spx-wkt2_installation manual_1_EN_11L

MODEL
SPX-WKT2
CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
SAFETY PRECAUTIONS
INSTALLATION WORK
NAMES AND FUNCTIONS OF REMOTE CONTROLLER
ADJUSTING DATE/TIME
LANGUAGE SETTING
SCREEN DISPLAY SETTING
THERMISTOR SELECTION
DISPLAY ROOM TEMPERATURE (SERVICE MENU)
CONTACT INFORMATION REGISTRATION (SERVICE MENU)
........................... 2
........................... 2
........................... 4
........................... 5
........................... 5
........................... 6
........................... 6
........................... 7
........................... 7
Русский Suomi Nederlands Svenska Ελληνικα Português Español Italiano Deutsch Français English
WIRED REMOTE CONTROLLER
INSTALLATION MANUAL
1. SAFETY PRECAUTIONS
Also see installation manual attached to the indoor unit.
• Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.
• Pay special attention to signs of “
Warning” and “
Caution”. The “Warning” section contains matters which, if not observed strictly,
may cause death or serious injury. The “Caution” section contains matters which may result in serious consequences if not observed properly.
Please observe all instructions strictly to ensure safety.
• Be sure that the unit operates in proper condition after installation. Explain to customer the proper operation and maintenance of the unit as
described in the user' s guide. Ask a customer to keep this installation manual together with the instruction manual.
WARNING
• Please request your sales agent or qualified technician to install your remote controller. Short circuit or fire may occur if you do the installation
work yourself.
• Do not pour water into the remote controller. This product is equipped with electrical parts. If poured, it will cause a serious electrical shock.
• Please observe the installation stated in the installation manual during the process of installation. Improper installation may cause electric
shock and fire.
• Please contact your agent for maintenance. Improper self maintenance may cause electric shock and fire.
• Please contact your agent if you need to remove and reinstall the remote controller. Electric shock or fire may occur if you remove and reinstall
the remote controller yourself improperly.
• Make sure that the remote controller is mounted at locations which is able to provide full support to the weight of the remote controller. If
not, the remote controller may collapse and impose danger.
• Use specified cables to connect between indoor unit and remote controller. Selecting incorrect cables may lead to fire or electrical shock.
• Should abnormal situation arise (like burning smell), please stop operating the unit and turn off the circuit breaker. Contact your agent. Fault,
short circuit or fire may occur if you continue to operate the unit under abnormal situation.
• Always perform installation work with turn off the circuit breaker. Touch with energized electric parts causes an electric shock.
• The sales agent and qualified technician shall comply with local regulations or standards for the safety.
CAUTION
• Do not install the remote controller and cable at such places as;
- Where there is oil vapor and the oil is dispersed.
- Where the hot springs are near (in a sulfuric environment).
- Where generation, flowing, staying or leaking of flammable gas is detected.
- Where the sea is near (in the salty environment).
- An acid or alkaline environment.
• Do not install the indoor unit, outdoor unit, remote controller and cable within approximately 3 meters from strong electromagnetic wave
radiators such as medical equipment. In case that the remote controller is installed in a place where there is electromagnetic wave radiation,
shield the remote controller and cables by covering with the steel box and running the cable through the metal conduit tube.
• To avoid noise interference, please place the indoor unit and remote controller at least 1m away from TV/radio.
• This appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction. Children must be supervised not to play with the appliance.
2. INSTALLATION WORK
2.1 SELECTION OF INSTALLATION PLACE
Select a suitable place for handling and determine the installation place of the controller with the customer’s acceptance.
Do not install the controller at such places as:
- Where children can touch.
- Where the air from the air conditioner is directly discharged.
Especially in case that a Remote Controller thermostat is used, select the installation place in consideration with the following points:
- Where the average room temperature is detectable.
- Where the thermostat is not exposed directly to the sun.
- Where there is no source of heat.
- Where the thermostat is not affected with the outdoor air by opening and closing doors.
Prior to the installation work, ensure that foundation is flat, level and sufficiently strong and then fix the unit securely. If the foundation is not
strong enough, it may lead to injuries caused by falling of the product, electrical shock or fire.
2.2 BEFORE INSTALLATION
Check the contents and the number of the accessories in the packing.
Remote controller for
operation control
Connecting cable
2 screws M4x16L for
fixing the holding
bracket onto the wall
Manual CD
-2-
Installation manual
(This manual)
1 Insert the edge of the slotted screwdriver into the groove at the bottom of the holding bracket, push and then remove the remote controller
from holding bracket.
Rear cover
Approx. 6mm
Slotted Screw driver
Groove
Figure seen from bottom side
Groove for attaching controller
2 Attach the remote controller to holding bracket as follows.
Fix the holding bracket onto wall with screws(accessory) as shown right.
Fix the holding bracket with
the mark “UP” upward.
3 Cut the top of front cover and make a draw-out hole.
Lead the cable along the slot.
Cut and make a draw-out hole.
*Extended cable is prepared as an option. (SPX-WKT5M : 5m)
This cable can add until 2 pcs.
Lead the cable along the slot.
4 Insert the hooks of the controller to the holes on the top of the holding bracket. Push the lower part toward the holding bracket.
When the click sound is heard, the remote controller is attached to the holding bracket and the mounting work is finished.
Be careful not to pinch the cable when attaching it.
Remove the protection film from the liquid crystal display.
Remove the protection film
CAUTION
Pay attention so that the cable may not be bitten. It may cause a faulty operation.
-3-
English
2.3 INSTALLATION PROCEDURES
3. NAMES AND FUNCTIONS OF REMOTE CONTROLLER
The figure below shows all the indications for reference. The actual display during operation is different.
Display part
Eco Auto Off Indicator
It is indicated when the eco auto
off function is set.
Fan Speed Indicator
Auto Swing Indicator
Sleep Timer Indicator
It is indicated when the sleep timer
is set.
Room Temperature Indicator
(Around Remote Controller)
Timer Indicator
Operation Mode Indicator
It is indicated when the timer
function is set.
Eco Mode and Forced Cooling
setting, and External device
operation Indicator
Operation Lock Indicator
It is indicated when the operation
lock function is set.
Operation Guide Indicator
Filter Sign Indicator
Operation Indicator Lamp
It is indicated at the set period for
filter cleaning.
It lights while the unit is operated,
and it blinks in an abnormal
condition.
Setting Temperature Indicator
Menu Button
To display Menu.
Eco Button
By pressing this button during
operation, the unit performs the
eco operation.
START/STOP Button
(Operation indicator lamp)
Press this button to start operation.
Press it again to stop operation.
Enter Button
Cross Button
 : Up button
 : Down button
 : Left button
 : Right button
Operation part
NOTE
• Do NOT press the buttons hard or press with sharply pointed material such as a ball point pen.
The operation part of the remote controller may be damaged.
• Make sure that the buttons are pressed softly with fingers.
-4-
Return/Help Button
To return to the previous screen.
When pressed at the normal mode
screen, will display Help Menu.
5 After the setting is completed, press "OK" and the confirmation
screen will be displayed.
1 Press
. Select "Remocon Settings" from the menu and press "OK".
2 Select "Adjusting Date/Time" from the menu and press "OK".
6 Select "Yes" by pressing "" or "" and press "OK". The setting will
be confirmed and the screen will return to the normal mode.
3 Press "" or "" and select "yy/mm/dd/hh/mm".
4 Press "" or "" to change the setting. Press or keep
"" or "" to adjust numbers.
5. LANGUAGE SETTING
This function is used to change the displayed language.
3 Select "Yes" by pressing "" or "" and press "OK". The setting
will be confirmed and the screen will return to the normal mode.
1 Select "Language" from the menu and press "OK".
NOTE
2 Press "" or "" to select the language and press "OK".
The confirmation screen will be displayed.
If displayed language is changed, "Contact information"will be deleted.
-5-
English
4. ADJUSTING DATE/TIME
This function is used to adjust the date and time.
Periodic time setting is recommended. (Clock accuracy : Difference
within +/-5 seconds by month).
As for this remote controller, the clock can work up to 72 hours when
power failure occurs. Reset the date and time if the remote controller
remains without power supply for longer than 72 hours or main power
is OFF for long time.
6. SCREEN DISPLAY SETTING
This function is used to change the display adjustment.
◆ Function
• Time Format :
To change the time form to 12 hour 24 hour.
• Brightness :
To adjust the brightness of backlight.
• Back light :
To change the time (5, 15 or 30 seconds) between ON and OFF
of backlight.
• Contrast :
To adjust the degree of difference between light and dark parts
of LCD.
• On/Off lamp (Operation indicator lamp Brightness) :
To adjust the brightness of operation indicator.
• Brightness :
Press "" or "" and the brightness of backlight is changed.
• Back light :
The display backlight is OFF after the specified time interval of
inactivity (no input from touch screen).
The backlight off time interval can be selected as follows;
5 Seconds <--> 15 Seconds <--> 30 Seconds
• Contrast :
Press "" or "" and the degree of difference between light
and dark parts of LCD is changed.
• On/Off lamp :
Press "" or "" and the brightness of operation indicator
lamp is changed.
After the setting is completed, press "OK".
The confirmation screen will be displayed.
1 Select "Screen Display Setting" from the menu and press "OK".
2 Select the setting item by pressing "" or "". The indication is
changed in order of "Time Format", "Brightness", "Back light",
"Contrast" and "On/Off lamp".
4 Select "Yes" by pressing "" or " " and press "OK". The setting
will be confirmed and the screen will return to the normal mode.
3 Press "" or "" and set the display.
• Time Format :
The time form is changed as follows;
12 Hour <---> 24 Hour.
7. THERMISTOR SELECTION
This function is used to select the controlling thermistor.
1 Select "Thermistor Selection" from the menu and press "OK".
3 Select "Yes" by pressing "△ "or "▽ " and press "OK". The setting
will be confirmed and the screen will return to the normal mode.
2 By repeatedly pressing "" or "", the indication is changed in
order of IU <---> Remote control <---> Average.
Select the controlling thermistor and press "OK".
The confirmation screen will be displayed.
-6-
Room temperature(around remote controller) can be displayed
1 Press and hold
and
simultaneously for at least 3 seconds
during the normal mode (when unit is not operated).
The service menu will be displayed.
Select "Display room temp" from the service menu and press "OK".
The confirmation screen will be displayed.
2 Select "Yes" by pressing ""or "" and press "OK". The setting
will be confirmed and the screen will return to the normal mode.
English
8. DISPLAY ROOM TEMPERATURE (SERVICE MENU)
9. CONTACT INFORMATION REGISTRATION (SERVICE MENU)
Contact information can be registered from "Contact information".
1 Select "Contact information" from the service menu and press "OK".
The contact information 1 will be displayed.
5 Select "FIN." and press "OK" (or simply press
information 2" will be displayed.
). "Contact
2 Press
to change font type.
3 Press " " to select letter.
4 Press "OK" to confirm the letter. (Max.: 28 letters)
6 Repeat (3)-(5) to register the contact information 2.
Select "FIN." and press "OK", the confirmation screen will be displayed.
(Also press
and the confirmation screen will be displayed. )
7 Select "Yes" and press "OK". The service menu will be displayed
after setting is confirmed.
If "No" is pressed, the screen will return to (3).
-7-
Download PDF
Similar pages