INSTRUCTIONS for installation and use

ELF063CS
WARMING DRAWER FOR
RESIDENTIAL USE
INSTRUCTIONS
for installation and use
GB
Dear Customer,
we would like to thank you and congratulate you on your
choice.
This new product has been carefully designed and built
using top quality materials, and meticulously tested to
ensure that it meets all your culinary requirements.
Please read and observe these simple instructions, which
will enable you to achieve excellent results from the very
first time you use it. This state-of-the-art appliance comes
to you with our very best wishes.
THE MANUFACTURER
I
Italiano
GB
English
FR
Français
DE
Deutsch
ES
Español
PT
Português
UNSUITABLE USE.
THE APPLIANCE MUST NOT BE USED BY PEOPLE
(INCLUDING
CHILDREN)
WITH
PHYSICAL,
SENSORIAL OR MENTAL IMPAIRMENTS, OR BY
PEOPLE WITHOUT THE NECESSARY EXPERIENCE
OR KNOWLEDGE, UNLESS THEY ARE SUPERVISED
OR INSTRUCTED IN THE USE OF THE APPLIANCE
BY A PERSON RESPONSIBLE FOR THEIR SAFETY.
CHILDREN MUST BE SUPERVISED TO ENSURE
THAT THEY DO NOT PLAY WITH THE APPLIANCE.
THIS PRODUCT IS DESIGNED FOR DOMESTIC USE.
THIS APPLIANCE IS INTENDED FOR DOMESTIC
AND SIMILAR USE, SUCH AS:
- IN THE STAFF KITCHEN AREAS OF STORES,
OFFICES AND OTHER WORKPLACES;
- IN FARMHOUSES;
- FOR USE BY HOTEL AND MOTEL GUESTS AND
OTHER PROFESSIONAL ENVIRONMENTS;
- IN BED-AND-BREAKFASTS.
THE
MANUFACTURER
DECLINES
ALL
RESPONSIBILITY FOR DAMAGES TO THINGS
OR PEOPLE DERIVING FROM INCORRECT
INSTALLATION OR IMPROPER, ERRONEOUS OR
2
Officine Gullo
16
Table of Contents
1. PRECAUTIONS
2. INSTRUCTIONS FOR RECYCLING PROTECTION OF THE ENVIRONMENT
3. SAFETY INSTRUCTIONS
4. APPLIANCE DESCRIPTION
5. BEFORE YOU BEGIN
6. CONTROL PANEL
7. USING YOUR WARMING DRAWER
AND
MAINTENANCE
8. CLEANING
USING YOUR
WARMING
DRAWER
9. TROUBLESHOOTING
10. APPLIANCE INSTALLATION
GB
CONSUMER INSTRUCTIONS: Includes
recommendations for use, description of
commands and correct procedures for the care
and clearing of the appliance.
INSTALLATION INSTRUCTIONS: Use
intended for qualified technicians.
3
Officine Gullo
17
GB
1. PRECAUTIONS
a risk for children.
This guide is an integral part of the appliance. Keep these
instructions with you during use of your warming drawer.
Read these instructions before installing and using the
appliance. Installation should be performed by qualified
personnel only, in conformity with current law. This
appliance is intended for domestic use only in conformity
with current EEC directives. The manufacturer will not
be held liable in the event of a failure to follow THESE
WARNINGS AND SAFETY INSTRUCTIONS. KEEP
THESE INSTRUCTIONS WITH THE APPLIANCE. IF
THE APPLIANCE SHOULD BE GIVEN TO ANOTHER
PERSON MAKE SURE THESE INSTRUCTIONS ARE
SUPPLIED WITH IT.
Your old appliance must also be disposed of properly.
Important: consign the appliance to the proper local
organization authorized to collect broken appliances.
Proper and intelligent disposal consists of recovering
materials of value.
Remove the plugs or electrical cords of appliances that
are no longer being used so that they no longer pose a
threat to children.
3 SAFETY INSTRUCTIONS
The safety measures regarding the electric, gas and
functions are found in the installation section. It is in
your best interest and safety and also legally required
that all electrical appliances be installed and repaired
exclusively by qualified personnel in conformity
with current standards. Our qualified personnel can
guarantee that the works will be performed correctly. Gas
and electric appliances must always be disconnected by
experienced personnel. Before connecting appliances
to electric circuits it is important to check and compare
the connection data (voltage and frequency) shown
on the label to the characteristics of the local electric
line. It is essential that this data coincide in order to
avoid damaging the appliances. For further help and
assistance please contact your local electrician.
DO NOT USE THE APPLIANCE FOR HEATING
PURPOSES. HIGHLY FLAMMABLE OBJECTS ARE
AT RISK OF CATCHING FIRE IF PLACED IN THEIR
PROXIMITY DUE TO ELEVATED TEMPERATURES.
DO NOT DISPOSE OF MATERIALS IN THE
HOME. SORT THE VARIOUS MATERIALS BY
CLASSIFICATION AND DISPOSE OF THEM
PROPERLY.
THE LABELS DISPLAYED ON THIS APPLICATION
ARE IN COMPLIANCE WITH THE DIRECTIVE 2002/96/
CEE WASTE AND ELECTRICAL EQUIPMENT (WEE).
DO NOT OBSTRUCT THE OPENINGS AND FIXTURES
INTENDED FOR HEAT CIRCULATION.
The electrical safety of the appliance is only guaranteed
when attached to a ground conductor. The manufacturer
will not be liable for damages caused by the absence or
interruption of a ground conductor (i.e. electric shock).
THE LABELS LOCATED ON THE APPLIANCE WHICH
SHOW THE SERIAL NUMBER AND MODEL ARE
FOUND ON THE HEATING BLOCK. NEVER REMOVE
THE DATA LABEL.
The appliance must be installed and connected by a
specialized electrician. If necessary, contact a local
electrician who is familiar with local standards and
regulations. The manufacturer will not be liable for
damages caused by incorrect installation or installations
not conforming to local and national laws.
WARNING! NEVER USE SHARP METAL OBJECTS OR
ABRASIVE SCRUBBING PADS THAT COULD CAUSE
DAMAGE TO THE SURFACE OF THE APPLIANCE.
IF NECESSARY, USE STANDARD NON-ABRASIVE
UTENSILS MADE OF WOOD OR PLASTIC.
WARNING! IN ORDER TO AVOID THE RISK OF
ELECTRICAL SHOCK ONLY USE APPLIANCES THAT
HAVE BEEN INSTALLED CORRECTLY.
2. INSTRUCTIONS FOR RECYCLING
- PROTECTION OF THE ENVIRONMENT
WARNING! NEVER OPEN THE HOUSING OF THE
APPLIANCE. IF YOU COME INTO CONTACT WITH
PARTS UNDER PRESSURE OR IF THE ELECTRICAL
AND/OR
MECHANICAL
STRUCTURES
ARE
MODIFIED, THIS COULD DAMAGE THE APPLIANCE
AND CAUSE IT TO MALFUNCTION.
Our products are made solely from non-polluting
materials that do not harm the environment and are
recyclable. We ask for your effort and collaboration in
disposing of the packaging in a proper manner. Contact
the product retailer or local organizations for further
information on recycling. Dispose of the packaging
properly. Parts of the package especially plastic, pose
4
18
18
Officine Gullo
WARNING! DO NOT KEEP PLASTIC CONTAINERS
OR ANY FLAMMABLE OBJECTS IN THE APPLIANCE.
SUCH OBJECTS POSE A RISK OF CATCHING FIRE
ONCE THE WARMING DRAWER IS TURNED ON.
• ATTENTION! Before beginning maintenance,
installation, or repair work disconnect the appliance from
the electrical outlet.
The appliance is disconnected only if:
- The electrical fuse is disconnected.
- The cord of the appliance is disconnected from the
electrical outlet – to disconnect the appliance from
the outlet pull the cord away from the outlet, manually
disconnect the cord. The manufacturer will not be
liable for damage caused by a failure to follow current
regulations or the use of non-original replacement
parts.
WARNING! THIS APPLIANCE IS NOT SUITABLE
FOR USE BY PEOPLE (CHILDREN INCLUDED)
WITH PHYSICAL, SENSORIAL, AND/OR MENTAL
IMPAIRMENTS. PEOPLE WITHOUT THE NECESSARY
EXPERIENCE OR KNOWLEDGE OF THE APPLIANCE
MUST BE SUPERVISED BY A RESPONSIBLE
PERSON FOR THEIR OWN SAFETY. CHILDREN
MUST BE SUPERVISED TO ENSURE THEY DO NOT
PLAY WITH THE APPLIANCE.
WARNING: REMEMBER THAT CHILDREN’S SKIN
IS MORE DELICATE AND SENSITIVE TO HIGH
TEMPERATURES. KEEP APPLIANCE AWAY FROM
CHILDREN. APPLIANCE MAY OVERHEAT IF USED
INCORRECTLY: RISK OF BURNS
GB
4. INSTRUCTIONS FOR THE CONSUMER
4.0 OPENING OF THE DRAWER
To open the drawer press the front of the drawer
WARNING: THE INSIDE OF THE APPLIANCE CAN
REACH TEMPERATURES OF 75°C DEPENDING ON
THE SELECTED TEMPERATURE AND THE TIME
OF OPERATION. IF NECESSARY USE GLOVES TO
REMOVE THINGS FROM THE DRAWER.
THIS APPLIANCE IS INTENDED FOR DOMESTIC
USE ONLY! FOLLOW THESE INSTRUCTIONS TO
AVOID DAMAGING THE APPLIANCE OR CREATING
DANGEROUS SITUATIONS:
• Do not lean or sit on the warming drawer when opened,
this could cause damage to the telescopic guide. The
maximum carrying weight of the warming drawer is 10kg.
(fig. A)
CLEANING:
• Never use a vacuum cleaner. The vacuum could
create pressure on the components causing a short
circuit. The vacuum may also damage the surface and
the components of the appliance: damages for which the
manufacturer will not be liable.
Grasp the handle
• For cleaning the appliance we recommend following the
suggestions listed under “Cleaning and Maintenance” of
the manual.
REPAIRS:
• ATTENTION! Maintenance work and/or repairs
must be performed exclusively by specialized
personnel. Incorrect installation and maintenance can
cause personal injury to the consumer for which the
manufacturer will not be liable.
(fig. B),
• ATTENTION! During the warranty period, the appliance
may only be serviced by technicians authorized by the
manufacturer or the warranty will be void.
Officine Gullo
Pull the drawer
19
19
5
6. CONTROL PANEL
GB
(fig. C)
towards you until it is opened completely.
4.1 CLOSING THE DRAWER
To close the drawer, gently push the drawer back,
pushing the front until it has completely gone back.
Release the handle.
7. USING YOUR WARMING DRAWER
7.1 Operation
4.2 The appliance is equipped with a hot air ventilating
system. A fan distributes in an optimal way towards the
internal space of the warming drawer.
The thermostat allows the user to control and set the
appliance at the desired temperature.
The circulation of the air heats the drawer in a rapid and
uniform way.
With the protective measures in place it is not possible to
accidentally touch the heating element or the fan.
Open the drawer. Turn the handle in order to set the
desired temperature and then press the red button.
5. BEFORE YOU BEGIN
• Thickness and material of the drawer;
Do not leave parts of the packaging in the
home. Separate the remaining packaging
materials by category and deliver them to
your nearest recycling center.
Before using the appliance for the first time, gently clean
it with a moist cloth and dry it completely as described
under “Cleaning and Maintenance”.
Heat the warming drawer for at least two hours. Once
heated, set the temperature to 75 °C. Be sure that the
kitchen is kept well ventilated during the heating period.
The metal parts have been specially treated with a
protective coating that can sometimes cause odors the
first time the drawer is heated. These odors will quickly
dissipate and should not be considered a defect of the
appliance.
A red light will turn on and will remain on throughout use.
To turn off the appliance, turn the handle to the 0 position
and then press the button. The red light will turn off.
7.2 Heating Time
Different factors influence the time in which it takes to
heat up:
• Number of drawers loaded;
• The arrangement of the loaded drawers;
• The desired temperate set.
So, there is no general rule. To set the temperature
above 60°C in order to have a stable temperature, follow
these suggestions:
~60°C
~40°C
20 20
6
Officine Gullo
DISHES
DISHES FOR 6 PERSONS
TIME (MIN)
30-35
You can also use your own experience in determining
the optimal temperature setting for your needs.
8 CLEANING AND MAINTENANCE
Generally speaking, cleaning is the only form of
maintenance necessary.
Attention! Before you begin cleaning, disconnect the
appliance from the outlet. Disconnect the cord from the
outlet and turn off the appliance.
Warning! Do not use harsh detergents or abrasive
products and/or scrubbing pads and sponges and sharp
objects as they can stain and damage the appearance
of the appliance.
Warning! Never use a vacuum cleaner on the internal
parts of the appliance.
8.1 Front and Panel Commands
The use of a moist cloth is sufficient when cleaning the
appliance. In the event the appliance requires further
cleaning, add drops of detergent in the water. Dry the
appliance with a dry cloth. The steel front of the appliance
can be cleaned with products specifically designed for
steel. Such products prevent the formation of dirt on
the surface of the drawer. Apply a minimal amount of
the product on a soft and apply it to the surface of the
appliance.
8.2 Inside Space
To clean the inside space use a moist cloth. In the event
the appliance requires further cleaning add drops of
detergent to the water. Dry the surface with a dry cloth.
Make sure to avoid water draining into the ventilation
holes. Only use the appliance after the drawers are dry
completely.
Attention! During cleaning, do not wash the external parts of
appliance with direct sprays of water or with high pres9the
TROUBLESHOOTING
sure.
After every use, clean the appliance thoroughly. Daily cleaning after switching
off the
appliance
ensures
the perfect
ATTENTION!
Repairs
must
only be
performed
by
functioning and
life of the
appliance.Any repair work
specialized
andlong
qualified
personnel.
Before
starting toby
clean
the appliance,
disconnect
thecause
power
not
performed
professional
personnel
may
supply. The
parts
in steel for
must
be washed
with hot water
damage
to the
appliance
which
the manufacturer
will
andbe
neutral
detergent, then rinsed thoroughly in order to elinot
liable.
minate
all traces
of detergent;
after
which,
with a dry
The
following
problems
can be
fixed
by dried
the consumer
cloth. Dothe
notassistance
use abrasive
or corrosive
detergents.
without
of the
Service Department.
CLEANING BURNISHED BRASS SURFACES
No synthetic protective varnishes have been used to
obtain the special burnishing effect on the burnished
brass details in order to avoid spoiling the beauty of the
brass with an artificial patina. The antique finish of the
The
drawer
is not
hotofenough.
surethat
that:has simply
surface
is the
result
natural Make
oxidation
been accelerated. All the natural antique finish brass
•surfaces
The appliance
turned on;
can beiscleaned
with any kitchen degreasing
•detergent,
The correct
temperature by
hasthe
been
set;of an abrasive
accompanied
use
•scouring
The opening
of
the
ventilation
fan is
notfor
blocked
by
pad (the green colored type
used
washing
plates orIt other
large obstructions;
dishes).
is recommended
that the metal be rubbed,
•uniformly
The drawers
havelight
hadpressure,
sufficientuntil
timethe
to desired
heat up.effect
applying
is achieved.
The
is not hot
at all.
Make
sure that:
The drawer
brass details
should
then
be dried.
•Do
You
fan running;
nothear
usethe
polish
as this is suitable for maintaining
•the
If the
turned
on this finish
means
theresult
heating
glossfan
butisnot
the antique
andthat
could
in
working;
ansystem
effect is
that
is not compliant with our products. Any
•spots
If the that
fan does
work over
this means
it isthe
defective;
may not
appear
time on
burnished
•brass
The circuit
fuseshould
is blown.
surfaces
be considered as a desirable
and particular characteristic of our craft metal working
processes.
10 APPLIANCE INSTALLATION
CLEANING
CHROMIUM-PLATED
BRASS
10.1 Before
you begin
installation
SURFACES
Make
sure thatvarnishes
the voltage
shown
onused
the appliance
No synthetic
have
been
to obtainlabel
the
corresponds
to that
of your
electrical system.
special polish
on the
chromium-plated
brass details
Open
theto drawer
and remove
all of
accessories
and
in order
avoid spoiling
the beauty
the chromium
packing
materials.
plating with
an artificial patina.
Attention!
The front of the
drawer
may be
be cleaned,
covered
All the chromium-plated
surfaces
should
with
a necessary,
protective coating
overpossibly
it. Carefully
remove
the
where
with a soft,
micro-fiber
cloth,
coating
before
using polishing
the appliance.
Start
by removing
combined
with metal
products,
if required.
Do
the
protective
film
from the bottom. Make sure that
not use
abrasive
pads.
the drawer is not damaged. Be certain that the drawer
closes properly. In case of damage, contact the Service
CLEANING SATIN FINISH NICKEL-PLATED BRASS
Department.
The warming drawer can
only be attached and installed
SURFACES
with
the tools varnishes
provided by
thebeen
appliance
No synthetic
have
used manufacturer.
to obtain the
The
manufacturer
does
thenickel-plated
operation of
special
nickel-plating
onnot
theguarantee
satin finish
the
appliance
materials
fromspoiling
a different
manufacturer
brass
details inif order
to avoid
the beauty
of the
have
been used.
The
manufacturer
is notwith
responsible
for
nickel-plated,
satin
finished
solid brass
an artificial
damage
patina. caused by improper use.
All the nickel-plated and satin finished brass surfaces
should be cleaned, where necessary, with a soft,
10.2
Proceed
possibly
micro-fiber cloth, combined with a neutral
detergent, if required. Do not use abrasive pads.
Before you begin assembling the drawers of the
appliance, make sure there is enough room to fit the
CLEANING THE VARNISHED SURFACES
drawer and the appliance.
All the varnished surfaces should be cleaned using a
neutral detergent and, where necessary, a soft, possibly
The precise dimensions for the installment are indicated
micro-fiber cloth. Do not use abrasive pads or any other
in mm. Follow these guidelines for assembly:
chemical products.
• Position the drawer so that it is directly centered
BRUSHED
SURFACES
• Be CLEANING
certain that the
frame isSTEEL
perfectly
perpendicular
the brushed
steeland
surfaces
be to
cleaned
using
•AllOpen
the drawer
fix theshould
structure
the wall
with
degreasing
products
or products
the two screws
already
in place specifically designed
to beElectrical
used on Installation
steel and, where necessary, extra-fine
10.3
steel wool or extra-thin sandpaper.
The electrical connection must be made by a qualified
electrician conforming to current regulations.
21 21
Officine Gullo
GB
7
9 TROUBLESHOOTING
ATTENTION! Repairs must only be performed by
specialized and qualified personnel. Any repair work not
performed by professional personnel may cause damage
to the appliance for which the manufacturer will not be
liable.
The following problems can be fixed by the consumer
without the assistance of the Service Department.
The drawer is not hot enough. Make sure that:
• The appliance is turned on;
• The correct temperature has been set;
• The opening of the ventilation fan is not blocked by
plates or other large obstructions;
• The drawers have had sufficient time to heat up.
The drawer is not hot at all. Make sure that:
• You hear the fan running;
• If the fan is turned on this means that the heating system
is working;
• If the fan does not work this means it is defective;
• The circuit fuse is blown.
10 APPLIANCE INSTALLATION
10.1 Before you begin installation
Make sure that the voltage shown on the appliance label
corresponds to that of your electrical system.
Open the drawer and remove all accessories and packing
materials.
Attention! The front of the drawer may be covered
with a protective coating over it. Carefully remove the
coating before using the appliance. Start by removing
the protective film from the bottom. Make sure that
the drawer is not damaged. Be certain that the drawer
closes properly. In case of damage, contact the Service
Department.
The warming drawer can only be attached and installed
with the tools provided by the appliance manufacturer.
The manufacturer does not guarantee the operation of
the appliance if materials from a different manufacturer
have been used. The manufacturer is not responsible for
damage caused by improper use.
10.2 Proceed
Before you begin assembling the drawers of the
appliance, make sure there is enough room to fit the
drawer and the appliance.
The precise dimensions for the installment are indicated
in mm.
Follow these guidelines for assembly:
• Position the drawer so that it is directly centered
• Be certain that the frame is perfectly perpendicular
• Open the drawer and fix the structure to the wall with the
two screws already in place
10.3 Electrical Installation
The electrical connection must be made by a qualified
electrician conforming to current regulations.
8
Electrical connections
Before connecting the oven to the mains power supply,
make sure that: - The supply voltage corresponds
to the specifications on the data plate on the front of
the oven. - The mains supply has an efficient earth
(ground) connection complying with all applicable laws
and regulations. Correct earthing (grounding) is a legal
requirement. The power cable should never reach a
temperature 50° C above ambient temperature at any
point along its length. If a fixed appliance is not provided
with a power cable and plug, or some other device
permitting it to be disconnected from the mains electricity
supply, with a gap between the contacts big enough to
guarantee class III overvoltage protection, then such a
device must be fitted to the power supply in compliance
with the regulations governing electrical installations.
The socket or switch must be easily reachable with the
oven fully installed.
CABLE TYPES AND MINIMAL DIAMETERS
SASO
H05RR-F 3x0,75 mm²
H05RR-F 3x1,5 mm²
H05VV-F 3x0,75 mm²
H05VV-F 3x1,5 mm²
H05RN-F 3x0,75 mm²
H05RN-F 3x1,5 mm²
H05V2V2-F 3x0,75 mm²
H05V2V2-F 3x1,5 mm²
WARNING! Before connecting the warming drawer
to the electrical circuit, verify that the voltage and the
frequency correspond to those indicated on the label
located inside the heating block, which should be kept
along with this manual.
The electrical attachment must be made using bipolar
switch capable of powering the appliance and that has
a gap of 3 mm (minimum) to guarantee disconnection
in case of emergency or when cleaning the warming
drawer.
Connect the appliance to the ground circuit to conform to
safety regulations regarding electrical systems.
ATTENTION! THE WARMING DRAWER MUST BE
CONNECTED TO THE GROUND CIRCUIT.
In the event of the failure of the cable supplied with the
warming drawer, replace it with an original replacement
part provided by the Service Department.
The manufacturer and retailers will not be liable for
property damage and personal injury caused by a failure
to follow the instructions provided in this manual.
Officine Gullo
27
Officine Gullo
9
en
INTERNATIONAL
V 1.0 - 03.2017
OFFICINE GULLO S.R.L.: via della Torricella 29, 50012 Antella - Bagno a Ripoli (FI)
Tel. +39 055 6560324 / 621807 - Fax: + 39 055 620670 - info@officinegullo.com
WWW.OFFICINEGULLO.COM
Download PDF
Similar pages