
C
C
F2
EX1
E
R
DC1
DD1
C1
S
OS
CC
EX1
M1
M1
S
M1
DC4
M1
M1
EX1
S
M1
OS
M1
DC4
EX1
R
R
A3
R
EM
A4
R
A4
EM
R
R
R
RB-35
R
A4
E
FR1
RB-1
MOUNT @ 8' A.F.F.
EM R
EM
S
MOUNT @ 8'
ABOVE DECK F.F.
C
NL
OS
UTILITY
202
R
OS
D
EM LS-27
EX1
M2
C
K
DC1
R
S SDC4
A5
DC1
M2
OS
S
2
S
N2
B
M2
M2
A/V-STACKS
209
B
C1
A3
S
A5
K
O1
E
N2
M2
M2
EM
A4
R
A4
1
M1
E
LS-28
M1
C
OS
MEETING ROOM B
204
E
E
FR1
MEETING ROOM A
203
R
E
OS
M1
EE
STORAGE
203A
F2
RD-26
E
A4
A4
A4
A4
A4
EE
R
A3
M1
M1
M1
M1
M1
M1
M1
OS
EE
M1
EE
CLASSIFIED ASSEMBLY LEGEND
FOR CONTINUATION REFERENCE
DRAWING E-1.1 FIXTURE "CC"
M1
OS
EE
M1
SYMBOL
EE
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
ELECTRICAL LIGHTING SECOND FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-1.2
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
ELECTRICAL
CONSTRUCTION NOTES
#
B
1A
B
1B
WH
1
WH
2
1
COORDINATE WITH CASE WORK DRAWING AND SUPPLIER FOR INSTALLATION IN
CASE WORK. FURNISH ALL LABOR AND MATERIAL FOR A COMPLETE
INSTALLATION. INSTALL RECEPTACLE ADJACENT TO COMMUNICATIONS OUTLET
AS APPLICABLE.
2
VAV CONTROLS TRANSFORMER. ELECTRICAL CONTRACTOR SHALL PROVIDE
CENTRALLY LOCATED 120V TO 24V TRANSFORMERS FOR MULTIPLE UNIT
CONNECTIONS. ELECTRICAL CONTRACTOR SHALL PROVIDE DISCONNECT AT EACH
TRANSFORMER LOCATION. TEMPERATURE CONTROLS CONTRACTOR SHALL
PROVIDE ALL CLASS II LOW VOLTAGE WIRING BETWEEN TRANSFORMER AND
TERMINAL BOX ACTUATORS. ELECTRICAL CONTRACTOR SHALL COORDINATE
ABOVE CEILING LOCATIONS OF TRANSFORMERS WITH TEMPERATURE CONTROLS
CONTRACTOR. PLACE LABEL ON TRANSFORMER TO INDICATE "SERVED BY
CIRCUIT" AND "UNIT NAME SERVED".
3
MOTOR OPERATED ROLLING DOOR - COORDINATE WITH THE OVERHEAD DOOR
MANUFACTURER/INSTALLER AND INCLUDE ALL LABOR AND MATERIAL AS
REQUIRED FOR THE ELECTRICAL INSTALLATION OF THE DOOR OPENERS AND
CONTROLS.
4
RECEPTACLE DEDICATED FOR WALL MOUNTED EMPLOYEE TIME CLOCK. MOUNT
CENTER OF SINGLE GANG BOX AT 48" (MAX.) A.F.F. AND LOCATE NEAR VICINITY OF
TIME CLOCK.
122
5
E.C. SHALL COORDINATE WITH MECHANICAL CONTRACTOR, FURNISH AND INSTALL
ALL CONDUIT AND WIRE TO FACILITATE INTERCONNECTION OF PUMPS WITH
BOILERS.
21
6
COORDINATE RECEPTACLE LOCATION WITH EWC REQUIREMENTS.
7
COPIER/SELF CHECK OUT STATION. COORDINATE WITH ARCHITECTURAL PLANS
FOR EXACT LOCATION.
8
PUBLIC ACCESS CATALOG SYSTEM STATION. E.C. SHALL COORDINATE WITH
ARCHITECTURAL PLANS FOR EXACT COLUMN LOCATIONS. FURNISH AND INSTALL
WIREMOLD 2400D SERIES DUAL CHANNEL RACEWAY (OR APPROVED EQUAL)
ALONG COLUMN TO ACCESSIBLE CEILING SPACE. FURNISH AND INSTALL
RECEPTACLES AND COMMUNICATION DEVICES AS NOTED ON PLANS AND ALL
WIREMOLD DEVICE BOXES AND COMPONENTS TO SUPPORT THE SURFACE
MOUNTING OF POWER AND DATA CABLING TO SUPPORT FULL FUNCTIONALITY OF
THE CATALOG SYSTEM.
9
DEDICATED ELEVATOR SERVICE PANEL WITH LOCKABLE COVER TO SERVE
ASSOCIATED AND AUXILIARY CIRCUITS FOR ELEVATOR SHAFT AND MACHINE
ROOM ONLY. PANEL SHALL HAVE A RED LAMICOID TAG RIVETED TO COVER WITH
THE FOLLOWING WORDING: "DEDICATED FOR ELEVATOR EQUIPMENT AND
SYSTEMS ONLY - NO OTHER LOADS ARE PERMITTED". REFERENCE: ASME
A17.1-2004, SECTION 2.7.2.1. VIOLATION WILL RESULT IN PERMIT REVOCATION.
CP
1
GFI
WP
WR
HP-21
PLUMBING
125
P
1B
1
E4.4
P
1A
GFI
FR1
5
RC-2
4
HP-24,26,28
GFI
E-STOP1
VAV
10
24V POWER FROM
TRANSFORMER
RC-24
EF
1
TOILET
GFI GFI
VAV
7
RC-20
111
RD-12
19
T
WORKROOM
USB
RC-26
RD-12
RC-33
24V POWER FROM
TRANSFORMER
USB
VAV
5
3
E-4.1
2
EF
4
24V POWER FROM
TRANSFORMER
RC-22
RC-11
@ 48" A.F.F.
CUSTODIAL
118
RC-5
GFI
WP
WR
RC-6
WOMEN
6
@ 48" A.F.F.
USB
GP-7
1
GFI
WP
WR
MEN
116
RC-31
CIRCULATION
112
POWER FEED SUPPLIED FROM OU-1. REF. DRAWING E-1.3 FOR LOCATION OF
OUTSIDE UNIT.
12
E.C. SHALL COORDINATE WITH MECHANICAL CONTRACTOR FURNISH AND INSTALL
BACK BOXES, CONDUIT, ETC. TO SUPPORT THERMOSTAT CONTROL OF OU-1 AND
IU-1.
13
SINGLE GFI RECEPTACLE IN NEMA 4 ENCLOSURE TO SERVE SUMP PUMP.
COORDINATE LOCATION WITH MECHANICAL CONTRACTOR AND ELEVATOR
INSTALLER.
14
E.C. SHALL FURNISH AND INSTALL A LIGHT SWITCH IN A NEMA 4 ENCLOSURE FOR
CONTROL OF ELEVATOR PIT LIGHT. COORDINATE LOCATION WITH ELEVATOR
INSTALLER, PIT LADDER AND PIT STOP SWITCH.
15
ELEVATOR PIT LIGHT FURNISHED AND INSTALLED BY E.C. E.C. SHALL COORDINATE
WITH ELEVATOR INSTALLER AND ENSURE FIXTURE IS CLEAR AND NOT AN
OBSTRUCTION TO ANY ELEVATOR TRAVEL.
16
E.C. SHALL FURNISH AND INSTALL A GFI RECEPTACLE IN NEMA 4 ENCLOSURE.
COORDINATE EXACT LOCATION WITH PIT LADDER AND ELEVATOR INSTALLER.
17
POWER FOR AREA OF REFUGE EQUIPMENT. REFERENCE DETAIL 1, DRAWING E-4.2
FOR DETAILS.
18
COORDINATE WITH MECHANICAL CONTRACTOR. FAN CONTROLLED BY DDC.
19
INTERLOCK WITH ZONE LIGHTING CONTROL. FOR CONTINUATION REFERENCE
DRAWING E-1.1.
20
SUBSYSTEM GROUND BAR. REFERENCE DETAIL 2, DRAWING E-4.4.
21
MAIN GROUNDING BAR. REFERENCE DETAIL 2, DRAWING E-4.4.
RD-11
USB
RC-27
11
117
T
T
10
E.C. SHALL FURNISH AND INSTALL ALL FIELD WIRING CONNECTIONS TO THE
ELEVATOR CONTROLLER AS REQUIRED FOR A COMPLETE AND OPERATIONAL
SYSTEM. ALL CONNECTIONS SHALL COMPLY WITH CODE AND THE REQUIREMENTS
OF THE ELEVATOR MANUFACTURER. COORDINATE ALL CONNECTIONS WITH
ELEVATOR EQUIPMENT SUPPLIED BY VENDOR.
GFI
T
GFI
3
E-4.3
GP-6
1
1
USB
7
GP-5
USB
RC-28
19
3
E-4.3
USB
USB
GFI
T
5
E4.3
RC-7
119
RC-10 BRANCH MNGR
115
VAV 24V POWER FROM
8 TRANSFORMER
USB
USB
EF
5
STAFF TOILET
19
GFI
WP
WR
GFI
VAV
6
107
EF
3
GFI
WP
24V POWER FROM
TRANSFORMER
RC-9
RC-13
CHILDREN/JUVENILE
YOUTH PROGRAM
109
F
VAV
11
19
RC-15
3
121
T
RC-14
2
T
RD
3
E-4.1
RC-21
T
RC
RC-12
RC-25
BOOK MOBILE
T
RC-4
3
E4.2
RC-16
F
114
USB
EPO
RC-3
LS-3
123
24V POWER FROM
TRANSFORMER
VAV
9
GFI
CORRIDOR
3
E4.2
FR1
RC-23
GFI
FACP
T
EPO
E-STOP2
HP-25,27,29
GFI
BOILER 24V POWER FROM
MDP
TRANSFORMER
124
3
18
BM OFFICE
LS-5
GFI
WP
WR
EF
2
20
ELECTRICAL
S
STORAGE
HP-18
HP-16
HP-32
S
110
RB-33
M
HVAC
M
RC-1
STAIR
RC-8
GFI
HP-20
(APPLIES TO THIS DRAWING ONLY)
19
GFI
WP
WR
RD-1
RC-30
RC-29
RC-32
USB
USB
3
E-4.3
T
3
E-4.3
VAV
2
EF
6
24V POWER FROM
TRANSFORMER
YOUNG ADULTS
108
VAV
4
24V POWER FROM
TRANSFORMER
BOOK RETURN
102
LS-7
GFI
WP
WR
GFI
WP
WR
RD-2
RD-13
COLLECTIONS
106
16
17
3
E-4.3
15
14
VESTIBULE
101
S
GFI
FR1
J
RD-12
RC-17
3
E-4.1
2
T
RC-19
EE-2
GFI
WP
WR
VAV
1
F
24V POWER FROM
TRANSFORMER
1
E4.1
GFI
WP
WR
RD-9
EE-4
ELEV.
103
13
STAIR
RD-8
USB
RC-18
RD-6
3
E-4.1
8
104
T
EE-10
FR1
8
SP
1
10
ELEV.
FR1
103
24V POWER FROM
TRANSFORMER
A
E1.3
VAV
3
EQUIP.
105
3
E-4.1
FR1
EE
1
E4.1
GFI
S
9
RD-5
RD-4
8
3
E-4.1
11
EE-8
12
OU
1
8
T
EE-7
GFI
WP
WR
EE-9,11
RD-7
8
IU
1
EM
RD-3
T
D
EQUIP.
105
EE-1,3,5
A
E1.3
PARTIAL 1st FLOOR ENLARGED PLAN
SCALE: 1/4" = 1'-0"
RD-10
USB
USB
USB
USB
USB
WP
GFI
WR
USB
USB
CLASSIFIED ASSEMBLY LEGEND
WP
GFI
WR
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
ELECTRICAL POWER FIRST FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-1.3
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
G
ELECTRICAL
CONSTRUCTION NOTES
#
CU
1A
GEN
1
COORDINATE WITH CASE WORK DRAWING AND SUPPLIER FOR INSTALLATION IN
CASE WORK. FURNISH ALL LABOR AND MATERIAL FOR A COMPLETE
INSTALLATION. INSTALL RECEPTACLE ADJACENT TO COMMUNICATIONS OUTLET
AS APPLICABLE.
2
RECEPTACLE DEDICATED FOR WALL MOUNTED EMPLOYEE TIME CLOCK. MOUNT
CENTER OF SINGLE GANG BOX AT 48" (MAX.) A.F.F. AND LOCATE NEAR VICINITY OF
TIME CLOCK.
3
NEMA L5-30R LOCKING SINGLE RECEPTACLE. LOCATE ABOVE RACKS FOR SUPPLY
OF POWER TO OWNER FURNISHED/OWNER INSTALLED RACK UPS. REF. DETAIL 4,
DRAWING E-4.2 FOR DETAILS.
4
NOT USED.
5
COORDINATE WITH MILLWORK. MOUNT AT 42" A.F.F.
6
INTERLOCK WITH ZONE LIGHTING CONTROL. FOR CONTINUATION REFERENCE
DRAWING E-1.2.
7
VAV CONTROLS TRANSFORMER. COORDINATE LOCATION WITH MECHANICAL
CONTRACTOR AND SELECT OPTIMAL LOCATION TO MINIMIZE SECONDARY
CONDUCTOR LENGTH TO UNITS. PLACE LABEL ON TRANSFORMER TO INDICATE
"SERVED BY CIRCUIT" AND "UNIT NAME SERVED".
8
ATS-GP LOCATION. REFERENCE RISER DIAGRAM DETAIL, DRAWING E-3.1.
9
SPRINKLER PRE-ACTION SYSTEM CONTROL PANEL. COORDINATE WITH FIRE
PROTECTION PLANS.
G
XFMR
CU
1B
REF.
HP-2,4,6
GFI
3
E-4.3
MECH/ELEC
222
BREAK ROOM
223
GFI
DW
GFI
GFI
T
VAV
20
GP-17
2A
GP-18
LS-10
MDF
221
LS-11
HP
RB
9
RA-6
VAV
23
STAFF TOILET
219
RB-15
GFI
6
6
RA-21
11
MOTORIZED PROJECTOR SCREEN (O.F.C.I.). E.C. SHALL COORDINATE WITH
OWNER, ARCHITECTURAL PLANS AND MANUFACTURER'S INSTALLATION
INSTRUCTIONS FOR REQUIREMENTS RELATING TO POWER AND CONTROL OF
PROJECTOR SCREEN. FURNISH AND INSTALL CONDUIT, POWER WIRING AND ANY
CONTROL WIRING AND MAKE SINGLE POINT CONNECTION TO ALL DEVICES
REQUIRED. E.C. SHALL ALSO FURNISH ONE DATA DROP FOR THIS LOCATION. E.C.
SHALL PROVIDE A 10' LOOP OF EXTRA DATA CABLING AS OUTLINED IN DETAIL 5,
DRAWING E-4.1.
24V POWER FROM
TRANSFORMER
T
EF
9
EF
8
USB
RA-10
3
E-4.3
GP-13,15
S
LS-30
M
RA
ATS-LS LOCATION. REFERENCE RISER DIAGRAM DETAIL, DRAWING E-3.1.
GP-1
(TYP. OF 4)
LS
10
(OPEN TO BELOW)
T
3
10
GP-2
TECH LAB
220
LS-9
GP-19
22
S
RA-17
LS-8
GP
RA-7
24V POWER FROM FILES
VAV TRANSFORMER
224
24V POWER FROM
TRANSFORMER
EF
11
FAMILY
218
6
GFI
RA-9
RD-12
RA-26
RB-14
4
E-4.1
T
VAV
19
7
F
5
3
E-4.3
EF
10
RA-29
24V POWER FROM
GP-4
TRANSFORMER
VAV
12
RB-11
WOMEN
216
24V POWER FROM
TRANSFORMER
MEN
217
USB
RB-13
GFI
3
E-4.3
RB-16
USB
1
T
USB
MAKER
215
RA-28
4
E-4.1
P
24V POWER FROM
TRANSFORMER
COMPUTER LAB
214
RA-32
RA-15
GFI
S
T
RA-16
RB-2
VAV
14
GFI
RA-33
7
F
GFI
GFI
RA-27
USB
RB-4
VAV
21
RA-35
RESEARCH
24V POWER FROM
TRANSFORMER
213
T
24V POWER FROM
TRANSFORMER
4
E-4.1
RD-12
A/V-STACKS
209
IU
IU
2B
CORRIDOR
24V POWER FROM
225
TRANSFORMER
RA-3
RA-5
VESTIBULE
212
VAV
18
GFI
T
4
E-4.1
3
RA-8
E-4.3
T
DIRECTOR
210
8
VAV
24
GFI
GP-3
M
GP-20
HP-34,36,38
GFI
FR1
BOOK KEEPER
211
S
REF
1
AHU
1
GFI
RH
1
GFI
2
RA-14
GFI
J
RA-22,24
FR1
GFI
4
E-4.2
GP-14,16
GFI
EF
7
RA-4
GFI
WP
WR
GFI
GP-9,11
HVAC
RA-2
HVAC
GFI
HP-7,9,11
ELECTRICAL
RA-1
GP-10,12
GFI
WP
WR
GFI
WP
WR
HP-1,3,5
GFI
WP
WR
OU
2B
OU
2A
(APPLIES TO THIS DRAWING ONLY)
RA-30
USB
4
E-4.1
6
USB
EF
12
RA-31
T
RA-34
USB
GFI
EF
13
T
GFI
W
RA-13
VAV
13
RD-12
D
RA-23,25
VAV
17
RB-12
RB-6
ICE
GFI
RB-8
RB-5
MTG. STORAGE
207
4
E-4.1
USB
3
E-4.3
T
DW
GFI
RB-34 RB-20
EF
14
RB-9
J
REF.
GFI
GFI
RB-21
RB-7
GFI
GFI
RB-18
T
GFI
4
E-4.3
11
T
STUDY
205
P
RB-24
VAV
16
RB-10
T
4
E-4.3
24V POWER FROM
TRANSFORMER
4
E4.3
VAV
15
USB
FR1
RB-23
24V POWER FROM
TRANSFORMER
5
E-4.3
J
UTILITY
202
USB
USB
RB-26
RB-17
GFI
USB
RB-27
CORRIDOR
201
3
E-4.3
RB-22
USB
RB-19
T
GFI
WP
WR
4
E-4.1
RB-31
GFI
RB-32 CATER
206
USB
7
F
S
STUDY
208
T
24V POWER FROM
TRANSFORMER
GFI
RB-30
RB-29
S
P
24V POWER FROM
TRANSFORMER
FR1
STORAGE
203A
RB-28
RB-25
USB
5
E-4.3
MEETING ROOM B
204
MEETING ROOM A
203
USB
USB
USB
CLASSIFIED ASSEMBLY LEGEND
USB
SYMBOL
FR1
1 HR. F-R-R ASSEMBLY
PROJECT
NORTH
REQUIRED WORK
DESCRIPTION
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
FLOOR PLAN
SCALE: 1/8" = 1'-0"
ELECTRICAL POWER SECOND FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-1.4
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
ELECTRICAL
CONSTRUCTION NOTES
BN-DC-10
#
D1
D1
C L1-C14
C
110
STORAGE
125
S
DL
STAIR
HVAC
PLUMBING
TS
TS
FS
D
S
FR1
9
9
D1
CR BN-DC-11
V1
D1
6
S
Z1
F
F
DL
F
5
FR1
BN-DC-04 CR D1
DL
D4
119
CR BN-DC-06
5
E-4.1
D1
D4
D2
D2
5
F
YOUTH PROGRAM
S Z2
5
E4.3
D2
D-2
D
DL
CR
BN-DC-05
D1
J
D
F
D2
3
E-4.3
D4
D2
D4 D4
D2
SYSTEM TYPE SMOKE DETECTOR SHALL BE USED TO INITIATE FIRE SERVICE
ELEVATOR RECALL. INTERLOCK THROUGH THE FIRE ALARM SYSTEM.
13
ELEVATOR CAB POE CAMERA. CAMERA FURNISHED AND INSTALLED BY OWNER.
E.C. SHALL COORDINATE WITH ELEVATOR MANUFACTURER FURNISH AND INSTALL
CAT 6 CABLING IN THE ELEVATOR'S TRAVEL CABLE BUNDLE. PROVIDE 10' OF
SPARE CABLE ABOVE ELEVATOR CAB. ROUTE OPPOSITE END THROUGH CONDUIT
BACK TO CABLE TRAY AND LAND AT PATCH PANEL AT NETWORK RACK. PROVIDE
RJ-45 TERMINATIONS AT BOTH ENDS.
7
RD-11
F
9
Z1
11
5
S
D2
BOOK RETURN
102
5
E-4.1
S
D2
CR D1
F
D
DL
D1
9
3
E-4.3
VESTIBULE
CR D1
FAA
D
D1
FR1
1
E-4.2
DL
COLLECTIONS
106
YOUNG ADULTS
108
DL
D1 CR
D2
8
9
D3
D
5
S
Z1
5
E-4.1
Z1
12
116
9
5
COPIER/SELF CHECK OUT STATION. COORDINATE WITH ARCHITECTURAL PLANS
FOR EXACT LOCATION.
D2
10
3
E-4.3
D2
S
11
MEN
D4
3
E-4.3
5
E-4.1
6
Z3
D4
F
10
COORDINATE WITH CASE WORK DRAWING AND SUPPLIER FOR INSTALLATION IN
CASE WORK. FURNISH ALL LABOR AND MATERIAL FOR A COMPLETE
INSTALLATION. INSTALL COMMUNICATION OUTLET ADJACENT TO RECEPTACLE
OUTLET AS APPLICABLE.
D4
D2
9
D2
S
10
D4
D4
117
DL
D1 CR
9
C
D1
WP
D4
D
L1-C9
D-2
F
CIRCULATION
112
5
WOMEN
3
E-4.3
D4
4
D
107
109
S Z1
5
@ 48" A.F.F.
D2
D1 C DL
C L1-C8
D1 CR
D4
D1
@ 48" A.F.F.
9
POE DOOR ACCESS CONTROL - CONTROLS ARE NOTED BY A "BN*" IDENTIFIER).
E.C. SHALL LABEL AND IDENTIFY EQUIPMENT/CABLING WITH NOTED IDENTIFIER.
E.C. SHALL COORDINATE WITH ARCHITECTURAL DOOR ACCESS SINGLE LINE
DIAGRAMS AND SPECIFICATIONS PRIOR TO INSTALLATION. REFERENCE DETAIL 7,
DRAWING E-4.3 WIRING AND INTERCONNECTION DETAILS.
F
115
D1
CHILDREN/JUVENILE
8
E-4.3
D2 MNGR
BRANCH
D4
5
D4
BN-DC-08 CR
POE PEOPLE COUNTER - REFERENCE DETAIL 5, DRAWING E-4.1 FOR CABLE
INSTALLATION DETAILS.
Z1
D2
3
E-4.1
L1-C10
F
S Z2
5
S
D
9
D4
9
C D1
3
E-4.1
D2
D2
8
E-4.3
5
E-4.1
BN-DC-07
DL
J
CR BN-DC-05
CUSTODIAL D1
118
CR BN-DC-09
S
D4
5
E-4.1
5
D1
8
D2
DL
114
DL
4
WORKROOM
D4
7
WALL MOUNT SPEAKERS SHALL BE MOUNTED AT 12' A.F.F. TYPICALLY. IN AN
EFFORT TO ACHIEVE OPTIMAL SOUND DISPERSION, MOUNTING HEIGHT MAY BE
ADJUSTED BETWEEN 9' MIN TO 13' MAX. TILT ANGLE OF SPEAKERS SHALL BE
ADJUSTED IN FIELD. TYPICALLY THE SPEAKER'S CENTER WOULD BE AIMED
TOWARDS THE FURTHEST LISTENER. CONTRACTOR SHALL COORDINATE EXACT
MOUNTING HEIGHTS AND AIMING DIRECTIONS WITH OWNER PRIOR TO
INSTALLATION.
CR BN-DC-06
BN-DC-07
D
Z2 S
9
F
DL
9
SURFACE OR WALL MOUNT SPEAKER (SPEAKER ZONES ARE NOTED BY A "Z*"
IDENTIFIER). E.C. SHALL LABEL AND IDENTIFY EQUIPMENT/CABLING WITH NOTED
IDENTIFIER. REFERENCE DETAIL 9, DRAWING E-4.3 FOR INSTALLATION DETAILS.
STAFF TOILET
111
C D1
6
D1
9
9
S Z2
DROP-IN CEILING SPEAKER (SPEAKER ZONES ARE NOTED BY A "Z*" IDENTIFIER).
REFERENCE DETAIL 2, DRAWING E-4.3 FOR INSTALLATION DETAILS.
L1-C17
D
D2
9
F
5
F
DL
D2
D2
TOILET
D1
BN-DC-08 CR D1
C L1-C11
4
POE CLOCK LOCATION. REFERENCE DETAIL 2, DRAWING E-4.2.
TELECOMMUNICATIONS BOX SHALL BE MOUNTED AT 7.5' A.F.F.TO CENTER OF BOX.
PRIOR TO INSTALLATION, COORDINATE WITH OWNER FOR EXACT LOCATION AND
MOUNTING HEIGHT. OWNER PROVIDE POE CLOCK SHALL FIT OVER AND COVER
THE DEVICE PLATE.
D
F
C L1-C12
123
D1
D
D1
3
WALL MOUNTED EMPLOYEE TIME CLOCK. REFERENCE DETAIL 2, DRAWING E-4.2.
TELECOMMUNICATIONS BOX SHALL BE MOUNTED AT 48" (MAX.) A.F.F. TO CENTER
OF BOX. COORDINATE WITH OWNER FOR SPACING DISTANCE REQUIREMENT OF
THE TIME CLOCK'S BOX LOCATION FROM THE PHONE'S BOX LOCATION. OWNER
PROVIDED TIME CLOCK AND PHONE MUST BE ABLE TO MOUNT SIDE BY SIDE ONCE
INSTALLED.
D4
DL
CR BN-DC-11
D1
CORRIDOR
S Z1
D
BN-DC-01
BN-DC-12 CR
D1
D C
DL
BN-DC-12 CR
WALL MOUNTED PHONE. REFERENCE DETAIL 2, DRAWING E-4.2.
TELECOMMUNICATIONS BOX SHALL BE MOUNTED AT 48" (MAX.) A.F.F. TO CENTER
OF BOX.
S
121
FACP
D1
5
E4.1
BOOK MOBILE
9
L1-C13
CR
DL
F
D2
124
9
2
3
122
BOILER
D
1
PUBLIC ACCESS CATALOG SYSTEM STATION. E.C. SHALL COORDINATE WITH
ARCHITECTURAL PLANS FOR EXACT COLUMN LOCATIONS. FURNISH AND INSTALL
WIREMOLD 2400D SERIES DUAL CHANNEL RACEWAY (OR APPROVED EQUAL)
ALONG COLUMN TO ACCESSIBLE CEILING SPACE. FURNISH AND INSTALL
RECEPTACLES AND COMMUNICATION DEVICES AS NOTED ON PLANS AND ALL
WIREMOLD DEVICE BOXES AND COMPONENTS TO SUPPORT THE SURFACE
MOUNTING OF POWER AND DATA CABLING TO SUPPORT FULL FUNCTIONALITY OF
THE CATALOG SYSTEM.
L1-C26
2
BM OFFICE
ELECTRICAL
L1-C15
(APPLIES TO THIS DRAWING ONLY)
101
Z1 S
8
F
5
3
E-4.1
D1
W
D4
6
Z3
1
E4.1
7
13
ELEV.
C
103
S
L1-C1
D1
12
C L1-C23
L1-C7
C D1
L1-C9
C
D2
D2
D2
3
E-4.1
1
D4
S
S
BN-DC-03
F
D2
3
E-4.1
12
H
S
1
E4.1
A
E1.3
Z1
D
FR1
DL
5
5
Z1
S
D2
Z1
9
CR D1
BN-DC-02
5
E-4.1
D4
D2
D2
1
1
A
D4
E1.3
PARTIAL 1st FLOOR ENLARGED PLAN
SCALE: 1/4" = 1'-0"
4
D2
D1
D2
C
D2
D1
C
L1-C5
L1-C4 C
D1
CLASSIFIED ASSEMBLY LEGEND
DL
Z3
S
CR
BN-DC-03
D1
EQUIP.
105
FR1
EQUIP.
105
3
E-4.1
F
C
FR1
5
1
CR
L1-C3
ELEV.
D2
L1-C6
C D1
104
103
D2
D2
D1
STAIR
S
1
5
E4.1
5
E-4.1
D1
L1-C2
C D1
WP
SYMBOL
D2
REQUIRED WORK
DESCRIPTION
9
6
7
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
ELECTRICAL SPECIAL SYSTEMS FIRST FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-1.5
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
03/01/2018
G
ELECTRICAL
CONSTRUCTION NOTES
#
1
COORDINATE WITH CASE WORK DRAWING AND SUPPLIER FOR INSTALLATION IN
CASE WORK. FURNISH ALL LABOR AND MATERIAL FOR A COMPLETE
INSTALLATION. INSTALL RECEPTACLE ADJACENT TO COMMUNICATIONS OUTLET
AS APPLICABLE.
2
WALL MOUNTED PHONE. REFERENCE DETAIL 2, DRAWING E-4.2.
TELECOMMUNICATIONS BOX SHALL BE MOUNTED AT 48" (MAX.) A.F.F. TO CENTER
OF BOX.
3
WALL MOUNTED EMPLOYEE TIME CLOCK. REFERENCE DETAIL 2, DRAWING E-4.2.
TELECOMMUNICATIONS BOX SHALL BE MOUNTED AT 48" (MAX.) A.F.F. TO CENTER
OF BOX. COORDINATE WITH OWNER FOR SPACING DISTANCE REQUIREMENT OF
THE TIME CLOCK'S BOX LOCATION FROM THE PHONE'S BOX LOCATION. OWNER
PROVIDED TIME CLOCK AND PHONE MUST BE ABLE TO MOUNT SIDE BY SIDE ONCE
INSTALLED.
4
POE CLOCK LOCATION. REFERENCE DETAIL 2, DRAWING E-4.2.
TELECOMMUNICATIONS BOX SHALL BE MOUNTED AT 7.5' A.F.F.TO CENTER OF BOX.
PRIOR TO INSTALLATION, COORDINATE WITH OWNER FOR EXACT LOCATION AND
MOUNTING HEIGHT. OWNER PROVIDE POE CLOCK SHALL FIT OVER AND COVER
THE DEVICE PLATE.
5
DROP-IN CEILING SPEAKER (SPEAKER ZONES ARE NOTED BY A "Z*" IDENTIFIER).
E.C. SHALL LABEL AND IDENTIFY EQUIPMENT/CABLING WITH NOTED IDENTIFIER.
REFERENCE DETAIL 2, DRAWING E-4.3 FOR INSTALLATION DETAILS.
6
SPEAKER ATTENUATOR - SERVES AS VOLUME CONTROL FOR THE SPEAKERS
LOCATED IN THE SAME ROOM AS THE ATTENUATOR. REFERENCE DETAIL 1,
DRAWING E-4.3 FOR INSTALLATION DETAILS.
7
POE PEOPLE COUNTER - REFERENCE DETAIL 5, DRAWING E-4.1 FOR CABLE
INSTALLATION DETAILS.
3
E-4.3
8
POE DOOR ACCESS CONTROL - E.C. SHALL COORDINATE WITH ARCHITECTURAL
DOOR ACCESS SINGLE LINE DIAGRAMS AND SPECIFICATIONS PRIOR TO
INSTALLATION. REFERENCE DETAIL 7, DRAWING E-4.3 WIRING AND
INTERCONNECTION DETAILS.
8
9
COORDINATE WITH MILLWORK. MOUNT AT 42" A.F.F.
8
4
E-4.2
D1 CR
MECH/ELEC
222
S
DW
D2
D1
FR1
DATA 2
D
AHU
1
S
BREAK ROOM
223
F
BN-DC-25
2
L2-C4
L2-C7
D
CR
5
D2
FILES
224
FAMILY
218
D4
DL
D1
CR BN-DC-23
D4
D2
RD-12 5
E-4.1
RESEARCH
8
DIRECTOR
210
4
E-4.1
7
4
D2
D1 C
D1
4
E-4.1
D2
D2
D2
BN-DC-22 CR CR BN-DC-22
A/V-STACKS
209
D4
S
MEN
217
5
L2-C20
S
D4
F
D2
W
F
D1
C
J
D4 C D1
D BN-DC-19
DL D1
D1
CR
D
DL
CR D1
D1
4
F
6
J
S
MTG. STORAGE
207
S
S
CR
D
REF.
4
E-4.3
F
7
J
D
DW
D2
7
8
Z5
J
J
D2
D2
S
D1 C
L
6
DL
8
BN-DC-16 CR
D2
D1 C
4
4
8
J
D1 CR
DL
S
5
E-4.3
D-2
S
D1
D2
Z5
D2
FR1
4
E4.3
H
D1
S
5
E-4.1
D1
C
5
E-4.1
S
S
D1
Z4
L2-C19
D1
C
L2-C16
5
E-4.3
5
S
FR1
STORAGE
203A
D2
D2
D-2
J
S
Z5
5
E-4.1
D2
10
1
E-4.2
F
J
L2-C17
10
E
5
5
E4.1
J
6
8
E-4.3
F
D
L
F
11
7
5
F
S
D2
4
E-4.3
8
4
E-4.3
F
CR BN-DC-16
J
BN-DC-14
L2-C12
4
STUDY
205
D2
D1
5
S
D
DL
CR D1
UTILITY
202
Z4
L2-C13
D2
S
8
3
E-4.3
C D1
5
D1
D2
D
CORRIDOR
201
C
S
CATER
206
L2-C11
D1
C D1
CR
BN-DC-13
D2
D1
D4
H
DL
D
4
E-4.1
5
E4.1
6
C D1
L2-C14
F
DL
D1
L
J
8
E-4.3
BN-DC-13
CR D1
BN-DC-15
8
D1
BN-DC-18
E-4.3
D1 CR BN-DC-15
S Z5
5
D4
D1
ICE
CR D1
D1
L2-C15 C D1
D1
J
C
D2
3
E-4.3
8
S
8
DL
D
D1 L
4
E-4.1
5
D1
DL
4
8 Z4
S
E-4.3
D
DL
BN-DC-17
F
BN-DC-17
Z4
3
E-4.3
BN-DC-19
STUDY
208
5
4
D1
CR D2
DL
CR
WIRE MESH CABLE TRAY SHALL BE 4" HIGH x 8" WIDE MINIMUM. REFERENCE
DETAILS 3, 4 AND 5, DRAWING E-4.4.
8
D4
D2
14
Z4 S
14
D4
@ 48" A.F.F.
D4
S
7
SPRINKLER PREACTION SYSTEM DELUGE RISER. INTERCONNECT TWO SOLENOID
VALVES, TAMPER AND PRESSURE SWITCHES AS SHOWN ON DRAWING FP-01.
D1
Z4
8
13
WOMEN
216
8
D2
S Z4 C L2-C21
4
E-4.1
5
SPRINKLER PREACTION SYSTEM CONTROL PANEL. REQUIRES TWO INTERFACES
WITH FIRE ALARM PANEL, DEDICATED PULL STATION AND CROSS ZONED SMOKE
DETECTORS IN MDF 221. REFER TO DRAWING FP-01 FOR DETAILS.
CR BN-DC-20
S Z4
5
D4
D4
D2
Z4
D4
12
F
F
L2-C10
D4
1
D1
D1
D2
C
5
8
D
5
E-4.1
D1
DL
3
E-4.3
SYSTEM TYPE SMOKE DETECTOR SHALL BE USED TO INITIATE FIRE SERVICE
ELEVATOR RECALL. INTERLOCK THROUGH THE FIRE ALARM SYSTEM.
S
MAKER
215
5
E-4.1
D4
F
11
L2-C9
D2
D4
5
Z4
D4
@ 48" A.F.F.
D4
COMPUTER LAB
D2
214
F
RD-12
D4
@ 48"
A.F.F.
L2-C22
9
D4
5
D1
C
D4
213
5
E-4.1
S Z4
F
D1
8
FUTURE AUDIO SPEAKER LOCATION. E.C. SHALL FURNISH AND INSTALL ONE
SINGLE GANG BOX CENTERED AT 6' A.F.F. AND A 3/4" CONDUIT WITH PULL STRING
TO ACCESSIBLE CEILING SPACE. SPEAKERS SHALL BE O.F.O.I.
8
CR BN-DC-21
J
5
D4
D2
DL
5
Z4
4
E-4.1
8
E-4.3
D
S
D2
DL
10
F
BN-DC-27
CR
D4
D2
D4
L
CR
CR
F
F
D
3
E-4.3
D1 D
F
STAFF TOILET
219
S
D
F
BN-DC-27
5
Z4
D1
F
S Z4
8
D2
S
D2
12
L2-C6
D1
D1 DL
D1
4
E-4.1
212
D
D
D2
S
8
(OPEN TO BELOW)
D2
5
S Z4
DL
DL
D
BN-DC-23
BOOK KEEPER
211
CR
8
DATA 1
MDF
221
D1 CR
D CR
L D1 VESTIBULE
D4
CORRIDOR
225
3
D1
D1
FR1L2-C3
5
DL
D1 DL
D
F
BN-DC-26
BN-DC-24
D1
L2-C5
BN-DC-21
DL
DL
D1 CR
CR
L2-C2
D1
8
V1 D1
D
PS TS
TS
S Z4
8
D1
L2-C24
F
F
BN-DC-25 CR
D1
D
8
TECH LAB
220
SERVER
S
BN-DC-14
S
SPARE
BN-DC-28
5
E-4.1
Z4
D4
13
ELECTRICAL
3
E-4.3
F
BN-DC-28
5
F
D
HVAC
F
DL
REF.
CR
DL D1
F
D
D1
L2-C1
Z4 S
L2-C23
HVAC
L2-C8
BN-DC-29
G
BN-DC-29
5
8
(APPLIES TO THIS DRAWING ONLY)
D2
5
Z5
S
MEETING ROOM B
204
Z5
MEETING ROOM A
203
L2-C18
D2
D1
CLASSIFIED ASSEMBLY LEGEND
D2
F
F
SYMBOL
REQUIRED WORK
DESCRIPTION
FR1
1 HR. F-R-R ASSEMBLY
FS ALL PENETRATIONS, INSTALL AFD IN
DUCTS/OPENINGS, & INSTALL MEMBRANE
PENETRATIONS (RECESSED ITEMS) PER KBC
SECTION 712
AFD = AUTOMATIC FIRE DAMPER
F-R-R = FIRE-RESISTANT-RATED
F-R-W = FIRE-RATED-WALL
PROJECT
NORTH
FLOOR PLAN
SCALE: 1/8" = 1'-0"
ELECTRICAL SPECIAL SYSTEMS SECOND FLOOR PLAN
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-1.6
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
KEYED NOTES
#
PAD MOUNT
TRANSFORMER
METAL WATER PIPE WITHIN
5' OF ENTRANCE
1 INSTALL GROUNDED (NEUTRAL) CONDUCTOR. REF. RISER DIAGRAM.
9
4 INSTALL A CONCRETE-ENCASED MAIN GROUNDING ELECTRODE IN THE
BUILDING FOUNDATION. LOCATE ELECTRODE IN THE BOTTOM ONE-THIRD
OF THE FOUNDATION WITH AT LEAST 2 INCHES OF CONCRETE COVER
(REF. GROUNDING ELECTRODE FOUNDATION CONNECTION DETAIL, THIS
SHEET). FOR BARE, OR GALVANIZED REBARS THAT ARE MADE
ELECTRICALLY CONTINUOUS, USE REINFORCING BARS NOT SMALLER
THAN THE FOLLOWING BASED ON THE TOTAL LENGTH OF THE
INTERCONNECTED AND PARALLELED REBARS:
2
1
208/120 VOLT 3ɸ, 4W
SERVICE ENTRANCE
EQUIPMENT
9
2
13
7
2
2
8
GROUND
5
2
#6 AWG, 600V COPPER CABLE
WITH GREEN INSULATION
BUILDING FOUNDATION
(NEW CONSTRUCTION)
3
6
GROUND
COMMUNICATIONS
BACKBOARD
2
208/120 VOLT BRANCH
PANELBOARDS
9 BOND TO METAL PIPING SYSTEMS IN THE AREA
10
5
8"
#4 AWG. BARE COPPER MIN.
20' LONG MIN.
dia. x 10' Cu CLAD GRD. RODS SPACED @ 10'-0" APART.
11 INSTALL "SUBSYSTEM GROUNDING BUSBAR(S)" (SGB) AS NOTED ON
PLANS. CONNECT TO THE "MGB" USING A #6 AWG, 600V COPPER CABLE
WITH GREEN INSULATION.
SGB
12 AS REQUIRED. E.C. SHALL COORDINATE WITH OWNER REGARDING OFOI
ANY SURGE PROTECTIVE EQUIPMENT; REFERENCE PRIMARY SURGE
PROTECTION MANUFACTURER'S PRODUCT COLLATERAL FOR GROUNDING
REQUIREMENTS. FURNISH AND INSTALL GROUNDING AS DIRECTED BY
MANUFACTURER.
12
SURGE PROTECTION FOR
EXTERIOR POE EQUIPMENT
FOUNDATION OR
FOOTING IN DIRECT
CONTACT WITH EARTH
13 BOND STRUCTURAL STEEL COLUMN TO THE CONCRETE-ENCASED MAIN
GROUNDING ELECTRODE AT SERVICE ENTRANCE. USE COMPRESSION
CONNECTORS THAT MEET IEEE 837 REQUIREMENTS OR USE EXOTHERMIC
WELDS.
2 GROUNDING SYSTEM DIAGRAM
1
PANEL WITH INTERNAL SURGE PROTECTIVE DEVICE DIRECTLY
CONNECTED TO PANEL BOARD BUSBAR ASSEMBLY, RATINGS PER
SPECIFICATIONS - EXTERNAL ADD ON UNITS WILL NOT BE
ACCEPTABLE.
2
ALL BRANCH CIRCUITRY ASSOCIATED WITH PANEL SHALL HAVE
DEDICATED NEUTRAL CONDUCTOR PER CIRCUIT - DO NOT SHARE
NEUTRALS.
3
PER NEC ARTICLE 110.26(C)(3) EQUIPMENT RATED 800A OR MORE
THAT CONTAINS OVERCURRENT DEVICES, SWITCHING DEVICES, OR
CONTROL DEVICES IS INSTALLED AND THERE IS A PERSONNEL
DOOR(S) INTENDED FOR ENTRANCE TO AND EGRESS FROM THE
WORKING SPACE LESS THAN 25 FT FROM THE NEAREST EDGE OF THE
WORKING SPACE, THE DOOR(S) SHALL OPEN IN THE DIRECTION OF
EGRESS AND BE EQUIPPED WITH LISTED PANIC HARDWARE.
4
PER NEC 240.87 ARC ENERGY REDUCTION SHALL BE ENFORCED FOR
ALL 1200 AMP GEAR OR LARGER.
NONMETALLIC SLEEVE UP THRU
FINISHED FLOOR. LOCATE NEAR
THE VICINITY OF THE "MGB" AND
SERVICE ENTRANCE PANEL.
11
10
(APPLIES TO THIS DRAWING ONLY)
LISTED CONNECTION OF
CONDUCTOR TO REBAR
MIN. 2" CONCRETE
ALL SIDES
COIL MINIMUM 6' OF #4 AWG. BARE COPPER
ABOVE SLAB FOR CONNECTION TO SERVICE
EQUIPMENT BY E.C.
8 INSTALL IRREVERSIBLE COMPRESSION CONNECTOR WITH TAMPERPROOF HARDWARE, OR INSTALL EXOTHERMIC WELD.
2
#
-OR-
7 INSTALL BONDING JUMPER WIRE THAT IS SIZED BASED ON NEC TABLE
250-66 USING THE SERVICE, OR SEPARATELY-DERIVED SYSTEM PHASE
CONDUCTOR SIZE.
NEUTRAL
NONMETALLIC SLEEVE UP THRU
FINISHED FLOOR. LOCATE NEAR
THE VICINITY OF THE "MGB" AND
SERVICE ENTRANCE PANEL.
REBAR 12" Ø MIN.
20' LONG MIN.
FOUNDATION OR
FOOTING IN DIRECT
CONTACT WITH EARTH
03/01/2018
ELECTRICAL
CONSTRUCTION NOTES
COIL MINIMUM 6' OF #4 AWG. BARE
COPPER ABOVE SLAB FOR CONNECTION
TO SERVICE EQUIPMENT BY E.C.
6 INSTALL NEUTRAL CONDUCTOR THAT IS NOT LESS THAN THE PHASE
CONDUCTOR AMPACITY. REF. RISER DIAGRAM.
DATA RACK(S)
4
4 INSTALL AN INSULATED THROAT GROUNDING BUSHING ON EACH
METALLIC FEEDER CONDUIT. BOND TO GROUND BUS USING CONDUCTOR
THAT IS SIZED BASED ON NEC TABLE 250-122 USING THE FEEDER CIRCUIT
OVERCURRENT DEVICE SIZE OR THE SEPARATELY DERIVED SYSTEM
OVERCURRENT DEVICE SIZE.
5 INSTALL A "MAIN GROUNDING BUSBAR" (MGB) FOR SINGLE POINT
GROUNDING. LOCATE AT AN ACCESSIBLE POINT NEAR THE SERVICE
ENTRANCE EQUIPMENT. MAKE CONNECTIONS TO THE GROUND
ELECTRODE CONDUCTOR USING IRREVERSIBLE CONNECTORS, OR
EXOTHERMIC WELDS. MAKE OTHER CONNECTIONS TO THE GROUND BAR
USING TWO-HOLE COMPRESSION SPADE LUGS THAT MEET IEEE 837
REQUIREMENTS. LABEL EACH CONNECTION TO THE GROUND BAR.
MGB
2
3 INSTALL AN INSULATED THROAT GROUNDING BUSHING ON EACH
METALLIC SERVICE ENTRANCE CONDUIT. BOND TO GROUND BUS USING
CONDUCTOR THAT IS SIZED BASED ON NEC TABLE 250-66 USING THE
SERVICE PHASE CONDUCTOR SIZE.
5 BOND HOT AND COLD WATER PIPING SYSTEMS.
TOTAL LENGTH MINIMUM REBAR SIZE
40 FT
1/2" (#4 BAR)
NEUTRAL
A CONCRETE ENCASED ELECTRODE SHALL BE PROVIDED AND SHALL CONSIST OF EITHER 20' OF BARE #4 COPPER WIRE
CONTINUOUS AND EXTENDING 6' OUTSIDE THE CONCRETE, OR AT LEAST 20 FEET OF ½ INCH REINFORCING STEEL INSTALLED WITHIN
OR NEAR THE BOTTOM OF THE FOOTING, OR FOUNDATION. THIS SHALL BE COVERED BY AT LEAST 2" OF CONCRETE WHICH IS IN
DIRECT CONTACT WITH EARTH AND CONNECTED BY AN APPROVED METHOD TO A BARE #4 COPPER WIRE EXTENDING 6' OUTSIDE
THE CONCRETE. THE CUMULATIVE LENGTH OF FOOTING STEEL CAN BE ACHIEVED BY NORMAL METHODS OF STEEL TIE WIRES
JOINING SHORTER LENGTHS. SEE DETAILS BELOW.
2 INSTALL GROUNDING CONNECTIONS TO BUILDING STRUCTURE AND
WATER PIPES AT LOCATIONS THAT ARE VISIBLE AND ACCESSIBLE FOR
INSPECTION, MAINTENANCE, AND TESTING.
3 INSTALL EQUIPMENT GROUNDING CONDUCTOR SIZED BASED ON NEC
TABLE 250-122 USING THE FEEDER OVERCURRENT DEVICE SIZE. REF.
RISER DIAGRAM FOR SIZES.
GAS PIPE AND OTHER METAL PIPING
SYSTEMS IN AND ON THE STRUCTURE
THE GENERAL CONTRACTOR AND/OR INSTALLER OF THE BUILDINGS FOUNDATION SHALL COORDINATE FOR, OR INSTALL THE
FOLLOWING FOUNDATION ELECTRODE SYSTEM.
1 CONDUCTOR SIZES SHOWN ARE MINIMUM AND MAY BE LARGER THAN THE
MINIMUM SIZES REQUIRED BY NEC.
2 INSTALL GROUNDING ELECTRODE CONDUCTOR, SIZED BASED ON NEC
TABLE 250-66. USE # 1/0.
2
ELECTRICAL GROUNDING ELECTRODE SYSTEM: (FOUNDATION REQUIREMENTS)
GENERAL NOTES
MIN. 2" CONCRETE
ALL SIDES
3 GROUNDING ELECTRODE FOUNDATION CONNECTION
NO SCALE
NO SCALE
__-_W-G
FEEDER CODE
1
THE GROUND FAULT PROTECTION OF
SERVICE DISCONNECTS OR MAIN
SWITCHGEAR SHALL BE FACTORY
FIELD TESTED AND A REPORT FOR
APPROVAL SHALL BE SUBMITTED TO
THE AUTHORITY HAVING JURISDICTION
AND TO THE ENGINEER - FOLLOW NEC
230.95. TESTING SHALL BE DEEMED
APPROPRIATE BY THE AUTHORITY
HAVING JURISDICTION.
PANEL
"LS"
(LIFE
SAFETY)
PANEL
"GP"
120/208V
3Ø-4W
150A MCB
TVSS
120/208V
3Ø-4W
150A MCB
TVSS
TVSS = 120 kA
2
1
150-4W-G
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
TVSS = 120 kA
2
150-4W-G
150-4W-G
150-4W-G
*
N
L
50 KW, DIESEL FIRED EMERGENCY
GENERATOR WITH WEATHER-PROOF
ENCLOSURE AND SUB-BASE FUEL
TANK (SEE SPEC.)
3P150
1"C AND
CONTROL
CABLING TO
GENERATOR
100 % RATED OUTPUT
BREAKERS (2) - 3P150A
ATS-LS
AUTOMATIC
TRANSFER
SWITCH
225-4W-G
225-4W-G
225-4W-G
225-4W-G
225-4W-G
PANEL
"HP"
PANEL
"RA"
PANEL
"RB"
PANEL
"RC"
PANEL
"RD"
PANEL
"EE"
120/208V
3Ø-4W
600A MLO
TVSS
120/208V
3Ø-4W
225A MLO
TVSS
120/208V
3Ø-4W
225A MLO
TVSS
120/208V
3Ø-4W
225A MLO
TVSS
120/208V
3Ø-4W
225A MLO
TVSS
120/208V
3Ø-4W
400A MCB
TVSS
E
*
60°C
FEEDER CODE
CONDUIT/WIRE DESCRIPTION
200-3W
2-1/2''C-3#3/0
TEMP
RATING
CONDUIT/WIRE DESCRIPTION
TEMP
RATING
800-4W
(2) SETS EA OF 4''C-4#600MCM
75°C
20-2W-G
1/2''C-3#12
20-3W-G
1/2''C-4#12
200-4W
2-1/2''C-4#3/0
800-3W-G
(2) SETS EA OF 4''C-3#600MCM, #1/0 GND
30-2W-G
1/2''C-3#10
200-3W-G
2-1/2''C-3#3/0, #6 GND
800-4W-G
(2) SETS EA OF 4''C-4#600MCM, #1/0 GND
30-3W-G
1/2''C-4#10
200-4W-G
2-1/2''C-4#3/0, #6 GND
1000-4W
(3) SETS EA OF 3''C-4#400MCM
30-4W-G
1/2''C-4#10, #10 GND
225-3W
2-1/2''C-3#4/0,
1000-3W-G
(3) SETS EA OF 3''C-3#400MCM, #2/0 GND
40-2W-G
1/2''C-2#8, #10 GND
225-4W
2-1/2''C-4#4/0,
1000-4W-G
(3) SETS EA OF 3''C-4#400MCM, #2/0 GND
40-3W-G
3/4''C-3#8, #10 GND
225-3W-G
2-1/2''C-3#4/0, #4 GND
1200-4W
(3) SETS EA OF 4''C-4#600MCM
40-4W-G
3/4''C-4#8, #10 GND
225-4W-G
2-1/2''C-4#4/0, #4 GND
1200-3W-G
(3) SETS EA OF 4''C-3#600MCM, #3/0 GND
50-2W-G
3/4''C-2#6, #10 GND
250-4W
3''C-4#250MCM
1200-4W-G
(3) SETS EA OF 4''C-4#600MCM, #3/0 GND
50-3W-G
3/4''C-3#6, #10 GND
250-3W-G
3''C-3#250MCM, #4 GND
1600-4W
(4) SETS EA OF 4''C-4#600MCM
50-4W-G
1''C-4#6, #10 GND
250-4W-G
3''C-4#250MCM, #4 GND
1600-3W-G
(4) SETS EA OF 4''C-3#600MCM, #4/0 GND
60-2W-G
1''C-2#4, #8 GND
300-3W-G
3''C-3#350MCM, #4 GND
1600-4W-G
(4) SETS EA OF 4''C-4#600MCM, #4/0 GND
60-3W-G
1''C-3#4, #8 GND
300-4W-G
3''C-4#350MCM, #4 GND
2000-4W
(5) SETS EA OF 4''C-4#600MCM
60-4W-G
1''C-4#4, #8 GND
400-3W
4''C-3#600MCM
2000-3W-G
(5) SETS EA OF 4''C-3#600MCM, #250 MCM GND
80-2W-G
1''C-2#3, #8 GND
400-3W-G
4''C-3#600MCM, #3 GND
2000-4W-G
(5) SETS EA OF 4''C-4#600MCM, #250 MCM GND
80-3W-G
1-1/4''C-3#3, #8 GND
400-4W
4''C-4#600MCM
2500-4W
(7) SETS EA OF 4''C-4#500MCM
80-4W-G
1-1/4''C-4#3, #8 GND
400-4W-G
4''C-4#600MCM, #3 GND
2500-3W-G
(7) SETS EA OF 4''C-3#500MCM, #350 MCM GND
100-3W
1-1/2''C-3#1
500-3W-G
(2) SETS EA OF 3''C-3#250MCM, #2 GND
2500-4W-G
(7) SETS EA OF 4''C-4#500MCM, #350 MCM GND
100-4W
1-1/2''C-4#1
500-4W
(2) SETS EA OF 3''C-4#250MCM
3000-4W
(8) SETS EA OF 4''C-4#600MCM
100-3W-G
1-1/2''C-3#1, #6 GND
500-4W-G
(2) SETS EA OF 3''C-4#250MCM, #2 GND
3000-3W-G
(8) SETS EA OF 4''C-3#600MCM, #400 MCM GND
100-4W-G
1-1/2''C-4#1, #6 GND
600-3W-G
(2) SETS EA OF 3-1/2''C-3#350MCM, #1 GND
3000-4W-G
(8) SETS EA OF 4''C-4#600MCM, #400 MCM GND
125-3W-G
1-1/2''C-3#1, #6 GND
600-4W
(2) SETS EA OF 3-1/2''C-4#350MCM
4000-4W
(10) SETS EA OF 4''C-4#600MCM
125-4W-G
1-1/2''C-4#1, #6 GND
600-4W-G
(2) SETS EA OF 3-1/2''C-4#350MCM, #1 GND
4000-3W-G
(10) SETS EA OF 4''C-3#600MCM, #500 MCM GND
150-3W-G
1-1/2''C-3#1/0, #6 GND
700-4W
(2) SETS EA OF 4''C-4#500MCM
4000-4W-G
(10) SETS EA OF 4''C-4#600MCM, #500 MCM GND
150-4W-G
1-1/2"C-4#1/0, #6 GND
700-3W-G
(2) SETS EA OF 4''C-3#500MCM, #1 GND
175-3W-G
2''C-3#2/0, #6 GND
700-4W-G
(2) SETS EA OF 4''C-4#500MCM, #1 GND
175-4W-G
2''C-4#2/0, #6 GND
75°C
75°C
FEEDER CODE
EQUIPMENT PROVISIONS FOR ELECTRICAL CONNECTIONS - TEMPERATURE LIMITIONS SHALL COMPLY WITH NEC ARTICLE 110.14 FOR CIRCUITS RATED 100A OR LESS. WIRE SIZES ARE BASED ON TYPE
"THHN" COPPER CONDUCTORS, WITH NOT MORE THAN THREE CURRENT CARRYING CONDUCTORS IN RACEWAY - DERATE PER TABLE 310.15 AS APPLICABLE.
2
3
4
3P150
120/208V
3Ø-4W
1600A
MCB
ATS-EQ
AUTOMATIC
TRANSFER
SWITCH
1
TVSS
2
TVSS = 160 kA
CONCRETE PAD SEE DETAIL
5, DRAWING UE-4.1.
3/4"C WITH 6 CONDUCTOR
BELDEN CABLE TO REMOTE
ANNUNICATOR.
TEMP
CONDUIT/WIRE DESCRIPTION
RATING
ELECTRICAL FEEDER SCHEDULE (CU)
"MDP"
1
POWER CONNECTIONS FOR CONTROL
POWER & COOLANT HEATER - FURNISH &
INSTALL MANUAL MOTOR SWITCHES TO
SERVE AS LOCAL DISCONNECTS FOR CKTS.
600-4W-G
FEEDER CODE SYMBOL - REFER TO FEEDER DIAGRAM
1
2
TVSS = 120 kA
1
2
TVSS = 120 kA
1
2
TVSS = 120 kA
1
2
TVSS = 120 kA
1
2
TVSS = 120 kA
1400-4W
150-4W-G
1
3/4"C-3 #10
TVSS = 250 kA
GENERATOR BATTERY CHARGER
3/4"C-3 #10
GENERATOR HEATER
1" CONTROL WIRING CONDUIT,
TO XFER SWITCHES.
1 ELECTRICAL RISER DIAGRAM
NO SCALE
NEW POLE SET BY UTILITY. REFERENCE DRAWING
UE-1.1. UTILITY SHALL SUPPLY CONDUIT THE
LENGTH OF THE POLE TO E.C. FURNISHED
CONDUIT STUB UPS. UTILITY SHALL SUPPLY
PRIMARY WIRE FROM OVERHEAD LINES AND
SHALL MAKE SINGLE POINT CONNECTION ON
PRIMARY SIDE OF PAD MOUNT TRANSFORMER.
(HV)
"CT" METERING CABINET AND
METER PROVIDED BY UTILITY AND
MOUNTED BY UTILITY TO
TRANSFORMER CABINET.
(LV)
UTILITY NOTE:
THE CONTRACTOR SHALL BE RESPONSIBLE FOR ALL UTILITY COMPANY FEES AND OR CHARGES,
ASSOCIATED WITH ESTABLISHING ELECTRICAL SERVICE TO THE BUILDING AND OR SITE. THIS SHALL
INCLUDE ALL COSTS AND MATERIAL ASSOCIATED WITH PRIMARY CONDUIT, CABLING, POLES,
METERING EQUIPMENT, TAP CABINETS, TERMINATION CABINETS, TRANSFORMERS, DISTRIBUTION
EQUIPMENT, ETC. CONTRACTOR SHALL COORDINATE ALL MAIN SERVICE REQUIREMENTS AND
LOCATIONS WITH UTILITY COMPANY, PRIOR TO BIDDING. ALL ROUGH-INS (PAD, CONDUIT
GROUNDING, LAYOUT, METERING, ETC. SHALL COMPLY WITH UTILITY COMPANY STANDARDS.
1400-4W
ELECTRICAL RISER DIAGRAM
E.C. SHALL FURNISH AND INSTALL THREE EMPTY
4" CONDUITS W/PULL STRINGS. TWO SHALL BE
PROVIDED FOR PRIMARY ELECTRIC POWER AND
ONE SHALL SERVE AS A SPARE. CAP SPARE
CONDUIT FOR FUTURE USE. EXTEND TO UTILITY
POLE AND TURN UP PER DETAIL 4, DRAWING
UE-4.1
E.C. SHALL FURNISH 4' DEEP
TRENCH FOR BURIAL OF PRIMARY
AND SECONDARY CONDUIT RUNS.
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-3.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
CL
WALL MTD.
EMERG. LIGHT
STRUCTURAL CEILING
STRUCTURAL CEILING
PIPE
PERMITTED
CEILING
CABLE
PIPE
PERMITTED
CEILING
CABLE
SUSPENDED CEILING
PIPE
PERMITTED
PIPE
PERMITTED
EXIT
12" ³
REFER TO ARCHITECTURAL DRAWINGS FOR REFLECTED CEILING PLANS
CL
TYPICAL WIRING DEVICE , SWITCH AND
LIGHTING CONTROL - LABEL THE FACEPLATE
INDICATING PANEL NAME AND CIRCUIT NUMBER
(P/C#). THE CHARACTERS SHALL BE A MINIMUM
OF 3/16" HIGH.
F.A. HORN AND/OR STROBE
SUSPENDED CEILING
LUMINAIRE
PERMITTED
LUMINAIRE
PERMITTED
6 FT OR
LESS
LUMINAIRE
PERMITTED
REF. ELECT. PLANS
FOR LOCATIONS AND
DETAILS.
LUMINAIRE
PERMITTED
03/01/2018
30 IN. MIN.
P/C#
P/C#
TYP. DOOR
& FRAME
MINIMUM
CLEAR
DISTANCE
(SEE CHART)
WALL MTD.
TELEPHONE
TOP OF COUNTER
Condition 2 - Exposed live parts on one side of the working space and
grounded parts on the other side of the working space. Concrete, brick, or tile
walls shall be considered as grounded.
96" MAX.
F.A. PULL
STATION
COUNTERTOP
CONTROLS &
OUTLETS
80" MIN.
90" TO BTM
TEMPERATURE
THERMOSTATS ¹
RECEPTACLE
VOICE/DATA
OUTLETS
LIGHTING
CONTROL
ELECTRICAL WIRING DEVICE
IDENTIFICATION
48" MAX.
WORKING SPACE
DEDICATED ELECTRICAL
SPACE - NO PIPES, DUCTS
EQUIPMENT OR OTHER
SYSTEMS
NOTE:
REFER TO SPECIFICATIONS FOR COLOR
SELECTION OF DEVICES AND COVER PLATES.
LIGHT SWITCH
46" MAX. ²
WORKING SPACE
6.5 FT MIN.
48" MAX.
6.5 FT MIN.
Minimum Clear Distance
Nominal Voltage to
Ground
Condition 1
Condition 2
Condition 3
0-150
(3 ft)
(3 ft)
(3 ft)
151-600
(3 ft)
(3-1/2 ft)
(4 ft)
Note: Where the conditions are as follows:
Condition 1 - Exposed live parts on one side of the working space and no live
or grounded parts on the other side of the working space, or exposed live
parts on both sides of the working space that are effectively guarded by
insulating materials.
NO SCALE (TYPICAL ALL LOCATIONS)
15" MIN.
Condition 3 - Exposed live parts on both sides of the working space.
RECEPTACLE
OUTLETS
FINISHED FLOOR
SIDE VIEW
FRONT VIEW
SIDE VIEW
FRONT VIEW
NOTE:
1. E.C. SHALL COORDINATE WITH M.C. FOR EXACT ORIENTATION OF CONTROLS.
2. DIMENSION IS APPLICABLE FOR A STANDARD COUNTERTOP HEIGHT OF 36" (MAX.) WITH A
WIDTH OF 24" (MAX.) AND NO KNEESPACE. E.C. SHALL COORDINATE WITH APPLICABLE
CODES FOR MOUNTING HEIGHTS OF DEVICES OUTSIDE OF THESE DIMENSIONS.
3. FOR CEILING HEIGHTS < 12'. FOR CEILING HEIGHTS > 12', THEN 24" ABOVE DOOR.
PANEL BOARD CONDUIT ACCESS SPACE
PANEL BOARD WORKING CLEARANCES
PANEL BOARD NEC CLEARANCES
TYPICAL DEVICE MOUNTING HEIGHT DETAIL
NO SCALE
NO SCALE
NOTE:
REFER TO ARCHITECTURAL FLOOR COVERING SPECIFICATION APPLICATION OF ALL ASSOCIATED COMPONENTS SHALL BE
COMPATIBLE WITH FLOOR SYSTEM - CONTRACTOR SHALL
COORDINATE AS REQUIRED. E.C. SHALL COORDINATE FLOOR
BOX LOCATIONS PER ARCHITECT PLANS AND FURNITURE
LAYOUTS.
1-1/4"C W/ PULL STRING FOR
COMMUNICATION TO CABLE
TRAY AS APPLICABLE.
LAMICOID EQUIPMENT LABEL
2"
EQUIPMENT DESIGNATION:
SERVED BY:
CIRCUIT NO:
LOCATION:
LOAD SERVED
VOLTAGE:
W
AF
3"
SHOCK HAZARD
WARNING SIGN
ARC FLASH
WARNING LABEL
WOODEN SURVEYORS STAKE
w/TAG INDICATING UTILITIES
MARKED
1
2" x 3' REBAR.
BURY WITH TOP 6"
BELOW FINISHED
GRADE.
CAP AND SEAL.
EXTEND UP TO AND ATTACH
TO STRUCTURE ABOVE.
WARNING/MARKER TAPE
WITH TRACER RIBBON
SLACK #12 GA. CEILING WIRE
LABEL FLOOR BOX
INTERIOR WITH UNIQUE
NUMBER WITH MATCHING
LABEL ON PULL STRING AT
CABLE TRAY.
CLIP TO CEILING WIRE
EXTEND VIA J-HOOK OR D-RING
TO CABLE TRAY AND LAND RUN
AT PATCH PANELS LOCATED AT
DATA RACKS 1 OR 2 IN ROOM
MDF 221.
CONDUITS, OR DUCTS
WITH PULL STRINGS
LETTERING SIZE = 12 PT.
COMM.
3/4"C FOR
POWER
OUTLETS
FLUSH COVER
NOT SHOWN
LABEL DROP
10' OF CAT 6 DATA CABLE w/RJ45
CONNECTOR COILED WITH COIL
SECURED ABOVE CEILING.
QUANTITY AS SPECIFIED ON
PLANS.
EQUIPMENT
ENCLOSURE
COORDINATE WITH OWNER FOR
REQUIRED COMMUNICATIONS
BRACKET/ACTIVATION PLATE.
2'-0" MAX.
NOTE:
CAST IRON RECESSED FLOORBOX FOR ON GRADE
APPLICATIONS EQUAL TO WIREMOLD #RFB4 CI-1 SERIES, WITH
(2) 120V, 20A DUPLEX RECEPTACLES AND THE REMAINDER
SHALL BE USED FOR VOICE/DATA OUTLETS AS NOTED ON PLAN.
FURNISH ALL NECESSARY DEVICE MOUNTING
BRACKETS/PLATES AND A WIREMOLD #FPCTC/FPBTC TOP
COVER ASSEMBLY, AS NECESSARY FOR A COMPLETE
FUNCTIONAL FLOOR BOX ASSEMBLY - FINISH SHALL BE
SELECTED BY ARCHITECT DURING SHOP DRAWING PROCESS.
EXTEND CONDUIT SYSTEM TO CABLE TRAY SYSTEM AS
REQUIRED FOR CABLING INFRASTRUCTURE AND
INTERCONNECTIONS, UNLESS OTHERWISE NOTED. FIELD
COORDINATE EXACT PLACEMENT WITH ARCHITECT.
-TOPPOWER
CEILING WIRE ATTACHED TO GRID
ELECTRICAL EQUIPMENT LABEL
AND IDENTIFICATION
1-1/4"C W/ PULL STRING
FOR COMMUNICATION TO
CABLE TRAY AS
APPLICABLE.
6 CONDUIT STAKING DETAIL
NO SCALE
NO SCALE
ADJUST FLUSH
TO FLOOR
DATA CONNECTION - LAY-IN
5 CEILING LOCATION
10
8
NO SCALE
5
14
-ELEVATION-
9
S
12
GFI
S
1
SINGLE RECEPTACLE (GFI) IN NEMA 4 ENCLOSURE, TO SERVE SUMP PUMP. COORDINATE LOCATION WITH SUMP PIT, M.C. AND ELEVATOR INSTALLER.
CONNECT TO PANEL "E" - 3 #12 AWG IN CONDUIT.
2
GFI DUPLEX RECEPTACLE IN NEMA 4 ENCLOSURE. COORDINATE LOCATION WITH PIT LADDER AND ELEVATOR INSTALLER. CONNECT TO PANEL "EE" 3#12 AWG IN CONDUIT.
3
PIT LIGHT SWITCH IN NEMA 4 ENCLOSURE - MOUNT @ 42" ABOVE SEAL PLATE. COORDINATE LOCATION WITH PIT LADDER AND ELEVATOR INSTALLER.
CONNECT TO PANEL "E" - 3 #12 AWG IN CONDUIT.
13
4
WALL MOUNT PIT LIGHT - REFERENCE FIXTURE SCHEDULE ON DRAWING E5.1 FOR PRODUCT INFORMATION. FURNISHED AND INSTALLED BY THE
ELECTRICAL CONTRACTOR. COORDINATE LOCATIONS WITH ELEVATOR INSTALLER. CONNECT TO PANEL "E"E - 3#12 AWG IN CONDUIT.
ELEV. MACHINE ROOM PLAN
(SCHEMATIC)
5
SMOKE DETECTORS TO SUPPORT ELEVATOR RECALL. LOCATE IN ELEVATOR MECH. RM AND IN EACH LOBBY AT A MAXIMUM OF 15' FROM DOOR(S).
INTERLOCK THROUGH THE FIRE ALARM SYSTEM.
6
SMOKE DETECTOR TO SUPPORT ELEVATOR RECALL SHALL BE INSTALLED WHEN FIRE ALARM SYSTEM IS INCLUDED IN PROJECT.
7
CONTRACTOR SHALL FURNISH AND INSTALL ALL FIELD WIRING CONNECTIONS TO THE ELEVATOR CONTROLLER AS REQUIRED FOR A COMPLETE
OPERATIONAL SYSTEM. ALL CONNECTIONS SHALL COMPLY WITH CODE AND REQUIREMENTS OF THE ELEVATOR INSTALLER. COORDINATE ALL
CONNECTIONS WITH ELEVATOR EQUIPMENT SUPPLIED BY VENDOR.
H
7
6
NO SCALE
LIGHT FIXTURE
WIRE FROM STRUCTURE TO FIXTURE
BY E.C. FOUR REQUIRED OPPOSITE
CORNERS. SHALL BE DISTINGUISHED
BY COLOR, TAGGING OR PERMANENT
EFFECTIVE MEANS - REFER TO NEC
300.11(A)(2).
NOTE:
REFER TO ARCHITECTURAL FLOOR COVERING SPECIFICATION APPLICATION OF ALL ASSOCIATED COMPONENTS SHALL BE
COMPATIBLE WITH FLOOR SYSTEM - CONTRACTOR SHALL
COORDINATE AS REQUIRED. E.C. SHALL COORDINATE FLOOR
BOX LOCATIONS PER ARCHITECT PLANS AND FURNITURE
LAYOUTS.
WIRE FROM STRUCTURE TO
GRID BY CEILING CONTRACTOR
FOUR REQ.
LIGHT
FIXTURE
SUPPORT
1-1/4"C W/ PULL STRING FOR
COMMUNICATION TO CABLE
TRAY AS APPLICABLE.
14
S
9
FIRE ALARM SYSTEM RECALL INTERFACE AND SHUNT TRIP POWER SOURCE SUPERVISION. FURNISH AND INSTALL ALL FIELD INTERLOCK WIRING
BETWEEN SHUNT TRIP AND INITIATION DEVICES WITHIN SHAFT.
DEDICATED ELEVATOR SERVICE PANEL "EE" WITH LOCKABLE COVER, TO SERVE ASSOCIATED AND AUXILIARY CIRCUITS FOR ELEVATOR SHAFT AND
MACHINE ROOM ONLY.
5
10
11
S
5
CEILING HANGER WIRE,
PER ARCHITECTURAL SPECIFICATIONS
TELEPHONE CONNECTION LOCATED AS REQUIRED AND COORDINATED WITH ELEVATOR INSTALLER. EXTEND REQUIRED PHONE CABLING AND
CONDUIT TO TELEPHONE EQUIPMENT OF BUILDING AND TERMINATE.
LIGHT
T-BAR CEILING GRID
(VERIFY LOAD RATING)
13
LIGHTING FIXTURE WITH WIREGUARD, OR POLYCARBONATE LENS. OPEN UNPROTECTED LAMPS SHALL NOT BE PERMITTED.
ACOUSTICAL TILE
2
1.
2.
THE INFORMATION COMMUNICATED IN THIS DESIGN IS BASED AROUND THE USE OF A 60 H.P. MOTOR SPECIFIED FROM ARCHITECTURAL
PLANS. IT ALSO TAKES INTO CONSIDERATION THAT A MOTOR CONTROLLER WILL BE INSTALLED WITH SYSTEM. E.C. SHALL COORDINATE
WITH ARCHITECTURAL PLANS AND ELEVATOR MANUFACTURER AND ADJUST COMPONENTS AS REQUIRED TO MAKE FULL CONNECTION
TO ANY SYSTEM WHICH DEVIATES FROM THAT STATED ABOVE.
ITEMS ASSOCIATED WITH THE ELEVATOR SYSTEM ARE REPRESENTED SCHEMATICALLY IN REFERENCE TO PLAN VIEW DRAWINGS AND
THIS DETAIL. CONTRACTOR SHALL COORDINATE ALL ROUGH-INS AND CONNECTIONS WITH ELEVATOR SHOP DRAWINGS AND VENDOR
FURNISHED EQUIPMENT. FIELD ADJUST PLACEMENT AS REQUIRED FOR COMPLIANCE WITH ELEVATOR REQUIREMENTS, NEC, LOCAL
AND ALL APPLICABLE CODES.
SHAFT SECTION
(SCHEMATIC)
NO SCALE
-TOP-
-ELEVATION-
1. FIXTURE SHALL BE ATTACHED TO THE CEILING T-GRID RUNNERS WITH HOLD-DOWN CLIPS SUITABLE TO RESIST A HORIZONTAL
FORCE EQUAL TO THE WEIGHT OF THE FIXTURE.
2. ALL RECESSED LIGHT FIXTURES WEIGHING LESS THAN 56 POUNDS INSTALLED IN A HEAVY DUTY GRID SYSTEM ARE PERMITTED TO
BE SUPPORTED DIRECTLY FROM THE GRID RUNNERS AND SHALL HAVE A MINIMUM OF TWO (2) #12 GAUGE (SLACK) WIRES
ATTACHED AT DIAGONALLY OPPOSITE CORNERS OF THE FIXTURE AND ATTACHED TO THE STRUCTURE ABOVE.
4 4-GANG FLUSH FLOOR BOX DETAIL
3. ALL RECESSED LIGHT FIXTURES INSTALLED IN AN INTERMEDIATE DUTY GRID SYSTEM MUST BE INDEPENDENTLY SUPPORTED BY A
MINIMUM OF FOUR (4) #12 GAUGE (TAUNT) WIRES ATTACHED AT EACH CORNER OF THE FIXTURE AND ATTACHED TO THE
STRUCTURE ABOVE.
NO SCALE
4. ALL RECESSED LIGHT FIXTURES WEIGHING MORE THAN 56 POUNDS INSTALLED IN ANY CEILING GRID SYSTEM MUST BE
INDEPENDENTLY SUPPORTED BY A MINIMUM OF FOUR (4) #12 GAUGE (TAUNT) WIRES ATTACHED AT EACH CORNER OF THE
FIXTURE AND ATTACHED TO THE STRUCTURE ABOVE.
5. IN APPLICATIONS WHERE TAUNT FIXTURE SUPPORT WIRES ARE USED, THE WIRES INCLUDING THEIR ATTACHMENT POINTS, MUST
BE CAPABLE OF SUPPORTING FOUR (4) TIMES THE WEIGHT OF THE FIXTURE.
6. REFER TO SEISMIC SPECIFICATIONS FOR ADDITIONAL INFORMATION.
1 ELEVATOR SYSTEM SCHEMATIC DETAIL
NOTE:
STAMPED STEEL RECESSED FLOORBOX FOR ABOVE GRADE
APPLICATIONS EQUAL TO WIREMOLD #RFB4 SERIES WITH (2)
120V, 20A DUPLEX RECEPTACLES AND THE REMAINDER SHALL
BE USED FOR VOICE/DATA OUTLETS AS NOTED ON PLAN.
FURNISH ALL NECESSARY DEVICE MOUNTING
BRACKETS/PLATES AND A WIREMOLD #FPCTC/FPBTC TOP
COVER ASSEMBLY, AS NECESSARY FOR A COMPLETE
FUNCTIONAL FLOOR BOX ASSEMBLY - FINISH SHALL BE
SELECTED BY ARCHITECT DURING SHOP DRAWING PROCESS.
EXTEND CONDUIT SYSTEM TO CABLE TRAY SYSTEM AS
REQUIRED FOR CABLING INFRASTRUCTURE AND
INTERCONNECTIONS,UNLESS OTHERWISE NOTED. FIELD
COORDINATE EXACT PLACEMENT WITH ARCHITECT.
1-1/4"C W/ PULL STRING
FOR COMMUNICATION TO
CABLE TRAY AS
APPLICABLE.
FIXTURE SUPPORT SYSTEM NOTES
NOTE:
3/4"C FOR
POWER
OUTLETS
ADJUST FLUSH
TO FLOOR
6
1
POWER
HEAT DETECTOR TO SUPPORT REMOVAL OF POWER TO ELEVATOR CONTROLLER SHALL BE INSTALLED WHEN SPRINKLER SYSTEM IS INSTALLED.
LOCATE WITHIN 2' OF SPRINKLER HEADS IN SHAFT AND MACHINE ROOM. COORDINATE SETTING WITH SPRINKLER HEAD. TO PROVIDE SOURCE OF
CONTROL TO SHUNT TRIP.
4
S
PROVIDE POSITIVE ATTACHMENT OF FIXTURE TO GRID
(4-LOCATIONS) WITH CAPACITY EQUAL TO WEIGHT OF
FIXTURE ACTING IN ANY DIRECTION.
EQUIPMENT ROOM LIGHTING SWITCH TO BE LOCATED ADJACENT TO LATCH SIDE OF MACHINE ROOM DOOR OR ROOM OCCUPANCY MOTION SENSOR
MOUNTED TO WALL OR CEILING AS SHOWN ON PLANS.
COMM.
FLUSH COVER
NOT SHOWN
ATTACH HANGER WIRES TO FIXTURE HOUSING (THREE
TWISTS MINIMUM) EITHER WITH ANGLE BRACKET AND
SELF-TAPPING SCREWS OR ATTACHING POINTS, IF FIXTURE
HAS INTEGRAL HANGER CLIPS.
12
14
S
ELEVATOR FUSED DISCONNECT SWITCH - NEMA 1, ALL-IN-ONE, 400 AMP DISCONNECT (CAPABLE OF BEING LOCKED IN THE "ON" POSITION) WITH
SHUNT TRIP AND FIRE ALARM SAFETY INTERFACE RELAY. WHEN A SPRINKLER SYSTEM IS INSTALLED; INTERCONNECT FIRE ALARM DEVICES AND
SUPERVISE POWER SOURCE OF SHUNT TRIP BY FIRE ALARM SYSTEM, WHEN AVAILABLE. EXTEND CONNECTIONS TO CONTROLLER AS REQUIRED BY
ELEVATOR INSTALLER AND COORDINATE FUSING WITH NAMEPLATE DATA. EATON, BUSSMANN SERIES QUICK-SPEC POWER MODULE SWITCH, OR
APPROVED EQUAL.
COORDINATE WITH OWNER FOR
REQUIRED COMMUNICATIONS
BRACKET/ACTIVATION PLATE.
LABEL FLOOR BOX
INTERIOR WITH UNIQUE
NUMBER WITH MATCHING
LABEL ON PULL STRING AT
CABLE TRAY.
GALVANIZED SUPPORT WIRES AT ALL FOUR
CORNERS CORNERS OF FIXTURE, SECURED TO
STRUCTURE ABOVE. SHALL BE DISTINGUISHED BY
COLOR, TAGGING OR PERMANENT EFFECTIVE MEANS
- REFER TO NEC 300.11(A)(2).
ILLUSTRATION:
FOR WEIGHT LESS THAN 56
LBS. ONLY. HEAVY DUTY
GRID - SEE NOTES.
PANEL SHALL HAVE A RED LAMICOID TAG RIVETED TO COVER WITH THE FOLLOWING WORDING:
"DEDICATED FOR ELEVATOR EQUIPMENT AND SYSTEMS ONLY - NO OTHER LOADS ARE PERMITTED"
Reference: ASME: A17.1-2004 Section: 2.7.2.1 VIOLATION WILL RESULT IN PERMIT REVOCATION.
S
GFI
EXPOSED TEE GRID
SYSTEM
CEILING PANEL
H
8
3
3 4-GANG FLUSH FLOOR BOX DETAIL
ELEVATOR DETAIL TAGGED NOTES:
11
2
2 LAY-IN FIXTURE SEISMIC SUPPORT DETAIL
NO SCALE
ELECTRICAL DETAILS
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-4.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
120VAC IN
NOTES:
1. DIAGRAM IS FOR REFERENCE ONLY. E.C. SHALL COORDINATE
WITH MANUFACTURER FOR ALL PRODUCT SPECIFIC
REQUIREMENTS AND SPECIFIC INSTALLATION INSTRUCTIONS.
2. LOCAL AND/OR STATE CODES MAY HAVE ADDITIONAL CABLING
REQUIREMENTS. CHECK WITH LOCAL AHJ PRIOR TO PURCHASE
OF EQUIPMENT OR INSTALLATION.
3. EQUIPMENT WILL WORK WITH SIP PROTOCOL. SUPPLY WITH
RATH 2100-VOIP ADAPTER.
CAT 6 CABLING
POE SWITCH
(BY OWNER)
HELP
NEU
BRANCH BREAKER FED FROM
PANEL HP-33. PROVIDE WITH
HANDLE LOCK
1-1/4" EMT W/ PULL STRING TO
CABLE TRAY AND BOND TO GND.
LABEL PULL STRING WITH BOX
NUMBER
5" X5"X2-7/8". BOX
W/ MUD RING AS
REQUIRED
3/4" CONDUIT
WITH #12 WIRE
LABEL INTERIOR OF BOX WITH
UNIQUE BOX NUMBER.
E-STOP 1
3/4" CONDUIT
WITH #12 WIRE
PHONE
1P 120V, 15 AMP BREAKER
WITH SHUNT TRIP.
LOCATE AT PANEL HP-20.
BOILER "B-1A"
ST
SOLID COVER PLATE
SOLID LIGHT: CALLING
BLINKING LIGHT: RECEIVED
CAT 6 CABLING
IP CALL BOX
RATH COMMUNICATIONS MODEL
#2100-958SIPC2 (OR APPROVED EQUAL),
LOCATED ON 2ND FLOOR STAIRWELL
(STAIR 104) LANDING IN "AREA OF
REFUGE"
NOTE:
TYPICAL TO ALL WALL
COMMUNICATIONS
OUTLET ROUGH-IN
UNLESS OTHERWISE
NOTED.
ROUTER
(BY OWNER)
TYPICAL WALL OUTLET.
TECHNOLOGY OUTLET (TYP.)
E-STOP 2
1P 120V, 15 AMP BREAKER
WITH SHUNT TRIP.
LOCATE AT PANEL HP-20.
BOILER "B-1B"
RED, NON-ILLUMINATED PUSH-PULL
EMERGENCY STOP OPERATORS WITH
"EMERGENCY BOILER STOP" LEGEND
PLATES.
ST
EATON #10250T5B62-S110, OR
APPROVED EQUAL.
NO SCALE
CAT 6, 568 PATCH CABLE
NOTE:
1.
1.
2.
3.
4.
5.
Proper primary protection is must on all the port at the MDF.
Insert or remove cards only after the system is switched off.
L1
Connect power cord ground to earth to avoid electrical shock.
Observe anti-static measures.
Install in cool dry place away from sun-light, heat, dust and humidity.
1" EMT TO CABLE TRAY AND BOND
TO GND.
5 SQUARE BOX, STEEL CITY #82181T-1234-1
(OR APPROVED EQUAL) AND ONE 5
SQUARE SINGLE GANG DEVICE RING.
ARNING
L2
DIP
DOP
AOP
03/01/2018
2.
INSTALL RED LED PILOT LIGHTS AT
PANEL FOR INDICATION OF E-STOP
ACTIVATION.
PROVIDE ENGRAVED SIGN NEXT TO
PILOT LIGHT INDICATING "MECH/ELEC
RM 124 E-STOP ACTIVATED".
R
LOCATE AT PANEL HP (NOTE 1 & 2)
R
LOCATE AT PANEL HP (NOTE 1 & 2)
COM 1
90-265VAC, 47-63Hz, 3A
4-PORT FACEPLATE VERIFY
WITH ENGINEER.
AIP
1-10 ZONE REQUIRES 22/2 CABLE
USB
LAN
COM 2
ETHERNET
120 VAC, UPS OUTPUT POWER
WAN
CAT6 JACK. QUANTITY AND TYPE
AS SPECIFIED ON PLANS.
POWER SUPPLY WITH UPS
RATH COMMUNICATIONS MODEL
#RP7700104 (OR APPROVED EQUAL),
LOCATE IN BOOK RETURN 102
DISTRIBUTION MODULE,
LOCATE IN BOOK RETURN 102
3
REMOTE EMERGENCY POWER SHUT-OFF DETAIL
NO SCALE
120 VAC UPS
INPUT POWER
SNAP-IN FACEPLATE BLANKS.
PROVIDE ONE FOR EVERY UNUSED
FACEPLATE. VERIFY WITH ENGINEER.
COMMAND CENTER BASE STATION
RATH COMMUNICATIONS MODEL
#2500-10RCFV (OR APPROVED EQUAL),
LOCATE IN VESTIBULE 101
2 SINGLE GANG TECHNOLOGY OUTLET (TYP.)
1 "AREA OF REFUGE" IP EMERGENCY COMMUNICATION SYSTEM DIAGRAM
NO SCALE
NO SCALE
GENERAL CAMERA NOTES:
WALL
IF CEILING CAVITY IS A AIR HANDLING PLENUM,
ALL EQUIPMENT INSTALLED ABOVE CEILING
SHALL BE SUITABLE FOR THE ENVIRONMENT.
4 GANG BOX WITH DUAL GANG MUD RING
AND BLANK COVER.
CAT 6 CABLE. E.C. SHALL FURNISH AND
INSTALL RJ-45 CONNECTORS AT EACH END
AND ANY/ALL COMPONENTS REQUIRED TO
FACILITATE CONNECTION OF THIS LEG. COIL
EXTRA LENGTH OF CABLE INSIDE OF 5 SQUARE
BOX FOR EASE OF CONNECTION WITH CAMERA
ADDITION.
SLACK #12 GA. CEILING WIRE
EXTEND UP TO AND ATTACH
TO STRUCTURE ABOVE
CLIP TO CEILING WIRE
EXTEND VIA J-HOOK OR D-RING
TO CABLE TRAY AND LAND RUN
AT PATCH PANELS LOCATED AT
DATA RACKS 1 OR 2 IN ROOM
MDF 221
CAMERA LOCATIONS ARE ASSIGNED A GIVEN
"L*" IDENTIFIER. E.C. SHALL LABEL AND IDENTIFY
EQUIPMENT AND SUPPORTED CABLING WITH
NOTED IDENTIFIER.
LABEL DROP
10' OF CAT 6 DATA CABLE w/RJ45
CONNECTOR COILED WITH COIL
SECURED ABOVE CEILING.
QUANTITY AS SPECIFIED ON
PLANS.
2'-0" MAX.
CEILING WIRE ATTACHED TO GRID
POE CAMERAS (OFOI). (CAMERA
SHOWN IS DIAGRAMMATIC).
EXTEND VIA J-HOOK OR D-RING TO CABLE TRAY AND
LAND RUN AT PATCH PANELS LOCATED AT DATA
RACKS 1 OR 2 IN ROOM MDF 221.
POE CAMERAS (OFOI). (CAMERA
SHOWN IS DIAGRAMMATIC).
5
WALL MOUNTED SECURITY CAMERA
WIRING DETAIL (TYP.)
6 CEILING MOUNTED SECURITY CAMERA
WIRING DETAIL (TYP.)
NO SCALE
NOTES:
ALL CABLING TO BE MULTIPLE 4-PAIR CAT 6 UTP CABLE. LENGTH NOT TO
EXCEED 300' FROM PATCH PANEL TO WORK AREA OUTLET.
NO SCALE
ALL CABLING IS TO BE PROPERLY SUPPORTED BY CABLE TRAY, CONDUIT,
D-RING/J-HOOKS, AS INDICATED. ALL CONDUIT DROPS TO OUTLETS SHALL BE
IN CONDUIT AND CONCEALED ABOVE CEILING AND IN WALLS.
WALLBOX OCCUPANCY SENSOR CONTROL FOR RESTROOMS
1.
E.C. SHALL COORDINATE WITH OWNERS TECHNOLOGY DIRECTOR FOR
ARRANGEMENT OF PATCH PANEL, INSTALLED IN RACKS AND POSITION AS
DIRECTED.
TYPICAL OCCUPANCY SENSOR LIGHTING, EXHAUST FAN AND LOUVER DAMPER SYSTEM CONTROL
DIAGRAM
2. RELAY 1 SHALL SUPPLY POWER TO THE LIGHTING LOAD.
3. RELAY 2 SHALL SUPPLY POWER TO THE EXHAUST FAN.
QUAD RECEPTACLE WITH INTEGRAL
SURGE SUPPRESSION. LOCATE
BETWEEN EACH RACK (TYPICAL).
SINGLE POINT
SUPPORT
WIRE BASKET TYPE CABLE
TRAY PER PLAN VIEW
CABLE TRAY PER
PLAN VIEW
SINGLE POINT
SUPPORT
4-PORT FACEPLATE. REF.
DRAWING PLANS FOR DATA
DROP REQUIREMENTS.
UNISTRUT SUPPORT
FOR RECEPTACLES.
12"
MINIMUM
MULTIPLE 4-PAIR CAT 6 COMPLIANT UTP CABLE.
LENGTH NOT TO EXCEED 300' FROM PATCH PANEL
TO WORK AREA OUTLET
4" CONDUITS FROM RACK
POST TO CABLE TRAY.
24
23
22
20
21
19
17
18
e PATCH PANEL
16
15
13
14
11
12
10
9
24
23
22
20
21
19
17
18
16
15
14
13
24
23
22
20
21
19
17
18
16
15
13
14
24
23
22
20
21
19
17
18
16
15
14
13
24
23
22
20
21
19
17
18
16
15
13
24
23
22
20
21
19
17
18
16
15
13
6.
REFERENCE MANUFACTURER'S PRODUCT COLLATERAL FOR SPECIFIC PRODUCT REQUIREMENTS AND
INSTALLATION INSTRUCTIONS.
WHITE
LIGHTING
LOAD
LINE
CABLE STORAGE MANAGEMENT
ENCLOSURES (OFOI)
RACK MOUNTED
PATCH PANELS
CAT 6 VIP2000 COMPLIANT
PATCH CORD.
NEUTRAL
AVERAGE LENGTH 10' PATCH
CORD NOT TO EXCEED 25' IN
LENGTH
24
23
22
20
21
19
17
18
16
15
24
23
22
20
21
19
17
18
16
15
24
23
22
20
21
19
17
18
16
15
DATA RACK (OFCI). E.C. SHALL
COORDINATE WITH OWNER
FOR PROCUREMENT AND
PLACEMENT. REF. SYSTEM
NOTES AND PLAN VIEW.
BLACK
WHITE
BLUE
WORK AREA OUTLET PATCH CABLE NOTE:
PROVIDE PATCH CABLES FOR WORK AREA OUTLETS
FOR 90% OF THE TOTAL NUMBER OF VOICE AND DATA
JACKS. LENGTHS SHALL BE DISTRIBUTED AS
FOLLOWS:
MOTOR
EXHAUST FAN
GREEN
24
23
22
20
21
19
17
18
16
15
14
13
13
14
14
13
13
14
11
12
10
9
7
8
3
2
1
e PATCH PANEL
11
12
10
9
7
8
3
2
1
e PATCH PANEL
11
12
10
9
7
8
e PATCH PANEL
11
12
10
9
7
8
2
1
3
3
2
1
NOTE:
CONTRACTOR SHALL
COORDINATE PLACEMENT OF
PATCH PANELS IN RACK WITH
OWNER.
FRONT OF
RACK
BLACK
BLUE
e PATCH PANEL
14
e PATCH PANEL
14
e PATCH PANEL
11
10
9
7
8
12
12
10
9
7
8
11
11
12
10
9
7
8
PROGRAM TO AUTOMATICALLY TURN OFF THE LIGHTING LOAD AND FAN LOAD 20 MINUTES AFTER ALL
OCCUPANTS HAVE EXITED THE ROOM.
TYPICAL WALL
OUTLET.
e PATCH PANEL
11
12
10
9
7
8
2
1
3
3
1
2
2
1
3
3
2
1
PATCH PANEL (CFCI)
24-PORT 1U RACK MOUNT CAT 6
FEED THROUGH PATCH PANEL.
PANDUIT DP6, OR APPROVED
EQUAL (TYP.). QUANTITY AS
REQUIRED.
5.
NEUTRAL
SNAP-IN FACEPLATE BLANKS.
PROVIDE ONE FOR EVERY
UNUSED FACEPLATE. VERIFY
WITH ENGINEER.
e PATCH PANEL
11
12
10
9
7
8
e PATCH PANEL
7
8
2
1
3
3
2
1
NEMA L5-30R SINGLE RECEPTACLE.
FOR SUPPLY OF POWER TO OWNER
FURNISHED/OWNER INSTALLED
RACK UPS (TYPICAL).
PROGRAM TO AUTOMATICALLY TURN ON BOTH THE LIGHTING LOAD AND FAN LOAD WHEN INITIAL
OCCUPANCY IS DETECTED.
RECEPTACLES
CAT 6 COMPLIANT JACK.
VERIFY WITH ENGINEER.
4" CONDUITS FROM RACK
POST UP TO CABLE TRAY.
MECHANICALLY ATTACH AND
INSTALL BUSHINGS AND
BONDING (TYP., AS REQUIRED).
4.
RESTROOM WALLBOX
SENSOR
10 FOOT PATCH CABLE: 40% OF TOTAL
15 FOOT PATCH CABLE: 40% OF TOTAL
25 FOOT PATCH CABLE: 20% OF TOTAL
7
WALLBOX OCCUPANCY CONTROL DIAGRAM
FOR RESTROOM LIGHTING & EXHAUST
NO SCALE
ELECTRICAL DETAILS
MARCUM
4
TYPICAL 2 AND/OR 4-POST RACK CONFIGURATION DETAIL
NO SCALE
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-4.2
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
NOTE:
ALL EQUIPMENT INSTALLED ABOVE CEILING
SHALL BE SUITABLE FOR THE ENVIRONMENT.
WALL SURFACE.
EXTEND SHIELDED AUDIO CABLE TO
CEILING SPEAKERS AS SHOWN.
PROVIDE CAT6 CABLE WITH 1' OF SLACK
INSIDE ENCLOSURE. TERMINATE END
WITH RJ45 CONNECTOR.
·
·
03/01/2018
3
PROJECTOR INSTALLED
BY OWNER.
OWNER SHALL FURNISH AND INSTALL POE TO USB
CHARGER, IPAD AND USB CABLE TO CHARGER.
FSR
1" EMT WITH PULL STRING TO
ACCESSIBLE CEILING SPACE.
IT-CHRG-P2U
973-785-4347
www.fsrinc.com
4" EMT FOR RECEPTACLE POWER
FROM DESIGNATED PANEL.
PROJECTOR POWER AND WALL
OUTLET SHALL BE ON SAME
CIRCUIT.
PROJECTOR MOUNT FURNISHED BY
OWNER, INSTALLED BY CONTRACTOR.
COORDINATE LOCATIONS WITH
ARCHITECTURAL PLANS.
NOTE: SHORT THROW PROJECTOR
SHALL BE INSTALLED IN "YOUTH
PROGRAM 109".
PROJECTOR MOUNT SUPPORTED
AND ATTACHED TO OVERHEAD
STRUCTURE BY CONTRACTOR.
FOR CABLE RUNS UP TO 30 M, USE 2.5 mm² MINIMUM.
FOR CABLE RUNS GREATER THAN 30 M, USE 4.0 mm² MINIMUM.
ALL AUDIO WIRING AND CONNECTIONS MUST WIRED PER AUDIO
ENGINEERING SOCIETY (AES) STANDARDS.
VOLUME CONTROL DEVICE (OFOI)
E.C. SHALL COORDINATE WITH OWNER
FOR MODEL OF VOLUME CONTROL
SELECTED AND FURNISH AND INSTALL
A SINGLE OR DUAL GANG BOX AS
REQUIRED BY VOLUME CONTROL
DEVICE. MOUNT BACK BOX 48" (MAX.)
A.F.F. TO CENTER OF BOX.
3/4" EMT FOR RECEPTACLE
POWER FROM DESIGNATED PANEL
- PROJECTOR AND WALL OUTLETS
SHALL BE ON SAME CIRCUIT.
CEILING
MOUNT ENCLOSURE IN HORIZONTAL (LANDSCAPE)
ORIENTATION.
WIRING (FURNISHED AND INSTALLED BY E.C.) SHALL BE FINE STRAND, 2
CORE SHIELDED SPEAKER CABLE RATED FOR 70V. MINIMUM GAUGE OF
CABLE SHALL BE AS FOLLOWS:
CONTRACTOR SHALL FURNISH AND INSTALL
1 SINGLE GANG JUNCTION BOX, DUPLEX
RECEPTACLE AND DEVICE PLATE IN ONE OF
THE DEVICE CUT OUTS LOCATED IN THE
PROJECTOR MOUNT.
1" EMT TO CABLE TRAY.
BOND TO GROUND.
IPAD WALL MOUNT ENCLOSURE
E.C. SHALL FURNISH AND INSTALL ONE FSR, INC.
FLUSH MOUNT ENCLOSURE ITEM # 17948, MODEL #
WE-FMIPDairNB-WHT OR ITEM # 17916, MODEL #
WE-FMIPDairNB-BLK (ARCHITECT TO SELECT COLOR).
2'X2' DROP-IN CEILING SPEAKER (OFOI),
E.C. SHALL MAKE CONNECTION TO SEISMIC ATTACHMENT POINTS AND
SUPPORT PER DETAIL 2, DRAWING E-4.1.
3/4" EMT
WITH BUSHING AND
AUDIO CABLES ONLY
1" EMT WITH CAT 6 CABLE TO
CABLE TRAY. BOND TO GND.
5 SQUARE BOX, STEEL CITY #82181T-1234-1
(OR APPROVED EQUAL) AND ONE 5
SQUARE SINGLE GANG DEVICE RING.
REFERENCE PROJECTOR DATA
FACEPLATE DETAIL.
1 1 4" EMT WITH PULL STRING
TO PROJECTOR DATA J-BOX.
POE TO USB CHARGES
POWER OUT: 10W MAX
POE
POE
POWER POWER
IN
OUT
MADE IN USA
PATENT
PENDING
POE
POWER
ON
IN AN EFFORT TO MINIMIZE HUM IN THE SYSTEM, ALL AUDIO CABLES MUST
ROUTED AWAY FROM ANY AC WIRING.
CONTRACTOR SHALL REFERENCE MANUFACTURING INSTRUCTIONS AND
MAKE ALL NECESSARY ADJUSTMENTS TO THE SPECIFICATIONS ABOVE
BASED ON MANUFACTURER'S SPECIFIC REQUIREMENTS.
5 SQUARE BOX, STEEL CITY #82181T-114
(OR APPROVED EQUAL) AND ONE 5
SQUARE SINGLE GANG DEVICE RING.
REFERENCE PROJECTOR DATA
FACEPLATE DETAIL.
MOUNT 54" TO BOTTOM A.F.F.
TYPICAL WALL OUTLETS
1
SOUND/PA SYSTEM WITH VOLUME CONTROL
8
NO SCALE
MEETING ROOM SCHEDULE SIGNAGE MOUNT DETAIL
OVERHEAD PROJECTOR PERSPECTIVE VIEW
5
NO SCALE
FACEPLATE WITH DEVICES
FOR CABLING SYSTEMS.
NO SCALE
FURNISH AND INSTALL CAT6
DATA JACKS
FURNISH AND INSTALL SNAP-IN
FACEPLATE BLANKS. PROVIDE ONE
FOR EVERY UNUSED FACEPLATE.
VERIFY WITH ENGINEER.
NOTE:
ALL EQUIPMENT INSTALLED ABOVE CEILING
SHALL BE SUITABLE FOR THE ENVIRONMENT.
1" EMT TO ACCESSIBLE CEILING SPACE. EXTEND
CAT6 CABLING VIA J-HOOK OR D-RING TO CABLE
TRAY AND LAND RUN AT PATCH PANELS LOCATED
AT DATA RACKS 1 OR 2 IN ROOM MDF 221
AUDIO CABLES (ONLY) SHALL
BE INSTALLED IN CONDUIT OR
CABLE TRAY (TYP.).
1/2" EMT FOR POWER TO RECEPTACLE.
CONDUIT AND WIRING TO ROUTE BACK
TO PANEL.
PROJECTOR DATA FACEPLATE DETAIL
NO SCALE
WALL
MONITOR (OFOI) AND
BRACKET (OFCI).
2'X2' DROP-IN CEILING AND ALL-ENVIRONMENT WALL MOUNT SPEAKERS (OFOI),
E.C. SHALL MAKE CONNECTION TO DROP-IN CEILING SPEAKER SEISMIC
ATTACHMENT POINTS AND SUPPORT PER DETAIL 2, DRAWING E-4.1.
EXTEND AS REQUIRED TO CABLE TRAY. BOND
TO SIGNAL GROUND. CABLE TO EXTEND TO
HEAD-END EQUIPMENT (OFOI) AND CONNECTED
AS DEDICATED PAGING ZONES. REF. DRAWINGS
E-1.5 AND E-1.6 FOR CONNECTION AND ZONING
DETAILS.
SINGLE GANG BOX RECESSED IN WALL WITH
BLANK COVER PLATE FOR FUTURE PROVISION
OF AUDIO SPEAKERS. (TYP. OF 2)
REFERENCE CABLING NOTES FROM
DETAIL 2 THIS SHEET FOR DETAILS.
WIRING (FURNISHED AND INSTALLED BY E.C.) SHALL BE FINE STRAND, 2 CORE
SHIELDED SPEAKER CABLE RATED FOR 70V. MINIMUM GAUGE OF CABLE SHALL
BE AS FOLLOWS:
·
·
WALL MTD AUDIO
SPEAKERS (OFOI).
FOR CABLE RUNS UP TO 30 M, USE 2.5 mm² MINIMUM.
FOR CABLE RUNS GREATER THAN 30 M, USE 4.0 mm² MINIMUM.
MONITOR (OFOI) AND
BRACKET (OFCI).
ALL AUDIO WIRING AND CONNECTIONS MUST WIRED PER AUDIO ENGINEERING
SOCIETY (AES) STANDARDS.
IN AN EFFORT TO MINIMIZE HUM IN THE SYSTEM, ALL AUDIO CABLES MUST
ROUTED AWAY FROM ANY AC WIRING. ALL WIRING MUST COMPLY WITH NFPA
70.
DUPLEX RECEPTACLE.
REFERENCE DETAIL 6, THIS SHEET FOR DETAILS.
COORDINATE MOUNTING HEIGHT OF MONITOR WITH
OWNER PRIOR TO INSTALLATION. POWER AND DATA
PLUGS TYPICALLY FEED TO BOTTOM OF MONITOR SO BOX
SHOULD BE MOUNTED BELOW THE MONITOR MOUNTING
BRACKET. BOX HOWEVER MUST BE KEPT HIDDEN BEHIND
OUTLINE OF THE MONITOR INSTALLED.
CONTRACTOR SHALL REFERENCE MANUFACTURING INSTRUCTIONS AND MAKE
ALL NECESSARY ADJUSTMENTS TO THE SPECIFICATIONS ABOVE BASED ON
MANUFACTURER'S SPECIFIC REQUIREMENTS.
9
2
6'
GENERAL PA SYSTEM DETAIL
NO SCALE
WALL MOUNTED "AUDIO" SPEAKER
DETAIL (TYP.)
NO SCALE
1" EMT TO ACCESSIBLE CEILING SPACE. EXTEND
CAT6 CABLING VIA J-HOOK OR D-RING TO CABLE
TRAY AND LAND RUN AT PATCH PANELS LOCATED
AT DATA RACKS 1 OR 2 IN ROOM MDF 221
1/2" EMT FOR POWER TO RECEPTACLE.
CONDUIT AND WIRING TO ROUTE BACK
TO PANEL.
DOUBLE GANG BOX FOR SUPPORT OF O.F.O.I.
DOOR ACCESS CONTROLLER. LOCATE NEAR
DOOR IN ACCESSIBLE CEILING SPACE.
LOCATED AT ALL DOORS. DOOR ACCESS
CONTROLLER SHALL BE OFOI. E.C. SHALL
FURNISH AND INSTALL DOUBLE GANG BOX
WITH COVER PLATE.
18/4 CABLE (CFCI) FOR
ELECTRIC STRIKE (OFOI).
3
FINISHED FLOOR.
4"
EMT WITH PULL STRING TO
ACCESSIBLE CEILING SPACE.
FINISHED FLOOR.
22/8 CABLE (CFCI) FOR
CARD READER.
22/8 CABLE (CFCI) FOR REQUEST
TO EXIT SENSOR.
MONITOR (OFOI) AND
BRACKET (OFCI).
CEILING
CENTER IN LINE WITH CENTER
OF MOUNTING RACK. (TYP. OF 2)
REQUEST TO EXIT SENSOR (O.F.O.I.) LOCATION.
LOCATE ONLY AT DOORS WITH SINGLE CARD
READER. E.C. SHALL FURNISH AND INSTALL
SINGLE GANG BOX WITH COVER PLATE. BOX
SHALL BE MOUNTED HORIZONTALLY.
22/2 CABLE (CFCI) FOR
DOOR SENSOR (OFOI).
REF. DETAIL 9 THIS
SHEET FOR DETAILS.
3
MONITOR (OFOI) AND
BRACKET (OFCI).
CEILING
INFORMATION MONITOR DETAIL
NO SCALE
DUPLEX RECEPTACLE.
EXIT
ENTRANCE
NOTES:
1.
REFERENCE DETAIL 6, THIS SHEET FOR DETAILS.
COORDINATE MOUNTING HEIGHT OF MONITOR WITH
OWNER PRIOR TO INSTALLATION. POWER AND DATA
PLUGS TYPICALLY FEED TO BOTTOM OF MONITOR SO BOX
SHOULD BE MOUNTED BELOW THE MONITOR MOUNTING
BRACKET. BOX HOWEVER MUST BE KEPT HIDDEN BEHIND
OUTLINE OF THE MONITOR INSTALLED.
6'
1" EMT WITH PULL STRING.
1
1
1
4"
CARD READER (OFOI).
REFERENCE PLANS FOR
LOCATION OF SINGLE OR
DOUBLE CARD READER
LOCATIONS.
5 SQUARE BOX, STEEL CITY #82181T-114
(OR APPROVED EQUAL) AND ONE DUAL
GANG MUD RING WITH BLANK COVER
PLATE.
2"
QUADRUPLEX RECEPTACLE
WITH USB POWER.
3.
CAT6 JACK. QUANTITY AND TYPE
AS SPECIFIED ON PLANS.
EMT FOR RECEPTACLE POWER FROM
DESIGNATED PANEL. MONITOR POWER
AND WALL OUTLET SHALL BE ON SAME
CIRCUIT.
EMT WITH PULL STRING.
2.
5 SQUARE BOX, STEEL CITY #82181T-114
(OR APPROVED EQUAL) AND ONE 5
SQUARE SINGLE GANG DEVICE RING AND
DEVICE PLATE AS SHOWN IN DETAIL.
FINISHED FLOOR
TYPICAL WALL OUTLETS
COORDINATE WITH ARCHITECTURAL PLANS
AND SPECIFICATIONS FOR ADDITIONAL
INFORMATION AND REQUIREMENTS.
LOW VOLTAGE CABLING SHALL EXTEND AND
BE ROUTED ABOVE THE LAY-IN CEILING USING
"J" HOOKS.
THIS DETAIL IS DIAGRAMMATIC ONLY. ACTUAL
INSTALLATION REQUIREMENTS MAY DIFFER.
E.C. SHALL REVIEW ALL CONTRACT
DOCUMENTS PRIOR TO BIDDING AND INCLUDE
IN THE BID ALL LABOR AND MATERIAL AS
REQUIRED TO INSTALL AND INTER-CONNECT
DEVICES FURNISHED BY THE HARDWARE
VENDER AS IT RELATES TO ELECTRICAL
POWER AND CONTROLS OF INDICATED DOORS.
FINISHED FLOOR
7
POE DOOR ENTRY CONTROL DEVICE MOUNTING DETAIL
NO SCALE
FINISHED FLOOR.
FINISHED FLOOR.
NOTES:
1. ALL DATA JACKS SHALL BE COMMSCOPE
#MGS400BH-318 BLUE (OR APPROVED
EQUAL).
SNAP-IN FACEPLATE BLANKS.
PROVIDE ONE FOR EVERY
UNUSED FACEPLATE. VERIFY
WITH ENGINEER.
ELECTRICAL DETAILS
4
INFORMATION MONITOR DETAIL
NO SCALE
6
BOX DETAIL
NO SCALE
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-4.3
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
CABLING:
CONDUIT:
PULL BOX INSTALLATION:
ALL CABLING SHALL BE MULTIPLE 4-PAIR CAT 6
COMPLIANT UTP CABLE. LENGTH NOT TO
EXCEED 300' FROM PATCH PANEL TO WORK
AREA OUTLET.
·
ALL CABLING SHALL BE PROPERLY
SUPPORTED BY CONDUIT, D-RING OR J-HOOKS,
AS REQUIRED.
·
LOCATE PULL BOXES IN EASILY ACCESSIBLE
LOCATIONS. SHOULD BE USED WHEN
INSTALLING A PULL STRING OR CABLE, FISHING
THE CONDUIT'S RUN AND PULLING AND
LOOPING THE CABLE IN THE NEXT LENGTH OF
CONDUIT.
·
ALL DROPS TO OUTLETS SHALL BE IN CONDUIT
AND CONCEALED ABOVE CEILING AND/OR IN
WALLS (IF APPLICABLE).
·
E.C. SHALL COORDINATE WITH OWNERS
TECHNOLOGY DIRECTOR FOR ARRANGEMENT
OF RACK PATCH PANELS AND POSITION
EQUIPMENT AS DIRECTED.
·
CABLING COLOR SCHEMES:
SECTIONS BETWEEN PULL POINTS SHALL
NOT EXCEED 100'. IN RUNS THAT TOTAL
MORE THAN 100', INSERT PULL BOXES SO
THAT NO SEGMENT BETWEEN PULL
POINTS EXCEEDS THE 100' LIMIT.
NO SECTION SHALL CONTAIN MORE THAN
TWO 90° BENDS.
FOR CONDUITS WITH AN INTERNAL
DIAMETER OF 2" OR LESS - INSIDE BEND
RADIUS OF A BEND IN CONDUIT SHALL BE
AT LEAST SIX TIMES THE INTERNAL
DIAMETER.
FOR CONDUITS WITH AN INTERNAL
DIAMETER GREATER THAN 2" - INSIDE
BEND RADIUS OF A BEND IN CONDUIT
SHALL BE AT LEAST TEN TIMES THE
INTERNAL DIAMETER.
SHALL BE BONDED TO GROUND IN
ACCORDANCE WITH NATIONAL, OR LOCAL
CODE REQUIREMENTS.
2
SGB
"SGB" STANDS FOR SUBSYSTEM GROUNDING
BUSBAR. LABEL BUSBAR ACCORDINGLY.
PULL BOXES SHALL BE USED WHEN:
·
·
·
4
CONDUIT RUNS ARE MORE THAN 100'.
CONDUCT SECTIONS CONTAIN MORE THAN
TWO 90° BENDS.
PULL BOXES SHALL NOT BE USED FOR
SPLICING CABLE.
3
MGB
COORDINATE ALL COLOR SCHEMES WITH
TECHNOLOGY DIRECTOR.
1
"MGB" STANDS FOR MAIN GROUNDING
BUSBAR. LABEL BUSBAR ACCORDINGLY.
SCHEMATIC LAYOUT OF EQUIPMENT IS
DIAGRAMMATIC, SLIGHT REPOSITIONING OF
EQUIPMENT IS PERMITTED AT BACKBOARD.
#
4' x 8' x 3/4" THK. (MIN.) PLYWOOD BACKBOARD.
E.C. SHALL COORDINATE WITH A.H.J. AND INSURE
BACKBOARD AND ANY/ALL COMPONENT MATERIALS
MEET ALL APPLICABLE CODE REQUIREMENTS.
03/01/2018
FIBER OSP FROM UTILITY
COMPANY TO FIBER PATCH
PANEL LOCATED IN MDF 221
1.
MGB = COPPER GROUND BAR,
APPROVED EQUAL.
1
2.
SGB = COPPER GROUND BAR,
OR APPROVED EQUAL.
1
4"
x 4" x 24". HARGER GBI14424TMGBKT, OR
4"
x 4" x 12". TO HARGER GBI14412TMGBKT,
3. INSULATORS
4. WALL MOUNT BRACKET.
CAT 6, 110-STYLE CROSS
CONNECT CONNECTOR BLOCK
(AS APPLICABLE TO SYSTEM
BY UTILITY).
5. APPLY AN ANTI OXIDANT (PENETROX) TO ALL CONNECTION SURFACES.
2 GROUND BAR DETAILS
TVSS PROTECTION
MODULE
NO SCALE
SUBSYSTEM GROUNDING BUSBAR,
REFERENCE DETAIL 2, THIS PAGE.
ELEVATOR REQUIRES ONE PHONE LINE
EACH WITH ONE 4 PAIR CAT 5E CABLE IN A
HOME RUN CONDUIT FROM THE "MDF" TO
THE ELEVATOR CONTROL PANEL
TERMINATED TO ONE RJ31X JACK IN THE
PANEL.
6" (MIN.)
A.F.F.
GROUND WIRE TO MGB. REF. DETAIL 2,
DRAWING E-3.1. INSTALL IN 12" CONDUIT.
COPPER OSP FROM UTILITY
COMPANY (IF REQUIRED).
FIRE ALARM REQUIRES TWO PHONE LINES
WITH TWO 4 PAIR CAT 6 CABLES N A HOME
RUN CONDUIT FROM THE "MDF" TO THE
FIRE ALARM PANEL TERMINATED TO TWO
RJ31X JACKS IN PANEL.
QUAD OUTLETS WITH INTEGRAL
SURGE SUPPRESSION.
ONE 4" UTILITY CONDUIT WITH PULL STRING
FOR COMMUNICATIONS.
TWO 4" SPARE CONDUIT W/PULL STRING. ROUTE TO SITE UTILITY
POLE ALONG WITH COMMUNICATIONS CONDUIT. CAP AND STAKE
FOR FUTURE USE.
DEMARCATION BACKBOARD
TRAY SIGNAL GROUND
#6 BARE COPPER
EXTEND FULL LENGTH
EMT CONTAINING
CABLE FROM TRAY
1 COMMUNICATIONS BACKBOARD OVERALL DIAGRAM
GROUNDING BUSHING
TRAY SHALL NOT
SUPPORT CONDUIT
NO SCALE
U.L. APPROVE
COMPRESSION
CONNECTION
ADMINISTRATIVE VOICE AND DATA SYSTEMS GENERAL
REQUIREMENTS:
SCOPE OF WORK SHALL INCLUDE, BUT NOT NECESSARILY BE LIMITED TO, FURNISHING AND INSTALLING A VOICE
AND DATA CABLING SYSTEMS WIRING AS SPECIFIED, DESCRIBED HEREIN AND ON THE PLANS. ALL DATA AND VOICE
CABLING SYSTEM COMPONENTS SHALL BE U.L. LISTED AND CERTIFIED AS CATEGORY 6 COMPLIANT CABLE. ALL
CABLING PRACTICES SHALL CONFORM TO THE REQUIREMENTS OF TIA/EIA BUILDING WIRING STANDARDS, THE IEEE,
THE SPECIFICATIONS AND THE NATIONAL ELECTRICAL CODE. ANY COMPONENT NOT SPECIFICALLY MENTIONED
HEREIN, THAT IS REQUIRED TO PROVIDE A COMPLETE AND FUNCTIONAL SYSTEM, SHALL BE INCLUDED.
BOND EACH SECTION
OF TRAY WITH U.L.
APPROVE CONNECTION
DATA AND VOICE CABLING (ALL OVER IP):
CAT 6 DATA/VOICE CABLES SHALL BE TERMINATED AT PATCH PANELS LOCATED IN THE RACKS. DEVICES SHALL USE
THE 568A WIRING SCHEME. THE QUANTITY AND SIZE OF THE PATCH PANEL(S) SHALL BE DETERMINED BY THE
NUMBER OF OUTLETS TO BE CONNECTED. THE PATCH PANEL SHALL NOT EXCEED 24 PORTS AND BE POSITIONED
WITH IN THE CABINETS PER THE OWNERS DIRECTIVE. THE SYSTEMS SHALL BE TESTED WITH THE OWNER'S
SUPERVISION AND APPROVAL.
LABELS:
GENERAL:
CABLES EXTENDING FROM THE EQUIPMENT LOCATED ON THE RACKS TO THE VARIOUS OUTLETS, SHALL BE
ROUTED THROUGH THE FACILITY AND BE SUPPORTED BY D-RINGS, J-HOOKS AND/OR CONDUIT WHEN INSTALLED
ABOVE THE CEILING. CONDUIT SHALL BE INSTALLED (1" MINIMUM) WITHIN WALLS AND WHEN EXPOSED. CABLE SHALL
BE SUPPORTED IN COMPLIANCE WITH THE NATIONAL ELECTRICAL CODE AND ANY OTHER APPLICABLE CODES.
FACEPLATES AND JACKS SHALL BE COLOR MATCHED TO THE THE REQUIREMENTS LISTED IN THE PLANS OR
SPECIFICATIONS. ALL PATCH PANELS AND PATCH CABLES SHALL BE INCLUDED IN THIS PROJECT. THE INSTALLED
LINK, INCLUDING PATCH CABLES, SHALL BE TESTED PER THE SPECIFICATIONS. A PRINTOUT OF THESE TEST
RESULTS, AS WELL AS A REPRODUCIBLE DRAWING OF THE WORK PERFORMED SHOWING DEVICE LOCATION AND
WIRE NUMBERING SCHEME, SHALL BE FURNISHED AT THE COMPLETION OF THE PROJECT. THIS DRAWING SHALL BE
PROVIDED IN BOTH PRINTED AND ELECTRONIC FORMAT. THE ELECTRONIC FORMAT SHALL BE EITHER AUTOCAD
.DXF OR .DWG.
BASKET TYPE CABLE TRAY
EACH DATA AND VOICE OUTLET SHALL BE LABELED AT THE FACEPLATE. THE LABEL SHALL CONSIST OF ONE ROW OF
FOUR CHARACTERS AND ONE ROW OF TWO CHARACTERS. THE CHARACTERS FOR THE FIRST ROW ARE AS
FOLLOWS: DIGIT ONE IS NUMERIC AND INDICATES THE WIRING CLOSET NUMBER. DIGIT TWO IS ALPHA AND
INDICATES THE FUNCTION OF THE JACK ('D' FOR DATA, 'V' FOR VOICE). DIGITS THREE AND FOUR ARE NUMERIC AND
INDICATE THE PATCH PANEL NUMBER. THE TWO DIGITS ON THE SECOND ROW ARE NUMERIC AND INDICATE THE
PORT NUMBER ON THE PATCH PANEL OR 110 BLOCK. THERE SHALL BE A LABEL ATTACHED TO THE TOP LEFT HAND
CORNER OF EACH PATCH PANEL DEPICTING THE WIRING CLOSET NUMBER, FUNCTION OF THE PATCH PANEL AND
PATCH PANEL NUMBER. THE CHARACTERS SHALL BE A MINIMUM OF 3/16" HIGH.
GROUNDING BUSHING
ROUTE UNDER TRAY
WHEN CROSSING
TRAY SHALL NOT
SUPPORT CONDUIT
NOTE:
SIGNAL REFERENCE GROUND
SHALL EXTEND FULL LENGTH
OF TRAY AND BOND ALL RACKS
AND TELEPHONE BOARDS
THE RACEWAY SYSTEM SHALL BE GROUNDED IN COMPLIANCE WITH ALL APPLICABLE CODES.
5
CABLE TRAY BONDING DETAIL
NO SCALE
OPTIONAL CENTER SUPPORT METHOD - 1/2"
THREADED ROD HANGER SECURED FROM
STRUCTURE. PROVIDE ROD SUPPORTS
EVERY 8 FT. OR AS RECOMMENDED BY THE
TRAY MANUFACTURER.
ALL TURNS IN CONDUIT SHALL
BE 90 DEGREE WIDE SWEEP.
TURN OUT INTO ACCESSIBLE
CEILING SPACE AND INSTALL
BUSHING.
MINIMUM 4" x 8" WIRE
MESH CABLE TRAY
WIRE MESH CABLE TRAY, TRAY
WIDTH AS INDICATED ON PLAN
VIEW, TRAY DEPTH SHALL BE 4"
MAINTAIN 12" OF VERTICAL
CLEARANCE ABOVE CABLE
TRAY.
TERMINATE CONDUITS A MINIMUM
OF 4" TO 6" FROM CABLE TRAY.
CABLE TRAY HEIGHT 3"
MINIMUM TO 12" MAXIMUM
ABOVE CEILING WHERE NO
OBSTACLES ARE PRESENT.
BACKBOX, FACE PLATE AND
JACKS (AS NOTED ON PLANS)
@ 44" TO BTM A.F.F. FURNISHED
AND INSTALLED BY E.C.
3/4"C
12" MIN.
3/4"C OR
AS NOTED
MAINTAIN 12" OF SPACE BETWEEN
SOURCES OF ELECTRO MAGNETIC
INTERFERENCE SUCH AS LIGHTING
FIXTURES.
8
1
12" MIN.
BACKBOX, FACE PLATE AND
JACKS (AS NOTED ON PLANS)
@ 16" TO BTM A.F.F. FURNISHED
AND INSTALLED BY E.C.
12"
HVAC DUCT
1"C
CEILING HEIGHT
K
1
8
1
8
1
LIGHT
MAINTAIN A MINIMUM
CLEARANCE OF 6" FOR SIDE
ACCESS TO CABLE TRAY.
RECESSED FLOOR LOCATION, AS APPLICABLE
SHALL BE COORDINATED WITH G.C., ARCHITECT
AND FURNITURE VENDER.
COMMON CORRIDOR
ELECTRICAL DETAILS
3
STANDARD COMMUNICATIONS
RACEWAYS TO CABLE TRAY
NO SCALE
4 MINIMUM CABLE TRAY CLEARANCES
NO SCALE
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-4.4
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
MECHANICAL EQUIPMENT CONNECTION SCHEDULE
LIGHTING FIXTURE SCHEDULE
TYPE
A1
MANUFACTURER
PEERLESS
LIGHTING
OR EQUAL
A2
PEERLESS
LIGHTING
OR EQUAL
A3
PEERLESS
LIGHTING
OR EQUAL
A4
PEERLESS
LIGHTING
OR EQUAL
A5
PEERLESS
LIGHTING
OR EQUAL
CATALOG NO.
VMM9 LSL 20 MSL4 80CRI 40K ID1100LMF
20/80 DARK ZT 120 SCT F1/MCS 24A ___
RDEP
LED, 21,900
LUMENS
VMM9 LSL 16 MSL4 80CRI 40K ID1100LMF
20/80 DARK ZT 120 SCT F1/MCS 24A ___
RDEP
LED, 17,520
LUMENS
VMM9 LSL 8 MSL4 80CRI 40K ID1100LMF
20/80 DARK ZT 120 SCT F1/MCS 24A ___
RDEP
LED, 8,760
LUMENS
VMM9 LSL 12 MSL4 80CRI 40K ID1100LMF
20/80 DARK ZT 120 SCT F1/MCS 24A ___
RDEP
LED, 4,380
LUMENS
2BLT4 48L ADP EZ1 LP840
LED, 4,800
LUMENS
OR EQUAL
LITHONIA LIGHTING
C
2BLT2 33L ADP EZ1 LP840
OR EQUAL
D
LED, 3800
LUMENS
LITHONIA LIGHTING
LED, 2,000
LUMENS
LDN6 40/20 LO6AR LSS MVOLT EZ1
OR EQUAL
PEERLESS
LIGHTING
OR EQUAL
F2
PEERLESS
LIGHTING
OR EQUAL
G
LED, 3,300
LUMENS
LITHONIA LIGHTING CLX L48 4000LM SEF RDL MVOLT GZ10 40K
80CRI SPD120 WH HC36
OR EQUAL
E
F1
LED, 13,140
LUMENS
VMM9 LSL 4 MSL4 80CRI 40K ID1100LMF
20/80 DARK ZT 120 SCT F1/MCS 24A ___
RDEP
LITHONIA LIGHTING
B
LIGHT
SOURCE
8' SUSPENDED 20/80 INDIRECT/DIRECT FIXTURE,
WITH 0-10V DIMMING TO 1%, 24" OF ADJUSTABLE
AIRCRAFT SUSPENSION CABLE, ROUNDED END
CAP.
A
ARCHITECT
TO SELECT
12' SUSPENDED 20/80 INDIRECT/DIRECT FIXTURE,
WITH 0-10V DIMMING TO 1%, 24" OF ADJUSTABLE
AIRCRAFT SUSPENSION CABLE, ROUNDED END
CAP.
A
ARCHITECT
TO SELECT
4' SUSPENDED 20/80 INDIRECT/DIRECT FIXTURE,
WITH 0-10V DIMMING TO 1%, 24" OF ADJUSTABLE
AIRCRAFT SUSPENSION CABLE, ROUNDED END
CAP.
A
114
38
45
30
28
23
PENDANT @ 8-6"' A.F.F. TO
BTM OF FIXTURE
PENDANT @ 8-6"' A.F.F. TO
BTM OF FIXTURE
RECESSED
RECESSED
CHAIN @ 8' A.F.F.
RECESSED
STANDARD
STANDARD
WHITE
STANDARD
4000K
ARCHITECT
TO SELECT
8' STRIP LIGHT WITH 0-10V DIMMING.
OR EQUAL
LITHONIA LIGHTING
FMVCCL 24IN MVOLT 40K 90CRI __
OR EQUAL
GOTHAM LIGHTING
LED, 1750
LUMENS
LED, 2550
LUMENS
LED, 3400
LUMENS
4000K
4000K
4000K
LED, 1750
LUMENS
4000K
LED, 2400
LUMENS
4000K
LED, 1300
LUMENS
4000K
EVO 40/15 4AR MD LSS MVOLT EZ1
LED, 1500
LUMENS
EVO 40/20 4AR WD LSS MVOLT EZ1
LED, 2000
LUMENS
EVO WW 40/15 4AR LSS MVOLT EZ1
LED, 1500
LUMENS
EVO WW 40/20 4AR LSS MVOLT EZ1
LED, 2000
LUMENS
EVO WW 30/20 4AR LSS MVOLT EZ1
LED, 2000
LUMENS
3000K
MGL 24IN 6500LM 40K DARK ZT 120 CCV
LED, 6500
LUMENS
4000K
MGL 24IN 6500LM 30K DARK ZT 120 CCV
LED, 6500
LUMENS
OR EQUAL
GOTHAM LIGHTING
OR EQUAL
GOTHAM LIGHTING
OR EQUAL
GOTHAM LIGHTING
OR EQUAL
GOTHAM LIGHTING
OR EQUAL
MARK LIGHTING
OR EQUAL
MARK LIGHTING
OR EQUAL
4000K
4000K
4000K
4000K
3000K
120
120
120
120
120
120
120
120
120
120
120
120
120
56
18
27
36
20
24
18
18
25
18
25
25
68
68
SURFACE MOUNT
INDIRECT (AS NOTED)
INDIRECT (AS NOTED)
INDIRECT (AS NOTED)
WALL MOUNT
RECESSED
WALL MOUNT CENTERED
EITHER SIDE OF MIRROR
RECESSED
RECESSED
RECESSED
RECESSED
RECESSED
RECESSED
RECESSED
WHITE
20' SPOOL OF "DANALITE" FLEXIBLE STRIP LIGHT.
DIMMABLE WITH 2-WIRE FORWARD PHASE
COMPATIBLE DIMMERS. CUT ALL COMPONENTS TO
EQUAL ONE 6' SECTION OF PRODUCT.
E
WHITE
20' SPOOL OF "DANALITE" FLEXIBLE STRIP LIGHT.
DIMMABLE WITH 2-WIRE FORWARD PHASE
COMPATIBLE DIMMERS. CUT ALL COMPONENTS TO
EQUAL ONE 8' SECTION OF PRODUCT.
E
STANDARD
SCR 400 80 40 FL 2X2 W UNV DP
OR EQUAL
ELM2 LED SD
LED, 3200
LUMENS
4000K
LED
-
120
36
RECESSED
120
1.5
STANDARD
4" WALL WASH DOWNLIGHT WITH 0-10V DIMMING
TO 1%.
STANDARD
4" WALL WASH DOWNLIGHT WITH 0-10V DIMMING
TO 1%.
STANDARD
24" DIAMETER RECESSED LIGHT WITH CONCAVE
LENS AND 0-10V DIMMING TO 1%.
STANDARD
24" DIAMETER RECESSED LIGHT WITH CONCAVE
LENS AND 0-10V DIMMING TO 1%.
WHITE
WHITE
CEILING
BRUSHED
ALUMINUM
ELT-FT-AC-G-1C-BA-RC-NA
LED
GREEN
120
3
ISOLITE LIGHTING
ELT-FT-AC-G-1C-BA-RC-AR
LED
GREEN
120
3
CEILING
OR EQUAL
ISOLITE LIGHTING
ELT-FT-AC-G-1C-BA-RC-AL
LED
GREEN
120
3
CEILING
OR EQUAL
RATH
STANDARD
SINGLE SIDED AREA OF REFUGE SIGN
LED, 12,600
LUMENS
4000K
208
100
POLE @ 30'
ARCHITECT
TO SELECT
LED AREA LUMINAIRE WITH TYPE 3M DISTRIBUTION,
10kV SURGE PROTECTION, 3G VIBRATION RATING.
SSA 30 8J DM28AS FDL2B
-
-
-
-
REF. DETAIL 1 DRAWING
UE-4.1
ARCHITECT
TO SELECT
8" SQ. x 1/4" THK x 30' DUAL HEAD ALUMINUM POLE
WITH FESTOON OPENING.
FSPB
-
-
-
-
SEE DETAIL
ARCHITECT
TO SELECT
RIGHT ANGLE TENON FOR MOUNTING OF
FLOODLIGHTS "BB3".
SSA 30 5G DM19AS
-
-
-
-
SEE DETAIL
ARCHITECT
TO SELECT
5" SQ. x 3/16" THK x 30' SINGLE HEAD ALUMINUM
POLE.
LITHONIA LIGHTING
OR EQUAL
LITHONIA LIGHTING
OR EQUAL
LITHONIA LIGHTING
OR EQUAL
FO8O 1S HO 40 8 10 H A
LED, 745
LUMENS,
4,670 CBCP
4000K
120
11.5
REF. DETAIL 2 DRAWING
UE-4.1
ARCHITECT
TO SELECT
FLAG POLE FLOOD LIGHT 10° VERY NARROW SPOT
BEAM ANGLE, HALF SNOOT AND 19" FLYING LEAD
OPTIONS.
DSXF2 LED P1 40K FL MVOLT YKC62 UBV __
LED, 7,600
LUMENS, >
6,000 CBCP
4000K
120
54
REF. DETAIL 11 DRAWING
UE-4.1
ARCHITECT
TO SELECT
FLOOD LIGHT 60° FLOOD BEAM ANGLE, HALF VISOR
AND YOKE MOUNT.
38
TENON MOUNT TO AAP1A
ARCHITECT
TO SELECT
FLOOD LIGHT 15° X 60° BEAM ANGLE, HALF VISOR.
15
MOUNT AT 8' A.F.F. CNTRD
OVER DOOR
ARCHITECT
TO SELECT
3' LONG ARCHITECTURAL EXTERIOR WALL PACK
AND 0-10V DIMMING.
OR EQUAL
LITHONIA LIGHTING
BB2
OR EQUAL
BB3
ECOSENSE
LIGHTING
F170-1S-HO-40-8-E1-__-H-A
LED, 2900
LUMENS
AEL 36 15W 4000K 120-277 DP __ DIM TX/SD
LED, 1,300
LUMENS
OR EQUAL
LUMINAIRE LED
CC
OR EQUAL
LITHONIA LIGHTING
DD1
OLWX1 LED 13W 40K
OR EQUAL
LITHONIA LIGHTING
DD2
OLWX1 LED 20W 40K
OR EQUAL
WAC LIGHTING
EE
DS-WD05-S40S
OR EQUAL
BEGA LIGHTING
33065 K4
FF
OR EQUAL
LED EXIT FIXTURE ARROW LEFT.
WALL @ 80" A.F.F. TO TOP OF
SIGN
OR EQUAL
BB1
BRUSHED
ALUMINUM
LED EXIT FIXTURE ARROW RIGHT.
4
DSX1 LED 60C 530 40K T3M 208 SPA
ECOSENSE
LIGHTING
BRUSHED
ALUMINUM
LED EXIT FIXTURE NO ARROWS.
120
LITHONIA LIGHTING
AAP2
DUAL HEAD EMERGENCY LIGHT WITH EMERGENCY
BATTERY AND SELF TEST DIAGNOSTICS.
-
OR EQUAL
AAP1A
MOCP
CONDUIT
LINE
NEU
GND
F.D.S.
SIZE
FUSE
SIZE
ENCL
NEMA
REMARK
S/NOTES
CONDENSING UNIT
208V/3Ø
EXTERIOR MECHANICAL YARD
70,504
WATTS
195.7
225
-
2 12"
3 - #3/0
-
#6
3P400
-
-
3R
A
CU-1B
CONDENSING UNIT
208V/3Ø
EXTERIOR MECHANICAL YARD
70,504
WATTS
195.7
225
-
2 12"
3 - #3/0
-
#6
3P400
-
-
3R
A
AHU-1
AIR HANDLING UNIT
208V/3Ø
MECH/ELEC 222
31,415
WATTS
87.2
100
-
1 12"
3 - #1
-
#6
3P100
-
-
3R
A,B,F
OU-1
SPLIT SYSTEM - OUTDOOR UNIT
208V/1Ø
OUTSIDE EQUIP 105
2517
WATTS
12.1
15
-
1/2"
2 - #12
-
12
2P30
-
-
3R
A
IU-1
SPLIT SYSTEM - INDOOR UNIT
-
EQUIP 105
-
-
-
-
-
1/2"
2 - #12
-
12
TOGGLE
-
-
1
C
OU-2A
SPLIT SYSTEM - OUTDOOR UNIT
208V/1Ø
EXTERIOR MECHANICAL YARD
3432
WATTS
16.5
20
-
1/2"
2 - #12
-
12
2P30
-
-
3R
A
IU-2A
SPLIT SYSTEM - INDOOR UNIT
208V/1Ø
MDF 221
270
WATTS
1.3
15
-
1/2"
2 - #12
-
12
TOGGLE
-
-
1
A
OU-2B
SPLIT SYSTEM - OUTDOOR UNIT
208V/1Ø
EXTERIOR MECHANICAL YARD
3432
WATTS
16.5
20
-
1/2"
2 - #12
-
12
2P30
-
-
3R
A
IU-2B
SPLIT SYSTEM - INDOOR UNIT
208V/1Ø
MDF 221
270
WATTS
1.3
15
-
1/2"
2 - #12
-
12
TOGGLE
-
-
1
A
B-1A
BOILER
120V/1Ø
BOILER 124
1440
WATTS
12.0
15
-
1/2"
12
12
12
TOGGLE
-
-
1
A
B-1B
BOILER
120V/1Ø
BOILER 124
1440
WATTS
12.0
15
-
1/2"
12
12
12
TOGGLE
-
-
1
A
BP-1A
BOILER PUMP
120V/1Ø
BOILER 124
300
WATTS
2.5
15
-
1/2"
12
12
12
TOGGLE
-
-
1
A,F
BP-1B
BOILER PUMP
120V/1Ø
BOILER 124
300
WATTS
2.5
15
-
1/2"
12
12
12
TOGGLE
-
-
1
A,F
P-1A
HYDRONIC PUMP
208V/3Ø
BOILER 124
1.5
HP
4.3
15
-
1/2"
3 - #12
-
12
3P30
-
-
1
A
P-1B
HYDRONIC PUMP
208V/3Ø
BOILER 124
1.5
HP
4.3
15
-
1/2"
3 - #12
-
12
3P30
-
-
1
A
WH-1
TANKLESS WATER HEATER
120V/1Ø
BOILER 124
960
WATTS
8
15
-
1/2"
12
12
12
1P30
-
-
1
A
WH-2
TANKLESS WATER HEATER
120V/1Ø
BOILER 124
960
WATTS
8
15
-
1/2"
12
12
12
1P30
-
-
1
A
CP-1
CIRCULATING PUMP
120V/1Ø
BOILER 124
270
WATTS
2.3
15
-
1/2"
12
12
12
1P30
-
-
1
A
SP-1
ELEVATOR SUMP PUMP
120V/1Ø
ELEV 103
0.3
HP
9.7
15
-
-
-
-
-
-
-
-
-
D
DESCRIPTION
VOLTAGE
/PHASE
LOCATION
LOAD UNITS
LOCAL DISCONNECTING MEANS/CONTROL
CONDUCTORS
03/01/2018
MCA
MOCP
CONDUIT
LINE
NEU
GND
N.F.D.S.
SIZE
UNIT OPERATION CONTROL *7
F.D.S.
SIZE
FUSE
SIZE
STARTE
R SIZE
ENCL
NEMA
SWITCH
OCCUPANCY
ZONE LTG
CONTROL
DDC
BREAKER
REMARKS
/NOTES
EF-1
EXHAUST FAN
120V/1Ø
TOILET 101
59.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
-
X
-
-
E
EF-2
EXHAUST FAN
120V/1Ø
BOOK MOBILE 121
31.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
-
-
-
X
E
EF-3
EXHAUST FAN
120V/1Ø
STAFF TOILET 119
15.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
-
X
-
-
E
EF-4
EXHAUST FAN
120V/1Ø
CUSTODIAL 118
17.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
X
-
-
-
E
EF-5
EXHAUST FAN
120V/1Ø
WOMEN 117
121.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
-
X
-
-
E
EF-6
EXHAUST FAN
120V/1Ø
MEN 116
121.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
-
X
-
-
E
EF-7
EXHAUST FAN
120V/1Ø
BREAKROOM 223
99.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
X
-
-
-
E
EF-8
EXHAUST FAN
120V/1Ø
STAFF TOILET 219
15.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
-
X
-
-
E
EF-9
EXHAUST FAN
120V/1Ø
FAMILY 218
15.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
-
X
-
-
E
EF-10
EXHAUST FAN
120V/1Ø
MAKER 215
104.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
X
-
-
-
E
EF-11
EXHAUST FAN
120V/1Ø
WOMEN 216
121.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
-
X
-
-
E
EF-12
EXHAUST FAN
120V/1Ø
MEN 217
121.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
-
X
-
-
E
EF-13
EXHAUST FAN
120V/1Ø
UTILITY 202
128.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
X
-
-
-
E
EF-14
EXHAUST FAN
120V/1Ø
CATER 206
121.0
W
-
-
1/2"
12
12
12
-
-
-
-
-
X
-
-
-
E
RH-1
RANGE HOOD
120V/1Ø
BREAKROOM 223
216.0
W
1.8
-
1/2"
12
12
12
-
-
-
-
-
-
-
-
-
D
REF-15
EXHAUST FAN
208V/3Ø
MECH/ELEC 222
5.0
HP
14.2
25
1/2"
10
-
10
3P30
-
-
-
1
-
-
X
-
A
GENERAL NOTES:
1
THE INFORMATION ABOVE SHALL BE COORDINATED WITH THE MECHANICAL EQUIPMENT AS TAGGED ACTUAL EQUIPMENT REQUIREMENTS SHALL TAKE PRECEDENCE OVER THE LISTED INFORMATION. CONTRACTOR SHALL FURNISH AND
INSTALL ALL EQUIPMENT REQUIRED TO PLACE EQUIPMENT IN SERVICE. EQUIPMENT MANUFACTURER SHALL BE RESPONSIBLE FOR VARIATIONS IN ELECTRICAL FIELD CONNECTIONS DUE TO EQUIPMENT SUBSTITUTIONS - MODIFY
OVERCURRENT, DISC. SW, WIRE SIZE ETC, AS NECESSARY.
2
THIS SCHEDULE INCLUDES, BUT IS NOT LIMITED TO, THE EQUIPMENT FOUND ON THIS PROJECT, COORDINATE WITH ALL TRADES AND PROVIDE MANUFACTURERS MINIMUM REQUIREMENTS TO ALL EQUIPMENT INSTALLED. THIS SCHEDULE
IS NOT TO IMPLY QUANTITY OF EQUIPMENT, REFER TO CONSTRUCTION DOCUMENTS OF RESPECTIVE TRADE FOR LOCATION AND QUANTITIES.
3
REFER TO BUSSING DIAGRAM OF REFERENCED PANEL FOR CIRCUIT BREAKER SIZES.
4
STARTER/MOTOR SWITCH/DISCONNECT SHALL BE LOCATED ADJACENT TO UNIT IN ACCORDANCE WITH N.E.C. ARTICLE #110 & #440 - MAINTAIN WORKING CLEARANCES.
5
ALL FIELD WIRING TO UNITS SHALL BE PROPERLY SUPPORTED PER NEC AND ENCLOSURES SHALL BE PROPERLY RATED FOR THE INSTALLATION CONDITIONS. FIELD VERIFY PROPER BONDING TO GROUND.
6
CONTRACTOR IS RESPONSIBLE FOR INSTALLATION OF ANY EQUIPMENT SHIPPED LOOSE WITH UNIT, SUCH AS FAN SPEED CONTROLLERS - INSTALL PER MANUFACTURER'S RECOMMENDATIONS.
7
UNIT OPERATION CONTROL:
OCC. - UNIT SHALL BE CONTROLLED BY ZONE LIGHT CONTROL. COORDINATE INTERCONNECTION OF FAN TO LIGHTING POWER CIRCUIT WITH THE ELECTRICAL CONTRACTOR.
2'X2' ARCHITECTURAL TROFFER WITH 0-10V
DIMMING TO 1%.
LED
7050
AAP1
MCA
N.F.D.S.
SIZE
BRKR - UNIT SHALL BE CONTROLLED BY A DEDICATED SWITCH RATED BREAKER. ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL BREAKER.
DDC - FAN SHALL BE CONTROLLED BY TEMPERATURE CONTROL CONTRACTOR.
B
SPECIAL NOTES:
OR EQUAL
AA
4" DOWNLIGHT WITH 0-10V DIMMING TO 1%.
STANDARD
WALL @ 7.5' A.F.F.
ISOLITE LIGHTING
AR
LED VANITY FIXTURE.
4" WALL WASH DOWNLIGHT WITH 0-10V DIMMING
TO 1%.
OR EQUAL
EX3
6"x4' RECESSED LINEAR FIXTURE.
4" DOWNLIGHT WITH 0-10V DIMMING TO 1%.
LITHONIA LIGHTING
EX2
ELEVATOR PIT LIGHT
STANDARD
UNITS
LOCAL DISCONNECTING MEANS
CU-1A
ITEM #
E
ARCHITECT
TO SELECT
CONDUCTORS
LOAD
ELEC. DATA
WHITE
STANDARD
LOCATION
VENTILATING EQUIPMENT CONNECTION SCHEDULE
20' SPOOL OF "DANALITE" FLEXIBLE STRIP LIGHT.
DIMMABLE WITH 2-WIRE FORWARD PHASE
COMPATIBLE DIMMERS. CUT ALL COMPONENTS TO
EQUAL ONE 4' SECTION OF PRODUCT.
GRAY
ELEC. DATA
VOLTAGE
/PHASE
SWITCH - UNIT SHALL BE CONTROLLED BY INDEPENDENT SWITCH. ELECTRICAL CONTRACTOR SHALL FURNISH AND INSTALL SWITCH.
AXIS LIGHTING
EX1
6" DOWNLIGHT WITH 0-10V DIMMING TO 1%.
LED, 6,000
LUMENS
SL6L LOP 4FT FLP TG 80CRI 40K 600LMF 120
EM1
4' STRIP LIGHT WITH 0-10V DIMMING, SURGE
PROTECTION AND HANGER CHAIN OPTIONS.
4' 30% INDIRECT/70% DIRECT STAIRWELL LIGHT
WITH 0-10V DIMMING.
120
A
2'X2' VOLUMETRIC TROFFER WITH 0-10V DIMMING
TO 1%.
ARCHITECT
TO SELECT
DESCRIPTION
A
2'X4' VOLUMETRIC TROFFER WITH 0-10V DIMMING
TO 1%.
WALL @ 7' A.F.F.
MARK LIGHTING
P
ARCHITECT
TO SELECT
40
OR EQUAL
O2
76
PENDANT @ 8-6"' A.F.F. TO
BTM OF FIXTURE
120
68-02-20W-L-W-F-OG-09
O1
16' SUSPENDED 20/80 INDIRECT/DIRECT FIXTURE,
WITH 0-10V DIMMING TO 1%, 24" OF ADJUSTABLE
AIRCRAFT SUSPENSION CABLE, ROUNDED END
CAP.
4000K
CANLET
N3
120
ARCHITECT
TO SELECT
LED, 3,500
LUMENS
OR EQUAL
N2
4000K
120
152
PENDANT @ 8-6"' A.F.F. TO
BTM OF FIXTURE
SQW4 STW 4FT 80CRI 40K 1500LMF 400LMF
MIN10 ZT 120 SCT __ SCEP
SL412 20FT 40K 80CRI
N1
4000K
120
ARCHITECT
TO SELECT
4' 30% INDIRECT/70% DIRECT STAIRWELL LIGHT
WITH 0-10V DIMMING.
JUNO LIGHTING
M2
4000K
120
ITEM #
PENDANT @ 8-6"' A.F.F. TO
BTM OF FIXTURE
190
ARCHITECT
TO SELECT
OR EQUAL
M1
4000K
120
NOTES
20' SUSPENDED 20/80 INDIRECT/DIRECT FIXTURE,
WITH 0-10V DIMMING TO 1%, 24" OF ADJUSTABLE
AIRCRAFT SUSPENSION CABLE, ROUNDED END
CAP.
WALL @ 7' A.F.F.
SL412 20FT 40K 80CRI
L
4000K
120
REMARKS
60
JUNO LIGHTING
K
4000K
120
FINISH
120
OR EQUAL
J
4000K
120
MOUNTING
4000K
SL412 20FT 40K 80CRI
H3
4000K
120
INPUT
WATTS
LED, 4,850
LUMENS
JUNO LIGHTING
H2
4000K
VOLTAGE
SQW4 STW 4FT 80CRI 40K 1500LMF 800LMF
MIN10 ZT 120 SCT __ SCEP
LITHONIA LIGHTING TZL1F L96 SMR 6000LM MDD MVOLT 40K
80CRI __
OR EQUAL
H1
CCT
LED, 1,270
LUMENS
LED, 2,700
LUMENS
LED, >
11,000
CBCP
LED, 2,700
LUMENS
4000K
4000K
4000K
4000K
4000K
4000K
120
120
120
120
120
120
14
AS NOTED ON PLANS
DARK
BRONZE
20
AS NOTED ON PLANS
DARK
BRONZE
70
SOUTH FACADE AT 20' A.F.F..
REMAINING FIXTURES AT
LEVEL PLANE TO SOUTH
FACADE FIXTURES
ARCHITECT
TO SELECT
RECESSED IN WALL @ 12"
ABOVE SIDEWALK OR
GRADE
ARCHITECT
TO SELECT
11
B
SLIM PROFILE EXTERIOR WALL PACK, 0-10V
DIMMING.
E.C. SHALL FURNISH AND INSTALL UNIT WITH A NON-FUSED DISCONNECT MOUNTED LOCAL TO UNIT AND ON SUITABLE SUPPORT. E.C. SHALL MAKE SINGLE POINT CONNECTION FROM DISCONNECT TO UNIT POWER TERMINALS.
B
FIRE ALARM CONTRACTOR SHALL FURNISH A DUCT SMOKE DETECTOR FOR THE RETURN AIR DUCT. DUCT SMOKE DETECTOR SHALL BE COMPATIBLE WITH FIRE ALARM SYSTEM. MECHANICAL CONTRACTOR SHALL RECEIVE DUCT SMOKE
DETECTOR FROM FIRE ALARM CONTRACTOR AND INSTALL IN DUCTWORK IN AN ACCESSIBLE LOCATION AND ACCORDANCE WITH THE INTERNATIONAL MECHANICAL CODE. DUCT SMOKE DETECTOR SHALL BE INTERLOCKED WITH HVAC
UNIT AND FIRE ALARM SYSTEM TO SHUT DOWN THE UNIT OPERATION AND GENERATE A GENERAL ALARM CONDITION WHEN SMOKE IS SENSED IN THE DUCT.
C
OU SUPPLIES POWER TO IU. E.C. SHALL FURNISH AND INSTALL CONDUIT, WIRE AND TOGGLE TO MAKE CONNECTION BETWEEN UNITS.
D
UNIT SHALL BE PROVIDED WITH 120VAC CORD AND PLUG. E.C. SHALL FURNISH AND INSTALL DEDICATED RECEPTACLE AS NOTED IN PLANS FOR THE PUMP. UNIT SHALL BE DIRECTLY PLUGGED INTO RECEPTACLE. EXTENSION CORD USE
IS NOT ACCEPTABLE.
E
UNIT PROVIDED WITH SOLID-STATE FAN SPEED CONTROL. COORDINATE INSTALLATION OF FIELD INSTALLED SPEED CONTROLLERS WITH MECHANICAL CONTRACTOR. E.C. SHALL FURNISH AND INSTALL ALL COMPONENTS (BACK BOXES,
CONDUIT, ETC.) REQUIRED FOR OPERATION OF CONTROLLER.
F
UNIT PROVIDED WITH VARIABLE FREQUENCY DRIVE (VFD).
B
B, C
B
D
GENERAL NOTES:
1
PRIOR APPROVAL REQUIRED A MINIMUM OF 10 DAYS PRIOR TO BID - EQUALS TO BE LISTED BY ADDENDA.
2
OTHER LIGHT FIXTURES MANUFACTURERS THAT ARE CONSIDERED AS EQUALS FOR GENERAL LIGHTING REQUIREMENTS ARE:
A. COOPER LIGHTING AND SUB-PRODUCT LINES AS SUPPLIED BY ENGINEERED LIGHTING SALES
B. HUBBELL LIGHTING AND SUB-PRODUCT LINES AS SUPPLIED BY LUMENATION
C. ACUITY BRAND AND SUB-PRODUCT LINES AS SUPPLIED BY LHI LIGHTING SALES
ALL LIGHT FIXTURES SHALL BE SUBJECT TO SHOP DRAWING REVIEW BY ARCHITECT AND ENGINEER FOR ACCEPTANCE AS TO ENERGY EFFICIENCY, APPEARANCE, STYLE, PERFORMANCE, AND OVER
ALL SERVICEABILITY.
3
SLIM PROFILE EXTERIOR WALL PACK, 0-10V
DIMMING.
A
F
FIXTURES SHALL BE SUPPORTED PER "LAY-IN FIXTURE SEISMIC SUPPORT DETAIL 2, DRAWING E-4.1.
SPECIAL NOTES:
A
SECURE PRODUCT "SUPPORTS" PER SPECIFICATIONS.
B
PROVIDE WITH NOTED CIRCUIT FROM GENERATOR PANEL LS.
C
CONTRACTOR SHALL COORDINATE DIRECTION ARROWS OF ALL EXIT SIGNS WITH ARROWS INDICATED ON PLANS AND FIELD ADJUST THE FIXTURE'S CHEVRON INDICATORS TO MATCH.
D
E.C. SHALL FURNISH AND INSTALL WEATHERPROOF, WEATHER RESISTANT, WHILE IN-USE GFCI RECEPTACLE AT LOCATION OF FESTOON OPENING IN POLE.
E
AS REQUIRED, ORDER WITH "CUTTING TOOL #SLCUTTER; REMOTE POWER SUPPLY #DLDPS 40W ECOS2; 36" STARTER CABLE; 72" JOINER CABLE #SL102FLX 72IN; SURFACE MOUNT ALUMINUM CHANNEL
#SM1 48IN FR WH; MOUNTING CLIPS #SLCLIP (AS REQUIRED). REFERENCE DRAWING E-1.1 FOR SPECIFIC INSTALLATION/ORDERING INSTRUCTIONS AND QUANTITIES.
F
POSITION MOUNTING OF AAP1A AND BB3 ON POLE AAP1 WHERE NADIR (0°) OF A FULLY PERPENDICULAR MOUNTED BB3 IS LOCATED IN A PLANE 1' HIGHER THAN CANOPY MOUNTED "MARSHALL COUNTY
PUBLIC LIBRARY" SIGN. BB3'S SHALL BE ADJUSTED IN THE FIELD TO OPTIMIZE AIM LIGHT PATTERNING OVER SIGN.
ARCHITECTURAL EXTERIOR WALLPACK WITH
UP/DOWN LIGHTING, 18° B.A., 0-10V DIMMING.
LED STEP LIGHT
ELECTRICAL SCHEDULES
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-5.1
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
nECY
nBRG 8
GFX
CATER 206
BLUE
OS
S
DC1
HOT NEU
PANEL RA-11
STUDY 208
NEU HOT PANEL GP-8
EM
R
NEU
0-10V DIM
GRY
NEU HOT
PANEL RA-11
EM
0-10V DIM
BLUE
GRN
LIGHTING LOAD
VIO
WHT/RED
WHT/RED
GY
LIGHTING LOAD
NEU HOT
PANEL RA-20
R
NEU
FIXTURES "B"
DESIGNATED AS
EMERGENCY
OS
LOAD
BLUE
GRN
S
NEU HOT PANEL GP-8
EM
BLK
R
NEU
FIXTURES "B"
DESIGNATED AS
EMERGENCY
VI
DC1
NEU HOT
PANEL RA-20
BLK
YEL
BLU
WHT/RED
NEU HOT
PANEL RA-11
GRN
0-10V DIM
BLUE
GRN
LIGHTING LOAD
GRY
BLK
BLUE
C1
R
NEU
0-10V DIM
VIO
S
DS
C1
NEU HOT PANEL LS-25
WHITE
OS
EM
WHT
S
GY
BLUE
BLK
BLUE
PORT4
PORT3
PORT2
PORT1
R
WHITE
24V -
PORT7
PORT6
PORT5
VI
S
VIO
R
NEU
FIXTURES "G"
S
OS
S
DC1
HOT NEU
PANEL RA-20
GRY
BLUE
GRN
C1
HOT NEU
PANEL RA-11
YEL
BLU
NEU HOT
PANEL RA-20
LIGHTING LOAD
0-10V DIM
NEU
FIXTURES "C"
WHT
DC1
STUDY 205
BLK
GRN
OS
NEU
0-10V DIM
WHT/RED
S
03/01/2018
BLK
LIGHTING LOAD
BLUE
NEU
0-10V DIM
GY
BLK
BLUE
DS
BLUE
NEU
0-10V DIM
WHITE
BLUE
VI
R
WHT
OS
R
GRN
GY
YEL
BLU
OS
VI
BLK
BLUE
FIXTURES "C"
DESIGNATED AS
EMERGENCY
GRN
GY
NEU HOT PANEL LS-25
nGWY2
24V +
NEU
MENS 217
RED
BLK
PS
150
R
HOT NEU
PANEL RA-20
WOMENS 216
BLK
WHT
VI
WHITE
GRN
LIGHTING LOAD
GRN
0-10V DIM
BLUE
NEU HOT
PANEL RA-20
HOT NEU
PANEL RA-20
YEL
BLU
R
NEU
GRY
YEL
BLU
0-10V DIM
VIO
BLK
BLUE
BLUE
OS
WHT/RED
EM
WHT
NEU HOT
PANEL RA-20
PANEL RA-11
LINE IN
NEUTRAL IN
GROUND
OS
GY
WHITE
GRN
R
NEU
FIXTURES "C"
DESIGNATED AS
EMERGENCY
VI
WHT
LIGHTING LOAD
0-10V DIM
BLUE
GRN
BLK
R
NEU
GRY
BLK
BLUE
0-10V DIM
VIO
NEU HOT PANEL LS-25
WHITE
BLK
BLUE
WHITE
BLUE
EM
WHT
R
CAT5e Cable
(Typ.)
GY
WHT/RED
VI
BLK
GRN
YEL
BLU
NEU HOT PANEL LS-25
RJ45 (Typ.)
OS
C1
HOT NEU
PANEL RA-20
REMOTE
OVERIDE
PORT8
RS-485 TO BACNET SYSTEM
BREAKROOM 223
CORRIDOR 225
MDF 221
TECH LAB 220
ETHERNET TO PATCH PANEL
AT RACK IN MDF
NEU HOT PANEL LS-27
NEU HOT
PANEL RA-12
NEU HOT
PANEL RA-12
BOOK KEEPER 211
DIRECTOR 210
DC1
WHT/RED
NEU HOT
PANEL RA-19
VI
R
NEU
FIXTURES "B"
DESIGNATED AS
EMERGENCY
S
OS
DC2
HOT NEU
PANEL RA-19
VI
R
BLUE
S
C1
GRN
GY
0-10V DIM
NEU
LOAD
LIGHTING LOAD
FIXTURES "O1"
NEU HOT
PANEL RA-19
NEU HOT
PANEL RA-19
0-10V DIM
NEU
FIXTURES "O1"
DESIGNATED AS
EMERGENCY
C1
HOT NEU
PANEL RA-19
GRY
0-10V DIM
BLUE
GRN
GRN
R
NEU
FIXTURES "A"
DESIGNATED AS
EMERGENCY
OS
S
S
C1
S
C1
C1
HOT NEU
PANEL RA-18
HOT NEU
PANEL RA-18
VI
GY
BLUE
WHITE
WHT
R
NEU
LIGHTING LOAD
FIXTURES "M2"
VIO
WHT
0-10V DIM
BLUE
NEU HOT
PANEL RA-18
EM
YEL
BLU
GRY
WHT/RED
VIO
0-10V DIM
NEU
LOAD
LIGHTING LOAD
OS
OS
S
C1
NEU HOT
PANEL RA-18
A/V-STACKS 209
MEETING STORAGE 207
NEU HOT
PANEL RB-1
NEU HOT
PANEL RB-1
WHT
FIXTURE "A"
DESIGNATED AS
EMERGENCY
OS
R
BLUE
S
OS
DC4
HOT NEU
PANEL RB-1
0-10V DIM
NEU
LOAD
LIGHTING LOAD
FIXTURES "M1"
BLUE
NEU HOT
PANEL RB-35
NEU HOT
PANEL RD-26
S
DC1
HOT NEU
PANEL RD-26
BLUE
0-10V DIM
NEU
LOAD
LIGHTING LOAD
EM
R
0-10V DIM
NEU
LOAD
GRN
LIGHTING LOAD
FIXTURES "A"
VIO
BLUE
NEU HOT
PANEL RB-35
BLUE
GRY
0-10V DIM
NEU
FIXTURE "A"
DESIGNATED AS
EMERGENCY
OS
HOT NEU
PANEL RB-35
R
GRN
NEU HOT
PANEL RA-20
BLUE
HOT NEU
PANEL RD-20
GRY
EM
0-10V DIM
R
NEU
FIXTURE "B"
DESIGNATED AS
EMERGENCY
YEL
BLU
YEL
BLU
VIO
WHT/RED
EM
OS
GRN
WHT
R
GY
WHT/RED
YEL
BLU
0-10V DIM NEU
BLUE
FIXTURES "B, C & E"
DESIGNATED AS
EMERGENCY
COORIDOR 201
1
R
GY
NEU HOT PANEL LS-28
BLK
GRN
NEU HOT
PANEL RD-26
EXTERIOR WALL PACKS
WHT/RED
R
VI
WHT
LIGHTING LOAD
FIXTURE "B" &
"C"
NEU
GRN
BLK
0-10V DIM
GRY
BLK
BLUE
BLUE
VIO
NEU HOT PANEL LS-28
WHITE
R
EM
WHT
LIGHTING LOAD
FIXTURE "EE"
NEU
GY
BLK
0-10V DIM
BLK
BLUE
BLK
BLUE
BLUE
VI
WHITE
R
GRN
GY
VI
MEETING ROOM B 204
NEU HOT PANEL LS-28
VI
0-10V DIM
NEU
LOAD
LIGHTING LOAD
FIXTURES "M1"
NEU HOT
PANEL RB-35
MEETING ROOM A 203
GRN
GRN
GY
WHT/RED
VI
BLK
R
NEU
GRN
GY
BLK
BLUE
0-10V DIM
BLUE
VI
WHITE
GRN
BLK
BLUE
BLUE
GRY
WHITE
R
0-10V DIM
NEU
LOAD
GRN
LIGHTING LOAD
FIXTURES "A"
VIO
BLK
BLUE
EM
BLK
0-10V DIM
NEU
LOAD
LIGHTING LOAD
FIXTURES "M1"
GY
NEU HOT PANEL LS-28
WHITE
R
BLUE
NEU HOT
PANEL RB-1
VI
YEL
BLU
GRN
GY
BLK
BLUE
0-10V DIM
NEU
LOAD
LIGHTING LOAD
FIXTURES "M1"
WHITE
DC4
BLK
BLUE
S
R
BLUE
WHITE
OS
VI
WHITE
R
GRN
GY
BLK
BLUE
VI
WHT/RED
NEU HOT PANEL LS-28
GRN
S
OS
NEU HOT PANEL LS-27
BLK
R
0-10V DIM
NEU
LOAD
GRN
LIGHTING LOAD
FIXTURES "A"
YEL
BLU
WHT/RED
EM
BLK
BLK
BLUE
LIGHTING LOAD
FIXTURES "M2"
NEU HOT
PANEL RA-18
GY
BLUE
NEU
0-10V DIM
BLUE
GRY
WHT
REMOTE
OVERIDE
VI
R
BLUE
LIGHTING LOAD
FIXTURES "N2"
NEU HOT
PANEL RA-18
GRN
GY
WHITE
C1
R
NEU
0-10V DIM
BLK
BLUE
S
DC4
BLK
BLUE
S
WHITE
OS
BLUE
VI
WHITE
R
GRN
GY
R
0-10V DIM
NEU
LOAD
GRN
LIGHTING LOAD
FIXTURES "M2"
VIO
MAKER 215
NEU HOT PANEL GP-8
VI
EM
BLUE
COMPUTER LAB 214
GRN
GY
YEL
BLU
YEL
BLU
0-10V DIM
BLUE
GRN
GRN
WHT
LIGHTING LOAD
GRY
BLK
S
R
NEU
0-10V DIM
VIO
BLK
BLUE
BLUE
EM
NEU HOT PANEL LS-27
YEL
BLU
HOT NEU
PANEL RA-19
GY
NEU
0-10V DIM
LIGHTING LOAD
BLK
BLUE
WHITE
DS
WHITE
WHT
LIGHTING LOAD
BLK
BLUE
NEU HOT
PANEL RA-19
R
NEU
FIXTURES "B"
DESIGNATED AS
EMERGENCY
VI
BLK
0-10V DIM
BLUE
GRN
GRN
BLK
BLUE
WHT/RED
GRY
WHITE
DC1
0-10V DIM
VIO
R
NEU
LIGHTING LOAD
BLK
BLUE
S
EM
BLUE
NEU
0-10V DIM
GY
NEU HOT PANEL LS-27
PARTION WALL
COMMISSIONING
2.1 E.C. SHALL INCLUDE IN BID ALL COSTS ASSOCIATED WITH START UP COMMISSIONING OF SYSTEM AND
OWNER TRAINING ON UTILIZATION OF SYSTEM. COORDINATE WITH MANUFACTURER AND MANUFACTURER'S
REP FOR SOLICITATION OF FIELD COMMISSIONING AGENT FOR SYSTEM PROGRAMMING AND TRAINING.
2.2 E.C. SHALL ALSO COORDINATE WITH COMMISSIONING AGENT, OWNER AND ENGINEER ONCE PRODUCT IS
INSTALLED AND PRIOR TO THE ACTUAL PROGRAMMING OF SYSTEM. THIS COORDINATION IS INTENDED TO
ENSURE THAT PROGRAMMING OF "SEQUENCE OF OPERATIONS" MEETS ALL EXPECTATIONS BY ALL PARTIES
INVOLVED.
2.3 nLIGHT "SENSORVIEW" IS A WEB-BASED SUITE OF APPLICATIONS THAT GIVES AUTHORIZED USERS THE
ABILITY TO REMOTELY CONFIGURE AND MONITOR nLIGHT LUMINAIRES. SOFTWARE SHALL BE LOADED ON
OPERATIONS ENGINEER'S COMPUTER FOR CONTROL OF LIGHTING.
BLUE
WHITE
OS
GY
BLK
R
WHITE
2.
VI
YEL
BLU
NEU HOT PANEL LS-27
GRN
DS
VESTIBULE 212
NOTES:
GENERAL
1.1. DETAIL IS PURELY DIAGRAMMATIC AND FOR REFERENCE ONLY. E.C. SHALL COORDINATE WITH
MANUFACTURER AND MANUFACTURER'S REP., FURNISH AND INSTALL ALL COMPONENTS FOR A FULLY
FUNCTIONAL SYSTEM.
1.2. VERIFY IN FIELD ALL RUNS PRIOR TO COMMISSIONING & PROGRAMMING. CONTACT YOUR REPRESENTATIVE
WITH ANY QUESTIONS PRIOR TO INSTALLATION.
1.3
COORDINATE WITH MECHANICAL CONTRACTOR FOR INTERFACING WITH HVAC CONTROLS. FURNISH AS
REQUIRED DRY CONTACTS FOR EACH ROOM FOR INDICATION OF OCCUPANCY.
OS
FIXTURES "C"
DESIGNATED AS
EMERGENCY
VI
R
BLUE
HOT NEU
PANEL RA-12
RESEARCH 213
1.
WHT/RED
NEU HOT
PANEL RA-12
R
NEU
GRN
GY
WHT/RED
NEU HOT
PANEL RA-12
LIGHTING LOAD
VI
BLK
BLUE
OS
OS
0-10V DIM
BLUE
GRN
GRN
WHITE
LIGHTING LOAD
R
NEU
0-10V DIM
GRY
BLK
BLUE
NEU HOT
PANEL RA-12
BLUE
NEU
0-10V DIM
VIO
WHITE
DC2
LIGHTING LOAD
BLK
BLUE
WHITE
S
R
BLUE
NEU
0-10V DIM
VI
EM
WHT
R
BLUE
LOCATED IN MECH/ELEC 222
TO PORT8 OF nBRG 8
LOCATED IN BOILER 124
VI
GY
BLK
R
GRN
GY
YEL
BLU
VI
GRN
GY
WHT
GRN
BLK
BLUE
nBRG KIT
WHITE
BLK
RED
BLK
BLUE
TC
PS
150
WHITE
BLK
WHITE
LOAD
NEU
BLUE
FIXTURES "CC, DD1
& EE" DESIGNATED
AS EMERGENCY
HOT NEU
PANEL RD-26
UTILITY 202
EXTERIOR
LIGHTING CONTROLS SCHEMATIC
NO SCALE
ELECTRICAL SCHEDULES
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-5.2
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
nBRG 8
R
NEU
OS
NEU HOT
PANEL RD-14
NEU HOT
PANEL RD-14
STORAGE 125
C1
0-10V DIM
NEU
LOAD
LIGHTING LOAD
GRY
0-10V DIM
BLUE
GRN
NEU
FIXTURES "E"
DESIGNATED AS
EMERGENCY
OS
HOT NEU
PANEL RD-14
NEU HOT
PANEL RD-14
REMOTE
OVERIDE
VIO
R
BLUE
S
WHT/RED
YEL
BLU
WHT/RED
EM
BLK
OS
GY
BLK
BLUE
OS
HOT NEU
PANEL RD-14
NEU HOT
PANEL RD-14
VI
R
NEU
FIXTURES "C"
DESIGNATED AS
EMERGENCY
WHT
OS
GRN
GRN
0-10V DIM
BLUE
BLK
OS
GRY
WHITE
C1
LIGHTING LOAD
VIO
R
0-10V DIM
NEU
LOAD
LIGHTING LOAD
FIXTURES "E"
DESIGNATED AS
EMERGENCY
NEU HOT PANEL LS-27
CORRIDOR 123
STAIR 110
NEU HOT PANEL LS-27
NEU HOT PANEL LS-27
OS
S
S
C1
OS
C1
DC2
S
C1
HOT NEU
PANEL RD-15
BLUE
LIGHTING LOAD
0-10V DIM
NEU HOT
PANEL RD-15
NEU HOT
PANEL RD-15
GRN
OS
BLUE
0-10V DIM
R
LOAD
NEU
BLUE
FIXTURES "CC" &
"DD1"DESIGNATED
AS EMERGENCY AT
DOCK
YEL
BLU
WHT/RED
EM
VIO
R
NEU
BLUE
S
C1
EM
0-10V DIM
YEL
BLU
WHT/RED
VIO
R
NEU
BLUE
GRN
LIGHTING LOAD
YEL
BLU
WHT/RED
GY
S
OS
DC4
GRY
0-10V DIM
NEU
FIXTURES "G"
DESIGNATED AS
EMERGENCY
OS
OS
OS
HM
HM
HM
S
S
C1
C1
HOT NEU
PANEL RD-17
NEU HOT
PANEL RD-17
BOOK MOBILE 121
GRN
LIGHTING LOAD
GRY
0-10V DIM
BLUE
NEU
FIXTURES "C"
DESIGNATED AS
EMERGENCY
WHT
OS
GY
BLK
VI
R
NEU
BLK
BLUE
0-10V DIM
HOT NEU
PANEL RD-17
NEU HOT
PANEL RD-17
VI
HOT NEU
PANEL RD-17
GRN
FIXTURES "C"
DESIGNATED AS
EMERGENCY
WHT
GRN
FIXTURES "H"
DESIGNATED AS
EMERGENCY
NEU HOT PANEL LS-27
GRY
BLUE
GRN
EXTERIOR LIGHTING
WHITE
YEL
BLU
WHT/RED
R
NEU
LIGHTING LOAD
BLK
BLUE
WHITE
0-10V DIM
VIO
BLK
VI
BLUE
NEU
NEU HOT
PANEL RD-14
WHT
FIXTURES "B"
DESIGNATED AS
EMERGENCY
NEU HOT PANEL LS-27
EM
GRN
LIGHTING LOAD
FIXTURES "H"
LOAD
NEU HOT PANEL LS-27
YEL
BLU
R
NEU
WHT
0-10V DIM
COORDIOR OFF COLLECTIONS
GY
BLUE
NEU HOT
PANEL RD-14
WHITE
EM
HOT NEU
PANEL RD-16
BRANCH MNGR 115
R
WHT/RED
GRY
BLUE
GRN
LIGHTING LOAD
YEL
BLU
WHT/RED
R
NEU
NEU HOT
PANEL RD-16
NEU HOT
PANEL RD-16
GRN
R
NEU
NEU HOT PANEL LS-27
BLK
DS
0-10V DIM
VIO
WHT
BLUE
EM
BLK
R
NEU
GY
BLK
BLUE
C1
0-10V DIM
VI
LIGHTING LOAD
BLK
BLUE
WHITE
BLUE
S
GRN
GY
WHITE
R
LOAD
CHILDREN/JUVENILE 107
NEU HOT PANEL LS-25
VI
BLUE
LIGHTING LOAD
WORKROOM 114
GRN
R
NEU
BLK
NEU HOT
PANEL RD-15
R
NEU
EM
BLK
BLUE
S
0-10V DIM
GRN
GY
WHITE
FIXTURES "B"
DESIGNATED AS
EMERGENCY
BLUE
VI
BLK
BLUE
R
NEU
GRN
GY
WHITE
GRN
LIGHTING LOAD
0-10V DIM
BLUE
VI
BLK
BLUE
C1
R
NEU
GRN
BLK
BLUE
S
0-10V DIM
GRY
WHITE
WHITE
BLUE
VIO
BLK
BLUE
EM
WHITE
R
LOCATED IN BOILER 124
GY
WHT
VI
YEL
BLU
GRN
BLK
nBRG KIT
WHT/RED
RED
OS
OS
HOT NEU
PANEL RD-17
NEU HOT
PANEL RD-17
WOMENS 117
MENS 116
NEU HOT PANEL GP-26
C1
HOT NEU
PANEL RD-21
R
NEU
LIGHTING LOAD
BLUE
0-10V DIM
NEU
R
LIGHTING LOAD
NEU HOT
PANEL RD-16
NEU HOT
PANEL RD-16
GY
BLUE
EM
0-10V DIM
LIGHTING LOAD
VIO
R
NEU
BLUE
GRN
NEU HOT
NEU HOT
PANEL RD-18
NEU HOT
PANEL RD-18
NEU HOT
PANEL RD-18
PANEL RD-18
NEU
FIXTURES "E"
DESIGNATED AS
EMERGENCY
OS
S
DC4
0-10V DIM
NEU
R
LIGHTING LOAD
FIXTURES "A"
ZONE 4
BLUE
NEU HOT
PANEL RD-20
NEU HOT
PANEL RD-20
0-10V DIM
LIGHTING LOAD
FIXTURES "E"
ZONE 4
NEU
R
BLUE
NEU HOT
PANEL RD-19
0-10V DIM
NEU
LIGHTING LOAD
FIXTURES "A"
ZONE 5
R
BLUE
0-10V DIM
LIGHTING LOAD
FIXTURES "A"
ZONE 6
NEU HOT
PANEL RD-19
NEU
YEL
BLU
WHT/RED
VIO
R
GRN
BLUE
NEU HOT PANEL LS-25
GRY
EM
0-10V DIM
NEU
FIXTURES "E"
DESIGNATED AS
EMERGENCY
HOT NEU
PANEL RD-18
VIO
R
GRN
BLUE
WHT
BLUE
EM
WHT
R
GY
BLK
LIGHTING LOAD
FIXTURES "E"
ZONE 2
NEU
VI
BLK
BLUE
0-10V DIM
GRN
GY
WHITE
LIGHTING LOAD
FIXTURES "A"
ZONE 2
BLUE
VI
BLK
BLUE
R
NEU
GRN
GY
WHITE
0-10V DIM
VI
BLK
BLUE
BLUE
GRN
GY
WHITE
LIGHTING LOAD
FIXTURES "A"
ZONE 1
R
VI
BLK
BLUE
NEU
GRN
GY
WHITE
LIGHTING LOAD
FIXTURES "N1"
0-10V DIM
VI
BLK
BLUE
BLUE
GRN
GY
WHITE
DC4
R
NEU
VI
BLK
BLUE
S
0-10V DIM
GRN
GY
WHITE
WHITE
BLUE
VI
BLK
BLUE
R
GRN
GY
WHITE
VI
0-10V DIM
YOUTH PROGRAM 109
NEU HOT PANEL LS-25
GRN
GRY
HOT NEU
PANEL RD-16
NEU HOT
PANEL RD-16
YOUNG ADULTS 108
WHT/RED
VI
WHT
S
0-10V DIM
GRN
GY
BLK
BLUE
VI
BLK
BLUE
YEL
BLU
FIXTURES "E"
DESIGNATED AS
EMERGENCY
DC2
NEU HOT
PANEL RD-21
CIRCULATION 112
WHT/RED
S
R
NEU
GRN
GY
YEL
BLU
REMOTE
OVERIDE
GRN
LIGHTING LOAD
FIXTURES "E"
0-10V DIM
BLUE
VI
WHT/RED
NEU HOT
PANEL RD-21
R
NEU
GRN
WHITE
LIGHTING LOAD
FIXTURES "A"
ZONE 3
0-10V DIM
GRY
BLK
NEU HOT
PANEL RD-16
DC2
BLUE
VIO
BLK
BLUE
C1
S
R
NEU
EM
WHITE
S
0-10V DIM
GY
BLK
BLUE
LIGHTING LOAD
FIXTURES "M1"
BLUE
VI
WHITE
R
NEU
GRN
GY
WHT
0-10V DIM
VI
BLK
BLUE
WHITE
HOT NEU
PANEL RD-16
GRN
GY
BLK
BLUE
R
NEU
LIGHTING LOAD
FIXTURES "C"
WHT
BLK
GRN
0-10V DIM
VI
WHITE
BLUE
GRN
BLK
BLUE
R
GRY
WHITE
VIO
BLK
BLUE
YEL
BLU
WHT/RED
EM
YEL
BLU
NEU HOT PANEL LS-25
NEU HOT PANEL LS-25
BLK
BLUE
GRY
0-10V DIM
NEU
FIXTURES "E"
DESIGNATED AS
EMERGENCY
HOT NEU
PANEL RD-20
COLLECTIONS 106
R
GRN
BLK
BLUE
WHITE
BLUE
LIGHTING LOAD
FIXTURES
"BB1"
NEU HOT
PANEL RD-20
EXTERIOR FLAG POLE LIGHTS
NEU
VI
R
GY
BLUE
BLK
BLUE
GRN
WHITE
BLK
GRN
NEU
STAIR 104
EM
BLUE
NEU
BLK
BLUE
DS
0-10V DIM
GY
VI
R
BLUE
S
GRN
GY
0-10V DIM
HOT NEU
PANEL RD-22
VESTIBULE 101
WHITE
R
NEU
BLK
BLUE
DS
0-10V DIM
LIGHTING LOAD
BLK
BLUE
WHITE
BLUE
VI
WHITE
R
GRN
GY
VI
BLK
BLUE
PS
150
OS
GRY
BLUE
NEU HOT PANEL LS-27
BM OFFICE 122
BLK
WHITE
0-10V DIM
NEU
LOAD
LIGHTING LOAD
NEU HOT
PANEL RD-22
PORT8
RD-14
LINE IN
NEUTRAL IN
GROUND
VIO
R
BLUE
HOT NEU
PANEL RD-22
EXTERIOR ENTRY
EM
YEL
BLU
YEL
BLU
FIXTURES "P"
DESIGNATED AS
EMERGENCY
GY
WHT/RED
VI
03/01/2018
WHT
GRN
LIGHTING LOAD
FIXTURE "P"
0-10V DIM
BLUE
NEU HOT
PANEL RD-22
HOT NEU
PANEL RD-22
& "BB3"
R
NEU
GRN
BLK
FIXTURES "E"
DESIGNATED AS
EMERGENCY
0-10V DIM
GRY
BLK
BLUE
BLUE
VIO
WHITE
EM
WHT
R
NEU
GY
WHT/RED
VI
NEU HOT PANEL LS-25
WHT
NEU HOT
PANEL RD-22
20A
CONTACTS
TO FIXTURES "AA"
0-10V DIM
BLUE
GRN
LIGHTING LOAD
FIXTURE "E"
GRN
BLK
R
NEU
GRY
BLK
BLUE
0-10V DIM
VIO
WHITE
EM
NEU HOT PANEL LS-25
YEL
BLU
EXTERIOR SITE AND FLOOD LIGHTS
PORT7
PORT6
PORT5
TO PORT1 OF nBRG 8
LOCATED IN MDF/ELEC 222
WHITE
BLK
BLUE
CONTACTOR
GRN
PORT4
PORT3
PORT2
PORT1
BLUE
COIL
NEU HOT
PANEL RD-22
GY
WHT
R
BLUE
WHITE
CONTACTOR NOTE
:
CONTACTOR SHALL BE ELECTRICALLY HELD MULTI-POLE
EQUAL TO SQUARE "D" CLASS 8903 TYPE #LG SERIES (OR
APROVED EQUAL) WITH 120 VOLT COIL AND CONTACTS
RATED FOR 600V. CONTACTORS SHALL BE NEMA 1 WITH
SWITCH IN COVER FOR MAINTENANCE MANUAL OVERRIDE
- COORDINATE THE NUMBER OF POLES REQUIRED WITH
CIRCUITRY INDICATED ON THE LIGHTING PLANS - PROVIDE
ADDITIONAL CONTACTORS AS NECESSARY. CONTACTOR
SHALL BE CONTROLLED BY THE OUTPUT OF THE DIGITAL
RELAY.
VI
BLK
BLUE
R
GRN
WHT/RED
GRN
BLK
RD-23
RD-25
CAT5e Cable
(Typ.)
YEL
BLU
NEU HOT PANEL LS-25
RJ45 (Typ.)
0-10V DIM
NEU
LIGHTING LOAD
FIXTURE "BB2"
NEU HOT
PANEL RD-19
EXTERIOR FLOOD LIGHT FOR BLDG MTD SIGN
1
LIGHTING CONTROLS SCHEMATIC
ELECTRICAL SCHEDULES
NO SCALE
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-5.3
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
LIGHTING CONTROL NARRATIVE
MANUAL
ON
ROOM
NUMBER
ROOM TITLE
101
VESTIBULE
102
BOOK RETURN
X
103
ELEV.
x
104
STAIR
105
EQUIP.
106
107
108
109
MANUAL
OFF
110
STAIR
111
TOILET
MULTI
ZONE
SWITCH
KEY
SWITCH
X
TIME
CLOCK
ON
TIME
CLOCK
OFF
x
x
OCCUPANCY
SENSOR ON
OCCUPANCY
SENSOR OFF
X
X
x
PHOTOCONTROL
SWITCHING
PHOTOCONTROL
DIMMING
EXTERIOR
PHOTOCELL
ON/OFF
WIRING
DIAGRAM
REFERENCE
SEQUENCE
OF
OPERATIONS
1 / E-5.3
9
MANUF.
2
-
4
1 / E-5.3
11
-
4
x
X
x
X
X
X
X
X
x
x
1 / E-5.3
x
X
YOUNG ADULTS
YOUTH PROGRAM
OVERRIDE
SWITCH
X
COLLECTIONS
CHILDREN/JUVENILE
DIMMING
X
x
x
x
1 / E-5.3
x
X
X
X
x
112
CIRCULATION
114
WORKROOM
X
X
115
BRANCH MGR.
X
X
x
x
x
PROGRAM DIM FIXTURES "P" TO 75% OF THEIR CAPACITY.
SYMBOL
OS
9
5
1 / E-5.3
X
1 / E-5.3
8
X
MANUF.
2
x
OS
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
DS
S
9
X
1 / E-5.3
5
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
X
1 / E-5.3
5
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
MEN
X
X
1 / E-5.3
7
117
WOMEN
X
X
1 / E-5.3
7
118
CUSTODIAL
X
MANUF.
2
S
MOUNTING
FINISH
DESCRIPTION
WSD PDT SA __ 30M
WALL ON 2" x 4"
JUNCTION BOX
ARCHITECT
TO SELECT
USE IN ALL OTHER SPACES WHERE NOTED. "VACANCY"
WALL SWITCH WITH DUAL TECHNOLOGY OCCUPANCY
SENSING. PROGRAM OCCUPANCY SENSING FOR 20 MINUTE
SHUT-OFF AFTER OCCUPANT EXIT.
WSD PDT 2P FAN __
WALL ON 2" x 4"
JUNCTION BOX
ARCHITECT
TO SELECT
USE IN RESTROOMS. DUAL TECHNOLOGY WALL SWITCH
OCCUPANCY SENSOR WITH DUAL RELAY FOR LIGHTS AND
FAN.
nWSX PDT LV DX __
WALL ON 2" x 4"
JUNCTION BOX
ARCHITECT
TO SELECT
nLIGHT ENABLED WALL SWITCH, 0-10V DIMMING WITH DUAL
TECHNOLOGY OCCUPANCY SENSOR AND INTEGRATED
PHOTO CONTROL.
nPODM DX __
WALL ON 2" x 4"
JUNCTION BOX
ARCHITECT
TO SELECT
nLIGHT ENABLED SINGLE CHANNEL WALL SWITCH. ON/OFF
AND RAISE/LOWER DIMMING CONTROL .
nPODM 2SB DX __
WALL ON 2" x 4"
JUNCTION BOX
ARCHITECT
TO SELECT
nLIGHT ENABLED 2 SCENE WALL SWITCH WITH ON/OFF,
RAISE/LOWER CONTROL.
nPODM __
WALL ON 2" x 4"
JUNCTION BOX
ARCHITECT
TO SELECT
nLIGHT ENABLED SINGLE CHANNEL WALL SWITCH.
nPODM 4S DX __
WALL ON 2" x 4"
JUNCTION BOX
ARCHITECT
TO SELECT
nLIGHT ENABLED FOUR CHANNEL WALL SWITCH. ON/OFF
AND RAISE/LOWER DIMMING CONTROL .
nPP16 D SA
4x4 GANG BOX
ABOVE
ACCESSIBLE
CEILING SPACE
STANDARD
nLIGHT ENABLED POWER/RELAY PACK WITH "MANUAL ON"
AND 0-10V DIMMING CAPABILITY.
nPP16 D ER SA
4x4 GANG BOX
ABOVE
ACCESSIBLE
CEILING SPACE
STANDARD
nLIGHT ENABLED EMERGENCY POWER/RELAY PACK WITH
"MANUAL ON" AND 0-10V DIMMING CAPABILITY.
nCM PDT 9 RJB
CEILING, 3.5"
OCTAGONAL BOX
MATTE
WHITE
nLIGHT ENABLED CEILING MOUNT OCCUPANCY SENSOR.
nCM 6 RJB
CEILING, 3.5"
OCTAGONAL BOX
MATTE
WHITE
nLIGHT ENABLED HIGH MOUNT OCCUPANCY SENSOR.
nWV PDT 16 KIT
CEILING
STANDARD
WHITE
nLIGHT ENABLED CORNER MOUNT DUAL TECHNOLOGY
OCCUPANCY SENSOR. ORDER WITH CEILING MOUNT "KIT".
nHW 13 WV BR
WALL @ 7' A.F.F.
STANDARD
WHITE
nLIGHT ENABLED HALLWAY OCCUPANCY SENSOR. ORDER
WITH MOUNTING BRACKET KIT "WB BR".
nGWY2 GFX
WALL MOUNT ON
SINGLE GANG
BOX @ 5' A.F.F.
STANDARD
nLIGHT GRAPHIC TOUCH SCREEN.
nECY 24 BAC, nECY
ENC
WALL MOUNT @
5' A.F.F.
STANDARD
nLIGHT ECLYPSE IP AND BUILDING MANAGEMENT
INTERFACE WITH BACnet INTEGRATION CAPABILITY. ORDER
WITH NEMA 1 ENCLOSURE AND INTEGRATED POWER
SUPPLY.
nBRG KIT
WALL MOUNT ON
SINGLE GANG
BOX @ 5' A.F.F.
STANDARD
8 PORT BRIDGE.
OR EQUAL
SENSOR SWITCH
OR EQUAL
nLIGHT
OR EQUAL
OR EQUAL
nLIGHT
DC2
S
OR EQUAL
nLIGHT
C1
S
OR EQUAL
nLIGHT
DC4
X
CATALOG NO.
SENSOR SWITCH
nLIGHT
DC1
1 / E-5.3
116
MANUFACTURER
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
9
5
OR EQUAL
nLIGHT
119
STAFF TOILET
X
121
BOOK MOBILE
X
122
BM OFFICE
X
123
CORRIDOR
124
BOILER
x
125
STORAGE
X
X
X
CORRIDOR
202
UTILITY
203
203A
X
STORAGE
X
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
X
1 / E-5.3
5
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
X
1 / E-5.3
7
-
4
1 / E-5.3
2
x
X
X
X
X
X
1 / E-5.2
7
X
1 / E-5.2
5
X
1 / E-5.2
5
X
MANUF.
2
EM
R
OS
OS
HM
6
X
X
2
X
x
MEETING RM A
1 / E-5.3
x
EXTERIOR LIGHTING
201
2
x
X
R
MANUF.
X
OS
OS
OR EQUAL
nLIGHT
OR EQUAL
nLIGHT
OR EQUAL
nLIGHT
OR EQUAL
nLIGHT
OR EQUAL
nLIGHT
OR EQUAL
nLIGHT
nGWY2
OR EQUAL
204
MEETING RM B
X
X
X
X
X
1 / E-5.2
5
nLIGHT
205
STUDY
X
X
X
1 / E-5.2
5
nECY
OR EQUAL
206
CATER
X
X
X
1 / E-5.2
5
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
nLIGHT
207
MTG. STORAGE
X
X
1 / E-5.2
2
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
nBRG
OR EQUAL
208
STUDY
X
X
X
1 / E-5.2
5
nLIGHT
209
AV-STACKS
X
X
X
X
X
1 / E-5.2
5
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
OR EQUAL
210
DIRECTOR
X
X
X
1 / E-5.2
5
211
BOOKEEPER
X
X
X
1 / E-5.2
5
212
VESTIBULE
X
1 / E-5.2
7
213
RESEARCH
X
X
X
X
1 / E-5.2
5
214
COMPUTER LAB
X
X
X
X
1 / E-5.2
10
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
215
MAKER
X
X
X
X
1 / E-5.2
5
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
216
WOMENS
X
X
1 / E-5.2
7
217
MENS
X
X
1 / E-5.2
7
218
FAMILY
X
X
MANUF.
2
219
STAFF TOILET
X
X
MANUF.
2
220
TECH LAB
X
X
1 / E-5.2
5
221
MDF
X
X
1 / E-5.2
2
222
MECH/ELECT
x
-
4
223
BREAKROOM
X
X
1 / E-5.2
5
224
FILES
X
X
MANUF.
2
225
CORRIDOR
X
1 / E-5.2
7
X
X
x
X
X
03/01/2018
LIGHTING CONTROLS SCHEDULE
RR
x
X
1 / E-5.3
NOTES
SENSORVIEW
SOFTWARE WITH
nFLOORPLAN
OPTION
-
-
SHALL BE INSTALLED ON CFO'S COMPUTER AND
PROGRAMMED AS PART OF THE COMMISSIONING
PACKAGE. ENGINEER SHALL PROVIDE FLOOR PLANS UPON
REQUEST FOR INTEGRATION WITH "nFLOORPLAN" OPTION.
PROGRAM WALL BOX SWITCHES FOR 3-WAY OPERATION.
SEQUENCE OF OPERATIONS
1. MANUAL ON: Lights must be turned on manually at any one of the SC1 switches located at "Exit Access Rm 115", Elevator Lobby Annex #1 or "Stair Hall Rm 200". TIME CLOCK OFF: Owner shall determine programmed "OFF" time for all lights to turn off. OVERIDE SWITCH: Before Time Clock OFF, fixtures shall blink twice giving any
remaining occupants a 20 minute warning that lights will be turned off. Occupant(s) may depress the "ON" button of any SC1 switch mentioned earlier and system will program to run an additional 2 hours, blink twice again before turn off. DIMMING: Fixtures which have dimming capability shall be programmed dimmed to 80% of
their capacity. This shall be considered "FULL ON" and shall be the level all lights perform to at initial on. MANUAL OFF: SC1 switches shall be programmed to turn all lights off if the off button is selected.
2. MANUAL ON: Occupant enters turns lights on manually at wall switch. OCCUPANCY SENSOR OFF: All lights automatically shut off 20 minutes after all occupants exit.
3. MANUAL ON: Occupant enters turns lights on manually at wall switch. OCCUPANCY SENSOR OFF: All lights automatically shut off 20 minutes after all occupants exit. DIMMING: Occupant can manually dim lights to desired level at wall switch. PHOTOCONTROL DIMMING: Lights automatically dim when ambient reaches 50 fc.
4. MANUAL ON/OFF: Standard wall switch.
5. MANUAL ON: Occupant enters turns lights on manually at wall switch. OCCUPANCY SENSOR OFF: All lights automatically shut off 20 minutes after all occupants exit. DIMMING: Occupant can manually dim lights to desired level at wall switch.
6. TIME CLOCK ON/OFF: U.O.N., Lights shall be programmed to operate at astronomic Dusk to Dawn ON/OFF Control.
7. OCCUPANCY SENSOR ON: Occupant enters lights turn on automatically. OCCUPANCY SENSOR OFF: All lights automatically shut off 20 minutes after all occupants exit.
8. OCCUPANCY SENSOR ON: Occupant enters lights turn on automatically. OCCUPANCY SENSOR OFF: All lights automatically dim to 30% 20 minutes after all occupants exit. OVERIDE SWITCH: Before Time Clock OFF cycles, fixtures shall blink twice giving any remaining occupants a 20 minute warning that lights will be turned off.
Occupant(s) may depress the "ON" button of any SC1 switch mentioned earlier and system will program to run an additional 2 hours, blink twice again before turn off.
9. TIME CLOCK ON: Owner shall determine programmed "ON" time for all lights to turn on. TIME CLOCK OFF: Owner shall determine programmed "OFF" time for all lights to turn off. OVERIDE SWITCH: Before Time Clock OFF, fixtures shall blink twice giving any remaining occupants a 20 minute warning that lights will be turned off.
Occupant(s) may depress the "ON" button of any SC1 switch mentioned earlier and system will program to run an additional 2 hours, blink twice again before turn off. DIMMING: Fixtures which have dimming capability shall be programmed dimmed to 80% of their capacity. This shall be considered "FULL ON" and shall be the level all lights
perform to at initial on. MANUAL OFF: SC1 switches shall be programmed to turn all lights off if the off button is selected. Zone controlled dimming from wall switch SDC4. "A" fixtures in zones 2, 4, 5 & 6 shall be control dimmed by button 1. "E" fixtures shall be control dimmed by button 2. "A" fixtures in zone 1 shall be control dimmed by button 3
and "N1" fixtures shall be control dimmed by button 4.
10. MANUAL ON: Occupant enters turns all lights on manually at wall switch. OCCUPANCY SENSOR OFF: When the partition wall is used (dividing the rooms), lights in particular partitioned automatically shut off 20 minutes after all occupants exit the space. DIMMING: Occupant can manually dim all lights to desired level at either wall
switch.
11. OCCUPANCY SENSOR ON: Occupant enters lights turn on automatically. OCCUPANCY SENSOR OFF: All lights automatically dim to 30% 20 minutes after all occupants exit.
ELECTRICAL SCHEDULES
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-5.4
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
PANEL
MDP
PANEL
RA
VOLTAGE (L-N):
120
ENCLOSURE TYPE:
NEMA 1
VOLTAGE (L-N):
120
ENCLOSURE TYPE:
NEMA 1
VOLTAGE (L-L):
VOLTAGE (L-L):
PHASES, WIRES:
1600 A
MINIMUM BUS CAPACITY (A):
225 A
MOUNTING:
AIC RATING (A):
NOTES:
SURFACE
22000
208
3ɸ4W
MINIMUM BUS CAPACITY (A):
MOUNTING:
AIC RATING (A):
NOTES:
SURFACE
PHASES, WIRES:
208
3ɸ4W
MAIN O.C. DEVICE (A):
1600 A
MAIN O.C. DEVICE (A):
MLO
CKT NO
1,3,5
1,3,5
1,3,5
7,9,11
7,9,11
7,9,11
13,15,17
13,15,17
13,15,17
19,21,23
19,21,23
19,21,23
DESCRIPTION
PANEL EE
PANEL EE
PANEL EE
PANEL HP
PANEL HP
PANEL HP
PANEL RA
PANEL RA
PANEL RA
PANEL RC
PANEL RC
PANEL RC
TRIP
AMPS
POLE
400
400
400
600
600
600
225
225
225
225
225
225
3
3
3
3
3
3
3
3
3
3
3
3
----
PHASE LOADS (VA)
A
27048
B
C
4577
29103
5142
27919
61641
5232
4233
62331
7971
60891
10860
3760
8970
14804
10239
14542
9875
8623
7552
8541
6665
7555
6660
CONNECTED LOAD PHASE TOTALS (VA)
134756
144796
CONNECTED LOAD
(KVA)
TRIP
AMPS
3
3
3
3
3
3
3
3
3
3
3
3
150
150
150
150
150
150
225
225
225
225
225
225
DESCRIPTION
PANEL GP
PANEL GP
PANEL GP
PANEL LS
PANEL LS
PANEL LS
PANEL RB
PANEL RB
PANEL RB
PANEL RD
PANEL RD
PANEL RD
CKT NO
CKT NO
2,4,6
2,4,6
2,4,6
8,10,12
8,10,12
8,10,12
14,16,18
14,16,18
14,16,18
20,22,24
20,22,24
20,22,24
1
3
5
7
9
11
13
15
17
19
21
23,25
23,25
27
29
31
33
35
37
39
41
135182
DEMAND FACTOR
DEMAND LOAD (KVA)
414.3
1149.9
TOTAL:
LOAD (AMPS):
POLE
373.7
1037.4
DESCRIPTION
TRIP
AMPS
POLE
20
20
20
20
20
20
20
20
20
20
20
30
30
20
20
20
20
20
20
20
20
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
REFRIG. RECPT. (GFI BREAKER)
RECPT.
RECPT.
RECPT.
RECPT.
LIGHTING
WASHER RECPT.
RECPT.
RECPT.
LIGHTING
RECPT.
DRYER RECPT.
DRYER RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
SPARE
SPARE
SPARE
PHASE LOADS (VA)
A
840
B
HP
VOLTAGE (L-N):
120
ENCLOSURE TYPE:
NEMA 1
VOLTAGE (L-L):
208
3ɸ4W
MINIMUM BUS CAPACITY (A):
600 A
MOUNTING:
AIC RATING (A):
NOTES:
SURFACE
PHASES, WIRES:
1296
1080
MAIN O.C. DEVICE (A):
MLO
CKT NO
1,3,5
1,3,5
1,3,5
7,9,11
7,9,11
7,9,11
13,15
13,15
17,19
17,19
21
23
25,27,29
25,27,29
25,27,29
31
33
35
37
39
41
DESCRIPTION
CU-1A
CU-1A
CU-1A
AHU-1
AHU-1
AHU-1
OU-2B
OU-2B
IU-2B
IU-2B
B-1B (SHUNT TRIP BREAKER)
BP-1B
P-1B
P-1B
P-1B
SPARE
ESTOP (PROVIDE WITH HANDLE LOCK)
SPARE
SPARE
SPARE
SPARE
TRIP
AMPS
POLE
225
225
225
100
100
100
20
20
20
20
15
15
15
15
15
20
15
20
20
20
20
3
3
3
3
3
3
2
2
2
2
1
1
3
3
3
1
1
1
1
1
1
23501
B
C
23501
23501
23501
23501
10472
23501
0
10472
0
10472
0
0
0
0
960
0
0
960
1440
1440
0
0
461
461
461
461
461
461
0
0
270
0
1535
0
0
1535
1535
0
0
0
CONNECTED LOAD PHASE TOTALS (VA)
61641
62331
CONNECTED LOAD
(KVA)
1028
760
0
POLE
TRIP
AMPS
3
3
3
2
2
2
2
1
1
1
1
3
3
3
1
1
3
3
3
1
1
225
225
225
20
20
20
20
15
15
15
15
15
15
15
20
15
25
25
25
20
20
120
ENCLOSURE TYPE:
NEMA 1
VOLTAGE (L-L):
MINIMUM BUS CAPACITY (A):
150 A
MOUNTING:
AIC RATING (A):
NOTES:
SURFACE
PHASES, WIRES:
208
3ɸ4W
MAIN O.C. DEVICE (A):
150 A
TRIP
AMPS
POLE
1
GENERATOR
20
1
3
FACP
20
1
DEMARC BOARD RECEPT.
AREA OF REFUGE RECPT.
RACK UPS RECEPT.
RACK UPS RECEPT.
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
LIGHTING
LIGHTING
SPARE
20
20
30
30
20
20
20
20
20
20
20
20
20
1
1
1
1
1
1
1
1
1
1
1
1
1
5
7
9
11
13
15
17
19
21
23
25
27
29
A
B
468
C
0
960
0
2800
0
0
0
0
0
0
CONNECTED LOAD PHASE TOTALS (VA)
0
2800
2800
0
2800
0
0
0
0
0
0
953
0
0
1052
851
4233
7971
3760
CONNECTED LOAD
(KVA)
DEMAND FACTOR
DEMAND LOAD (KVA)
15.5
43.0
TOTAL:
LOAD (AMPS):
953
TRIP
AMPS
1
20
1
20
1
1
1
1
1
1
1
1
1
1
1
1
1
20
30
30
20
20
20
20
20
20
20
20
20
20
1080
1500
NEMA 1
VOLTAGE (L-L):
MINIMUM BUS CAPACITY (A):
400 A
MOUNTING:
AIC RATING (A):
NOTES:
SURFACE
PHASES, WIRES:
208
3ɸ4W
MAIN O.C. DEVICE (A):
400 A
1,3,5
1,3,5
ELEVATOR MTR
ELEVATOR MTR
350
350
3
3
1,3,5
ELEVATOR MTR
350
3
7
9,11
9,11
13
15
17
LIGHTING
OU-1
OU-1
SPARE
SPARE
SPARE
20
15
15
20
20
20
1
2
2
1
1
1
A
720
720
B
26660
20
0
180
1259
1164
1259
0
0
0
0
0
CONNECTED LOAD PHASE TOTALS (VA)
27048
CONNECTED LOAD
(KVA)
TOTAL:
LOAD (AMPS):
C
26660
0
84.1
233.4
720
720
1080
300
720
720
720
0
540
0
0
0
0
CONNECTED LOAD PHASE TOTALS (VA)
0
14804
14542
DEMAND FACTOR
DEMAND LOAD (KVA)
2
4
6
8
10
12
14
16
18
20
22,24
22,24
26
28
30
32
34
36
38
40
42
RECPT.
RECEPT.
RECEPT.
LIGHTING
RECPT.
RECPT.
LIGHTING
LIGHTING
RANGE RECPT.
RANGE RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
PROJECTOR SCREEN
SPARE
SPARE
SPARE
34.4 KVA
30.4 KVA
DEMAND LOAD
SPARE CAPACITY
34.4
95.6
RB
VOLTAGE (L-N):
120
ENCLOSURE TYPE:
NEMA 1
VOLTAGE (L-L):
MINIMUM BUS CAPACITY (A):
225 A
MOUNTING:
AIC RATING (A):
NOTES:
SURFACE
PHASES, WIRES:
208
3ɸ4W
MAIN O.C. DEVICE (A):
MLO
CKT NO
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
DESCRIPTION
LIGHTING
SPARE
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
DISH WASHER (GFI BREAKER)
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
BOOK MOBILE 121 DOOR MTRS
LIGHTING
SPARE
SPARE
SPARE
TRIP
AMPS
POLE
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
22000
----
PHASE LOADS (VA)
A
750
B
C
720
0
360
1080
720
540
720
360
1080
540
720
1080
720
1004
720
1080
900
1080
840
1500
720
720
720
1080
841
720
762
0
1080
720
720
1185
360
850
0
840
0
0
0
0
CONNECTED LOAD PHASE TOTALS (VA)
0
8970
10239
8623
CONNECTED LOAD
(KVA)
DEMAND FACTOR
DEMAND LOAD (KVA)
27.8
77.3
POLE
TRIP
AMPS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
15
20
20
20
20
DESCRIPTION
CKT NO
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
EWC RECEPT. (GFI BREAKER)
RECPT.
RECPT.
RECPT.
REFRIG. RECPT. (GFI BREAKER)
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
ICE MAKER (GFI BREAKER)
SPARE
SPARE
SPARE
SPARE
DEMAND LOAD
SPARE CAPACITY
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
21.8 KVA
43.1 KVA
21.8
60.5
GENERATOR
SPRINKLER PREACTION PNL (PROVIDE
WITH HANDLE LOCK)
CKT NO
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
SPARE
RACK UPS RECEPT.
RACK UPS RECEPT.
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
LIGHTING
SPARE
14.9 KVA
39.1 KVA
22000
180
28
4500
720
RECPT.
DISHWASHER (GFI BREAKER)
----
PHASE LOADS (VA)
26660
1500
4500
20
20
20
20
20
20
20
20
20
20
50
50
20
20
20
20
20
20
20
20
20
03/01/2018
CKT NO
EE
ENCLOSURE TYPE:
POLE
186.0 KVA
30.1 KVA
DESCRIPTION
DEMAND LOAD
SPARE CAPACITY
120
TRIP
AMPS
1113
948
PANEL
TOTAL:
LOAD (AMPS):
POLE
VOLTAGE (L-N):
DESCRIPTION
720
720
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
DESCRIPTION
14.9
41.3
PANEL
CKT NO
1123
TRIP
AMPS
----
0
480
BP-1A
P-1A
P-1A
P-1A
SPARE
CP-1
REF-1
REF-1
REF-1
SPARE
SPARE
2,4,6
2,4,6
2,4,6
8,10
8,10
12,14
12,14
16
18
20
22
24,26,28
24,26,28
24,26,28
30
32
34,36,38
34,36,38
34,36,38
40
42
22000
PHASE LOADS (VA)
0
CU-1B
CU-1B
CU-1B
OU-2A
OU-2A
IU-2A
IU-2A
WH-1
WH-2
B-1A (SHUNT TRIP BREAKER)
LS
VOLTAGE (L-N):
DESCRIPTION
606
1080
40.2
111.6
CKT NO
186.0
516.3
PANEL
CKT NO
DESCRIPTION
DEMAND LOAD
SPARE CAPACITY
DEMAND LOAD (KVA)
184.9
513.1
TOTAL:
LOAD (AMPS):
1080
900
1080
TOTAL:
LOAD (AMPS):
60891
DEMAND FACTOR
1080
POLE
----
PHASE LOADS (VA)
A
1500
720
CONNECTED LOAD
(KVA)
22000
C
819
10860
PANEL
22000
----
0
29103
27919
DEMAND FACTOR
DEMAND LOAD (KVA)
POLE
TRIP
AMPS
1
1
20
20
1
20
1
1
1
1
1
1
20
20
20
20
20
20
DESCRIPTION
CKT NO
SHAFT PIT RECEPT
SHAFT PIT LIGHTING
ELEV. CAR LGTS, CNTRL PWR, VENT. (with
Lockout)
2
4
8
10
12
14
16
18
RECEPTACLE
SUMP PUMP RECEPT
SPARE
SPARE
SPARE
SPARE
DEMAND LOAD
SPARE CAPACITY
6
84.1 KVA
60.0 KVA
84.1
233.4
ELECTRICAL SCHEDULES
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-5.5
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
PANEL
RC
VOLTAGE (L-N):
120
ENCLOSURE TYPE:
NEMA 1
VOLTAGE (L-L):
208
3ɸ4W
MINIMUM BUS CAPACITY (A):
225 A
MOUNTING:
AIC RATING (A):
NOTES:
SURFACE
PHASES, WIRES:
MAIN O.C. DEVICE (A):
MLO
CKT NO
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
DESCRIPTION
TRIP
AMPS
POLE
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
REFRIG. RECEPT. (GFI BREAKER)
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
SPARE
SPARE
SPARE
SPARE
22000
----
PHASE LOADS (VA)
A
900
B
C
900
931
360
1080
825
360
1080
900
720
720
720
720
720
720
360
720
540
720
0
0
0
CONNECTED LOAD PHASE TOTALS (VA)
0
1080
1080
900
1080
720
540
720
540
720
950
720
720
590
720
0
0
0
0
0
9875
8541
6660
CONNECTED LOAD
(KVA)
DEMAND FACTOR
DEMAND LOAD (KVA)
TOTAL:
LOAD (AMPS):
25.1
69.6
POLE
TRIP
AMPS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
120
ENCLOSURE TYPE:
NEMA 1
208
3ɸ4W
MINIMUM BUS CAPACITY (A):
225 A
MOUNTING:
AIC RATING (A):
NOTES:
SURFACE
PHASES, WIRES:
MAIN O.C. DEVICE (A):
MLO
1
3
5
7
9
11
13
15
17
19
21
23,25
23,25
27
29
31
33
35
37
39
41
POLE
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
LIGHTING
LIGHTING
LIGHTING
LIGHTING
LIGHTING
LIGHTING
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
A
----
B
C
900
720
720
720
900
1080
1080
0
1159
1186
350
1800
0
0
0
0
0
CONNECTED LOAD PHASE TOTALS (VA)
0
720
1080
230
720
1077
1130
1161
770
1174
908
350
617
630
0
0
0
0
0
0
0
0
0
7552
0
6665
CONNECTED LOAD
(KVA)
POLE
TRIP
AMPS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
20
20
20
20
20
20
20
20
20
20
20
30
20
20
20
20
20
20
20
20
20
DEMAND FACTOR
DEMAND LOAD
SPARE CAPACITY
DEMAND LOAD (KVA)
120
ENCLOSURE TYPE:
NEMA 1
VOLTAGE (L-L):
208
3ɸ4W
MINIMUM BUS CAPACITY (A):
150 A
MOUNTING:
AIC RATING (A):
NOTES:
SURFACE
PHASES, WIRES:
MAIN O.C. DEVICE (A):
150 A
1
3
5
7
9,11
9,11
13,15
13,15
17
19
21
23
25
27
29
TECH LAB 220 RECPT.
TECH LAB 220 RECPT.
CIRCULATION CNTR RECPT.
CIRCULATION CNTR RECPT.
OU-2B
OU-2B
IU-2B
IU-2B
RECEPT.
RECEPT.
SPARE
SPARE
SPARE
SPARE
SPARE
TRIP
AMPS
POLE
20
20
20
20
20
20
15
15
20
20
20
20
20
20
20
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1
A
B
720
C
720
720
360
1716
1716
360
360
0
0
0
CONNECTED LOAD PHASE TOTALS (VA)
0
707
1716
135
1716
135
135
360
135
1080
0
0
0
0
0
4577
CONNECTED LOAD
(KVA)
TOTAL:
LOAD (AMPS):
----
720
720
15.0
41.5
24.4 KVA
40.5 KVA
22000
PHASE LOADS (VA)
720
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
GP
VOLTAGE (L-N):
DESCRIPTION
RECPT.
RECPT.
RECPT.
RECPT.
RECPT.
VAV CONTROL TRANSFORMERS
LIGHTING
LIGHTING
LIGHTING
LIGHTING
LIGHTING
DIGITAL SIGN
LIGHTING
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
CKT NO
24.4
67.7
PANEL
CKT NO
DESCRIPTION
7555
21.8
60.4
TOTAL:
LOAD (AMPS):
17.6 KVA
47.3 KVA
22000
PHASE LOADS (VA)
590
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
RD
VOLTAGE (L-L):
TRIP
AMPS
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
RECEPT.
SPARE
SPARE
SPARE
SPARE
SPARE
DEMAND LOAD
SPARE CAPACITY
VOLTAGE (L-N):
DESCRIPTION
RECEPT.
RECEPT.
EWC RECEPT. (GFI BREAKER)
03/01/2018
CKT NO
17.6
48.7
PANEL
CKT NO
DESCRIPTION
0
5142
5232
DEMAND FACTOR
DEMAND LOAD (KVA)
POLE
TRIP
AMPS
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1
20
20
20
20
20
20
15
15
20
20
20
20
20
20
20
DESCRIPTION
TECH LAB 220 RECPT.
A/V STACKS
CIRCULATION CNTR RECPT.
LIGHTING
OU-2A
OU-2A
IU-2B
IU-2B
RECEPT.
RECEPT.
SPARE
SPARE
SPARE
SPARE
SPARE
DEMAND LOAD
SPARE CAPACITY
CKT NO
2
4
6
8
10,12
10,12
14,16
14,16
18
20
22
24
26
28
30
15.1 KVA
38.9 KVA
15.1
42.0
ELECTRICAL SCHEDULES
MARCUM
ENGINEERING, LLC
500 SOUTH 17th STREET - PADUCAH, KENTUCKY 42002
PHONE - 270.444.9274
WWW.MARCUMENGINEERING.NET
E-5.6
CMS ARCHITECTS
P.O. BOX 570 Paducah, KY 42002
Ph: 270-527-5805 Fax: 270-527-9995
cms-architects.com
DATE
3/1/2018
COPYRIGHT ©, 2018 - MARCUM ENGINEERING, LLC
MARSHALL COUNTY PUBLIC LIBRARY @ BENTON
Project No.
16626
Download PDF
Similar pages