QuickScan Lite QW2100
TM
General Purpose Corded Handheld
Linear Imager Bar Code Reader
BSR idware GmbH
Jakob-Haringer-Str.3
A-5020 Salzburg
Web: www.bsr.at
Product Reference Guide
Datalogic ADC, Inc.
959 Terry Street
Eugene, OR 97402
USA
Telephone: (541) 683-5700
Fax: (541) 345-7140
©2011-2014 Datalogic ADC, Inc.
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described
therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic
ADC, Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic ADC"). Owners of Datalogic products are hereby
granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative. Electronic versions may either be downloadable from the Datalogic website (www.datalogic.com) or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this or
other Datalogic publications, please let us know via the "Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A.
and the E.U. All other brand and product names may be trademarks of their respective owners.
QuickScan is a registered trademark of Datalogic ADC, Inc. in many countries, including the U.S.A. and the E.U. Autosense is a registered trademark of Datalogic ADC, Inc. in the U.S.
This product may be covered by one or more of the following patents:
Design Patents: CN ZL201230049587.7; EP1987843; USD677258.
Utility Patents: EP0789315B1; EP1128315B1; EP1396811B1; EP1413971B1; US5481098; US5992740; US6098883; US6454168;
US6561427; US6758403; US6808114; US6997385; US7387246; US7506816.
Additional Patents Pending
Table of Contents
Chapter 1. Introduction.................................................................................................................................................................... 1
About this Guide .....................................................................................................................................................................................................................1
Manual Overview ....................................................................................................................................................................................................................1
Manual Conventions ..............................................................................................................................................................................................................2
References .................................................................................................................................................................................................................................2
Technical Support ...................................................................................................................................................................................................................3
Datalogic Website Support .......................................................................................................................................................................................3
Reseller Technical Support ........................................................................................................................................................................................3
Telephone Technical Support ..................................................................................................................................................................................3
Chapter 2. Getting Started............................................................................................................................................................... 5
About the Reader ....................................................................................................................................................................................................................5
Unpacking .................................................................................................................................................................................................................................5
Setting Up the Reader ...........................................................................................................................................................................................................6
Install the Interface Cable ..........................................................................................................................................................................................6
Hands Free Stand ..........................................................................................................................................................................................................7
Programming .................................................................................................................................................................................................................8
Using the Programming Bar Codes ........................................................................................................................................................................9
Select the Interface Type ............................................................................................................................................................................................9
Configure Interface Settings .....................................................................................................................................................................................9
Configure Other Features ..........................................................................................................................................................................................9
Software Version Transmission ............................................................................................................................................................................. 10
Resetting the Product Configuration to Defaults ................................................................................................................................................... 10
Chapter 3. Interfaces ...................................................................................................................................................................... 11
Interface Selection ............................................................................................................................................................................................................... 11
Configuring the Interface ................................................................................................................................................................................................. 11
Global Interface Features .................................................................................................................................................................................................. 15
Host Commands — Obey/Ignore ........................................................................................................................................................................ 15
USB Suspend Mode ................................................................................................................................................................................................... 16
Chapter 4. General Features .......................................................................................................................................................... 17
Double Read Timeout ........................................................................................................................................................................................................ 17
Label Gone Timeout ........................................................................................................................................................................................................... 19
Power Save Mode ................................................................................................................................................................................................................ 20
Sleep Mode Timeout .......................................................................................................................................................................................................... 21
LED and Beeper Indicators ............................................................................................................................................................................................... 22
Power On Alert ............................................................................................................................................................................................................ 22
Good Read: When to Indicate ................................................................................................................................................................................ 23
Good Read Beep Type .............................................................................................................................................................................................. 24
Good Read Beep Frequency ................................................................................................................................................................................... 25
Good Read Beep Length .......................................................................................................................................................................................... 25
Illumination Control .................................................................................................................................................................................................. 27
Good Read Beep Volume ........................................................................................................................................................................................ 28
Good Read LED Duration ........................................................................................................................................................................................ 29
Scanning Features ............................................................................................................................................................................................................... 30
Scan Mode .................................................................................................................................................................................................................... 30
Stand Mode Triggered Timeout ........................................................................................................................................................................... 31
Scanning Active Time ............................................................................................................................................................................................... 33
Stand Mode Flash ....................................................................................................................................................................................................... 33
Flash On Time .............................................................................................................................................................................................................. 34
Product Reference Guide
1
Flash Off Time ...............................................................................................................................................................................................................34
Stand Mode Sensitivity .............................................................................................................................................................................................35
Green Spot Duration ...........................................................................................................................................................................................................36
Chapter 5. RS-232 ONLY Interface ................................................................................................................................................. 37
Introduction ...........................................................................................................................................................................................................................37
RS-232 Standard Factory Settings ..................................................................................................................................................................................37
Baud Rate ................................................................................................................................................................................................................................37
Data Bits ...................................................................................................................................................................................................................................39
Stop Bits ...................................................................................................................................................................................................................................39
Parity .........................................................................................................................................................................................................................................40
Handshaking Control ..........................................................................................................................................................................................................41
Chapter 6. RS-232/USB-Com Interfaces......................................................................................................................................... 43
Introduction ...........................................................................................................................................................................................................................43
Standard Factory Settings .................................................................................................................................................................................................43
Intercharacter Delay ............................................................................................................................................................................................................44
Beep On ASCII BEL ................................................................................................................................................................................................................45
Beep On Not on File .............................................................................................................................................................................................................45
ACK NAK Options ..................................................................................................................................................................................................................46
ACK Character ..............................................................................................................................................................................................................47
NAK Character ..............................................................................................................................................................................................................47
ACK NAK Timeout Value ...........................................................................................................................................................................................48
ACK NAK Retry Count ................................................................................................................................................................................................49
ACK NAK Error Handling ...........................................................................................................................................................................................50
Indicate Transmission Failure ...........................................................................................................................................................................................51
Disable Character .................................................................................................................................................................................................................51
Enable Character ...................................................................................................................................................................................................................52
Chapter 7. Keyboard Interface ....................................................................................................................................................... 53
Introduction ...........................................................................................................................................................................................................................53
Standard Factory Settings .................................................................................................................................................................................................53
Scancode Tables ...................................................................................................................................................................................................................53
Country Mode ........................................................................................................................................................................................................................54
Caps Lock State .....................................................................................................................................................................................................................57
Numlock ...................................................................................................................................................................................................................................58
Keyboard Numeric Keypad ...............................................................................................................................................................................................58
Keyboard Send Control Characters ................................................................................................................................................................................59
Wedge Quiet Interval ..........................................................................................................................................................................................................60
Intercharacter Delay ............................................................................................................................................................................................................61
Intercode Delay .....................................................................................................................................................................................................................62
USB Keyboard Speed ...........................................................................................................................................................................................................63
Chapter 8. USB-OEM Interface ....................................................................................................................................................... 65
Introduction ...........................................................................................................................................................................................................................65
Standard Factory Settings .................................................................................................................................................................................................65
USB-OEM Device Usage .....................................................................................................................................................................................................66
USB-OEM Interface Options ..............................................................................................................................................................................................66
Chapter 9. Data Editing................................................................................................................................................................... 67
Data Editing Overview ........................................................................................................................................................................................................67
Please Keep In Mind... .........................................................................................................................................................................................................68
Global Prefix/Suffix ..............................................................................................................................................................................................................68
Global AIM ID .........................................................................................................................................................................................................................69
GS1-128 AIM ID .....................................................................................................................................................................................................................69
Label ID ....................................................................................................................................................................................................................................70
Label ID: Pre-loaded Sets .........................................................................................................................................................................................70
Label ID: Set Individually Per Symbology ..........................................................................................................................................................71
Label ID Control ...........................................................................................................................................................................................................71
2
QuickScanTM Lite QW2100
Label ID Symbology Selection ............................................................................................................................................................................... 72
Set Global Mid Label ID Character(s) ............................................................................................................................................................................ 80
Case Conversion ................................................................................................................................................................................................................... 81
Character Conversion ......................................................................................................................................................................................................... 82
Chapter 10. Symbologies............................................................................................................................................................... 83
Introduction ........................................................................................................................................................................................................................... 83
Symbologies ................................................................................................................................................................................................................ 83
Standard Factory Settings for Symbologies ............................................................................................................................................................... 83
Disable All Symbologies .................................................................................................................................................................................................... 84
Coupon Control .................................................................................................................................................................................................................... 84
UPC-A ....................................................................................................................................................................................................................................... 85
UPC-A Enable/Disable .............................................................................................................................................................................................. 85
UPC-A Check Character Transmission ................................................................................................................................................................ 85
Expand UPC-A to EAN-13 ........................................................................................................................................................................................ 86
UPC-A Number System Character Transmission ............................................................................................................................................ 86
In-Store Minimum Reads ......................................................................................................................................................................................... 87
UPC-E ........................................................................................................................................................................................................................................ 88
UPC-E Enable/Disable ............................................................................................................................................................................................... 88
UPC-E Check Character Transmission ................................................................................................................................................................. 88
Expand UPC-E to EAN-13 ......................................................................................................................................................................................... 89
Expand UPC-E to UPC-A ........................................................................................................................................................................................... 89
UPC-E Number System Character Transmission ............................................................................................................................................. 90
UPC-E Minimum Reads ............................................................................................................................................................................................ 90
EAN 13 ...................................................................................................................................................................................................................................... 91
EAN 13 Enable/Disable ............................................................................................................................................................................................. 91
EAN 13 Check Character Transmission ............................................................................................................................................................... 91
EAN-13 Flag 1 Character .......................................................................................................................................................................................... 92
EAN-13 ISBN Conversion ......................................................................................................................................................................................... 92
ISSN Enable/Disable .................................................................................................................................................................................................. 93
EAN 13 Minimum Reads .......................................................................................................................................................................................... 93
EAN 8 ........................................................................................................................................................................................................................................ 94
EAN 8 Enable/Disable ............................................................................................................................................................................................... 94
EAN 8 Check Character Transmission ................................................................................................................................................................. 94
Expand EAN 8 to EAN 13 ......................................................................................................................................................................................... 95
EAN 8 Both Guards Substitution ........................................................................................................................................................................... 95
EAN 8 Guard Insertion .............................................................................................................................................................................................. 96
EAN 8 Guard Substitution ....................................................................................................................................................................................... 96
EAN 8 Minimum Segment Length Block ........................................................................................................................................................... 97
EAN 8 Minimum Reads ............................................................................................................................................................................................. 99
EAN 8 Stitch Exact Label Halves .......................................................................................................................................................................... 100
EAN 8 Stitch Unlike Label Halves ........................................................................................................................................................................ 100
EAN Two Label .................................................................................................................................................................................................................... 101
EAN Two Label Enable/Disable ........................................................................................................................................................................... 101
EAN Two Label Combined Transmission ......................................................................................................................................................... 101
EAN Two Label Minimum Reads ......................................................................................................................................................................... 102
UPC/EAN Global Settings ................................................................................................................................................................................................ 103
UPC/EAN Decoding Level ..................................................................................................................................................................................... 103
UPC/EAN Correlation .............................................................................................................................................................................................. 104
UPC/EAN Price Weight Check .............................................................................................................................................................................. 105
UPC-A Minimum Reads .......................................................................................................................................................................................... 106
UPC/EAN Guard Insertion ..................................................................................................................................................................................... 107
UPC/EAN Stitch Exact Label Halves ................................................................................................................................................................... 107
UPC/EAN Stitch Unlike Label Halves ................................................................................................................................................................. 108
UPC/EAN Minimum Segment Length ............................................................................................................................................................... 109
Add-Ons ................................................................................................................................................................................................................................ 111
Optional Add-ons ..................................................................................................................................................................................................... 111
Optional Add-On Timer ......................................................................................................................................................................................... 113
P2 Add-Ons Minimum Reads ............................................................................................................................................................................... 115
Product Reference Guide
3
P5 Add-Ons Minimum Reads ............................................................................................................................................................................... 116
GS1-128 Add-Ons Minimum Reads ................................................................................................................................................................... 117
GS1 DataBarTM Omnidirectional ................................................................................................................................................................................... 118
GS1 DataBar Omnidirectional Enable/Disable .............................................................................................................................................. 118
GS1 DataBar Omnidirectional GS1-128 Emulation ...................................................................................................................................... 118
GS1 DataBar Omnidirectional Minimum Reads ............................................................................................................................................ 119
GS1 DataBarTM Expanded ............................................................................................................................................................................................... 120
GS1 DataBar Expanded Enable/Disable ........................................................................................................................................................... 120
GS1 DataBar Expanded GS1-128 Emulation .................................................................................................................................................. 120
GS1 DataBar Expanded Minimum Reads ........................................................................................................................................................ 121
GS1 DataBar Expanded Length Control .......................................................................................................................................................... 122
GS1 DataBar Expanded Set Length 1 ................................................................................................................................................................ 123
GS1 DataBar Expanded Set Length 2 ................................................................................................................................................................ 124
GS1 DataBarTM Limited .................................................................................................................................................................................................... 125
GS1 DataBar Limited Enable/Disable ............................................................................................................................................................... 125
GS1 DataBar Limited GS1-128 Emulation ....................................................................................................................................................... 125
GS1 DataBar Limited Minimum Reads ............................................................................................................................................................. 126
Code 39 ................................................................................................................................................................................................................................. 127
Code 39 Enable/Disable ........................................................................................................................................................................................ 127
Code 39 Check Character Calculation .............................................................................................................................................................. 128
Code 39 Check Character Transmission .......................................................................................................................................................... 129
Code 39 Start/Stop Character Transmission .................................................................................................................................................. 129
Code 39 Full ASCII .................................................................................................................................................................................................... 130
Code 39 Quiet Zones .............................................................................................................................................................................................. 131
Code 39 Minimum Reads ...................................................................................................................................................................................... 132
Code 39 Decoding Level ....................................................................................................................................................................................... 133
Code 39 Length Control ........................................................................................................................................................................................ 134
Code 39 Set Length 1 ............................................................................................................................................................................................. 135
Code 39 Set Length 2 ............................................................................................................................................................................................. 136
Code 39 Interdigit Ratio ........................................................................................................................................................................................ 137
Code 39 Character Correlation ........................................................................................................................................................................... 139
Code 39 Stitching .................................................................................................................................................................................................... 139
Code 32 (Italian Pharmaceutical) ................................................................................................................................................................................. 140
Code 32 Enable/Disable ........................................................................................................................................................................................ 140
Code 32 Feature Setting Exceptions ................................................................................................................................................................. 140
Code 32 Check Character Transmission .......................................................................................................................................................... 141
Code 32 Start/Stop Character Transmission .................................................................................................................................................. 141
Code 39 CIP (French Pharmaceutical) ........................................................................................................................................................................ 142
Code 39 CIP Enable/Disable ................................................................................................................................................................................. 142
Code 128 ............................................................................................................................................................................................................................... 142
Code 128 Enable/Disable ...................................................................................................................................................................................... 142
Expand Code 128 to Code 39 ............................................................................................................................................................................. 143
Code 128 Check Character Transmission ........................................................................................................................................................ 143
Code 128 Function Character Transmission .................................................................................................................................................. 144
Code 128 Sub-Code Change Transmission .................................................................................................................................................... 144
Code 128 Quiet Zones ............................................................................................................................................................................................ 145
Code 128 Minimum Reads ................................................................................................................................................................................... 146
Code 128 Decoding Level ..................................................................................................................................................................................... 147
Code 128 Length Control ...................................................................................................................................................................................... 148
Code 128 Set Length 1 ........................................................................................................................................................................................... 149
Code 128 Set Length 2 ........................................................................................................................................................................................... 150
Code 128 Character Correlation ......................................................................................................................................................................... 151
Code 128 Stitching .................................................................................................................................................................................................. 151
GS1-128 ................................................................................................................................................................................................................................. 152
GS1-128 Enable ........................................................................................................................................................................................................ 152
Interleaved 2 of 5 (I 2 of 5) .............................................................................................................................................................................................. 153
I 2 of 5 Enable/Disable ............................................................................................................................................................................................ 153
I 2 of 5 Check Character Calculation ................................................................................................................................................................. 154
I 2 of 5 Check Character Transmission .............................................................................................................................................................. 155
I 2 of 5 Minimum Reads ......................................................................................................................................................................................... 156
4
QuickScanTM Lite QW2100
I 2 of 5 Decoding Level ........................................................................................................................................................................................... 157
I 2 of 5 Length Control ............................................................................................................................................................................................ 158
I 2 of 5 Set Length 1 ................................................................................................................................................................................................. 159
I 2 of 5 Set Length 2 ................................................................................................................................................................................................. 160
I 2 of 5 Character Correlation ............................................................................................................................................................................... 161
I 2 of 5 Zero Pattern ................................................................................................................................................................................................. 161
I 2 of 5 Stitching ........................................................................................................................................................................................................162
Interleaved 2 of 5 CIP HR ................................................................................................................................................................................................. 162
Interleaved 2 of 5 CIP HR Enable/Disable ........................................................................................................................................................ 162
Datalogic 2 of 5 ................................................................................................................................................................................................................... 163
Datalogic 2 of 5 Enable/Disable .......................................................................................................................................................................... 163
Datalogic 2 of 5 Check Character Calculation ................................................................................................................................................ 164
Datalogic 2 of 5 Check Character Transmission ............................................................................................................................................ 164
Datalogic 2 of 5 Minimum Reads ....................................................................................................................................................................... 165
Datalogic 2 of 5 Decoding Level ......................................................................................................................................................................... 165
Datalogic 2 of 5 Length Control .......................................................................................................................................................................... 166
Datalogic 2 of 5 Set Length 1 ............................................................................................................................................................................... 167
Datalogic 2 of 5 Set Length 2 ............................................................................................................................................................................... 168
Datalogic 2 of 5 Interdigit Maximum Ratio ..................................................................................................................................................... 169
Datalogic 2 of 5 Character Correlation ............................................................................................................................................................. 171
Datalogic 2 of 5 Stitching ...................................................................................................................................................................................... 171
Codabar ................................................................................................................................................................................................................................. 172
Codabar Enable/Disable ........................................................................................................................................................................................ 172
Codabar Check Character Calculation .............................................................................................................................................................. 172
Codabar Check Character Transmission .......................................................................................................................................................... 173
Codabar Start/Stop Character Transmission .................................................................................................................................................. 173
Codabar Start/Stop Character Set ...................................................................................................................................................................... 174
Codabar Start/Stop Character Match ................................................................................................................................................................ 175
Codabar Quiet Zones .............................................................................................................................................................................................. 176
Codabar Minimum Reads ...................................................................................................................................................................................... 177
Codabar Decoding Level ....................................................................................................................................................................................... 178
Codabar Length Control ........................................................................................................................................................................................ 179
Codabar Set Length 1 ............................................................................................................................................................................................. 180
Codabar Set Length 2 ............................................................................................................................................................................................. 181
Codabar Interdigit Ratio ........................................................................................................................................................................................ 182
Codabar Character Correlation ........................................................................................................................................................................... 184
Codabar Stitching .................................................................................................................................................................................................... 184
ABC Codabar ........................................................................................................................................................................................................................ 185
ABC Codabar Enable/Disable ............................................................................................................................................................................... 185
ABC Codabar Concatenation Mode .................................................................................................................................................................. 185
ABC Codabar Dynamic Concatenation Timeout .......................................................................................................................................... 186
ABC Codabar Force Concatenation ................................................................................................................................................................... 187
Code 11 .................................................................................................................................................................................................................................. 187
Code 11 Enable/Disable ......................................................................................................................................................................................... 187
Code 11 Check Character Calculation .............................................................................................................................................................. 188
Code 11 Check Character Transmission ........................................................................................................................................................... 188
Code 11 Minimum Reads ...................................................................................................................................................................................... 189
Code 11 Length Control ........................................................................................................................................................................................ 190
Code 11 Set Length 1 .............................................................................................................................................................................................. 191
Code 11 Set Length 2 .............................................................................................................................................................................................. 192
Code 11 Interdigit Ratio ......................................................................................................................................................................................... 193
Code 11 Decoding Level ........................................................................................................................................................................................ 195
Code 11 Character Correlation ............................................................................................................................................................................ 196
Code 11 Stitching ..................................................................................................................................................................................................... 196
Standard 2 of 5 .................................................................................................................................................................................................................... 197
Standard 2 of 5 Enable/Disable ........................................................................................................................................................................... 197
Standard 2 of 5 Check Character Calculation ................................................................................................................................................ 197
Standard 2 of 5 Check Character Transmission ............................................................................................................................................. 198
Standard 2 of 5 Minimum Reads ........................................................................................................................................................................ 198
Standard 2 of 5 Decoding Level .......................................................................................................................................................................... 199
Product Reference Guide
5
Standard 2 of 5 Length Control .......................................................................................................................................................................... 199
Standard 2 of 5 Set Length 1 ............................................................................................................................................................................... 200
Standard 2 of 5 Set Length 2 ............................................................................................................................................................................... 201
Standard 2 of 5 Character Correlation .............................................................................................................................................................. 202
Standard 2 of 5 Stitching ....................................................................................................................................................................................... 202
Industrial 2 of 5 ................................................................................................................................................................................................................... 203
Industrial 2 of 5 Enable/Disable .......................................................................................................................................................................... 203
Industrial 2 of 5 Check Character Calculation ................................................................................................................................................ 203
Industrial 2 of 5 Check Character Transmission ............................................................................................................................................ 204
Industrial 2 of 5 Length Control .......................................................................................................................................................................... 204
Industrial 2 of 5 Set Length 1 ............................................................................................................................................................................... 205
Industrial 2 of 5 Set Length 2 ............................................................................................................................................................................... 206
Industrial 2 of 5 Minimum Reads ........................................................................................................................................................................ 207
Industrial 2 of 5 Stitching ...................................................................................................................................................................................... 208
Industrial 2 of 5 Character Correlation ............................................................................................................................................................. 208
IATA ........................................................................................................................................................................................................................................ 209
IATA Enable/Disable ............................................................................................................................................................................................... 209
IATA Check Character Transmission ................................................................................................................................................................. 209
ISBT 128 ................................................................................................................................................................................................................................. 210
ISBT 128 Concatenation ........................................................................................................................................................................................ 210
ISBT 128 Concatenation Mode ............................................................................................................................................................................ 210
ISBT 128 Dynamic Concatenation Timeout .................................................................................................................................................... 211
ISBT 128 Force Concatenation ............................................................................................................................................................................ 212
ISBT 128 Advanced Concatenation Options .................................................................................................................................................. 212
MSI .......................................................................................................................................................................................................................................... 213
MSI Enable/Disable ................................................................................................................................................................................................. 213
MSI Check Character Calculation ....................................................................................................................................................................... 213
MSI Check Character Transmission ................................................................................................................................................................... 214
MSI Length Control ................................................................................................................................................................................................. 214
MSI Set Length 1 ...................................................................................................................................................................................................... 215
MSI Set Length 2 ...................................................................................................................................................................................................... 216
MSI Minimum Reads ............................................................................................................................................................................................... 217
MSI Decoding Level ................................................................................................................................................................................................ 218
Code 93 ................................................................................................................................................................................................................................. 219
Code 93 Enable/Disable ........................................................................................................................................................................................ 219
Code 93 Check Character Calculation .............................................................................................................................................................. 219
Code 93 Check Character Transmission .......................................................................................................................................................... 220
Code 93 Length Control ........................................................................................................................................................................................ 220
Code 93 Set Length 1 ............................................................................................................................................................................................. 221
Code 93 Set Length 2 ............................................................................................................................................................................................. 222
Code 93 Minimum Reads ...................................................................................................................................................................................... 223
Code 93 Decoding Level ....................................................................................................................................................................................... 224
Code 93 Quiet Zones .............................................................................................................................................................................................. 225
Code 93 Stitching .................................................................................................................................................................................................... 226
Code 93 Character Correlation ........................................................................................................................................................................... 226
Codablock F ......................................................................................................................................................................................................................... 227
Codablock F Enable/Disable ................................................................................................................................................................................ 227
Codablock F EAN Enable/Disable ...................................................................................................................................................................... 227
Codablock F AIM Check ......................................................................................................................................................................................... 228
Codablock F Length Control ................................................................................................................................................................................ 228
Codablock F Set Length 1 ..................................................................................................................................................................................... 229
Codablock F Set Length 2 ..................................................................................................................................................................................... 230
Code 4 .................................................................................................................................................................................................................................... 231
Code 4 Enable/Disable ........................................................................................................................................................................................... 231
Code 4 Check Character Transmission ............................................................................................................................................................. 231
Code 4 Hex to Decimal Conversion ................................................................................................................................................................... 232
Code 5 .................................................................................................................................................................................................................................... 232
Code 5 Enable/Disable ........................................................................................................................................................................................... 232
Code 5 Check Character Transmission ............................................................................................................................................................. 233
Code 5 Hex to Decimal Conversion ................................................................................................................................................................... 233
6
QuickScanTM Lite QW2100
Code 4 and Code 5 Common Configuration Items ............................................................................................................................................... 234
Code 4 and 5 Decoding Level .............................................................................................................................................................................. 234
Code 4 and Code 5 Minimum Reads ................................................................................................................................................................. 235
Follett 2 of 5 ......................................................................................................................................................................................................................... 236
Follett 2 of 5 Enable/Disable ................................................................................................................................................................................ 236
BC412 ..................................................................................................................................................................................................................................... 236
BC412 Enable/Disable ............................................................................................................................................................................................ 236
BC412 Check Character Calculation .................................................................................................................................................................. 237
BC412 Minimum Reads .......................................................................................................................................................................................... 238
BC412 Decoding Level ........................................................................................................................................................................................... 239
BC412 Length Control ............................................................................................................................................................................................ 240
BC412 Set Length 1 ................................................................................................................................................................................................. 241
BC412 Set Length 2 ................................................................................................................................................................................................. 242
Chapter 11. References ................................................................................................................................................................ 243
Label Gone Timeout .........................................................................................................................................................................................................244
Good Read LED Duration ................................................................................................................................................................................................ 245
Scan Mode ............................................................................................................................................................................................................................ 246
Scanning Active Time .......................................................................................................................................................................................................247
Flash On Time ...................................................................................................................................................................................................................... 248
Flash Off Time ...................................................................................................................................................................................................................... 249
Intercharacter Delay .........................................................................................................................................................................................................250
ACK Character ..................................................................................................................................................................................................................... 251
NAK Character ..................................................................................................................................................................................................................... 252
ACK NAK Timeout Value .................................................................................................................................................................................................. 253
ACK NAK Retry Count .......................................................................................................................................................................................................254
Disable Character ............................................................................................................................................................................................................... 255
Enable Character ................................................................................................................................................................................................................ 256
Wedge Quiet Interval .......................................................................................................................................................................................................257
Intercharacter Delay .........................................................................................................................................................................................................258
Intercode Delay .................................................................................................................................................................................................................. 259
Global Prefix/Suffix ............................................................................................................................................................................................................ 260
Example: Setting a Prefix ....................................................................................................................................................................................... 260
Global AIM ID ....................................................................................................................................................................................................................... 261
Label ID: Pre-loaded Sets ................................................................................................................................................................................................ 262
Label ID: Set Individually Per Symbology ................................................................................................................................................................. 264
Character Conversion .......................................................................................................................................................................................................266
Decoding Levels ................................................................................................................................................................................................................. 267
Set Length 1 ......................................................................................................................................................................................................................... 268
Set Length 2 ......................................................................................................................................................................................................................... 269
Appendix A. Technical Specifications ..................................................................................... 271
Standard Cable Pinouts ................................................................................................................................................................................................... 273
Appendix B. Standard Defaults............................................................................................... 275
Default Exceptions ............................................................................................................................................................................................................ 285
Appendix C. LED and Beeper Indications................................................................................ 289
LED and Beeper Indications ........................................................................................................................................................................................... 290
Error Codes ........................................................................................................................................................................................................................... 291
Appendix D. Sample Bar Codes............................................................................................... 293
Interleaved 2 of 5 ...........................................................................................................................................................................................................293
Codabar ............................................................................................................................................................................................................................ 294
Code 11 ............................................................................................................................................................................................................................ 294
GS1 DataBar (RSS) .............................................................................................................................................................................................................. 295
GS1 DataBar-14 .........................................................................................................................................................................................................295
Product Reference Guide
7
Appendix E. Keypad ............................................................................................................... 297
Appendix F. Scancode Tables ................................................................................................. 301
Control Character Emulation ......................................................................................................................................................................................... 301
Interface Type PC AT PS/2 or USB-Keyboard ........................................................................................................................................................... 302
Interface type PC AT PS/2 Alt Mode or USB-Keyboard Alt Mode ..................................................................................................................... 304
Digital Interface .................................................................................................................................................................................................................. 306
IBM XT .................................................................................................................................................................................................................................... 308
Microsoft Windows Codepage 1252 .......................................................................................................................................................................... 310
Index ..................................................................................................................... 311
8
QuickScanTM Lite QW2100
Chapter 1
Introduction
About this Guide
This Product Reference Guide (PRG) is provided for users seeking advanced technical
information, including connection, programming, maintenance and specifications. The
Quick Reference Guide (QRG) and other publications associated with this product are
downloadable free of charge from the website listed on the back cover of this manual.
Typically, units are factory-programmed for the most common terminal and communications settings. If you need to modify any programmable settings, custom configuration
can be accomplished by scanning the programming bar codes within this guide.
Programming can alternatively be performed using the Datalogic Aladdin™ Configuration application which is downloadable from the Datalogic website listed on the back
cover of this manual. This multi-platform utility program allows device configuration using a PC. It communicates to the device using a serial or USB cable and can also create
configuration bar codes to print.
Manual Overview
Chapter 1, Introduction provides a product overview, unpacking instructions, and cable
connection information.
Chapter 2, Getting Started presents information about unpacking and setting up the
reader.
Chapter 3, Interfaces consists of interface configuration bar codes and details.
Chapter 4, General Features includes programming bar codes for selecting common
features for the reader and general use bar codes to customize how the data is transmitted
to the host device.
Chapter 5, RS-232 ONLY Interface supplies information about setting up the reader for
RS-232 operation.
Chapter 6, RS-232/USB-Com Interfaces features information about options involving
both the RS-232 and USB-Com interfaces.
Chapter 7, Keyboard Interface discusses how to set up the reader for Keyboard Wedge
operation.
Chapter 8, USB-OEM Interface explains how to set the reader up for USB operation.
Chapter 9, Data Editing offers advanced configuration options for customization of
scanned data output.
Chapter 10, Symbologies defines options for all symbologies and provides the program-
Product Reference Guide
1
Introduction
ming bar codes necessary for configuring these features.
Chapter 11, References provides details concerning programmable features.
Appendix A, Technical Specifications lists physical and performance characteristics, as
well as environmental and regulatory specifications. It also provides standard cable pinouts.
Appendix B, Standard Defaults references common factory default settings for reader
features and options.
Appendix C, LED and Beeper Indications supplies tables containing descriptions of the
functions and behaviors of the reader’s LED and Beeper indicators.
Appendix D, Sample Bar Codes offers sample bar codes of several common symbologies.
Appendix E, Keypad includes numeric bar codes to be scanned for certain parameter settings.
Appendix F, Scancode Tables lists control character emulation information for Wedge
and USB Keyboard interfaces.
Manual Conventions
The following conventions are used in this document:
The symbols listed below are used in this manual to notify the reader of key issues or
procedures that must be observed when using the reader:
Notes contain information necessary for properly diagnosing,
repairing and operating the reader.
NOTE
The CAUTION symbol advises you of actions that could damage equipment or property.
CAUTION
References
Current versions of the Product Reference Guide (PRG), Quick Reference Guide
(QRG), the Datalogic Aladdin™ Configuration application, software/firmware and any
additional manuals, instruction sheets and utilities for this product can be downloaded
from the website listed on the back cover of this manual. Alternatively, printed copies or
product support CDs can be purchased through your Datalogic reseller.
2
QuickScanTM Lite QW2100
Technical Support
Technical Support
Datalogic Website Support
The Datalogic website (www.datalogic.com) is the complete source for technical support and information for Datalogic products. The site offers product support, warranty
information, product manuals, product tech notes, software updates, demos, and instructions for returning products for repair.
Reseller Technical Support
An excellent source for technical assistance and information is an authorized Datalogic
reseller. A reseller is acquainted with specific types of businesses, application software,
and computer systems and can provide individualized assistance.
Telephone Technical Support
If you do not have internet or email access, you may contact Datalogic technical support
at (541) 349-8283 or check the back cover of your manual for more contact information.
Product Reference Guide
3
Introduction
NOTES
4
QuickScanTM Lite QW2100
Chapter 2
Getting Started
About the Reader
One distinctive feature offered by the reader is a very wide scan angle which can read long
linearbar codes, such as utlity bills. Whether used in Single Trigger or Continuous Mode,
the ergonomic design of the reader will help to promote comfortable handling during extended periods of use.
The reader can communicate using the following interfaces:
RS-232 — The
reader can communicate with a standard or Wincor-Nixdorf (W-N) RS-
232 host.
RS-232 OPOS — This
interface is used for OPOS/UPOS/JavaPOS systems.
Keyboard Wedge (KBW) — When connected using this interface, the host interprets scanned
data as keystrokes and supports several international keyboards (for the Windows® environment). See Country Mode on page 54 for a full listing.
USB — Select to communicate either by USB OEM, USB COM STD, or USB Keyboard
interface types by scanning the appropriate interface type bar codes available in this manual. The default interface is USB-KBD for Wedge models (7230) and USB-OEM for
IBM models (7210).
Unpacking
Check carefully to ensure the reader and any accessories ordered are present and undamaged. If any damage occurred during shipment, contact Technical Support on page 3.
KEEP THE PACKAGING. Should the unit ever require service, it should be returned
in its original shipping container.
Product Reference Guide
5
Getting Started
Setting Up the Reader
Follow the steps provided in this section to connect and get your reader up and communicating with its host:
1. Install the Interface Cable
2. Select the Interface Type
3. Configure Interface Settings (only if not using factory settings for that interface)
4. Configure Other Features (if modifications are needed from factory settings)
Install the Interface Cable
The reader kit you ordered to match your interface should provide a compatible cable for
your installation. If not, contact Technical Support.
Seat the cable assembly into the reader, aligning both the connector, aligning the cable
clip with its opening as shown in the insert portion of Figure 1.
RS-232 Serial Connection — Turn
off power to the terminal/PC and connect the reader to
the terminal/PC serial port via the RS-232 cable as shown in Figure 1. If the terminal
will not support POT (Power Off the Terminal) to supply reader power, use the approved power supply (AC Adapter). Plug the AC Adapter barrel connector into the socket on the RS-232 cable connector and the AC Adapter plug into a standard power outlet.
Figure 1. Connecting the Interface Cable/RS-232 Connection
Connecting at
the Reader
Bottom of Imager
Cable
Interface Cable Port
Cable Strain Relief
To Host
Cable Clip (Latch)
Disconnecting at
the Reader
Insert a paperclip
into this hole to
release the
cable latch
Strain Relief
Cable
Other connection types are described below and illustrated in Figure 2.
6
QuickScanTM Lite QW2100
Setting Up the Reader
USB Connection — Connect the reader to a USB port on the terminal/PC using the correct
USB cable for the interface type you ordered. Reference Figure 2.
Keyboard Wedge Connection — The
Keyboard Wedge cable has a ‘Y’ connection from the
reader. Connect the female to the male end from the keyboard and the remaining end at
the keyboard port at the terminal/PC. Reference Figure 2.
B
Figure 2. Other Interface Connections
US
Ke W
M
or...
IB
NOTE
yb
ed oard
ge
or...
Specific cables are required for connection to different hosts.
The connectors illustrated above are examples only. Actual
connectors may vary from those illustrated, but the steps to
connect the reader remain the same.
Hands Free Stand
An accessory is available which holds the reader at a convenient angle, allowing hands
free scanning of items. Press in on the release buttons on both sides of the stand to raise
the arm of the stand as shown in Figure 4. The stand can optionally be attached to a
counter or table using self-tapping screws or double-sided tape.
Figure 3. Adjusting the Stand Arm
Optional
a
Product Reference Guide
b
c
7
Getting Started
Hands Free Stand — continued
The holder cup can be positioned in any of the three angles shown in Figure 4. Grasp
the holder cup as indicated and rotate to the desired position.
Refer to Scan Mode on page 30 for information about programming the reader for use
with the stand.
Figure 4. Adjusting the Stand
This accessory can also be used as a holder to mount the reader on a wall or other vertical
position as shown in Figure 5.
Figure 5. Using the Wall Holder
Programming
The reader is typically factory-configured with a set of default features standard to the
interface type you ordered. After scanning the interface bar code from the Interfaces section, you can select other options and customize your reader through use of the instructions and programming bar codes available in the corresponding features section for your
interface and also the Data Editing and Symbologies chapters of this manual.
8
QuickScanTM Lite QW2100
Setting Up the Reader
Using the Programming Bar Codes
This manual contains feature descriptions and bar codes which allow you to reconfigure
your reader. Some programming bar code labels, like Resetting the Product Configuration to Defaults on page 10, require only the scan of that single label to enact the change.
Most of the programming labels in this manual, however, require the reader to be placed
in Programming Mode prior to scanning them. Scan an ENTER/EXIT bar code once to
enter Programming Mode. Once the reader is in Programming Mode, you can scan a
number of parameter settings before scanning the ENTER/EXIT bar code a second time,
which will then accept your changes, exit Programming Mode and return the reader to
normal operation.
NOTE
There are some exceptions to the typical programming
sequence described above. Please read the description and
setting instructions carefully when configuring each given programmable feature.
Select the Interface Type
Upon completing the physical connection between the reader and its host, proceed directly to Interfaces on page 11 for information and programming for the interface type
the reader is connected to (for example: RS-232, Keyboard Wedge, USB, etc.) and scan
the appropriate bar code in that section to select your system’s correct interface type.
Configure Interface Settings
The reader is typically factory-configured with a set of default features standard to the
interface type you ordered. If after scanning the interface bar code from the Interfaces
section, your installation requires you to select options to further customize your reader,
turn to the appropriate section for your interface type as listed below:
•
RS-232 ONLY Interface, starting on page 37
•
RS-232/USB-Com Interfaces, starting on page 43
•
Keyboard Interface, starting on page 53
•
USB-OEM Interface, starting on page 65
Configure Other Features
If your installation requires different programming than the standard factory default settings, the following sections of this manual allow configuration of non-interface-specific
settings you might require:
General Features — General Features includes programming for scanning, beeper and
LED indicators and other such universal settings.
Symbologies — Includes options concerning the bar code label types (symbologies). These
settings allow you to enable/disable symbologies, set label lengths, require check digit,
etc.
Product Reference Guide
9
Getting Started
Software Version Transmission
The software version of the device can be transmitted over the RS-232 and Keyboard interfaces by scanning the following label.
Transmit Software Version
Resetting the Product Configuration to Defaults
If you aren't sure what programming options are in your reader, or you've changed some
options and want to restore the Custom Default Configuration that may have been saved
in the reader, scan the Restore Custom Default Configuration bar code below. This will
restore the custom configuration for the currently active interface.
Custom defaults are based on the interface type. Configure
the reader for the correct interface before scanning this label.
NOTE
Restore Custom Default Configuration
If you aren't sure what programming options are in your reader, or you've changed some
options and want to restore the Factory Configuration, you have two options. You can
scan the Restore USA Factory Configuration bar code or the Restore EU Factory Configuration bar code below. Both labels restore the reader configuration to the factory settings including the interface type. The USA label restores Label IDs to those historically
used in the USA. The EU label restores Label IDs to those historically used in Europe.
The Label ID sets for USA and EU are shown in the Label ID section of this manual.
Restore USA Factory Configuration
Restore EU Factory Configuration
The programming section lists the factory default settings for each of the menu commands (indicated by shaded blocks and bold text) on the following pages.
10
QuickScanTM Lite QW2100
Chapter 3
Interfaces
Interface Selection
Each reader model will support one of the following sets of host interfaces:
USB Models (all are 2.0 full speed)
USB KBD
USB COM STD
USB OEM
RS-232 / Keyboard Wedge Models
RS-232 (Standard, Wincor-Nixdorf, OPOS)
Keyboard Wedge
Configuring the Interface
Scan the programming bar code from this section which selects the appropriate interface type
matching the system the reader will be connected to. Next, proceed to the corresponding chapter in this manual (also listed in Table 1) to configure any desired settings and features associated with that interface.
Unlike some other programming features and options, interface selections require that you scan only one programming
bar code label. DO NOT scan an ENTER/EXIT bar code prior to
scanning an interface selection bar code.
NOTE
Product Reference Guide
Some interfaces require the reader to start in the disabled state
when powered up. If additional reader configuration is desired
while in this state, pull the trigger and hold it for five seconds.
The reader will change to a state that allows programming with
bar codes.
11
Interfaces
Table 1. Available Interfaces
RS-232
FEATURES
$P,HA05,P
RS-232 standard interface
Select RS232-STD
$P,HA12,P
RS-232 Wincor-Nixdorf
Set RS-232
Interface
Features
Select RS232-WN
$P,HA13,P
starting on
page 37
RS-232 for use with OPOS/UPOS/JavaPOS
Select RS-232 OPOS
$P,HA13,P
USB Com to simulate RS-232 standard interface
Select USB-COM-STDa
USB-OEM
FEATURES
$P,HA45,P
USB-OEM
(can be used for OPOS/UPOS/JavaPOS)
Select USB-OEM
a.
12
Set USBOEM
Interface
Features
starting on
page 65
Download the correct USB Com driver from www.datalogic.com
QuickScanTM Lite QW2100
Configuring the Interface
KEYBOARD
FEATURES
$P,HA29,P
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90
& 95
w/Standard Key Encoding
Select KBD-AT
$P,HA11,P
Keyboard Wedge for IBM AT PS2 with standard
key encoding but without external keyboard
Select KBD-AT-NK
$P,HA26,P
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90
& 95
w/Alternate Key
Set KEYBOARD
WEDGE
Interface
Features
starting on
page 53
Select KBD-AT-ALT
$P,HA10,P
Keyboard Wedge for IBM AT PS2 with alternate
key
encoding but without external keyboard
Select KBD-AT-ALT-NK
$P,HA28,P
PC/XT w/Standard Key Encoding
Select KBD-XT
Product Reference Guide
13
Interfaces
KEYBOARD — cont.
FEATURES
$P,HA35,P
USB Keyboard with standard key encoding
Set KEYBOARD
WEDGE
Interface
Features
Select USB Keyboard
$P,HA2B,P
starting on
page 53
USB Keyboard with alternate key encoding
Select USB Alternate Keyboard
14
QuickScanTM Lite QW2100
Global Interface Features
ENTER/EXIT PROGRAMMING MODE
Global Interface Features
The following interface features are configurable by all interface types. To set features specific to
your interface, turn to that section of this manual:
•
RS-232 ONLY Interface on page 37
•
RS-232/USB-Com Interfaces on page 43
•
Keyboard Interface on page 53
•
USB-OEM Interface on page 65
Host Commands — Obey/Ignore
This option specifies whether the reader will obey or ignore host commands. When set to
ignore, the reader will ignore all host commands except for those necessary for:
•
service mode
•
flash programming mode
•
keeping the interface active
•
transmission of labels.
$CIFIH00
DEFAULT
Host Commands = Obey
$CIFIH01
Host Commands = Ignore
Product Reference Guide
15
Interfaces
ENTER/EXIT PROGRAMMING MODE
USB Suspend Mode
This setting enables/disables the ability of USB interfaces to enter suspend mode.
$CUSSE00
DEFAULT
USB Suspend Mode = Disable
$CUSSE01
USB Suspend Mode = Enable
16
QuickScanTM Lite QW2100
Chapter 4
General Features
Double Read Timeout
To prevent a double read of the same label, the Double Read Timeout sets the minimum time
allowed between reads of labels of the same symbology and data. If the unit reads a label and sees
the same label again within the Double Read Timeout, the second read of the label will be
ignored. Double Read Timeout does not apply to scan modes that require a trigger pull for each
label that is read.
ENTER/EXIT PROGRAMMING MODE
$CSNDR0A
Double Read Timeout = 0.1 Second
$CSNDR14
Double Read Timeout = 0.2 Second
$CSNDR1E
Double Read Timeout = 0.3 Second
$CSNDR28
DEFAULT
Double Read Timeout = 0.4 Second
Product Reference Guide
17
General Features
ENTER/EXIT PROGRAMMING MODE
Double Read Timeout — continued
$CSNDR32
Double Read Timeout = 0.5 Second
$CSNDR3C
Double Read Timeout = 0.6 Second
$CSNDR46
Double Read Timeout = 0.7 Second
$CSNDR50
Double Read Timeout = 0.8 Second
$CSNDR5A
Double Read Timeout = 0.9 Second
$CSNDR64
Double Read Timeout = 1 Second
18
QuickScanTM Lite QW2100
Label Gone Timeout
ENTER/EXIT PROGRAMMING MODE
Label Gone Timeout
This feature sets the time after the last label segment is seen before the reader prepares for a new
label. The timeout can be set within a range of 10 milliseconds to 2,550 milliseconds (2.55 seconds) in 10ms increments. Label Gone Timeout does not apply to scan modes that require a
trigger pull for each label that is read. See Label Gone Timeout on page 244 for more
detailed programming instructions.
$CSNLG
Select Label Gone Timeout Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
016 = Timeout of 160 ms
19
General Features
ENTER/EXIT PROGRAMMING MODE
Power Save Mode
When this feature is enabled, the reader will enter Power Save Mode (a lower power
consumption state) after being idle (no scanner activity) for one second.
RS-232 and USB interfaces ONLY.
NOTE
A reader having a Scan Mode setting of Object Sense, Stand
Mode, Flashing, or Always On will not enter Power Save Mode.
(The reader is always internally active when in these modes.)
$CSLEN00
Power Save Mode = Disabled
$CSLEN01
DEFAULT
Power Save Mode = Enabled
20
QuickScanTM Lite QW2100
Sleep Mode Timeout
ENTER/EXIT PROGRAMMING MODE
Sleep Mode Timeout
Specifies the timeout value for the reader to enter Sleep Mode (a very low power consumption
state).
RS-232 interface ONLY.
NOTE
A reader having a Scan Mode setting of Object Sense, Stand
Mode, Flashing, or Always On will not enter Sleep Mode. (The
reader is always internally active when in these modes.)
$CSLTO00
DEFAULT
Sleep Mode Timeout = Disabled
$CSLTO1E
Sleep Mode Timeout = 30 Seconds
$CSLTO3C
Sleep Mode Timeout = 1 Minute (60 Seconds)
$CSLTO5A
Sleep Mode Timeout = 1 Minute 30 Seconds (90 Seconds)
$CSLTO78
Sleep Mode Timeout = 2 Minutes (120 Seconds)
Product Reference Guide
21
General Features
ENTER/EXIT PROGRAMMING MODE
LED and Beeper Indicators
Power On Alert
Disables or enables the indication (from the Beeper) that the reader is receiving power.
$CBPPU00
Power On Alert = Disable (No Audible Indication)
$CBPPU01
DEFAULT
Power On Alert = Power-up Beep
22
QuickScanTM Lite QW2100
LED and Beeper Indicators
ENTER/EXIT PROGRAMMING MODE
Good Read: When to Indicate
This feature specifies when the reader will provide indication (beep and/or flash its green LED)
upon successfully reading a bar code. Choices are:
•
Good Read = Indicate after decode
•
Good Read = Indicate after transmit
•
Good Read = Indicate after CTS goes inactive, then active
This option, which uses CTS, is only valid for RS232 interfaces.
NOTE
$CBPIN00
DEFAULT
Indicate Good Read = After Decode
$CBPIN01
Indicate Good Read = After Transmit
$CBPIN02
Indicate Good Read = After CTS Goes Inactive, Then
Active
Product Reference Guide
23
General Features
ENTER/EXIT PROGRAMMING MODE
Good Read Beep Type
Specifies whether the good read beep has a mono or bitonal beep sound.
$CBPTY00
DEFAULT
Good Read Beep Type = Mono
$CBPTY01
Good Read Beep Type = Bitonal
24
QuickScanTM Lite QW2100
LED and Beeper Indicators
ENTER/EXIT PROGRAMMING MODE
Good Read Beep Frequency
Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable
from the list below. (Controls the beeper’s pitch/tone.)
$CBPFR00
Good Read Beep Frequency = Low
$CBPFR01
Good Read Beep Frequency = Medium
$CBPFR02
DEFAULT
Good Read Beep Frequency = High
Good Read Beep Length
Specifies the duration of a good read beep.
$CBPLE06
Good Read Beep Length = 60 msec
Product Reference Guide
25
General Features
ENTER/EXIT PROGRAMMING MODE
Good Read Beep Length — continued
$CBPLE08
DEFAULT
Good Read Beep Length = 80 msec
$CBPLE0A
Good Read Beep Length = 100 msec
$CBPLE0C
Good Read Beep Length = 120 msec
$CBPLE0E
Good Read Beep Length = 140 msec
$CBPLE10
Good Read Beep Length = 160 msec
$CBPLE12
Good Read Beep Length = 180 msec
$CBPLE14
Good Read Beep Length = 200 msec
26
QuickScanTM Lite QW2100
LED and Beeper Indicators
ENTER/EXIT PROGRAMMING MODE
Illumination Control
Controls illumination during a good read beep.
Setting this configuration item to turn off illumination during the beep reduces the peak current
drawn by the reader in some scanning modes.
NOTE
$CBPIC00
DEFAULT
$ = Illumination off during beep
Illumination Control
$CBPIC01
Illumination Control = Illumination and beep are
independently controlled
Product Reference Guide
27
General Features
ENTER/EXIT PROGRAMMING MODE
Good Read Beep Volume
Selects the beeper volume (loudness) upon a good read beep. There are three selectable volume
levels.
$CBPVO00
Good Read Beep Volume = Beeper Off
$CBPVO01
Good Read Beep Volume = Low
$CBPVO02
Good Read Beep Volume = Medium
$CBPVO03
DEFAULT
Good Read Beep Volume = High
28
QuickScanTM Lite QW2100
LED and Beeper Indicators
ENTER/EXIT PROGRAMMING MODE
Good Read LED Duration
This feature specifies the amount of time that the Good Read LED remains on following a good
read. The good read LED on time can be set within a range of 0.1 to 25.5 seconds in 100ms
increments. See Good Read LED Duration on page 245 for more detailed programming
instructions.
$CLAGL
Select Good Read LED Duration Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
020 = Good Read LED stays on for 2
seconds.
Indicators are dimmed during sleep.
NOTE
Product Reference Guide
29
General Features
ENTER/EXIT PROGRAMMING MODE
Scanning Features
Scan Mode
See Scan Mode on page 246 for more detailed programming instructions.
$CSNRM00
DEFAULT
Scan Mode = Trigger Single
$CSNRM01
Scan Mode = Trigger Hold Multiple
$CSNRM02
Scan Mode = Trigger Pulse Multiple
$CSNRM03
Scan Mode = Flashing
$CSNRM04
Scan Mode = Always On
$CSNRM05
Scan Mode = Autosense® Stand Mode
$CSNRM06
Scan Mode = Trigger Object Sense
30
QuickScanTM Lite QW2100
Scanning Features
ENTER/EXIT PROGRAMMING MODE
Stand Mode Triggered Timeout
This feature specifies the time to remain in Trigger Single mode after the trigger is pulled
while in Autosense® Stand Mode.
This timeout is only used when the Scan Mode is configured as Auto-
sense® Stand Mode.
NOTE
$CSNOT01
DEFAULT
Stand Mode Triggered Timeout = 0.5 Seconds
$CSNOT03
Stand Mode Triggered Timeout = 1.5 Seconds
$CSNOT04
Stand Mode Triggered Timeout = 2 Seconds
$CSNOT06
Stand Mode Triggered Timeout = 3 Seconds
$CSNOT08
Stand Mode Triggered Timeout = 4 Seconds
Product Reference Guide
31
General Features
ENTER/EXIT PROGRAMMING MODE
Stand Mode Triggered Timeout — continued
$CSNOT0C
Stand Mode Triggered Timeout = 6 Seconds
$CSNOT10
Stand Mode Triggered Timeout = 8 Seconds
$CSNOT00
Stand Mode Triggered Timeout = Switch back to Trigger
Single on trigger pull
32
QuickScanTM Lite QW2100
Scanning Features
ENTER/EXIT PROGRAMMING MODE
Scanning Active Time
This setting specifies the amount of time that the reader stays in scan ON state once the state is
entered. The range for this setting is from 1 to 255 seconds in 1-second increments. See Scanning Active Time on page 247 for more detailed programming instructions.
$CSNET
Select Scanning Active Time Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
005 = Scanning is active for 5 Seconds
Stand Mode Flash
Enables/disables the LED flash when the reader is in Stand Mode.
$CSMFL00
DEFAULT
Stand Mode Flash = Disable
$CSMFL01
Stand Mode Flash = Enable
Product Reference Guide
33
General Features
ENTER/EXIT PROGRAMMING MODE
Flash On Time
This feature specifies the ON time for the indicator LED while in Flash Mode. The selectable
range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. See
Flash On Time on page 248 for more detailed programming instructions.
$CSNFN
Select Flash ON Time Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
10 = Flash is ON for 1 Second
Flash Off Time
This feature specifies the OFF time for the indicator LED while in Flash Mode. The selectable
range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. See
Flash Off Time on page 249 for more detailed programming instructions.
$CSNFF
Select Flash OFF Time Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
34
QuickScanTM Lite QW2100
Scanning Features
ENTER/EXIT PROGRAMMING MODE
DEFAULT
06 = Flash is OFF for 600ms
Stand Mode Sensitivity
Sets the sensitivity level for stand mode wakeup. Choices are low, medium and high.
$CSMSE00
Stand Mode Sensitivity = Low
$CSMSE01
DEFAULT
Stand Mode Sensitivity = Medium
$CSMSE02
Stand Mode Sensitivity = High
Product Reference Guide
35
General Features
ENTER/EXIT PROGRAMMING MODE
Green Spot Duration
Specifies the duration of the good read pointer beam after a good read.
$CLSSP00
Green Spot Duration = Disable (Green Spot is Off)
$CLSSP01
DEFAULT
Green Spot Duration = Short (300 msec)
$CLSSP02
Green Spot Duration = Medium (500 msec)
$CLSSP03
Green Spot Duration = Long (800 msec)
36
QuickScanTM Lite QW2100
Chapter 5
RS-232 ONLY Interface
Introduction
Use the programming bar codes in this chapter if modifications to the standard RS-232 interface settings are necessary to meet your system’s requirements. Additional settings which apply
to both the RS-232 and USB interfaces are available in Chapter 6, RS-232/USB-Com Interfaces.
RS-232 Standard Factory Settings
Reference Appendix B, Standard Defaults for a listing of standard factory settings.
Baud Rate
Baud rate is the number of bits of data transmitted per second. Set the reader's baud rate to
match the baud rate setting of the host device. With an improper baud rate setting, data may
not reach the host correctly.
ENTER/EXIT PROGRAMMING MODE
$CR2BA00
Baud Rate = 1200
$CR2BA01
Baud Rate = 2400
$CR2BA02
Baud Rate = 4800
Product Reference Guide
37
RS-232 ONLY Interface
ENTER/EXIT PROGRAMMING MODE
Baud Rate — continued
$CR2BA03
DEFAULT
Baud Rate = 9600
$CR2BA04
Baud Rate = 19,200
$CR2BA05
Baud Rate = 38,400
$CR2BA06
Baud Rate = 57,600
$CR2BA07
Baud Rate = 115,200
38
QuickScanTM Lite QW2100
Data Bits
ENTER/EXIT PROGRAMMING MODE
Data Bits
This parameter allows the reader to interface with devices requiring a 7-bit or 8-bit ASCII protocol for sending and receiving data.
$CR2DA00
7 Data Bits
$CR2DA01
DEFAULT
8 Data Bits
Stop Bits
The stop bit(s) at the end of each transmitted character marks the end of transmission of one
character and prepares the receiving device for the next character in the serial data stream. The
number of stop bits selected (one or two) depends on the number the receiving terminal is programmed to accommodate. Set the number of stop bits to match host device requirements.
$CR2ST00
DEFAULT
1 Stop Bit
$CR2ST01
2 Stop Bits
Product Reference Guide
39
RS-232 ONLY Interface
ENTER/EXIT PROGRAMMING MODE
Parity
This feature specifies parity required for sending and receiving data. A parity check bit is the
most significant bit of each ASCII coded character. Select the parity type according to host
device requirements.
•
Select None when no parity bit is required.
•
Select Odd parity and the parity bit value is set to 0 or 1, based on data, to ensure that an
odd number of 1 bits are contained in the coded character.
•
Select Even parity and the parity bit value is set to 0 or 1, based on data, to ensure that an
even number of 1 bits are contained in the coded character.
$CR2PA00
DEFAULT
Parity = None
$CR2PA01
Parity = Even
$CR2PA02
Parity = Odd
40
QuickScanTM Lite QW2100
Handshaking Control
ENTER/EXIT PROGRAMMING MODE
Handshaking Control
The data interface consists of an RS-232 port designed to operate either with or without the
hardware handshaking lines, Request to Send (RTS), and Clear to Send (CTS). Handshaking
Control includes the following options:
•
RTS — RTS is asserted during transmissions. CTS is ignored.
•
RTS/CTS — RTS is asserted during transmissions. CTS gates transmissions.
•
RTS/XON/XOFF — RTS is asserted during transmissions. CTS is ignored. XON and
XOFF gate transmissions.
•
RTS On/CTS — RTS is always asserted. CTS gates transmissions.
•
RTS/CTS Scan Control — RTS is asserted during transmissions. CTS gates transmissions and controls enable and disable state of reader.
$CR2HC00
DEFAULT
Handshaking Control = RTS
$CR2HC01
Handshaking Control = RTS/CTS
$CR2HC02
Handshaking Control = RTS/XON/XOFF
$CR2HC03
Handshaking Control = RTS On/CTS
$CR2HC04
Handshaking Control = RTS/CTS Scan Control
Product Reference Guide
41
RS-232 ONLY Interface
NOTES
42
QuickScanTM Lite QW2100
Chapter 6
RS-232/USB-Com Interfaces
Introduction
The programming bar codes in this chapter allow modifications to the standard RS-232 and
USB-Com interfaces.
Standard Factory Settings
Reference Appendix B, Standard Defaults for a listing of standard factory settings.
Product Reference Guide
43
RS-232/USB-Com Interfaces
ENTER/EXIT PROGRAMMING MODE
Intercharacter Delay
This parameter specifies the intercharacter delay between the end of one character and the
beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in
10ms increments. A setting of zero specifies no delay. See Intercharacter Delay on page 250
for more detailed programming instructions.
$CR2IC00
Intercharacter Delay = No Delay
$CR2IC
Select Intercharacter Delay Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
44
00 = No Intercharacter Delay
QuickScanTM Lite QW2100
Beep On ASCII BEL
ENTER/EXIT PROGRAMMING MODE
Beep On ASCII BEL
When this parameter is enabled, the reader issues a beep when a <BEL> character is detected on
the RS-232 serial line. <BEL> is issued to gain a user's attention to an illegal entry or other
important event.
$CR2BB00
DEFAULT
Beep On ASCII BEL = Disable
$CR2BB01
Beep On ASCII BEL = Enable
Beep On Not on File
This option enables/disables the action of the reader to sound a three beep sequence upon
receiving a Not-On-File (NOF) host command.
$CBPNF00
Beep On Not On File = Disable
$CBPNF01
DEFAULT
Beep On Not On File = Enable
Product Reference Guide
45
RS-232/USB-Com Interfaces
ENTER/EXIT PROGRAMMING MODE
ACK NAK Options
This enables/disables the ability of the reader to support the RS-232 ACK/NAK protocol.
When configured, the reader and/or host sends an “ACK” when it receives data properly, and
sends “NAK” when the data is in error.
Options are:
•
Disable
•
Enable for label transmission — The reader expects an ACK/NAK response from the host
when a label is sent.
•
Enable for host-command acknowledge — The reader will respond with ACK/NAK
when the host sends a command.
•
Enable for label transmission and host-command acknowledge
$CR2AE00
DEFAULT
ACK/NAK Protocol = Disable ACK/NAK
$CR2AE01
ACK/NAK Protocol = Enable for label transmission
$CR2AE02
ACK/NAK Protocol = Enable for host-command
acknowledge
$CR2AE03
ACK/NAK Protocol = Enable for label transmission and
host-command acknowledge
46
QuickScanTM Lite QW2100
ACK NAK Options
ENTER/EXIT PROGRAMMING MODE
ACK Character
This setting specifies an ASCII character or hex value to be used as the ACK character. ASCII
characters or any hex value from 0 to 0xFF can be selected. See ACK Character on page 251
for more detailed programming instructions.
NOTE
Setting to previously defined characters such as XON,
XOFF, or host commands conflicts with normal operation of these characters. 8-bit data is not recognized
when the option Data Bits has been set as 7 Data Bits.
$CR2AC
Select ACK Character Setting
DEFAULT
0x06 ‘ACK’ Character
NAK Character
This setting specifies an ASCII character or hex value to be used as the NAK character. ASCII
characters or any hex value from 0 to 0xFF can be selected. See NAK Character on page 252
for more detailed programming instructions.
NOTE
Setting to previously defined characters such as XON,
XOFF, or host commands conflicts with normal operation of these characters. 8-bit data is not recognized
when the option Data Bits has been set as 7 Data Bits.
$CR2NA
Select NAK Character Setting
DEFAULT
Product Reference Guide
0x15 ‘NAK’ Character
47
RS-232/USB-Com Interfaces
ENTER/EXIT PROGRAMMING MODE
ACK NAK Timeout Value
This option specifies the amount of time the reader waits for an ACK character from the host
following label transmission. The selectable timeout range is 200 milliseconds to 15,000ms (15
seconds) in 200ms increments. A selection of 0 disables the timeout. See ACK NAK Timeout
Value on page 253 for more detailed programming instructions.
$CR2AT
Select ACK NAK Timeout Value Setting
~
Make a mistake? Scan the CANCEL bar code to
abort and not save the entry string. You can then
start again at the beginning.
CANCEL
DEFAULT
48
01 ACK NAK Timeout value is 200ms
QuickScanTM Lite QW2100
ACK NAK Options
ENTER/EXIT PROGRAMMING MODE
ACK NAK Retry Count
This feature specifies the number of times the reader retries a label transmission due to a retry
condition. The selectable range is from 1 to 254 retries. A selection of 0 disables the count, and
a selection of 255 specifies unlimited retries. See ACK NAK Retry Count on page 254 for
more detailed programming instructions.
$CR2AR
Select ACK NAK Retry Count Setting
~
Make a mistake? Scan the CANCEL bar code to
abort and not save the entry string. You can then
start again at the beginning.
CANCEL
DEFAULT
Product Reference Guide
003 = 3 Retries
49
RS-232/USB-Com Interfaces
ENTER/EXIT PROGRAMMING MODE
ACK NAK Error Handling
This feature specifies the method the reader uses to handle receive errors detected while waiting
for an ACK character from the host.
Options are:
• Ignore errors detected
• Process error as valid ACK character
• Process error as valid NAK character
$CR2EH00
DEFAULT
ACK NAK Error Handling = Ignore Errors Detected
$CR2EH01
ACK NAK Error Handling = Process Error as Valid ACK
Character
$CR2EH02
ACK NAK Error Handling = Process Error as
Valid NAK Character
50
QuickScanTM Lite QW2100
Indicate Transmission Failure
ENTER/EXIT PROGRAMMING MODE
Indicate Transmission Failure
This option enables/disables the reader’s ability to sound an error beep to indicate a transmission
failure while in ACK/NAK mode.
$CR2TF00
Indicate Transmission Failure = Disable Indication
$CR2TF01
DEFAULT
Indicate Transmission Failure = Enable Indication
Disable Character
Specifies the value of the RS-232 host command used to disable the reader.
ASCII characters or any hex value from 0 to 0xFF can be selected. See Disable Character on
page 255 for more detailed programming instructions.
NOTE
Setting to previously defined characters such as XON,
XOFF, or host commands conflicts with normal operation of these characters. 8-bit data is not recognized
when the option Data Bits has been set as 7 Data Bits.
$CR2DC
Select Disable Character Setting
DEFAULT
Product Reference Guide
0x44 = Disable Character is ‘D’
51
RS-232/USB-Com Interfaces
ENTER/EXIT PROGRAMMING MODE
Enable Character
Specifies the value of the RS-232 host command used to enable the reader.
ASCII characters or any hex value from 0 to 0xFF can be selected. See Enable Character on
page 256 for more detailed programming instructions.
NOTE
Setting to previously defined characters such as XON,
XOFF, or host commands conflicts with normal operation of these characters. 8-bit data is not recognized
when the option Data Bits has been set as 7 Data Bits.
$CR2EC
Select Enable Character Setting
DEFAULT
52
0x45 = Enable Character is ‘E’
QuickScanTM Lite QW2100
Chapter 7
Keyboard Interface
Introduction
Use the programming bar codes in this chapter to select options for USB Keyboard and Wedge
Interfaces.
Standard Factory Settings
Reference Appendix B, Standard Defaults for a listing of standard factory settings.
Scancode Tables
Information about control character emulation which applies to keyboard interfaces is listed in
Appendix F, Scancode Tables.
Product Reference Guide
53
Keyboard Interface
ENTER/EXIT PROGRAMMING MODE
Country Mode
This feature specifies the country/language supported by the keyboard.
Country Modes are only valid for the following interfaces:
•
USB Keyboard (without alternate key encoding)
•
Keyboard Wedge
Below are the Country Modes supported by each product version (Standard or European):
Supported Country
Codes
English (USA)
Spanish (Latin American)
Japanese
Polish
Portuguese (Brazilian)
Russian
Hungarian
Croation
Romanian
Czech
Slovakian
Italian
French
German
English (British)
Swedish
Belgian
Danish
Norwegian
Swiss
Standard
Version
European
Version
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
$CKBCO00
DEFAULT
Country Mode = English (USA)
$CKBCO01
Country Mode = Belgian
54
QuickScanTM Lite QW2100
Country Mode
ENTER/EXIT PROGRAMMING MODE
Country Mode — continued
$CKBCO02
Country Mode = English (British)
$CKBCO11
Country Mode = Croatian
$CKBCO0E
Country Mode = Czech
$CKBCO03
Country Mode = Danish
$CKBCO04
Country Mode = French
$CKBCO05
Country Mode = German
$CKBCO0D
Country Mode = Hungarian
Product Reference Guide
55
Keyboard Interface
ENTER/EXIT PROGRAMMING MODE
Country Mode — continued
$CKBCO06
Country Mode = Italian
$CKBCO0C
Country Mode = Japanese 106-key
$CKBCO07
Country Mode = Norwegian
$CKBCO12
Country Mode = Polish
$CKBCO08
Country Mode = Portuguese (Brazilian)
$CKBCO10
Country Mode = Romanian
$CKBCO0F
Country Mode = Slovakian
56
QuickScanTM Lite QW2100
Caps Lock State
ENTER/EXIT PROGRAMMING MODE
Country Mode — continued
$CKBCO09
Country Mode = Spanish (Latin American)
$CKBCO0A
Country Mode = Swedish
$CKBCO0B
Country Mode = Swiss
Caps Lock State
This option specifies the format in which the reader sends character data. This applies to Keyboard Wedge interfaces. This does not apply when an alternate key encoding keyboard is selected.
$CKBCL00
DEFAULT
Caps Lock State = Caps Lock OFF
$CKBCL01
Caps Lock State = Caps Lock ON
$CKBCL02
Caps Lock State = AUTO Caps Lock Enable
Product Reference Guide
57
Keyboard Interface
ENTER/EXIT PROGRAMMING MODE
Numlock
This option specifies the setting of the Numbers Lock (Numlock) key while in Keyboard Wedge
interface. This only applies to alternate key encoding interfaces. It does not apply to USB Keyboard.
$CKBNL00
DEFAULT
Numlock = Numlock key unchanged
$CKBNL01
Numlock = Numlock key toggled
Keyboard Numeric Keypad
This feature specifies if numeric characters will be sent using the standard keys or the numeric
keypad.
$CKBKP00
DEFAULT
Keyboard Numeric Keypad = Standard Keys
$CKBKP01
Keyboard Numeric Keypad = Numeric Keypad
58
QuickScanTM Lite QW2100
Keyboard Send Control Characters
ENTER/EXIT PROGRAMMING MODE
Keyboard Send Control Characters
This feature is used by the Keyboard Wedge and USB Keyboard interfaces. It specifies how the
reader transmits ASCII control characters to the host. Reference Appendix F, Scancode
Tables for more information about control characters.
Options are as follows:
Send Ctrl+Key — ASCII characters from 00H to 0x1FH inclusive are transmitted in the format Ctrl+Key. Special keys are available in the range from 81H to A1.
Send Ctrl+Shift+Key — The behavior is the same as above, but control keys are sent in the
format Ctrl+Shift+Keys.
Send Special Function Key — Send characters between 00H and 1FH according to the special function key mapping table (see Microsoft Windows Codepage 1252 on page 310).
This is used to send keys that are not in the normal ASCII set. A unique set is provided for each
available scancode set.
$CKBSC00
DEFAULT
Keyboard Send Control Characters = 00
$CKBSC01
Keyboard Send Control Characters = 01
$CKBSC02
Keyboard Send Control Characters = 02
Product Reference Guide
59
Keyboard Interface
ENTER/EXIT PROGRAMMING MODE
Wedge Quiet Interval
This option specifies the amount of time to look for keyboard activity before the reader breaks
the keyboard connection in order to transmit data to host. The selectable range for this feature is
from 0 to 990ms in 10ms increments. See Wedge Quiet Interval on page 257 for more
detailed programming instructions.
This feature applies ONLY to the Keyboard Wedge interface.
NOTE
$CKBQI
Select Wedge Quiet Interval Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
60
10 = Quiet Interval of 100 ms
QuickScanTM Lite QW2100
Intercharacter Delay
ENTER/EXIT PROGRAMMING MODE
Intercharacter Delay
This parameter specifies the intercharacter delay between the end of one character and the
beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in
10ms increments. A setting of zero specifies no delay. See Intercharacter Delay on
page 258 for more detailed programming instructions.
This feature applies ONLY to the Keyboard Wedge interface.
NOTE
$CR21C00
Intercharacter Delay = No Delay
$CR21C
Select Intercharacter Delay Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
00 = No Intercharacter Delay
61
Keyboard Interface
ENTER/EXIT PROGRAMMING MODE
Intercode Delay
Specifies the delay between labels transmitted to the host for this interface. The selectable range
for this feature is from 0 to 99 seconds. See Intercode Delay on page 259 for more detailed
programming instructions.
$CKBID
Set Intercode Delay
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
62
00 = No Wedge Intercode Delay
QuickScanTM Lite QW2100
USB Keyboard Speed
ENTER/EXIT PROGRAMMING MODE
USB Keyboard Speed
This option specifies the USB poll rate for a USB Keyboard.
This feature applies ONLY to the USB Keyboard interface.
NOTE
$CKBSP01
DEFAULT
USB Keyboard Speed = 1ms
$CKBSP02
USB Keyboard Speed = 2ms
$CKBSP03
USB Keyboard Speed = 3ms
$CKBSP04
USB Keyboard Speed = 4ms
$CKBSP05
USB Keyboard Speed = 5ms
Product Reference Guide
63
Keyboard Interface
ENTER/EXIT PROGRAMMING MODE
USB Keyboard Speed — continued
$CKBSP06
USB Keyboard Speed = 6ms
$CKBSP07
USB Keyboard Speed = 7ms
$CKBSP08
USB Keyboard Speed = 8ms
$CKBSP09
USB Keyboard Speed = 9ms
$CKBSP0A
USB Keyboard Speed = 10ms
64
QuickScanTM Lite QW2100
Chapter 8
USB-OEM Interface
Introduction
Feature settings for USB interfaces differ depending upon which host type the reader will be
connected with. Use the feature settings in this chapter to specifically configure for the USBOEM interface. Other USB interfaces are included in the approprite chapter for their host type.
Standard Factory Settings
Reference Appendix B, Standard Defaults for a listing of standard factory settings.
Product Reference Guide
65
USB-OEM Interface
ENTER/EXIT PROGRAMMING MODE
USB-OEM Device Usage
The USB-OEM protocol allows for the reader to be identified as one of two different types of
bar code readers. Depending on what other scanners you may already have connected to a USBOEM POS, you may need to change this setting to enable all devices to communicate.
Options are:
• Table Top Scanner
• Handheld Scanner
It may be necessary to switch device usage when connecting
two readers/scanners of the same type to a POS system.
NOTE
$CIBUT00
USB-OEM Device Usage = Table Top Scanner
$CIBUT01
DEFAULT
USB-OEM Device Usage = Handheld Scanner
USB-OEM Interface Options
This setting provides for an interface specific control mechanism..
Options are:
• Obey — Obey Reader Configuration Host Commands
• Ignore — Ignore Reader Configuration Host Commands
$CIFO101
USB-OEM Interface Options = Obey
$CIFO102
DEFAULT
USB-OEM Interface Options = Ignore
66
QuickScanTM Lite QW2100
Chapter 9
Data Editing
Data Editing Overview
When a bar code is scanned, additional information can be sent to the host computer along
with the bar code data. This combination of bar code data and supplementary user-defined data
is called a “message string.” The features in this chapter can be used to build specific userdefined data into a message string.
There are several types of selectable data characters that can be sent before and after scanned
data. You can specify if they should be sent with all symbologies, or only with specific symbologies. Figure 6 shows the available elements you can add to a message string:
Figure 6. Breakdown of a Message String
Label ID Transmission:
Enable this option to
transmit the Label ID you
configure for the scanned
symbology.
Prefix
Label ID
AIM ID
OR...
Bar Code Data
Label ID
Suffix
AIM ID: This function is used to identify and display the
common label identifier for its symbology. When enabled,
this ID code will be transmitted before the scanned bar
code data.
00 - 20 Characters (ASCII)
Additional advanced editing is available. See the Advanced Formatting features in the Datalogic Aladdin Configuration Application or
contact Technical Support on page 3 for more information.
NOTE
Product Reference Guide
67
Data Editing
ENTER/EXIT PROGRAMMING MODE
Please Keep In Mind...
•
Modifying a message string is not a mandatory requirement. Data editing is sophisticated
feature allowing highly customizable output for advanced users. Factory default settings
for data editing is typically set to NONE.
•
A prefix or suffix may be applied (reference the Symbologies chapter for these settings)
across all symbologies (set via the Global features in this chapter).
•
You can add any character from the ASCII Chart (from 00-FF) on the inside back cover
of this manual as a prefix, suffix or Label ID.
•
Enter prefixes and suffixes in the order in which you want them to appear on the output.
Global Prefix/Suffix
Up to 20 ASCII characters may be added as a prefix (in a position before the bar code data) and/
or as a suffix (in a position following the bar code data) as indicated in . See Global Prefix/Suffix on page 260 for more detailed programming instructions.
$CLFPR
Set Global Prefix
$CLFSU
Set Global Suffix
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
68
No Global Prefix
Global Suffix = 0x0D
QuickScanTM Lite QW2100
Global AIM ID
ENTER/EXIT PROGRAMMING MODE
Global AIM ID
This feature enables/disables addition of AIM IDs for all symbology types.
NOTE
AIM label identifiers (as opposed to custom characters you select yourself as with label identifiers) can be included with scanned bar code data. See Global AIM ID on page 261 for more
detailed programming instructions.
$CAIEN00
DEFAULT
Global AIM ID = Disable
$CAIEN01
Global AIM ID = Enable
GS1-128 AIM ID
If Global AIM ID is disabled, the AIM ID for GS1-128 can be enabled/disabled independently.
The AIM ID for GS1-128 is a ]C1, ]C2 or ]C3.
AIM IDs for other symbologies can be enabled/disabled independently as well. Contact Customer Support for assistance.
$CU8AI00
GS1-128 AIM ID = Disable
$CU8AI01
DEFAULT
GS1-128 AIM ID = Enable
Product Reference Guide
69
Data Editing
ENTER/EXIT PROGRAMMING MODE
Label ID
A Label ID is a customizable code of up to three ASCII characters (each can be one of hex
0x01-0xFF), used to identify a bar code (symbology) type. It can be appended previous to or following the transmitted bar code data depending upon how this option is enabled. This feature
provides options for configuring custom Label IDs as a pre-loaded set (see Label ID: Preloaded Sets on page 70) or individually per symbology (see Label ID: Set Individually
Per Symbology on page 71). If you wish to program the reader to always include an industry standard label identifier for ALL symbology types, see the previous feature Global AIM ID
on page 69.
Label ID: Pre-loaded Sets
The reader supports two pre-loaded sets of Label IDs. shows the USA set and the EU set. See
Label ID: Pre-loaded Sets on page 262 for more information concerning the pre-loaded
sets that are provided.
CAUTION
When changing from one Label ID set to another, all other reader configuration settings, including the host interface type, will be erased
and set to the factory defaults. Any custom configuration or custom
defaults will be lost.
$AE
DEFAULT
Label ID Pre-loaded Set = USA Set
$Ae
Label ID Pre-loaded Set = EU Set
70
QuickScanTM Lite QW2100
Label ID
ENTER/EXIT PROGRAMMING MODE
Label ID: Set Individually Per Symbology
This feature configures a Label ID individually for a single symbology.
This setting requires the scanning of bar codes from multiple
sections. See Label ID: Set Individually Per Symbology
on page 264 for more detailed programming instructions.
NOTE
Label ID Control
This option controls whether a Label ID is disabled, or sent as a prefix or suffix for a given symbology type.
$CIDCO00
DEFAULT
Label ID Transmission = Disable
$CIDCO01
Label ID Transmission = Enable as Prefix
$CIDCO02
Label ID Transmission = Enable as Suffix
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
Product Reference Guide
71
Data Editing
ENTER/EXIT PROGRAMMING MODE
Label ID — continued
Label ID Symbology Selection
This option selects the symbology for which a Label ID is to be configured. See Label ID: Set
Individually Per Symbology on page 264 for full instructions.
$CABID
Set UPC-A Label ID Character(s)
$CA2ID
Set UPC-A/P2 Label ID Character(s)
$CA5ID
Set UPC-A/P5 Label ID Character(s)
$CA8ID
Set UPC-A/GS1-128 Label ID Character(s)
$CEBID
Set UPC-E Label ID Character(s)
$CE2ID
Set UPC-E/P2 Label ID Character(s)
72
QuickScanTM Lite QW2100
Label ID
ENTER/EXIT PROGRAMMING MODE
Label ID — continued
Label ID Symbology Selection — continued
This option selects the symbology for which a Label ID is to be configured. See Label ID: Set
Individually Per Symbology on page 264 for full instructions.
$CE5ID
Set UPC-E/P5 Label ID Character(s)
$CE8ID
Set UPC-E/GS1-128 Label ID Character(s)
$C3BID
Set EAN 13 Label ID Character(s)
$C32ID
Set EAN 13/P2 Label ID Character(s)
$C35ID
Set EAN 13/P5 Label ID Character(s)
$C38ID
Set EAN 13/GS1-128 Label ID Character(s)
Product Reference Guide
73
Data Editing
ENTER/EXIT PROGRAMMING MODE
Label ID — continued
Label ID Symbology Selection — continued
This option selects the symbology for which a Label ID is to be configured. See Label ID: Set
Individually Per Symbology on page 264 for full instructions.
$C8BID
Set EAN 8 Label ID Character(s)
$C82ID
Set EAN 8/P2 Label ID Character(s)
$C85ID
Set EAN 8/P5 Label ID Character(s)
$C88ID
Set EAN 8/GS1-128 Label ID Character(s)
$C4BID
Set GS1 DataBar Omnidirectional Label ID Character(s)
$CXBID
Set GS1 DataBar Expanded Label ID Character(s)
74
QuickScanTM Lite QW2100
Label ID
ENTER/EXIT PROGRAMMING MODE
Label ID — continued
Label ID Symbology Selection — continued
This option selects the symbology for which a Label ID is to be configured. See Label ID: Set
Individually Per Symbology on page 264 for full instructions.
$CLBID
Set GS1 DataBar Limited Label ID Character(s)
$CC3ID
Set Code 39 Label ID Character(s)
$CP3ID
Set Code 32 Label ID Character(s)
$CCCID
Set Code 39 CIP Label ID Character(s)
$CC8ID
Set Code 128 Label ID Character(s)
$CU8ID
Set GS1-128 Label ID Character(s)
Product Reference Guide
75
Data Editing
ENTER/EXIT PROGRAMMING MODE
Label ID — continued
Label ID Symbology Selection — continued
This option selects the symbology for which a Label ID is to be configured. See Label ID: Set
Individually Per Symbology on page 264 for full instructions.
$CI2ID
Set Interleaved 2 of 5 Label ID Character(s)
$CHRID
Set Interleaved 2 of 5 CIP HR Label ID Character(s)
$CD2ID
Set Datalogic 2 of 5 CIP HR Label ID Character(s)
$CCBID
Set Codabar Label ID Character(s)
$CACID
Set ABC Codabar Label ID Character(s)
$CC1ID
Set Code 11 Label ID Character(s)
76
QuickScanTM Lite QW2100
Label ID
ENTER/EXIT PROGRAMMING MODE
Label ID — continued
Label ID Symbology Selection — continued
This option selects the symbology for which a Label ID is to be configured. See Label ID: Set
Individually Per Symbology on page 264 for full instructions.
$CS2ID
Set Standard 2 of 5 Label ID Character(s)
$CU2ID
Set Industrial 2 of 5 Label ID Character(s)
$CINID
Set ISSN Label ID Character(s)
$CIAID
Set IATA Label ID Character(s)
$CI8ID
Set Concatinated ISBT 128 Label ID Character(s)
$CMSID
Set MSI Label ID Character(s)
Product Reference Guide
77
Data Editing
ENTER/EXIT PROGRAMMING MODE
Label ID — continued
Label ID Symbology Selection — continued
This option selects the symbology for which a Label ID is to be configured. See Label ID: Set
Individually Per Symbology on page 264 for full instructions.
$CC9ID
Set Code 93 Label ID Character(s)
$CCFID
Set Codablock F Label ID Character(s)
$CCRID
Set Code 4 Label ID Character(s)
$CCC5ID
$
Set Code 5 Label ID Character(s)
$CF2ID
$
Set Follett 2 of 5 Label ID Character(s)
78
QuickScanTM Lite QW2100
Label ID
ENTER/EXIT PROGRAMMING MODE
Label ID — continued
Label ID Symbology Selection — continued
This option selects the symbology for which a Label ID is to be configured. See Label ID: Set
Individually Per Symbology on page 264 for full instructions.
$CISID
Set ISBN Label ID Character(s)
$CI8ID
Set Concatenated ISBT Label ID Character(s)
Product Reference Guide
79
Data Editing
ENTER/EXIT PROGRAMMING MODE
Set Global Mid Label ID Character(s)
Specifies a mid-label ID that is added for transmission between the labels of a two label pair.
The expected string is a maximum of 20 characters. When combining two label pairs into a single label for transmission to the host, this label ID can be added to the data, following the first
label and preceding the second label. To set this feature...
1. Scan the ENTER/EXIT bar code.
2. Determine the desired character(s) (you may choose up to twenty) which will represent
the Mid Label ID for two label pairs. If the first character is 00, then nothing is added
between the two labels.
3. Turn to the ASCII Chart on the inside back cover of this manual and find the equivalent
hex digits associated with your choice of Label ID. For example, if you wish to select the
characters ‘M’, ‘I’ and ‘D’ as a Label ID, the chart indicates its associated hex characters as
4D4944. Turn to Keypad, starting on page 297 and scan the bar codes representing
the hex characters determined. For the example given, the characters ‘4’, ‘D’, ‘4’, ‘9’, ‘4’
and ‘4’ would be scanned. More examples of Label ID settings are provided in Table 18.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
4. The reader will save the string and exit Programming Mode when...
• the ENTER/EXIT baqr code is scanned a second time, or
• the hex values for all twenty available characters have been entered, or
• the first 00 hex value entered terminates the string.
This completes the steps to configure a Global Mid Label ID for two label pairs.
$CN2MI
Set Global Mid Label ID Character(s)
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
80
No Global Mid Label ID
Character(s)
00000000000000000000
QuickScanTM Lite QW2100
Case Conversion
ENTER/EXIT PROGRAMMING MODE
Case Conversion
This feature allows conversion of the case of all alphabetic characters to upper or lower case.
Case conversion affects ONLY scanned bar code data, and
does not affect Label ID, Prefix, Suffix, or other appended data.
NOTE
$CLFCA00
DEFAULT
Case Conversion = Disable (no case conversion)
$CLFCA01
Case Conversion = Convert to upper case
$CLFCA02
Case Conversion = Convert to lower case
Product Reference Guide
81
Data Editing
ENTER/EXIT PROGRAMMING MODE
Character Conversion
Character conversion is an eight byte configuration item. The eight bytes are 4 character pairs
represented in hexadecimal ASCII values. The first character in the pair is the character that will
be converted. The second character in the pair is the character to convert to. If the character to
convert in a pair is FF, then no conversion is done. See Character Conversion on page 266
for more detailed programming instructions.
$CLFCH
Configure Character Conversion
DEFAULT
82
0xFFFFFFFFFFFFFFFF
QuickScanTM Lite QW2100
Chapter 10
Symbologies
Introduction
The reader supports the following symbologies (bar code types). Options for each symbology
are included in this chapter.
Symbologies
•
UPC-A
•
Datalogic 2 of 5
•
UPC-E
•
Codabar
•
EAN 13
•
ABC Codabar
•
EAN 13 (JAN 13)
•
Code 11
•
EAN 8 (JAN 8)
•
Standard 2 of 5
•
Add-Ons
•
Industrial 2 of 5
•
GS1 DataBarTM Omnidirectional
•
IATA
•
GS1 DataBarTM Expanded
•
ISBT 128
•
GS1 DataBarTM Limited
•
MSI
•
Code 39
•
Code 93
•
Code 32 (Italian Pharmaceutical)
•
Codablock F
•
Code 39 CIP (French Pharmaceutical)
•
Code 4
•
Code 128
•
Code 5
•
GS1-128
•
Follett 2 of 5
•
Interleaved 2 of 5 (I 2 of 5)
•
BC412
•
Interleaved 2 of 5 CIP HR
Standard Factory Settings for Symbologies
Default settings are indicated at each feature/option with a green arrow. Also reference Appendix B, Standard Defaults for a listing of the most widely used set of standard factory settings.
That section also provides space to record any custom settings needed or implemented for your
system.
Product Reference Guide
83
Symbologies
ENTER/EXIT PROGRAMMING MODE
Disable All Symbologies
Scan this label to disable all symbologies.
$AD
Disable all symbologies
Coupon Control
This feature is used to control the method of processing coupon labels.
Options are:
•
Allow all — allow all coupon bar codes to be decoded
•
Enable only UPC/EAN — enables only UPC/EAN coupon decoding
•
Enable only GS1 DataBar — enables only GS1 DataBar coupon decoding
To set this feature:
1. Scan the Enter/Exit bar code.
2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes
on this and the facing page to ensure that the reader sees only the bar code you intend to
scan.
3. Complete the programming sequence by scanning the Enter/Exit bar code.
$CCPCL00
Coupon Control = Allow all
$CCPCL01
DEFAULT
Coupon Control = Enable only UPC/EAN
$CCPCL02
Coupon Control = Enable only GS1 DataBar
84
TM
QuickScan
Lite QW2100
UPC-A
ENTER/EXIT PROGRAMMING MODE
UPC-A
The following options apply to the UPC-A symbology.
UPC-A Enable/Disable
When disabled, the reader will not read UPC-A bar codes.
$CABEN00
UPC-A = Disable
$CABEN01
DEFAULT
UPC-A = Enable
UPC-A Check Character Transmission
Enable this option to transmit the check character along with UPC-A bar code data.
$CABCT00
UPC-A Check Character Transmission = Don’t Send
$CABCT01
DEFAULT
UPC-A Check Character Transmission = Send
Product Reference Guide
85
Symbologies
ENTER/EXIT PROGRAMMING MODE
UPC-A — cont.
Expand UPC-A to EAN-13
Expands UPC-A data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13.
$CAB3B00
DEFAULT
UPC-A to EAN-13 = Don’t Expand
$CAB3B01
UPC-A to EAN-13 = Expand
UPC-A Number System Character Transmission
This feature enables/disables transmission of the UPC-A number system character.
$CABNS00
UPC-A Number System Character = Do not transmit
$CABNS01
DEFAULT
UPC-A Number System Character = Transmit
86
TM
QuickScan
Lite QW2100
UPC-A
ENTER/EXIT PROGRAMMING MODE
UPC-A — cont.
In-Store Minimum Reads
This feature specifies the minimum number of consecutive times an in-store label must be
decoded before it is accepted as good read.
In-store labels are defined as UPC-A labels with a number-system character of 2 or 4 as well as
EAN 8 and EAN 13 labels with a Flag1 character of 2 or an EAN 13 label starting with the
three characters '980'.
$CINMR01
In-Store Minimum Reads = 1
$CINMR02
DEFAULT
In-Store Minimum Reads = 2
$CINMR03
In-Store Minimum Reads = 3
$CINMR04
In-Store Minimum Reads = 4
Product Reference Guide
87
Symbologies
ENTER/EXIT PROGRAMMING MODE
UPC-E
The following options apply to the UPC-E symbology.
UPC-E Enable/Disable
When disabled, the reader will not read UPC-E bar codes.
$CEBEN00
UPC-E = Disable
$CEBEN01
DEFAULT
UPC-E = Enable
UPC-E Check Character Transmission
Enable this option to transmit the check character along with UPC-E bar code data.
$CEBCT00
UPC-E Check Character Transmission = Don’t Send
$CEBCT01
DEFAULT
UPC-E Check Character Transmission = Send
88
TM
QuickScan
Lite QW2100
UPC-E
ENTER/EXIT PROGRAMMING MODE
UPC-E — cont.
Expand UPC-E to EAN-13
Expands UPC-E data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13.
$CEB3B00
DEFAULT
UPC-E to EAN-13 = Don’t Expand
$CEB3B01
UPC-E to EAN-13 = Expand
Expand UPC-E to UPC-A
Expands UPC-E data to the UPC-A data format.
$CEBAB00
DEFAULT
UPC-E to UPC-A = Don’t Expand
$CEBAB01
UPC-E to UPC-A = Expand
Product Reference Guide
89
Symbologies
ENTER/EXIT PROGRAMMING MODE
UPC-E — cont.
UPC-E Number System Character Transmission
This feature enables/disables transmission of the UPC-E system number character.
$CEBNS00
UPC-E Number System Character = Do not transmit
$CEBNS01
DEFAULT
UPC-E Number System Character = Transmit
UPC-E Minimum Reads
This feature specifies the minimum number of consecutive times a UPC-E label must be
decoded before it is accepted as good read.
$CEBMR01
UPC-E Minimum Reads = 1
$CEBMR02
DEFAULT
UPC-E Minimum Reads = 2
$CEBMR03
UPC-E Minimum Reads = 3
$CEBMR04
UPC-E Minimum Reads = 4
90
TM
QuickScan
Lite QW2100
EAN 13
ENTER/EXIT PROGRAMMING MODE
EAN 13
The following options apply to the EAN 13 (Jan 13) symbology.
EAN 13 Enable/Disable
When disabled, the reader will not read EAN 13/JAN 13 bar codes.
$C3BEN00
EAN 13 = Disable
$C3BEN01
DEFAULT
EAN 13 = Enable
EAN 13 Check Character Transmission
Enable this option to transmit the check character along with EAN 13 bar code data.
$C3BCT00
EAN 13 Check Character Transmission = Don’t Send
$C3BCT01
DEFAULT
EAN 13 Check Character Transmission = Send
Product Reference Guide
91
Symbologies
ENTER/EXIT PROGRAMMING MODE
EAN 13 — cont.
EAN-13 Flag 1 Character
Enables/disables transmission of an EAN/JAN13 Flag1 character. The Flag 1 character is the
first character of the label.
$C3BF100
EAN-13 Flag 1 Char= Don’t transmit
$C3BF101
DEFAULT
EAN-13 Flag 1 Char= Transmit
EAN-13 ISBN Conversion
This option enables/disables conversion of EAN 13/JAN 13 Bookland labels starting with 978
to ISBN labels.
$C3BIS00
DEFAULT
EAN-13 ISBN Conversion = Disable
$C3BIS01
EAN-13 ISBN Conversion = Convert to ISBN
92
TM
QuickScan
Lite QW2100
EAN 13
ENTER/EXIT PROGRAMMING MODE
EAN 13 — cont.
ISSN Enable/Disable
Enables/disables conversion of EAN/JAN13 Bookland labels starting with 977 to ISSN labels.
$C3BIN00
DEFAULT
ISSN = Disable
$C3BIN01
ISSN = Enable
EAN 13 Minimum Reads
This feature specifies the minimum number of consecutive times an EAN 13 label must be
decoded before it is accepted as good read.
$C3BMR01
DEFAULT
EAN 13 Minimum Reads = 1
$C3BMR02
EAN 13 Minimum Reads = 2
$C3BMR03
EAN 13 Minimum Reads = 3
$C3BMR04
EAN 13 Minimum Reads = 4
Product Reference Guide
93
Symbologies
ENTER/EXIT PROGRAMMING MODE
EAN 8
The following options apply to the EAN 8 (Jan 8) symbology.
EAN 8 Enable/Disable
When disabled, the reader will not read EAN 8/JAN 8 bar codes.
$C8BEN00
EAN 8 = Disable
$C8BEN01
DEFAULT
EAN 8 = Enable
EAN 8 Check Character Transmission
Enable this option to transmit the check character along with EAN 8 bar code data.
$C8BCT00
EAN 8 Check Character Transmission = Don’t Send
$C8BCT01
DEFAULT
EAN 8 Check Character Transmission = Send
94
TM
QuickScan
Lite QW2100
EAN 8
ENTER/EXIT PROGRAMMING MODE
EAN 8 — cont.
Expand EAN 8 to EAN 13
Enable this option to expand EAN 8/JAN 8 labels to EAN 13/JAN 13.
$C8B3B00
DEFAULT
Expand EAN 8 to EAN 13 = Disable
$C8B3B01
Expand EAN 8 to EAN 13 = Enable
EAN 8 Both Guards Substitution
Enables/disables the ability of the reader to find an EAN/JAN8 guard pattern in caseswhere the
EAN/JAN8 margin makes the guard look like a character.
$C8BG200
DEFAULT
EAN 8 Both Guards Substitution = Disable
$C8BG201
EAN 8 Both Guards Substitution = Enable
Product Reference Guide
95
Symbologies
ENTER/EXIT PROGRAMMING MODE
EAN 8 — cont.
EAN 8 Guard Insertion
Enables/disables the ability to insert a guard into an otherwise full-strike EAN 8 segment.
$C8BGI00
DEFAULT
EAN 8 Guard Insertion = Disable
$C8BGI01
EAN 8 Guard Insertion = Enable
EAN 8 Guard Substitution
Enables/disables the ability of the reader to substitute guard pattern for even parity 6 when an
EAN/JAN8 label is presented.
$C8BGS00
DEFAULT
EAN 8 Guard Substitution = Disable
$C8BGS01
EAN 8 Guard Substitution = Enable
96
TM
QuickScan
Lite QW2100
EAN 8
ENTER/EXIT PROGRAMMING MODE
EAN 8 — cont.
EAN 8 Minimum Segment Length Block
Specifies the minimum number of characters necessary in an EAN/JAN8 label segment in order
for the reader to accept the segment for decoding.
$C8BSB05
EAN 8 Minimum Segment Length Block = 5
$C8BSB06
EAN 8 Minimum Segment Length Block = 6
$C8BSB07
EAN 8 Minimum Segment Length Block = 7
$C8BSB08
DEFAULT
EAN 8 Minimum Segment Length Block = 8
$C8BSB09
EAN 8 Minimum Segment Length Block = 9
$C8BSB0A
EAN 8 Minimum Segment Length Block = 10
Product Reference Guide
97
Symbologies
ENTER/EXIT PROGRAMMING MODE
EAN 8 — cont.
EAN 8 Minimum Segment Length Block — cont.
$C8BSB0B
EAN 8 Minimum Segment Length Block = 11
$C8BSB0C
EAN 8 Minimum Segment Length Block = 12
$C8BSB0D
EAN 8 Minimum Segment Length Block = 13
$C8BSB0E
EAN 8 Minimum Segment Length Block = 14
$C8BSB0F
EAN 8 Minimum Segment Length Block = 15
98
TM
QuickScan
Lite QW2100
EAN 8
ENTER/EXIT PROGRAMMING MODE
EAN 8 — cont.
EAN 8 Minimum Reads
This feature specifies the minimum number of consecutive times an EAN 8 (Jan 8) label must
be decoded before it is accepted as good read.
$C8BMR01
DEFAULT
EAN 8 Minimum Reads = 1
$C8BMR02
EAN 8 Minimum Reads = 2
$C8BMR03
EAN 8 Minimum Reads = 3
$C8BMR04
EAN 8 Minimum Reads = 4
Product Reference Guide
99
Symbologies
ENTER/EXIT PROGRAMMING MODE
EAN 8 — cont.
EAN 8 Stitch Exact Label Halves
Enables/disables the abiliy to stitch exact EAN 8 label halves with no overlapping characters.
The label halves being stitched together to assemble a complete label must have the structure GddddC and CddddG.
NOTE
$C8BSE00
DEFAULT
EAN 8 Stitch Exact Label Halves = Disable
$C8BSE01
EAN 8 Stitch Exact Label Halves = Enable
EAN 8 Stitch Unlike Label Halves
Enables/disables the abiliy to stitch EAN 8 label halves together which may have differing characters in them.
The label structure must be GddddCd... and ..dCddddG. The
characters dCd must match between the two segments.
NOTE
$C8BSU00
DEFAULT
EAN 8 Stitch Unlike Label Halves = Disable
$C8BSU01
EAN 8 Stitch Unlike Label Halves = Enable
100
TM
QuickScan
Lite QW2100
EAN Two Label
ENTER/EXIT PROGRAMMING MODE
EAN Two Label
EAN Two Label Enable/Disable
When disabled, the reader will not read EAN two label bar codes.
$CN2EN00
DEFAULT
EAN Two Label = Disable
$CN2EN01
EAN Two Label = Enable
EAN Two Label Combined Transmission
This feature enables/disables transmission of an EAN two label pair as one label. tHE LABEL
TYPE FOR ean TWO LABEL PAIRS IS ean 13.
$CN2CT00
DEFAULT
EAN Two Label = Disable
$CN2CT01
EAN Two Label = Enable
Product Reference Guide
101
Symbologies
ENTER/EXIT PROGRAMMING MODE
EAN Two Label Minimum Reads
This feature specifies the minimum number of consecutive times an EAN two label bar code
must be decoded before it is accepted as good read.
$CN2MR01
DEFAULT
EAN 8 Minimum Reads = 1
$CN2MR02
EAN 8 Minimum Reads = 2
$CN2MR03
EAN 8 Minimum Reads = 3
$CN2MR04
EAN 8 Minimum Reads = 4
102
TM
QuickScan
Lite QW2100
UPC/EAN Global Settings
ENTER/EXIT PROGRAMMING MODE
UPC/EAN Global Settings
This section provides configuration settings for UPC-A, UPC-E, EAN 13 and EAN 8 symbologies, and affects all of these unless otherwise marked for each feature description.
UPC/EAN Decoding Level
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs. See Decoding Levels on
page 267 for more detailed programming instructions.
$CUNDL01
UPC/EAN Decoding Level = 1
$CUNDL02
DEFAULT
UPC/EAN Decoding Level = 2
$CUNDL03
UPC/EAN Decoding Level = 3
$CUNDL04
UPC/EAN Decoding Level = 4
$CUNDL05
UPC/EAN Decoding Level = 5
Product Reference Guide
103
Symbologies
ENTER/EXIT PROGRAMMING MODE
UPC/EAN Global Settings — cont.
UPC/EAN Correlation
When correlation is enabled, the bar code reader will combine label data from multiple scans
when decoding. Enabling correlation will help the reader read labels that have some spots and/or
voids. It may also help read labels that have damaged areas. Enabling correlation will also
increase the chances that a label will be read incorrectly.
$CUNCO00
DEFAULT
UPC/EAN Correlation = Disable
$CUNCO01
UPC/EAN Correlation = Enable
104
TM
QuickScan
Lite QW2100
UPC/EAN Global Settings
ENTER/EXIT PROGRAMMING MODE
UPC/EAN Global Settings — cont.
UPC/EAN Price Weight Check
This feature enables/disables calculation and verification of price/weight check digits.
Options are
•
Disabled
•
Enable 4-digit price-weight check-digit calculation
•
Enable 5-digit price-weight check-digit calculation
•
Enable European 4-digit price-weight check-digit calculation
•
Enable European 5-digit price-weight check-digit calculation
$CPWEN00
DEFAULT
Price Weight Check = Disabled
$CPWEN01
Price Weight Check = 4-digit price-weight check
$CPWEN02
Price Weight Check = 5-digit price-weight check
$CPWEN03
Price Weight Check = European 4-digit price-weight check
$CPWEN04
Price Weight Check = European 5-digit price-weight check
Product Reference Guide
105
Symbologies
ENTER/EXIT PROGRAMMING MODE
UPC/EAN Global Settings — cont.
UPC-A Minimum Reads
This feature specifies the minimum number of consecutive times a UPC-A label must be
decoded before it is accepted as good read.
$CABMR01
DEFAULT
UPC-A Minimum Reads = 1
$CABMR02
UPC-A Minimum Reads = 2
$CABMR03
UPC-A Minimum Reads = 3
$CABMR04
UPC-A Minimum Reads = 4
106
TM
QuickScan
Lite QW2100
UPC/EAN Global Settings
ENTER/EXIT PROGRAMMING MODE
UPC/EAN Global Settings — cont.
UPC/EAN Guard Insertion
Enables/disables the ability to insert either a missing leading or trailing guard on an otherwise
complete UPC-A/EAN-13 segment.
The segment must have the structure GddddddCdddddd or
ddddddCddddddG.
NOTE
$CUNG100
DEFAULT
UPC/EAN Guard Insertion = Disable
$CUNG101
UPC/EAN Guard Insertion = Enable
UPC/EAN Stitch Exact Label Halves
Enables/disables the ability to stitch exact UPC-A/EAN 13 label halves with no overlapping
characters.
The label halves being stitched together to assemble a complete label must have the structure GddddddC and CddddddG.
NOTE
$CUNSE00
DEFAULT
UPC/EAN Stitch Exact Label Halves = Disable
$CUNSE01
UPC/EAN Stitch Exact Label Halves = Enable
Product Reference Guide
107
Symbologies
ENTER/EXIT PROGRAMMING MODE
UPC/EAN Global Settings — cont.
UPC/EAN Stitch Unlike Label Halves
Enables/disables the ability to stitch two UPC-A/EAN 13 label halves together that may have
differing characters in them.
The label half structures must have the structure GddddddC
and CddddddG. The characters dCd must match between the
two segments.
NOTE
$CUNSU00
DEFAULT
UPC/EAN Stitch Unlike Label Halves = Disable
$CUNSU01
UPC/EAN Stitch Unlike Label Halves = Enable
108
TM
QuickScan
Lite QW2100
UPC/EAN Global Settings
ENTER/EXIT PROGRAMMING MODE
UPC/EAN Global Settings — cont.
UPC/EAN Minimum Segment Length
Specifies the minimum number of characters necessary in an UPC/EAN/JAN label segment in
order for the reader to accept the segment for decoding.
$CUNSL05
DEFAULT
UPC/EAN Minimum Segment Length Block = 5
$CUNSL06
UPC/EAN Minimum Segment Length Block = 6
$CUNSL07
UPC/EAN Minimum Segment Length Block = 7
$CUNSL08
UPC/EAN Minimum Segment Length Block = 8
$CUNSL09
UPC/EAN Minimum Segment Length Block = 9
$CUNSL0A
UPC/EAN Minimum Segment Length Block = 10
Product Reference Guide
109
Symbologies
ENTER/EXIT PROGRAMMING MODE
UPC/EAN Global Settings — cont.
UPC/EAN Minimum Segment Length — cont.
$CUNSL0B
UPC/EAN Minimum Segment Length Block = 11
$CUNSL0C
UPC/EAN Minimum Segment Length Block = 12
$CUNSL0D
UPC/EAN Minimum Segment Length Block = 13
$CUNSL0E
UPC/EAN Minimum Segment Length Block = 14
$CUNSL0F
UPC/EAN Minimum Segment Length Block = 15
110
TM
QuickScan
Lite QW2100
Add-Ons
ENTER/EXIT PROGRAMMING MODE
Add-Ons
The following features apply to optional add-ons.
Contact Customer Support for advanced programming of
optional and conditional add-ons.
NOTE
Optional Add-ons
The reader can be enabled to optionally read the following add-ons (supplementals):
•
P2
•
P5
•
GS1-128
If a UPC/EAN base label and a an add-on are both decoded, the
reader will transmit the base label and add-on. If a UPC/EAN
base label is decoded without an add-on, the base label will be
transmitted without an add-on.
NOTE
Conditional add-on settings (if enabled) are considered by the
reader before optional add-on settings.
$CADO200
DEFAULT
Optional Add-Ons = Disable P2
$CADO201
Optional Add-Ons = Enable P2
$CADO500
DEFAULT
Optional Add-Ons = Disable P5
Product Reference Guide
111
Symbologies
ENTER/EXIT PROGRAMMING MODE
Add-Ons — cont.
Optional Add-ons — cont.
$CADO501
Optional Add-Ons = Enable P5
$CADO800
DEFAULT
Optional Add-Ons = Disable GS1-128
$CADO801
Optional Add-Ons = Enable GS1-128
112
TM
QuickScan
Lite QW2100
Add-Ons
ENTER/EXIT PROGRAMMING MODE
Add-Ons — cont.
Optional Add-On Timer
This option sets the time the reader will look for an add-on when an add-on fragment has been
seen and optional add-ons are enabled.
$CADOT01
Optional Add-on Timer = 10ms
$CADOT02
Optional Add-on Timer = 20ms
$CADOT03
Optional Add-on Timer = 30ms
$CADOT04
Optional Add-on Timer = 40ms
$CADOT05
Optional Add-on Timer = 50ms
Product Reference Guide
113
Symbologies
ENTER/EXIT PROGRAMMING MODE
Add-Ons — cont.
Optional Add-On Timer — cont.
$CADOT06
Optional Add-on Timer = 60ms
$CADOT07
DEFAULT
Optional Add-on Timer = 70ms
$CADOT0A
Optional Add-on Timer = 100ms
$CADOT0C
Optional Add-on Timer = 120ms
$CADOT0E
Optional Add-on Timer = 140ms
$CADOT10
Optional Add-on Timer = 160ms
114
TM
QuickScan
Lite QW2100
Add-Ons
ENTER/EXIT PROGRAMMING MODE
Add-Ons — cont.
P2 Add-Ons Minimum Reads
This feature specifies the minimum number of times a P2 add-on must be read before it is
marked as valid and then combined with a base label.
$CADM201
P2 Add-Ons Minimum Reads = 1
$CADM202
DEFAULT
P2 Add-Ons Minimum Reads = 2
$CADM203
P2 Add-Ons Minimum Reads = 3
$CADM204
P2 Add-Ons Minimum Reads = 4
Product Reference Guide
115
Symbologies
ENTER/EXIT PROGRAMMING MODE
Add-Ons — cont.
P5 Add-Ons Minimum Reads
This feature specifies the minimum number of times a P5 add-on must be read before it is
marked as valid and then combined with a base label.
$CADM501
DEFAULT
P5 Add-Ons Minimum Reads = 1
$CADM502
P5 Add-Ons Minimum Reads = 2
$CADM503
P5 Add-Ons Minimum Reads = 3
$CADM504
P5 Add-Ons Minimum Reads = 4
116
TM
QuickScan
Lite QW2100
Add-Ons
ENTER/EXIT PROGRAMMING MODE
Add-Ons — cont.
GS1-128 Add-Ons Minimum Reads
This feature specifies the minimum number of times an GS1-128 add-on must be read before it
is marked as valid and then combined with a base label.
$CADM801
DEFAULT
GS1-128 Add-Ons Minimum Reads = 1
$CADM802
GS1-128 Add-Ons Minimum Reads = 2
$CADM803
GS1-128 Add-Ons Minimum Reads = 3
$CADM804
GS1-128 Add-Ons Minimum Reads = 4
Product Reference Guide
117
Symbologies
ENTER/EXIT PROGRAMMING MODE
GS1 DataBar Omnidirectional
TM
The following options apply to the GS1 DataBar Omnidirectional (formerly RSS-14) symbology.
GS1 DataBar Omnidirectional Enable/Disable
When disabled, the reader will not read GS1 DataBar Omnidirectional bar codes.
$C4BEN00
DEFAULT
GS1 DataBar Omnidirectional = Disable
$C4BEN01
GS1 DataBar Omnidirectional = Enable
GS1 DataBar Omnidirectional GS1-128 Emulation
When enabled, GS1 DataBar Omnidirectional bar codes will be translated to the GS1-128 label
data format.
$C4BU800
DEFAULT
GS1 DataBar Omnidirectional GS1-128 Emulation = Disable
$C4BU801
GS1 DataBar Omnidirectional GS1-128 Emulation = Enable
118
TM
QuickScan
Lite QW2100
GS1 DataBar
TM
Omnidirectional
ENTER/EXIT PROGRAMMING MODE
GS1 DataBarTM Omnidirectional — cont.
GS1 DataBar Omnidirectional Minimum Reads
This feature specifies the minimum number of consecutive times a GS1 DataBar Omnidirectional label must be decoded before it is accepted as good read.
$C4BMR01
DEFAULT
GS1 DataBar Omnidirectional Minimum Reads = 1
$C4BMR02
GS1 DataBar Omnidirectional Minimum Reads = 2
$C4BMR03
GS1 DataBar Omnidirectional Minimum Reads = 3
$C4BMR04
GS1 DataBar Omnidirectional Minimum Reads = 4
Product Reference Guide
119
Symbologies
ENTER/EXIT PROGRAMMING MODE
GS1 DataBar Expanded
TM
The following options apply to the GS1 DataBar Expanded (formerly RSS Expanded) symbology.
GS1 DataBar Expanded Enable/Disable
When disabled, the reader will not read GS1 DataBar Expanded bar codes.
$CXBEN00
DEFAULT
GS1 DataBar Expanded = Disable
$CXBEN01
GS1 DataBar Expanded = Enable
GS1 DataBar Expanded GS1-128 Emulation
When enabled, GS1 DataBar Expanded bar codes will be translated to the GS1-128 label data
format.
$CXBU800
DEFAULT
GS1 DataBar Expanded GS1-128 Emulation = Disable
$CXBU801
GS1 DataBar Expanded GS1-128 Emulation = Enable
120
TM
QuickScan
Lite QW2100
GS1 DataBar
TM
Expanded
ENTER/EXIT PROGRAMMING MODE
GS1 DataBarTM Expanded — cont.
GS1 DataBar Expanded Minimum Reads
This feature specifies the minimum number of consecutive times a GS1 DataBar Expanded
label must be decoded before it is accepted as good read.
$CXBMR01
DEFAULT
GS1 DataBar Expanded Minimum Reads = 1
$CXBMR02
GS1 DataBar Expanded Minimum Reads = 2
$CXBMR03
GS1 DataBar Expanded Minimum Reads = 3
$CXBMR04
GS1 DataBar Expanded Minimum Reads = 4
Product Reference Guide
121
Symbologies
ENTER/EXIT PROGRAMMING MODE
GS1 DataBarTM Expanded — cont.
GS1 DataBar Expanded Length Control
This feature specifies either variable length decoding or fixed length decoding for the GS1
DataBar Expanded symbology.
Variable Length— For variable-length decoding, a minimum length may be set.
Fixed Length— For fixed-length decoding, two different lengths may be set.
$CXBLC00
DEFAULT
GS1 DataBar Expanded Length Control = Variable Length
$CXBLC01
GS1 DataBar Expanded Length Control = Fixed Length
122
TM
QuickScan
Lite QW2100
GS1 DataBar
TM
Expanded
ENTER/EXIT PROGRAMMING MODE
GS1 DataBarTM Expanded — cont.
GS1 DataBar Expanded Set Length 1
This feature specifies one of the bar code lengths for GS1 DataBar Expanded Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed
length if in Fixed Length Mode. Length includes the bar code’s data characters only.
The length can be set from 1 to 74 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CXBL1
Select GS1 DataBar Expanded Set Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
01 = Length 1 is 1 Character
123
Symbologies
ENTER/EXIT PROGRAMMING MODE
GS1 DataBarTM Expanded — cont.
GS1 DataBar Expanded Set Length 2
This feature specifies one of the bar code lengths for GS1 DataBar Expanded Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed
length if in Fixed Length Mode. Length includes the bar code’s data characters only.
The length can be set from 1 to 74 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CXBL2
Select GS1 DataBar Expanded Set Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
124
74 = Length 2 is 74 Characters
TM
QuickScan
Lite QW2100
TM
GS1 DataBar
Limited
ENTER/EXIT PROGRAMMING MODE
GS1 DataBar Limited
TM
The following options apply to the GS1 DataBar Limited (formerly RSS Limited) symbology.
GS1 DataBar Limited Enable/Disable
When disabled, the reader will not read GS1 DataBar Limited bar codes.
$CLBEN00
DEFAULT
GS1 DataBar Limited = Disable
$CLBEN01
GS1 DataBar Limited = Enable
GS1 DataBar Limited GS1-128 Emulation
When enabled, GS1 DataBar Limited bar codes will be translated to the GS1-128 label data format.
$CLBU800
DEFAULT
GS1 DataBar Limited GS1-128 Emulation = Disable
$CLBU801
GS1 DataBar Limited GS1-128 Emulation = Enable
Product Reference Guide
125
Symbologies
ENTER/EXIT PROGRAMMING MODE
GS1 DataBarTM Limited — cont.
GS1 DataBar Limited Minimum Reads
This feature specifies the minimum number of consecutive times a GS1 DataBar Limited label
must be decoded before it is accepted as good read.
$CLBMR01
DEFAULT
GS1 DataBar Limited Minimum Reads = 1
$CLBMR02
GS1 DataBar Limited Minimum Reads = 2
$CLBMR03
GS1 DataBar Limited Minimum Reads = 3
$CLBMR04
GS1 DataBar Limited Minimum Reads = 4
126
TM
QuickScan
Lite QW2100
Code 39
ENTER/EXIT PROGRAMMING MODE
Code 39
The following options apply to the Code 39 symbology.
Code 39 Enable/Disable
When disabled, the reader will not read Code 39 bar codes.
$CC3EN00
Code 39 = Disable
$CC3EN01
DEFAULT
Code 39 = Enable
Product Reference Guide
127
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Check Character Calculation
Enable this option to enable/disable calculation and verification of an optional Code 39 check
character. When disabled, any check character in the label is treated as a data character.
$CC3CC00
DEFAULT
Code 39 Check Character Calculation = Don’t Calculate
$CC3CC01
Code 39 Check Character Calculation = Calculate Std Check
$CC3CC02
Code 39 Check Character Calculation = Calculate Mod 7
Check
$CC3CC04
Code 39 Check Character Calculation = Enable Italian Post
Check
$CC3CC03
Code 39 Check Character Calculation = Enable Daimler
Chrysler Check
128
TM
QuickScan
Lite QW2100
Code 39
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Check Character Transmission
Enable this option to transmit the check character along with Code 39 bar code data.
$CC3CT00
Code 39 Check Character Transmission = Don’t Send
$CC3CT01
DEFAULT
Code 39 Check Character Transmission = Send
Code 39 Start/Stop Character Transmission
Enable this option to enable/disable transmission of Code 39 start and stop characters.
$CC3SS00
DEFAULT
Code 39 Start/Stop Character Transmission = Don’t Transmit
$CC3SS01
Code 39 Start/Stop Character Transmission = Transmit
Product Reference Guide
129
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Full ASCII
In Code 39 decoding, this enables/disables the translation of Code 39 characters to Code 39
full-ASCII characters.
$CC3FA00
DEFAULT
Code 39 Full ASCII = Disable
$CC3FA01
Code 39 Full ASCII = Enable
130
TM
QuickScan
Lite QW2100
Code 39
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Quiet Zones
This feature specifies the number of quiet zones for Code 39 labels. Quiet zones are blank areas
at the ends of a bar code and are typically 10 times the width of the narrowest bar or space in the
label.
$CC3LO01
Code 39 Quiet Zones = Quiet Zone on one side
$CC3LO02
Code 39 Quiet Zones = Quiet Zones on two sides
$CC3LO03
DEFAULT
Code 39 Quiet Zones = Auto
$CC3LO04
Code 39 Quiet Zones = Virtual Quiet Zones on two sides
$CC3LO05
Code 39 Quiet Zones = Small Quiet Zones on two sides
Product Reference Guide
131
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Minimum Reads
This feature specifies the minimum number of consecutive times a Code 39 label must be
decoded before it is accepted as good read.
$CC3MR01
Code 39 Minimum Reads = 1
$CC3MR02
DEFAULT
Code 39 Minimum Reads = 2
$CC3MR03
Code 39 Minimum Reads = 3
$CC3MR04
Code 39 Minimum Reads = 4
132
TM
QuickScan
Lite QW2100
Code 39
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Decoding Level
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs. See Decoding Levels on
page 267 for more detailed programming instructions.
$CC3DL01
Code 39 Decoding Level = 1
$CC3DL02
Code 39 Decoding Level = 2
$CC3DL03
DEFAULT
Code 39 Decoding Level = 3
$CC3DL04
Code 39 Decoding Level = 4
$CC3DL05
Code 39 Decoding Level = 5
Product Reference Guide
133
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Length Control
This feature specifies either variable length decoding or fixed length decoding for the Code 39
symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CC3LC00
DEFAULT
Code 39 Length Control = Variable Length
$CC3LC01
Code 39 Length Control = Fixed Length
134
TM
QuickScan
Lite QW2100
Code 39
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Set Length 1
This feature specifies one of the bar code lengths for Code 39 Length Control. Length 1 is the
minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. Length includes the bar code’s data characters only.
The length can be set from 0 to 50 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CC3L1
Select Code 39 Set Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
02 = Length 1 is 2 Characters
135
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Set Length 2
This feature specifies one of the bar code lengths for Code 39 Length Control. Length 2 is the
maximum label length if in Variable Length Mode, or the second fixed length if in Fixed
Length Mode. Length includes the bar code’s check, data, and full-ASCII shift characters. The
length does not include start/stop characters.
The length can be set from 1 to 50 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CC3L2
Select Code 39Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
136
50 = Length 2 is 50 Characters
TM
QuickScan
Lite QW2100
Code 39
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Interdigit Ratio
This feature specifies the ratio between an intercharacter space and module for Code 39 labels.
$CC3IR00
Code 39 Interdigit Ratio = Disable
$CC3IR01
Code 39 Interdigit Ratio = 1
$CC3IR02
Code 39 Interdigit Ratio = 2
$CC3IR03
Code 39 Interdigit Ratio = 3
$CC3IR04
DEFAULT
Code 39 Interdigit Ratio = 4
$CC3IR05
Code 39 Interdigit Ratio = 5
Product Reference Guide
137
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Interdigit Ratio — cont.
$CC3IR06
Code 39 Interdigit Ratio = 6
$CC3IR07
Code 39 Interdigit Ratio = 7
$CC3IR08
Code 39 Interdigit Ratio = 8
$CC3IR09
Code 39 Interdigit Ratio = 9
$CC3IR0A
Code 39 Interdigit Ratio = 10
138
TM
QuickScan
Lite QW2100
Code 39
ENTER/EXIT PROGRAMMING MODE
Code 39 — cont.
Code 39 Character Correlation
When correlation is enabled, the bar code reader will combine label data from multiple scans
when decoding. Enabling correlation will help the reader read labels that have some spots and/or
voids. It may also help read labels that have damaged areas. Enabling correlation will also
increase the chances that a label will be read incorrectly.
$CC3CO00
DEFAULT
Code 39 Character Correlation = Disable
$CC3CO01
Code 39 Character Correlation = Enable
Code 39 Stitching
This option enables/disables stitching for Code 39 labels. When parts of a Code 39 bar code are
presented to the reader with this feature enabled, the bar code parts will be assembled by the
reader’s software, and the data will be decoded if all bar code proofing requirements are met.
$CC3ST00
Code 39 Stitching = Disable
$CC3ST01
DEFAULT
Code 39 Stitching = Enable
Product Reference Guide
139
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 32 (Italian Pharmaceutical)
The following options apply to the Code 32 symbology.
Code 32 Enable/Disable
When disabled, the reader will not read Code 32 bar codes.
$CP3EN00
DEFAULT
Code 32 = Disable
$CP3EN01
Code 32 = Enable
Code 32 Feature Setting Exceptions
The following features are set for Code 32 by using these Code 39 settings:
NOTE
140
Code 39 Quiet Zones on page 131
Code 39 Minimum Reads on page 132
Code 39 Decoding Level on page 133
Code 39 Interdigit Ratio on page 137
Code 39 Character Correlation on page 139
Code 39 Stitching on page 139
TM
QuickScan
Lite QW2100
Code 32 (Italian Pharmaceutical)
ENTER/EXIT PROGRAMMING MODE
Code 32 (Italian Pharmaceutical) — cont.
Code 32 Check Character Transmission
Enable this option to transmit the check character along with Code 32 bar code data.
$CP3CT00
DEFAULT
Code 32 Check Character Transmission = Don’t Send
$CP3CT01
Code 32 Check Character Transmission = Send
Code 32 Start/Stop Character Transmission
This option enables/disable transmission of Code 32 start and stop characters.
$CP3SS00
DEFAULT
Code 32 Start/Stop Character Transmission = Don’t Transmit
$CP3SS01
Code 32 Start/Stop Character Transmission = Transmit
Product Reference Guide
141
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 39 CIP (French Pharmaceutical)
The following options apply to the Code 39 CIP symbology.
Code 39 CIP Enable/Disable
Enables/Disables ability of the reader to decode Code 39 CIP labels.
$CCCEN00
DEFAULT
Code 39 CIP = Disable
$CCCEN01
Code 39 CIP = Enable
Code 128
The following options apply to the Code 128 symbology.
Code 128 Enable/Disable
When disabled, the reader will not read Code 128 bar codes.
$CC8EN00
Code 128 = Disable
$CC8EN01
DEFAULT
Code 128 = Enable
142
TM
QuickScan
Lite QW2100
Code 128
ENTER/EXIT PROGRAMMING MODE
Code 128 — cont.
Expand Code 128 to Code 39
This feature enables/disables expansion of Code 128 labels to Code 39 labels. When enabled,
the label identifier for a Code 128 label shall be set to Code 39 and all Code 39 formatting control shall be applied to the label.
$CC8C300
DEFAULT
Code 128 to Code 39 = Don’t Expand
$CC8C301
Code 128 to Code 39 = Expand
Code 128 Check Character Transmission
Enable this option to transmit the check character along with Code 128 bar code data.
$CC8CT00
DEFAULT
Code 128 Check Character Transmission = Don’t Send
$CC8CT01
Code 128 Check Character Transmission = Send
Product Reference Guide
143
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 128 — cont.
Code 128 Function Character Transmission
Enables/disables transmission of Code128 function characters 1, 2, 3, and 4.
$CC8TF00
DEFAULT
Code 128 Function Character Transmission = Don’t Send
$CC8TF01
Code 128 Function Character Transmission = Send
Code 128 Sub-Code Change Transmission
Enables/disables the transmission of “Sub-Code exchange” characters (NOT transmitted by
standard decoding).
$CC8SC00
DEFAULT
Code 128 Sub-Code Change Transmission = Disable
$CC8SC01
Code 128 Sub-Code Change Transmission = Enable
144
TM
QuickScan
Lite QW2100
Code 128
ENTER/EXIT PROGRAMMING MODE
Code 128 — cont.
Code 128 Quiet Zones
This feature specifies the number of quiet zones for Code 128 labels. Quiet zones are blank areas
at the ends of a bar code and are typically 10 times the width of the narrowest bar or space in the
label.
$CC8LO00
Code 128 Quiet Zones = No Quiet Zones
$CC8LO01
Code 128 Quiet Zones = Quiet Zone on one side
$CC8LO02
Code 128 Quiet Zones = Quiet Zones on two sides
$CC8LO03
DEFAULT
Code 128 Quiet Zones = Auto
$CC8LO04
Code 128 Quiet Zones = Virtual Quiet Zones on two sides
Product Reference Guide
145
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 128 — cont.
Code 128 Minimum Reads
This feature specifies the minimum number of consecutive times a Code 128 label must be
decoded before it is accepted as good read.
$CC8MR01
DEFAULT
Code 128 Minimum Reads = 1
$CC8MR02
Code 128 Minimum Reads = 2
$CC8MR03
Code 128 Minimum Reads = 3
$CC8MR04
Code 128 Minimum Reads = 4
146
TM
QuickScan
Lite QW2100
Code 128
ENTER/EXIT PROGRAMMING MODE
Code 128 — cont.
Code 128 Decoding Level
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs. See Decoding Levels on
page 267 for more detailed programming instructions.
$CC8DL01
Code 128 Decoding Level = 1
$CC8DL02
Code 128 Decoding Level = 2
$CC8DL03
DEFAULT
Code 128 Decoding Level = 3
$CC8DL04
Code 128 Decoding Level = 4
$CC8DL05
Code 128 Decoding Level = 5
Product Reference Guide
147
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 128 — cont.
Code 128 Length Control
This feature specifies either variable length decoding or fixed length decoding for the Code 128
symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CC8LC00
DEFAULT
Code 128 Length Control = Variable Length
$CC8LC01
Code 128 Length Control = Fixed Length
148
TM
QuickScan
Lite QW2100
Code 128
ENTER/EXIT PROGRAMMING MODE
Code 128 — cont.
Code 128 Set Length 1
This feature specifies one of the bar code lengths for Code 128 Length Control. Length 1 is
the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. Length includes the bar code’s data characters only.
The length can be set from 1 to 80 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CC8L1
Select Code 128 Set Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
01 = Length 1 is 1 Character
149
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 128 — cont.
Code 128 Set Length 2
This feature specifies one of the bar code lengths for Code 128 Length Control. Length 2 is
the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed
Length Mode. Length includes the bar code’s data characters only.
The length can be set from 1 to 80 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CC8L2
Select Code 128 Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
150
80 = Length 2 is 80 Characters
TM
QuickScan
Lite QW2100
Code 128
ENTER/EXIT PROGRAMMING MODE
Code 128 — cont.
Code 128 Character Correlation
When correlation is enabled, the bar code reader will combine label data from multiple scans
when decoding. Enabling correlation will help the reader read labels that have some spots and/or
voids. It may also help read labels that have damaged areas. Enabling correlation will also
increase the chances that a label will be read incorrectly.
$CC8CO00
DEFAULT
Code 128 Character Correlation = Disable
$CC8CO01
Code 128 Character Correlation = Enable
Code 128 Stitching
This option enables/disables stitching for Code 128 labels. When parts of a Code 128 bar code
are presented to the reader with this feature enabled, the bar code parts will be assembled by the
reader’s software, and the data will be decoded if all bar code proofing requirements are met.
$CC8ST00
Code 128 Stitching = Disable
$CC8ST01
DEFAULT
Code 128 Stitching = Enable
Product Reference Guide
151
Symbologies
ENTER/EXIT PROGRAMMING MODE
GS1-128
The following options apply to the GS1-128 symbology. (Also known as USS-128, GTIN-128,
UCC-128.)
GS1-128 Enable
This option enables/disables the ability of the reader to translate GS1-128 labels to the GS1-128
data format. Options are:
•
Transmit GS1-128 labels in Code 128 data format.
•
Transmit GS1-128 labels in GS1-128 data format.
•
Do not transmit GS1-128 labels.
$CU8EN00
DEFAULT
GS1-128 = Transmit in Code 128 data format
$CU8EN01
GS1-128 = Transmit in GS1-128 data format
$CU8EN02
GS1-128 = Do not transmit GS1-128 labels
152
TM
QuickScan
Lite QW2100
Interleaved 2 of 5 (I 2 of 5)
ENTER/EXIT PROGRAMMING MODE
Interleaved 2 of 5 (I 2 of 5)
The following options apply to the I 2 of 5 symbology.
I 2 of 5 Enable/Disable
When disabled, the reader will not read I 2 of 5 bar codes.
$CI2EN00
DEFAULT
I 2 of 5 = Disable
$CI2EN01
I 2 of 5 = Enable
Product Reference Guide
153
Symbologies
ENTER/EXIT PROGRAMMING MODE
Interleaved 2 of 5 (I 2 of 5) — cont.
I 2 of 5 Check Character Calculation
This option enables/disables calculation and verification of an optional I 2 of 5 check character.
$CI2CC00
DEFAULT
I 2 of 5 Check Character Calculation = Disable
$CI2CC01
I 2 of 5 Check Character Calculation = Check Standard
(Modulo 10)
$CI2CC02
I 2 of 5 Check Character Calculation = Check German Parcel
$CI2CC04
I 2 of 5 Check Character Calculation = Check DHL
$CI2CC08
I 2 of 5 Check Character Calculation = Check Daimler
Chrysler
$CI2CC10
I 2 of 5 Check Character Calculation = Check Bosch
When disabled, any check character in label is treated as a data character.
154
TM
QuickScan
Lite QW2100
Interleaved 2 of 5 (I 2 of 5)
ENTER/EXIT PROGRAMMING MODE
Interleaved 2 of 5 (I 2 of 5) — cont.
I 2 of 5 Check Character Calculation — cont.
$CI2CC20
I 2 of 5 Check Character Calculation = Check Italian Post
I 2 of 5 Check Character Transmission
Enable this option to transmit the check character along with I 2 of 5 bar code data.
$CI2CT00
I 2 of 5 Check Character Transmission = Don’t Send
$CI2CT01
DEFAULT
I 2 of 5 Check Character Transmission = Send
Product Reference Guide
155
Symbologies
ENTER/EXIT PROGRAMMING MODE
Interleaved 2 of 5 (I 2 of 5) — cont.
I 2 of 5 Minimum Reads
This feature specifies the minimum number of consecutive times an I 2 of 5 label must be
decoded before it is accepted as good read.
$CI2MR01
I 2 of 5 Minimum Reads = 1
$CI2MR02
DEFAULT
I 2 of 5 Minimum Reads = 2
$CI2MR03
I 2 of 5 Minimum Reads = 3
$CI2MR04
I 2 of 5 Minimum Reads = 4
156
TM
QuickScan
Lite QW2100
Interleaved 2 of 5 (I 2 of 5)
ENTER/EXIT PROGRAMMING MODE
Interleaved 2 of 5 (I 2 of 5) — cont.
I 2 of 5 Decoding Level
This configuration item applies to Interleaved 2 of 5, Datalogic 2 of 5
and Standard 2 of 5.
NOTE
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs. See Decoding Levels on
page 267 for more detailed programming instructions.
$CI2DL01
2 of 5 Decoding Level = 1
$CI2DL02
2 of 5 Decoding Level = 2
$CI2DL03
DEFAULT
2 of 5 Decoding Level = 3
$CI2DL04
2 of 5 Decoding Level = 4
$CI2DL05
2 of 5 Decoding Level = 5
Product Reference Guide
157
Symbologies
ENTER/EXIT PROGRAMMING MODE
Interleaved 2 of 5 (I 2 of 5) — cont.
I 2 of 5 Length Control
This feature specifies either variable length decoding or fixed length decoding for the I 2 of 5
symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CI2LC00
DEFAULT
I 2 of 5 Length Control = Variable Length
$CI2LC01
I 2 of 5 Length Control = Fixed Length
158
TM
QuickScan
Lite QW2100
Interleaved 2 of 5 (I 2 of 5)
ENTER/EXIT PROGRAMMING MODE
Interleaved 2 of 5 (I 2 of 5) — cont.
I 2 of 5 Set Length 1
This feature specifies one of the bar code lengths for I 2 of 5 Length Control. Length 1 is the
minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. The length includes the bar code’s check and data characters.
The length can be set from 2 to 50 characters in increments of two. See Set Length 1 on
page 268 for more detailed programming instructions.
$CI2L1
Select I 2 of 5 Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
06 = Length 1 is 6 Characters
159
Symbologies
ENTER/EXIT PROGRAMMING MODE
Interleaved 2 of 5 (I 2 of 5) — cont.
I 2 of 5 Set Length 2
This feature specifies one of the bar code lengths for I 2 of 5 Length Control. Length 2 is the
maximum label length if in Variable Length Mode, or the second fixed length if in Fixed
Length Mode. The length includes the bar code’s check and data characters.
The length can be set from 2 to 50 characters. A setting of 0 specifies to ignore this length (only
one fixed length). See Set Length 2 on page 269 for more detailed programming instructions.
$CI2L2
Select I 2 of 5 Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
160
50 = Length 2 is 50 Characters
TM
QuickScan
Lite QW2100
Interleaved 2 of 5 (I 2 of 5)
ENTER/EXIT PROGRAMMING MODE
Interleaved 2 of 5 (I 2 of 5) — cont.
I 2 of 5 Character Correlation
When correlation is enabled, the bar code reader will combine label data from multiple scans
when decoding. Enabling correlation will help the reader read labels that have some spots and/or
voids. It may also help read labels that have damaged areas. Enabling correlation will also
increase the chances that a label will be read incorrectly.
$CI2CO00
DEFAULT
I 2 of 5 Character Correlation = Disable
$CI2CO01
I 2 of 5 Character Correlation = Enable
I 2 of 5 Zero Pattern
Enables/disables ZERO-Digit decoding. This character does not represent any cipher. It allows
encoding of an odd number of ciphers with Interleaved 2 of 5. It must be enabled to decode
Code 2 of 5 CIP/HR.
$CI2ZP00
DEFAULT
I 2 of 5 Zero Pattern = Disable
$CI2ZP01
I 2 of 5 Zero Pattern = Enable
Product Reference Guide
161
Symbologies
ENTER/EXIT PROGRAMMING MODE
Interleaved 2 of 5 (I 2 of 5) — cont.
I 2 of 5 Stitching
This option enables/disables stitching for I 2 of 5 labels. When parts of a I 2 of 5 bar code are
presented to the reader with this feature enabled, the bar code parts will be assembled by the
reader’s software, and the data will be decoded if all bar code proofing requirements are met.
$CI2ST00
DEFAULT
I 2 of 5 Stitching = Disable
$CI2ST01
I 2 of 5 Stitching = Enable
Interleaved 2 of 5 CIP HR
The following options apply to the Interleaved 2 of 5 CIP HR symbology.
Interleaved 2 of 5 CIP HR Enable/Disable
Enables/Disables ability of reader to decode Interleaved 2 of 5 CIP HR labels.
$CCHEN00
DEFAULT
Interleaved 2 of 5 CIP HR = Disable
$CCHEN01
Interleaved 2 of 5 CIP HR = Enable
162
TM
QuickScan
Lite QW2100
Datalogic 2 of 5
ENTER/EXIT PROGRAMMING MODE
Datalogic 2 of 5
The following options apply to the Datalogic 2 of 5 symbology.
Datalogic 2 of 5 Enable/Disable
When disabled, the reader will not read Datalogic 2 of 5 bar codes.
$CD2EN00
DEFAULT
Datalogic 2 of 5 = Disable
$CD2EN01
Datalogic 2 of 5 = Enable
Product Reference Guide
163
Symbologies
ENTER/EXIT PROGRAMMING MODE
Datalogic 2 of 5 — cont.
Datalogic 2 of 5 Check Character Calculation
This option enables/disables calculation and verification of an optional Datalogic 2 of 5 check
character.
$CD2CC00
DEFAULT
Datalogic 2 of 5 Check Character Calculation = Disable
$CD2CC01
Datalogic 2 of 5 Check Character Calculation = Enable
Datalogic 2 of 5 Check Character Transmission
This option enables/disables transmission of an optional Datalogic 2 of 5 character.
$CD2CT00
DEFAULT
Datalogic 2 of 5 Check Character Transmission = Don’t
Send
$CD2CT01
Datalogic 2 of 5 Check Character Transmission = Send
164
TM
QuickScan
Lite QW2100
Datalogic 2 of 5
ENTER/EXIT PROGRAMMING MODE
Datalogic 2 of 5 — cont.
Datalogic 2 of 5 Minimum Reads
This feature specifies the minimum number of consecutive times an Datalogic 2 of 5 label must
be decoded before it is accepted as good read.
$CD2MR01
I 2 of 5 Minimum Reads = 1
$CD2MR02
DEFAULT
I 2 of 5 Minimum Reads = 2
$CD2MR03
I 2 of 5 Minimum Reads = 3
$CD2MR04
I 2 of 5 Minimum Reads = 4
Datalogic 2 of 5 Decoding Level
The Datalogic 2 of 5 Decoding Level feature is set using
I 2 of 5
Decoding Level on page 157.
NOTE
Product Reference Guide
165
Symbologies
ENTER/EXIT PROGRAMMING MODE
Datalogic 2 of 5 — cont.
Datalogic 2 of 5 Length Control
This feature specifies either variable length decoding or fixed length decoding for the Datalogic
2 of 5 symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CD2LC00
DEFAULT
Datalogic 2 of 5 Length Control = Variable Length
$CD2LC01
Datalogic 2 of 5 Length Control = Fixed Length
166
TM
QuickScan
Lite QW2100
Datalogic 2 of 5
ENTER/EXIT PROGRAMMING MODE
Datalogic 2 of 5 — cont.
Datalogic 2 of 5 Set Length 1
This feature specifies one of the bar code lengths for Datalogic 2 of 5 Length Control.
Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if
in Fixed Length Mode. The length includes the bar code’s check and data characters.
The length can be set from 2 to 50 characters in increments of two. See Set Length 1 on
page 268 for more detailed programming instructions.
$CD2L1
Select Datalogic 2 of 5 Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
06 = Length 1 is 6 Characters
167
Symbologies
ENTER/EXIT PROGRAMMING MODE
Datalogic 2 of 5 — cont.
Datalogic 2 of 5 Set Length 2
This feature specifies one of the bar code lengths for Datalogic 2 of 5 Length Control.
Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length
if in Fixed Length Mode. The length includes the bar code’s check and data characters.
The length can be set from 2 to 50 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CD2L2
Select Datalogic 2 of 5 Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
168
50 = Length 2 is 50 Characters
TM
QuickScan
Lite QW2100
Datalogic 2 of 5
ENTER/EXIT PROGRAMMING MODE
Datalogic 2 of 5 Interdigit Maximum Ratio
This feature specifies the maximum ratio between intercharacter space and module for Datalogic 2 of 5.
$CD2IR00
Datalogic 2 of 5 Interdigit Maximum Ratio = Disable
$CD2IR01
Datalogic 2 of 5 Interdigit Maximum Ratio = 1
$CD2IR02
Datalogic 2 of 5 Interdigit Maximum Ratio = 2
$CD2IR03
Datalogic 2 of 5 Interdigit Maximum Ratio = 3
$CD2IR04
DEFAULT
Datalogic 2 of 5 Interdigit Maximum Ratio = 4
$CD2IR05
Datalogic 2 of 5 Interdigit Maximum Ratio = 5
Product Reference Guide
169
Symbologies
ENTER/EXIT PROGRAMMING MODE
Datalogic 2 of 5 Interdigit Maximum Ratio — cont.
$CD2IR06
Datalogic 2 of 5 Interdigit Maximum Ratio = 6
$CD2IR07
Datalogic 2 of 5 Interdigit Maximum Ratio = 7
$CD2IR08
Datalogic 2 of 5 Interdigit Maximum Ratio = 8
$CD2IR09
Datalogic 2 of 5 Interdigit Maximum Ratio = 9
$CD2IR0A
Datalogic 2 of 5 Interdigit Maximum Ratio = 10
170
TM
QuickScan
Lite QW2100
Datalogic 2 of 5
ENTER/EXIT PROGRAMMING MODE
Datalogic 2 of 5 — cont.
Datalogic 2 of 5 Character Correlation
When correlation is enabled, the bar code reader will combine label data from multiple scans
when decoding. Enabling correlation will help the reader read labels that have some spots and/or
voids. It may also help read labels that have damaged areas. Enabling correlation will also
increase the chances that a label will be read incorrectly.
$CD2CO00
DEFAULT
I 2 of 5 Character Correlation = Disable
$CD2CO01
I 2 of 5 Character Correlation = Enable
Datalogic 2 of 5 Stitching
This option enables/disables stitching for Datalogic 2 of 5 labels. When parts of a Datalogic 2 of
5 bar code are presented to the reader with this feature enabled, the bar code parts will be assembled by the reader’s software, and the data will be decoded if all bar code proofing requirements
are met.
$CD2ST00
DEFAULT
Datalogic 2 of 5 Stitching = Disable
$CD2ST01
Datalogic 2 of 5 Stitching = Enable
Product Reference Guide
171
Symbologies
ENTER/EXIT PROGRAMMING MODE
Codabar
The following options apply to the Codabar symbology.
Codabar Enable/Disable
When disabled, the reader will not read Codabar bar codes.
$CCBEN00
DEFAULT
Codabar = Disable
$CCBEN01
Codabar = Enable
Codabar Check Character Calculation
Enable this option to enables/disables calculation and verification of an optional Codabar check
character. When disabled, any check characters in the label are treated as data characters.
$CCBCC00
DEFAULT
Codabar Check Character Calculation = Don’t Calculate
$CCBCC01
Codabar Check Character Calculation = Enable AIM standard check char.
$CCBCC02
Codabar Check Character Calculation = Enable Modulo 10
check char.
172
TM
QuickScan
Lite QW2100
Codabar
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Check Character Transmission
Enable this option to transmit the check character along with Codabar bar code data.
$CCBCT00
Codabar Check Character Transmission = Don’t Send
$CCBCT01
DEFAULT
Codabar Check Character Transmission = Send
Codabar Start/Stop Character Transmission
Enable this option to enable/disable transmission of Codabar start and stop characters.
$CCBSS00
Codabar Start/Stop Character Transmission = Don’t Transmit
$CCBSS01
DEFAULT
Codabar Start/Stop Character Transmission = Transmit
Product Reference Guide
173
Symbologies
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Start/Stop Character Set
This option specifies the format of transmitted Codabar start/stop characters.
$CCBSC00
Codabar Check Character Set = ABCD/TN*E
$CCBSC01
Codabar Check Character Set = ABCD/ABCD
$CCBSC02
Codabar Check Character Set = abcd/tn*e
$CCBSC03
DEFAULT
Codabar Check Character Set = abcd/abcd
174
TM
QuickScan
Lite QW2100
Codabar
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Start/Stop Character Match
When enabled, this option requires that start and stop characters match.
$CCBSM00
DEFAULT
Codabar Start/Stop Character Match = Don’t Require
Match
$CCBSM01
Codabar Start/Stop Character Match = Require Match
Product Reference Guide
175
Symbologies
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Quiet Zones
This feature specifies the number of quiet zones for Codabar labels. Quiet zones are blank areas
at the ends of a bar code and are typically 10 times the width of the narrowest bar or space in the
label.
$CCBLO01
Codabar Quiet Zones = Quiet Zone on one side
$CCBLO02
Codabar Quiet Zones = Quiet Zones on two sides
$CCBLO03
DEFAULT
Codabar Quiet Zones = Auto
$CCBLO04
Codabar Quiet Zones = Virtual Quiet Zones on two sides
$CCBLO05
Codabar Quiet Zones = Small Quiet Zones on two sides
176
TM
QuickScan
Lite QW2100
Codabar
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Minimum Reads
This feature specifies the minimum number of consecutive times a Codabar label must be
decoded before it is accepted as good read.
$CCBMR01
Codabar Minimum Reads = 1
$CCBMR02
DEFAULT
Codabar Minimum Reads = 2
$CCBMR03
Codabar Minimum Reads = 3
$CCBMR04
Codabar Minimum Reads = 4
Product Reference Guide
177
Symbologies
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Decoding Level
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs. See Decoding Levels on
page 267 for more detailed programming instructions.
$CCBDL01
Codabar Decoding Level = 1
$CCBDL02
Codabar Decoding Level = 2
$CCBDL03
DEFAULT
Codabar Decoding Level = 3
$CCBDL04
Codabar Decoding Level = 4
$CCBDL05
Codabar Decoding Level = 5
178
TM
QuickScan
Lite QW2100
Codabar
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Length Control
This feature specifies either variable length decoding or fixed length decoding for the Codabar
symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CCBLC00
DEFAULT
Codabar Length Control = Variable Length
$CCBLC01
Codabar Length Control = Fixed Length
Product Reference Guide
179
Symbologies
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Set Length 1
This feature specifies one of the bar code lengths for Codabar Length Control. Length 1 is
the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. Length includes the bar code’s start, stop, check and data characters. The length
must include at least one data character.
The length can be set from 3 to 50 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CCBL1
Select Codabar Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
180
03 = Length 1 is 3 Characters
TM
QuickScan
Lite QW2100
Codabar
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Set Length 2
This feature specifies one of the bar code lengths for Codabar Length Control. Length 2 is
the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed
Length Mode. The length includes the bar code’s start, stop, check and data characters. The
length must include at least one data character.
The length can be set from 3 to 50 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CCBL2
Select CodabarLength 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
50 = Length 2 is 50 Characters
181
Symbologies
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Interdigit Ratio
This feature specifies the ratio between an intercharacter space and module for Codabar labels.
$CCBIR00
Codabar Interdigit Ratio = Disable
$CCBIR01
Codabar Interdigit Ratio = 1
$CCBIR02
Codabar Interdigit Ratio = 2
$CCBIR03
Codabar Interdigit Ratio = 3
$CCBIR04
DEFAULT
Codabar Interdigit Ratio = 4
$CCBIR05
Codabar Interdigit Ratio = 5
182
TM
QuickScan
Lite QW2100
Codabar
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Interdigit Ratio — cont.
$CCBIR06
Codabar Interdigit Ratio = 6
$CCBIR07
Codabar Interdigit Ratio = 7
$CCBIR08
Codabar Interdigit Ratio = 8
$CCBIR09
Codabar Interdigit Ratio = 9
$CCBIR0A
Codabar Interdigit Ratio = 10
Product Reference Guide
183
Symbologies
ENTER/EXIT PROGRAMMING MODE
Codabar — cont.
Codabar Character Correlation
When correlation is enabled, the bar code reader will combine label data from multiple scans
when decoding. Enabling correlation will help the reader read labels that have some spots and/or
voids. It may also help read labels that have damaged areas. Enabling correlation will also
increase the chances that a label will be read incorrectly.
$CCBCO00
DEFAULT
Codabar Character Correlation = Disable
$CCBCO01
Codabar Character Correlation = Enable
Codabar Stitching
This option enables/disables stitching for Codabar labels. When parts of a Codabar bar code are
presented to the reader with this feature enabled, the bar code parts will be assembled by the
reader’s software, and the data will be decoded if all bar code proofing requirements are met.
$CCBST00
DEFAULT
Codabar Stitching = Disable
$CCBST01
Codabar Stitching = Enable
184
TM
QuickScan
Lite QW2100
ABC Codabar
ENTER/EXIT PROGRAMMING MODE
ABC Codabar
The following options apply to the ABC Codabar symbology.
ABC Codabar Enable/Disable
Enables/Disables ability of reader to decode ABC Codabar labels.
$CCBAB00
DEFAULT
ABC Codabar = Disable
$CCBAB01
ABC Codabar = Enable
ABC Codabar Concatenation Mode
Specifies the concatenation mode between Static and Dynamic.
$CCBCM00
DEFAULT
ABC Codabar Concatenation Mode = Static
$CCBCM01
ABC Codabar Concatenation Mode = Dynamic
Product Reference Guide
185
Symbologies
ENTER/EXIT PROGRAMMING MODE
ABC Codabar — cont.
ABC Codabar Dynamic Concatenation Timeout
Specifies the timeout in 10-millisecond ticks used by the ABC Codabar Dynamic Concatenation Mode.
$CCBDT05
ABC Codabar Dynamic Concatenation Timeout = 50 msec
$CCBDT0A
ABC Codabar Dynamic Concatenation Timeout = 100 msec
$CCBDT14
DEFAULT
ABC Codabar Dynamic Concatenation Timeout = 200
msec
$CCBDT32
ABC Codabar Dynamic Concatenation Timeout = 500 msec
$CCBDT4B
ABC Codabar Dynamic Concatenation Timeout = 750
msec
$CCBDT64
ABC Codabar Dynamic Concatenation Timeout = 1 Second
186
TM
QuickScan
Lite QW2100
Code 11
ENTER/EXIT PROGRAMMING MODE
ABC Codabar — cont.
ABC Codabar Force Concatenation
Forces labels starting or ending with D to be concatenated.
$CCBFC00
DEFAULT
ABC Codabar Force Concatenation = Disable
$CCBFC01
ABC Codabar Force Concatenation = Enable
Code 11
The following options apply to the Code 11 symbology.
Code 11 Enable/Disable
When disabled, the reader will not read Code 11 bar codes.
$CC1EN00
DEFAULT
Code 11 = Disable
$CC1EN01
Code 11 = Enable
Product Reference Guide
187
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 11 — cont.
Code 11 Check Character Calculation
This option enables/disables calculation and verification of optional Code 11 check character.
$CC1CC00
Code 11 Check Character Calculation = Disable
$CC1CC01
Code 11 Check Character Calculation = Check C
$CC1CC02
Code 11 Check Character Calculation = Check K
$CC1CC03
DEFAULT
Code 11 Check Character Calculation = Check C and K
Code 11 Check Character Transmission
This feature enables/disables transmission of an optional Code 11 check character.
$CC1CT00
Code 11 Check Character Transmission = Don’t Send
$CC1CT01
DEFAULT
Code 11 Check Character Transmission = Send
188
TM
QuickScan
Lite QW2100
Code 11
ENTER/EXIT PROGRAMMING MODE
Code 11 — cont.
Code 11 Minimum Reads
This feature specifies the minimum number of consecutive times a Code 11 label must be
decoded before it is accepted as good read.
$CC1MR01
Code 11 Minimum Reads = 1
$CC1MR02
DEFAULT
Code 11 Minimum Reads = 2
$CC1MR03
Code 11 Minimum Reads = 3
$CC1MR04
Code 11 Minimum Reads = 4
Product Reference Guide
189
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 11 — cont.
Code 11 Length Control
This feature specifies either variable length decoding or fixed length decoding for the Code 11
symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CC1LC00
DEFAULT
Code 11 Length Control = Variable Length
$CC1LC01
Code 11 Length Control = Fixed Length
190
TM
QuickScan
Lite QW2100
Code 11
ENTER/EXIT PROGRAMMING MODE
Code 11 — cont.
Code 11 Set Length 1
This feature specifies one of the bar code lengths for Code 11 Length Control. Length 1 is the
minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. Length includes the bar code’s check and data characters.
The length can be set from 2 to 50 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CC1L1
Select Code 11 Set Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
04 = Length 1 is 4 Characters
191
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 11 — cont.
Code 11 Set Length 2
This feature specifies one of the bar code lengths for Code 11 Length Control. Length 2 is the
maximum label length if in Variable Length Mode, or the second fixed length if in Fixed
Length Mode. Length includes the bar code’s check and data characters.
The length can be set from 2 to 50 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CC1L2
Select Code 11 Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
192
50 = Length 2 is 50 Characters
TM
QuickScan
Lite QW2100
Code 11
ENTER/EXIT PROGRAMMING MODE
Code 11 — cont.
Code 11 Interdigit Ratio
This feature specifies the ratio between an intercharacter space and module for Code 11 labels.
$CC1IR00
Code 11 Interdigit Ratio = Disable
$CC1IR01
Code 11 Interdigit Ratio = 1
$CC1IR02
Code 11 Interdigit Ratio = 2
$CC1IR03
Code11 Interdigit Ratio = 3
$CC1IR04
DEFAULT
Code 11 Interdigit Ratio = 4
$CC1IR05
Code 11 Interdigit Ratio = 5
Product Reference Guide
193
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 11 — cont.
Code 11 Interdigit Ratio — cont.
$CC1IR06
Code 11 Interdigit Ratio = 6
$CC1IR07
Code 11 Interdigit Ratio = 7
$CC1IR08
Code 11 Interdigit Ratio = 8
$CC1IR09
Code 11 Interdigit Ratio = 9
$CC1IR0A
Code 11 Interdigit Ratio = 10
194
TM
QuickScan
Lite QW2100
Code 11
ENTER/EXIT PROGRAMMING MODE
Code 11 Decoding Level
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs. See Decoding Levels on
page 267 for more detailed programming instructions.
$CC1DL01
Codabar Decoding Level = 1
$CC1DL02
Codabar Decoding Level = 2
$CC1DL03
DEFAULT
Codabar Decoding Level = 3
$CC1DL04
Codabar Decoding Level = 4
$CC1DL05
Codabar Decoding Level = 5
Product Reference Guide
195
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 11 — cont.
Code 11 Character Correlation
When correlation is enabled, the bar code reader will combine label data from multiple scans
when decoding. Enabling correlation will help the reader read labels that have some spots and/or
voids. It may also help read labels that have damaged areas. Enabling correlation will also
increase the chances that a label will be read incorrectly.
$CC1CO00
DEFAULT
Code 11 Character Correlation = Disable
$CC1CO01
Code 11 Character Correlation = Enable
Code 11 Stitching
This option enables/disables stitching for Code 11 labels. When parts of a Code 11 bar code are
presented to the reader with this feature enabled, the bar code parts will be assembled by the
reader’s software, and the data will be decoded if all bar code proofing requirements are met.
$CC1ST00
DEFAULT
Code 11 Stitching = Disable
$CC1ST01
Code 11 Stitching = Enable
196
TM
QuickScan
Lite QW2100
Standard 2 of 5
ENTER/EXIT PROGRAMMING MODE
Standard 2 of 5
The following options apply to the Standard 2 of 5 symbology.
Standard 2 of 5 Enable/Disable
When disabled, the reader will not read Standard 2 of 5 bar codes.
$CS2EN00
DEFAULT
Standard 2 of 5 = Disable
$CS2EN01
Standard 2 of 5 = Enable
Standard 2 of 5 Check Character Calculation
This option enables/disables calculation and verification of an optional Standard 2 of 5 check
character.
$CS2CC00
DEFAULT
Standard 2 of 5 Check Character Calculation = Disable
$CS2CC01
Standard 2 of 5 Check Character Calculation = Enable
Product Reference Guide
197
Symbologies
ENTER/EXIT PROGRAMMING MODE
Standard 2 of 5 — cont.
Standard 2 of 5 Check Character Transmission
This feature enables/disables transmission of an optional Standard 2 of 5 check character.
$CS2CT00
Standard 2 of 5 Check Character Transmission = Don’t
Send
$CS2CT01
DEFAULT
Standard 2 of 5 Check Character Transmission = Send
Standard 2 of 5 Minimum Reads
This feature specifies the minimum number of consecutive times a Standard 2 of 5 label must be
decoded before it is accepted as good read.
$CS2MR01
Standard 2 of 5 Minimum Reads = 1
$CS2MR02
DEFAULT
Standard 2 of 5 Minimum Reads = 2
$CS2MR03
Standard 2 of 5 Minimum Reads = 3
$CS2MR04
Standard 2 of 5 Minimum Reads = 4
198
TM
QuickScan
Lite QW2100
Standard 2 of 5
ENTER/EXIT PROGRAMMING MODE
Standard 2 of 5 — cont.
Standard 2 of 5 Decoding Level
The Standard 2 of 5 Decoding Level feature is set using
I 2 of 5
Decoding Level on page 157.
NOTE
Standard 2 of 5 Length Control
This feature specifies either variable length decoding or fixed length decoding for the Standard 2
of 5 symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CS2LC00
DEFAULT
Standard 2 of 5 Length Control = Variable Length
$CS2LC01
Standard 2 of 5 Length Control = Fixed Length
Product Reference Guide
199
Symbologies
ENTER/EXIT PROGRAMMING MODE
Standard 2 of 5 — cont.
Standard 2 of 5 Set Length 1
This feature specifies one of the bar code lengths for Standard 2 of 5 Length Control. Length
1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. Length includes the bar code’s check and data characters.
The length can be set from 1 to 50 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CS2L1
Select Standard 2 of 5 Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
200
08 = Length 1 is 8 Characters
TM
QuickScan
Lite QW2100
Standard 2 of 5
ENTER/EXIT PROGRAMMING MODE
Standard 2 of 5 — cont.
Standard 2 of 5 Set Length 2
This feature specifies one of the bar code lengths for Standard 2 of 5 Length Control. Length
2 is the maximum label length if in Variable Length Mode, or the second fixed length if in
Fixed Length Mode. Length includes the bar code’s check and data characters.
The length can be set from 1 to 50 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CS2L2
Select Standard 2 of 5 Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
50 = Length 2 is 50 Characters
201
Symbologies
ENTER/EXIT PROGRAMMING MODE
Standard 2 of 5 — cont.
Standard 2 of 5 Character Correlation
When correlation is enabled, the bar code reader will combine label data from multiple scans
when decoding. Enabling correlation will help the reader read labels that have some spots and/or
voids. It may also help read labels that have damaged areas. Enabling correlation will also
increase the chances that a label will be read incorrectly.
$CS2CO00
DEFAULT
Standard 2 of 5 Character Correlation = Disable
$CS2CO01
Standard 2 of 5 Character Correlation = Enable
Standard 2 of 5 Stitching
This option enables/disables stitching for Standard 2 of 5 labels. When parts of a Standard 2 of
5 bar code are presented to the reader with this feature enabled, the bar code parts will be assembled by the reader’s software, and the data will be decoded if all bar code proofing requirements
are met.
$CS2ST00
DEFAULT
Standard 2 of 5 Stitching = Disable
$CS2ST01
Standard 2 of 5 Stitching = Enable
202
TM
QuickScan
Lite QW2100
Industrial 2 of 5
ENTER/EXIT PROGRAMMING MODE
Industrial 2 of 5
The following options apply to the Industrial 2 of 5 symbology.
Industrial 2 of 5 Enable/Disable
Enables/Disables ability of reader to decode Industrial 2 of 5 labels.
$CU2EN00
DEFAULT
Industrial 2 of 5 = Disable
$CU2EN01
Industrial 2 of 5 = Enable
Industrial 2 of 5 Check Character Calculation
Enables/Disables calculation and verification of an optional Industrial 2 of 5 check character.
$CU2CC00
DEFAULT
Industrial 2 of 5 Check Character Calculation = Disable
$CU2CC01
Industrial 2 of 5 Check Character Calculation = Enable
Product Reference Guide
203
Symbologies
ENTER/EXIT PROGRAMMING MODE
Industrial 2 of 5 — cont.
Industrial 2 of 5 Check Character Transmission
Enables/disables transmission of an Industrial 2 of 5 check character.
$CU2CT00
Industrial 2 of 5 Check Character Transmission = Disable
$CU2CT01
DEFAULT
Industrial 2 of 5 Check Character Transmission = Enable
Industrial 2 of 5 Length Control
This feature specifies either variable length decoding or fixed length decoding for the Industrial
2 of 5 symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CU2LC00
DEFAULT
Industrial 2 of 5 Length Control = Variable Length
$CU2LC01
Industrial 2 of 5 = Fixed Length
204
TM
QuickScan
Lite QW2100
Industrial 2 of 5
ENTER/EXIT PROGRAMMING MODE
Industrial 2 of 5 — cont.
Industrial 2 of 5 Set Length 1
This feature specifies one of the bar code lengths for Industrial 2 of 5 Length Control. Length
1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. Length includes the bar code’s data characters only.
The length can be set from 1 to 50 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CU2L1
Select Industrial 2 of 5 Set Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
01 = Length 1 is 1 Character
205
Symbologies
ENTER/EXIT PROGRAMMING MODE
Industrial 2 of 5 — cont.
Industrial 2 of 5 Set Length 2
This feature specifies one of the bar code lengths for Industrial 2 of 5 Length Control. Length
2 is the maximum label length if in Variable Length Mode, or the second fixed length if in
Fixed Length Mode. Length includes the bar code’s check, data, and full-ASCII shift characters. The length does not include start/stop characters.
The length can be set from 1 to 50 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CU2L2
Select Industrial 2 of5 Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
206
50 = Length 2 is 50 Characters
TM
QuickScan
Lite QW2100
Industrial 2 of 5
ENTER/EXIT PROGRAMMING MODE
Industrial 2 of 5 — cont.
Industrial 2 of 5 Minimum Reads
This feature specifies the minimum number of consecutive times an Industrial 2 of 5 label must
be decoded before it is accepted as good read.
$CU2MR01
DEFAULT
Industrial 2 of 5 Minimum Reads = 1
$CU2MR02
Industrial 2 of 5 Minimum Reads = 2
$CU2MR03
Industrial 2 of 5 Minimum Reads = 3
$CU2MR04
Industrial 2 of 5 Minimum Reads = 4
Product Reference Guide
207
Symbologies
ENTER/EXIT PROGRAMMING MODE
Industrial 2 of 5 — cont.
Industrial 2 of 5 Stitching
Enables/disables fixed length stitching for Industrial 2 of 5.
$CU2ST00
DEFAULT
Industrial 2 of 5 Stitching = Disable
$CU2ST01
Industrial 2 of 5 Stitching = Enable
Industrial 2 of 5 Character Correlation
Enable/disables character correlation for Industrial 2 of 5.
$CU2CO00
DEFAULT
Industrial 2 of 5 Character Correlation = Disable
$CU2CO01
Industrial 2 of 5 Character Correlation = Enable
208
TM
QuickScan
Lite QW2100
IATA
ENTER/EXIT PROGRAMMING MODE
IATA
The following options apply to the IATA symbology.
IATA Enable/Disable
Enables/Disables the ability of the reader to decode IATA labels.
$CIAEN00
DEFAULT
IATA = Disable
$CIAEN01
IATA = Enable
IATA Check Character Transmission
Enables/Disables calculation and verification of an optional Industrial 2 of 5 check character.
$CIACT00
IATA Check Character Transmission = Disable
$CIACT01
DEFAULT
IATA Check Character Transmission = Enable
Product Reference Guide
209
Symbologies
ENTER/EXIT PROGRAMMING MODE
ISBT 128
The following options apply to the ISBT 128 symbology.
ISBT 128 Concatenation
Enables/disables ISBT128 concatenation of 2 labels.
$CI8CE00
DEFAULT
ISBN 128 Concatenation = Disable
$CI8CE01
ISBN 128 Concatenation = Enable
ISBT 128 Concatenation Mode
Specifies the concatenation mode between Static and Dynamic.
This option is only valid when
210).
ISBT 128 Concatenation is enabled (see page
NOTE
$CI8CM00
DEFAULT
ISBT 128 Concatenation Mode = Static
$CI8CM01
ISBT 128 Concatenation Mode = Dynamic
210
TM
QuickScan
Lite QW2100
ISBT 128
ENTER/EXIT PROGRAMMING MODE
ISBT 128 — cont.
ISBT 128 Dynamic Concatenation Timeout
Specifies the timeout used by the ISBT 128 Dynamic Concatenation Mode.
$CI8DT05
ISBT 128 Dynamic Concatenation Timeout = 50 msec
$CI8DT0A
ISBT 128 Dynamic Concatenation Timeout = 100 msec
$CI8DT14
DEFAULT
ISBT 128 Dynamic Concatenation Timeout = 200 msec
$CI8DT32
ISBT 128 Dynamic Concatenation Timeout = 500 msec
$CI8DT4B
ISBT 128 Dynamic Concatenation Timeout = 750 msec
$CI8DT64
ISBT 128 Dynamic Concatenation Timeout = 1 second
Product Reference Guide
211
Symbologies
ENTER/EXIT PROGRAMMING MODE
ISBT 128 — cont.
ISBT 128 Force Concatenation
When enabled, this feature forces all ISBT 128 labels to be concatenated.
This option is only valid when
enabled. (see page 210).
ISBT 128 Concatenation is
NOTE
$CI8FC00
DEFAULT
ISBT 128 Force Concatenation = Disable
$CI8FC01
ISBT 128 Force Concatenation = Enable
ISBT 128 Advanced Concatenation Options
Use the Datalogic Aladdin configuration application or Contact
Customer Support to set up pairs of label types for concatenation.
NOTE
212
TM
QuickScan
Lite QW2100
MSI
ENTER/EXIT PROGRAMMING MODE
MSI
The following options apply to the MSI symbology.
MSI Enable/Disable
Enables/Disables ability of reader to decode MSI labels.
$CMSEN00
DEFAULT
MSI = Disable
$CMSEN01
MSI = Enable
MSI Check Character Calculation
Enables/Disables calculation and verification of an optional MSI check character.
$CMSCC00
MSI Check Character Calculation = Disable
$CMSCC01
DEFAULT
MSI Check Character Calculation = Enable Mod10
$CMSCC02
MSI Check Character Calculation = Enable Mod11/10
$CMSCC03
MSI Check Character Calculation = Enable Mod10/10
Product Reference Guide
213
Symbologies
ENTER/EXIT PROGRAMMING MODE
MSI — cont.
MSI Check Character Transmission
Enables/disables transmission of an MSI check character.
$CMSCT00
MSI Check Character Transmission = Disable
$CMSCT01
DEFAULT
MSI Check Character Transmission = Enable
MSI Length Control
This feature specifies either variable length decoding or fixed length decoding for the MSI symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CMSLC00
DEFAULT
MSI Length Control = Variable Length
$CMSLC01
MSI = Fixed Length
214
TM
QuickScan
Lite QW2100
MSI
ENTER/EXIT PROGRAMMING MODE
MSI — cont.
MSI Set Length 1
This feature specifies one of the bar code lengths for MSI Length Control. Length 1 is the
minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. Length includes the bar code’s data characters only.
The length can be set from 01 to 50 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CMSL1
Select MSI Set Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
01 = Length 1 is 1 Character
215
Symbologies
ENTER/EXIT PROGRAMMING MODE
MSI — cont.
MSI Set Length 2
This feature specifies one of the bar code lengths for MSI Length Control. Length 2 is the
maximum label length if in Variable Length Mode, or the second fixed length if in Fixed
Length Mode. Length includes the bar code’s check, data, and full-ASCII shift characters. The
length does not include start/stop characters.
The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only
one fixed length). See Set Length 2 on page 269 for more detailed programming instructions.
$CMSL2
Select MSI Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
216
50 = Length 2 is 50 Characters
TM
QuickScan
Lite QW2100
MSI
ENTER/EXIT PROGRAMMING MODE
MSI — cont.
MSI Minimum Reads
This feature specifies the minimum number of consecutive times an MSI label must be decoded
before it is accepted as good read.
$CMSMR01
MSI Minimum Reads = 1
$CMSMR02
MSI Minimum Reads = 2
$CMSMR03
MSI Minimum Reads = 3
$CMSMR04
DEFAULT
MSI Minimum Reads = 4
Product Reference Guide
217
Symbologies
ENTER/EXIT PROGRAMMING MODE
MSI — cont.
MSI Decoding Level
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs. See Decoding Levels on
page 267 for more detailed programming instructions.
$CMSDL00
MSI Decoding Level = Disable
$CMSDL01
MSI Decoding Level = 1
$CMSDL02
MSI Decoding Level = 2
$CMSDL03
DEFAULT
MSI Decoding Level = 3
$CMSDL04
MSI Decoding Level = 4
$CMSDL05
MSI Decoding Level = 5
218
TM
QuickScan
Lite QW2100
Code 93
ENTER/EXIT PROGRAMMING MODE
Code 93
The following options apply to the Code 93 symbology.
Code 93 Enable/Disable
Enables/Disables ability of reader to decode Code 93 labels.
$CC9EN00
DEFAULT
Code 93 = Disable
$CC9EN01
Code 93 = Enable
Code 93 Check Character Calculation
Enables/disables calculation and verification of an optional Code 93 check character.
$CC9CC00
Code 93 Check Character Calculation = Disable
$CC9CC01
Code 93 Check Character Calculation = Enable Check C
$CC9CC02
Code 93 Check Character Calculation = Enable Check K
$CC9CC03
DEFAULT
Code 93 Check Character Calculation = Enable Check C
and K
Product Reference Guide
219
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 93 — cont.
Code 93 Check Character Transmission
Enables/disables transmission of an optional Code 93 check character.
$CC9CT00
Code 93 Check Character Transmission = Disable
$CC9CT01
DEFAULT
Code 93 Check Character Transmission = Enable
Code 93 Length Control
This feature specifies either variable length decoding or fixed length decoding for the Code 93
symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CC9LC00
DEFAULT
Code 93 Length Control = Variable Length
$CC9LC01
Code 93 = Fixed Length
220
TM
QuickScan
Lite QW2100
Code 93
ENTER/EXIT PROGRAMMING MODE
Code 93 — cont.
Code 93 Set Length 1
This feature specifies one of the bar code lengths for Code 93 Length Control. Length 1 is the
minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. Length includes the bar code’s data characters only.
The length can be set from 01 to 50 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CC9L1
Select Code 93 Set Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
01 = Length 1 is 1 Character
221
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 93 — cont.
Code 93 Set Length 2
This feature specifies one of the bar code lengths for Code 93 Length Control. Length 2 is the
maximum label length if in Variable Length Mode, or the second fixed length if in Fixed
Length Mode. Length includes the bar code’s check, data, and full-ASCII shift characters. The
length does not include start/stop characters.
The length can be set from 1 to 50 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CC9L2
Select Code 93 Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
222
50 = Length 2 is 50 Characters
TM
QuickScan
Lite QW2100
Code 93
ENTER/EXIT PROGRAMMING MODE
Code 93 — cont.
Code 93 Minimum Reads
This feature specifies the minimum number of consecutive times a Code 93 label must be
decoded before it is accepted as good read.
$CC9MR01
DEFAULT
Code 93 Minimum Reads = 1
$CC9MR02
Code 93 Minimum Reads = 2
$CC9MR03
Code 93 Minimum Reads = 3
$CC9MR04
Code 93 Minimum Reads = 4
Product Reference Guide
223
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 93 — cont.
Code 93 Decoding Level
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs. See Decoding Levels on
page 267 for more detailed programming instructions.
$CC9DL00
Code 93 Decoding Level = Disable
$CC9DL01
Code 93 Decoding Level = 1
$CC9DL02
Code 93 Decoding Level = 2
$CC9DL03
DEFAULT
Code 93 Decoding Level = 3
$CC9DL04
Code 93 Decoding Level = 4
$CC9DL05
Code 93 Decoding Level = 5
224
TM
QuickScan
Lite QW2100
Code 93
ENTER/EXIT PROGRAMMING MODE
Code 93 — cont.
Code 93 Quiet Zones
Enables/disables fixed length stitching for Code 93.
$CC9LO00
Code 93 Quiet Zones = No Quiet Zones
$CC9LO01
Code 93 Quiet Zones = Quiet Zone on one side
$CC9LO02
Code 93 Quiet Zones = Quiet Zones on two sides
$CC9LO03
DEFAULT
Code 93 Quiet Zones = Auto
$CC9LO04
Code 93 Quiet Zones = Virtual Quiet Zones on two sides
Product Reference Guide
225
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 93 — cont.
Code 93 Stitching
Disable/enable fixed or variable length stitching for Code 93.
$CC9ST00
Code 93 Stitching = Disable
$CC9ST01
DEFAULT
Code 93 Stitching = Enable
Code 93 Character Correlation
Enables/disables Character Correlation for Code 93.
$CC9CO00
Code 93 Character Correlation = Disable
$CC9CO01
DEFAULT
Code 93 Character Correlation = Enable
226
TM
QuickScan
Lite QW2100
Codablock F
ENTER/EXIT PROGRAMMING MODE
Codablock F
The following options apply to the Codablock F symbology.
Codablock F Enable/Disable
Enables/Disables the ability of the reader to decode Codablock F labels.
$CCFEN00
DEFAULT
Codablock F = Disable
$CCFEN01
Codablock F = Enable
Codablock F EAN Enable/Disable
Enables/Disables the Codablock F EAN subtype (code with FNC1 in the first position).
$CCFEA00
DEFAULT
Codablock F EAN = Disable
$CCFEA01
Codablock F EAN = Enable
Product Reference Guide
227
Symbologies
ENTER/EXIT PROGRAMMING MODE
Codablock F AIM Check
Specifies if Check Digit calculation algorithm is AIM compliant or not.
$CCFAC00
Codablock F AIM Check = Not AIM compliant
$CCFAC01
DEFAULT
Codablock F AIM Check = AIM compliant
Codablock F Length Control
This feature specifies either variable length decoding or fixed length decoding for the Codablock
F symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CCFLC00
DEFAULT
Codablock F Length Control = Variable Length
$CCFLC01
Codablock F = Fixed Length
228
TM
QuickScan
Lite QW2100
Codablock F
ENTER/EXIT PROGRAMMING MODE
Codablock F — cont.
Codablock F Set Length 1
This feature specifies one of the bar code lengths for Codablock F Length Control. Length 1
is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. Length includes the bar code’s data characters only.
The length can be set from 003 to 255 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CCFL1
Select Codablock F Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
003 = Length 1 is 3 Characters
229
Symbologies
ENTER/EXIT PROGRAMMING MODE
Codablock F — cont.
Codablock F Set Length 2
This feature specifies one of the bar code lengths for Codablock F Length Control. Length 2
is the maximum label length if in Variable Length Mode, or the second fixed length if in
Fixed Length Mode. Length includes the bar code’s check, data, and full-ASCII shift characters. The length does not include start/stop characters.
The length can be set from 3 to 255 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CCFL2
Select Codablock F Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
230
100 = Length 2 is 100 Characters
TM
QuickScan
Lite QW2100
Code 4
ENTER/EXIT PROGRAMMING MODE
Code 4
The following options apply to the Code 4 symbology.
Code 4 Enable/Disable
Enables/Disables ability of reader to decode Code 4 labels.
$CCREN00
DEFAULT
Code 4 = Disable
$CCREN01
Code 4 = Enable
Code 4 Check Character Transmission
This feature enables/disables transmission of an optional Code 4 check character.
$CCRCT00
Code 4 Check Character Transmission = Don’t Send
$CCRCT01
DEFAULT
Code 4 Check Character Transmission = Send
Product Reference Guide
231
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 4 — cont.
Code 4 Hex to Decimal Conversion
This feature enables/disables the conversion of hexidecimal label data to decimal label data.
$CCRHD00
Code 4 Hex to Decimal Conversion = Disable
$CCRHD01
DEFAULT
Code 4 Hex to Decimal Conversion = Enable
Code 5
The following options apply to the Code 5 symbology.
Code 5 Enable/Disable
Enables/Disables ability of reader to decode Code 5 labels.
$CC5EN00
DEFAULT
Code 5 = Disable
$CC5EN01
Code 5 = Enable
232
TM
QuickScan
Lite QW2100
Code 5
ENTER/EXIT PROGRAMMING MODE
Code 5 — cont.
Code 5 Check Character Transmission
This feature enables/disables transmission of an optional Code 5 check character.
$CC5CT00
Code 5 Check Character Transmission = Don’t Send
$CC5CT01
DEFAULT
Code 5 Check Character Transmission = Send
Code 5 Hex to Decimal Conversion
This feature enables/disables the conversion of hexidecimal label data to decimal label data.
$CC5HD00
Code 5 Hex to Decimal Conversion = Disable
$CC5HD01
DEFAULT
Code 5 Hex to Decimal Conversion = Enable
Product Reference Guide
233
Symbologies
ENTER/EXIT PROGRAMMING MODE
Code 4 and Code 5 Common Configuration Items
The following options apply to both Code 4 and Code 5 symbologies.
Code 4 and 5 Decoding Level
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs. See Decoding Levels on
page 267 for more detailed programming instructions.
This configuration item applies to Code 4 and Code 5.
NOTE
$CC5DL01
Code 4 and Code 5 Decoding Level = 1
$CC5DL02
Code 4 and Code 5 Decoding Level = 2
$CC5DL03
DEFAULT
Code 4 and Code 5 Decoding Level = 3
$CC5DL04
Code 4 and Code 5 Decoding Level = 4
$CC5DL05
Code 4 and Code 5 Decoding Level = 5
234
TM
QuickScan
Lite QW2100
Code 4 and Code 5 Common Configuration Items
ENTER/EXIT PROGRAMMING MODE
Code 4 and Code 5 Common Configuration Items — cont.
Code 4 and Code 5 Minimum Reads
This feature specifies the minimum number of consecutive times a Code 4 or Code 5 label must
be decoded before it is accepted as good read.
$CC5MR01
DEFAULT
Code 4 or Code 5 Minimum Reads = 1
$CC5MR02
Code 4 or Code 5 Minimum Reads = 2
$CC5MR03
Code 4 or Code 5 Minimum Reads = 3
$CC5MR04
Code 4 or Code 5 Minimum Reads = 4
Product Reference Guide
235
Symbologies
ENTER/EXIT PROGRAMMING MODE
Follett 2 of 5
The following options apply to the Follett 2 of 5 symbology.
Follett 2 of 5 Enable/Disable
Enables/Disables ability of reader to decode Follett 2 of 5 labels.
$CF2EN00
DEFAULT
Follett 2 of 5 = Disable
$CF2EN01
Follett 2 of 5 = Enable
BC412
The following options apply to the BC412 symbology.
BC412 Enable/Disable
Enables/Disables ability of reader to decode BC412 labels.
$CBCEN00
DEFAULT
BC412 = Disable
$CBCEN01
BC412 = Enable
236
TM
QuickScan
Lite QW2100
BC412
ENTER/EXIT PROGRAMMING MODE
BC412 — cont.
BC412 Check Character Calculation
Enable this option to enable/disable calculation and verification of an optional BC412 check
character. When disabled, any check character in the label is treated as a data character.
$CBCCC00
DEFAULT
BC412 Check Character Calculation = Don’t Calculate
$CBCCC01
BC412 Check Character Calculation = Calculate Check
Character
Product Reference Guide
237
Symbologies
ENTER/EXIT PROGRAMMING MODE
BC412 — cont.
BC412 Minimum Reads
This feature specifies the minimum number of consecutive times a BC412 label must be
decoded before it is accepted as good read.
$CBCMR01
BC412 Minimum Reads = 1
$CBCMR02
DEFAULT
BC412 Minimum Reads = 2
$CBCMR03
BC412 Minimum Reads = 3
$CBCMR04
BC412 Minimum Reads = 4
238
TM
QuickScan
Lite QW2100
BC412
ENTER/EXIT PROGRAMMING MODE
BC412 — cont.
BC412 Decoding Level
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs. See Decoding Levels on
page 267 for more detailed programming instructions.
$CBCDL01
BC412 Decoding Level = 1
$CBCDL02
BC412 Decoding Level = 2
$CBCDL03
DEFAULT
BC412 Decoding Level = 3
$CBCDL04
BC412 Decoding Level = 4
$CBCDL05
BC412 Decoding Level = 5
Product Reference Guide
239
Symbologies
ENTER/EXIT PROGRAMMING MODE
BC412 — cont.
BC412 Length Control
This feature specifies either variable length decoding or fixed length decoding for the BC412
symbology.
Variable Length— For variable length decoding, a minimum and maximum length may be set.
Fixed Length— For fixed length decoding, two different lengths may be set.
$CBCLC00
DEFAULT
BC41‘2 Length Control = Variable Length
$CBCLC01
BC412 Length Control = Fixed Length
240
TM
QuickScan
Lite QW2100
BC412
ENTER/EXIT PROGRAMMING MODE
BC412 — cont.
BC412 Set Length 1
This feature specifies one of the bar code lengths for BC412 Length Control. Length 1 is the
minimum label length if in Variable Length Mode, or the first fixed length if in Fixed
Length Mode. Length includes the bar code’s data characters only.
The length can be set from 0 to 50 characters. See Set Length 1 on page 268 for more
detailed programming instructions.
$CBCL1
Select BC412 Set Length 1 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
Product Reference Guide
01 = Length 1 is 1 Character
241
Symbologies
ENTER/EXIT PROGRAMMING MODE
BC412 — cont.
BC412 Set Length 2
This feature specifies one of the bar code lengths for BC412 Length Control. Length 2 is the
maximum label length if in Variable Length Mode, or the second fixed length if in Fixed
Length Mode. Length includes the bar code’s check, data, and full-ASCII shift characters. The
length does not include start/stop characters.
The length can be set from 1 to 50 characters. A setting of 00 specifies to ignore this length
(only one fixed length). See Set Length 2 on page 269 for more detailed programming
instructions.
$CBCL2
Select Code 39Length 2 Setting
~
Make a mistake? Scan the CANCEL bar code to abort and
not save the entry string. You can then start again at the
beginning.
CANCEL
DEFAULT
242
50 = Length 2 is 50 Characters
TM
QuickScan
Lite QW2100
Chapter 11
References
This section contains explanations and examples of selected bar code features. See the programming sections for the actual bar code labels used to configure the reader.
Product Reference Guide
243
References
Label Gone Timeout
This feature sets the time after the last label segment is seen before the reader prepares for a new
label. The timeout can be set within a range of 10 milliseconds to 2,550 milliseconds (2.55 seconds) in 10ms increments. Label Gone Timeout does not apply to scan modes that require a
trigger pull for each label that is read
Follow these instructions to set this feature:
1. Determine the desired setting in milliseconds.
2. Divide the desired setting by 10 (setting is in 10ms increments). Pad the result with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005, 20 = 020, etc.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT LABEL GONE TIMEOUT SETTING.
5. Scan the appropriate three alpha-numeric characters from the keypad in Appendix E,
Keypad representing the duration which was determined in the steps above. You will hear
a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 2 for some examples of how to set this feature.
Table 2. Timeout Setting Examples
STEP
ACTION
1
Desired Setting
50ms
150ms
1800ms (1.8
sec.)
2550ms (2.55 sec.)
2
Divide by 10 (and pad with
leading zeroes)
005
015
180
255
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT LABEL GONE TIMEOUT SETTING
5
6
244
EXAMPLES
Scan Three Characters From
Appendix E, Keypad
‘0’, ‘0’ and ‘5’
‘0’, ‘1’ and ‘5’
‘1’, ‘8’ and ‘0’
‘‘2’, ‘5’ and ‘5’
Scan ENTER/EXIT PROGRAMMING MODE
TM
QuickScan
Lite QW2100
Good Read LED Duration
Good Read LED Duration
This feature specifies the amount of time that the Good Read LED remains on following a good
read. The good read LED on time can be set within a range of 0.1 to 25.5 seconds in 100ms
increments.
Follow these instructions to set this feature:
1. Determine the desired setting in milliseconds. A setting of 0 means that the good read
LED stays on until the next time the trigger is pulled.
2. Divide the desired setting by 100 (setting is in 100ms increments). Pad the result with
leading zeroes to yield three digits. For example: 0 = 000, 5 = 000, 20 = 020, etc.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT GOOD READ LED DURATION SETTING.
5. Scan the appropriate three digits from the keypad in Appendix E, Keypad representing
the duration which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 3 for some examples of how to set this feature.
Table 3. Good Read LED Duration Setting Examples
STEP
ACTION
EXAMPLES
1
Desired Setting
Good Read LED
stays on until
next trigger pull
(00)
2
Divide by 100 (and pad with
leading zeroes)
000
200ms
1500ms (1.5
sec.)
2500ms (2.5 sec.)
002
015
025
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT GOOD READ LED DURATION SETTING
5
Scan Three Characters From
Appendix E, Keypad
6
Product Reference Guide
‘0’, ‘0’ and ‘0’
‘0’, ‘0’ and ‘2’
‘0’, ‘1’ and ‘5’
‘0’, ‘2’ and ‘5’
Scan ENTER/EXIT PROGRAMMING MODE
245
References
Scan Mode
Selects the scan operating mode for the reader. Selections are:
Trigger Single— When the trigger is pulled, scanning is activated until one of the following
occurs:
- Scanning Active Time has elapsed
- a label has been read
- the trigger is released
This mode is associated with typical handheld reader operation: when the trigger is pulled, scanning starts and the product scans until the trigger is released, or a label is read, or the maximum
Scanning Active Time has elapsed.
Trigger Hold Multiple — When the trigger is pulled, scanning starts and the product scans until
the trigger is released or Scanning Active Time has elapsed. Reading a label does not disable
scanning. Double Read Timeout prevents undesired multiple reads of the same label while in
this mode.
Trigger Pulse Multiple— When the trigger is pulled, continuous scanning is activated until Scan-
ning Active Time has elapsed or the trigger has been released and pulled again. Double Read
Timeout prevents undesired multiple reads of the same label while in this mode.
1
Flashing— The reader flashes on and off regardless of the trigger status. Flash rate is controlled
by Flash On Time and Flash Off Time. When Flash is ON the reader reads continuously.
When Flash is OFF scanning is deactivated.
Always On— No trigger pull is required to read a bar code. Scanning is continually on. Double
Read Timeout prevents undesired multiple reads while in this mode.
®
Autosense Stand Mode— No trigger pull is required to read a bar code. Scanning is turned on
automatically when an item is placed in reader’s field of view. If the trigger is pulled, the reader
acts as if it in single read mode. Double Read Timeout prevents undesired multiple reads of
the same label while in this mode.
Trigger Object Sense— This mode is similar to Stand Mode, except that a trigger pull is required
to activate the decoder.
1. Controlled by Flash
246
On Time.
TM
QuickScan
Lite QW2100
Scanning Active Time
Scanning Active Time
This setting specifies the amount of time that the reader stays in scan ON state once the state is
entered. The range for this setting is from 1 to 255 seconds in 1-second increments.
Follow these instructions to set this feature:
1. Determine the desired setting.
2. Pad the result with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005, 20
= 020, etc.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT SCANNING ACTIVE TIME SETTING.
5. Scan the appropriate three digits from the keypad in Appendix E, Keypad, that represent the duration which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 4 for some examples of how to set this feature.
Table 4. Scanning Active Time Setting Examples
STEP
ACTION
EXAMPLES
1
Desired Setting
1 Second
90 Sec. (1.5
min.)
180 Sec. (3 min.)
255 Seconds (4.25
min.)
2
Pad leading zero(es)
001
090
180
255
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT SCANNING ACTIVE TIME SETTING
5
Scan Three Characters From
Appendix E, Keypad
6
Product Reference Guide
‘0’, ‘0’ and ‘1’
‘0’, ‘9’ and ‘0’
‘1’, ‘8’ and ‘0’
‘2’, ‘5’ and ‘5’
Scan ENTER/EXIT PROGRAMMING MODE
247
References
Flash On Time
This feature specifies the ON time for the indicator LED while in Flash Mode. The selectable
range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments.
Follow these instructions to set this feature.
1. Determine the desired setting in milliseconds.
2. Divide the desired setting by 100 (setting is in 100ms increments). Pad the result with
leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT FLASH ON TIME SETTING.
5. Scan the appropriate two digits from the keypad in Appendix E, Keypad representing
the duration which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 5 for some examples of how to set this feature.
Table 5. Flash On Time Setting Examples
STEP
ACTION
1
Desired Setting
500ms
1,000ms (1 sec.)
5200ms (5.2
sec.)
9,900ms (9.9 sec.)
2
Divide by 100 (and pad with
leading zeroes to yield two
digits)
05
10
52
99
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT FLASH ON TIME SETTING
5
6
248
EXAMPLES
Scan Two Characters From
Appendix E, Keypad
‘0’ and ‘5’
‘1’ and ‘0’
‘5’ and ‘2’
‘9’ and ‘9’
Scan ENTER/EXIT PROGRAMMING MODE
TM
QuickScan
Lite QW2100
Flash Off Time
Flash Off Time
This feature specifies the OFF time for the indicator LED while in Flash Mode. The selectable
range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments.
Follow these instructions to set this feature.
1. Determine the desired setting in milliseconds.
2. Divide the desired setting by 100 (setting is in 100ms increments). Pad the result with
leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT FLASH OFF TIME SETTING.
5. Scan the appropriate two digits from the keypad in Appendix E, Keypad, that represent
the duration which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 6 for some examples of how to set this feature.
Table 6. Flash Off Time Setting Examples
STEP
ACTION
EXAMPLES
1
Desired Setting
500ms
1,000ms (1 sec.)
5200ms (5.2
sec.)
9,900ms (9.9 sec.)
2
Divide by 100 (and pad with
leading zeroes to yield two
digits)
05
10
52
99
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT FLASH OFF TIME SETTING
5
Scan Two Characters From
Appendix E, Keypad
6
Product Reference Guide
‘0’ and ‘5’
‘1’ and ‘0’
‘5’ and ‘2’
‘9’ and ‘9’
Scan ENTER/EXIT PROGRAMMING MODE
249
References
Intercharacter Delay
This parameter specifies the intercharacter delay between the end of one character and the
beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in
10ms increments. A setting of zero specifies no delay.
To set the delay:
1. Determine the desired setting in milliseconds.
2. Divide the desired setting by 10 (setting is in 10ms increments). Pad the result with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT INTERCHARACTER DELAY SETTING.
5. Scan the appropriate two digits from the keypad in Appendix E, Keypad, that represent
the duration which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 2 for some examples of how to set this feature.
Table 7. Intercharacter Delay Setting Examples
STEP
ACTION
1
Desired Setting
50ms
150ms
600ms
850ms
2
Divide by 10 (and pad with
leading zeroes to yield twodigits)
05
15
60
85
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT INTERCHARACTER DELAY SETTING
5
6
250
EXAMPLES
Scan Two Characters From
Appendix E, Keypad
‘0’ and ‘5’
‘1’ and ‘5’
‘6’ and ‘0’
‘8’ and ‘5’
Scan ENTER/EXIT PROGRAMMING MODE
TM
QuickScan
Lite QW2100
ACK Character
ACK Character
This setting specifies an ASCII character or hex value to be used as the ACK character. ASCII
characters or any hex value from 0 to 0xFF can be selected.
NOTE
Setting to previously defined characters such as XON, XOFF,
or host commands conflicts with normal operation of these
characters. 8-bit data is not recognized when the option Data
Bits has been set as 7 Data Bits.
To set this feature:
1. Determine the desired character or value.
2. Use the ASCII Chart on the inside back cover of this manual to find the hex equivalent
for the desired character/value.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT ACK CHARACTER SETTING.
5. Scan the appropriate two alpha-numeric characters from the keypad in Appendix E,
Keypad, that represent the desired character/value in step 1 above. The second character
will cause a two-beep indication.
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 8 for some examples of how to set this feature.
Table 8. ACK Character Setting Examples
STEP
ACTION
EXAMPLES
1
Desired Character/Value
ACK
$
@
>
2
Hex equivalent
0x06
0x24
0x40
0x3E
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT ACK CHARACTER SETTING
5
Scan Two Characters From
Appendix E, Keypad
6
Product Reference Guide
‘0’ and ‘6’
‘2’ and ‘4’
‘4’ and ‘0’
‘3’ AND ‘E’
Scan ENTER/EXIT PROGRAMMING MODE
251
References
NAK Character
This setting specifies an ASCII character or hex value to be used as the NAK character. ASCII
characters or any hex value from 0 to 0xFF can be selected.
NOTE
Setting to previously defined characters such as XON, XOFF,
or host commands conflicts with normal operation of these
characters. 8-bit data is not recognized when the option Data
Bits has been set as 7 Data Bits.
To set this feature:
1. Determine the desired character or value.
2. Use the ASCII Chart on the inside back cover of this manual to find the hex equivalent
for the desired character/value.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT NAK CHARACTER SETTING.
5. Scan the appropriate two alpha-numeric characters from the keypad in Appendix E,
Keypad, that represent the desired character/value in step 1 above. The second character
will cause a two-beep indication.
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 9 for some examples of how to set this feature.
Table 9. NAK Character Setting Examples
STEP
ACTION
1
Desired Character/Value
NAK
$
@
>
2
Hex equivalent
0x15
0x24
0x40
0x3E
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT NAK CHARACTER SETTING
5
6
252
EXAMPLES
Scan Two Characters From
Appendix E, Keypad
‘1’ and ‘5’
‘2’ and ‘4’
‘4’ and ‘0’
‘3’ AND ‘E’
Scan ENTER/EXIT PROGRAMMING MODE
TM
QuickScan
Lite QW2100
ACK NAK Timeout Value
ACK NAK Timeout Value
This option specifies the amount of time the reader waits for an ACK character from the host
following label transmission. The selectable timeout range is 200 milliseconds to 15,000ms (15
seconds) in 200ms increments. A selection of 0 disables the timeout.
To set this value:
1. Determine the desired setting in milliseconds.
2. Divide the desired setting by 200 (setting is in 200ms increments). Pad the result with
leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT ACK NAK TIMEOUT VALUE SETTING.
5. Scan the appropriate two digits from the keypad in Appendix E, Keypad, that represent
the duration which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 6 for some examples of how to set this feature.
Table 10. ACK NAK Timeout Value Setting Examples
STEP
ACTION
EXAMPLES
1
Desired Setting
200ms
1,000ms (1 sec.)
5200ms (5.2
sec.)
15,000ms (1 sec.)
2
Divide by 200
01
05
26
75
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT ACK NAK TIMEOUT VALUE SETTING
5
Scan Two Characters From
Appendix E, Keypad
7
Product Reference Guide
‘0’ and ‘1’
‘0’ and ‘5’
‘2’ and ‘6’
‘7’ and ‘5’
Scan ENTER/EXIT PROGRAMMING MODE
253
References
ACK NAK Retry Count
This feature specifies the number of times the reader retries a label transmission due to a retry
condition. The selectable range is from 1 to 254 retries. A selection of 0 disables the count, and
a selection of 255 specifies unlimited retries.
To set this feature:
1. Determine the desired setting.
2. Pad the number with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005,
20 = 020, etc.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT ACK NAK RETRY COUNT SETTING.
5. Scan the appropriate three digits from the keypad in Appendix E, Keypad, that represent the number which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 11 for some examples of how to set this feature.
Table 11. ACK NAK Retry Count Setting Examples
STEP
ACTION
1
Desired Setting
Disable Retry
Count
3 Retries
54 Retries
Unlimited Retries
2
Pad with leading zero(es)
000
003
054
255
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT ACK NAK RETRY COUNT SETTING
5
6
254
EXAMPLES
Scan Three Characters From
Appendix E, Keypad
‘0’, ‘0’ and ‘0’
‘0’, ‘0’ and ‘3’
‘0’, ‘5’ and ‘4’
‘2’, ‘5’ and ‘5’
Scan ENTER/EXIT PROGRAMMING MODE
TM
QuickScan
Lite QW2100
Disable Character
Disable Character
Specifies the value of the RS-232 host command used to disable the reader.
ASCII characters or any hex value from 0 to 0xFF can be selected.
NOTE
Setting to previously defined characters such as XON, XOFF,
or host commands conflicts with normal operation of these
characters. 8-bit data is not recognized when the option Data
Bits has been set as 7 Data Bits.
To set the value:
1. Determine the desired character or value. A setting of 0xFF indicates the the Disable
Character is not used (not available).
2. Use the ASCII Chart on the inside back cover of this manual to find the hex equivalent
for the desired character/value.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT DISABLE CHARACTER SETTING.
5. Scan the appropriate two alpha-numeric characters from the keypad in Appendix E,
Keypad, that represent the desired character/value in step 1 above. The second character
will cause a two-beep indication.
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 12 for some examples of how to set this feature.
Table 12. Disable Character Setting Examples
STEP
ACTION
EXAMPLES
1
Desired character/value
‘d’
‘}’
‘D’
Disable Command
Not Used
2
Hex equivalent
0x64
0x7D
0x44
0xFF
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT DISABLE CHARACTER VALUE SETTING
5
Scan Two Characters From
Appendix E, Keypad
6
Product Reference Guide
‘6’ and ‘4’
‘7’ and ‘D’
‘4’ and ‘4’
‘F’ AND ‘F’
Scan ENTER/EXIT PROGRAMMING MODE
255
References
Enable Character
Specifies the value of the RS-232 host command used to enable the reader.
ASCII characters or any hex value from 0 to 0xFF can be selected.
NOTE
Setting to previously defined characters such as XON, XOFF,
or host commands conflicts with normal operation of these
characters. 8-bit data is not recognized when the option Data
Bits has been set as 7 Data Bits.
To set this feature:
Determine the desired character or value. A setting of 0xFF indicates the the Enable Character is
not used (not available).
1. Determine the desired character or value.
2. Use the ASCII Chart on the inside back cover of this manual to find the hex equivalent
for the desired character/value.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT ENABLE CHARACTER SETTING.
5. Scan the appropriate two alpha-numeric characters from the keypad in Appendix E,
Keypad, that represent the desired character/value in step 2 above. The second character
will cause a two-beep indication.
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 13 for some examples of how to set this feature.
Table 13. Enable Character Setting Examples
STEP
ACTION
1
Desired character/value
‘e’
‘}’
‘E’
Enable Command
Not Used
2
Hex equivalent
0x65
0x7D
0x45
0xFF
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT ENABLE CHARACTER VALUE SETTING
5
6
256
EXAMPLES
Scan Two Characters From
Appendix E, Keypad
‘6’ and ‘5’
‘7’ and ‘D’
‘4’ and ‘5’
‘F’ AND ‘F’
Scan ENTER/EXIT PROGRAMMING MODE
TM
QuickScan
Lite QW2100
Wedge Quiet Interval
Wedge Quiet Interval
This option specifies the amount of time to look for keyboard activity before the reader breaks
the keyboard connection in order to transmit data to host. The selectable range for this feature is
from 0 to 990ms in 10ms increments.
This feature applies ONLY to the Keyboard Wedge interface.
NOTE
Follow these instructions to set this feature:
1. Determine the desired setting in milliseconds.
2. Divide the desired setting by 10 (setting is in 10ms increments). Pad the result with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT WEDGE QUIET INTERVAL SETTING.
5. Scan the appropriate two digits from the keypad in Appendix E, Keypad, that represent
the duration which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure to set the Wedge Quiet Interval. See Table 2 for some examples
of how to set this feature.
Table 14. Timeout Setting Examples
STEP
ACTION
EXAMPLES
1
Desired Setting
10ms
150ms
600ms
850ms
2
Divide by 10 (and pad with
leading zeroes)
01
15
60
85
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT WEDGE QUIET INTERVAL SETTING
5
Scan Two Characters From
Appendix E, Keypad
6
Product Reference Guide
‘0’ and ‘1’
‘1’ and ‘5’
‘6’ and ‘0’
‘8’ and ‘5’
Scan ENTER/EXIT PROGRAMMING MODE
257
References
Intercharacter Delay
This parameter specifies the intercharacter delay between the end of one character and the
beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in
10ms increments. A setting of zero specifies no delay.
This feature applies ONLY to the Keyboard Wedge interface.
NOTE
To set the delay:
1. Determine the desired setting in milliseconds.
2. Divide the desired setting by 10 (setting is in 10ms increments). Pad the result with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc.
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT INTERCHARACTER DELAY SETTING.
5. Scan the appropriate two digits from the keypad in Appendix E, Keypad, that represent
the duration which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 2 for some examples of how to set this feature.
Table 15. Intercharacter Delay Setting Examples
STEP
ACTION
1
Desired Setting
50ms
150ms
600ms
850ms
2
Divide by 10 (and pad with
leading zeroes to yield twodigits)
05
15
60
85
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT INTERCHARACTER DELAY SETTING
5
6
258
EXAMPLES
Scan Two Characters From
Appendix E, Keypad
‘0’ and ‘5’
‘1’ and ‘5’
‘6’ and ‘0’
‘8’ and ‘5’
Scan ENTER/EXIT PROGRAMMING MODE
TM
QuickScan
Lite QW2100
Intercode Delay
Intercode Delay
Specifies the delay between labels transmitted to the host for this interface. The selectable range
for this feature is from 0 to 99 seconds.
Follow these instructions to set this feature:
1. Determine the desired setting.
2. Pad the number with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 =
20, etc
3. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
4. Scan the bar code: SELECT INTERCODE DELAY SETTING.
5. Scan the appropriate two digits from the keypad in Appendix E, Keypad, that represent
the duration which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 16 for some examples of how to set this feature.
Table 16. Wedge Intercode Delay Examples
STEP
ACTION
EXAMPLES
1
Desired Setting
No Delay
5 Seconds
60 Seconds
99 Seconds
2
Pad with leading zero(es)
00
05
60
99
3
Scan ENTER/EXIT PROGRAMMING MODE
4
Scan SELECT INTERCODE DELAY SETTING
5
Scan Two Characters From
Appendix E, Keypad
7
Product Reference Guide
‘0’ and ‘0’
‘0’ and ‘5’
‘6’ and ‘0’
‘9’ AND ‘9’
Scan ENTER/EXIT PROGRAMMING MODE
259
References
Global Prefix/Suffix
Up to 20 ASCII characters may be added as a prefix (in a position before the bar code data) and/
or as a suffix (in a position following the bar code data) as indicated in Figure 7.
Figure 7. Prefix and Suffix Positions
OR...
Prefix
Label ID
AIM ID
Bar Code Data
Label ID
Suffix
00 - 20 Characters (ASCII)
AND
OR
Example: Setting a Prefix
In this example, we’ll set a prefix for all symbologies.
1. Determine which ASCII character(s) are to be added to scanned bar code data. In this
example, we’ll add a dollar sign (‘$’) as a prefix.
2. Scan the ENTER/EXIT bar code.
3. Scan the SET GLOBAL PREFIX bar code.
4. Reference the ASCII Chart on the inside back cover of this manual, to find the hex value
assigned to the desired character. The corresponding hex number for the ‘$’ character is
24. To enter this selection code, scan the ‘2’ and ‘4’ bar codes from Appendix E, Keypad.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
5. If less than the expected string of 20 characters are selected, scan the ENTER/EXIT bar
code to terminate the string.
6. Scan the ENTER/EXIT bar code once again to exit Programming Mode.
7. The resulting message string would appear as follows:
Scanned bar code data:12345
Resulting message string output: $12345
This option sets up to 20 characters each from the set of ASCII characters or any hex value from
00 to FF. To configure this feature, scan the ENTER/EXIT bar code to place the unit in Programming Mode, then the “Set Global Prefix” or “Set Global Suffix,” bar code followed by the
digits (in hex) from the Alphanumeric characters in Appendix E, Keypad representing your
desired character(s). If less than the expected string of 20 characters are selected, scan the
ENTER/EXIT bar code to terminate the string. Reference the section, Example: Setting a
Prefix on page 260, for more information. Exit programming mode by scanning the
ENTER/EXIT bar code once again.
260
TM
QuickScan
Lite QW2100
Global AIM ID
Global AIM ID
This feature enables/disables addition of AIM IDs for all symbology types.
NOTE
AIM label identifiers (as opposed to custom characters you select yourself as with label identifiers) can be included with scanned bar code data. AIM label identifiers consist of three characters
as follows:
•
A close brace character (ASCII ‘]’), followed by...
•
A code character (see the table below), followed by...
•
A modifier character (the modifier character is symbol dependent).
SYMBOLOGY
CHA
R
a
SYMBOLOGY
CHA
R
UPC/EAN
E
Code 128/GS1-128
C
Code 39 and
Code 32
A
GS1 DataBar Omnidirectional, GS1 DataBar
Expanded
e
Codabar
F
Standard 2 of 5
S
Interleaved 2 of 5
I
ISBN
X
Code 93
G
Code 11
H
b
a. UPC-A and UPC-E labels are converted to EAN 13 when adding AIM IDs.
b. ISBN (X with a 0 modifier character)
Figure 8. AIM ID
Prefix
Product Reference Guide
Label ID
AIM ID
Bar Code Data
Label ID
Suffix
261
References
Label ID: Pre-loaded Sets
The following table lists the pre-loaded label ID sets for the USA and Europe.
Table 17. Label ID Pre-loaded Sets
Symbology
USA Label ID set
ASCII
character
Hex
value
ASCII
character
Hexidecimal
value
ABC Codabar
S
530000
S
530000
CODABAR
%
250000
R
520000
Codablock F
l
6C0000
m
6D0000
Code 39 CIP
Y
590000
Y
590000
Code 93
&
260000
U
550000
CODE11
CE
434500
b
620000
CODE128
#
230000
T
540000
CODE32
A
410000
X
580000
CODE39
*
2A0000
V
560000
CODE4
4
340000
4
340000
CODE5
j
6A0000
j
6A0000
CODE93
&
260000
U
550000
DATALOGIC 2OF5
s
730000
s
730000
EAN13
F
460000
B
420000
EAN13 P2
F
460000
L
4C0000
EAN13 P5
F
460000
M
4D0000
EAN13 P8
F
460000
#
230000
EAN8
FF
464600
A
410000
EAN8 P2
FF
464600
J
4A0000
EAN8 P5
FF
464600
K
4B0000
EAN8 P8
FF
464600
*
2A0000
FOLLETT 2OF5
O
4F0000
O
4F0000
GS1 DATABAR EXPANDED
RX
525800
t
740000
GS1 DATABAR LIMITED
RL
524C00
v
760000
GS1 DATABAR OMNIDIRECTIONAL
R4
523400
u
750000
000000
k
6B0000
i
690000
N
4E0000
IA
494100
&
260000
GS1-128
I2OF5
IATA
262
EU Label ID set
TM
QuickScan
Lite QW2100
Label ID: Pre-loaded Sets
Symbology
USA Label ID set
EU Label ID set
Industrial 2 of 5
W
570000
W
570000
Interleaved 2 of 5 CIP HR
e
650000
e
650000
ISBN
I
490000
@
400000
ISBT128
f
660000
f
660000
ISSN
n
6E0000
n
6E0000
MSI
@
400000
Z
5A0000
S25
s
730000
P
500000
UPCA
A
410000
C
430000
UPCA P2
A
410000
F
460000
UPCA P5
A
410000
G
470000
UPCA P8
A
410000
Q
510000
UPCE
E
450000
D
440000
UPCE P2
E
450000
H
480000
UPCE P5
E
450000
I
490000
UPCE P8
E
450000
E
450000
Product Reference Guide
263
References
Label ID: Set Individually Per Symbology
To configure a Label ID individually for a single symbology:
1. Scan the ENTER/EXIT bar code.
2. Select Label ID position as either BEFORE (Enable as Prefix) or AFTER (Enable as suffix) by scanning the appropriate bar code in the section Label ID Control on page 71.
Reference Figure 9 for Label ID positioning options if multiple identification features are
enabled.
3. Scan a bar code to select the symbology for which you wish to configure a custom Label
ID from the section Label ID Symbology Selection, starting on page 72.
4. Determine the desired character(s) (you may choose up to three) which will represent the
Label ID for the selected symbology.
5. Turn to the ASCII Chart on the inside back cover of this manual and find the equivalent
hex digits associated with your choice of Label ID. For example, if you wish to select an
equal sign (=) as a Label ID, the chart indicates its associated hex characters as 3D. Turn to
Keypad, starting on page 297 and scan the bar codes representing the hex characters
determined. For the example given, the characters ‘3’ and ‘D’ would be scanned. More
examples of Label ID settings are provided in Table 18.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
6. Scan the ENTER/EXIT bar code to exit Label ID entry.
7. Scan the ENTER/EXIT bar code once again to exit Programming Mode.
This completes the steps to configure a Label ID for a given symbology.
Figure 9. Label ID Position Options
Prefix
Label ID
Aim ID
Bar Code Data
Label ID
Suffix
OR
264
TM
QuickScan
Lite QW2100
Label ID: Set Individually Per Symbology
Label ID: Set Individually Per Symbology — continued
Table 18. Label ID Examples
STEP
ACTION
EXAMPLES
1.
Scan the ENTER/EXIT bar code
(Reader enters Programming Mode)
2.
Determine placement of the
Label ID characters BEFORE
or AFTER with regard to
Enable as Prefix Enable as Suffix Enable as Prefix
scanned data using Label ID
Enable as Suffix
Control on page 71
3.
4.
Scan the bar code selecting the
symbology type you wish to
designate label ID characters
for using Label ID
Symbology
Selection, starting on page
72.
Custom Label ID example
(desired characters):
GS1 DataBar
Omnidirectional
D B
*
Code 39
Interleaved 2 of
5
Code 32
= C 3
+
P H
3D 43 33
2B
50 48
Find hex equivalents from the
ASCII table (inside back cover),
then scan in these digits/
characters using the bar codes
in the section:
5.
Keypad, starting on page
297. f you make a mistake
44 42 2A
before the last character, scan
the CANCEL bar code to abort
and not save the entry string.
You can then start again at the
beginning.
6.
Scan theENTER/EXIT bar code
(Reader exits Label ID entry)
7.
Scan the ENTER/EXIT bar code
once again
(Reader exits Programming Mode)
Result:
Product Reference Guide
DB*[bar code
data]
[bar code
data]=C3
+[bar code data]
[bar code data]PH
265
References
Character Conversion
Character conversion is an eight byte configuration item. The eight bytes are 4 character pairs
represented in hexadecimal ASCII values. The first character in the pair is the character that will
be converted. The second character in the pair is the character to convert to. If the character to
convert in a pair is FF, then no conversion is done.
For example, if you have the character conversion configuration item set to the following:
41423132FFFFFFFF
The first pair is 4142 or AB (41 hex is an ASCII capital A, 42 hex is an ASCII capital B) and the
second pair is 3132 or 12 (31 hex is an ASCII 1, 32 is an ASCII 2). The other two pairs are
FFFF and FFFF.
With the label, AB12BA21, it would look as follows after the character
conversion: BB22BB22.
The A characters were converted to B characters and the 1 characters were converted to 2 characters. Nothing is done with the last two character pairs, since they are all FF.
To set Character Conversion:
1. Scan the ENTER/EXIT bar code.
2. Scan the “Configure Character Conversion” bar code.
3. Determine the desired string. Sixteen positions must be determined as in the above example. Next, turn to the ASCII Chart on the inside back cover of this manual and find the
equivalent hex digits needed to fulfill the string.
4. Turn to Appendix E, Keypad and scan the bar codes representing the hex characters
determined in the previous step.
5. Scan the ENTER/EXIT bar code to exit Programming Mode.
If less than the expected string of 16 characters are selected,
scan the ENTER/EXIT bar code twice to accept the selections
and exit Programming Mode.
NOTE
266
TM
QuickScan
Lite QW2100
Decoding Levels
Decoding Levels
Decoding Levels are used to configure a bar code symbology decoder to be very aggressive to
very conservative depending on a particular customer’s needs.
•
Choosing Level 1 results in a very conservative decoder at the expense of not being able to
read poorly printed or damaged labels.
•
Choosing Level 5 results in a very aggressive decoder. This aggressive behavior allows
decoding of poorly printed and damaged labels at the expense of increasing the likelihood
of decoding errors.
•
Choosing Level 3, which is the default setting, allows the majority of product labels to be
decoded.
There are many factors that determine when to change the decoding level for a particular symbology. These factors include spots, voids, non-uniform bar/space widths, damaged labels, etc.
that may be experienced in some bar code labels. If there are many hard to read or damaged
labels that cannot be decoded using a conservative setting, increase the decoding level to be
more aggressive. If the majority of labels are very good quality labels, or there is a need to
decrease the possibility of a decoder error, lower the decoding level to a more conservative level.
Product Reference Guide
267
References
Set Length 1
This feature specifies one of the bar code lengths for a given symbology. Length 1 is the minimum label length if in Varible Length Mode, or the first fixed length if in Fixed Length Mode.
Length includes the bar code’s data characters only.
Reference the Symbologies section to view the selectable range (number of characters) for the
symbology being set.
Follow these instructions to set this feature:
1. Determine the desired character length. Pad the number with leading zeroes to yield two
digits. For example: 0 = 00, 5 = 05, 20 = 20, etc.
2. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
3. Scan the “Select Length 1 Setting” for the symbology being set.
4. Scan the appropriate two digits from the keypad in Appendix E, Keypad, that represent
the length setting which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
5. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 2 for some examples of how to set this feature.
Table 19. Length 1 Setting Examples
STEP
ACTION
1
Desired Setting
01 Character
07 Characters
52 Characters
2
Scan ENTER/EXIT PROGRAMMING MODE
3
Scan SELECT LENGTH 1SETTING for the desired symbology
4
5
268
EXAMPLES
Scan Two Characters From
Appendix E, Keypad
‘0’ and ‘1’
‘0’ and ‘7’
‘5’ and ‘2’
74 Characters
‘7’ AND ‘4’
Scan ENTER/EXIT PROGRAMMING MODE
TM
QuickScan
Lite QW2100
Set Length 2
Set Length 2
This feature specifies one of the bar code lengths for a given symbology. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length
Mode. Length includes the bar code’s data characters only.
Reference the Symbologies section to view the selectable range (number of characters) for the
symbology being set.. A setting of 00 specifies to ignore this length (only one fixed length).
Follow these instructions to set this feature:
1. Determine the desired character length. Pad the number with leading zeroes to yield two
digits. For example: 0 = 00, 5 = 05, 20 = 20, etc.
2. Scan the ENTER/EXIT PROGRAMMING MODE bar code to enter Programming
Mode.
3. Scan the “Select Length 2 Setting” for the symbology being set.
4. Scan the appropriate two digits from the keypad in Appendix E, Keypad, that represent
the length setting which was determined in the steps above. You will hear a two-beep indication after the last character.
If you make a mistake before the last character, scan the CANCEL bar
code to abort and not save the entry string. You can then start again at
the beginning.
NOTE
5. Scan the ENTER/EXIT PROGRAMMING MODE bar code to exit Programming
Mode.
This completes the procedure. See Table 20 for some examples of how to set this feature.
Table 20. Length 2 Setting Examples
STEP
ACTION
1
Desired Setting
EXAMPLES
00 (ignore second length)
07 Characters
52 Characters
2
Scan ENTER/EXIT PROGRAMMING MODE
3
Scan SELECT LENGTH 2 SETTING
4
Scan Two Characters From
Appendix E, Keypad
5
Product Reference Guide
‘0’ and ‘0’
‘0’ and ‘7’
‘5’ and ‘2’
74 Characters
‘7’ and ‘4’
Scan ENTER/EXIT PROGRAMMING MODE
269
References
NOTES
270
TM
QuickScan
Lite QW2100
Appendix A
Technical Specifications
Table 1 contains Physical and Performance Characteristics, User Environment and Regulatory information. Table 2 provides Standard Cable Pinouts.
Table 1. Technical Specifications
Item
Description
Physical Characteristics
2.8 in. H x 6.7 in. L x 2.6 in. W
Dimensions
(7.1 cm H x 17.1 cm L x 6.6 cm W)
Weight (without cable)
Approximately 4.2 oz. (119 g)
Color
Black or White
Electrical Characteristics
Voltage & Current
5.0 VDC +/-10%
Max Operating Current @ 5V < 260mA
Typical Operating (Scanning) Current @ 5V < 180mA
Idle Operating Current @ 5V < 80mA
Sleep/Suspend @ 5V < 2.5mA
Performance Characteristics
Light Source
617nm LEDs
Roll (Tilt) Tolerance
± 45° from normal
Pitch Tolerance
± 65°
Skew (Yaw) Tolerance
± 70°
Scan Angle
56° ± 2°
Typical Depth of Field
5.0 mil
7.5 mil
10 mil (80% UPC)
13 mil (100% UPC)
20 mil
Minimum Element Width
4 mil
Print Contrast Minimum
15% minimum reflectance
Product Reference Guide
1.5 - 15.0 cm
0 - 24.0 cm
0 - 38.0 cm
0 - 45.0 cm
* to 65.0 cm
271
Item
Decode Capability
Description
UPC/EAN/JAN, P2 /P5 GS1-128 add-ons; Code 39; Code 39 Full
ASCII; Code 32 (Italian Pharmacode); Code 128; ISBT 128; I 2 of
5; Standard 2 of 5; Code 11; Codabar; GS1-128; Code 93; MSI;
GS1 DataBar Omnidirectional, GS1 DataBar Limited, GS1 DataBar
Expanded; EAN 13 ISBN; Datalogic 2 of 5; Follet 2/5; Code 4, code
5.
QW2120: USB Com Std., USB Keyboard, USB Alternate Keyboard, USB-OEM.
Interfaces Supported
QW2170: RS-232 Std., RS-232 Wincor-Nixdorf, RS-232 OPOS,
Keyboard Wedge (AT with or w/o Alternate Key, IBM AT PS2 with
or w/o Alternate Key, PC-XT.
User Environment
Operating Temperature
32° to 122° F (0° to 50° C)
Storage Temperature
-40° to 158° F (-40° to 70° C)
Humidity
5% to 95% relative humidity, non-condensing
Drop Specifications
Withstands multiple 5 ft./1.524 m drops to concrete.
Ambient Light Immunity
Immune to direct exposure of normal office and factory lighting conditions, as well as direct exposure to sunlight.
Contaminants
Spray/rain
Dust/particulates
IEC 529-IPX2
IEC 529-IP4X
Beeper Volume
User-selectable: three levels
Beeper Tone (frequency)
User-selectable: three tones
Electrostatic Discharge
Conforms to ±16 kV air/direct discharge and ±8 kV of contact discharge.
Regulatory
Electrical Safety
EN60950/IEC60950
EMI/RFI
FCC Part 15 Class B, ICES-003 Class B, European Union EMC
Directive, Australia Class B, Japan VCCI/MITI
272
QuickScanTM Lite QW2100
Standard Cable Pinouts
Standard Cable Pinouts
Figure 10 and Table 2 provide standard pinout information for the reader’s cable.
Figure 10. Standard Cable Pinouts
Bottom of Imager
Cable
Cable Strain Relief
Interface Cable Port
Pin 1
Pin 10
To Host
Cable Clip (Latch)
The signal descriptions in Table 2 apply to the connector on the reader and are for reference only.
Table 2. Standard Cable Pinouts — Reader Side
Pin
RS-232
USB
Keyboard Wedge
1
RTS (out)
2
D+
CLKIN (KBD side)
3
D-
DATAIN (KBD side)
GND
GND
VCC
VCC
4
GND
5
RX
6
TX
7
VCC
8
CLKOUT (PC side)
9
DATAOUT (PC
side)
10
Product Reference Guide
CTS (in)
273
NOTES
274
QuickScanTM Lite QW2100
Appendix B
Standard Defaults
The most common configuration settings are listed in the “Default” column of Table 3.
The settings in this table are as applied to a standard RS-232 interface. See Table 4 for a
listing of default exceptions to this list as appled to other interface types. Page references
are also provided for feature descriptions and programming bar codes for each parameter.
A column has also been provided for recording of your preferred default settings for these
same configurable features.
Table 3. Standard Defaults
Parameter
Default
Your Setting
Page Number
General Features
Host Commands — Obey/Ignore
Obey
15
Disable
16
0.4 Second
17
Label Gone Timeout
160 ms
19
Power Save Mode
Enabled
20
Sleep Mode Timeout
Disabled
21
Power On Alert
4 Beeps
22
After Decode
23
Mono
24
Medium
25
80 ms
25
Illumination Off
during beep
27
Good Read Beep Volume
High
28
Good Read LED Duration
LED on until
next trigger pull
29
Trigger Single
30
0.5 Seconds
31
5 Seconds
33
Disable
33
USB Suspend Mode
Double Read Timeout
Good Read: When to Indicate
Good Read Beep Type
Good Read Beep Frequency
Good Read Beep Length
Illumination Control
Scan Mode
Stand Mode Triggered Timeout
Scanning Active Time
Stand Mode Flash
Product Reference Guide
275
Parameter
Default
Your Setting
Page Number
Flash On Time
1 Second
34
Flash Off Time
600 ms
34
Stand Mode Sensitivity
Medium
35
Green Spot Duration
300 ms
36
9600
37
Data Bits
8 Data Bits
39
Stop Bits
1 Stop Bit
39
None
40
Disable
41
Intercharacter Delay
No Delay
44
Beep On ASCII BEL
Disable
45
Beep On Not on File
Enable
45
ACK Character
‘ACK’
47
NAK Character
‘NAK’
47
600 ms
48
3 Retries
49
Ignore Errors
Detected
50
Enable
51
Disable Character
‘D’
51
Enable Character
‘E’
52
Country Mode
U.S. Keyboard
54
Caps Lock State
Caps Lock OFF
57
Numlock Key
Unchanged
58
Standard Keys
58
Keyboard Send Control Characters
Disable
59
Wedge Quiet Interval
100ms
60
Intercharacter Delay
No Delay
61
100 ms
62
1 ms
63
RS-232
Baud Rate
Parity
Handshaking Control
RS-232/USB-COM
ACK NAK Timeout Value
ACK NAK Retry Count
ACK NAK Error Handling
Indicate Transmission Failure
Keyboard Wedge
Numlock
Keyboard Numeric Keypad
Intercode Delay
USB Keyboard Speed
276
QuickScanTM Lite QW2100
Parameter
Default
Your Setting
Page Number
USB-OEM
USB-OEM Device Usage
Handheld Scanner
66
Ignore
66
No Global Prefix
Global Suffix =
0x0D (CR)
68
Global AIM ID
Disable
69
GS1-128 AIM ID
Enable
69
Label ID Control
Disable
71
No Characters
80
Disable
81
No Char Conversion
82
Enable only UPC/
EAN
84
UPC-A Enable/Disable
Enable
85
UPC-A Check Character Transmission
Enable
85
Don’t Expand
86
Transmit
86
2
87
Enable
88
Send
88
Expand UPC-E to EAN-13
Don’t Expand
89
Expand UPC-E to UPC-A
Don’t Expand
89
Transmit
90
2
90
Enable
91
Send
91
Transmit
92
USB-OEM Interface Options
Data Editing
Global Prefix/Suffix
Set Global Mid Label ID Character(s)
Case Conversion
Character Conversion
Symbologies
Coupon Control
UPC-A
Expand UPC-A to EAN-13
UPC-A Number System Character Transmission
In-Store Minimum Reads
UPC-E
UPC-E Enable/Disable
UPC-E Check Character Transmission
UPC-E Number System Character Transmission
UPC-E Minimum Reads
EAN 13
EAN 13 Enable/Disable
EAN 13 Check Character Transmission
EAN-13 Flag 1 Character
Product Reference Guide
277
Parameter
Default
EAN-13 ISBN Conversion
Disable
92
ISSN Enable/Disable
Disable
93
1
93
Enable
94
Send
94
Expand EAN 8 to EAN 13
Disable
95
EAN 8 Both Guards Substitution
Disable
95
EAN 8 Guard Insertion
Disable
96
EAN 8 Guard Substitution
Disable
96
EAN 8 Minimum Segment Length Block
8
97
EAN 8 Minimum Reads
1
99
EAN 8 Stitch Exact Label Halves
Disable
100
EAN 8 Stitch Unlike Label Halves
Disable
100
EAN Two Label Enable/Disable
Disable
101
EAN Two Label Combined Transmission
Disable
101
EAN Two Label Minimum Reads
1 Read
102
2
103
UPC/EAN Correlation
Disable
104
UPC/EAN Price Weight Check
Disable
105
UPC-A Minimum Reads
1 Read
106
UPC/EAN Guard Insertion
Disable
107
UPC/EAN Stitch Exact Label Halves
Disable
107
UPC/EAN Stitch Unlike Label Halves
Disable
108
UPC/EAN Minimum Segment Length
5
109
Disable P2, P5 and
P8
111
70 ms
113
P2 Add-Ons Minimum Reads
2
115
P5 Add-Ons Minimum Reads
1
116
EAN 13 Minimum Reads
Your Setting
Page Number
EAN 8
EAN 8 Enable/Disable
EAN 8 Check Character Transmission
EAN Two Label
UPC/EAN Global Settings
UPC/EAN Decoding Level
Add-Ons
Optional Add-ons
Optional Add-On Timer
278
QuickScanTM Lite QW2100
Parameter
GS1-128 Add-Ons Minimum Reads
Default
Your Setting
Page Number
1
117
GS1 DataBar Omnidirectional Enable/
Disable
Disable
118
GS1 DataBar Omnidirectional GS1-128
Emulation
Disable
118
GS1 DataBar Omnidirectional Minimum
Reads
1
119
GS1 DataBar Expanded Enable/Disable
Disable
120
GS1 DataBar Expanded GS1-128 Emulation
Disable
120
GS1 DataBar Expanded Minimum Reads
1
121
Variable
122
GS1 DataBar Expanded Set Length 1
1
123
GS1 DataBar Expanded Set Length 2
74
124
GS1 DataBar Limited Enable/Disable
Disable
125
GS1 DataBar Limited GS1-128 Emulation
Disable
125
1
126
Enable
127
Don’t Calculate
128
Code 39 Check Character Transmission
Send
129
Code 39 Start/Stop Character Transmission
Don’t Transmit
129
Disable
130
Auto
131
Code 39 Minimum Reads
2
132
Code 39 Decoding Level
3
133
Code 39 Length Control
Variable
134
Code 39 Set Length 1
2
135
Code 39 Set Length 2
50
136
Code 39 Interdigit Ratio
4
137
Disable
139
GS1 DataBar Omnidirectional
GS1 DataBar Expanded
GS1 DataBar Expanded Length Control
GS1 DataBar Limited
GS1 DataBar Limited Minimum Reads
Code 39
Code 39 Enable/Disable
Code 39 Check Character Calculation
Code 39 Full ASCII
Code 39 Quiet Zones
Code 39 Character Correlation
Product Reference Guide
279
Parameter
Code 39 Stitching
Default
Your Setting
Page Number
Enable
139
Disable
140
Code 32 Check Character Transmission
Don’t Send
141
Code 32 Start/Stop Character Transmission
Don’t Transmit
141
Disable
142
Enable
142
Don’t Expand
143
Don’t Send
143
Auto
145
Code 128 Minimum Reads
1
146
Code 128 Decoding Level
3
147
Code 128 Length Control
Variable
148
Code 128 Set Length 1
1
149
Code 128 Set Length 2
80
150
Code 128 Character Correlation
Disable
151
Code 128 Stitching
Enable
151
Transmit in Code
128 Data Format
152
I 2 of 5 Enable/Disable
Disable
153
I 2 of 5 Check Character Calculation
Disable
154
Send
155
I 2 of 5 Minimum Reads
2
165
I 2 of 5 Decoding Level
3
157
I 2 of 5 Length Control
Variable
158
I 2 of 5 Set Length 1
12
159
I 2 of 5 Set Length 2
100
160
I 2 of 5 Character Correlation
Disable
161
I 2 of 5 Stitching
Disable
162
Code 32
Code 32 Enable/Disable
Code 39 CIP
Code 39 CIP Enable/Disable
Code 128
Code 128 Enable/Disable
Expand Code 128 to Code 39
Code 128 Check Character Transmission
Code 128 Quiet Zones
GS1-128
GS1-128 Enable
Interleaved 2 of 5
I 2 of 5 Check Character Transmission
280
QuickScanTM Lite QW2100
Parameter
Default
Your Setting
Page Number
Interleaved 2 of 5 CIP
Interleaved 2 of 5 CIP HR Enable/Disable
Disable
162
Datalogic 2 of 5 Enable/Disable
Enable
163
Datalogic 2 of 5 Check Character Calculation
Disable
164
Datalogic 2 of 5 Check Character Transmission
Don’t Send
164
2
165
Variable
166
Datalogic 2 of 5 Set Length 1
12
167
Datalogic 2 of 5 Set Length 2
100
168
4
169
Datalogic 2 of 5 Character Correlation
Disable
171
Datalogic 2 of 5 Stitching
Disable
171
Disable
172
Don’t Calculate
172
Codabar Check Character Transmission
Send
173
Codabar Start/Stop Character Transmission
Transmit
173
abcd/abcd
174
Don’t Require
Match
175
Auto
176
Codabar Minimum Reads
2
177
Codabar Decoding Level
3
178
Codabar Length Control
Variable
179
Codabar Set Length 1
3
180
Codabar Set Length 2
50
181
Codabar Interdigit Ratio
4
182
Codabar Character Correlation
Disable
184
Codabar Stitching
Disable
184
Disable
185
Datalogic 2 of 5
Datalogic 2 of 5 Minimum Reads
Datalogic 2 of 5 Length Control
Datalogic 2 of 5 Interdigit Maximum Ratio
Codabar
Codabar Enable/Disable
Codabar Check Character Calculation
Codabar Start/Stop Character Set
Codabar Start/Stop Character Match
Codabar Quiet Zones
ABC Codabar
ABC Codabar Enable/Disable
Product Reference Guide
281
Parameter
ABC Codabar Concatenation Mode
Default
Your Setting
Page Number
Static
185
ABC Codabar Dynamic Concatenation
Timeout
200mS
186
ABC Codabar Force Concatenation
Disable
187
Disable
187
Check C and K
188
Send
188
2
189
Variable
190
Code 11 Set Length 1
4
191
Code 11 Set Length 2
50
192
Code 11 Interdigit Ratio
4
193
Code 11 Decoding Level
3
195
Code 11 Character Correlation
Disable
196
Code 11 Stitching
Disable
196
Standard 2 of 5 Enable/Disable
Disable
197
Standard 2 of 5 Check Character Calculation
Disable
197
Send
198
Standard 2 of 5 Minimum Reads
2
198
Standard 2 of 5 Decoding Level
3
199
Standard 2 of 5 Length Control
Variable
199
Standard 2 of 5 Set Length 1
8
200
Standard 2 of 5 Set Length 2
50
201
Standard 2 of 5 Character Correlation
Disable
202
Standard 2 of 5 Stitching
Disable
202
Industrial 2 of 5 Enable/Disable
Disable
203
Industrial 2 of 5 Check Character Calculation
Disable
203
Industrial 2 of 5 Check Character Transmission
Enable
204
Code 11
Code 11 Enable/Disable
Code 11 Check Character Calculation
Code 11 Check Character Transmission
Code 11 Minimum Reads
Code 11 Length Control
Standard 2 of 5
Standard 2 of 5 Check Character Transmission
Industrial 2 of 5
282
QuickScanTM Lite QW2100
Parameter
Industrial 2 of 5 Length Control
Default
Your Setting
Page Number
Variable
204
Industrial 2 of 5 Set Length 1
1 Character
205
Industrial 2 of 5 Set Length 2
50 Characters
206
Industrial 2 of 5 Minimum Reads
1 Read
207
Industrial 2 of 5 Stitching
Disable
208
Industrial 2 of 5 Character Correlation
Disable
208
IATA Enable/Disable
Disable
209
IATA Check Character Transmission
Enable
209
Disable
210
ISBT 128 Concatenation Mode
Static
210
ISBT 128 Dynamic Concatenation Timeout
200ms
211
ISBT 128 Force Concatenation
Disable
212
ISBT 128 Advanced Concatenation
Options
Disable
212
Disable
213
Enable Mod10
213
MSI Check Character Transmission
Enable
214
MSI Length Control
Variable
214
MSI Set Length 1
1 Character
215
MSI Set Length 2
50 Characters
216
MSI Minimum Reads
4 Reads
217
MSI Decoding Level
Level 3
218
Code 93 Enable/Disable
Disable
219
Code 93 Check Character Calculation
Disable
219
Code 93 Check Character Transmission
Enable
220
Code 93 Length Control
Variable
220
Code 93 Set Length 1
1 Character
221
Code 93 Set Length 2
50 Characters
222
1 Read
223
IATA
ISBT 128
ISBT 128 Concatenation
MSI
MSI Enable/Disable
MSI Check Character Calculation
Code 93
Code 93 Minimum Reads
Product Reference Guide
283
Parameter
Default
Code 93 Decoding Level
Your Setting
Page Number
Level 3
224
Auto
225
Code 93 Stitching
Enable
226
Code 93 Character Correlation
Enable
226
Codablock F Enable/Disable
Disable
227
Codablock F EAN Enable/Disable
Disable
227
Enable Check C
228
Variable
228
Codablock F Set Length 1
3 Characters
229
Codablock F Set Length 2
100 Characters
230
Code 4 Enable/Disable
Disable
231
Code 4 Check Character Transmission
Enable
231
Code 4 Hex to Decimal Conversion
Enable
232
Code 5 Enable/Disable
Disable
232
Code 5 Check Character Transmission
Enable
233
Code 5 Hex to Decimal Conversion
Enable
233
Code 4 and 5 Decoding Level
3
234
Code 4 and Code 5 Minimum Reads
1
235
Disable
236
Disable
236
Don’t Calculate
237
BC412 Minimum Reads
2 Reads
238
BC412 Decoding Level
3
239
BC412 Length Control
Variable Length
240
BC412 Set Length 1
1 Character
241
BC412 Set Length 2
50 Characters
242
Code 93 Quiet Zones
Codablock F
Codablock F AIM Check
Codablock F Length Control
Code 4
Code 5
Code 4 and Code 5 Common Configuration Items
Follett 2 of 5
Follett 2 of 5 Enable/Disable
BC412
BC412 Enable/Disable
BC412 Check Character Calculation
284
QuickScanTM Lite QW2100
Default Exceptions
Default Exceptions
Table 3 lists standard default settings as applied to a standard RS-232 interface. Table 4
provides a listing of default exceptions to that list as applied to the other interface types.
Table 4. Default Exceptions by Interface Type
Parameter
Default Excption
Interfaces: USB-OEM
Global Suffix
Double Read Timeout
No Global Suffix
500 msec
Interfaces: All Keyboard Wedge, USB Keyboard
No unique settings
Interface: RS232-WN
Expand UPC-A to EAN-13
Enable
UPC-E Check Character Transmission
Disable
Parity
Odd Parity
Handshaking Control
RTS/CTS
Transmission Label ID Code
GS1-128 AIM ID
Prefix
Disable
UPCE Label ID Character(s)
C
EAN 8 Label ID Character(s)
B
EAN 13 Label ID Character(s)
A
Code ISBN Label ID Character(s)
A
Code 39 Label ID Character(s)
M
Interelaved 2of5 Label ID Character(s)
I
Code Standard 2/5 Label ID Character(s)
H
Codabar Label ID Character(s)
N
Code 128 Label ID Character(s)
K
GS1-128 Label ID Character(s)
P
Datalogic 2 of 5 Label ID Character(s)
H
ISBT 128 Label ID Character(s)
K
UPCE P2 Label ID Character(s)
C
UPCE/P5 Label ID Character(s)
C
UPCE/GS1-128 Label ID Character(s)
C
EAN8/P2 Label ID Character(s)
B
EAN8/P5 Label ID Character(s)
B
EAN8/GS1-128 Label ID Character(s)
B
Product Reference Guide
285
Parameter
Default Excption
EAN13/P2 Label ID Character(s)
A
EAN13/P5 Label ID Character(s)
A
EAN13/GS1-128 Label ID Character(s)
A
GS1 DataBar 14 (Omnidirectional) Label ID Character(s)
E
GS1 DataBar Expanded Label ID Character(s)
E
GS1 DataBar Limited Label ID Character(s)
E
Character Conversion
CR to `
Interface: RS232-OPOS
Baud Rate
Transmission Label ID Code
GS1-128 AIM ID
286
115200 Baud
Prefix
Disable
UPCA Label ID Character(s)
C
UPCE Label ID Character(s)
D
EAN 8 Label ID Character(s)
A
EAN 13 Label ID Character(s)
B
Code ISBN Label ID Character(s)
@
Code 39 Label ID Character(s)
V
Code 32 Label ID Character(s)
X
Interelaved 2of5 Label ID Character(s)
N
Code Standard 2/5 Label ID Character(s)
P
Codabar Label ID Character(s)
R
Code 11 Label ID Character(s)
b
Code 128 Label ID Character(s)
T
GS1-128 Label ID Character(s)
k
UPCA/P2 Label ID Character(s)
F
UPCA/P5 Label ID Character(s)
G
UPCA/GS1-128 Label ID Character(s)
Q
UPCE P2 Label ID Character(s)
H
UPCE/P5 Label ID Character(s)
I
EAN8/P2 Label ID Character(s)
J
EAN8/P5 Label ID Character(s)
K
EAN8/GS1-128 Label ID Character(s)
*
EAN13/P2 Label ID Character(s)
L
QuickScanTM Lite QW2100
Default Exceptions
Parameter
Default Excption
EAN13/P5 Label ID Character(s)
M
EAN13/GS1-128 Label ID Character(s)
#
GS1 DataBar 14 (Omnidirectional) Label ID Character(s)
u
GS1 DataBar Expanded Label ID Character(s)
t
GS1 DataBar Limited Label ID Character(s)
v
Product Reference Guide
287
NOTES
288
QuickScanTM Lite QW2100
Appendix C
LED and Beeper Indications
The reader’s beeper sounds and its LED illuminates to indicate various functions or errors on the reader. An optional “Green Spot” also performs useful functions. The tables
below list these indications. One exception to the behaviors listed in the tables is that the
reader’s functions are programmable, and may or may not be turned on. For example,
certain indications, such as the power-up beep can be disabled using programming bar
code labels.
Product Reference Guide
289
LED and Beeper Indications
INDICATION
DESCRIPTION
LED
BEEPER
Reader beeps four times at highest frequency and volume upon
power-up.
Power-up Beep
The reader is in the process of
powering-up.
Good Read Beep
A label has been successfully
scanned by the reader.
ROM Failure
There is an error in the reader's
software/programming
Flashes
Reader sounds one error beep
at highest volume.
Limited Scanning
Label Read
Indicates that a host connection
is not established when the USB
interface is enabled.
N/A
Reader 'chirps' six times at the
highest frequency and current
volume.
Reader Active
Mode
The reader is active and ready to
scan.
The LED is lit steadilya
Reader
Disabled
The reader has been disabled by
the host.
Green Spot is on
continuously
While in Stand Mode or Trigger
Object Sense mode the green
spot shall be on while in stand
watch state.
N/A
N/A
Green Spota
flashes momentarily
Upon successful read of a label,
the software shall turn the green
spot on for the time specified by
the configured value.
N/A
N/A
LED behavior for this indication is configurable via
the feature “Good Read:
When to Indicate”
The LED blinks continuously
The reader will beep once at current frequency, volume, mono/bitonal setting and duration upon a
successful label scan.
N/A
N/A
Programming Mode - The following indications ONLY occur when the reader is in Programming Mode.
Label Programming Mode Entry
A valid programming label has
been scanned.
Label Programming Mode
Rejection of Label
A label has been rejected.
N/A
Label Programming Mode
Acceptance of
Partial Label
In cases where multiple labels
must be scanned to program one
feature, this indication acknowledges each portion as it is successfully scanned.
N/A
Reader sounds one short beep
at highest frequency & current
volume.
Label Programming Mode
Acceptance of
Programming
Configuration option(s) have
been successfully programmed
via labels and the reader has
exited Programming Mode.
N/A
Reader sounds one high frequency beep and 4 low frequency beeps followed by reset
beeps.
Label Programming Mode Cancel Item Entry
Cancel label has been scanned.
N/A
Reader sounds two times at low
frequency and current volume.
a.
290
LED blinks continuously
Reader sounds four low frequency beeps.
Reader sounds three times at
lowest frequency & current volume.
Except when in sleep mode or when a Good Read LED Duration other than 00 is selected
QuickScanTM Lite QW2100
Error Codes
Error Codes
Upon startup, if the reader sounds a long tone, this means the reader has not passed its
automatic Selftest and has entered FRU1 isolation mode. If the reader is reset, the sequence will be repeated. The following table describes the LED flashes/beep codes associated with an error found.
NUMBER OF
LED
FLASHES/
BEEPS
ERROR
1
Configuration
2
Interface PCB
4
Reader Module
5
[Reserved]
6
Digital PCB
14
CPLD/Code Mismatch
CORRECTIVE ACTION
Contact Helpdesk for assistance
1. Field Replaceable Unit (FRU)
Product Reference Guide
291
NOTES
292
QuickScanTM Lite QW2100
Appendix D
Sample Bar Codes
The sample bar codes in this appendix are typical representations for their symbology
types.
UPC-A
0
12345 67890
5
EAN-13
3 4 5 67 8 9 0 1 2 3 4 0
Code 39
123ABC
Code 128
12345678901234567890123456789012345678901234
Interleaved 2 of 5
12345678901231
Product Reference Guide
293
Sample Bar Codes — continued
Code 32
Codabar
Code 93
Code 11
294
QuickScanTM Lite QW2100
GS1 DataBar (RSS)
GS1 DataBar (RSS)
GS1 DataBar variants must be enabled to read the bar codes below
(see GS1 DataBar (RSS) on page 295).
NOTE
10293847560192837465019283746029478450366523
(GS1 DataBar Expanded Stacked)
1234890hjio9900mnb
(GS1 DataBar Expanded)
08672345650916
(GS1 DataBar Limited)
GS1 DataBar-14
55432198673467
(GS1 DataBar Omnidirectional Truncated)
90876523412674
(GS1 DataBar Omnidirectional Stacked)
78123465709811
(GS1 DataBar Omnidirectional Stacked)
Product Reference Guide
295
NOTES
296
QuickScanTM Lite QW2100
Appendix E
Keypad
Use the bar codes in this appendix to enter numbers as you would select digits/characters
from a keypad.
0
1
2
3
4
5
Product Reference Guide
297
6
7
8
9
A
B
C
298
QuickScanTM Lite QW2100
D
E
F
Product Reference Guide
299
NOTES
300
QuickScanTM Lite QW2100
Appendix F
Scancode Tables
Control Character Emulation
Control character emulation selects from different scancode tables as listed in this appendix. Each of the
control character sets below are detailed by interface type in the tables. These apply to Wedge and USB
Keyboard platforms.
Control Character 00 — Characters from 00 to 0x1F are sent as control character Ctrl+Keys, special keys
are located from 0x80 to 0xA1.
Control Character 01 — Characters from 00 to 0x1F are sent as control character Ctrl+Capital Key, special keys are located from 0x80 to 0xA1.
Control Character 02 — Special keys are located from 00 to 0x1F and characters from 0x80 to 0xFE are
intended as an extended ASCII table (Microsoft Windows Codepage 1252 — see page 308).
Product Reference Guide
301
Interface Type PC AT PS/2 or USB-Keyboard
Table 1. Scancode Set When Control Character is 00 or 01
x0
x1
x2
x3
x4
x5
X6
x7
x8
x9
xA
xB
xC
xD
xE
xF
NULL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
C(S)+
@
C(S)+A
C(S)+B
C(S)+C
C+D
C(S)+E
C(S)+F
C(S)+
G
C(S)+
H
TAB
C(S)+J
C(S)+K
C(S)+L
Enter
C(S)+
N
C(S)+
O
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
C(S)+P
C(S)+
Q
C(S)+R
C(S)+S
C(S)+T
C(S)+
U
C(S)+V
C(S)+
W
C(S)+X
C(S)+Y
C(S)+Z
Esc
C(S)+\
C+]
C(S)+^
C(S)+_
2x
SP
!
"
#
$
%
&
'
(
)
*
+
,
-
.
/
3x
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
4x
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
5x
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
6x
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
7x
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
Del
8x
_
Sh
Sh
Ins
Ent
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
0x
1x
(keyp)
9x
F12
Home
End
Pg Up
Pg
Dwn
á
â
ß
à
Ar
Ar
Al
Al 
Cl
Cl 
Cr
Ax
Cr
_
‘
ƒ
„
…
†
‡
ˆ
‰
Š
‹
Ś
‹
Œ
_
Bx
°
±
²
³
´
μ
¶
·
¸
¹
º
»
¼
½
¾
¿
Cx
À
Á
Â
Ã
Ä
Å
Æ
Ç
È
É
Ê
Ë
Ì
Í
Î
Ï
Dx
Ð
_
Ò
Ó
Ô
Õ
Ö
×
Ø
Ù
Ú
Û
Ü
Ý
Þ
ß
Ex
à
á
â
ã
ä
å
æ
ç
è
é
ê
ë
ì
í
î
ï
Fx
ð
ñ
ò
ó
ô
õ
ö
÷
ø
ù
ú
û
ü
ý
þ
ÿ
Extended characters (sky blue) are sent via dedicated keys (when available in the selected country mode) or by an Alt Mode sequence.
Product Reference Guide
302
Interface Type PC AT PS/2 or USB-Keyboard — cont.
Table 2. Scancode Set When Control Character is 02
x0
x1
x2
x3
x4
x5
X6
x7
x8
x9
xA
xB
xC
xD
xE
xF
0x
Ar
Ar
Al
Al 
Cl 
Cl 
Cr 
Cr 
BS
Tab
à
S+ Tab
Enter
Keypd
Enter
Ins
Pg Up
1x
Pg
Dwn
Home
ß
â
á
F6
F1
F2
F3
F4
F5
ESC
F7
F8
F9
F10
2x
Space
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
3x
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
4x
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
5x
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
6x
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
7x
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
Del
8x
_
_
‘
ƒ
„
…
†
‡
ˆ
‰
Š
‹
Ś
‹
Œ
_
9x
_
‘
’
“
”
•
–
—
˜
™
š
›
œ
_
_
Ÿ
Ax
NBSP
¡
¢
£
¤
¥
¦
§
¨
©
ª
«
¬
-
®
¯
Bx
°
±
²
³
´
μ
¶
·
¸
¹
º
»
¼
½
¾
¿
Cx
À
Á
Â
Ã
Ä
Å
Æ
Ç
È
É
Ê
Ë
Ì
Í
Î
Ï
Dx
Ð
_
Ò
Ó
Ô
Õ
Ö
×
Ø
Ù
Ú
Û
Ü
Ý
Þ
ß
Ex
à
á
â
ã
ä
å
æ
ç
è
é
ê
ë
ì
í
î
ï
Fx
ð
ñ
ò
ó
ô
õ
ö
÷
ø
ù
ú
û
ü
ý
þ
ÿ
Product Reference Guide
303
Interface type PC AT PS/2 Alt Mode or USB-Keyboard Alt Mode
Table 3. Scancode Set When Control Character is 00 or 01
x0
x1
x2
x3
x4
x5
X6
x7
x8
x9
xA
xB
xC
xD
xE
Xf
Alt+00
0
Alt+00
1
Alt+00
2
Alt+00
3
Alt+00
4
Alt+00
5
Alt+00
6
Alt+00
7
Alt+00
8
HT
Alt+01
0
Alt+01
1
Alt+01
2
CR
Alt+01
4
Alt+01
5
Alt+01
6
Alt+01
7
Alt+01
8
Alt+01
9
Alt+02
0
Alt+02
1
Alt+02
2
Alt+02
3
Alt+02
4
Alt+02
5
Alt+02
6
ESC
Alt+02
8
Alt+02
9
Alt+03
0
Alt+03
1
2x
A+032
A+033
A+034
A+035
A+036
A+037
A+038
A+039
A+040
A+041
A+042
A+043
A+044
A+045
A+046
A+047
3x
A+048
A+049
A+050
A+051
A+052
A+053
A+054
A+055
A+056
A+057
A+058
A+059
A+060
A+061
A+062
A+063
4x
A+064
A+065
A+066
A+067
A+068
A+069
A+070
A+071
A+072
A+073
A+074
A+075
A+076
A+077
A+078
A+079
5x
A+080
A+081
A+082
A+083
A+084
A+085
A+086
A+087
A+088
A+089
A+090
A+091
A+092
A+093
A+094
A+095
6x
A+096
A+097
A+098
A+099
A+100
A+101
A+102
A+103
A+104
A+105
A+106
A+107
A+108
A+109
A+110
A+111
7x
A+112
A+113
A+114
A+115
A+116
A+117
A+118
A+119
A+120
A+121
A+122
A+123
A+124
A+125
A+126
A+127
8x
_
Sh
Sh?
Ins
Ent
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
0x
1x
TAB
Esc
Enter
(keyp)
9x
F12
Home
End
Pg Up
Pg
Dwn
á
â
ß
à
Ar
Ar
Al
Al 
Cl 
Cl 
Cr 
Ax
Cr
A+016
1
A+016
2
A+016
3
A+016
4
A+016
5
A+016
6
A+016
7
A+016
8
A+016
9
A+017
0
A+017
1
A+017
2
A+017
3
A+017
4
A+017
5
Bx
A+017
6
A+017
7
A+017
8
A+017
9
A+018
0
A+018
1
A+018
2
A+018
3
A+018
4
A+018
5
A+018
6
A+018
7
A+018
8
A+018
9
A+019
0
A+019
1
Cx
A+019
2
A+019
3
A+019
4
A+019
5
A+019
6
A+019
7
A+019
8
A+019
9
A+020
0
A+020
1
A+020
2
A+020
3
A+020
4
A+020
5
A+020
6
A+020
7
Dx
A+020
8
A+020
9
A+021
0
A+021
1
A+021
2
A+021
3
A+021
4
A+021
5
A+021
6
A+021
7
A+021
8
A+021
9
A+022
0
A+022
1
A+022
2
A+022
3
Ex
A+022
4
A+022
5
A+022
6
A+022
7
A+022
8
A+022
9
A+023
0
A+023
1
A+023
2
A+023
3
A+023
4
A+023
5
A+023
6
A+023
7
A+023
8
A+023
9
Fx
A+024
0
A+024
1
A+024
2
A+024
3
A+024
4
A+024
5
A+024
6
A+024
7
A+024
8
A+024
9
A+025
0
A+025
1
A+052
A+025
3
A+025
4
A+025
5
Product Reference Guide
304
Interface type PC AT PS/2 Alt Mode or USB-Keyboard Alt Mode — cont.
Table 4. Scancode Set When Control Character is 02
x0
x1
x2
x3
x4
x5
X6
x7
x8
x9
xA
xB
xC
xD
xE
xF
0x
Ar
Ar
Al
Al
Cl
Cl
Cr
Cr
BS
Tab
à
S+ Tab
Enter
Keypd
Enter
Ins
Pg Up
1x
Pg
Dwn
Home
ß
â
á
F6
F1
F2
F3
F4
F5
ESC
F7
F8
F9
F10
2x
A+032
A+033
A+034
A+035
A+036
A+037
A+038
A+039
A+040
A+041
A+042
A+043
A+044
A+045
A+046
A+047
3x
A+048
A+049
A+050
A+051
A+052
A+053
A+054
A+055
A+056
A+057
A+058
A+059
A+060
A+061
A+062
A+063
4x
A+064
A+065
A+066
A+067
A+068
A+069
A+070
A+071
A+072
A+073
A+074
A+075
A+076
A+077
A+078
A+079
5x
A+080
A+081
A+082
A+083
A+084
A+085
A+086
A+087
A+088
A+089
A+090
A+091
A+092
A+093
A+094
A+095
6x
A+096
A+097
A+098
A+099
A+100
A+101
A+102
A+103
A+104
A+105
A+106
A+107
A+108
A+109
A+110
A+111
7x
A+112
A+113
A+114
A+115
A+116
A+117
A+118
A+119
A+120
A+121
A+122
A+123
A+124
A+125
A+126
A+127
8x
A+012
8
A+012
9
A+013
0
A+013
1
A+013
2
A+013
3
A+013
4
A+013
5
A+013
6
A+013
7
A+013
8
A+013
9
A+014
0
A+014
1
A+014
2
A+014
3
9x
A+014
4
A+014
5
A+014
6
A+014
7
A+014
8
A+014
9
A+015
0
A+015
1
A+015
2
A+015
3
A+015
4
A+015
5
A+015
6
A+015
7
A+015
8
A+015
9
Ax
A+016
0
A+016
1
A+016
2
A+016
3
A+016
4
A+016
5
A+016
6
A+016
7
A+016
8
A+016
9
A+017
0
A+017
1
A+017
2
A+017
3
A+017
4
A+017
5
Bx
A+017
6
A+017
7
A+017
8
A+017
9
A+018
0
A+018
1
A+018
2
A+018
3
A+018
4
A+018
5
A+018
6
A+018
7
A+018
8
A+018
9
A+019
0
A+019
1
Cx
A+019
2
A+019
3
A+019
4
A+019
5
A+019
6
A+019
7
A+019
8
A+019
9
A+020
0
A+020
1
A+020
2
A+020
3
A+020
4
A+020
5
A+020
6
A+020
7
Dx
A+020
8
A+020
9
A+021
0
A+021
1
A+021
2
A+021
3
A+021
4
A+021
5
A+021
6
A+021
7
A+021
8
A+021
9
A+022
0
A+022
1
A+022
2
A+022
3
Ex
A+022
4
A+022
5
A+022
6
A+022
7
A+022
8
A+022
9
A+023
0
A+023
1
A+023
2
A+023
3
A+023
4
A+023
5
A+023
6
A+023
7
A+023
8
A+023
9
Fx
A+024
0
A+024
1
A+024
2
A+024
3
A+024
4
A+024
5
A+024
6
A+024
7
A+024
8
A+024
9
A+025
0
A+025
1
A+052
A+025
3
A+025
4
A+025
5
Product Reference Guide
305
Digital Interface
Table 5. Scancode Set When Control Character is 00 or 01
X0
x1
x2
x3
x4
x5
x6
x7
x8
x9
xA
xB
xC
xD
xE
xF
NULL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
C(S)+
@
C(S)+A
C(S)+B
C(S)+C
C+D
C(S)+E
C(S)+F
C(S)+
G
C(S)+
H
TAB
C(S)+J
C(S)+K
C(S)+L
Enter
C(S)+
N
C(S)+
O
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
C(S)+P
C(S)+
Q
C(S)+R
C(S)+S
C(S)+T
C(S)+
U
C(S)+V
C(S)+
W
C(S)+X
C(S)+Y
C(S)+Z
Esc
C(S)+\
C+]
C(S)+^
C(S)+_
2x
Space
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
3x
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
4x
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
5x
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
6x
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
7x
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
Del
Sh
Sh
Ins
Ent
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
á
â
ß
à
Cl
Cl
0x
1x
8x
(keyp)
9x
F12
F13
Product Reference Guide
F14
F15
F16
306
Digital Interface — cont.
Table 6. Scancode Set When Control Character is 02
X0
x1
x2
x3
0x
1x
x4
x5
Cl
Cl
x6
x7
x8
x9
xA
xB
xC
xD
xE
BS
Tab
à
S+ Tab
Enter
Keypd
Enter
Ins
xF
ß
â
á
F6
F1
F2
F3
F4
F5
ESC
F7
F8
F9
F10
2x
Space
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
3x
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
4x
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
5x
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
6x
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
7x
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
Del
Product Reference Guide
307
IBM XT
Table 7. Scancode Set When Control Character is 00 or 01
X0
x1
x2
x3
x4
x5
x6
x7
x8
x9
xA
xB
xC
xD
xE
xF
NULL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
C(S)+
@
C(S)+A
C(S)+B
C(S)+C
C+D
C(S)+E
C(S)+F
C(S)+
G
C(S)+
H
TAB
C(S)+J
C(S)+K
C(S)+L
Enter
C(S)+
N
C(S)+
O
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
C(S)+P
C(S)+
Q
C(S)+R
C(S)+S
C(S)+T
C(S)+
U
C(S)+V
C(S)+
W
C(S)+X
C(S)+Y
C(S)+Z
Esc
C(S)+\
C+]
C(S)+^
C(S)+_
2x
Space
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
3x
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
4x
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
5x
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
6x
‘
a
B
c
d
e
f
g
h
i
j
k
l
m
n
o
7x
p
q
R
s
t
u
v
w
x
y
z
{
|
}
Sh?
Sh?
Ins
Ent
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
á
â
ß
à
Ar
Ar
Al
Al
Cl
Cl
Cr
0x
1x
8x
Del
(keyp)
9x
F12
Ax
Cr
Home
Product Reference Guide
End
Pg Up
Pg
Dwn
308
IBM XT — cont.
Table 8. Scancode Set When Control Character is 02
X0
x1
x2
x3
x4
x5
x6
x7
x8
x9
xA
xB
xC
xD
xE
xF
0x
Ar
Ar
Al
Al
Cl
Cl
Cr
Cr
BS
Tab
à
S+ Tab
Enter
Keypd
Enter
Ins
Pg Up
1x
Pg
Dwn
Home
ß
â
á
F6
F1
F2
F3
F4
F5
ESC
F7
F8
F9
F10
2x
Space
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
3x
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
4x
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
5x
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
6x
‘
a
B
c
d
e
f
g
h
i
j
k
l
m
n
o
7x
p
q
R
s
t
u
v
w
x
y
z
{
|
}
Product Reference Guide
Del
309
Microsoft Windows Codepage 1252
Windows-1252 is a character encoding of the Latin alphabet, used by default in the legacy components of
Microsoft Windows in English and some other Western languages.
310
QuickScanTM Lite QW2100
Index
B
bar codes
RS-232
baud rate 63
RS-232 parameters
parity 231, 232, 234, 236
barcodes
cancel 297
numeric barcodes 297
RS-232 parameters
parity 57
Beeper
Pitch, Good Read 24, 25
Volume, Good Read 28
Beeper, Good Read 22
Pitch 24, 25
Volume 28
Good Read, Beeper – 22
Good Read, Beeper Pitch – 24, 25
Good Read, Beeper Volume – 28
Green Spot 289
H
Handheld Scanner 66
I
Indications 289
Interface Cable 6
Interface Type 9
Interfaces Supported 272
C
Cable Pinouts 273
Clear to Send 41
Conversion, case 81
Conversion, character 82, 266
CTS 41
D
Decode Capability 272
Defaults 275
Depth of Field 271
K
keyboard support 54
KEYBOARD WEDGE (KBW) interface selection
13
Keyboard Wedge Connection 7
L
Light Source 271
N
E
numbers lock key 58
Electrical Safety 272
EMI/RFI 272
Error Codes 291
Errors 291
P
G
Good Read, Beeper 22
Product Reference Guide
Performance Characteristics 271
Physical Characteristics 271
Pitch – Good Read, Beeper 24, 25
Pitch Tolerance 271
Prefix/Suffix 68, 260
311
Print Contrast Minimum 271
Product Specifications 271
Programming Barcodes 9
X
XON/XOFF 41
R
Read, Beeper – Good 22
Read, Beeper Pitch – Good 24, 25
Read, Beeper Volume – Good 28
Request to Send 41
Roll (Tilt) Tolerance 271
RS-232 interface selection 12
RS-232 Serial Connection 6
RTS 41
S
sample bar codes
code 128 293
code 39 293
interleaved 2 of 5 294
select digits/characters 297
Serial Output 273
Skew (Yaw) Tolerance 271
Standard Cable Pinouts 273
Suffix 68, 260
Symbologies 243
symbology types 293
T
Table Top Scanner 66
U
UPC 85
USB Connection 7
USB interface selection 12
User Environment 272
V
Volume – Good Read, Beeper 28
312
QuickScanTM Lite QW2100
ASCII Chart
ASCI
I
Char.
Hex
No.
ASCI
I
Char.
Hex
No.
ASCI
I
Char.
Hex
No.
ASCI
I
Char.
Hex
No.
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
SP
!
“
#
$
%
&
’
(
)
*
+
,
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
‘
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
DEL
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
www.datalogic.com
©2011-2014 Datalogic ADC, Inc. All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S.A. and the E.U.
Datalogic ADC, Inc.
959 Terry Street | Eugene |OR 97402 | USA
Telephone: (1) 541-683-5700 | Fax: (1) 541-345-7140
820036414 (Rev. C)
January 2014
Download PDF
Similar pages