General Installation Instructions

General Installation Instructions
LED
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards,
please read all warnings and instructions included with and on the luminaire box and all luminaire labels.
• Before installing, servicing or performing routine maintenance upon this equipment, follow these general precautions.
• Installation and service of luminaires should be performed by a qualified licensed electrician.
• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards
involved. Regular luminaire maintenance programs are recommended.
• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and
minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, nonabrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/
lens and clean in above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during
transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in
connection with installation, operation or maintenance. Should further information be desired or should particular problems arise which
are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc., a parent
company of Peerless Lighting.
WARNING
RISK OF ELECTRIC SHOCK
4Disconnect or turn off power before installation or
servicing.
4Verify that supply voltage is correct by comparing it with
the luminaire label information.
4Make all electrical and grounded connections in
accordance with the National Electrical Code (NEC) and
any applicable local code requirements.
4All wiring connections should be capped with UL approved
recognized wire connectors.
4To prevent luminaire row from over-­current: By adding
the input current of each luminaire section marked on
the luminaire, the total current per power feed must not
exceed the maximum line wire amperage marked on the
luminaire and the power feed cord/wire amperage rating
whichever the least.
WARNING
RISK OF BURN
4Allow lamp/luminaire to cool before handling. Do not
touch enclosure or light source.
4Do not exceed maximum wattage marked on luminaire
label.
4Follow all manufacturer’s warnings, recommendations and
restrictions for: driver type, burning position, mounting
locations/methods, replacement and recycling.
Part Number: PIN004102 Description: “INSTR, IMPORTANT SAFETY LED” Revision: C Effective Date: 07/2012 ECO3665 page 1 of 2
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2014 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Limited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
General Installation Instructions LED A
General Installation Instructions
LED
CAUTION
RISK OF INJURY
CAUTION
RISK OF FIRE
4Wear gloves and safety glasses at all times when removing
luminaire from carton, installing, servicing or performing
maintenance.
4Avoid direct eye exposure to the light source while it is on.
4Keep combustible and other materials that can burn away
from lamp/lens.
4Do not operate in close proximity to persons, combustible
materials or substances affected by heat or drying.
CAUTION
RISK OF PRODUCT DAMAGE
4Never connect components under load.
4Do not mount or support these luminaires in a manner that can cut the outer jacket or damage wire insulation.
4Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer packs, occupancy
sensors, timing devices, or other related control devices. LED luminaires must be powered directly off a switched circuit.
4Unless individual product specifications deem otherwise: Do not restrict luminaire ventilation. Allow for some volume of airspace
around luminaire. Avoid covering LED luminaires with insulation, foam or other material that will prevent convection or conduction
cooling.
4Unless individual product specifications deem otherwise: Do not exceed luminaire’s maximum ambient temperature.
4Only use luminaire in its intended location.
4LED products are polarity sensitive. Ensure proper polarity before installation.
4Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or
servicing of the unit.
4Do not touch individual electrical components as this can cause ESD, shorten lamp life or alter performance.
4Some components inside the luminaire may not be serviceable. In the unlikely event your unit may require service, stop using the
unit immediately and contact a Peerless Lighting representative for assistance.
4Always read the fixtures complete installation instructions prior to installation for any additional luminaire specific warnings.
SAVE THESE INSTALLATION INSTRUCTIONS
Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory statements.
Failure to follow any of these instructions could void product warranties.
For a complete listing of product Terms and Conditions, please visit PeerlessLighting.com.
Peerless Lighting, an Acuity Brands Company, assumes no responsibility for claims arising out of improper or careless installation or handling of its products.
Part Number: PIN004102 Description: “INSTR, IMPORTANT SAFETY LED” Revision: C Effective Date: 07/2012 ECO3665 page 2 of 2
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2014 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Limited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
General Installation Instructions LED
B
General Installation Instructions WARNING
To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other
hazards:
• Service of the equipment must be performed by qualified service personnel.
• Installation and maintenance must be performed by a person familiar with the construction and operation of this product
and any hazards involved. All applicable codes and ordinances must be followed.
• Read this document before installing, servicing or maintaining this equipment or installing a lamp. These instructions do
not cover all installation, service and maintenance situations. If your situation is not covered, or, if you do not
understand these instructions or additional information is required, contact Peerless Lighting or your local Peerless
Lighting distributor.
• Read and follow all warnings and instructions provided by the lamp manufacturer.
WARNING
Before installing, servicing or maintaining this equipment, follow these general precautions. To reduce the risk of
electrocution:
• Make sure the equipment is properly grounded.
• Always de-energize the circuit and/or equipment before connecting to, disconnecting from or servicing the equipment.
To prevent luminaire row from over-current:
• By adding the input current of each luminaire section marked on the luminaire, the total current per power feed must not
exceed the maximum line wire amperage marked on the luminaire and the power feed cord/wire amperage rating
whichever is the least.
To reduce the risk of fire:
• Keep material away that can burn from hot lamp.
• Make sure lamps are correctly installed.
• Use supply conductors with a minimum installation temperature rating as specified on equipment.
To reduce the risk of personal injury from cuts, abrasions or falling parts:
• Wear gloves to prevent cuts or abrasions from sharp edges when removing from carton, handling and maintaining this
equipment.
• Do not use abrasive materials, glass cleaners or other solvents on reflector or lens. These substances may damage
equipment and cause parts to eventually break and fall.
• Do not install a damaged fixture.
CAUTION
Observe lamp manufacturer’s recommendations and restrictions on lamp operation including but not limited to ballast
type, burning position, replacement and cycling. Use only lamps that comply with applicable ANSI standards.
NOTICE: If lamp is marked
it contains mercury. Follow disposal laws. See www.lamprecycle.org
Peerless Lighting, a division of Acuity Brands Lighting, Inc., assumes no responsibility for
claims arising out of improper or careless installation or handling of this product.
SAVE THESE INSTALLATION INSTRUCTIONS
Part Number: PIN004100 Revision: E Effective Date: 07/2012 ECO3665
Bruno Wall T5/T5HO/T8/LED
INSTALLATION INSTRUCTIONS
PIN004301 REV. A 10/13 ECO3706
BRW
These installation instructions are used for installing the following luminaires and kits:
Luminaires
Configuration Kit
Mounting Kit
End Cap Kit
Dust Cover
BRW9L
BRWL CNRI/CNRO/TNN/(SCEP)
BRWLFK/SK
BRW9LEP(SCEP)
BRW9LDU
BRW1/2/3/4/7/9
BRW CNRI/CNRO/TNN/(SCEP)
BRWFK/SK
BRWEP (SCEP)
BRWDU
WARNING: Please read the “important safety instructions” prior to installation of this product. The mounting instructions can be found inside the mounting
kits or downloaded from PeerlessLighting.com.
A) Identification of BRW Luminaire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page1
B) Standard Wall Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
C) Tenon (TNN) Installation for Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 2/3
D) Corner (CNRI/CNRO) Installation for Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
E) Dust Cover (DU) Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
A) Identification of BRM Luminaire
CNRO
(OPTIONAL)
TNN
(OPTIONAL)
CNRI
(OPTIONAL)
TNN SCEP
(SCULPTED END
PLATE OPTIONAL)
TNN
(OPTIONAL)
WALL MUST BE ADEQUATELY REINFORCED AT SUPPORT
LOCATIONS — BY OTHERS — FOR SOUND STRUCTURAL
AND AESTHETIC INSTALLATION OF THIS LUMINAIRE .
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Llimited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
Bruno Wall T5/T5HO/T8/LED
1
Bruno Wall T5/T5HO/T8/LED
PIN004301 REV. A 10/13 ECO3706
BRW
B) Standard Wall Installation
1
Use a laser or snap line to position luminaire
on wall. At power feed location, cut hole in
wall to accommodate 2” horizontal J-box (by
others). Install J-box and pull building power
wires through as shown.
4
Connect power feed wire harness to
luminaire wire harness as shown. Insert
connection back into luminaire.
7
Hang luminaire section on wall bracket as
shown. Check luminaire for level, make
adjustments as necessary.
2
Sandwich J-box cover plate between J-box
and bracket as shown. Install mounting
bracket to wall using ¼” bolts (by others).
5
Discard power feed plug from first luminaire
section and pull power feed wires through
opening as shown.
8
Lock luminaire to wall bracket using (2)
supplied screws per bracket as shown.
3
Install non-power feed wall brackets to wall
along laser/snap line using (2) ¼-20 bolts
per bracket. Use (2) wall brackets for
4’ sections, (3) wall brackets for 8’ sections
and (4) for 12’ sections.
6
Raise first luminaire into position. Connect
building power with luminaire power feed
wires using appropriate connectors (by
others).
9
¼-20 Screw
To add luminaire sections, repeat Step 3.
Next, connect luminaire wire harnesses as
shown. Repeat instructions 7 and 8. Finally,
bolt adjoining luminaire sections together —
with light shield in between—with (2) ¼-20
screws as shown.
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Llimited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
Bruno Wall T5/T5HO/T8/LED
2
Bruno Wall T5/T5HO/T8/LED
PIN004301 REV. A 10/13 ECO3706
BRW
10
To complete installation, install end-caps
with (2) provided # 10 screws as shown.
B) Tenon (TNN) Installation
1
Discard the light shield. Connect luminaire
wires harnesses and secure tenon to
luminaires using #10 screws as shown.
2
A complete tenon installation is shown
above.
3
A complete tenon installation with sculpted
end cap (SCEDP) is show above.
C) Corner (CNRI/CNRO) Installation
1
Discard the light shield. Connect luminaire wires harnesses and secure corner to luminaires
using #10 screws as shown.
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Llimited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
Bruno Wall T5/T5HO/T8/LED
3
Bruno Wall T5/T5HO/T8/LED
PIN003701 REV. A 10/13 ECO3706
BRW
D) Dust Cover (DU) Installation
1
For BRW1/2/3/4/7/9, simply remove the for
re-lamping and cleaning during mainenance
and then restore the part by overlaying it
atop the lamp assembly as shown.
2
For BRW9L, simply remove the dust cover
for cleaning during maintenance and then
restore the part by overlaying it atop the
luminarie as shown.
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Llimited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
Bruno Wall T5/T5HO/T8/LED 4
Download PDF
Similar pages