Installation Instructions / Warranty

Installation Instructions / Warranty
C
04221xx0
E
04226xx0
S
04231xx0
Trim, Thermostat with Volume Control / Diverter
04221xx0
04226xx0
04231xx0
Technical Information / Données techniques / Datos tecnicos
Recommended water
pressure
Pression d’eau recommandée Presión recomendada
en servicio
15 - 75 PSI
Max. water pressure
Pression d’eau maximum
Presión en servicio max.
145 PSI
Recommended hot
water temp.
Température recommandée
d'eau chaude
Temperatura recomendada del agua caliente
120� - 140� F*
Max. hot water temp
Température maximum d'eau
chaude
Temperatura del agua
caliente max.
176�F*
Flow rate @ 44 PSI
Capacité nominale
Caudal máximo
8 GPM
*Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.
* Vous devez connaître et respecter tous les codes de plomberie locaux applicables pour le réglage de la température du
chauffe-eau.
*Debe conocer y cumplir todos los códigos locales aplicables para ajustar la temperatura del calentador de agua.
Installation Considerations
• For best results, Hansgrohe recommends that
this unit be installed by a licensed, professional plumber.
• Please read over these instructions thoroughly before beginning installation. Make sure
that you have all tools and supplies needed
to complete the installation.
• This trim is for use with iBox Universal Plus
model 01850181 (not included).
• To prevent scald injury, the maximum output
temperature of the shower valve must be
no higher than 120°F. In Massachusetts,
the maximum output temperature can be no
higher than 112° F.
• Keep this booklet and the receipt (or other
proof of date and place of purchase) for
this product in a safe place. The receipt is
required should it be necessary to request
warranty parts.
À prendre en considération pour l’installation
• Pour de meilleurs résultats, Hansgrohe
recommande que ce produit soit installé par
un plombier professionnel licencié.
• Ce dispositif requiert une pièce intérieure
01850181.
• Veuillez lire attentivement ces instructions
avant de procéder à l’installation. Assurezvous de disposer de tous les outils et du
matériel nécessaires pour l’installation.
du robinet de douche ne doit pas excéder
120°F. Au Massachusetts, la température
de sortie maximale du robinet de douche ne
doit pas excéder 112°F.
• Conservez ce livret et le reçu (ou une autre
preuve sur laquelle figurent la date et
l’endroit de l’achat) pour ce produit dans
un endroit sûr. Le reçu est requis si vous
commandez des pièces sous garantie.
• Pour empêcher des blessures par ébouillantement, la température de sortie maximale
Consideraciones para la instalación
• Para obtener mejores resultados, Hansgrohe
recomienda que la instalación de esta unidad esté a cargo de un plomero profesional
matriculado.
• La unidad requiere una pieza interior de
válvula 01850181.
• Antes de comenzar la instalación, lea estas
instrucciones detenidamente. Asegúrese
de tener las herramientas y los insumos
necesarios para completar la instalación.
• Mantenga este folleto y el recibo (u otro
comprobante del lugar y fecha de compra)
de este producto en lugar seguro. El recibo
se requiere en caso de ser necesario solicitar
piezas bajo garantía.
• Para evitar escaldaduras, la máxima
temperatura de salida de la válvula de la
ducha no debe exceder los 120°F. En
Massachusetts, la máxima temperatura de
salida de la válvula de la ducha no debe
exceder los 112°F.
Service Stops / Butées d’arrêt d’isolation / Cierres de servicio
closed
ferme
cerrado
open
ouvert
abierto
English
Installation
Flush the hot and cold supplies
(1) Remove the dust cover.
2.
(2) Open the stops using a 4 mm Allen wrench.
4 mm
2.
1.
Allow the hot and cold supplies to flush for at
least 5 minutes.
Close the stops using a 4 mm
Allen wrench.
Cut the plaster shield so that it extends ¹⁄₁₆" - ⅛"
from the finished wall surface.
Français
Español
Installation
Instalación
Rincez les conduites d’alimentation de
l’eau chaude et de l’eau froide
Lave los suministros frío y caliente
(1) Retirez l’étiquette.
(2) Ouvrez l’eau à les butées d'arrêt d'isolation à
l’aide d’une clé hexagonale de 4 mm.
Rincez les conduites de l’eau pour au moins 5
minutes.
Fermez l’eau à les butées
d'arrêt d'isolation à l’aide
d’une clé hexagonale de 4
mm.
Coupez le protecteur de façon à ce qu’une
partie de ¹⁄₁₆ à ⅛ po soit à l’extérieur de la
surface du mur fini.
(1) Retire la etiqueta.
(2) Abra los pasos del agua en los cierres de
servicios con una llave Allen de 4 mm.
Lave los suministros de agua para por lo menos
cinco minutos.
Cierre el paso del agua en la
entrada del suministro o los
cierres de servicio con una
llave Allen de 4 mm.
Corte el protector de yeso de modo que
sobresalga ¹⁄₁₆" - ⅛" de la superficie de la
pared terminada.
English
1.
Seal the wall around the
plaster shield with waterproof
sealant (1).
Failure to seal the wall
can lead to possible water
damage.
Remove the flush insert screw, flush insert, and
seals (2).
2.
Insert the function block.
Install and tighten the function block screws using
a 4 mm Allen wrench.
Measure the distance from the front of the plaster
shield to one of the screw-in flanges ("X").
Français
Español
Scellez le mur autour du
protecteur à l’aide d’un agent
d’étanchéité.
Selle la pared alrededor del
protector de yeso con un
sellador impermeable.
Si le mur n’est pas scellé,
l’eau pourrait éventuellement
causer des dommages.
Si no se sella la pared, pueden
producirse daños por acción
del agua.
Retirez la vis de la pièce d’insertion affleurante,
la pièce d’insertion affleurante, et les joints (2).
Quite los tornillos del inserto de lavado, el
inserto de lavado, y las juntas (2).
Insérez le bloc de fonction.
Inserte el bloque de función.
Installez les vis du bloc de fonction à l’aide d’une
clé hexagonale de 4 mm.
Instale los tornillos del bloque de función con
una llave Allen de 4 mm.
Mesurez la distance entre la surface du mur et la
bride du vis. Notez la longueur mesurée (« X »).
Mida la distancia entre la superficie de la pared
y la brida de tornillo. Anote esta medida (“x”).
English
Add ½" to this measurement.
Cut each screw so that it is X + ½" long.
Open the stops (1).
1.
Install the carrier plate so that the notch is at the
bottom (2).
Install the carrier plate screws.
2.
Push the thermostatic mixer sleeve on so that the
indexing mark is at the 12:00 position.
Push the volume control sleeve on.
Install the escutcheon.
Français
Español
Ajoutez ½ po à cette longueur « X ». Notez cette
longueur.
Agregue ½" a X. Anote esta medida.
Coupez les vis de façon à ce que celui-ci
dépasse de ½ po + la longueur X.
Ouvrez les butées d'arrêt d'isolation (1).
Installez la plaque-support de façon à ce que
l’encoche soit vers le bas (2).
Installez les vis de la plaque-support.
Corte el tornillo de modo que sobresalga ½" +
X.
Abra el paso del agua en los cierres de servicio
(1).
Instale la placa del portador de manera que la
ranura quede en la parte inferior (2).
Coloque los tornillos de la placa del portador.
Installez la douille thermostatique de façon à ce
que la marque de repère soit à la position 12:00.
Instale el casquillo de manera que la marca
indicadora quede en posición de 12:00.
Installez la douille inverseur / arrêt.
Instale el casquillo del llave de paso /
distribuidor.
Installez le rosace.
Instale el florón.
English
Place a dab of waterproof sealant at each grout
joint.
Lubricate the adapter stems with a small amount
of white plumber's grease (1).
Install the handle adapters and screws (2).
Tighten the screws using a 3 mm Allen wrench.
1.
2.
2.
Install the volume control handle (1). Tighten the
screw using a 2 mm Allen wrench.
1.
Install the thermostatic mixer handle so that the
safety stop override button is at the 9:00 position
(2).
Tighten the handle screw using a 2.5 mm Allen
wrench.
10
Français
Español
Appliquer une petite quantité de l’agent
d’étanchéité aux joints de coulis.
Coloque un poco de sellador a prueba de agua
en las uniones de la lechada de cemento.
Lubrifiez la tige de manoeuvre avec une petite
quantité de graisse de plomberie blanche (1).
Lubrique el vástago de la válvula con una pequeña cantidad de grasa blanca para plomería (1).
Installez l’adaptateurs de poignées (2). Serrez
les vis à l’aide d’une clé hexagonale de 3 mm.
Instale el adaptador del mando (2). Apriete los
tornillos con una llave Allen de 3 mm.
Installez le poignée d'arrêt (1).
Instale el mando del llave de paso (1).
Installez la poignée thermostatique de façon à
ce que le bouton de surpassement de la butée
de sécurité soit à la position 9:00 (2).
Instale el mando termostatico de manera que el
botón de vencimiento de tope de seguridad se
encuentre en una posición de 90 grados (2).
Serrez la vis de la poignée à l’aide d’une clé
hexagonale de 2.5 mm.
Ajuste el tornillo del mando con una llave Allen
de 2.5 mm.
11
English
Set the high temperature limit
stop**
Remove the clip and stop ring from the cartridge
stem.
Turn the water on to one of the functions.
Turn the cartridge stem until the output water
is the desired high temperature, usually 110°
- 112° F**.
Replace the stop ring so that the tooth is against
the cartridge stop. Replace the clip.
It should not be possible to turn the stem further
counter-clockwise.
**Follow all applicable local plumbing codes when setting the
high temperature limit stop.
12
Français
Español
Réglez la butée de limite
d’eau chaude**
Fije el tope de límite de alta
temperatura**
Retirez l’étrier et la bague de retenue de la tige
de la cartouche.
Retire la presilla y el aro de tope del vástago del
cartucho.
Faites couler l’eau en utilisant l’une des fonctions.
Abra el paso del agua a una de las funciones.
Tournez la tige de la cartouche jusqu’à ce que
l’eau chaude soit à la température souhaitée,
normalement entre 43 et 44 °C (110 et 112
°F)**.
Gire el vástago del cartucho hasta que el agua
de salida tenga la temperatura alta deseada,
normalmente entre 43 et 44 °C (110 et 112
°F)**
Remettez la bague de retenue en place de façon
à ce que la dent s’appuie sur la butée de la
cartouche. Remettez l’étrier en place.
Reemplace el aro de tope de manera que
el diente esté contra el tope del cartucho.
Reemplace la presilla.
La tige ne doit pas pouvoir tourner plus loin dans
le sens antihoraire.
No debería ser posible girar más el vástago en
sentido antihorario.
13
English
Justify the handle
Loosen the handle screw. Remove the handle.
Turn the cartridge stem until the output water is
100° F.
Install the handle so that the override button is
next to the sleeve indexing mark.
Tighten the handle screw.
14
Français
Español
Réglez la poignée
Ajuste el mando
Desserrez la vis de la poignée. Retirez la
poignée.
Afloje el tornillo del mando Retire el mando.
Tournez la tige de la cartouche jusqu’à ce que
l’eau soit à une température de 100 °F.
Gire el vástago del cartucho hasta que el agua
de salida esté en100 °F.
Installez la poignée de façon à ce que le bouton
de surpassement soit près de la marque de
repère du manchon.
Instale el mando de manera que el botón de
vencimiento se encuentre al lado de la marca
indicadora del casquillo.
Serrez la vis de la poignée.
Apriete el tornillo del mando.
15
English
Modify the diverter to allow
simultaneous use of both
functions
Do not carry out this
modification if:
• your local plumbing code does not allow the
use of two shower functions simultaneously.
• the homeowner does not desire this ability.
Remove the diverter cartridge stop ring.
Turn the diverter handle so that the indexing mark
is at the 6:00 position to obtain water from both
functions simultaneously.
16
Français
Español
Modifiez l'inverseur pour
permettre l’usage simultané
des deux fonctions
Modifique el diverter para
permitir el uso simultáneo de
ambas funciones
Ne pas exécuter cette
modification si :
No lleve a cabo esta
modificación si:
• Votre code local de plomberie ne permet
pas l’usage de deux fonctions de douche
simultanément.
• Le propriétaire ne désire pas cette capacité.
• Su código local de la plomería no permite el uso de dos funciones de ducha
simultáneamente.
• El propietario no desea esta capacidad.
Retirez l’anneau d’arrêt de cartouche de diverter.
Quite el anillo de la parada de cartucho de
diverter.
Tourner la poignée de diverter pour que
la marque d’indexation est à la 6:00 position d’obtenir de l’eau des deux fonctions
simultanément.
Gire el asidero de diverter para que el indexando marca está en la 6:00 posición de obtener
agua de ambas funciones simultáneamente.
17
Clean the cartridge filters
Remove the trim.
Close both stops using a 4 mm Allen wrench.
4 mm
Remove the thermostatic cartridge using a
wrench.
Rinse the filters using clear water.
Replace the thermostatic cartridge.
Open the stops.
Replace the trim.
18
Nettoyez les filtres
Limpiar los filtros
Retirez le jeu de garniture.
Retire el juego de la pieza exterior.
Fermez l'eau à les butées d'arrêt d'isolation à
l'aide d'une clé hexagonale de 4 mm.
Cierre el paso del agua en la entrada del
suministro o los cierres de servicio con una llave
Allen de 4 mm.
Retirez la cartouche thermostatique à l'aide
d'une clé.
Retire el cartucho termostatico.
Lave los filtros.
Rinez les filtres avec l'eau claire.
Remplacez la cartouche thermostatique.
Instale el cartucho termostatico.
Ouvrez l'eau à lex butées d'arrêt d'isolation.
Abra el paso del agua en la entrada del
suministro o los cierres de servicio con una llave
Allen de 4 mm.
Remplacez le jeu de garniture.
Instale el juego de la pieza exterior.
19
Troubleshooting
Problem
Insufficient water
Possible Cause
Solution
Supply pressure inadequate
Check water pressure
Cartridge filters dirty
Clean the filters (see page
18)
Showerhead or handshower filter dirty
Clean the filter
Crossflow: hot water forced into
cold water supply or vice versa
when mixture is closed
Check valves dirty or worn
Clean check valves, replace
if necessary
Output temperature does not
correspond with temperature
marked on handle
Handle not justified
Justify the handle
Water heater set too low
Increase the hot water
temperature
Safety stop button not operating
Button and/or spring are dirty or worn
Clean spring and button,
replace if necessary
Handle hard to turn
Cartridge dirty or worn
Replace cartridge
Shower or spout dripping
Volume control cartridge dirty or worn
Clean or replace volume
control cartridge
Temperature regulation not
possible
(new installation) Hot and cold supplies
are reversed
Turn the function block
180°
Thermostatic cartridge dirty or worn
Replace the thermostatic
cartridge
Dépannage
Dysfonctionnement
Pas assez d´eau
Origine
Pression d´alimentation insuffisante
Filtre de l´élément thermostatique
encrassé
Joint-filtre de douchette encrassét
Circulation opposée, l´eau chaude
est comprimée dans l´arrivée d´eau
froide et vice versa avec robinet fermé
La température à la sortie ne
correspond pas à la température de
réglage
Le réglage de la température n´est
pas possible
Clapet anti-retour encrassé ou
défectueux
20
Clapet anti-retour encrassé ou
défectueux
L´élément thermostatique est encrassé
ou entartré
La pièce de base a une alimentation
inversée (l´eau froide doit être à
droite et l´eau chaude à gauche) ou
elle est montée à l´envers
Solution
Contrôlez la pression
Nettoyez les filtres (voir p.
18)
Nettoyez le joint-filtre entre
la douchette et le flexible
Nettoyez le clapet antiretour ou le changez
éventuellement
Réglez le thermostat
Nettoyez l´élément
thermostatique ou le
changez éventuellement
Montez le bloc de fonction
à 180°
Dysfonctionnement
Bouton à pression du verrouillage de
sécurité défectueux
Origine
Ressort défectueux
Bouton à pression entartré
Fonctionnement de la poignée difficile Mécanisme d´arrêt défectueux
La douchette ou le bec verseur goutte De la saleté ou de l´incrustation
sur le siège, mécanisme d´arrêt
défectueux
Solution
Nettoyez le ressort ou bien
le bouton à pression, le
changez éventuellement
Changez le mécanisme
d´arrêt
Nettoyez le mécanisme
d´arrêt
ou le changez
éventuellement
Troubleshooting
Problema
Sale poca agua
Causa
presión insuficiente
filtro del termoelemento sucio
filtro de la ducha sucio
Flujo de agua cruzada agua caliente válvula antirretorno sucia o pierde
entra en la tubería del agua fría o
al revés
Temperatura del agua no
termostato no ha sido ajustado
corresponde a lo marcado
No es posible regular la temperatura termoelemento sucio/lleno de cal
cuerpo empotrado mal montado
(debe estar: frío = derecha) o
instalado girado en 180°
Botón de tope no funciona
muelle defecto
botón lleno de cal
Llave de paso va duro
montura dañada
Llave de paso pierde agua
suciedad/cal en el asiento de la
junta o montura dañada
Solución
comprobar presión
limpiar filtro (ver página 18)
limpiar / cambiar filtros entre
flexo y ducha
limpiar / cambiar válvula
ajustar termostato
limpiar / cambiar
termoelemento
girar embellecedor en 180°
limpiar / cambiar
cambiar montura
limpiar / cambiar montura
21
Replacement Parts / Pièces détachées / Repuestos
22
7
11
23
10
21
16
9
5
17
29x3
14
8
6
2
4
48x3
3
23
15
1
24
5
29x3
12
14
6
4
23
48x3
20
18
15
13
22
19
1
E thermostat handle
poignée thermostatique E
mando del termostato E
88771xx0
2
E volume control handle
poignée E
mando E
88768xx0
3
escutcheon
rosace
florón
96552xx1
4
sleeve
douille
casquillo
95550xx0
5
sleeve
douille
casquillo
95253xx0
6
fixing screw (set)
vis du support (set)
tornillo portador (set)
96454000
7
carrier plate
support de rosace
portador florón
96647000
8
thermostatic cartridge
cartouche thermostatique
termoelemento
94282000
9
noise reducer
silencieux
silenciador
94073000
10
check valve
clapet anti-retour
válvula antirretorno
94074000
11
volume control /diverter
cartridge
mécanisme d'arret /
inverseur
montura llave de paso / 98283000
distribuidor
12
extension
rallonge 25 mm
alargo 25 mm
13595000
13
extension
rallonge 22 mm
alargo 22 mm
13596000
14
handle adapter
adapteur pour poignée
adaptador mando
88772000
15
handle adapter
adapteur pour poignée
adaptador mando
96435000
16
o-ring 16 x 2
joint torique 16 x 2
junta toroidal 16 x 2
98133000
17
sealing set
set de joint
junta
95037000
18
C escutcheon
rosace C
florón C
95556xx1
19
C thermostat handle
poignée thermostatique C
mando del termostato C 88773xx0
20
C volume control handle
poignée C
mando C
88770xx0
21
S thermostat handle
poignée thermostatique S
mando del termostato S
88772xx0
22
S volume control handle
poignée S
mando S
88769xx0
23
screw cover
cache vis
tapón
95181000
24
carrier plate
support de rosace
portador florón
98793000
xx
00 62
82
83
92
93
= Finishes / Couleurs / Acabados
= chrome
= oil rub bronze
= brushed nickel
= polished nickel
= rubbed bronze
= polished brass
23
Cleaning Recommendation for Hansgrohe Products
Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with
regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
Cleaning Materials for Faucets and Showers
Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points when
cleaning faucets and showers:
•
Only use cleaning materials which are explicitly intended for this type of application.
•
Never use cleaning materials which contain hydrochloric, formic, phosphoric, or acetic acid, as they cause considerable
damage.
•
Never mix one cleaning material with another.
•
Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads, or micro
fiber cloths.
Cleaning Instructions for Faucets and Showers
Please follow the cleaning material manufacturer’s instructions. In addition, pay attention to the following points:
•
Clean the faucets and showers as and when required
•
Use the amount of cleaning product and the amount of time recommended by the manufacturer. Do not leave the cleaner on the
fixture longer than necessary.
•
Regular cleaning can prevent calcification.
•
When using spray cleaners, spray first onto a soft cloth or sponge. Never spray directly onto the faucet as droplets can enter
openings and gaps and cause damage.
•
After cleaning, rinse thoroughly with clean water to remove any cleaner residue.
Important
Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using.
Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage.
Components with damaged surfaces must be replaced or injury could result.
Damage caused by improper treatment is not covered under the warranty.
Recommandations pour le nettoyage des produits Hansgrohe
Les robinetteries modernes de lavabo, de cuisine et de douche utilisent des matériaux très différents pour répondre aux besoins du
marché en termes de conception et de fonctionnalité.����������������������������������������������������������������������������
Certaines règles de base doivent être respectées lors du nettoyage de ces
��������������������������������������������������������������������������
produits afin d’éviter de les endommager ou d’avoir à les retourner.
Produits de nettoyage pour robinetteries et douches
Les acides sont une partie intégrante nécessaire de tous les produits de détartrage; il faut cependant prendre les précautions suivantes
lors du nettoyage des robinets et des douches :
•
N’utilisez que des produits/articles de nettoyage conçus spécifiquement pour les articles de robinetterie et de douche.
•
N’utilisez jamais de produits/articles de nettoyage contenant de l’acide chlorhydrique, formique, phosphorique ou acétique car
ils pourraient causer des dommages considérables.
•
Ne mélangez jamais deux produits de nettoyage.
•
N’utilisez jamais de produits/articles de nettoyage de nature abrasive tels que poudres de nettoyage, tampons-éponge ou
chiffons microfibre non appropriés.
Instructions de nettoyage pour robinetteries et douches
Veuillez suivre les instructions du fabricant de produits/articles de nettoyage.�����������������������������������������������
De plus, tenez compte des conseils suivants :
���������������������������������������������
Nettoyez vos produits de robinetterie et de douche aussi souvent que nécessaire.
•
24
Utilisez la quantité de produit nettoyant et respectez la durée recommandée par le fabricant.������������������������������������
Ne laissez pas le produit sur les
����������������������������������
articles de robinetterie plus longtemps que nécessaire.�
•
Un nettoyage régulier peut prévenir la formation de dépôts calcaires.
•
Si vous utilisez des nettoyants en vaporisateur, vaporisez d’abord sur une éponge ou un chiffon.������������������������������
Ne vaporisez jamais directe����������������������������
ment sur un robinet : des gouttelettes pourraient s’infiltrer dans les ouvertures et les interstices et endommager celui-ci.
•
Après le nettoyage, rincez abondamment avec de l’eau propre pour éliminer tout résidu de produit nettoyant.
Important
Les résidus de savon liquide, de shampoing et de mousse pour la douche peuvent également endommager la robinetterie; rincez
donc avec de l’eau propre après utilisation de ces produits.
Veuillez noter : �����������������������������������������������������������������������������������������
si la surface est déjà endommagée, les produits de nettoyage l’endommageront encore plus.
Les composants dont la surface est endommagée devraient être remplacés sous peine d’entraîner des
blessures.�
Les dommages dus à un mauvais traitement ne sont pas couverts par la garantie.
Recomendación de limpieza para los productos de Hansgrohe
Hoy en día, las griferías de baño y de cocina así como duchas modernas se componen de materiales muy distintos para satisfacer
las exigencias del mercado respecto al diseño y la funcionalidad. Para evitar daños reclamaciones hay que tener en cuenta ciertos
aspectos tanto en el uso como en su limpieza posterior.
Para elucidado de las griferías y las duchas en principio hay que seguir lo siguiente:
•
Usar sólo detergentes previstos específicamente para este campo de aplicación.
•
No aplicar detergentes que contengan hipoclorito sódico, ácido clorhídrico, fórmico o acético porque pueden causar daños
importantes.
•
Detergentes que contienen ácido fosfórico tampoco pueden ser aplicados ilimitadamente.
•
Por regla general no se deben mezclar detergentes.
•
Tampoco se deben utilizar utensilios abrasivos, como son polvos abrasivos, esponjas o paños de microfibra.
•
Si tienen que seguir siempre las instrucciones de uso de los fabricantes de los detergentes.
•
La limpieza tiene que ser realizada según la dosificación y el tiempo de actuación, en función del objeto y ajustada a las
necesidades específicas del mismo.
•
Gracias a una limpieza periódica se pueden evitar las incrustaciones de cal.
•
No conviene rociar el detergente en ningún caso sobre la grifería sino sobre los textiles y ejecutar la limpieza así porque el
líquido puede entra en aperturas o hendiduras de la grifería y causar daños.
•
Después de la limpieza hay que aclarar con suficiente agua para eliminar completamente el resto de detergente.
•
La utilización de limpiadores a vapor no está permitida, las altas temperaturas pueden dañar los productos.
Indicaciones importantes
Los residuos de productos de aseo como jabón líquido, champús y gel de ducha pueden dañar también los materiales.
Por lo que también se deberá prestar atención a lo siguiente: aclarar con abundante agua después del uso.
Con materiales ya dañados la acción de detergentes incrementará el desgaste de estos.
Los componentes con superficies dañadas deberán cambiarse, en otro caso se corre el peligro de lesionarse.
Los daños que resulten de un uso inadecuado no están incluidos en nuestra garantía.
25
Limited Lifetime Consumer Warranty
This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is
limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either
the United States or Canada.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original consumer purchaser only. This warranty is non-transferable.
WHAT IS COVERED BY THE WARRANTY
This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material or
workmanship as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product or part of the product
that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. If
Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made, Hansgrohe may elect to refund
the purchase price in exchange for the return of the product.
LENGTH OF WARRANTY
Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If
you are a consumer who purchased the product for use primarily for personal, family, or household purposes, this warranty extends
for as long as you own the product and the home in which the product is originally installed. If you purchased the product for use
primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with
respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products.
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR:
A. Conditions, malfunctions or damage not resulting from defects in material or workmanship.
B.
Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper maintenance,
misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no-rinse” cleaning
products, or the use of the product in any manner contrary to the product instructions. (3) Conditions in the home such as excessive water pressure or corrosion.
C. Labor or other expenses for the disconnection, deinstallation, or return of the product for warranty service, or for installation or
reinstallation of the product (including but not limited to proper packaging and shipping costs), or for installation or reinstallation
of the product.
D. Accessories, connected materials and products, or related products not manufactured by Hansgrohe.
TO OBTAIN WARRANTY PARTS OR INFORMATION
Contact your Hansgrohe retailer, or contact Technical Service at:
Hansgrohe Inc.
1492 Bluegrass Lakes Parkway
Alpharetta GA 30004
Toll-free (800) 334-0455.
In requesting warranty service, you will need to provide
1.
The sales receipt or other evidence of the date and place of purchase.
2. A description of the problem.
3. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc. 1492
Bluegrass Lakes Parkway, Alpharetta, Georgia 30004, Attention: Technical Service, if required by Hansgrohe.
When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid.
EXCLUSIONS AND LIMITATIONS
REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY
PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT.
HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL, SPECIAL, OR
CONSEQUENTIAL DAMAGES, ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY (INCLUDING
MERCHANTABILITY).
26
Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from State to State. You may
be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in
court against us under the Magnuson-Moss Warranty Act.
PRODUCT INSTRUCTIONS AND QUESTIONS
Upon purchase or prior to installation, please carefully inspect your Hansgrohe product for any damage or visible defect. Prior to
installing, always carefully study the enclosed instructions on the proper installation and the care and maintenance of the product. If
you have questions at any time about the use, installation, or performance of your Hansgrohe product, or this warranty, please call or
write to us or call us toll-free at 800 334 0455.
27
www.hansgrohe-usa.com
US - Installation Instructions • Part No. 90111601 • Revised 01/2011
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004
Tel. 770-360-9880 • Fax 770-360-9887
Installation Instructions / Warranty
Raindance C 150
AIR 3jet
28471XX1
Technical Information
Flow rate
2.5 gpm
Installation Considerations
• For best results, Hansgrohe recommends that
this unit be installed by a licensed, professional plumber.
• Please read over these instructions thoroughly
before beginning installation. Make sure that
you have all tools and supplies needed to
complete the installation.
• To prevent scald injury, the maximum output
temperature of the shower valve must be no
higher than 120°F. In Massachusetts, the
maximum output temperature of the shower
valve can be no higher than 112°F.
• Keep this booklet and the receipt (or other
proof of date and place of purchase) for
this product in a safe place. The receipt is
required should it be necessary to request
warranty parts.
Installation
Install the showerhead on the arm.
Tighten using a 17 mm wrench.
96477000
User Instructions
Push the function lever to the desired
function.
Rain AIR
Balance AIR
Whirl AIR
function lever
Remove scale deposits from the spray channels by rubbing across them with fingers or a
sponge.
QUIC K
CLEAN
If the flow of water reduces over time,
remove the filter gasket.
1
Rinse the filter gasket with clear water and
replace.
2
Remove scale deposits from the spray face by
soaking it in a commercial scale remover such
as Lime-Away or CLR.
1
Follow the instructions on the product label.
2
Rinse the handshower with clear water.
Install the handshower and flush it for at least
one minute.
3
> 1 min.
Cleaning Recommendation for Hansgrohe Products
Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with
regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
Cleaning Materials for Faucets and Showers
Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points when
cleaning faucets and showers:
•
Only use cleaning materials which are explicitly intended for this type of application.
•
Never use cleaning materials which contain hydrochloric, formic, phosphoric, or acetic acid, as they cause considerable
damage.
•
Never mix one cleaning material with another.
•
Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads, or micro
fiber cloths.
Cleaning Instructions for Faucets and Showers
Please follow the cleaning material manufacturer’s instructions. In addition, pay attention to the following points:
•
Clean the faucets and showers as and when required
•
Use the amount of cleaning product and the amount of time recommended by the manufacturer. Do not leave the cleaner on the
fixture longer than necessary.
•
Regular cleaning can prevent calcification.
•
When using spray cleaners, spray first onto a soft cloth or sponge. Never spray directly onto the faucet as droplets can enter
openings and gaps and cause damage.
•
After cleaning, rinse thoroughly with clean water to remove any cleaner residue.
Important
Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using.
Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage.
Components with damaged surfaces must be replaced or injury could result.
Damage caused by improper treatment is not covered under the warranty.
Limited Lifetime Consumer Warranty
This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is
limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either
the United States or Canada.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original consumer purchaser only. This warranty is non-transferable.
WHAT IS COVERED BY THE WARRANTY
This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material or
workmanship as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product or part of the product
that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. If
Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made, Hansgrohe may elect to refund
the purchase price in exchange for the return of the product.
LENGTH OF WARRANTY
Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If
you are a consumer who purchased the product for use primarily for personal, family, or household purposes, this warranty extends
for as long as you own the product and the home in which the product is originally installed. If you purchased the product for use
primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with
respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products.
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR:
A. Conditions, malfunctions or damage not resulting from defects in material or workmanship.
B.
Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper maintenance,
misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no-rinse” cleaning
products, or the use of the product in any manner contrary to the product instructions. (3) Conditions in the home such as excessive water pressure or corrosion.
C. Labor or other expenses for the disconnection, deinstallation, or return of the product for warranty service, or for installation or
reinstallation of the product (including but not limited to proper packaging and shipping costs), or for installation or reinstallation
of the product.
D. Accessories, connected materials and products, or related products not manufactured by Hansgrohe.
TO OBTAIN WARRANTY PARTS OR INFORMATION
Contact your Hansgrohe retailer, or contact Technical Service at:
Hansgrohe Inc.
1492 Bluegrass Lakes Parkway
Alpharetta GA 30004
Toll-free (800) 334-0455.
In requesting warranty service, you will need to provide
1.
The sales receipt or other evidence of the date and place of purchase.
2. A description of the problem.
3. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc. 1492
Bluegrass Lakes Parkway, Alpharetta, Georgia 30004, Attention: Technical Service, if required by Hansgrohe.
When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid.
EXCLUSIONS AND LIMITATIONS
REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY
PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT.
HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL, SPECIAL, OR
CONSEQUENTIAL DAMAGES, ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY (INCLUDING
MERCHANTABILITY).
Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from State to State. You may
be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in
court against us under the Magnuson-Moss Warranty Act.
PRODUCT INSTRUCTIONS AND QUESTIONS
Upon purchase or prior to installation, please carefully inspect your Hansgrohe product for any damage or visible defect. Prior to
installing, always carefully study the enclosed instructions on the proper installation and the care and maintenance of the product. If
you have questions at any time about the use, installation, or performance of your Hansgrohe product, or this warranty, please call or
write to us or call us toll-free at 800 334 0455.
www.hansgrohe-usa.com
US - Installation Instructions • Part No. 90482121 • Revised 07/2009
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004
Tel. 770-360-9880 • Fax 770-360-9887
Installation Instructions / Warranty
Interaktiv
13412XX1
Interaktiv
06959XX1
Retroaktiv
06088XX0
Retroaktiv
06089XX0
Interaktiv Tub Spouts
Retroaktiv Tub Spouts
06888XX0
13412XX1
Requires 1/2” male threaded nipple extending
4 1/2” - 4 3/4” outside the surface of the
finished wall.
Requires 1/2” male threaded nipple extending
3” - 3 1/4” outside surface of finished wall.
06959XX1
Requires 1/2” male threaded nipple extending
5/8” outside surface of finished wall.
06089XX0
Requires 1/2” male threaded nipple extending
3” - 3 1/4” outside surface of finished wall.
Installation: 06959XX1 only
Wrap the threads on the nipple with Teflon tape. Seal the
wall around the nipple with waterproof sealant.
Screw the mounting piece to the nipple. A 12mm Allen
wrench (not included) is useful. Slide the spout over the
mounting piece. Tighten the set screw with a 3 mm Allen
wrench.
Installation: All other models
Wrap the threads on the nipple with Teflon tape. Seal the
wall around the nipple with waterproof sealant.
Screw the spout onto the nipple, taking care not to cross
thread. If a final turn by wrench is desired, use a strap
wrench.
Turn on the water, flush, and check for leaks.
User Instructions - Diverter Tub Spouts
When the water is turned on, it will flow through the spout. To divert the water to the showerhead, push the diverter knob downward. When the water is turned off, the diverter will reset to
the spout position.
Cleaning Recommendation for Hansgrohe Products
Modern sanitary faucetry and shower fixtures consist of very different materials to comply with the needs of the market
with regard to design and functionality.
To avoid damage and returns, it is necessary to consider certain points when cleaning:
Cleaning materials for faucets and shower products:
Acids are necessary ingredients of cleaning materials for removing lime. However, please pay attention to the
following points when cleaning faucets and shower products:
•
•
•
•
Use only cleaning materials intended for the application.
Never use cleaning materials which contain hydrochloric, formic, or phosphoric, or acetic acid, as these can
cause considerable damage.
Do not mix one cleaning material with another.
Do not use abrasives, such as cleaning powders, sponge pads, or microfiber cloths.
Cleaning Instructions for Faucets and Shower Products:
Please follow the cleaning material manufacturer’s instructions. In addition, please note the following:
•
•
•
•
•
Clean your faucets and shower products as and when required.
Follow the label instructions. Do not allow any cleaner to remain on the product for longer than necessary.
Regular cleaning will prevent scale buildup and water spotting.
When using spray cleaners, spray first onto a sponge or cloth. Do not spray directly onto the faucet or shower
product as drops could enter openings or gaps and cause damage.
After cleaning, rinse thoroughly with clear water to remove any cleaner residue.
Important
Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using.
Please note:
•
•
•
If the surface is already damaged, the effect of cleaning materials will cause further damage.
Components with damaged surfaces must be replaced, otherwise, this could cause injury.
Damage caused by improper treatment will not be covered by our warranty.
Limited Lifetime Consumer Warranty
This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is
limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the
United States or Canada.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original consumer purchaser only.
WHAT IS COVERED BY THE WARRANTY
This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material or
workmanship as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product or part of the product
which proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. If
Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made, Hansgrohe may elect to refund the
purchase price in exchange for the return of the product.
LENGTH OF WARRANTY
Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If you are
a consumer who purchased the product for use primarily for personal, family, or household purposes, this warranty extends for as long as
you own the product and the home in which the product is installed. If you purchased the product for use primarily for any other purpose,
including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Interaktiv and Retroaktiv
products, and (ii) for 5 years, with respect to AXOR, ShowerPower and Pharo products.
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR:
A.
Conditions, malfunctions or damage not resulting from defects in material or workmanship.
B.
Conditions, malfunctions or damage resulting from (1) improper installation, improper maintenance, misuse, abuse, negligence,
accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no rinse” cleaning products, or the use of the
product in any manner contrary to the product instructions.
C.
Labor or other expenses for the disconnection or return of the product for warranty service, or for installation or reinstallation of the
product.
D.
Accessories or related products not manufactured by Hansgrohe.
TO OBTAIN WARRANTY SERVICE
Contact your Hansgrohe retailer, or write to Technical Service at:
Hansgrohe Inc.
1492 Bluegrass Lakes Parkway
Alpharetta GA 30004
Or, call Hansgrohe toll-free at (800) 334-0455.
In requesting warranty service, you will need to provide
1.
2.
3.
The sales receipt or other evidence of the date and place of purchase.
A description of the problem.
Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc. 1492
Bluegrass Lakes Parkway, Alpharetta, Georgia 30004, Attention: Technical Service, if required by Hansgrohe.
When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid.
EXCLUSIONS AND LIMITATIONS
REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON
TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT.
HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL, SPECIAL, OR CONSEQUENTIAL
DAMAGES, ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY (INCLUDING MERCHANTABILITY).
Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from State to State.
PRODUCT INSTRUCTIONS AND QUESTIONS
Upon purchase or prior to installation, please carefully inspect your Hansgrohe product for any damage or visible defect. Prior to
installing, always carefully study the enclosed instructions on the proper installation and the care and maintenance of the product. If you
have questions at any time about the use, installation, or performance of your Hansgrohe product, or this warranty, please call or write
to us at the toll-free number and address printed above.
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004
Tel. 770 360-9880 • Fax 770 360 9887
www.hansgrohe-USA.com
US - Installation Instructions • Part No.90965201-02 • Revised 04/2007
You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any
action in court against us under the Magnuson-Moss Warranty Act.