User Manual
GETTING
STARTED?
EASY.
ZWF 71443W
EN User Manual
Washing Machine
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an
incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future
reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Do not let children play with the appliance.
Children of less than 3 years should be kept away unless
continuously supervised.
Keep all packaging away from children.
Keep all detergents away from children.
Keep children and pets away from the appliance door when it is
open.
If the appliance has a child safety device, we recommend you
activate it.
Cleaning and user maintenance shall not be made by children
without supervision.
GENERAL SAFETY
•
•
•
•
•
2
Do not change the specification of this appliance.
Obey the maximum load volume of 7 kg (refer to the
“Programme chart” chapter).
The operating water pressure (minimum and maximum) must be
between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa).
The ventilation openings in the base (if applicable) must not be
obstructed by a carpet.
The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
•
•
•
•
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
Before maintenance, deactivate the appliance and disconnect
the mains plug from the mains socket.
Do not use water spray and steam to clean the appliance.
Clean the appliance with a moist soft cloth. Only use neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
• Remove all the packaging and the transit bolts.
• Keep the transit bolts. When you move the
appliance again you must block the drum.
• Always be careful when you move the appliance
because it is heavy. Always wear safety gloves.
• Do not install or use a damaged appliance.
• Obey the installation instruction supplied with
the appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C or where it is
exposed to the weather.
• Make sure that the floor where you install the
appliance is flat, stable, heat resistant and clean.
• Make sure that there is air circulation between
the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the carpet.
• Do not install the appliance where the appliance
door can not be fully opened.
ELECTRICAL CONNECTION
• The appliance must be earthed.
• Always use a correctly installed shockproof
socket.
• Make sure that the electrical information on the
rating plate agrees with the power supply. If not,
contact an electrician.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
•
•
•
•
Do not touch the mains cable or the mains plug
with wet hands.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Only for UK and Ireland: The appliance has a 13
amp mains plug. If it is necessary to change the
fuse in the mains plug, use a 13 amp ASTA (BS
1362) fuse.
This appliance complies with the E.E.C.
Directives.
WATER CONNECTION
• Make sure not to cause damage to the water
hoses.
• Before you connect the appliance to new pipes
or pipes not used for a long time, let the water
flow until it is clean.
• The first time you use the appliance, make sure
that there is no leakage.
USE
WARNING! Risk of injury, electrical
shock, fire, burns or damage to the
appliance.
•
•
•
•
•
•
Use this appliance in a household only.
Obey the safety instructions on the detergent
packaging.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Make sure that you remove all metal objects
from the laundry.
Do not put a container to collect possible water
leakage under the appliance. Contact the
Authorised Service Centre to ensure which
accessories can be used.
Do not touch the glass of the door while a
programme operates. The glass can be hot.
3
SERVICE
• To repair the appliance contact an Authorised
Service Centre.
• Use original spare parts only.
•
•
•
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent children and
pets to get closed in the appliance.
DISPOSAL
WARNING! Risk of injury or
suffocation.
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1
2
1 Worktop
2 Detergent dispenser
3
3 Control panel
4 Door handle
5 Rating plate
6 Feet for the appliance level
4
5
6
INSTALLATION ON SUSPENDED FLOORING
Suspended wooden floors are particularly
susceptible to vibration.
To help prevent vibration we recommend you place
a waterproof wood panel, at least 15 mm thick
under the appliance, secured to at least 2 floor
beams with screws, the wood panel must extend
beyond the front feet.
If possible install the appliance in one of the
corners of the room, where the floor is more stable.
CHILD SAFETY
This device prevents children or pets to be closed
in the drum.
4
•
•
Turn the device clockwise, until the groove
is horizontal.
You cannot close the
door.
To close the door,
turn the device anticlockwise until the
groove is vertical.
FIXING PLATE KIT (4055171146)
Available from your authorized dealer.
If you install the appliance on a plinth, secure the
appliance in the fixing plates.
Read carefully the instructions supplied with the
accessory.
EASY START
CONTROL PANEL DESCRIPTION
1
2
3
4
Cottons
Jeans
Cotton ECO
Refresh
20min
Synthetics
90°
1400
60°
40°
Delay Start
900
30°
Delicates
Easy Iron
Wool/
Handwash
Spin
Drain
Dark Garments
Rinse
Mix 20°
700
Temp
10
Spin
Rinse
Hold
9
8
Quick
Extra
Rinse
Start/Pause
7
6
5
1 Programme knob
2 Display
7 Super Quick button (Quick)
8 Rinse Hold button (Rinse Hold)
3 Delay Start button (Delay Start)
4 Door locked indicator
9 Spin reduction button (Spin)
10 Temperature button (Temp)
5 Start/Pause button (Start/Pause)
6 Extra Rinse button (Extra Rinse)
DISPLAY
A
B
The display shows:
C
A) The delay start .
When you press the delay start button, the
display shows the delay start time.
B) The child lock indicator.
The indicator comes on the display when the
related option is set.
C) This area shows:
• The programme time.
• The alarm codes.
If the appliance has a malfunction, the
display shows the alarm codes. Refer to the
chapter 'Troubleshooting' .
•
The display shows the message
for
some seconds if:
– You set a option that is not suitable for
the programme.
– You change the programme while it
operates.
5
PROGRAMME CHART
Programme
Temperature range
Maximum load
Maximum spin
speed
Cotton
90°C - Cold
7 kg
1400 rpm
White cotton and coloured cotton. Normal soil and
light soil.
Cotton
7 kg
1400 rpm
White cotton and colour-fast cotton. Normal soil. The
energy consumption decreases and the time of the washing programme is extended.
Synthetics
60°C - Cold
3 kg
900 rpm
Synthetic items or mixed fabric items. Normal soil.
Delicates
40°C - Cold
3 kg
700 rpm
Delicate fabrics as acrylics, viscose, polyester
items. Normal soil.
Wool/Handwash
40°C - Cold
2 kg
900 rpm
Machine washable wool, hand washable wool and
delicate fabrics with «hand washing» care symbol.2)
Dark Garments
40°C
3 kg
1400 rpm
Cotton items or mixed fabric items in dark colours.
Normal soil.
Mix 20°
20°C
2 kg
900 rpm
Special programme for cotton, synthetic and mixed fabrics
with light soil. Set this programme to decrease the energy
consumption. Make sure that the detergent is for low temperature in order to have good washing results3).
Rinse
7 kg
1400 rpm4)
To rinse and spin the laundry. All fabrics.
Drain
7 kg
To drain the water in the drum. All fabrics.
Spin
7 kg
1400 rpm
To spin the laundry and to drain the water in the drum. All
fabrics.
Easy Iron
60°C - Cold
1 kg
900 rpm
Synthetic items to be gentle washed. Normal and
light soil.5)
Refresh 20min
30°C
1 kg
900 rpm
Synthetic and delicate items. Light soil items or items
to refresh.
Jeans
60°C - Cold
3 kg
900 rpm
Items in denim and jersey. Normal soil.
Eco1)
60°C - 40°C
6
Programme description
(Type of load and soil level)
Programme
Temperature range
30'@ 30°
30°C
Maximum load
Maximum spin
speed
3 kg
700 rpm
Programme description
(Type of load and soil level)
A short cycle for synthetics and delicate items with
light soil level or for items to freshen up.
1) Standard programmes for the Energy Label consumption values. According to regulation
1061/2010, these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme». They are the most efficient programmes in terms of combined energy and
water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the
selected programme.
2) During this cycle the drum rotates slowly to ensure a gentle washing. It can seem that the drum doesn't
rotate or doesn't rotate properly. Consider this as a normal functioning of the appliance.
3) The appliance performs the short heating phase if the water temperature is below 20°C. The appliance
can show the temperature setting as “cold”.
4) The default spin speed is 700 rpm.
5) To reduce the creases of the laundry, this cycle regulates the water temperature and performs a soft
wash and spin phase. The appliance adds some rinses.
Programme options compatibility
Programme
Cotton
Cotton Eco
Synthetics
Spin
Rinse Hold Quick 1) Extra Rinse Delay Start
■
■
■
■
■
■
■
Delicates
■
■
■
■
■
■
■
■
■
■
■
Wool/Handwash
■
■
■
Dark Garments
■
■
■
■
Mix 20°
■
■
■
■
Rinse
■
■
■
■
■
Drain
Spin
■
Easy Iron
■
Refresh 20min
■
Jeans
■
■
■
■
■
■
■
■
7
Programme
Spin
Rinse Hold Quick 1) Extra Rinse Delay Start
■
30'@ 30°
1) When you set the Quick option, we recommend that you decrease the quantity of the laundry. It is possible to keep the full load but the washing results can be unsatisfactory. Recommended load: cotton: 3,5
kg, synthetics and delicates: 1,5 kg.
CONSUMPTION VALUES
The data of this table are approximate. Different causes can change the data: the quantity
and type of laundry, the water and ambient temperature.
At programme start the display shows the duration programme for the maximum load capacity.
During the washing phase the programme duration is automatically calculated and can be
greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton
60°C, maximum load capacity 7 kg, the programme duration exceeds 2 hours; real load 1
kg, the programme duration don’t reach 1 hour).
When the appliance is calculating the real programme duration a dot blinks in the display.
Programmes
Load (kg)
Energy consumption
(kWh)
Water consumption (litre)
Approximate
Remaining
programme
duration (mi- moisture (%)1)
nutes)
Cotton 60 °C
7
1,34
68
157
52
Cotton 40 °C
7
0,78
61
157
52
Synthetics 40 °C
3
0,60
56
103
35
Delicates 40 °C
3
0,55
59
81
35
Wool/Handwash 30
°C 2)
2
0,30
53
57
30
Standard cotton programmes
Standard 60 °C cotton
7
0,92
45
250
52
Standard 60 °C cotton
3,5
0,68
35
204
52
Standard 40 °C cotton
3,5
0,53
36
189
52
1) At the end of spin phase.
2) Not available for some models.
8
Off Mode (W)
0,48
Left On Mode (W)
0,48
The information given in the chart above are in compliance with the EU Commission regulation
1015/2010 implementing directive 2009/125/EC.
OPTIONS
TEMP
With this option you can change the default
temperature.
Indicator
= cold water.
The indicator of the set temperature comes on.
SPIN
With this option you can change the default spin
speed.
The indicator of the set speed comes on.
RINSE HOLD
Set this option to prevent the laundry creases.
The related indicator comes on.
There is water in a drum when the
programme completes. To drain the
water refer to ‘At the end of the
programme’.
QUICK
Press this button to decrease the programme
duration.
Set this option for items with light soil or items to
refresh.
EXTRA RINSE
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to detergents
and in areas where the water is soft.
The related indicator comes on.
DELAY START
With this option you can delay the start of a
programme from 30 minutes to 20 hours.
The display shows the related indicator.
DOOR LOCKED INDICATOR
The indicator
shows when the door can be
opened:
• The indicator is on: the door cannot be opened.
• The indicator flashes: the door is opening in
some minutes.
• The indicator is off: the door can be opened.
SETTINGS
CHILD LOCK
With this option you can prevent that the children
play with the control panel.
• To activate/deactivate this option, press
Temp and Spin at the same time until the
indicator
comes on/goes off.
You can activate this option:
• After you press Start/Pause: the options and the
programme knob are locked.
• Before you press Start/Pause: the appliance
cannot start.
ACOUSTIC SIGNALS
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
press Rinse Hold and Quick at the same time for
6 seconds.
If you deactivate the acoustic signals,
they continue operate when the
appliance has a malfunction.
EXTRA RINSE
With this option you can permanently have an extra
rinse when you set a new programme.
• To activate/deactivate this option touch the
buttons Rinse Hold and Extra Rinse at the
9
same time until the indicator of Extra Rinse
button comes on/goes off.
BEFORE FIRST USE
1. Put a small quantity of detergent in the
compartment for washing phase.
2. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
DAILY USE
WARNING! Refer to Safety chapters.
LOADING THE LAUNDRY
Open the water tap. Connect the mains plug to the
mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
Refer to max. loads indicated in "Programme chart".
4. Close the door.
CAUTION!
Make sure
that no laundry stays between the
seal and the
door. There
is a risk of
water leakage or damage to the
laundry.
USING DETERGENT AND ADDITIVES
1. Measure out the detergent and the fabric
conditioner.
2. Put the detergent
and the fabric conditioner into the compartments.
3. Carefully close the
detergent drawer.
10
DETERGENT COMPARTMENTS
Detergent compartment for
washing phase.
If you use liquid detergent, put it
immediately before you start the
programme.
Compartment for liquid additives
(fabric conditioner, starch).
CAUTION! Do not
exceed the MAX
level.
Flap for powder or liquid detergent.
LIQUID OR POWDER DETERGENT
The default position of
the flap is A (powder deA
tergent).
To use liquid detergent:
1. Remove the drawer.
Push the drawer edge in
the place with the arrow
(PUSH) to remove the
drawer easily.
2. Adjust the flap in position B.
3. Put back the drawer in
the recess.
B
When you use the liquid detergent:
• Do not use gelatinous or thick liquid detergents.
• Do not put more liquid then 120
ml.
• Do not set the delay start.
A
When the flap is in position B and you want to
use powder detergent:
1. Remove the drawer.
2. Adjust the flap in position A.
3. Put back the drawer
in the recess.
SETTING A PROGRAMME
1. Turn the programme knob to switch the
appliance on and set the programme:
• The indicator of the button Start/Pause
flashes.
• The display shows the programme duration.
2. If necessary, change the temperature and the
spin speed or add available options. When you
activate an option, the indicator of the set
option comes on.
.
STARTING A PROGRAMME WITHOUT THE
DELAY START
Press the button Start/Pause.
• The indicator of the button Start/Pause
stops to flash and stays on.
• The programme starts, the door locks, the
indicator
is on.
• The programme time decreases with steps
of one minute.
The drain pump can operate for a
short time at the beginning of the
washing cycle.
1. Press the button Delay Start again and again
until the display shows the delay you want to
set. The delay start indicator comes on.
2. Press the button Start/Pause:
• The door is locked and the indicator
is
on.
• The appliance starts the countdown.
• When the countdown is completed, the
programme starts automatically.
You can cancel or change the set of
the Delay Start option before you
press the button Start/Pause. After
pressing the button Start/Pause you
can only cancel the Delay Start option.
To cancel the Delay Start option:
a. Press the button Start/Pause to set the
appliance to pause. The indicator of button
Start/Pause flashes.
b. Press the button Delay Start until the
display shows .
Press the button Start/Pause again to start
the programme immediately.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before they
operate.
1. Press the button Start/Pause.
The indicator flashes.
2. Change the options.
3. Press the button Start/Pause again.
The programme continues.
CANCELLING A RUNNING PROGRAMME
If you set something incorrect, the
display shows the message
STARTING A PROGRAMME WITH THE DELAY
START OPTION
1. Turn the programme knob to position
to
cancel the programme and to deactivate the
appliance.
2. Turn the programme knob again to activate the
appliance. Now, you can set a new washing
programme.
Before starting the new programme
the appliance could drain the water. In
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
OPENING THE DOOR
While a programme or the Delay Start operates, the
is on.
appliance door is locked. The indicator
11
CAUTION! If the temperature and
level of the water in the drum are too
high and the drum still rotates, you
cannot open the door.
To open the door during the first minutes of the
cycle or when the Delay Start operates:
1. Press the button Start/Pause to pause the
appliance.
2. Wait until the indicator
goes off.
3. You can open the door.
4. Close the door and touch the button Start/
Pause again. The programme (or the Delay
Start) continues.
AT THE END OF THE PROGRAMME
• The appliance stops automatically.
• The acoustic signal operates (if it is activated).
•
•
•
In the display comes on.
The indicator of the button Start/Pause goes off.
The door lock indicator
goes off.
Turn the programme knob to position
to
deactivate the appliance.
• You can open the door.
• Remove the laundry from the appliance. Make
sure that the drum is empty.
• Close the water tap.
• Keep the door and the detergent drawer ajar, to
prevent the mildew and odours.
The washing programme is completed, but
there is water in the drum:
•
The drum turns regularly to prevent the creases
in the laundry.
• The indicator Rinse Hold stays on to remind you
to drain the water.
is on. The indicator
• The door lock indicator
of button Start/Pause is off. The door stays
locked.
• You must drain the water to open the door.
Draining the water:
1. To drain the water.
• Set a Drain or a Spin programme.
• Press the button Start/Pause. The
appliance drains the water and spins.
2. When the programme is completed and the
goes off, you can open
door lock indicator
the door.
3. Turn the programme knob to the position
deactivate the appliance.
to
STAND BY
Some minutes after the end of the washing
programme, if you do not deactivate the appliance,
the energy saving status activates. The energy
saving status decreases the energy consumption
when the appliance is on the standby:
• All indicators and the display go off.
• The indicator of button Start flashes slowly.
Press one of the buttons to deactivate the energy
saving status.
HINTS AND TIPS
THE LAUNDRY LOAD
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on the
laundry care labels.
• Do not wash together white and coloured items.
• Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first times.
• Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn inside out multilayered fabrics, wool and
items with painted illustrations.
• Remove hard stains.
• Wash with a special detergent heavy soil stains.
• Be careful with the curtains. Remove the hooks
or put the curtains in a washing bag or
pillowcase.
12
•
•
Do not wash in the appliance laundry without
hems or with cuts. Use a washing bag to wash
small and/or delicate items (e.g. underwired
bras, belts, tights, etc. ).
A very small load can cause balance problems
with the spin phase. If this occurs, adjust
manually the items in the tub and start the spin
phase again.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you remove these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND ADDITIVES
• Only use detergents and additives specially
made for washing machines:
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (40
°C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special for woollens
only.
• Do not mix different types of detergents.
• To help the environment, do not use more than
the correct quantity of detergent.
• Obey the instructions that you find on the on
packaging of these products.
• Use the correct products for the type and colour
of the fabric, the programme temperature and
the level of soil.
• If your appliance has not the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by the
detergent's manufacturer).
•
•
•
Always start a washing programme with the
maximum load of laundry.
If necessary, use a stain remover when you set a
programme with a low temperature.
To use the correct quantity of the detergent,
check the water hardness of your domestic
system
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To know the water hardness in your area, contact
your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
ECOLOGICAL HINTS
• Set a programme without the prewash phase to
wash laundry with normal soil.
CARE AND CLEANING
WARNING! Refer to Safety chapters.
EXTERNAL CLEANING
Clean the appliance only with soap and warm
water. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special products
for washing machine. Do this separately from the
laundry wash.
MAINTENANCE WASH
With the low temperature programmes it is possible
that some detergent stays in the drum. Make
regularly a maintenance wash. To do this:
• Remove the laundry from the drum.
• Set the cotton programme with the highest
temperature with a small quantity of detergent.
DOOR SEAL
Regularly examine the
seal and remove all objects from the inner part.
Always obey the instructions that you
find on the packaging of the product.
13
CLEANING THE DETERGENT DISPENSER
1
2
3
4
CLEANING THE INLET HOSE AND THE VALVE FILTER
1
1
2
3
4
2
45°
3
20°
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0 °C, remove the
remaining water from the inlet hose and the drain
pump.
Do this procedure also when you want
to do the emergency drain.
1. Disconnect the mains plug from the mains
socket.
2. Remove the water inlet hose.
3. Remove the drain hose from the rear support
and unhook it from sink or spigot.
4. Put the ends of the drain and inlet hose in a
container. Let the water flow out of the hoses.
5. When no more water flows, install the inlet
hose and the drain hose again.
WARNING! Make sure that the
temperature is more than 0 °C before
you use the appliance again. The
manufacturer is not responsible for
damages caused by low temperatures.
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The start of the appliance does not occur or it
stops during operation.
First try to find a solution to the problem (refer to
the table). If not, contact the Authorised Service
Centre.
14
With some problems, the acoustic signals
operate and the display shows an alarm
code:
•
•
- The appliance does not fill with water
properly.
- The appliance does not drain the water.
•
- The appliance door is open or not
closed correctly. Please check the door!
•
- The mains supply is unstable. Wait until
the mains supply is stable.
WARNING! Deactivate the appliance
before you do the checks.
POSSIBLE FAILURES
Problem
The programme does not
start.
Possible solution
•
•
•
•
•
•
The appliance does not fill
with water properly.
•
•
•
•
•
•
•
The appliance does not
drain the water.
•
•
•
•
•
•
The spin phase does not
operate or the washing cycle lasts longer than usually.
•
•
There is water on the floor.
•
•
•
•
You cannot open the appliance door.
•
•
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
Make sure that there is not a damaged fuse in the fuse box.
Make sure that the Start/Pause has been pressed.
If the delay start is set, cancel the setting or wait for the end of
countdown.
Deactivate the Child Lock function if it is on (if available).
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter of the inlet hose and the filter of the valve
are not clogged. Refer to “Care and cleaning”.
Make sure that the inlet hose has no kinks or bends.
Make sure that the connection of the water inlet hose is correct.
Make sure that the drain hose is in the correct position. The hose
may be too low.
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
Make sure that the connection of the drain hose is correct.
Set the drain programme if you set a programme without drain
phase.
Set the drain programme if you set an option which ends with water
in the drum.
If above mentioned solutions do not help, contact the Authorised
Service Centre (as the filter of the drain pump may be clogged).
Set the spin programme.
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
If above mentioned solutions do not help, contact the Authorised
Service Centre (as the filter of the drain pump may be clogged).
Make sure that the couplings of the water hoses are tight and there
is not water leakages.
Make sure that the inlet hose and/or the drain hose have no damages.
Make sure you use the correct detergent and the correct quantity of
it.
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
15
Problem
The appliance makes an
unusual noise.
Possible solution
•
•
•
Make sure the levelling of the appliance is correct. Refer to 'Installation Instruction'.
Make sure that the packaging and/or the transit bolts are removed.
Refer to 'Installation Instruction'.
Add more laundry in the drum. The load may be too small.
The cycle is shorter than
the time displayed.
The appliance calculates a new time according to the laundry load.
See the ‘Consumption Values’ chapter.
The cycle is longer than
the time displayed.
An unbalanced laundry load increases the duration time. This is a normal behaviour of the appliance.
The washing results are
not satisfactory.
•
•
You cannot set an option.
•
•
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you
wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
•
Make sure that you press only the wanted button(s).
After the check, activate the appliance. The
programme continues from the point of interruption.
If the problem occurs again, contact the Authorised
Service Centre.
If the display shows other alarm codes. Deactivate
and activate the appliance. If the problem
continues, contact the Service.
SERVICE
We recommend the use of original spare parts.
When contacting the Authorised Service Centre,
make sure that these data are available. You can
find the information on the rating plate: model
(Mod.), PNC (Prod.No.), Serial number (Ser.No.).
TECHNICAL DATA
Dimension
Width/ Height/ Depth/ Total depth
600 mm/ 850 mm/ 559 mm/ 578 mm
Electrical connection
Voltage
Overall power
Fuse
Frequency
230-240 V
2200 W
13 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
1)
Minimum
Maximum
Cold water
Water supply 2)
Maximum Load
Energy Efficiency Class
16
Cotton
7 kg
A+++
Spin Speed
Maximum
1400 rpm
1) The appliance works correctly if the water pressure is not less than 0.05 MPa (0.5 bar). If you can not
connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your domestic cold water storage system. Make sure not to have more than a distance of 5.02 m (16.5 ft) between the appliance inlet hose and the bottom of the water storage tank.
2) Connect the water inlet hose to a water tap with a 3/4'' thread.
ENVIRONMENT CONCERNS
the symbol with the household waste. Return the
product to your local recycling facility or contact
your municipal office.
Recycle the materials with the symbol
. Put the
packaging in applicable containers to recycle it.
Help protect the environment and human health
and to recycle waste of electrical and electronic
appliances. Do not dispose appliances marked with
17
*
18
19
192965120-A-112015
WWW.ZANUSSI.COM/SHOP
Download PDF
Similar pages