WAREWASHING
Utensil washer
PROFI UXTH
UXTH-10A
UXTLH-10A
UXTLHB-10A
DSN: UX-15-01
From SN: 86 64 10001
Installation and
Operation Instructions
(Translation of the original operating
instructions)
5. Oct. 2015
EN
EN
PROFI UXTH
Installation and Operation Instructions
Publisher
HOBART GmbH
Robert-Bosch-Str. 17
77656 Offenburg
Tel. +49(0)781 600 0
Fax +49(0)781 600 23 19
E-mail: info@hobart.de
Internet: www.hobart.de
Product disclaimer
Installations and repairs carried out by non-authorized technicians or using non-genuine spare parts, and any technical alterations to the machine not approved by the manufacturer will invalidate the manufacturer’s warranty and
product liability.
HOBART reserves the right to make changes or improvements to its products without prior notice.
© HOBART GmbH, Offenburg 2015
2
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
Installation and Operation Instructions
PROFI UXTH
Table of Contents
Table of Contents
1
Notes on the documentation�������������������������������������������������������������� 5
1.1Application������������������������������������������������������������������������������������� 5
1.2
Layout of the documentation��������������������������������������������������������������������� 5
1.3
Representation convention����������������������������������������������������������������������� 5
2
Safety instructions and regulations������������������������������������������������������ 7
2.1
Safety instructions and warning notices����������������������������������������������������������� 7
2.2
Basic safety instructions������������������������������������������������������������������������� 7
2.3
Property damage�������������������������������������������������������������������������������� 9
3
Product description����������������������������������������������������������������������� 10
3.1
Intended purpose������������������������������������������������������������������������������ 10
3.2Conformity������������������������������������������������������������������������������������ 10
3.3Designation������������������������������������������������������������������������������������ 10
3.4
Technical specifications������������������������������������������������������������������������� 10
4Controls������������������������������������������������������������������������������������ 11
4.1Controls��������������������������������������������������������������������������������������� 11
4.2
Operating states������������������������������������������������������������������������������� 12
4.3
Display of faults and information����������������������������������������������������������������� 13
4.4
Display function�������������������������������������������������������������������������������� 13
4.5
Overview of main menus������������������������������������������������������������������������ 14
4.6
Overview of display symbols�������������������������������������������������������������������� 14
5Installation��������������������������������������������������������������������������������� 16
5.1
Personnel qualification�������������������������������������������������������������������������� 16
5.2
Special safety instructions���������������������������������������������������������������������� 16
5.3
Transporting to the installation location����������������������������������������������������������� 17
5.4
Removing the packaging������������������������������������������������������������������������ 17
5.5
Installing the machine�������������������������������������������������������������������������� 17
5.6
Connecting to the power supply����������������������������������������������������������������� 18
5.7
Connecting the water��������������������������������������������������������������������������� 19
5.8
Connect steam (optional)����������������������������������������������������������������������� 19
5.9
Connecting the drain��������������������������������������������������������������������������� 20
5.10
Connecting the dispenser����������������������������������������������������������������������� 20
6Commissioning���������������������������������������������������������������������������� 23
6.1
Personnel qualification�������������������������������������������������������������������������� 23
6.2
Starting the commissioning procedure����������������������������������������������������������� 23
6.3
Setting the language��������������������������������������������������������������������������� 23
6.4
Setting the date�������������������������������������������������������������������������������� 23
6.5
Setting the time�������������������������������������������������������������������������������� 23
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
3
EN
EN
PROFI UXTH
Installation and Operation Instructions
Table of Contents
6.6
Filling chemical hoses�������������������������������������������������������������������������� 24
6.7
Completing the commissioning procedure�������������������������������������������������������� 25
6.8
Starting up the chemical deficiency sensor system������������������������������������������������ 25
7Operation����������������������������������������������������������������������������������� 26
7.1
Personnel qualification�������������������������������������������������������������������������� 26
7.2
Special safety instructions���������������������������������������������������������������������� 26
7.3
Preparations for washing����������������������������������������������������������������������� 27
7.4
Displaying and selecting the program������������������������������������������������������������ 28
7.5Washing��������������������������������������������������������������������������������������� 29
7.6
Special features in operation with hood lift (optional)����������������������������������������������� 29
7.7
Switch off machine����������������������������������������������������������������������������� 30
7.8
Executing daily cleaning������������������������������������������������������������������������ 31
7.9
Executing weekly cleaning���������������������������������������������������������������������� 31
7.10
Executing hygiene cleaning��������������������������������������������������������������������� 32
7.11
Changing the chemical product������������������������������������������������������������������ 32
7.12
Displaying the temperatures��������������������������������������������������������������������� 33
8
Setting options, operating and hygiene data������������������������������������������ 34
8.1
Overview of operator menu��������������������������������������������������������������������� 34
8.2
Opening the operator menu��������������������������������������������������������������������� 35
8.3
Navigating, selecting and setting within the menu������������������������������������������������� 35
8.4
Exiting the operator menu����������������������������������������������������������������������� 36
8.5
Making the general settings��������������������������������������������������������������������� 36
8.6
Setting the display indications������������������������������������������������������������������� 36
8.7
Setting the acoustic signal���������������������������������������������������������������������� 37
8.8
Making the chemical settings�������������������������������������������������������������������� 37
8.9
Configuring the counter for external water treatment (optional)������������������������������������� 38
8.10
Displaying the operating/hygiene data������������������������������������������������������������ 38
8.11
Setting automatic switch-on��������������������������������������������������������������������� 40
9
Fault indications and problems��������������������������������������������������������� 42
9.1
Fault indications������������������������������������������������������������������������������� 42
9.2
Remedying the problem������������������������������������������������������������������������ 44
10Maintenance������������������������������������������������������������������������������� 46
11Disposal������������������������������������������������������������������������������������ 47
4
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Notes on the documentation
1
Notes on the documentation
1.1
Application
This document contains the most important information for the
installation and commissioning of the machine by qualified personnel, as well as the information required for day-to-day operation by
the operator.
►► Keep the operating instructions and all referenced documents in
a safe and accessible place.
►► If you sell the machine, pass on the installation and operating
instructions.
1.2
Layout of the documentation
Referenced documents are all instructions that describe the installation, operation, maintenance and repair of the device, as well as
additional instructions for all accessories used.
For the operator:
–– Comic Card (brief instructions)
–– Operating instructions
For the specialised tradesman:
–– Installation instructions
–– Service Manual
–– Service Software Manual
–– Trouble shooting list
–– Circuit diagram
–– Spare parts catalogue
1.3
Representation convention
1.3.1
Symbols used
Symbol
Meaning
Warning of hazardous electrical voltage
Beware of explosion
EX
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
5
EN
EN
PROFI UXTH
Installation and Operation Instructions
Notes on the documentation
Symbol
Meaning
Warning of risk of crushing
Beware of hazardous substances
Beware of hand injuries
Beware of slipping
Beware of hazard area
Useful additional information and tips
1.3.2
Representation in the text
Representation
Meaning
NOTE
Important information on machine operation, not
a warning notice
►
Step
Outcome/result
6
‒
Listing 1st level
•
Listing 2nd level
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Safety instructions and regulations
2
Safety instructions and regulations
2.1
Safety instructions and warning notices
►► During machine operation, observe the general safety instructions and warning notices that precede each action.
2.1.1
Hazard levels
The hazard level is part of the safety instructions and is denoted by
the signal word. Potential consequences are differentiated by the
choice of signal word.
DANGER
imminent danger:
results in serious physical injury or death
WARNING
potentially hazardous situation:
can cause serious physical injury or death
CAUTION
potentially hazardous situation:
can cause minor physical injury
potentially harmful situation:
can cause damage to the product or other objects
NOTICE
2.1.2
Layout of warning notices
Warning notices are depicted with warning symbols and signal
word in the corresponding safety colours.
!
CAUTION
Nature and source of the hazard
Explanation on the nature and source of the hazard
►► Measures for averting the hazard
►► additional measures for averting the hazard, where applicable
2.2
Basic safety instructions
2.2.1
Product safety
The machine conforms to state-of-the-art technology and the recognised safety regulations. Nonetheless, hazards may occur.
Operate the machine only if it is in perfect working order, and in
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
7
EN
EN
PROFI UXTH
Installation and Operation Instructions
Safety instructions and regulations
compliance with the operating instructions.
All modifications and alterations to the product are reserved for
persons authorised by HOBART. Configuration is password-protected.
2.2.2
Personnel qualification
►► Observe the regulations on occupational health and safety.
►► Carefully read through the operating instructions before use.
Activity
User group
Qualification/training
Installation/Commissioning
Qualified personnel
Authorised electrician (qualified electrician or persons who
have undergone equivalent training)
Trainees
Only under appropriate supervision and inspection
Work on the electrical Qualified personnel
system
Qualified electrician
Operation
Laymen/disabled persons
Training by the operator using the operating instructions,
hazard briefing
Children from 14 years
old
Training by the operator using the operating instructions, hazard briefing, only under supervision
Children up to 13 years
old
Not permitted
Qualified personnel
Hobart Service or Hobart trained service technicians
Trainees
Only under appropriate supervision and inspection
Maintenance, repair
2.2.3
Product-specific hazards
Avoid body parts being crushed or knocked:
►► Observe the instructions on the packaging for storage, lifting or
transporting.
Avoid risk of explosion:
►► Do not install machine in a potentially-explosive location.
Avoid electric shock, fire hazard:
►► Do not allow water to flow over live components.
–– Make sure the machine is correctly stored (see frost damage
section 2.3).
–– Make sure that the machine does not overflow when being
filled.
►► Do not damage the connection cable while unpacking.
►► Have the machine connected to the power supply by qualified
personnel.
►► Have all modifications to the machine carried out by qualified
personnel.
►► Have additional feed tanks mounted by qualified personnel.
8
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Safety instructions and regulations
►► Do not operate the machine without supervision.
Avoid chemical burns, sensitisation of the skin, poisoning:
►► Wear protective equipment (gloves, safety goggles, protective
clothing) when handling chemicals.
►► Use only suitable chemicals. Observe the manufacturer’s data.
►► Have chemical sensor system set by authorised trained service
technicians.
►► Do not open the machine during operation, wait for the program
to finish.
►► Disconnect the machine from the mains prior to cleaning.
►► Wear protective equipment (gloves, safety goggles, protective
clothing) when cleaning parts contaminated by washing solution.
Avoid burns, scalds (to the hands):
►► Do not open the machine during operation or the evaporation
phase, wait for the program to finish.
►► Disconnect the machine from the mains prior to cleaning.
Avoid slipping:
99 Moisture can build up on the machine floor.
►► Provide a floor covering that is guaranteed to be non-slip in
case of moisture.
2.2.4
Additional hazards
Potential hazards caused by operating resources to be used can
be found in the enclosed safety datasheets. Workplaces must be
signed accordingly.
2.3
Property damage
Avoid frost damage:
99 Temperatures below 0°C during transport/storage cause function impairments.
►► Prior to installation, store the machine at room temperature
(min. 15°C) for 24h.
Avoid water damage:
►► Do not operate the machine without supervision.
►► Close on-site shut-off valves at the end of operation.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
9
EN
EN
PROFI UXTH
Installation and Operation Instructions
Product description
3
Product description
3.1
Intended purpose
The machine is an item of technical equipment intended solely for
commercial dishwashing.
The machine is designed solely for cleaning crockery (porcelain,
glass, ceramic, temperature-resistant plastics or stainless steel or
similar) from the food industry.
Not for washing:
–– Containers that do not come into contact with foodstuffs, such
as ashtrays, candlesticks, electric appliances etc.
–– Animals or textiles
–– Foodstuffs intended for further consumption
3.2
Conformity
See separate EC Conformity Declaration.
3.3
Designation
The rating plate is located on the front of the machine. If you have
any questions regarding service and parts, quote the serial and
DSN No.
3.4
Technical specifications
UXTH
UXTHL
Dimensions (H x W x D)
1,732 x 1,447 x 936 mm
1,984 x 1,447 x 936 mm
Water consumption per rack
8 to 10.5 l, depending on level of soil
Flow pressure
0.5 – 10 bar
Cold or hot water connection
max. 60°C
Voltage
see rating plate
Total connected load
Fuse protection
Tank capacity
130 l
Rack height
620 mm
Emission sound pressure level LpA
68 dB (A)
(Measurement uncertainty KpA= 2.5 dB)
Weight
364 kg
10
IO-0000000199-001-EN / 5. Oct. 2015
880 mm
415 kg
HOBART
PROFI UXTH
Installation and Operation Instructions
Controls
4
Controls
4.1
2
Controls
1
3
60s
Short
90s
Standard
6
5
120s Intensive
4

ON/OFF button
Pressing this button switches the machine on.
As soon as the machine is ready for operation, the wash programme can be
started by pushing this button.
Pushing and holding (3 seconds) the button activates the automatic drain
and self-cleaning cycle and switches off the machine automatically. After
switch off, however, the machine is not voltage free!
For machines with hood lift, the hood can also be opened and closed using
this button.
The button also shows the current operating state through different colours
(see sections 4.2 and 4.3 )
‚
STOP button
In case of operating error or faults, the machine can be switched off immediately without the drain cycle by pressing this key.
After switch off, however, the machine is not voltage free!
ƒ
Display
Selection menu / fault and information displays
„
Display navigation button
Scroll / set / select
…
Display navigation button
Change menu level / confirm / back/acknowledge fault
†
Display navigation button
Scroll / set / select
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
11
EN
EN
PROFI UXTH
Installation and Operation Instructions
Controls
4.1.1
HOOD LIFT button (optional)
HOOD LIFT button:
–– Pressing this button opens or closes the hood.
X
4.2
Operating states
In the operating panel display, the ON/OFF switch shows the current operating state through different colours.
Machine is Off
The ON/OFF button is colourless.
Machine being prepared for operation
The ON/OFF button gradually goes green. The wash tank is being filled and the machine is heating up.
Machine ready
–– The ON/OFF button illuminates completely green.
–– The machine is ready for the next wash cycle.
Wash program starts
–– The ON/OFF button illuminates completely blue.
Machine is washing
–– The ON/OFF button changes segment-by-segment from blue
back to completely green.
Switch off machine
–– The ON/OFF button changes segment-by-segment from green
to colourless.
–– The machine is being emptied and switched off.
12
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Controls
4.3
Display of faults and information
Fault: operation not possible
–– The ON/OFF button illuminates permanently red.
–– The fault is displayed.
–– For potential faults, see section 9.1
Information: limited operation is possible
–– The ON/OFF button illuminates green/red alternately.
–– The information is displayed.
–– For potential information, see section 9.1
4.4
Display function
The display is activated (when the machine is turned on) by pushing the display navigation buttons or moving your hand near to the
display.
On activation, the wash program selection appears first. The selected program or function is highlighted.
The function of the display navigation buttons is context-dependent
and shown in the display by symbols.
Further displays/menu levels can be selected using the … button.If
no button is pushed, the display de-activates again after 10s.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
13
EN
EN
PROFI UXTH
Installation and Operation Instructions
Controls
4.5
Overview of main menus
Program selection and info:
60s Short
–– Selects possible wash programs (depends on model variants)
90s Standard
–– The … ("i”) button accesses the Login/Temperatures/Info
menu
120s Intensive
Login/Temperatures/Info:
–– Login: Operator code accesses Operator menu
login
–– Temperatures: Displays tank and rinse temperatures.
temperatures
–– Info/maintanance: Accesses the Info/Service menu
info/maintena...
Operator menu:
general settin...
–– Gen. settings: Accesses the machine settings
display indica...
–– Display indications: Accesses display settings
–– Acoustic signal: Accesses the signal sensor setting
acoustic signal
–– ... see also section 8.1.
Info/Service:
machine type
–– Machine type: Indicates machine type and serial number.
operating data
–– Operating data: Displays operating data (see section 8.10).
–– Maintanance: Displays service address.
maintenance
4.6
Overview of display symbols
4.6.1
Wash cycle symbols
As an alternative to the text display, it is possible to switch to the
symbol display (see section 8.6).
Symbol
Program
Short
Standard
Intensive
Continuous
Hygiene
14
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Controls
4.6.2
Function symbols
Symbol
Function
Scroll menu
Accept value
Alter value
Info/Service
Login
back
Temperatures
Wash/rinse temperatures
Sound on/sound off
Timer
Salt deficiency
Chemical deficiency
Fault
Fill fault
Drain fault
Heating element fault
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
15
EN
EN
PROFI UXTH
Installation and Operation Instructions
Installation
5
Installation
5.1
Personnel qualification
Installation must only be carried out by qualified personnel (see
section 2.2.2).
5.2
Special safety instructions
!
WARNING
Risk of electric shock, fire hazard
Water (frost damage, machine overflow) flowing over live components can cause injury from electric shock or fire.
►► Do not allow water to flow under live components.
►► Make sure the machine is correctly stored (see frost damage
section 2.3).
►► Make sure that the machine does not overflow when being
filled.
!
CAUTION
Risk of being crushed or knocked
When being lifted or transported, the machine can overturn or fall
and cause injury.
►► Observe the instructions on the packaging for storage, lifting or
transporting.
!
EX
WARNING
Risk of explosion
Installing the machine in a potentially explosive location can cause
explosion and serious injury from ejected parts.
►► Do not install machine in a potentially-explosive location.
NOTICE
Frost damage
Temperatures below 0°C during transport/storage cause function
impairments.
►► Prior to installation, store the machine at room temperature
(min. 15°C) for 24h.
16
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Installation
5.3
Transporting to the installation location
►► Where possible transport packed on the pallet.
►► Use suitable transport means (elevating truck, crane etc.).
►► If using a forklift, shim the machine with wooden trusses.
5.4
Removing the packaging
!
CAUTION
Risk of electric shock, fire hazard
When the machine is unpacked, the connection cable can become
damaged and cause injury from electric shock or fire.
►► Do not damage the connection cable while unpacking the machine.
►► Take cable measurement BGV A3.
►► Remove packaging materials and accessories from the machine.
►► Inspect the machine for possible transport damage.
5.5
Installing the machine
Wall clearance at the rear is not required.
►► Maintain wall clearance of 400 mm on at least one side of the
machine.
►► Align machine by turning the adjusting feet according to the
spirit level.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
17
EN
EN
PROFI UXTH
Installation and Operation Instructions
Installation
5.6
Connecting to the power supply
!
WARNING
Risk of electric shock
Failure to connect properly to the power supply can cause mortal
danger from electric shock.
►► Have the machine connected to the power supply by an authorized technician according to the local and national codes. For
Australia: in accordance with AS/NZS3500.1
NOTE: To guarantee the electrical safety of the machine, it
must be connected to a protective earthing equipment conductor installed as specified.In addition, the machine must be
attached on site to the equipotential bonding connection. The
connecting screw ( ) provided for this purpose is located at
the rear of the floor pan next to the cable bushing.
These fundamental safety requirements and the professional
design of the on-site building installation must be verified by a
qualified electrician.
Hobart does not accept any liability for damage caused by
improper installation!Any applicable site local installation
instructions must be observed!
The mains cable must be connected via a cut-out device (main
switch or accessible plug device).
The power supply must be consistent with the data on the rating
plate.
►► Modification to an alternative power supply is possible as per
the variants on the circuit diagram.
►► Fuses and cable cross section must be designed accordingly.
To verify the correct three-phase current connection, the rotating
direction of the wash pump(s) must be checked.
►► Push a cable tie - approx. 3 cm deep - through the rear ventilation grille.
►► Check whether the fan impeller rotates counter-clockwise (in
the direction of the arrow).
►► If not, interchange two of the three phase on the feed cable.
18
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Installation
5.7
A
Connecting the water
NOTE: The machine must be operated with potable water.
►► If possible, connect to warm water (max. 60 °C).
►► Machines with drain heat recovery: If possible, connect to cold
water (approx. 10 °C).
Water hardness:
–– max. 3 °d = 0.53 mmol/l
Flow pressure:
–– 0.5 – 10 bar
–– If the flow pressure is above 10 bar: provide pressure reducing
valve.
►► Connect the union nut “A” (3/4” thread) of the water supply hose
to the site shut off valve.
►► Do not kink or cut the water supply hose.
►► Any required extension must be executed using a suitable pressure hose, e.g. 324088-1.
5.8
Connect steam (optional)
NOTE: On site, make sure that the permissible pressures and
temperatures cannot be exceeded.
i
The fittings required for operation are built into the
machine.
►► Connect to the site steam line.
–– DN 20 pipe
–– Flow pressure: 0.5 - 3.5 bar
–– Temperature: max. 150°C
–– See rating plate!
►► Dimension steam and condensate line accordingly.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
19
EN
PROFI UXTH
Installation and Operation Instructions
Installation
5.8.1
Adjustment of manual shut-off valve
The built-in manual shut-off valve is equipped with and adjustment
device to limit the flow rate of the heating supply medium. The correct adjustment is very important, particularly for higher pressures.
NOTICE
Property damage
If the valve is opened too far, pressure shocks may occur when the
solenoid valve closes.
If the valve is closed too far, the required heating power cannot be
achieved.
►► Have the adjustment made only by a HOBART-trained customer service engineer when commissioning or when the site
system is modified.
Adjustment of manual shut-off valve:
## Special wrench required
►► Adjust the valve seat so that when the valve is fully opened,
the set temperature of the booster is maintained in continuous
operation.
5.9
max. 800 mm
EN
Connecting the drain
The connection between machine and site drain must not exceed
the max. height of 0.8 m.
►► Do not kink or lay the drain hose loose on the ground.
30°-45°
5.10 Connecting the dispenser
As a rule, all model variants are already factory-equipped with
integrated dispensers. To convert to different dispensers, make the
connection as follows.
►► Drain tank.
►► Turn off the site main switch or remove the plug.
►► Remove frontal covering.
20
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Installation
To connect liquid dispensers:
►► A metering nipple is fitted at the top on the boiler for dispensing
rinse aid.
►► For detergent dosing, connect the hose (PVC / Ø 6 mm outside
× Ø 4 mm inside) between the pressure side of the dispenser
and the metering nipple (A) on the wash tank, secure with hose
clamp.
►► Install dispensers or mount externally.
To connect a powder or solid detergent dispenser:
►► Remove covering.
►► Drill out the inner tank wall according to the required connection
diameter.
►► Screw the dosing connection tightly to the tank wall.
►► Connect the plug of the cable harness to the dispenser (max.
100 VA).
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
21
EN
EN
PROFI UXTH
Installation and Operation Instructions
Installation
Installing the connectivity probe:
►► Conductivity probe should be installed at the flat part of tank
bottom.
►► Drill out the tank according to the probe diameter.
►► Replace cover(s).
►► Turn on site main switch or insert the plug.
►► Set the dispenser and the sensor system.
22
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Commissioning
6
Commissioning
6.1
Personnel qualification
Commissioning must only be carried out by qualified personnel
(see section 2.2.2).
6.2
Starting the commissioning procedure
When the machine is turned on for the first time, the commissioning procedure starts automatically with the language selection,
followed by further requisite commissioning steps.
►► Push ON/OFF button .
Display is activated.
Language menu is displayed.
6.3
Setting the language
►► Push display navigation button „ or † until the required language is highlighted.
►► Push button ….
The language is activated.
Set day menu is displayed.
6.4
Setting the date
►► Push display navigation button „ or † until the required day is
highlighted.
►► Confirm with button … and skip to set month.
►► Repeat the procedure as described to enter month and year.
►► Push button ….
The date is activated.
Set time menu is displayed.
6.5
Setting the time
►► Push display navigation button „ or † until the required hour is
highlighted.
►► Confirm with button … and skip to set minutes.
►► Push display navigation button „ or † until the required minute
is highlighted.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
23
EN
EN
PROFI UXTH
Installation and Operation Instructions
Commissioning
►► Push button ….
The time is activated.
6.6
Filling chemical hoses
i
!
We recommend the use of HOBART Hyline detergent
and rinse aid.
CAUTION
Chemical burns, sensitisation of the skin, poisoning
The use of unsuitable chemicals can cause injury.
►► Use only commercial detergent and rinse aid.
►► Observe the manufacturer’s application and safety instructions.
!
WARNING
Chemical burns, sensitisation of the skin, poisoning
Filling the chemical container or chemical hoses with detergent or
rinse aid for the first time incorrectly can cause serious injury.
►► Wear protective equipment (gloves, safety goggles, protective
clothing) when handling chemicals.
6.6.1
Provisioning external chemical canisters
During the commissioning procedure, an instruction for inserting
the suction hoses into the external canisters appears in the display.
Preparing the detergent:
99 Suction height of dosing pump: max. 1.5 m.
►► Place suction hose without colour marking at the suction valve
at the bottom of the external reservoir.
Preparing the rinse aid:
99 Suction height of dosing pump: max. 1.5 m.
►► Place suction hose with blue marking at the suction valve at the
bottom of the external reservoir.
Filling the suction hoses:
►► Push button ….
The instruction “Close the machine hood” is displayed.
►► Close the hood and push button ….
Chemical hose filling is activated.
The filling process is visualised in the display by a time bar.
24
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Commissioning
6.7
Completing the commissioning procedure
The machine can be started or switched off selectively.
►► Push display navigation button „ or † until the required setting
is highlighted.
►► Push button ….
The setting is activated.
6.8
Starting up the chemical deficiency sensor
system
!
WARNING
Chemical burns, sensitisation of the skin, poisoning
Incorrect procedure when commissioning the chemical sensor
system can cause serious injury.
►► Have chemical sensor system set by authorised service technicians.
►► Before removing the trim components, disconnect the machine
from the power supply.
►► Execute hose filling via the operator menu (see section 8.8).
►► Observe until the sensor-operated filling of both hoses is complete.
The control LEDs must now illuminate.
►► If necessary, readjust the potentiometers (increase setting).
–– Factory setting for detergent = 3
–– Factory setting for rinse aid = 5
►► Switch on sensor system in the service menu. Contact your
HOBART Service Partner.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
25
EN
EN
PROFI UXTH
Installation and Operation Instructions
Operation
7
Operation
7.1
Personnel qualification
The machine must be operated by instructed personnel (see section 2.2.2).
7.2
Special safety instructions
!
WARNING
Fire hazard
Malfunction or continuous operation of the machine can cause
injuries due to fire.
►► Do not operate the machine without supervision.
!
CAUTION
Chemical burns, sensitisation of the skin, poisoning
If the hood is opened during operation, wash water can spurt out
and cause injury.
►► Do not open the hood during operation, wait for the program to
finish.
!
WARNING
Slipping
Moisture can build up on the machine floor and cause slipping.
►► Provide a floor covering that is guaranteed to be non-slip in
case of moisture.
26
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Operation
7.3
Preparations for washing
7.3.1
Preparing the machine
►► Check correct position of wash/rinse arms and strainers.
►► Open site shut-off valve.
►► Turn on main switch or insert the plug.
►► Check level of detergent and rinse aid containers.
►► Close hood.
►► Push the ON/OFF button .
Machine is switched on.
The tank is filled.
The ON/OFF button will become gradually green during fill and
heating cycle. This process can take several minutes.
When the button becomes completely green, the machine is ready
for operation.
7.3.2
Preparing the washware
►► Remove large scraps.
►► Remove foaming products (protein, parting agents, blood etc.).
►► Pre-treat (e.g. soften) soiling that has baked-on hard.
►► Place plates in the correct insert rack
►► Avoid shadow zones and covers.
►► Place pots and containers face down in the racks.
►► Secure lightweight wash ware by attaching a rack or the special
loading frame!
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
27
EN
EN
PROFI UXTH
Installation and Operation Instructions
Operation
7.4
Displaying and selecting the program
7.4.1
Overview of programs and additional functions
Name
Description
Short
For slight contamination
Standard
For normal contamination
Intensive
For heavier soiling
Low Temp
Works at reduced temperature to prevent protein coagulation (not activated in the factory)
Continuous
For heavy contamination
Hygiene
(see also section 7.10)
7.4.2
Alternative
symbol display
Displaying and selecting the program
The machine rinses automatically using the standard program. If
necessary, a different program can be selected.
►► To display the current program before the start, activate the infrared sensor in the display by hand or push the display navigation button.
Display is activated.
Program selection and info menu is displayed.
The program currently selected is highlighted.
►► To switch to a different program, press the navigation button „
or † until the required program appears and is highlighted.
The selected program can be started directly via ON/OFF button
.
The machine continues with the last program to be selected until it
is switched off.
28
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Operation
7.5
Washing
►► Slide rack into the machine and close the hood.
While the programme is running, the ON/OFF button gradually changes from blue back to green.
As soon as the ON/OFF button illuminates green again, the
rinse cycle is finished.
►► Open the hood and remove the rack.
►► Allow the washware enough time to dry.
7.5.1
Ending a continuous program
A running continuous program can be ended prematurely as follows.
►► Push the ON/OFF button .
The rinse cycle starts after a short pause.
The continuous program is ended.
The program also ends automatically after 20 minutes.
7.6
Special features in operation with hood lift
(optional)
!
CAUTION
Risk of being cut or crushed
During manual operation, the hood or hood bracket may drop and
cause injuries.
►► During manual operation, the hood/hood bracket must be secured by a second person.
►► If the racks or wash ware block the hood, for example, wait
until the hood opens again automatically (after 5 seconds at
the latest). If the hood does not re-open automatically, contact
Service.
Preparation:
►► Press the ON/OFF button .
The hood closes and the tank is filled.
As soon as filling is completed, the hood opens and the ON/OFF
button illuminates green.
Washing:
►► Push rack into the machine and close hood by pressing the
HOOD LIFT or ON/OFF button.
As soon as the ON/OFF button illuminates green again, the
wash cycle is finished and the hood opens automatically.
►► To prevent cooling during interval times, press the HOOD LIFT
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
29
EN
EN
PROFI UXTH
Installation and Operation Instructions
Operation
button and hold until the hood is closed.
Further hood lift functions
–– Closing and opening the hood can be interrupted by briefly
pressing the HOOD LIFT button.
–– If the hood is not completely closed within 5 seconds (e.g. rack
blocks the closing process), it is automatically stopped and reopened (after 5 seconds at the latest).
–– The hood bracket may be used manually only in case of a drive
failure. For safety reasons, this must be done by 2 persons.
7.7
Switch off machine
►► Close hood.
►► Push the ON/OFF button  for 3 seconds.
During pump-out, the ON/OFF button gradually changes
from green back to colourless.
i
During the drain cycle, the machine interior is cleaned
automatically. Then remove any food debris.
If the interior is sprayed out again manually with a
water hose, this residual water can be pumped out
again with a reduced pump-out phase by pressing
and holding down the ON/OFF button (3 sec.) when
the machine has been switched off.
99 When the ON/OFF button has extinguished completely:
►► Turn off main switch or remove the plug.
►► Close on-site shut-off valve.
i
30
If no button is pressed, the machine switches off automatically after 6 hours, but will not pump out.
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Operation
7.8
Executing daily cleaning
!
WARNING
Burns, scalds, chemical burns
During the cleaning process, general malfunctions with the washing, rinsing or cleaning pump or the tank heater, for example, can
cause injuries from burns, scalds or chemical burns.
►► The machine must be disconnected from the mains prior to
cleaning.
►► Wear protective gloves.
NOTICE
Property damage
The use of unsuitable agents can cause corrosion damage.
►► Do not use any chloric, acidic or metal-containing additives to
clean the machine.
►► Do not use metal sponges.
►► Open hood.
►► Remove sieves and clean. Make sure that food debris does
not enter pump intake!
►► Flush the fine strainer under running water.
►► Clean machine areas that cannot be reached by the water circulation of the self cleaner (hood labyrinth, rear side riser pipe,
etc.).
►► Replace strainer.
►► Leave the hood open for ventilation.
7.9
Executing weekly cleaning
►► Push and hold the clip fastener on the wash and rinse arms.
Remove the wash and rinse arms and clean.
►► Reinsert wash and rinse arms.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
31
EN
EN
PROFI UXTH
Installation and Operation Instructions
Operation
7.10 Executing hygiene cleaning
When a pre-set number of rinse cycles has been reached, the
instruction “Execute hygiene program” appears in the display,
indicating that an automatic hygiene clean of the machine interior
should be executed.
►► Before end of operation, remove the rack and place 10 HOBART cleaning tablets in the machine interior.
►► Close hood.
►► Push  or  navigation button until the hygiene program appears and is highlighted.
►► Press the ON/OFF key .
While the hygiene program is running (duration up to one hour,
depending on model and water connection), the green illuminated
segments extinguish successively.
At the end of the program, the machine switches off automatically.
i
If necessary, hygiene clean should be executed
before the pre-set number of rinse cycles is reached.
With regular use, the machine interior will remain free
of food debris and deposits.
7.11 Changing the chemical product
When changing the detergent and rinse aid product, please note
the following:
–– Mixing dissimilar products can produce efflorescence, which
in turn can cause the dispenser to malfunction. This is also the
case if the new product is from the same manufacturer.
–– A new product may require the dispenser to be adjusted.
–– The complete system, consisting of dosing hoses and dispenser, must be rinsed with water before the new chemical is used.
Changing the chemical:
►► Remove the suction valve from the reservoir and place in a
container full of water.
►► Rinse dosing hoses and detergent dispenser with water
–– Use the “Fill chemical hoses” function 8.8.
–– Repeat if necessary. This depends on the length of the dosing hose.
–– Place the suction lace in the reservoir together with the new
product.
►► To replace the water in the dosing hoses with the product, use
the “Fill chemical hoses” function 8.8.
32
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Operation
7.12 Displaying the temperatures
This menu option is for displaying the current tank and rinsing
temperatures.
Procedure:
►► Activate the infrared sensor in the display by hand or push one
of the display navigation buttons.
Display is activated.
Program selection and info menu is displayed.
►► Push button .
Login/Temperatures/Info menu is displayed.
►► Select the Temperatures menu option.
Current tank and rinsing temperatures are displayed.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
33
EN
EN
PROFI UXTH
Installation and Operation Instructions
Setting options, operating and hygiene data
8
Setting options, operating and hygiene data
The machine can be operated as soon as the commissioning procedure is complete.
The following settings can be individually set as required using the
operator menu.
8.1
Overview of operator menu
Sub-menu
Function
General settings
Language
Date
Time
Date format
Time format
Temperature unit
Display indications
Program representation
Brightness
Adjust contrast
Temperature display
Acoustic signal
On/Off
Chemical settings
Detergent dosing
Rinse aid dosing
Filling chemical hoses
External water treatment (only
when activated by HOBART
Service)
Set counter
Operating/hygiene data
Display operating data
Reset counter
Remaining water quantity
Display hygiene data
Transmit report
Timer
Weekly program
Timer program
Activate/deactivate
34
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Setting options, operating and hygiene data
8.2
Opening the operator menu
99 The machine must be switched on.
►► Activate the infrared sensor in the display by hand or push one
of the display navigation buttons.
Display is activated.
Program selection and info menu is displayed.
►► Push button ….
Login/Temperatures/Info menu is displayed.
►► Push display navigation button † until Login is highlighted.
►► Push button ….
Enter PIN is displayed.
Enter operator code “1111”:
►► Push display navigation button „ or † until a "1" is shown in
the first place.
►► Push button … and skip to the next number.
►► Repeat the procedure as described until all numbers are entered.
The operator menu is displayed once the correct code has been
entered.
8.3
Navigating, selecting and setting within the
menu
Navigating and opening sub-menu:
►► Push „ or † navigation button until the required sub-menu appears and is highlighted.
►► Push button ….
Menu is displayed.
Making and activating settings:
►► Push display navigation button „ or † until the required setting
is displayed and highlighted.
►► Push button ….
The setting is activated.
Back:
►► Push „ or † navigation button until the Back menu option appears and is highlighted.
►► Push button ….
The next highest menu level is displayed.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
35
EN
EN
PROFI UXTH
Installation and Operation Instructions
Setting options, operating and hygiene data
8.4
Exiting the operator menu
►► Open the hood and close it again, or do not press a key for 10
seconds!
8.5
Making the general settings
The following settings can be entered into the General settings
sub-menu.
Setting
Selection
Language
is set as default during commissioning, see sections 6.3 to 6.5
Date
Time
Date format
YYYY.MM.DD
DD.MM.YYYY
MM.DD.YYYY
Time format
24h / 12h
Temperature unit
°C / °F
Making the settings:
►► Open the operator menu, see section 8.2.
►► Open the General settings sub-menu and make the setting,
see section 8.3.
8.6
Setting the display indications
The following settings can be entered into the Display indications
sub-menu.
Setting
Selection
Program representation
Text display
Symbol display (see section 4.6.1)
Display brightness
Set brightness
Display contrast
Set contrast
Temperature display
Activate/deactivate
Making the settings:
►► Open the operator menu, see section 8.2.
►► Open the Display indications sub-menu and make the setting,
see section 8.3.
36
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Setting options, operating and hygiene data
8.7
Setting the acoustic signal
An acoustic signal can be switched on or off in the Acoustic signal sub-menu.
Setting
Selection
Set signal sensor
Sound on/sound off
Making the settings:
►► Open the operator menu, see section 8.2.
►► Open the Acoustic signal sub-menu and make the setting, see
section 8.3.
8.8
Making the chemical settings
The following settings can be entered into the Chemical settings
submenü.
Setting
Selection
Detergent dosing
Factory setting: 2.5 g/l
Possible range: 0–9.5 ml
Rinse aid dosing
Factory setting: 0.3 g/l
Possible range: 0–2.0 g/l
Filling chemical hoses
Fill detergent suction hose NO/YES
Fill rinse aid suction hose NO/YES
Making the settings:
►► Open the operator menu, see section 8.2.
►► Open the Chemical settings submenü and make the setting,
see section 8.3.
If in theFill chemical hoses submenu, the prompt Fill detergent
suction hose and/or Fill rinse aid suction hose are set to Yes,
the filling process will start.
The filling process is visualised in the display by a time bar.
NOTE: The hose filling for detergent only functions when the
door/hood is closed.
It can be stopped by pushing button ‚ if necessary.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
37
EN
EN
PROFI UXTH
Installation and Operation Instructions
Setting options, operating and hygiene data
8.9
Configuring the counter for external water
treatment (optional)
The following settings for an optional external water treatment can
be entered into the External water treatment sub-menu.
Setting
Selection
Set counter
Set counter
Factory setting: not activated
Reset counter
Reset counter NO
Reset counter YES
Remaining water quantity
Remaining capacity for external
water treatment
Displays the current demineralisation counter status (water quantity
remaining until the desalination
cartridge is depleted).
Making the settings:
►► Open the operator menu, see section 8.2.
►► Open the External water treatment sub-menu and make the
setting, see section 8.3.
8.10 Displaying the operating/hygiene data
The following data can be called-up from the Operating/hygiene
data sub-menu.
Setting
Selection
Display operating data
Commissioning date
Operating hours until next service
Operating hours overall
Wash cycles overall
Water consumption overall
Operating days/hours
Daily wash cycles
Daily water consumption
Remaining capacity for external
water treatment
Hygiene data
See section 8.10.1
Report
See section 8.10.2
Display the setting:
►► Open the operator menu, see section 8.2.
►► Open the Operating/hygiene data sub-menu.
38
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Setting options, operating and hygiene data
►► Open the corresponding sub-menu and display the setting, see
section 8.3.
8.10.1 Display hygiene data
Hygiene-relevant events, data and messages are listed in this
menu option.
The list starts with the current date and the last event that occurred
on this day. The subsequent events occurring on this day then appear, followed by the events occurring the day before.
A maximum of 1500 events are saved. Older lists are deleted.
Pushing button … opens the list of completed wash programs.
The following data are saved:
Hygiene data
Program set point temperature too
low
Thermal disinfection aborted
Wash process aborted
Messages
Rinse aid empty
Rinse aid deficiency remedied
Detergent empty
Detergent deficiency remedied
Salt empty
Salt deficiency remedied
Service interval expired
Half-cartridge depleted
Events
Filling program
Pump-out program
Washing program
8.10.2 Transmit report
This menu option is for transmitting operating and hygiene-relevant
data in txt format to a USB stick. This format can be imported and
processed using standard software.
Procedure:
►► Open the door.
►► Remove sealing cover from USB port (top right near door sealing).
►► Insert USB stick into the port.
►► Select the Report menu option.
After a successful download, a message appears in the
display.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
39
EN
EN
PROFI UXTH
Installation and Operation Instructions
Setting options, operating and hygiene data
►► Remove USB stick.
►► Close off USB port with the sealing cover.
8.11 Setting automatic switch-on
The Timer sub-menu is for defining times for automatic machine
switch-on.
This can be done in two ways:
–– The Weekly program menu option can be used to define various switch-on times for individual weekdays.
–– The Daily Timer program can be used to define a non-recurring switch-on time for today’s date.
The switch-on must be set to active via the separate Activate/
deactivate menu option. The text frame shows the most recently
selected of the four options. When switch-on is activated, a small
clock symbol remains in the top left-hand section of the display for
30 minutes after the machine has been turned off.
Setting
Selection
Weekly program
Weekdays and times
Daily Timer program
Date and time
Activate/deactivate
Weekly timer ON
Daily Timer program ON
Weekly and Daily Timer program
ON
Timer OFF
Making the settings:
►► Open the operator menu, see section 8.2.
►► Open the Timer sub-menu and make the setting, see section
8.3.
Daily Timer program
The date and time can be selected and altered using the display
navigation buttons.
The switch-on must also be set to active via the separate Activate/
deactivate menu option.
When the time and date are reached, the machine switches on.
Weekly program
Weekdays and an individual switch-on time can be selected and
altered using the display navigation buttons.
For weekdays on which no switch-on is to occur, no time may be
saved.
After the switch-on times for each weekday have been entered, the
switch-on must be set to active via the separate Activate/deactivate menu option.
When the time is reached, the machine switches on.
Activate/deactivate
40
The Activate/deactivate menu option offers the following four
selection options:
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Setting options, operating and hygiene data
–– Daily timer on: Automatic switch-on is activated for an entered
day’s date.
–– Weekly timer on: Automatic switch-on is activated for the
saved weekdays and individual times.
–– Daily and weekly timer on: Automatic switch-on is activated
for an entered day’s date and for the saved weekdays.
–– Timer off: Automatic switch-on is generally deactivated.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
41
EN
EN
PROFI UXTH
Installation and Operation Instructions
Fault indications and problems
9
Fault indications and problems
9.1
Fault indications
Displayed error messages are shown in the order of priority.They
must be acknowledged via the display navigation button ….
Acknowledged error messages for which the error is still pending
are first hidden to enable further messages to be displayed.
If all fault messages have been acknowledged but errors are still
pending, these messages will then be shown again.
Information
–– Limited operation is possible.
–– The ON/OFF button  illuminates green/red alternately.
–– The error code is shown in the display (see table).
Error code
Message text
Measure
003
Temperature not reached. Contact service
technician.
Contact your HOBART Service Partner.
004
Temperature not reached. Contact service
technician.
Contact your HOBART Service Partner.
008
Temperature not reached. Contact service
technician.
Contact your HOBART Service Partner.
009
Temperature not reached. Contact service
technician.
Contact your HOBART Service Partner.
021
Fault in the drain system. Clean the drain hose
if necessary and pump-out the machine again.
Clean the drain hose if necessary and pumpout the machine again.
022
Fault in the drain system. Clean the drain hose
if necessary.
Clean the drain hose if necessary.
029
Program aborted. Close hood.
Close hood.
036
Detergent deficiency. Refill detergent.
Refill detergent (see section 6.6).
037
Rinse aid deficiency. Refill rinse aid.
Refill rinse aid (see section 6.6).
038
Input voltage too high! Machine has been
switched off.
Have the input voltage checked by the (site)
electrician.
039
Filling program aborted. Close hood.
Close hood.
041
External water treatment depleted. Replace.
Replace part or full desalination cartridge.
042
Osmosis pre-filter depleted. Replace.
Replace pre-filter.
043
Salt deficiency. Refill regenerating salt.
Refill regenerating salt.
42
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Fault indications and problems
Faults
–– Limited operation is not possible.
–– The ON/OFF button  illuminates red permanently.
–– The error code is shown in the display (see table).
–– Once the error display has been acknowledged, the machine
turns off.
Error code
Message text
Measure
001
Hot water tank temperature sensor fault. Contact service technician.
Contact your HOBART Service Partner.
002
Hot water tank temperature sensor fault. Contact service technician.
Contact your HOBART Service Partner.
006
Wash tank temperature sensor fault. Contact
service technician.
Contact your HOBART Service Partner.
007
Wash tank temperature sensor fault. Contact
service technician.
Contact your HOBART Service Partner.
011
Wash chamber temperature sensor fault. Contact service technician.
Contact your HOBART Service Partner.
012
Wash chamber temperature sensor fault. Contact service technician.
Contact your HOBART Service Partner.
013
Disinfection not guaranteed. Contact service
technician.
Contact your HOBART Service Partner.
014
Hot water tank pressure sensor fault. Contact
service technician.
Contact your HOBART Service Partner.
015
Hot water tank pressure sensor fault. Contact
service technician.
Contact your HOBART Service Partner.
016
Wash tank pressure sensor fault. Contact service technician.
Contact your HOBART Service Partner.
017
Tank pressure sensor fault. Contact service
technician.
Contact your HOBART Service Partner.
018
Fault in the filling or drain system. Contact service technician.
Contact your HOBART Service Partner.
019
Strainers blocked. Remove, clean and re-insert. Remove, clean and re-insert strainers.
020
Wash tank pressure sensor fault. Pump out
machine.
Pump out machine.
023
Fault in the filling system. Supply quantity too
low.
Check site flow pressure.
031
Fault in the filling system. Check water supply.
Check water supply.
032
Fault in the filling system. Check water supply.
Check water supply.
033
Fault in the filling system. Contact service technician.
Contact your HOBART Service Partner.
035
Insert tank cover strainer correctly.
Insert tank cover strainer correctly.
044
Salt deficiency. Refill regenerating salt.
Refill regenerating salt.
045
Number of rinse cycles without regenerating
salt exceeded. Contact service technician.
Contact your HOBART Service Partner.
052
Fault in the filling or drain system. Contact service technician. Disconnect machine from the
water and power supply!
Contact your HOBART Service Partner.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
43
EN
EN
PROFI UXTH
Installation and Operation Instructions
Fault indications and problems
9.2
Remedying the problem
9.2.1
Poor wash result
Nature of the problem Possible cause
Washware not clean.
Remedy
Wash arms stiff (you should be able to turn Remove wash arms and clean them thorthem easily by hand).
oughly.
Also check water outlet from machine to
wash arms is clear.
Wash arm nozzles are clogged (visual
check).
Remove wash arms, remove cleaning
caps and rinse wash arms thoroughly until
all soiling is removed.
Replace cleaning caps.
Rinse nozzles clogged (usually by lime
deposit).
Remove rinse arms and decalcify them in
separate container.
Check site softener system for function.
Regeneration concentration is too low or
too high.
Check detergent concentration setting.
Coarse strainer clogged.
Remove, empty and clean strainer.
Fine strainer clogged or obstructed by lime Remove fine strainer. If heavily soiled,
deposits.
soak in a vinegar solution. Then clean it
thoroughly with a brush until the pores are
free.
The fine strainer should generally be
cleaned daily (see operating instructions).
Wrong program selected for heavily soiled
washware.
Washware does not dry Rinse aid dosing too low.
properly.
Washware still greasy.
Select program with longer wash cycle.
Increase concentration (see operating
instructions).
Detergent concentration too low: increase
(see operation instructions).
Check if detergent is appropriate. If not,
choose a stronger one.
Drain contaminated water and refill machine. Clear washware more thoroughly
beforehand.
44
Rack is not suitable for type of dishes
(sloping).
Use appropriate racks to create a sloping
position which allows water to drain away
from cavities.
Washware remains in the machine too
long at the end of rinse cycle.
Remove washware as soon as cycle is
completed to enable it to dry.
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Fault indications and problems
Nature of the problem Possible cause
Remedy
Streaks and spots on
washware.
Rinse aid concentration too high (stripe or
bubble formation).
Reduce concentration (see operating
instructions).
Hard water or high mineral content.
Check water quality.
Every local water works holds data on the
composition of the water they supply and
will provide these on request.
Reference values: Ideal calcium value: 0 –
3 °d (total hardness). Ideal mineral content
value: for glasses, max. conductivity 100
µS/cm, for dishes, still viable to max. 400
µS/cm.
Rack is not suitable for type of dishes
(sloping).
Use appropriate racks to create a sloping
position which allows water to drain away
from cavities.
Inadequate rinse aid dosing causes stains. Increase rinse aid concentration (see operating instructions).
Machines with integrated softener: use of
wrong salt (e.g. tablets).
9.2.2
Do not use salt tablets.
Other problems
Nature of the problem Potential causes
Remedy
Machine becomes significantly louder during
the wash program.
Excessive foaming from unsuitable detergent or rinse aid
Use suitable detergent and rinse aid.
Excessive foaming due from foaming substances (protein, parting agents, etc.)
Preliminary clean the wash ware thoroughly.
Machine switches off
suddenly during operation.
Machine coupled to a maximum system or
locked against other current consumers.
Have machine connected separately (electrician!).
A site fuse has tripped.
Check site fuses.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
45
EN
EN
PROFI UXTH
Installation and Operation Instructions
Maintenance
10
Maintenance
In order to maintain the warranty, as well as a permanently safe,
efficient, and trouble-free operation of the machine(s), the required
maintenance must be carried out by authorized service technicians.
We therefore recommend the conclusion of an inspection and
maintenance contract, which guarantees qualified support by
specially trained service technicians according to a time schedule
based on the operating conditions.
Genuine spare parts must be used for repairs and wearing part
replacements. Wearing parts include dosing hoses, rinse arm bearings etc.
In Germany, your HOBART machines are governed by the Ordinance on Industrial Health and Safety and must be inspected by
a qualified electrician in accordance with the intervals specified in
BGV A3.
46
IO-0000000199-001-EN / 5. Oct. 2015
HOBART
PROFI UXTH
Installation and Operation Instructions
Disposal
11
Disposal
The machine operator is responsible for disposing of the machine
and its operating materials correctly and in accordance with environmental regulations. Both national and local legal provisions and
regulations must be observed!
With respect to fluorine-containing coolants in machines with heat
pumps, the requirements of Regulation (EC) No. 517/2014 and
supplementary national legislation must be observed in Europe.
We recommend assigning a specialist company for disposal.
Alternatively, Hobart can take back the machine and its operating
materials.
HOBART
IO-0000000199-001-EN / 5. Oct. 2015
47
EN
HOBART GmbH
Robert-Bosch-Str. 17
77656 Offenburg
Deutschland
Tel.: +49 (0)781.600-0
Fax: +49 (0)781.600-23 19
E-Mail: info@hobart.de
Internet: www.hobart.de
HOBART Export
Robert-Bosch-Str. 17
77656 Offenburg
Germany
Phone: +49 (0)781.600-2820
Fax: +49 (0)781.600-2819
E-Mail: info-export@hobart.de
Internet: www.hobart-export.com
Hobart UK.
Southgate Way,
Orton Southgate,
Peterborough
PE2 6GN
United Kingdom
Tel.: +44 (0)844 888 7777
Republic of Ireland: +353 (0)1246 0248
Fax: +44 (0)1733 361 347
E-mail: sales@hobartuk.com
Internet: www.hobartuk.com
Compagnie HOBART SAS
Allée du 1er mai
77183 Croissy Beaubourg
FRANCE
Tel: +33 (0)1 64 11 60 00
Fax: +33 (0)1 64 11 60 10
E-mail: contact@hobart.fr
Internet: www.hobart.fr
Hobart Nederland BV
Pompmolenlaan 12
3447 GK Woerden
Telefoon +31 (0)348 462626
Fax: +31 (0)348 430117
E-mail: info@hobartnederland.nl
Internet: www.hobartnederland.nl
Hobart Foster Belgium bvba/sprl
Industriestraat 6
1910 Kampenhout
Telefoon +32 (0) 16.60.60.40
Fax +32 (0) 16.60.59.88
E-mail: info@hobart.be
Internet: www.hobart.be
Printed in Germany
48
IO-0000000199-001-EN / 5. Oct. 2015
Hobart Norge
Gamle Drammenvei 120
N-1363 Høvik
Tlf.: +47-67109800
Fax.: +47-67109801
E-post: post@hobart.no
Hjemmeside: www.hobart.no
Hobart Scandinavia ApS
Håndværkerbyen 27
2670 Greve
Danmark
Tlf.: +45 4390 5012
Fax.: +45 4390 5002
E-mail: salg@hobart.dk
Internet: www.hobart.dk
Hobart Sweden/Finland
Tel: +46 8 584 50 920
E-mail: info@hobart.se
Internet: www.hobart.se
Australia
Hobart Food Equipment
Unit 1 / 2 Picken Street,
Silverwater NSW, 2128
Tel: +61 1800 462 278
Fax: +61 02 9714 0222
E-mail: sales@hobartfood.com.au
Internet: www.hobartequipment.com.au
HOBART China
15th Floor, Building A
New Caohejing International Business
Center
391 Gui Ping Road
Shanghai, 200233
Telephone: +86 (0)21 34612000
Fax: +86 (0)21 34617166
Internet: www.hobartchina.com
Download PDF
Similar pages