USER MANUAL
600 // CERAMIC HOB - TOUCH
TCT61
IMPORTANT // Please ensure that you read through this user manual prior to installation and use. This manual
contains important information to ensure optimal performance and keep you safe. Please retain your proof
of purchase, as this will be required in the event that you require warranty service. Remember to retain this
manual for future reference.
tisira | www.tisira.com
www.tisira.com
pg 1
HELLO
CONGRATULATIONS ON THE SELECTION OF THIS TISIRA APPLIANCE. TISIRA
APPLIANCES HAVE BEEN SPECIFICALLY DESIGNED FOR AUSTRALIAN AND
NEW ZEALAND KITCHENS.
Please read through this user manual carefully as it contains information that
will ensure that your appliance is installed correctly, important operating & care
instructions and also some advice of what you need to do if this appliance is not
performing as intended.
pg 2
www.tisira.com | tisira
CONTEN TS
HELLO
2
CONTENTS
3
WARNING & SAFETY INFORMATION
4
PROduCT OvERvIEW
6
ELECTRICAL CONNECTION
7
INSTALLATION
8
...INSTALLATION
9
OPERATING INSTRuCTIONS
10
MAINTAINING YOuR COOkTOP
13
TROubLESHOOTING
14
PROduCT SPECIFICATIONS
14
NOTES
15
CONTACT dETAILS
16
tisira | www.tisira.com
pg 3
WARNING
& SAFETY
INFORMATION
Installation
This appliance is to be properly installed and
earthed only by a suitably qualified person.
Electrical Shock Hazard
This appliance should be connected to a circuit
which incorporates an isolating switch providing
full disconnection from the power supply.
Disconnect the appliance from the mains
electricity supply before carrying out any
work or maintenance on it.
Connection to a good earth wiring system is
essential and mandatory.
Alterations to the domestic wiring system
must only be made by a qualified electrician.
Failure to follow this advice may result in
electrical shock or death.
Operation and maintenance
Electrical Shock Hazard
Take care - panel edges are sharp.
Do not cook on a broken or cracked cooktop.
If the cooktop surface should break or crack,
switch the appliance off immediately at
the mains power supply (wall switch) and
contact a qualified technician.
Failure to use caution could result in injury
or cuts.
Switch the cooktop off at the wall before
cleaning or maintenance.
Cut Hazard
Important safety instructions
Read these instructions carefully before
installing or using this appliance.
No combustible material or products should
be placed on this appliance at any time.
Please make this information available to
the person responsible for installing the
appliance as it could reduce your installation
costs.
In order to avoid a hazard, this appliance must
be installed according to these instructions
for installation.
pg 4
Failure to install the appliance correctly could
invalidate any warranty or liability claims.
Failure to follow this advice may result in
electrical shock or death.
Health Hazard
This appliance complies with electromagnetic safety standards.
However, persons with cardiac pacemakers
or other electrical implants (such as insulin
pumps) must consult with their doctor or
implant manufacturer before using this
appliance to make sure that their implants will
not be affected by the electromagnetic field.
Failure to follow this advice may result in
death.
www.tisira.com | tisira
Hot Surface Hazard
During use, accessible parts of this appliance
will become hot enough to cause burns.
Do not let your body, clothing or any item
other than suitable cookware contact the
ceramic glass until the surface is cool.
Never leave metal objects (such as kitchen
utensils) or empty pans on the cooktop as
they can become hot very quickly.
Beware // magnetisable metal objects worn
on the body may become hot in the vicinity of
the cooktop. Gold or silver jewellery will not
be affected.
Keep children away.
Handles of saucepans may be hot to touch.
Check saucepan handles do not overhang
other cooking zones that are on. Keep
handles out of reach of children.
Failure to follow this advice could result in
burns and scalds.
Cut Hazard
The razor-sharp blade of a cooktop scraper
is exposed when the safety cover is retracted.
Use with extreme care and always store
safely and out of reach of children.
Failure to use caution could result in injury
or cuts.
Important safety instructions
Never leave the appliance unattended when
in use. Boilover causes smoking and greasy
spillovers that may ignite.
Do not place or leave any magnetisable
objects (e.g. credit cards, memory cards)
or electronic devices (e.g. computers, MP3
players) near the appliance, as they may be
affected by its electromagnetic field.
Never use your appliance as a work or
storage surface.
Never leave any objects or utensils on the
appliance.
Never use your appliance for warming or
heating the room.
tisira | www.tisira.com
After use, always turn off the cooking zones
and the cooktop as described in this manual
(i.e. by using the touch controls). Do not rely
on the pan detection feature to turn off the
cooking zones when you remove the pans.
Do not allow children to play with the
appliance or sit, stand, or climb on it.
Do not store items of interest to children in
cabinets above the appliance. Children climbing
on the cooktop could be seriously injured.
Do not leave children alone or unattended in
the area where the appliance is in use.
Children or persons with a disability which
limits their ability to use the appliance should
have a responsible and competent person
to instruct them in its use. The instructor
should be satisfied that they can use the
appliance without danger to themselves or
their surroundings.
Do not repair or replace any part of the
appliance unless specifically recommended
in the manual. All other servicing should be
done by a qualified technician.
Do not use a steam cleaner to clean your
cooktop.
Do not place or drop heavy objects on your
cooktop.
Do not stand on your cooktop.
Do not use pans with jagged edges or drag
pans across the ceramic glass surface as
this can scratch the glass.
Do not use scourers or any other harsh
abrasive cleaning agents to clean your
cooktop, as these can scratch the ceramic
glass.
If the power supply cable is damaged, it must
only be replaced by a qualified technician.
Do not operate your cooktop by means of an
external timer or separate remote-control
system.
This appliance is intended to be used in
domestic households only .
pg 5
product overview
TOP VIEW
1
2
5
6
4
1. 1200 W zone
2. 1800 W zone
3. 1200 W zone
4. 1800 W zone
5. Glass plate
6. Control panel
3
CONTROL PANEL
1. ON/OFF control
2.Keylock control
3. Power regulating controls
3
1
pg 6
2
www.tisira.com | tisira
ELECTRICAL
CONNECTION
CONNECTING THE HOB TO THE MAINS POWER SUPPLY
The power supply should be connected in compliance with the relevant standard, or a singlepole circuit breaker. The method of connection is shown below:
3
4
L1 2
Black
L2 3
Brown
Blue
4
N
380-415V~
2
220-240V~
1
220-240V~
Yellow / Green
1
The appliance can be connected directly to the mains by single-phase electric connection.
25A~
L1
2
L2
3
N
4
Yellow / Green
Black
Brown
220-240V~
220-240V~
1
.
Blue
If the cable is damaged or needs replacing, this should be done by an aftersales technician
using the proper tools, so as to avoid any accidents.
If the appliance is being connected directly to the mains supply, an omnipolar circuit
breaker must be installed with a minimum gap of 3mm between the contacts.
The installer must ensure that the correct electrical connection has been made and that
it complies with safety regulations.
The cable must not be bent or compressed.
The cable must be checked regularly and only replaced by a properly qualified person.
tisira | www.tisira.com
pg 7
Installation
Selection of installation equipment
Cut out the work surface according to the sizes shown in the drawing. For the purpose of
installation and use, a minimum of 50mm space shall be preserved around the hole.
Be sure the thickness of the work surface is at least 30mm. Please select heat resistant work
surface material to avoid deformation caused by the heat radiation from the hotplate.
L
590 W
520 HD
50 46 AB
+4
560 +1
X
+4
+1
490 50
Under all circumstances, make sure the ceramic cooker hob is well ventilated and the air
inlet and outlet are not blocked. Ensure the ceramic cooker hob is in good working state.
Notice // The safety distance between the hotplate and the cupboard above
the hotplate should be at least 760mm.
A
B
760 Min 50 C
D
Min 20 Air intake
E
Air exit 5mm
Before locating the fixing brackets
The unit should be placed on a stable, smooth surface
(use the packaging). Do not apply force onto the controls
protruding from the hob.
Fix the hob on the work surface by screw four brackets on
the bottom of hob. (see picture) after installation.
pg 8
www.tisira.com | tisira
...Installation
A
B
ScrewBracket
C
D
ScrewBase Cutout
NOTICE // Adjust the bracket position to suit for different work surface’s thickness.
BRACKET
BRACKET
Caution //
The ceramic cooker hob must be installed by qualified personnel or technicians. Please
never conduct the operation by yourself.
The ceramic cooker hob shall not be mounted to cooling equipment, dishwashers and
rotary dryers.
The wall and induced heating zone above the work surface shall withstand heat.
To avoid any damage, the sandwich layer and adhesive must be resistant to heat.
A steam cleaner is not to be used.
tisira | www.tisira.com
pg 9
OPERATING
INSTRUCTIONS
Using the Touch Controls
The controls respond to touch, so you don’t need to apply any pressure.
Use the ball of your finger, not its tip.
You will hear a beep each time a touch is registered.
Make sure the controls are always clean, dry, and that there is
no object (e.g. a utensil or a cloth) covering them. Even a thin
film of water may make the controls difficult to operate.
Using your Ceramic Hob
1. Touch the ON/OFF control.
After power on, the buzzer beeps once, all the indicators light up for 1
second then go out, indicating that the ceramic hob has entered the state
of standby mode.
2. Place a suitable pan on the cooking zone that you wish to use.
Make sure the bottom of the pan and the surface of the cooking zone are
clean and dry.
3. Select a heat setting by touching the
or
control.
If you don’t choose a heat setting within 1 minute, the ceramic hob will
automatically switch off. You will need to start again at step 1.
You can modify the heat setting at any time during cooking.
-
5
+
When you have finished cooking
1. Turn the cooking zone off by scrolling down to
pg 10
or touching and control together.
OR
-
-
-
-
-
-
or
www.tisira.com | tisira
2. Turn the whole cooktop off by touching the ON/OFF control.
3. Beware of hot surfaces
“H” will show which cooking zone is hot to touch. It will disappear when
the surface has cooled down to a safe temperature. It can also be used as
an energy saving function if you want to heat further pans, use the hotplate
that is still hot.
Locking the Controls
You can lock the controls to prevent unintended use (for example children
accidentally turning the cooking zones on). When the controls are locked,
all the controls except the ON/OFF control are disabled.
To lock the controls:
Touch the keylock control. The indicator next to the keylock will light up.
To unlock the controls:
1. Make sure the ceramic hob is turned on.
2. Touch and hold the keylock control for a while.
3. You can now start using your ceramic hob.
NOTICE // When the hob is in the lock mode, all the controls are disabled except the ON/OFF.
You can always turn the ceramic hob off with the ON/OFF control in an emergency, but you
shall unlock the hob first in the next operation.
Over-Temperature Protection
A temperature sensor monitors the temperature inside the ceramic hob. When an excessive
temperature is monitored, the ceramic hob will stop operation automatically.
Residual Heat Warning
When the hob has been operating for some time, there will be some residual heat. The letter
“H” appears to warn you to keep away from it.
Auto Shutdown
Another safety feature of the hob is auto shutdown. This occurs whenever you forget to switch
off a cooking zone. The default shutdown times are shown in the table below:
Power level 1
Default working timer (hour) 8
tisira | www.tisira.com
2
8
3
8
4
4
5
4
6 7
4 2
8
2
9
2
pg 11
Heating Settings
The settings below are guidelines only. The exact setting will depend on several factors,
including your cookware and the amount you are cooking. Experiment with the cooktop to
find the settings that best suit you.
Heat setting
Suitability
1-2
• delicate warming for small amounts of food
• melting chocolate, butter, and foods that burn quickly
• gentle simmering
• slow warming
3-4
• reheating
• rapid simmering
• cooking rice
5-6
• pancakes
7-8
• sautéing
• cooking pasta
9
• stir-frying
• searing
• bringing soup to the boil
• boiling water
Choosing the right Cookware
Do not use cookware with jagged edges or a curved
base.
Always lift pans off the ceramic
hob – do not slide, or they may
scratch the glass.
Make sure that the base of your pan is smooth, sits flat
against the glass, and is the same size as the cooking
zone. Always centre your pan on the cooking zone.
pg 12
www.tisira.com | tisira
Maintaining
your cooktop
Cleaning & Care
ISSUE?
SOLUTION
IMPORTANT
Everyday soiling on glass
(fingerprints, marks, stains left
by food or non-sugary spillovers
on the glass)
1. Switch the power to the
cooktop off.
2. Apply a cooktop cleaner while
the glass is still warm (but not
hot!)
3. Rinse and wipe dry with a
clean cloth or paper towel.
4. Switch the power to the
cooktop back on.
• When the power to the cooktop
is switched off, there will be no
‘hot surface’ indication but the
cooking zone may still be hot!
Take extreme care.
• Heavy-duty scourers, some nylon
scourers and harsh/abrasive
cleaning agents may scratch the
glass. Always read the label to
check if your cleaner or scourer
is suitable.
• Never leave cleaning residue
on the cooktop: the glass may
become stained.
Boilovers, melts, and hot sugary
spills on the glass
Remove these immediately with
a fish slice, palette knife or razor
blade scraper suitable for ceramic
glass cooktops, but beware of hot
cooking zone surfaces:
1. Switch the power to the cooktop
off at the wall.
2. Hold the blade or utensil at a 30°
angle and scrape the soiling or
spill to a cool area of the cooktop.
3. Clean the soiling or spill up with
a dish cloth or paper towel.
4. Follow steps 2 to 4 for ‘Everyday
soiling on glass’ above.
• Remove stains left by melts and
sugary food or spillovers as soon
as possible. If left to cool on the
glass, they may be difficult to
remove or even permanently
damage the glass surface.
• Cut hazard: when the safety
cover is retracted, the blade in
a scraper is razor-sharp. Use
with extreme care and always
store safely and out of reach of
children.
Spillovers on the touch controls
1. Switch the power to the
cooktop off.
2. Soak up the spill
3. Wipe the touch control area with
a clean damp sponge or cloth.
4. Wipe the area completely dry
with a paper towel.
5. Switch the power to the
cooktop back on.
• The cooktop may beep and turn
itself off, and the touch controls
may not function while there
is liquid on them. Make sure
you wipe the touch control area
dry before turning the cooktop
back on.
tisira | www.tisira.com
pg 13
TROUBLESHOOTING
PROBLEM
pg 14
POSSIBLE CAUSES
WHAT TO DO
The cooktop cannot be turned
on.
No power.
• Make sure the cooktop is
connected to the power supply
and that it is switched on.
• Check whether there is a power
outage in your home or area.
If you’ve checked everything
and the problem persists, call a
qualified technician.
The touch controls are
unresponsive.
The controls are locked.
unlock the controls. See section
‘using your induction cooktop’
for instructions.
The touch controls are difficult
to operate.
There may be a slight film
of water over the controls or
you may be using the tip of
your finger when touching the
controls.
Make sure the touch control
area is dry and use the ball of
your finger when touching the
controls.
The glass is being scratched.
Rough-edged cookware.
unsuitable, abrasive scourer or
cleaning products being used.
use cookware with flat and
smooth bases. See ‘Choosing
the right cookware’.
Some pans make crackling or
clicking noises.
This may be caused by the
construction of your cookware
(layers of different metals
vibrating differently).
This is normal for cookware and
does not indicate a fault.
www.tisira.com | tisira
NOTES
tisira | www.tisira.com
pg 15
VERSION 3.1
Download PDF
Similar pages