INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com  website: www.hawsco.com
No. 2076304(18)
Model 1001/1001HPS
Drinking Fountain
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
LIMITED WARRANTY
HAWS warrants that this specific product is guaranteed against defective material or
poor workmanship for a period of one year from date of shipment. HAWS liability
under this warranty shall be discharged by furnishing without charge F.O.B. HAWS
Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided that
claim is made in writing to Haws within a reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS,
Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer
agrees that HAWS shall not be liable for general, special, or consequential damages
claimed to arise under the contract of sale. The drinking fountain manufactured by
HAWS is warranted to function if installation and maintenance instructions provided
are adhered to. The units also must be used for the purpose for which they were
intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT:
1-800-766-5612
FOR CUSTOMER SERVICE:
1-888-640-4297
03/17
Model 1001/1001HPS
Page 1 of 5
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12" adjustable
wrench, 10" pipe wrench, 3/32” and 5/32” hex key wrench, 9/16”, 1/2", 7/16” socket wrench
or open end wrench.
LOCATION OF UNIT: The Model 1001/1001HPS Drinking Fountain is a wheelchair
accessible drinking water facility. The height dimensions shown, meet current ADA
requirements. When installing this unit, local, state or federal codes should be adhered to. If
height other than shown is required, then dimensions must be adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 PSI (2-6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Inlet is 3/8” O.D. push-in type fitting. Waste outlet is
1-1/4” O.D. tube.
MAINTENANCE: Periodically clean the strainer. Refer to 5874 Series Valve Manual for
more information.
GENERAL NOTES:
1. For all plastic push-in type fitting connections, only connect NSF-61 copper or
plastic tubing. Stainless steel or glass tubing is not recommended. The
following assembly instructions must be followed to ensure a watertight
connection:
a.
b.
c.
d.
Cut tubing square and clean.
Mark from end of tube the length of insertion (See table below).
Push tube into the fitting until it bottoms out.
To remove, depress collet and pull tubing out.
Tube Sizes
O.D.
Tolerance
Insertion Depth
1/4”
±.005”
11/16”
3/8”
±.005”
3/4”
1/2”
±.005”
7/8”
CLEANING INSTRUCTIONS FOR HI-POLISHED STAINLESS PRODUCTS
Haws recommended cleaning procedure for hi-polished stainless products is as follows:
Use a mild detergent or soap and water for removing stains and fingerprints or use a clean cloth
with window cleaner.
03/17
Model 1001/1001HPS
Page 2 of 5
TROUBLESHOOTING
PROBLEM
1.
Insufficient bubbler flow.
REPAIR CHECKLIST
1a.
Check that inlet screwdriver stop valve is in wideopen position.
b.
Verify minimum 30 psi flowing supply pressure.
c.
Clean strainer. See 5874 Series Valve Manual.
d.
Adjust valve to increase flow. Use front adjust screw
or see 5874 Series Valve Manual.
e.
Clean screens (inside nozzle body). Unscrew
nozzle insert and very gently activate water supply
to pop out qty. 3 screens (be careful not to lose
screens). Remove any debris clogging the screen
openings and place back into nozzle body.
Reassemble nozzle insert.
For more information about Haws products, see our website: www.hawsco.com
© 2017 Haws® Corporation – All Rights Reserved
HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation.
03/17
Model 1001/1001HPS
Page 3 of 5
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
DESCRIPTION
ITEM
NOTES:
1 5874PBF (ITEM 2) INCLUDES VRK5874 CARTRIDGE
ASSEMBLY (ITEM 3) AND PBA6 FLANGED PUSH
BUTTON (ITEM 4).
*
*
1
*
1001
1001HPS
1
BUBBLER HEAD, PCP
5705
5705
2
BUTTON, PUSH, PCP, FLANGED W/ VALVE
5874PBF
5874PBF
3
VALVE REPAIR KIT
VRK5874
VRK5874
4
BUTTON, PUSH, 5874, FLANGED
PBA6
PBA6
5
PANEL, BACK, F/ SATIN SWIRL OR HI-POL SS
BP6
BP6HPS
6
PLATE, MOUNTING
6700
6700
7
STRAINER, WASTE ASSEMBLY, SCP OR PCP
6463
6463PCP
8
PANEL, ACCESS, SS SATIN OR HI-POL
6603
6603HPS
9
PLATE, BOTTOM, F/ 1000
PBM1000
PBM1000
10
INSERT, LAMINAR FLOW, 5705
0002850230 0002850230
DRIVER, NOZZLE, .25 HEX
0002082253 0002082253
11
* DENOTES OPTIONAL PART.
A
(NOT SUPPLIED)
1
3
1
4
2
1
5
6
7
9
8
11
10
(TUBING CONNECTS TO
INSERT ASSY)
DETAIL A
PARTS BREAKDOWN
(ROTATED 90° INTO VIEW)
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
ECN NO. REVISED PER BY
.
ECN: 5124 VWC
CHKD
DATE
DRAWN
RTM
10/19/98 VWC
DATE
APPROVED
FV
07/06/17
PART NUMBER
MODEL(S)
SCALE:
1:1
DRAWING TYPE:
PARTS BREAKDOWN
2017 Haws Corporation - All Rights Reserved
HAWS R and other trademarks used in these materials are the exclusive property of Haws Corporation.
C
0002076304
1001/1001HPS
DIRNKING FOUNTAIN
REVISION
18
SIZE: A
SHEET 1 OF
PAGE 4 OF 5
1
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
NOTES:
HOLD ROUGH-IN DIMENSIONS ±1/8" (3.2mm).
2.
WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL
CODES SHOULD BE ADHERED TO FOR INSTALLATION
DIMENSIONS (LOCATIONS), WASTE AND SUPPLY REQUIREMENTS
OTHER THAN SHOWN.
MOUNTING BOLTS
(NOT SUPPLIED)
A
16"
[406]
ø14 1/8"
[359]
3 INSTALLER MUST PROVIDE TRAP FOR PROPER INSTALLATION.
PAGE 5 OF 5
1.
4 REMOVE VALVE FROM PUSH BUTTON TO INSTALL WASTE
ELBOW ONTO BOWL. AFTER WASTE ELBOW IS INSTALLED,
REINSTALL VALVE AND ADJUST FLOW.
1 27/32"
[47]
3 1/4"
[83]
5 REFER TO 5874 SERIES OPERATION AND MAINTENANCE MANUAL
FOR PUSH BUTTON AND VALVE INSTALLATION/MAINTENANCE
INSTRUCTIONS.
A
WASTE BEND AND
1-1/4" IPS TRAP
(NOT SUPPLIED)
WALL FACE
3"
[76]
5 1/4"
[133]
SECTION A-A
ROTATED 90° INTO VIEW
BRACKET MOUNTING
DETAIL
WALL STUD
3
1 1/4" OD
WASTE BEND
(SUPPLIED)
4
DETAIL C
BACK PANEL (OPTIONAL):
1001 & 1001HPS
15"
[380]
3"
[76]
18 5/8"
[473]
3"
[76]
6700 MOUNTING PLATE
(BEHIND FINISH WALL)
Ø3/8" SUPPLY TUBING
AND SCREW DRIVER STOP
(NOT SUPPLIED)
5
4X 3/8-16 UNC
1 27/32"
[47]
7"
[178]
2"
[51]
5"
[127]
34"
[864]
(TO SPOUT
OUTLET)
25 3/8"
[645]
C
27"
[686]
28 3/32"
[714]
WASTE
WALL FACE
FLOOR LINE
1"
[25]
2 9/32"
[58]
16"
[406]
28 11/16"
[729]
SUPPLY
18"
[457]
6700 MOUNTING PLATE
MUST BE INSTALLED BEFORE
FINISH WORK. THIS PLATE IS A
STANDARD ITEM.
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
OPTIONAL TRAP ACCESS PANEL
MODELS 6603 AND 6603HPS
ECN NO. REVISED PER BY:
MODEL(S)
.
ECN: 5124 VWC
CHK'D.:
DATE:
DRAWN:
RTM
05/97
VWC
DATE:
APPROVED:
FV
07/06/17
1:1
SCALE:
C
4X ø3/8"
[10]
R
PART NUMBER
0002076304.D
1001/1001HPS
DRINKING FOUNTAIN
DRAWING TYPE:
INSTALLATION
REVISION
18
SIZE: A
2017 Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
SHEET 1 OF
1
Download PDF
Similar pages