Limited Lifetime Warranty
Water Decor Inc. provides limited lifetime warranty to the original purchaser on all mechanical parts
to be free from manufacturing defects in material and workmanship under normal use.
If any material proves to be defective after inspection by Water Decor Inc. it will, at its’ election
repair, replace, or make appropriate adjustments at our discretion at no additional charge. However,
no claims for labor, shipping costs, or consequential damages will be accepted. Water Decor Inc. is
not responsible for removal or installation costs.
This warranty applies only when goods are used for purposes and conditions for which they are
intended. This warranty is voided by improper installation or by any modification or alteration of
Water Decor Inc. products.
Finish Warranty: A limited lifetime warranty is provided on all Water Decor Inc. product finishes to
the original purchaser against manufacturing defects in material and workmanship. Use of any lead
based or acidic curing sealant or the use of acids, abrasives or detergents to clean Water Decor Inc.
products will void the finish warranty. Use only sealants which are natural curing and not reactive
with metal or brass finishes.
The responsibility of Water Decor Inc. shall not exceed the purchase price of the item.
To obtain warranty service, contact the dealer that the product was purchased through.
To the extent permitted by law, all implied warranties, including those of merchantability and fitness
for as particular purpose, are hereby disclaimed. Water Decor Inc. disclaims all liability for special,
incidental, or consequential damages.
This warranty gives you specific legal rights. You may also have other rights which vary from state to
state.
This is our exclusive written warranty.
03302-090
03302-292
03302-393
Bridge 8” Widespread Lavatory Faucet
waterdecor
INSTALLATION GUIDE
This product meets ANSI/NSF Standard 61, Sect. 9, Safe Drinking Water
Act - lead content and leaching
We at Water Decor believe that the beauty of our faucets should last a lifetime. That is the reason
we only use polished chrome and PVD finishes. With minimal care your Water Decor faucet will look
terrific for years to come.
It helps if the product is wiped down with a soft towel after each use to prevent water spotting and
mineral deposit build up.
The faucets can also be cleaned with a non-ammoniated spray cleaner or mild soap and water.
waterdecor
3579 East Foothill Boulevard • Suite 418
Pasadena • California 91107
Tel: 877.222.9644 • Fax: 626.744.0377
E-mail: info@waterdecor.com
Copyright © MMVI Water Decor Inc. All Rights Reserved
03302-494
IMPORTANT
SHUT OFF WATER SUPPLY BEFORE BEGINNING
INSTALLATION
HOW TO REPLACE CARTRIDGE
stem
It’s important to shut off the main water supply before
disassembling. Hire experienced, certified plumber
is strongly recommended. If you have any questions,
please call us at (877) 222-9644 for assistance.
Blue for Cold
Red for Hot
TOOLS NEEDED :: 12” pipe wrench, large adjustable wrench.
Be sure to have the right cartridge. The cartridge for
cold side is coming with a blue sealing washer at the
bottom of it, whereas the one for hot side is coming
with a red sealing washer.
Remove the handle by turning the escutcheon cap counterclockwise and pull it off.
Unscrew the old cartridge off by using an adjustable wrench. Install the correct
cartridge at the correct location, cold at left and hot at right. Use the adjustable
wrench to tighten the cartridge, but be aware not to overtighten it.
IMPORTANT PLEASE READ INSTRUCTION BEFORE INSTALLATION
SHUT OFF WATER SUPPLY BEFORE BEGINNING INSTALLATION!
THE SPOUT ASSEMBLY IS HEAVY, PLEASE HANDLE WITH CARE.
Before putting the handle back, turn on water supply to test. Use hand or the
handle, without screwing it on, to turn the stem for a fully open & a fully close
position and make sure the new cartridge works well.
THIS IS A SPACE-LIMITED JOB, ALWAYS WEAR GOGGLE AND WATCH FOR
POSSIBLE FALLING OBJECTS THAT MAY CAUSE PARTS DAMAGE OR BODY INJURY.
Fully closed position
DO NOT USE PIPE WRENCH ON FINISHED SURFACES.
DO NOT USE ANY “PLUMBERS PUTTY” OR ANY OIL BASED SEALANT. USE OF
ANYTHING OTHER THAN SILICON SEALANT MAY DISCOLOR THE SURFACE AND
WILL VOID THE FINISH WARRANTY.
Escutcheon
Cap
Make sure the cartridge is at its fully
close position and put the handle
back on. Align the two handles
horizontally. Gently push the handle
in and turn the escutcheon cap
clockwise by hand.
It is a good idea on new construction to pull the aerator and flush the lines.
1 :: Install Pop-Up Base
Counter Top
or Sink
To clean the aerator insert a large flat bladed screwdriver into the slot on the
aerator housing and turn counter clockwise to remove.
Pop-Up Knob
Unscrew the nut from the pop-up base.
Pop-Up Base
Locate the center hole on the sink or counter top.
Rinse out the screen and any debris in the housing.
Replace the rubber washer, aerator and housing making sure that the notch in the
housing is pointing straight down when finished.
Insert the pop-up base from the top through the
center hole. Tighten the nut from the bottom of the
pop-up base. Insert the pop-up knob into the
pop-up base.
Nut
2 :: Install the Drain into Sink
Take out drain stopper and keep it aside.
Spout
Rubber Washer
Faucet Aerator
Aerator Housing
Unscrew the drain from the drain assembly. Keep the flange washer in place.
Remove the cone rubber washer, plastic washer,
and unscrew the nut off.
Flange
Washer
Install drain with flange washer from the top of the
sink into the hole of the sink.
Place cone rubber washer back from the bottom of
the drain. Make sure the cone shape is upward and
is inserted evenly, without any jerks, into the back
hole of the sink.
Put on the plastic washer and tighten the nut to
secure the drain.
Drain
Sink
Cone
Plastic
Rubber
Washer
Washer
Nut
Pop-Up
Connector
Tailpiece
Unscrew the tailpiece off from the pop-up
connector. And insert the tailpiece into the drain pipe (not included).
Install the pop-up connector by connecting it, onto the bottom of the drain (DO
NOT OVERTIGHTEN). Make sure the hole, which is for assembling with pop-up ball
rod, is facing backward. Adjust by loosing the nut if necessary.
Slide up the tailpiece and connect it to the pop-up connector. Secure all the drain
connections.
Insert drain stopper from top of the sink
into drain.
Unscrew the small nut from drain, insert
ball rod in. Make sure that the short end
of ball rod fits in the stopper eye-screw
hole.
Stopper’s
Eye-Screw
Small Nut
Ball Rod
Put the small nut back and tighten it up,
NOT over tight. Be sure that ball rod
must be moved up and down freely.
Spout
1-1/4” Hole
Assembly
Connect ball rod and lift rod by inserting
lift rod into ball rod’s clamp lock. Adjust
to the appropriate height and then tighten the clamp lock’s screw.
Size
Pop-Up
Pop-Up Knob
Escutcheon
NOTE: It may be necessary to cut the length of the “Ball Rod” if it is too close to
the wall or cabinet.
Mounting Nut
Shank
Mounting Nut
Shank
3 :: Install Spout Assembly
Install faucet body into 8” center holes. CAUTION!!! The spout is heavy. Please
handle with care.
Install and tighten both nuts on the bottom of the faucet body. Connect supply
hoses to faucet body (supply hoses are not included). Connecting the other end of
the hoses to the water supply valves.
Download PDF
Similar pages