Condiment Warmer
Instruction Manual
Models #2252EX & #2253EX
Model #2252EX
Model
#2253EX
Cincinnati, OH 45241-4807 USA
Part No. 38187EX
Revised June 1996
SAFETY PRECAUTIONS
This equipment is designed and sold for commercial use only. This
equipment is not to be used by the consumer in home use. Do not allow
direct contact of this equipment by the public when used in food service
locations. Only personnel trained and experienced in the equipment
operation may operate this equipment.
Carefully read all installation instructions before operating the equipment.
Always wear safety glasses when servicing this equipment.
NEVER put your fingers or any object into the heating area.
We do NOT assume any liability for injury due to careless
handling or operation of this equipment.
Any alterations to this equipment will void the warranty and
may cause a dangerous situation. NEVER make alterations
to the equipment.
Machine must be properly grounded to prevent electrical shock
to personnel.
Do NOT immerse the equipment in water.
Always unplug the equipment before cleaning or servicing.
NOTE
The information, specifications and illustrations contained in this manual represent
the latest data available at time of publication. Right is reserved to make changes as
required at the discretion of Gold Medal Products Company without notice.
Condiment Warmers
OPERATING INSTRUCTIONS
These warmers are designed for the purpose of warming food.
BEFORE PLUGGING IN UNIT
Warmer
should not be
operated
without water
in well.
1. Do not use the warmer without water. Fill water well with 709,7ml (24 Oz. by
volume) of water. Water does evaporate. With a setting of “HI” water will
completely evaporate in approximately 1 hour.
2. If pre-heating is desired set the heat control knob to “HI” for approx. 10
minutes. Prolonged setting of “HI” could result in overcooking.
3. Insert bowl into well.
4. Plug unit in socket.
5. Set control switch to desired setting.
6. Turn the heat control switch to the “OFF” position when The unit is not in
use. Do not overheat unit.
FOR UNITS EQUIPPED WITH A CONTAINER COVER
The cover is hinged in the center in order to access product without removing entire cover.
TO ATTACH COVER
Place cover directly over container with cover knob facing you. Make sure cover clips are
on the inside of bowl and press firmly until cover “snaps” into place. Cover must be entirely
off for proper cleaning.
INSTALLATION
CHECKING SHIPMENT
Unpack shipping carton and check thoroughly for any damage which may have occurred
during transit. Claims should be filed immediately with the transportation company.
ELECTRICAL REQUIREMENTS
Your Condiment Warmer is 230 Volts, 1500 Watts, 50 Cycle and will draw a maximum of 12.5
Amps. A standard 15 Amp grounded wall receptacle would be sufficient.
Machine must be properly grounded to prevent shock in case of
electrical problems.
1
ALL EXPORT MODELS #2252 AND #2253
Condiment Warmers
CARE AND CLEANING
Unplug the machine before cleaning. Do not immerse unit in
water.
Clean your machine daily. A clean, well kept machine is one of the best ways of advertising your
product.
Use a mild soap and damp cloth to clean the exterior of the unit.
All utensils and insert bowls should be cleaned with a chlorine or iodine type sanitizer to help
prevent contamination of microorganisms.
2
ALL EXPORT MODELS #2252 AND #2253
Condiment Warmers
MAINTENANCE INSTRUCTIONS
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO
ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE
NOT INTENDED FOR THE OPERATOR.
Adequate eye protection must be used when servicing this
equipment to prevent the possibility of injury.
Do NOT immerse the equipment in water.
Unplug your machine before servicing.
LIGHT BULB & SIGN REPLACEMENT
1.
2.
3.
4.
5.
Empty contents of bowl and remove.
Turn unit upside-down.
Remove the nine screws that hold the bottom plate.
Slide sign out from bottom.
You now have access to the light bulbs.
HEAT ELEMENT & THERMOSTAT REPLACEMENT
1.
2.
3.
4.
5.
Empty contents of bowl and remove.
Turn unit upside-down.
Remove the nine screws that hold the bottom plate.
Remove the two bolts holding the heat/thermostat cover.
Diconnect wires from thermostat and or heat element
6. Replace worn or broken parts, rewire per wiring diagram and reassemble.
3
ALL EXPORT MODELS #2252 AND #2253
Condiment Warmers
ORDERING SPARE PARTS
1. Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity desired.
3. Please include your model name and machine serial number (located on the machine
nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
(513) 769-7676
Fax: (513) 769-8500
E-mail: goldme19@eos.net
4
ALL EXPORT MODELS #2252 AND #2253
Condiment Warmers
11 QUART WARMER ASSEMBLY
5
ALL EXPORT MODELS #2252 AND #2253
Condiment Warmers
PARTS LIST – 11 QUART WARMER
Item No.
Part No.
1
2
3
4
5
6
7
8
9
10
38169
38172
38190
38177
38174
42369
41032
38179
38173
38105
38200
38106
38180
38138
38175
38076
38077
38203
87247
38225
38176
11
12
13
14
15
16
17
18
19
Description
Quantity
Well Body
Heat Plate
Heat Element (230V, 1500W)
Heating Plate Retainer
Thermostat Mounting Bracket
Lead–In Cord 230V
Pilot Light 230V Red
Heat Element Cover
Cabinet Assembly, Welded
Sign Cover, Lexan
Sign, Paper (Nachos)
Sign Cover, Acrylic
Heat Control Switch
Baffle
Well Retainer
Light Bulb 10 Watts, 250V
Bulb Socket
Sign Retainer, Welded
Bumper Rub
Sign Bracket
Bottom Plate
1
1
1
2
1
1
1
1
1
1
1
1
1
1
5
2
2
1
4
1
1
PARTS NOT SHOWN
38221
38188
38202
Blanket Insulation
Bottom Insulation
Front Panel S.S. (Model 2252EX Only)
ACCESSORY PARTS NOT INCLUDED WITH MACHINES
2255
38197
38198
38015
11 Quart Warmer Accessory Kit Includes
Hinged Cover, 11 Quart
11 Quart Food Container
2 Oz. Dipper
6
ALL EXPORT MODELS #2252 AND #2253
Condiment Warmers
ELECTRICAL SCHEMATIC
MODEL #2252EX
7
ALL EXPORT MODELS #2252 AND #2253
Condiment Warmers
ELECTRICAL SCHEMATIC
MODEL #2252EX L IGHTED
8
ALL EXPORT MODELS #2252 AND #2253
WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800428-2676 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, OH 45241-4807 USA
Download PDF
Similar pages