GANTRY® PULLDOWN FAUCET INSTALLATION INSTRUCTIONS

GANTRY PULLDOWN FAUCET
INSTALLATION INSTRUCTIONS
®
3700
4400
3710-12
4410-12
Gantry Model #:
3700
3710-12
3710-18
4400
4410-12
4410-18
3710-18
4410-18
INSTALLATION GUIDE
BEFORE YOU BEGIN YOUR INSTALLATION:
1
2
Turn off water supply.
3
Observe all local
plumbing codes.
4
Inspect waste and water
supplies for signs of damage.
Replace as necessary.
REQUIRED TOOLS:
DO NOT use petroleum
based products on this
faucet.
PARTS INCLUDED:
*XX represents finish
HK-THC-XX*
TRADITIONAL HANDLE CAP KIT (TRADITIONAL ONLY)
1. Adjustable Wrench
2. Phillips Screwdriver
LIFETIME WARRANTY
All Waterstone products manufactured by Waterstone carry a Limited
Lifetime Guarantee against functional defect in material or workmanship
in a residential application. Consult with an authorized Waterstone dealer for
complete information about our warranty.
For any questions or concerns about your faucet’s warranty, contact Waterstone.
Waterstone Faucets
41180 Raintree Court • Murrieta, CA 92562
1-888-304-0660
www.waterstoneco.com
HK-USM1250
UNDER SINK MOUNTING HARDWARE KIT (1-1/4”)
GANTRY® PULLDOWN FAUCET INSTALLATION
1.
3.
2.
C
4.
COUNTER
OR SINK
F
D
E
B
A
Fit flexible hoses (D, E) through
hole on counter or sink. (No
plumbers putty is required.
O-ring seals base).
Remove clamp nut (A) and
washer (B) from threaded
shroud (C).
Slide washer and thread the
clamp nut onto threaded
shroud. Tighten nut snug to
underside of sink or counter.
Turn faucet to the desired
handle position. Securely
tighten clamp screws (F).
CONNECTING SUPPLY HOSES
G
HANDLE POSITION
1. Before connecting supply hoses,
flush supply stops to clear any
debris. Place a bucket underneath
C 10D
stops andArun water Bfor 5 to
seconds. Turn water off.
2. Carefully position hot and cold
supplies so they will not interfere
with other hoses.
3. Connect supply hoses (A) to
B
supply stops (B). DO NOTAuse teflon
tape or plumbers putty. Turn water
back on and check for leaks. C D
Waterstone faucets are designed for 3 different faucet positions. Handle
on left, front and right. Your faucet is configured for the most common
ORIGINAL FACTORY POSITION
ADJUSTED POSITION
installation (see
below).
To reverse this andNEW
have
handle positioned on
MAY
HIT BACKSPLASH
CLEARSthe
BACKSPLASH
the left, connect the hose for cold water to the hot supply and the hose for
hot water to the cold supply. This will maintain the relationship of pulling
the handle for hot water or pushing for cold water.
H
E
F
A
B
F
C
E
OPTIONAL DECORATIVE CAPS
(TRADITIONAL ONLY - 3 INCLUDED)
H
C
COMPASS H/C
C
H
COMPASS C/H
FINISH MATCH
1. To remove, place a small standard screwdriver in
the slot at the bottom of metal ring that surrounds
the handle caps. Gently pry the cap from faucet
handle.
2. To replace, position cap and snap in with thumb.
HANDLE ON LEFT
HANDLE IN FRONT
HANDLE ON RIGHT
OPTIONAL HOT COLD INDICATOR RING
(CONTEMPORARY ONLY)
1. To reverse, or remove Hot and Cold Indicator
Ring, unscrew the metal cap, remove ring and flip.
2. Slide ring back onto handle and screw metal
cap back on.
RED FOR HOT
BLUE FOR COLD
HOW TO ADJUST HANDLE POSITION AND HANDLE TENSION
On some kitchen countertops, the handle
may hit the backsplash when the faucet
handle is positioned to the left or right
(Fig.
G 1). Waterstone gives you the option of
adjusting the handle 45 degrees to avoid
hitting backsplash.
D
E
FIG.1
ORIGINAL FACTORY POSITION
MAY HIT BACKSPLASH
F
NEW ADJUSTED POSITION
CLEARS BACKSPLASH
CONTEMPORARY
B
C
C D
1. Unscrew and remove the metal cap (A). Remove Hot and Cold Indicator Ring (B).
2. Unscrew and remove holding screw (C) and washer (D).
3. Hold handle (E) in a vertical position. Pull straight off faucet. Rotate handle
F from backsplash then slide handle back onto valve stem (F).
away
4. Insert holding screw with washer and tighten. Slide Hot and Cold Indicator
Ring onto handle and thread metal cap back into place.
A
5. To adjust handle tension, turn ring (G) clockwise to increase or
counterclockwise to decrease handle tension.
E
HANDLE ON LEFT
G
B
HANDLE IN FRONT
C D
E
F
HANDLE ON RIGHT
TRADITIONAL
1. Place a small standard screwdriver in the slot at the bottom of metal ring that surrounds the
handle caps (A). Gently pry the cap from faucet handle (B).
2. Unscrew and remove holding screw (C) and washer (D).
3. Hold the handle (B) in a vertical position. Pull straight off faucet. Rotate handle away from
backsplash then slide handle back onto valve stem (E).
4. Insert holding screw with washer and tighten. Snap handle cap back into place.
5. To adjust handle tension, turn ring (F) clockwise to increase or counterclockwise to decrease
handle tension.
B
A
H
F
C
C D
E
CLEANING AERATOR AND DEBRIS SCREEN
1.
2.
B
3.
4.
5.
C
A
Depending on quality of your household water, the aerator
and debris screen may become clogged. We recommend
cleaning one week after installation, then a minimum of
once of year thereafter. To remove the debris, follow the
steps below.
1. Gently unscrew and remove spout tip (A) by hand.
2. Remove O-ring (B). To remove aerator (C), push with finger from bottom.
3. Thoroughly rinse aerator with water until all debris is removed.
4. Place aerator, then O-ring back into spout tip.
5. Gently screw spout tip, by hand, snuggly back onto spout.
CARE AND CLEANING FOR WATERSTONE FAUCET FINISHES
ATTENTION: Waterstone offers many finishes for it’s products. Every finish is unique and requires different techniques for care and cleaning. Find
your product’s finish in the sections below, then carefully read and follow directions for that finish.
CLEAR PROTECTIVE COATED FINISHES
LIVING FINISHES
ABOUT YOUR FINISH:
These finishes have a clear protective
coating on them. Even though they have
a protective coating, they are only considered semi-durable. If the outside clear
coating is scratched or damaged in any
way, the base metal finishes exposed will
oxidize. Any use of an abrasive cleanser,
or any abrasive pad, cloth or sponge can
remove or dull the protective coating and
damage the finish. Some available sink
cleaners with bleach, soaps, and hand
lotions will damage the finish, as can
acidic organic cleansers. Always wipe your
fixture down with a clean soft cloth and
keep it clean and dry after use.
ABOUT YOUR FINISH:
Antique Bronze - ABZ
These finishes are considered Living Finishes
Black-Oil Rubbed Bronze - ORB
and have NO PROTECTIVE COATING on
them. Living finishes are finishes that have
Caribbean Bronze - CB
a very shallow patina on their surface. EsTuscan Brass - TB
sentially, the finish is what nature would do
Unlacquered Polished Brass - UPB
to the surface over a long period of time. The
Weathered Brass - WB
finishes are intended to change with time
Weathered Copper - WC
and generally darken slightly where they
are not being touched, and highlight where
the high use points are on the fixture. Hand oils, soaps, and acidic fluids and cleaners can
damage the finish. These finishes are not durable, and are easily scratched or scuffed.
Any type of astringent cleaner or any type of abrasive cleanser, pad, cloth or sponge will
damage the finish. To help keep the surface on the fixture from oxidizing in the packaging,
Waterstone initially applies a wax to the finish surface to help protect and prevent the
finish from exposure to air and oxidizing prior to installation.
Antique Brass - AB
Antique Copper - AC
American Bronze - AMB
Antique Pewter - AP
Distressed Antique Brass - DAB
Distressed Antique Copper - DAC
Distressed American Bronze - DAMB
Distressed Antique Pewter - DAP
Polished Brass - PB
Polished Copper - PC
Satin Brass - SB
Satin Nickel - SN
Venetian Bronze - VB
IMPORTANT NOTICE:
It is the responsibility of the customer to check for any material finish defects BEFORE
installation. Waterstone does not warranty these finishes AFTER installation.
SUGGESTED FINISH MAINTENANCE PROCEDURE:
1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done by using a mild diluted glass cleaner (we recommend
Windex). Apply the mild cleaner to a soft clean cloth, and periodically wipe your fixture
down to remove water spots and surface debris.
3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad
or sponge.
POWDER COATED FINISHES
ABOUT YOUR FINISH:
Almond - 01
These finishes are powder coated color finishes. They
have NO ADDITIONAL PROTECTIVE COATING. These
Black - 06
finishes are not considered durable finishes and can be
Biscuit - 07
scratched, chipped or scuffed. If the exterior color coating
Chocolate Bronze - CHB
is damaged, the exposed metal base will oxidize. Any
Euro-White - EW
use of an abrasive cleanser, or any abrasive pad, cloth or
Matte Black - MB
sponge can remove or dull the color coating and damage
White - WT
the finish. Some available sink cleaners with bleach,
soaps, and hand lotions will damage the finish, as can
acidic organic cleansers. Always wipe your fixture down with a clean soft cloth and keep it
clean and dry after use.
IMPORTANT NOTICE:
It is the responsibility of the customer to check for any material finish defects BEFORE
installation. Waterstone does not warranty these finishes AFTER installation.
SUGGESTED FINISH MAINTENANCE PROCEDURE:
1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done by using a mild diluted glass cleaner (we recommend
Windex). Apply the mild cleaner to a soft clean cloth, and periodically wipe your fixture
down to remove water spots and surface debris.
3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad
or sponge.
IMPORTANT NOTICE:
It is the responsibility of the customer to check for any material finish defects BEFORE
installation. Waterstone does not warranty these finishes AFTER the fixture has been
installed.
SUGGESTED FINISH MAINTENANCE PROCEDURE FOR ANTIQUE BRONZE, CARIBBEAN
BRONZE, TUSCAN BRONZE, UNLACQUERED POLISHED BRASS AND WEATHERED BRASS:
1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done by using a micro-crystalline wax (we recommend Renaissance Wax). Apply the wax with a soft non-abrasive tissue paper, and gently buff the wax
with a soft clean cloth to help remove surface spots and add a protective coating to the
finish.
3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive
pad or sponge.
SUGGESTED FINISH MAINTENANCE PROCEDURE FOR BLACK-OIL RUBBED BRONZE:
1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done by applying mineral oil to a clean soft cloth and gently
wiping down the finish surface to clean. Make sure not to rub too hard, in that you can
remove too much of the surface patina surface with aggressive cleaning.
3. Once the mineral oil has been applied, with a clean soft dry cloth gently pat the finish
surface to remove any excess oil on the fixture to until the fixture no longer looks “wet”.
4. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive
pad or sponge.
SUGGESTED FINISH MAINTENANCE PROCEDURE FOR WEATHERED COPPER:
1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done by applying denatured isopropyl alcohol to a clean soft
cloth and gently wiping down the finish surface to clean. Do not rub too hard, in that you
can remove too much of the surface patina. This step will leave the finish looking a shade
darker.
3. Using a different soft clean cloth, apply a non-abrasive metal polish (we recommend
“Miracle Shine” by GSM) to the cloth and gently rub the polish into the finish. This will
clean, protect, and brighten up the finish after it was left darker from the alcohol cleaning
in step 2.
4. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive
pad or sponge.
CONTINUED ON NEXT PAGE...
CARE AND CLEANING FOR WATERSTONE FAUCET FINISHES (Cont.)
PLATED FINISHES
STAINLESS STEEL
ABOUT YOUR FINISH:
Black Nickel - BLN
These finishes are the most durable finishes Waterstone
offers. The best general maintenance is regular cleaning.
Chrome - CH
Even though these finishes are considered durable, you
Polished Nickel - PN
can never use any abrasive type cleaners, clothes, or pads
Satin Chrome - SC
to clean your fixture. Always try and keep your finishes
clean and dry. Trapped moisture on the surface of your
finish can lead to staining. Astringent cleaners, chlorine, bleach, along with acidic based
organic cleansers are potentially harmful to these finishes. Chrome plated finishes are very
tarnish resistant. However, they are not indestructible and can scratch and mar.
ABOUT YOUR FINISH:
Stainless Steel - SS
Waterstone’s stainless steel fixtures are actually made of
solid stainless. This finish has NO PROTECTIVE COATING
on it. Stainless steel is by its material nature very tarnish
resistant, but by no means tarnish or stain proof. This finish will indeed oxidize naturally
over time and react to its environment, and in a reaction to some chemical cleaners that
have bleach in them rusting can be induced on the finish. Keep your stainless fixture wiped
clean and dry, and use only a cleaner specifically made for stainless steel. Trapped moisture
on the surface of your finish can lead to staining. Astringent cleaners, chlorine, bleach,
along with acidic based organic cleansers are potentially harmful to stainless steel finishes.
IMPORTANT NOTICE:
It is the responsibility of the customer to check for any material finish defects BEFORE
installation. Waterstone does not warranty these finishes AFTER the fixture has been
installed.
IMPORTANT NOTICE:
It is the responsibility of the customer to check for any material finish defects BEFORE
installation. Waterstone does not warranty these finishes AFTER the fixture has been
installed.
SUGGESTED FINISH MAINTENANCE PROCEDURE:
1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done by applying denatured isopropyl alcohol with a soft clean
cloth to gently remove surface spots.
3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad
or sponge.
SUGGESTED FINISH MAINTENANCE PROCEDURE:
PRECIOUS METALS
ABOUT YOUR FINISH:
Polished Gold - PG
This finish is done with real precious metal gold plating
on the brass fixture surface. This finish has NO PROTECSatin Gold - SG
TIVE COATING and is extremely soft. Some or all of the
Gold plating will be removed if any type of polish is used.
Additionally, the finish will wear aware with time. The gold plating is considered very
delicate and can be easily scratched or scuffed. Any type of astringent cleaner or any type
of abrasive cleanser, pad, cloth or sponge will damage the finish.
IMPORTANT NOTICE:
It is the responsibility of the customer to check for any material finish defects BEFORE
installation. Waterstone does not warranty these finishes AFTER the fixture has been
installed.
SUGGESTED FINISH MAINTENANCE PROCEDURE:
1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done with mild liquid soap only. Wipe gently with a soft cloth
to clean.
3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive
pad or sponge.
41180 Raintree Court • Murrieta, CA 92562
1-888-304-0660 • 951-304-0520
www.waterstoneco.com
VEN-038-GANT Rev. B
1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done by applying a “stainless steel cleaner” with a soft clean
cloth to gently remove surface spots and brighten the finish.
3. Never use cleaners with bleach, abrasives, or vinegar. Never use any type of abrasive pad
or sponge.
Download PDF
Similar pages