COMMERCIAL
INFRARED STRIP HEATER
Operating Instruction Manual
ESH-24
ESH-36
ESH-60
ESH-48 & ESH-72 Not Shown
Model
Power
Amperage
ESH-24
500W
4.2A
ESH-36
850W
7A
36"
1100W
9.1A
48"
14.5A
72"
ESH-48
ESH-60
ESH-72
Voltage
120V ~ 60Hz
1400W
1750W
Chains for hanging are included. Undermount bracket is also included
with each item for wall-mounting.
Available separately:
• Undermount Bracket and Screws (ESH-UB)
• Hanging Chains (ESH-CH)
11.5A
Accessories:
Model
Length
Dimensions
24"
Depth
Height
6"
2.5"
60"
Description
ESH-CH
Hanging Chain
ESH-UB
Undermount Bracket and Screws
BEFORE OPERATING ANY EQUIPMENT, READ AND FAMILIARIZE YOURSELF WITH THESE USE AND SAFETY INSTRUCTIONS
Congratulations on your purchase of this WINCO® commercial infrared strip heater. WINCO takes pride in the
quality of its products. When used as intended and with proper care and maintenance, you will experience years of
reliable operation from this equipment. To ensure best results, it is important that you read and follow the instructions
in this manual carefully. It’s important to save these instructions for future reference.
Commercial Infrared Strip Heater
Important For Future Reference
Please complete this information and retain this manual for the life of the product. For
Warranty Service and/or parts, this information is required. Please see Page 10 for More
information on your Warranty and how to register.
ESH-
Model Number
!
!
!
ESH
Serial Number
Date Purchased
WARNING: Improper installation,
adjustment, alteration, service or
maintenance can cause property damage,
injury, or death. Read the installation,
operation, and maintenance instructions
thoroughly before installing
or servicing this equipment.
AVERTISSEMENT: Toute installation, réglage,
modification, réparation ou entretien
incorrect peut occasionner des dommages
matériels, des blessures graves ou la mort.
Lire les intructions d'installation, d'utilisation et
d'entretien attentivement avant d'installer ou de
réparer cet appareil.
CAUTION: These models are designed, built,
and sold for commercial use only. If these
models are positioned so the general public
can use the equipment, make sure that
caution signs, warnings, and operating
instructions are clearly posted near each
unit so that anyone using the equipment will
use it correctly and not injure themselves or
harm the equipment.
ATTENTION: Ces modèles sont conçus, fabriqués,
et vendus pour un usage commercial seulement.
Si ces modèles sont placés pour que le grand
public puisse les utiliser, assurez-vous que les
consignes d’attention, d'avertissement, et les
instructions d'utilisation soient clairement affichées
près de chaque unité de sorte que n'importe quel
utilisateur de l'appareil l'emploie correctement et ne
se blesse pas ou n'endommage pas l'appareil.
WARNING: A factory authorized service
provider should handle all maintenance
and repair. Before doing any maintenance
or repair, follow service set up
arrangement on page 8.
AVERTISSEMENT: Un technicien autorisé par
l'usine devra effectuer tout l'entretien et les
réparations. Avant de faire tout entretien ou
réparation, veuillez contacter WINCO.
!
!
!
Introduction
Congratulations on the purchase of your WINCO® machine. Please take the time to carefully read through this manual to ensure the
machine is operated and maintained properly, to ensure the best possible performance from this product for many years.
WINCO will not accept liability if:
• The instructions in this manual have not been followed correctly.
• Non-authorized personnel have tampered with the machine.
• Non-original spare parts are used.
• The machine has not been handled and cleaned correctly.
• There is any use damage to the unit.
2
Commercial Infrared Strip Heater
Table of Contents
Specifications........................................................................................ 1
Warnings ............................................................................................... 2
Introduction ......................................................................................... 2
Packaging ............................................................................................. 3
Important Safeguards......................................................................... 4
Cautions Before Use ............................................................................ 5
Electrical Requirements ..................................................................... 5
Operation ............................................................................................. 6
Cleaning & Maintenance .................................................................... 6
Safety .................................................................................................... 7
Service, Repair, Troubleshooting....................................................... 7
Exploded View and Parts List ............................................................ 8
Limited Warranty .............................................................................. 10
Package Contents
Unpacking the Equipment
All units come with an Operating Instruction Manual
and the following:
• Electric Strip Heater
• Hanging Chains (ESH-CH)
• Undermount Brackets (ESH-UB)
Dispose of all packaging materials in an
environmentally responsible manner.
1. Remove all packing materials and tape, as well as any
protective plastic and cardboard, from the unit.
2. Clean any glue residue left over from the plastic or tape.
3. Place the unit in the desired position and height.
Save the original box and packaging for use in
packaging and shipping the equipment if services
are needed.
WINCO prides itself on quality and service, ensuring that at the
time of packing, all products are supplied fully functional and
free of damage. Should you find any damage as result of freight,
please contact your WINCO dealer immediately.
Function and Purpose
This unit is intended for use in commercial food-service operations only. It is not intended for household, industrial or laboratory use.
NOTE
Please remember that this manual and the warning labels do not replace the need to be alert, to
properly train and supervise operators, and to use common sense when using this equipment.
3
Important Safeguards
To ensure safe installation and operation, please carefully read and understand the following statements.
Unless the operator is adequately trained and supervised there is a possibility of serious injury. Owners of
this equipment bear the responsibility to make certain that this equipment is used properly and safely, and to
strictly follow all of the instructions contained in this manual and the requirements of local, state or federal law.
Owners should not permit anyone to touch this equipment unless they are over 18 years old, are adequately
trained and supervised, and have read and understood this manual.
Owners should also ensure that no customers, visitors or other unauthorized personnel come in contact with
this equipment. It is the responsibility of the owner and the operator to remain alert to any hazards posed by the
function of this equipment.
If there is ever uncertainty about a particular task or the proper method of operating this equipment, ask an
experienced supervisor.
Warnings
This manual contains a number of precautions to follow to help promote safe use of this equipment.
CAUTION
This appliance is hot when in use. Do not let bare skin touch hot
surfaces! Always keep flammable/combustible materials such as
curtains, napkins, flammable cleaners, etc., away from the unit.
WARNING
HOT
Use caution when
touching the unit.
AVERTISSEMENT
Ne touchez pas le liquide chaud
ou les surfaces de chauffage
lorsque l’appareil chauffe ou en
fonctionnement.
Power must be disconnected at the power
source prior to cleaning, or performing any
service procedure or repairs.
FOR YOUR SAFETY
ESURE DE SECURITE
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
Ne pas entreposer ni utiliser de'essence ni autres vapeurs ou liquides
inflammables a proximte de cet appareil ou de tout autre apparel!
WARNING
AVERTISSEMENT
Improper installation, adjustment, alteration, service or
maintenance can cause property damage, injury or death.
Read these installation, operating and maintenance
instructions thoroughly before installing or servicing this
equipment.
TO PURCHASER
Contact your local gas supplier and ask for instructions in the
event the user smells gas. This information should be posted
in a prominent location.
4
WARNING
Linstallation, le reglage, la modification, la reparation
ou I'entretien incorrect de cet appareil peut causer
des dommages materiels, des blessures ou la mort.
Lire attentivement les instructions d'installation, de
fonctionnement et d'entretien avant de proceder a son
installation ou entretien.
À L'ACHETEUR
CommunIquez avec votre distributeur de gaz et informez vous
quant aux procédés a suivre si vous détectez une odeur de
gaz. Cette information doit etre affichée a un endroit facile
d'acces et tres visible.
Warning
Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the
installation, operation, and maintenance instructions thoroughly before installing or servicing this equipment.
Caution Before Using Appliance
1. Read all instructions carefully. Do not use this appliance for
anything other than its intended use.
2. Do not touch surfaces that may be hot - be sure to always
use handles or knobs.
3. Unplug from outlet when not in use, prior to installing or
removing parts, and before cleaning. Allow for the device
to cool first.
WARNING
Electrical Shock Hazard
Keep water and other liquids
from entering the inside of the
unit. Liquid inside the unit could
cause an electrical shock.
Do not spray water or cleaning
products. Liquid could contact
the electrical components
and cause a short circuit or an
electrical shock. Do not use unit
if power cord is damaged or has
been modified.
AVERTISSEMENT
Risque de choc électrique
Conserver l'eau et d'autres liquides
de pénétrer à l'intérieur de l'appareil.
Liquide à l'intérieur de l'appareil pourrait
provoquer un choc électrique.
Ne pas pulvériser de l'eau ou des produits
de nettoyage. Le liquide pourrait contacter
avec les composants électriques et causer
un court-circuit ou un choc électrique.
Ne pas utiliser l'appareil si le cordon
d'alimentation est endommagé.
ou a été modifié.
4. To protect against the risk of electrical shock, do not
immerse the appliance, cord or plug in water or other
liquids.
5. Do not use an adapter.
6. Do not use an extension cord.
7. Do not remove ground.
Proper Grounding
This machine is provided with a
three-pronged grounding plug.
The outlet to which this plug
is connected must be properly
grounded. If the receptacle is
not the proper grounding type,
contact an electrician. DO NOT,
under any circumstances, cut or
remove the third ground prong
from the power cord or use any
adapter plug.
USE A GROUNDED OUTLET
DO NOT ADD AN ADAPTER
TO THE PLUG
8. Do not operate this device or any other electrical equipment
with a damaged switch, cord or plug, or after the unit
malfunctions, is dropped or damaged in any manner.
Return to the nearest WINCO Authorized Service Center for
examination, repair, and / or adjustment.
9. The use of accessory attachments not recommended by
WINCO may cause fire, electric shock or injury.
WARNING
AVERTISSEMENT
Fire Hazard.
Risque d'incendie
Correct installation precautions,
procedures and regulations
must be followed. Operation
and safety training is necessary
for all users of this equipment.
La surchauffe des vapeurs d'huile ou de
l'huile peut s'enflammer et provoquer
un incendie. Surveillez la température,
la qualité et le niveau d’huile. Utilisez et
entretenez le système d'élimination des
vapeurs d'huile.
10.Not intended for outdoor installation.
11.Do not let the cord hang over the edge of a table or counter,
or touch hot surfaces.
12.Do not place on or near a heat source.
13.This appliance should always be on a stable and steady
countertop or table when legs are in use.
14.When using the undermount brackets (ESH-UB), make sure
to secure the unit to a stable, noncombustible surface (such
as a metal shelf).
15.This appliance is not intended for use by individuals
(including children) with reduced or impaired physical,
sensory, or mental capabilities, or lack of experience or
knowledge, unless they have been given proper supervision
or instruction concerning the use of this appliance by a
person responsible for their safety.
16.Children should be supervised at all times to avoid injuring
themselves or damaging the appliance in any way.
17.Clean the unit with caution – do not clean when unit is
plugged in or when hot.
18.Do not place metal objects such as knives, forks or spoons
in the heater as it may damage the unit, and may also result
in injury.
19.Do not store any item on top of this unit when in operation.
20.Never place materials such as paper, cardboard, plastic, etc.
on or under this unit.
5
Operation
1.
2.
3.
4.
5.
Plug power cord into a receptacle.
Turn the POWER switch to the ON (up) position.
The red HEAT indicator should light up when on.
Place food products under the heater to keep warm.
Turn the POWER switch to the OFF (down) position to turn off when not in use.
When attaching undermount brackets, install unit to the mounting surface with the following clearances:
9” minimum clearance between end of the unit and any/all walls
12” min. clearance between side of unit and any wall
16” min. clearance between bottom of unit and countertop surface
2” min. clearance between top of unit and any overhead surface
CAUTION: HOT!
CAUTION
The unit will be HOT after use!
Let cool before cleaning.
HOT
Cleaning & Maintenance
Before using this equipment it must be cleaned and dried thoroughly. Clean all surfaces before use.
Failure to clean surfaces before using the unit could cause food contamination.
Always unplug the unit after every use and before cleaning. Unplug the unit when not in operation.
• Allow unit to cool completely before cleaning.
• Clean main body with a damp cloth and degreaser solution if desired.
• Allow to dry before turning the unit back on.
• Do not immerse the device completely in water to clean. The appliance should also NOT be cleaned with a water jet.
NOTE:
Proper cleaning instructions must be followed; otherwise, operation of the unit may be seriously impaired. Do not
wash parts in an automatic dishwasher.
WINCO authorized service personnel must perform any other servicing.
6
Safety
Service and Repair
A WINCO® Approved Service Technician should carry out repairs
if necessary. Do not remove any components or service panels on
this product.
If the power cord is damaged, it must be replaced by a WINCO
Approved Service Technician in order to avoid a hazard.
There are no user serviceable parts within this appliance.
To avoid serious injury or damage, never attempt to repair the
unit yourself.
To initiate warranty service contact: support@wincous.com
or call: 973-295-3899.
DO NOT send unit to WINCO without first contacting our
customer service department.
See "Limited Warranty" section on page 8 for details.
Troubleshooting
If your WINCO Infrared Strip Heater does not operate, please check the following prior to placing a service call.
PROBLEM
POSSIBLE CAUSE
RECOMMENDED SOLUTION
Power supply cord
Check that the power supply cord is correctly
plugged in and outlet is working.
Switches have not been turned on
Check that the switch is in the ON position.
The unit is not turning on
Plug/cord or external wiring is damaged
Internal wiring fault
Call WINCO to make service arrangements
through their service provider network.
Heater needs replacement if light is on
Call WINCO to make service arrangements
through their service provider network.
Light does not come on
See "unit is not turning on" section.
Does not get hot
See "unit is not turning on" section.
It gets hot but only the light is off
Light/switch/wiring needs to be replaced.
Call WINCO to make service arrangements
through their service provider network.
The unit is not heating up
Heating light does not come
7
Exploded View
MODEL: ESH-Series Strip Heater
1) cover plate
AA
DD
2) cover
3) END CAP
BB
CC
EE
FF
4) STRIP HEATER ASSEMBLY
CC / EE
GG
(Product Ratings)
HH
II
JJ
CC / Washer
KK
LL
MM
8
Parts List
MODEL: ESH-Series Strip Heater
AA
Ref.
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
MM
Ref.
KK
LL
BB
CC
DD
EE
description
Screw 8 x 1/2"
Screw 8-32 x 3/8"
Screw 8-32 x 1/4"
Screw 6-32 x 1/2"
Keps Nut 8-32
Cover Plate
Heating Element Guard
Support - Top
Support - Bottom
Element (120V)
Thermostat
REPLACEMENT PARTS
QTY
4
6
6
2
4
1
1
1
1
1
1
QTY
Item#
Indicator light (red)
Toggle switch
Undermount bracket and screws
Metal Hanging chain
1
1
1 (Set)
2 per unit
FWS500-P10
ESH-P1
ESH-UB
ESH-CH
9
Limited Warranty
WINCO® warrants to the original purchaser of new equipment that said equipment, when installed in accordance with our instructions
within North America and subjected to normal use, is free from defects in material or workmanship for a period of 1 year. The labor
warranty is one year from original installation or 18 months from actual factory shipment date, whichever date occurs first.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED. WINCO EXPRESSLY DISCLAIMS
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESSED OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE.
WINCO’S OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIRING AND REPLACING
EQUIPMENT THAT PROVES TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITHIN THE APPLICABLE WARRANTY
PERIOD.
IN NO EVENT SHALL WINCO BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY,
INCLUDING, WITHOUT LIMITATION, LOSS OF PROPERTY, PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER
ECONOMIC LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES, WHETHER IN NEGLIGENCE, WARRANTY, STRICT LIABILITY,
OR OTHERWISE.
This warranty is given only to the first purchaser from a retail dealer. No warranty is given to subsequent transferees.
Warranty does not cover product failures caused by: failure to maintain, neglect, abuse, damage due to excess water, fire, normal wear,
improper set up and use. Periodic maintenance is not covered.
This warranty is not in force until such time as a properly completed and digitally signed Installation/Warranty Registration has been
received by WINCO within 30 days from the date of installation.
Warranty Service
To initiate warranty service contact: support@wincous.com
or call: 973-295-3899
DO NOT send unit to WINCO® without first contacting our customer service department.
Register online at:
http://support.wincous.com
Proof of purchase is required to extend warranty more than 1 year from date of shipment from the factory.
10
Limited Warranty
THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND EXCLUSIVE STATEMENT BETWEEN THE BUYER AND SELLER.
WINCO® NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN
CONNECTION WITH SAID EQUIPMENT.
Examples of items not covered under warranty, but not limited to just these items:
1. Acts of God, fire, water damage, burglary, accident, theft.
2. Freight damage.
3. Improper installation or alteration of equipment.
4. Use of generic or after-market parts.
5. Repairs made by anyone other than a WINCO® designated service provider.
6. Lubrication.
7. Expendable wear parts, adjustable feet, blown fuses, lamps, etc.
8. Cleaning of equipment.
9. Misuse or abuse.
WARRANTY REGISTRATION
SCAN THE QR CODE WITH YOUR MOBILE DEVICE
or go to
http://support.wincous.com
TO FILL OUT AND SUBMIT YOUR WARRANTY REGISTRATION.
Please keep this manual in a safe place for future use!
11
Model: ESH-Series
www.wincous.com
Download PDF
Similar pages