INDUCTION HOB
Model: HCI604TB1
INSTALLATION AND USER INSTRUCTIONS
Please read the instruction manual carefully before operating your new hob.
Safety Warnings
Your safety is important to us. Please read this information before using your cooktop.
Electrical Shock Hazard
• Disconnect the appliance from the mains electricity supply before carrying out any work or maintenance on it.
• Connection to a good earth wiring system is essential and mandatory.
• Alterations to the domestic wiring system must only be made by a qualified electrician.
• Failure to follow this advice may result in electrical shock or death.
Cut Hazard
• Take care - appliance edges are sharp.
• Failure to use caution could result in injury or cuts.
Important safety instructions
• No combustible material or products should be placed on this appliance at any time.
• Please make this information available to the person responsible for installing the appliance as it could reduce your
installation costs.
• In order to avoid a hazard, this appliance must be installed according to these instructions for installation.
• This appliance is to be properly installed and earthed only by a suitably qualified person.
• Failure to install the appliance correctly could invalidate any warranty or liability claims.
Operation and maintenance
Electrical Shock Hazard
• Do not cook on a broken or cracked cooktop. If the cooktop surface should break or crack,switch the appliance off immediately at the mains power supply (wall switch) and contact a qualified technician.
• Switch the cooktop off at the wall before cleaning or maintenance.
• Failure to follow this advice may result in electrical shock or death.
Health Hazard
• However, persons with cardiac pacemakers or other electrical implants (such as insulin pumps) must consult with their doctor
or implant manufacturer before using this appliance to make sure that their implants will not be affected by the electromagnetic
field.
• Failure to follow this advice may result in death.
Hot Surface Hazard
• During use, accessible parts of this appliance will become hot enough to cause burns.
• Do not let your body, clothing or any item other than suitable cookware contact the Induction glass until the surface is cool.
• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot
• Keep children away.
• Handles of saucepans may be hot to touch. Check saucepan handles do not overhang other cooking zones that are on. Keep
handles out of reach of children.
• Failure to follow this advice could result in burns and scalds.
Cut Hazard
• The razor-sharp blade of a cooktop scraper is exposed when the safety cover is retracted.Use with extreme care and always
store safely and out of reach of children.
• Failure to use caution could result in injury or cuts.
Important safety instructions
• Never leave the appliance unattended when in use. Boilover causes smoking and greasy spillovers that may ignite.
• Never use your appliance as a work or storage surface.
Never leave any objects or utensils on the appliance.
• Do not place or leave any magnetisable objects (e.g. credit cards, memory cards)or electronic devices (e.g. computers, MP3
players) near the appliance, as they may be affected by its electromagnetic field.
• The kitchen should not be immersed in water or under running water or any kind of liquids.
• Never use your appliance for warming or heating the room.
• After use, always turn off the cooking zones and the cooktop as described in this manual (i.e. by using the touch controls). Do
not rely on the pan detection feature to turn off the cooking zones when you remove the pans.
• Do not allow children to play with the appliance or sit, stand, or climb on it.
• Do not store items of interest to children in cabinets above the appliance. Children climbing on the cooktop could be seriously
injured.
• Do not leave children alone or unattended in the area where the appliance is in use.
• Children or persons with a disability which limits their ability to use the appliance should have a responsible and competent
person to instruct them in its use. The instructor should be satisfied that they can use the appliance without danger to
themselves or their surroundings.
• Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should
be done by a qualified technician.
• Do not use a steam cleaner to clean your cooktop.
• Do not place or drop heavy objects on your cooktop.
• Do not stand on your cooktop.
• Do not use pans with jagged edges or drag pans across the Induction glass surface as this can scratch the glass.
• Do not use scourers or any other harsh abrasive cleaning agents to clean your cooktop, as these can scratch the Induction
glass.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
•This appliance is intended to be used in household and similar applications such as: -staff kitchen areas in shops, offices and
other working environments; -farm houses; -by clients in hotels, motels and other residential type environments ; -bed and
breakfast type environments.
•WARNING: The appliance and its accessible parts become hot during use.
Care should be taken to avoid touching heating elements.
Children less than 8 years of age shall be kept away unless continuously supervised.
•This appliance can be used by children aged from 8 years and above and persons with reduced physical,sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
•Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
•WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.NEVER try to extinguish a fire
with water, but switch off the appliance
and then cover flame e.g. with a lid or a fire blanket.
•WARNING: If the surface is cracked, switch off the appliance to avoid
the possibility of electric shock, for hob surfaces of glass-ceramic or similar material which protect live parts
•A steam cleaner is not to be used.
•The appliance is not intended to be operated by means of an external timer or separate remote-control system.
CAUTION:The cooking process has to be supervised.A short term cooking process has to be supervised continuously.
WARNING:In order to prevent tipping of the appliance,this stabilizing means must be installed.Refer to the instructions for
installation.
WARNING:Use only hob guards designed by the manufactuer of the cooking appliance or indicated by the manufacture of the
appliance in the instruction for use as suitable or hob guards incorporated in the appliance.The use of inappropriate guards can
cause accidents.
This appliance incorporates an earth connection for functional purposes only
Congratulations on the purchase of your new Induction Hob.
We recommend that you spend some time to read this Instruction / Installation Manual in order to fully understand how to install
correctly and operate it.
For installation, please read the installation section.
Read all the safety instructions carefully before use and keep this Instruction / Installation Manual for future reference.
Danger of fire: Do not store items on the cooking surfaces.
CAUTION: The cooking process has to be supervised. short term
cooking process has to be supervised continuously.
WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in a fire.
2
1
PRODUCT OVERVIEW
Top View
Surface
Max. 2000W
zone
Max. 1500W
zone
Max. 2000W
zone
5
1
3
2
1
4
1. Heating zone selection controls
2. Power / Timer regulating key
3. keylock control
4. ON/OFF control
5. Timer control
Max. 1500W
zone
Control panel
TECHNICAL DATA
Power
Model
Power supply
HCI604TB1
Heating area
(210mm)
Heating area
(180mm)
Heating area
(140mm)
Size (mm)
2000W
2000W
1500W
590x520x62
AC 220-240V 50/60Hz
When you have finished cooking
1. Touching the heating zone selection control that you wish to switch off
2. Turn the cooking zone off by scrolling down to ”0” . Make sure the display shows”0”,then show”H”.
3. Turn the whole cooktop off by touching the ON/OFF control.
4. Beware of hot surfaces: “H” will show which cooking zone is hot to touch. It will disappear when the surface has
cooled down to a safe temperature. It can also be used as an energy saving function if you want
to heat further pans, use the hotplate that is still hot.
!
Note:When “H” is shown on display, although he hob is off, but the temperature of induction glass
is still very high, do not let your fingers touch induction glass directly in case of scalds.
Note: After use, switch off the hob element by its control and do not rely on the pan detector.
Using the Touch Controls
• The controls respond to touch, so you don’t need to apply any pressure.
• Use the ball of your finger, not its tip.
• You will hear a beep each time a touch is registered.
• Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth)
covering them. Even a thin film of water may make the controls difficult to operate.
Choosing the right Cookware
• Only use cookware with a base suitable for induction cooking. Look for the induction symbol on the packaging or on the
bottom of the pan.
• You can check whether your cookware is suitable by carrying out a magnet test. Move a magnet towards the base of the pan.
If it is attracted, the pan is suitable for induction.
• If you do not have a magnet:
1. Put some water in the pan you want to check.
2. If “
” does not flash in the display and the water is heating, the pan is suitable.
• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or copper without a magnetic
base, glass, wood, porcelain, ceramic, and earthenware.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone. Use pans
whose diameter is as large as the graphic of the zone selected.Using a pot a slightly wider energy will be used at its maximum
efficiency.If you use smaller pot efficiency could be less than expected.Pot less than 140 mm could be undetected by the hob.
Always centre your pan on the cooking zone.
Always lift pans off the Induction hob – do not slide, or they may scratch the glass.
Bad
Bad
Bad
(recessed base) (convex base) (undersize)
Bad
(oversize)
Bad
Bad
(moisture on hotplate) (no utensil)
Bad
To start cooking
1. Power On
When the mains power supply is switched on, the buzzer beeps once and all the indicators light up for 1
second, then go out. This indicates that the ceramic hob has entered standby mode.
When the hob is in the standby mode all the indicator lights do not shine, all the controls are disable
except the “ON/OFF” and “keylock” control.
2. Touch the ON/OFF control.
After power on, the buzzer beeps once, all displays show “ – “ or “ – – “, indicating that the induction hob has
entered the state of power on status.
3
5、If the display flashes “ ” alternately with the heat setting
This means that:
• you have not placed a pan on the correct cooking zone or,
• the pan you’re using is not suitable for induction cooking or,
• the pan is too small or not properly centred on the cooking zone.
No heating takes place unless there is a suitable pan on the cooking zone.
The display will automatically turn off after 1 minutes if no suitable pan is placed on it.
Cooling fan
When the hob starts heating, the cooling fan will start work together. When heating area stops work,
cooling fan will keep working for additional 2 minutes then stop.
Before using your New Induction Hob
• Read this guide, taking special note of the ‘Safety Warnings’ section.
• Remove any protective film that may still be on your Induction hob.
Good
When the hob is on, touch“ON/OFF” , all heating areas will be off. Another touch means the hob enters power
on status.
3. Place a suitable pan on the cooking zone that you wish to use.
• Make sure the bottom of the pan and the surface of the cooking zone are clean and dry.
4. Touching the heating zone selection control ,and a indicator next to the key will flash
• Select a heat setting by touching the “-“ or “+” control.
• If you don’t choose a heat setting within 1 minute, the Induction hob will automatically switch off. You will need
to start again at step 2.
• You can modify the heat setting at any time during cooking.
Locking the Controls
• You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones on).
• When the controls are locked, all the controls except the ON/OFF control are disabled.
To lock the controls
Touch the keylock control . The timer indicator will show “ Lo ”
To unlock the controls
1. Make sure the Induction hob is turned on.
2. Touch and hold the keylock contro for 3s
3. You can now start using your Induction hob.
When the hob is in the lock mode,all the controls are disable except theON/OFF , you can always turn the induction
hob off with the ON/OFF control in an emergency,but you shall unlock the hob first in the next operation
Over-Temperature Protection
A temperature sensor equipped can monitor the temperature inside the Induction hob. When an excessive temperature
is monitored, “E3” or “E5” is shown on display, the hob will be off, internal cooling fan keep running until internal
temperature is cool, then the hob will re-start heating.
Detection of Small Articles
When an unsuitable size or non-magnetic pan (e.g. aluminium), or some other small item (e.g. knife, fork, key) has
been left on the hob, the hob automatically go on to standby in 1 minute. The fan will keep cooking down the induction
hob for a further 2 minute.
Auto Shutdown Protection
Auto shut down is a safety protection function for your induction hob. It shut down automatically if ever you forget to
turn off your cooking. The default working times for various power levels are shown in the below table:
Good
Power level
Default working timer (hour)
1
2
3
4
5
6
8
8
8
4
4
4
7
8
9
2.0 2.0 2.0
When the pot is removed, the induction hob can stop heating immediately and the hob automatically
switch off after 1minutes.
!
People with a heart pace maker should consult with their doctor before using this unit.
Using the Timer
• You can set it to turn one cooking zone off after the set time is up.
• You can set the timer up to 99 minutes.
4
6
Setting the timer to turn one cooking zone off
Cooking zones set for this feature will:
1. Touching the heating zone selection control that you want to set the timer for.
2. Touch timer control , The minder indicator will start flashing and “30” will show in the timer display,And red
point near the heating zone will be lighted
3. Set the time by touching the “-“ or “+” control of the timer
Hint: Touch the “-“ or “+” control of the timer once will decrease or increase by 1 minute.
Touch and hold the ”-“ or “+” control of the timer will decrease or increase by 10 minutes.
4. Touching the “-“ , when the “00” shows in the minute display, the timer is cancelled, .
5. When the time is set, it will begin to count down immediately. The display will show the remaining time
and the timer indicator flash for 5 seconds.
6. When cooking timer expires, the corresponding cooking zone will be switch off automatically.
7. Timer for multiple heating areas delay off, the shortest delay off time will be shown on display. If want to
check remained delay off time of other heating area, you should press button for different heating area.
NOTE: After setting delay off time, the time shown on display means heating area with red point twinkling.
!
30
Other cooking zone will keep operating if they are turned on previously.
Cooking Guidelines
Take care when frying as the oil and fat heat up very quickly. At extremely high termperatures oil and
! fat will ignite spontaneously and this presents a serious fire risk.
Heat Settings
The settings below are guidelines only. The exact setting will depend on several factors, including your cookware and
the amount you are cooking. Experiment with the induction hob to find the settings that best suit you.
Heat setting
1-2
Suitability
● Delicate warming for small amounts of food
● Melting chocolate, butter, and foods that burn quickly
● Gentle simmering ● Slow warming
● Reheating ● Rapid simmering ● Cooking rice
● Pancakes
● Cooking pasta
● Stir-frying ● Searing ● Bringing soup to the boil
3-4
5-6
7-8
9
● Boiling water
3. Spillovers on the touch controls
1). Switch the power to the cooktop off.
2). Soak up the spill
3). Wipe the touch control area with a clean damp sponge or cloth.
4). Wipe the arta completely dry with a paper towel.
5). Switch the power to the cooktop back on.
NOTE: The cooktop may beep and turn Itself off, and the touch controls may not function while there is liquid on them.
Make sure you wipe the touch control area dry before turning the cooktop back on.
Hints and Tips
1. The induction hob cannot be turned on.
May be there is no power: Make sure the induction hob is connected to the power supply and that it is switched on.
Check whether there is a power outage in your home or area. If you’ve checked everything and the problem persists,
call a qualified technician.
2. The touch controls are unresponsive.
The controls are locked: Unlock the controls. See section using your induction cooktop for instructions.
3. The touch controls are difficult to operate.
There may be a slight film of water over the controls or you may be using the tip of your finger when touching the controls:
Make sure the touch control area is dry and use the ball of your finger when touching the controls.
4. The glass is being scratched.
Tough-edged cookware. Unsuitable, abrasive scourer or cleaning products being used: Use cookware with flat and
smooth bases. See choosing the right cookware. See “Care and cleaning”.
5. Some pans make crackling or clicking noises.
This may be caused by the construction of your cookware (layers of different metals vibrating differently): This is normal,
but the noise should quieten down or disappear completely.
6. The induction hob makes a low humming noise when used on a high heat setting.
This is caused by the technology of induction cooking: This is normal, but the noise should quieten down or disappear
completely when you decrease the heat setting.
7. Fan noise coming from the induction hob.
A cooling fan built into your induction hob has come on to prevent the electronics from overheating. It may continue to run
even after you’re turned the induction hob off: This is normal and needs no action. Do not switch the power to the
induction hob off at the wall while the fan is running.
8. Pans do not become hot and appears “
” in the display.
The induction hob cannot detect the pan because it is not suitable for induction cooking. The induction hob cannot detect
the pan because it is too small for the cooking zone or not properly centred on it: Use cookware suitable for induction
cooking. See section ‘Choosing the right cookware’.
Centre the pan and make sure that its base matches the size of the cooking zone.
9. The induction hob or a cooking zone has turned itself off unexpectedly, a tone sounds and an error code is
displayed (typically alternating with one or two digits in the cooking timer display).
Technical fault: Please not down the error letters and numbers, switch the power to the induction hob off at the wall, and
contact a qualified technician.
Failure Display and Inspection
If an abnormality comes up, the induction hob will enter the protective state automatically and display
corresponding protective codes:
Care and cleaning
Problem
1. Everyday soiling on glass (fingerprints, marks, stains left by food of non-sugary spillovers on the glass).
1)Switch the power to the cooktop off;
2)Apply a cooktop cleaner while the glass is still warm (but not hot!)
3)Rinse and wipe dry with a clean cloth or paper towel.
4)Switch the power to the cooktop back on.
Possible causes
The appliance
does not work
During heating,
the unit stop work.
NOTE: ● When the power to the cooktop is switched off, there will be no hot surface indication but the cooking zone may
still be hot! Take extreme care.
● Heavy-duty scourers, some nylon scourers and harsh/abrasive cleaning agents may scratch to check if your
cleaner or scourer is suitable.
● Never leave cleaning residue on the cooktop: the glass may become stained.
2. Boilovers, melts, and hot sugary spills on the glass
U
E2
E1
Remove these immediately with a fish slice, palette knife or razor blade scraper suitable for induction glass cooktops, but
beware of hot cooking zone surfaces:
1). Switch the power to the cooktop off at the wall.
2). Hold the blade or utensil at a 30°angle and scrape the soiling or spill to a cool area of the cooktop.
3). Clean the soiling or spill up with a dish cloth or paper towel.
4). Follow steps 2 to 4 for everyday soiling on glass above.
F3
F4
E5
NOTE: ● Remove stains left by melts and sugary food or spillovers as soon as possible. If left to cool on the glass, they
may be difficult to remove or even permanently damage the glass surface.
● Cut hazard: then the safety cover is retracted, Use with extreme care and always store safely and out of rech
of children.
5
E3
F9
FA
Break in power supply
Delay off timer activates.
What to do
Please check the main power is normal; if the leakage protection switch is off; if there is a blown fuse,
replace it with a new one; if the main power is normal, check if the plug is connect with socket
appropriately; If the hob is wire connection type, disconnect the power, check if the wire is loose;
disconnect the power, check if main plug is off; Exclude above reasons, should be appliance fault, send
it to service center for repairing.
Please check if set delay off function. If set delay off function, the unit will stop once delay off time out.
No pan, please put proper pan. PCB synchronization or drive circuit fault, please send the
appliance to service center for repairing.
Low voltage, voltage of the main power is less 180V. Please check if voltage of the main power is normal.
Once voltage of the main power returns normal, re-start the unit. Voltage of PCB fault, please send the
Input power too low
unit to service center for repairing.
High voltage, voltage of the main power exceeds 250V. Please check if voltage of the main power is
normal. Once voltage of the main power returns normal, re-start the unit. Voltage of PCB fault, please
Input power too high
send the unit to service center for repairing.
Thermistor of coil short circuit. Sensor of coil thermistor connection error. Or detection part of PCB coil thermistor failure,
Thermistor of coil open circuit. send to service center for reparing.
Too high temperature of IGBT thermistor, air outlet is blocked. Open air outlet, re-start the unit. If still
unsolved, it is possible that cooling fan connection error, cooling fan damaged, or drive circuit of fan
Too high temperature
failure, send to service center for repairing. IGBT temperature sensor open circuit /short circuit.
of IGBT thermistor.
Temperature detection part of PCB IGBT failure, send to service center for repairing.
No pan or pan unsuitable
Too high temperature on induction glass surface, please check if there is no water in pan. After
treatment, connect with power again. If still unsolved, it is possible that sensor of cooktop failure, send to
service center for repairing.
IGBT thermistor short circuit Senor of IGBT thermistor connection error. Or detection part of IGBT PCB sensor failure,
IGBT thermistor open circuit send to service center for repairing.
Too high temperature
of coil thermistor.
6
The above are the judgment and inspection of common failures.
Please do not disassemble the unit by yourself to avoid any dangers and damages to the induction hob.
Installation
This hob installation with 2 ways:
1. Desktop installation
Do not place any item arond and botton of the hob.
Do not block the air inlet and outlet
2. Built-in Installation
Selection of installation equipment
Cut out the work surface according to the sizes shown in the drawing.
For the purpose of installation and use, a minimum of 5 cm space shall be preserved around the hole.
Be sure the thickness of the work surface is at least 30mm. Please select heat-resistant work surface material to avoid
larger deformation caused by the heat radiation from the hotplate. As shown below:
L(mm)
W(mm)
H(mm)
D(mm)
A(mm)
B(mm)
X(mm)
590
520
62
58
560
490
50 mini
Under any circumstances, make sure the Induction cooker hob is well ventilated and the air inlet and outlet are not blocked.
Ensure the Induction cooker hob is in good work state. As shown below
!
Note: The safety distance between the hotplate and the cupboard above the hotplate should be at least 760mm.
A
B
F
C
F
G
A(mm)
B(mm)
C(mm)
D
E
760
50 mini
20 mini
Air intake
Air exit ≥5mm >35mm <50mm
>2cm
Note: There must be have a 560x5mm holes on front
of cooker top position E, to dissipate heat air.
G
Before locating the fixing brackets
The unit should be placed on a stable, smooth surface (use the packaging). Do not
apply force onto the controls protruding
from the hob.
Adjusting the bracket position
Fix the hob on the work surface by screw 4 brackets on the bottom of hob(see
picture) after installation.
Adjust the bracket position to suit for different table top thickness.
Brackets
Cautions
1. The induction hotplate must be installed by qualified personnel or technicians. We have professionals at your service.
Please never conduct the operation by yourself.
2. The hob will not be installed directly above a dishwasher, fridge, freezer, washing machine or clothes dryer, as the
humidity may damage the hob electronics
3. The induction hotplate shall be installed such that better heat radiation can be ensured to enhance its reliability.
4. The wall and induced heating zone above the table surface shall withstand heat.
5. To avoid any damage, the sandwich layer and adhesive must be resistant to heat.
Connecting the hob to the mains power supply
This hob must be connected to the mains power supply only by a suitably qualified person.
Before connecting the hob to the mains power supply, check that:
1. the domestic wiring system is suitable for the power drawn by the hob.
2. the voltage corresponds to the value given in the rating plate
3. the power supply cable sections can withstand the load specified on the rating plate.
To connect the hob to the mains power supply, do not use adapters, reducers, or branching devices, as they can cause
overheating and fire.
The power supply cable must not touch any hot parts and must be positioned so that its temperature will not exceed 75˚C
at any point.
Check with an electrician whether the domestic wiring system is suitable without alterations. Any alterations must only be
made by a qualified electrician.
The power supply should be connected in compliance with the relevant standard,or a single-pole circuit breaker.the method
of connection is shown below.
!
!
WARMING:
Close the cable clamp after making the electrical connection. Close the terminal board cover by twisting it down.
E
D
CONNECTION DIAGRAM
Caution! Voltage of heating elements 220-240V
Caution! In the event of any connection the safety
Wire must be connected to the
E terminal.
④
②
TERMINAL BOARD
⑤
Recommended
type of
connection lead
①
④
Before you install the hob, make sure that
• the work surface is square and level, and no structural members interfere with space requirements
• the work surface is made of a heat-resistant material
• if the hob is installed above an oven, the oven has a built-in cooling fan
• the installation will comply with all clearance requirements and applicable standards and regulations
• a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring,
mounted and positioned to comply with the local wiring rules and regulations.
The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active
[phase] conductors if the local wiring rules allow for this variation of the requirements)
• the isolating switch will be easily accessible to the customer with the hob installed
• you consult local building authorities and by-laws if in doubt regarding installation
• you use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces surrounding the hob.
When you have installed the hob, make sure that
• the power supply cable is not accessible through cupboard doors or drawers
• there is adequate flow of fresh air from outside the cabinetry to the base of the hob
• if the hob is installed above a drawer or cupboard space, a thermal protection barrier is installed below the base of the hob
• the isolating switch is easily accessible by the customer
For 220-240V earthed one-phase connection, bridges
connect L terminals and terminals, safety wire to
L ①
⑤
N
E
• If the cable is damaged or to be replaced, the operation must be carried out the by after-sale agent with dedicated tools to
avoid any accidents.
• If the appliance is being connected directly to the mains an omnipolar circuit-breaker must be installed with a minimum
opening of 3mm between contacts.
• The installer must ensure that the correct electrical connection has been made and that it is compliant with safety
regulations.
• The cable must not be bent or compressed.
• The cable must be checked regularly and replaced by authorised technicians only.
This appliance is labeled in compliance with European directive 2002/96/EC for Waste Electrical and Electronic
Equipment (WEEE). By ensuring that this appliance is disposed of correctly, you will help prevent any possibledamage
to the environment and to human health, which might otherwise be caused if were disposed of in the wrong way.
DISPOSAL: Do not
dispose this product as
unsorted municipal
waste. Collection of
such waste separately
for special treatment is
necessary.
7
②
The symbol on the product indicates that it may not be treated as normal household waste.
It should be taken to a collection point for the recycling of electrical and electronic goods.
This appliance requires specialist waste disposal. For further information regarding the treatment, recover and
recycling of this product please contact your local council, your household waste disposal service, or the shop where
you purchased it.
For more detailed information about treatment, recovery and recycling of this product, please contact your local
cityoffice, your household waste disposal service or the shop where you purchased the product.
8
Download PDF
Similar pages