VERAK® EMC / IP
19” Stand Alone Cabinet with EMC and IP65 Rating
www.apw.eu.com
VERAK® EMC / IP
Overview
Material specification
•
•
•
•
•
•
•
Frame: Steel 2.0 mm
Panel mounting angles and reducing channels: Steel 2.0 mm
Panel mount supports: Steel 1.5 mm
Side panels: Steel 1.5 mm
Top cover: Steel 1.2 mm
Doors: Steel 1.5 mm
Glass: Twin glass 3 mm thick with thin wire mesh inside
• VERAK® EMC / IP load capacity: 1.000 Kg
Standards
IEC 60297:
Dimensions of mechanical structures of the
482.6 mm (19”) series
DIN 41494:
Basic specification for the 19” construction
systems
EN 60950:
European safety standard for information
technology equipment
VDE 0100:
Installation and Set up of current systems and
earthing
Colour specification
Standard VERAK® EMC / IP
RAL 7035
Side panels
RAL 7037
Top cover, front and rear doors
Protection
ZINC PLATED
Cabinet frame, panel mount supports
and 19” panel mounting angles
1st number
Definition
0
No protection
1
Protected against solids objects over 50 mm (e.g. accidental touch by hands)
2
Protected against solids objects over 12 mm (e.g. fingers)
3
Protected against solids objects over 2.5 mm (e.g. tools and wires)
4
Protected against solids objects over 1 mm (e.g. tools, wires and small l wires)
5
Protected against dust - limited entry (no harmful deposit)
6
Totally protected against dust
Dimensions
Floor version
Depth: 600 - 800 mm
27U
Width: 600 - 800 mm
37U
42U
47U
2nd number
0
1
2
3
4
5
6
7
8
Definition
No protection
Protected against vertically falling drops of water
Protected against vertical direct sprays
Protected against vertical direct sprays up to 60°
Protected against sprays from all directions - limited entry permitted
Protected against sprays
Protected against strong jets of water
Protected against the effects of temporary immersion
Protected against long periods of immersion under pressure
VERAK® EMC / IP
Introduction
3
Introduction to VERAK® EMC / IP65
VERAK® cabinets are designed to satisfy the most specific
requirements of the communications, industrial networking
and electronics sectors, providing both IP65 environmental
protection and EMC screening. The cabinet is also available in
the EMC / IP versions. The EMC pro­vides protection from radio
frequency interference to ensure that electronic systems meet
electromagnetic compatibility require­ments and the IP provides
pro­tection from dust and water entry.
VERAK® EMC allows more than 80 dB at 100 MHz and 40 dB at 1
GHz, the highest levels available in a standard product from any
manufacturer. The EMC gaskets provide electrical continuity
between panels. They self-secure into slots punched in the
EMC screen, making it impossible to remove without a tool.
VERAK® is an extremely strong floor-standing enclosure. The 2
mm steel framework gives the VERAK® enclosure exceptional
strength and rigidity with a 1.000 Kg static load capacity. The
knifed edges that interact with the panel mounted gasket to
create the IP seal and give maximum support throughout the
structure are an integral part of the verticals. The sides of the
knifed edges ensure the maximum IP protection and the EMC
fingers guarantiee that the isolation is maintained throughout
the entire structure. Users can readily change the door hinging
from left to right without having to interfere with the IP or EMC
sealing.
VERAK® is available with steel or glass front and rear doors.
The EMC panels and doors are double skinned, consisting of an
inner conductive panel and an outer painted protective cover.
The EMC glass door is made of a laminated construction with
a fine metal mesh which is encapsulated between two, 3 mm
glass sheets in order to maintain ground con­tinuity. This also
allows visual inspection of the equipment without degrading
EMC performance.
The unique design of the closing mechanism, which includes a
wedge-shaped gasket, ensures the integrity of the IP and EMC
seals. A swing handle controls a four point over center cam
closure that exerts the correct pressure on the gaskets, thereby
avoiding over compression. The gasket is subjected to minimal
compression, so sealing and screening performance does not
degrade over time due to repeated door openings. This is a
great advantage because the cabinet is regularly opened for
use and rou­tine maintenance.
Cables can be brought into the rack from the top, through the
bottom and through 10U high recessed cable entry panels,
fitted above or below shortened front or rear doors. Recessed
panels en­sure that connectors do not protrude outside the
overall footprint of the enclosure and removable flat gland plates
make punching and drilling an easy job. The screened gland
plates provide cable entry capability without compromising the
EMC performance. VERAK®’s soft line, slightly curved design
is equally at home in the office, the communications room or
on the factory floor. Its two tone grey colour scheme is neutral,
blending with most modern decors, making VERAK® the ideal
choice for both heavy industrial and telecoms applications.
Key Features: VERAK® EMC / IP
• High RFI (Radio Frequency Interference) attenuation
• IP65 certified, enhanced protection against dust and moisture
• Ideal for telecomunication, protected datas transmition and
industrial
• Exceptional strength allows a maximum static load capacity
of 1.000 Kg;
• Secure four point door locking system
• User friendly multiple entry access points (rear and bottom)
• 4 standard height options 27U, 37U, 42U and 47U
• 2 depth options: 600 mm and 800 mm
• 2 width options: 600 mm and 800 mm
• EMC / IP shielded glass door or solid steel and removable
EMC / IP side panels
• Rear metal full height or shortened with 10U cable access
panel
• Standard front and rear adjustable 19” panel mounting angles
• Wide range of application specific accessories
• Supplied fully assembled and configured with accessories
• Castors with 65 Kg or 115 Kg load rate as optional;
• Additional bay version settled for bayed cabinet;
• Designed to mount the earth continuity kit compliant to EN
60950 norms
www.apw.eu.com Tel: +39 011 7725024
VERAK® EMC / IP
Technical specifications
“F” DIM WIDTH
BETWEEN VERTICALS
OPENING
‘L’
OPENING
‘M’
97.9
467.0
451.0
30.0 VENTED
TOP COVER
4.2 STANDDARD
TOP COVER
‘E’ RACK DEPTH
‘K’ FEET CENTRES
‘G’ DIM WIDTH
BETWEEN
VERTICALS
“H” CENTRE LINE FOR FEET
& BOLT DOWN HOLES
‘J’ BOLT DOWN HOLES
‘D’ DIM RACK WIDTH
Measurements in mm
‘C’ DIMENSION = TOTAL RACK HEIGHT
‘A’ DIMENSION = ‘B’ U HEIGHTS RACK WIDTH
465.3
59.7
20.0 GLAND PLATE
OPENING
451.0
SIDE
Rack dimensions
27U x 600 x 600
27U x 600 x 800
27U x 800 x 600
27U x 800 x 800
37U x 600 x 600
37U x 600 x 800
37U x 800 x 600
37U x 800 x 800
42U x 600 x 600
42U x 600 x 800
42U x 800 x 600
42U x 800 x 800
47U x 600 x 600
47U x 600 x 800
47U x 800 x 600
47U x 800 x 800
“A”
1201.8
1201.8
1201.8
1201.8
1646.3
1646.3
1646.3
1646.3
1868.5
1868.5
1868.5
1868.5
2090.8
2090.8
2090.8
2090.8
“B”
27
27
27
27
37
37
37
37
42
42
42
42
47
47
47
47
“C”
1311.8
1311.8
1311.8
1311.8
1756.3
1756.3
1756.3
1756.3
1978.5
1978.5
1978.5
1978.5
2205.0
2205.0
2205.0
2205.0
“D”
597.6
597.6
797.6
797.6
597.6
597.6
797.6
797.6
597.6
597.6
797.6
797.6
597.6
597.6
797.6
797.6
“E”
678.0
878.0
678.0
878.0
678.0
878.0
678.0
878.0
678.0
878.0
678.0
878.0
678.0
878.0
678.0
878.0
“F”
490.0
490.0
690.0
690.0
490.0
490.0
690.0
690.0
490.0
490.0
690.0
690.0
490.0
490.0
690.0
690.0
FRONT
“G”
440.0
640.0
440.0
640.0
440.0
640.0
440.0
640.0
440.0
640.0
440.0
640.0
440.0
640.0
440.0
640.0
“H”
558.0
758.0
558.0
758.0
558.0
758.0
558.0
758.0
558.0
758.0
558.0
758.0
558.0
758.0
558.0
758.0
“J”
380.0
380.0
580.0
580.0
380.0
380.0
580.0
580.0
380.0
380.0
580.0
580.0
380.0
380.0
580.0
580.0
“K”
450.0
450.0
650.0
650.0
450.0
450.0
650.0
650.0
450.0
450.0
650.0
650.0
450.0
450.0
650.0
650.0
“L”
393.4
593.4
393.4
593.4
393.4
593.4
393.4
593.4
393.4
593.4
393.4
593.4
393.4
593.4
393.4
593.4
“M”
363.8
363.8
563.8
563.8
363.8
363.8
563.8
563.8
363.8
363.8
563.8
563.8
363.8
363.8
363.8
363.8
VERAK® EMC / IP
Primary Configuration
5
Ready to use “Primary” cabinet builds
The VERAK® ‘Primary’ is a ready to use configured cabinet, one
order code gives you a complete ‘Primary’ enclosure ideal for
housing active equipment, electronics and computer servers. It
can also be used as a starting base in order to create your own
unique configured enclosure by adding additional accessories.
Contents of kit
Description
Corner verticals
End frames
19” panel mounting angles
Panel mounts supports kit of 2
Side panels
Top cover EMC / IP65
Bottom EMC screen EMC/IP65
Top EMC plain screen
Steel front door
Shortened metal rear door
10U recessed connectors panel
Reducing cabling channels (on 800mm wide)
Set of adjustable feet
Qty
4
2
4
2 or 3
2
1
1
1
1
1
1
4
1
VERAK® PRIMARY RACK BUILD
600 mm width
Dimensions
U Height
27U
37U
42U
47U
Description
Ventilated top
Heavy duty castors
Adjustable feet
Overall height mm
Internal height mm
1311.8
1201.8
1756.3
1646.3
1978.5
1868.5
2205.0
2090.8
Addition to height
25.8 mm
59.7 mm
Min. 25 Max. 60 mm
VERAK® PRIMARY RACK BUILD 800 mm wide
with 4 reducing cable channels
www.apw.eu.com Tel: +39 011 7725024
VERAK® EMC / IP
Primary Configuration
Ordering information
Height (U) W x D (mm)
27 EMC / IP65 600 x 600
37 EMC / IP65 600 x 600
27 EMC / IP65 600 x 800
37 EMC / IP65 600 x 800
42 EMC / IP65 600 x 600
42 EMC / IP65 600 x 800
42 EMC / IP65 800 x 600
42 EMC / IP65 800 x 800
Order code
VT589-790700
VT589-790701
VT589-790607
VT589-790702
VT589-790703
VT589-790704
VT589-790705
VT589-790706
VERAK® EMC/IP 47U 800x800
front glass door
VERAK® EMC/IP
10U recessed connectors panel
VERAK® EMC/IP 47U 800x800
shortened metal door
and 10U recessed
connectors panel
VERAK® EMC / IP
Structural elements
7
Frame
The frame comprises of 4 verticals and 2 end frames.
Glazed door
The EMC glass door is equipped with a thin metal mesh enclosed
between two sheets of 3 mm glass to maintain ground continuity
and IP gasket. A swing handle controls a 4-point locking
system with central camshaft holding the proper pressure on
the “fingers” for continuity. The options of the keyed alike lock,
manual or automatic, has to be ordered separately.
Shortened steel doors and 10U cable access panel
A shortened steel door needs to be ordered with the 10U cable
access panel. The cable access panel is recessed by 60mm so
cable connectors do not protrude out from the total dimension.
The panel can be fitted above or below the door and is easily
removed to facilitate the fitting of cable connectors etc. The
1.5 mm steel door comes complete with swing handle which
controls a 4-point locking system. Both solutions guarantee the
EMC and IP protection.The required lock, manual/automatic or
blank needs to be ordered separately.
Frame
Glazed door
Top / bottom plates
For VERAK EMC to work as an EMC enclosure top and bottom
pla­tes must be fitted.
Plain - This plain EMC shielding panel which can be fitted at
either the top or bottom of the rack can also be utilized as a
cable entry panel.
Shortned
steel door
Top / bottom
plates
Metal doors
1.5 mm EMC / IP steel door is complete with swing handle which
controls a 4-point locking system.The required lock manual/
automatic or blank lock needs to be ordered separately.
Side panels
EMC / IP side panels are sold in pairs and are 1.5 mm steel
painted in RAL7035. The side panels are fitted using captive
screws which allow the units to easily be fitted or removed.
Baying bracket kit
The kit consists of the required length of self-adhesive RFI
contact fingers and IP gasket material, plus 6 brackets.For
example: If three racks are to be bayed together to make one
suite of racks, one pair of ‘side panels’ are required (to be used
on either end of the suite) and two ‘baying bracket kits’.
Plain IP65 top
IP 65 unvented top cover.
Lifting eyes
Lifting eyes are sold as a kit of 4. Each has a load capacity up to
320 Kg.
Steel door
Top cover
Swing handles
Both the metal and glass doors have a swing handle fitted as
stan­dard. Please note, the locks for the swing handle need to be
or­dered separately.
Keyed alike lock - self locking
All locks supplied operate with the same key and the door
automatically locks when closed.
Keyed alike lock - manual locking
All locks supplied operate with the same key. To lock the door the
key must be turned.
Lock blank
The lock blank fills the hole in the swing handle when a lock is not
required. It also acts as a spring clip holding the handle into its
housing.
www.apw.eu.com Tel: +39 011 7725024
VERAK® EMC / IP
Handles & locks
VERAK® handles and locking systems
The Primary configurations provide swing handle with manual
locking.
They are optionally available versions with or without lock. Please
order the selected key lock separately
Swing handle
Description
Swing handle
Swing handle with numeric combination lock
Order code
VT802-563495
VA554-546642
Standard solution - Swing handle with manual locking
Lock
Description
Keyed alike lock - manual locking (2 keys)
Keyed alike lock - self locking (2 keys)
Blank cover
Order code
VA802-563610
VA802-563532
VA802-563534
Swing handle with blank cover
Swing handle with automatic locking
Swing handle with numeric combination lock
VERAK® EMC / IP
Accessories
9
Fixed shelves kit
Description
19” fixed shelf (600 mm) x 256
19” fixed shelf (600 mm) x 356
19” fixed shelf (600 mm) x 456
19” fixed shelf (600 mm) x 556
19” fixed shelf max 800 x 256
19” fixed shelf max 800 x 356
19” fixed shelf max 800 x 456
19” fixed shelf max 800 x 556
Order code
VT802-561013
VT802-561014
VT802-561015
VT802-561016
VT802-561017
VT802-561018
VT802-561019
VT802-561020
Chassis supports
Description
Chassis support 270 mm in cabinet 400 mm depth min.
Chassis support 370 mm in cabinet 500 mm depth min.
Chassis support 470 mm in cabinet 600 mm depth min.
Chassis support 570 mm in cabinet 700 mm depth min.
Chassis support 670 mm in cabinet 800 mm depth min.
Chassis support 770 mm
Chassis support 870 mm
Fixed shelves kit
Light grey
RAL 7035
Zinc plated
‘conductive’
Order code
VT802-561009
VT802-561561
VT802-561010
VT802-561562
VT802-561011
VT802-343186
VT802-343187
Order code
VT802-343304
VT802-343305
VT802-343306
VT802-343307
VT802-343308
VT802-343309
VT802-343310
19” Cantilever shelves
Description
19” cantilever shelf (255 mm deep)
19” cantilever shelf (400 mm deep)
Order code
VT802-562284
VT802-562285
Chassis supports
19” cantilever shelves
www.apw.eu.com Tel: +39 011 7725024
VERAK® EMC / IP
Accessories
Keyboard shelves
Description
19” x 400 mm keyboard shelf
Order code
VT802-3635758
19” Sliding drawing kit
Description
19” 2U sliding drawing kit RAL 7035
Order code
VT390-787964
Heavy duty sliding shelves
Keyboard shelf
Description
19” x 630 mm heavy duty sliding shelves
Order code
VT802-3635737
19” Din bar panel kit
Description
19” Din bar panel kit
Order code
VT390-787140-B
Plinth
Description
Plinth
Vented
plinth
Order code
Order code
600 x 600 / 600 x 800 rear / front panels
VT802-561038 VT806-600649
800 x 600 / 800 x 800 rear / front panels
VT802-561039 VT806-601221
600 x 600 / 800 x 600 side panels
600 x 800 / 800 x 800 side panels
4 corners kit
VT802-561035 VT806-601222
VT802-561036 VT806-600650
VT567-565504
19” Slideing drawing kit
Heavy duty sliding shelves
19” Din bar panel kit
Plinth
VERAK® EMC / IP
Accessories
11
Castors kit
Description
Heavy duty castors kit unbraked
Order code
VT567-565408
Heavy duty braked / unbraked castors kit
VT567-565409
Lifting eyes kit
Description
Lifting eyes kit
Order code
VT567-565489
Castors kit
Document holder
Description
Document holder A4 size
Order code
VT802-553081
Earth continuity
Description
Earth continuity kit
Earth continuity kit - supplied assembled
Order code
VT802-560005
VT567-565900
Lifting eyes kit
Document holder
www.apw.eu.com Tel: +39 011 7725024
VERAK® EMC / IP
Power Distribution Unit
Power Distribution Unit
1U 19” rackmount multistandard aluminum PDU
N.
A
sockets
Protection
Cable & Plug
Order code
--
6
16A
2 mt + Schuko
C06ALMST-SI2S
6
16A illuminated switch 2 mt + Schuko
C06ALMST-IL2S
7
16A
2P+N MGT
2 mt + Schuko
C07ALMST-MT2S
8
16A
--
2 mt + Schuko
C08ALMST-SI2S
8
16A illuminated switch 2 mt + Schuko
C08ALMST-IL2S
Multistandard aluminum PDU
1U 19” rackmount multistandard steel PDU
N.
A
sockets
Protection
Cable & Plug
Order code
--
2 mt + Schuko
K06MET-SI2S
6
16A
6
16A illuminated switch 2 mt + Schuko
6
16A
2P+N MGT
2 mt + Schuko
K06MET-MT2S
8
16A
--
2 mt + Schuko
K08MET-SI2S
8
16A illuminated switch 2 mt + Schuko
9
16A
2P+N MGT
2 mt + Schuko
K06MET-IL2S
Multistandard steel PDU
K08MET-IL2S
K09MET-MT2S
Multistandard aluminum vertical PDU
N.
A
sockets
Protection
Cable & Plug
Order code
12
16A
2P+N MGT
2 mt + Schuko
C12ALMST-MT2S
12
16A illuminated switch 2 mt + Schuko
C12ALMST-IL2S
16
16A illuminated switch 2 mt + Schuko
16
16A
2P+N MGT
2 mt + Schuko
C16ALMST-IL2S
C16ALMST-MT2S
Multistandard aluminum vertical PDU
1U 19” rackmount IEC C13 steel PDU
N.
A
sockets
Protection
Cable & Plug
Order code
8
16A illuminated switch 2 mt + Schuko
C08MET-16AC13IECIL2S
8
16A
12
16A illuminated switch 2 mt + Schuko
16
16A
--
3 mt + IEC 60309 K16MET-16AC13IECIND3MT
16
32A
--
3 mt + IEC 60309 K16MET-32AC13IECIND3MT
2P+N MGT
2 mt + Schuko C08MET-16AC13IECMT2S
C12MET-16AC13IECIL2S
IEC C13 8/12 sockets steel PDU
IEC C13 16 sockets steel PDU
VERAK® EMC / IP
Configurations Examples
13
VERAK® EMC Application: Industry
VERAK® EMC cabinet with shock absorbers on the bottom and
resilient support on the rear.
VERAK® EMC/IP Application: Industry
VERAK® EMC cabinet with IP51 protection rate. The cabinet is
provided of an integrated fan tray on the rear door, raised roof and
lower filters for air intake.
VERAK® EMC Application: Industry
VERAK® EMC Application: Industry
Series of cabinets from VERAK® EMC 42U 600 x 800 mm with plinth
and wheels option. The cabinets includes a customized painting color.
VERAK® EMC cabinet 27U 600 x 600, RAL 7016 color execution.
Configuration includes double front shielded glass door and a double
metal rear door that allows the use of the cabinet in narrow spaces,
maintaining the performance of radio frequency protection.
www.apw.eu.com Tel: +39 011 7725024
GOMA ELETTRONICA SpA
10146 Torino - Italy
Via Carlo Capelli, 89
Tel: +39 011 7725024
Fax: +39 011 712298
www.gomaelettronica.it
All trademarks are the property of their respective owners
GOMA ELETTRONICA SpA • MKA-CTG-EN 0517
Download PDF
Similar pages