BRETFORD BASICS ™
CONNECTIONS SMARTDECK ™
The Connections Smart Deck Work Centers were
specifically designed to accommodate a flat screen
computer monitor. These tables are great for
classroom use since the monitors open and close into
the desktop. When closed, desk top is flat for
classroom use. Tops are finished in grey laminate with
trim available in four different colors. Bases are
constructed of steel and finished in grey powder
paint.
35SD25-GMQ
FEATURES
• Tables are great for classroom or training applications because they can be used for computer work and close the flat screen down into
desktop and you now have a flat work surface to work on.
• Large work surface neatly flips open to reveal one flat screen monitor up to 19" diagonal, see specs for monitor case size requirements. Two
monitors are supported on the 66"W and 72"W tables.
• Flat screen compartment folds down and flush with the top for a flat writing work surface. Monitor compartment locks when closed flush into
the desk top.
• Work surfaces are constructed of 1” thick MDF covered with Grey Mist high pressure laminate with Quartz grey PVC trim (other trim colors
also available including Cardinal red, Polo green and Topaz blue). Laminate substrait consists of an average 70% recycled content. Special
order laminate and paint colors are available.
• Complies with the GREENGUARD Environmental Institute’s GREENGUARD Children & Schools Indoor Air Quality standards, contributing to
points toward Leadership in Energy and Environmental Design (LEED) Certification.
• Bases are constructed of 18- and 14-gauge steel tubing which consists of an average 30% post-consumer recycled content and finished in an
environmentally friendly grey powder paint which withstands years of use
• Adjustable in one inch increments from 24" to a 32" high clearance to meet ADA approval.
• The Smart Deck Work Centers are available in 36”w for one computer and 66"w or 72”w for two computers. The overall depth is 24”.
• Tables include a 4 outlet electrical unit with 20' power cord.
• Includes a CPU harness which mounts to the inside or outside of either leg, 66" and 72" wide tables include two CPU holders. Standard CPU
holder is adjustable for computers 6"-111/2"W. Slim CPU holder is adjustable for computers 3-1⁄2"-5-7/8"W. Note: When CPU harness is mounted
on the inside of leg the height is limited. For example when height of table is set at 29”h, the maximum height the CPU’s can be set at is 17"h.
• A cord management bin also acts as a modesty panel which runs the entire width of the table under the work surface.
• Tables come with adjustable leveling glides.
OVERALL DIMENSIONS
MONITOR AND KEYBOARD BIN SPECIFICATIONS
35SD21 & 35SD21MT: 36"w x 24"d x 24-32"h
SmartDeck is designed to hold most flat panel monitors up to 19"
35SD27 & 35SD27MT: 66"w x 24"d x 24-32"h
diagonal, dependent upon the monitor case dimensions. The monitor
35SD25 & 35SD25MT: 72"w x 24"d x 24-32"h
mounts to the underside of the work surface door using 75mm or
100mm VESA compliant mounting holes. VESA compliant mounting
COLOR/FINISH
holes must be located at or in the approximate center of the case
Base/Tabletops: Grey powder paint/Grey laminate
and may not be recessed more than 1/4" into the case. Longer
Trim, Toe Caps & Grommet Holes: Available in Cardinal (GMC),
mounting screws may be required for monitors with recessed holes.
Topaz (GMT), Polo (GML) and Quartz (GMQ)
SmartDeck will work with most monitors to 19" but specific models
must be pre-tested to guarantee compatibility. For general guidelines
SmartDeck supports monitor cases that are up to 20"w x 14"h and
are not more than 4"d when combined with the keyboard. Monitors
with VESA compliant mounting holes located only at the bottom of
CARDINAL - C QUARTZ - Q
POLO - L
TOPAZ - T
the case will not work with SmartDeck. The keyboard and mouse
store inside the bin when closed on a retractable surface. The mouse
STANDARD EQUIPMENT
must be stored next to, not on top of, the keyboard when closed.
Table top (1)
Monitor bins key lock closed for security, all tables are keyed alike
Right leg assembly (1)
Left leg assembly (1)
SUGGESTED SPECIFICATIONS
Cord management bin/modesty panel (1)
35SD21, 35SD21MT, 35SD27, 35SD27MT, 35SD25 & 35SD25MT are
Surge Protected 4-Outlet Electrical Unit (1)
height adjustable from 24-32" in 1" increments. The width is 36"w,
CPU Harness 36" units have (1); 66" and 72"w units have (2)
66"w or 72"w depending on the model. Table top is constructed from
Adjustable floor glides (4)
1" thick MD covered with high pressure laminate with 3mm PVT trim.
The modesty panel/cord management bin is made from 18-gauge
CARTON UPC CODES
steel. It runs the width of the table. The legs are constructed from 18-
35SD21-GMC - 0 96633 23734 0
35SD21MT-GMC - 0 96633 30578 0
and 14-gauge steel tubing. The CPU Harness is constructed from steel
35SD21-GML - 0 96633 23735 7
35SD21MT-GML - 0 96633 30579 7
and mounts on the inside of either leg. 36"w model comes with one
35SD21-GMQ - 0 96633 23736 4
35SD21MT-GMQ - 0 96633 30580 3
CPU Harness and the 66"w and 72"w model comes with 2. Standard
35SD21-GMT - 0 96633 23737 1
35SD21MT-GMT - 0 96633 30581 0
CPU harness adjusts 6"-11-1⁄2"w and slim CPU harness (MT models)
35SD27-GMC - 0 96633 30503 2
35SD27MT-GMC - 0 96633 31236 8
adjusts 31⁄2"-5-7⁄8"w. All steel parts are constructed with “prime” steel
35SD27-GML - 0 96633 30504 9
35SD27MT-GML - 0 96633 31237 5
which has a 25% to 35% post-consumer recycled content and are
35SD27-GMQ - 0 96633 30505 6
35SD27MT-GMQ - 0 96633 31238 2
finished in an environmentally friendly powder paint. Table shall be
35SD27-GMT - 0 96633 30506 3
35SD27MT-GMT - 0 96633 31239 9
GREENGUARD INDOOR AIR QUALITY CERTIFIED®. Ship ready to
35SD25-GMC - 0 96633 23738 8
35SD25MT-GMC - 0 96633 30582 7
assemble.
35SD25-GML - 0 96633 23739 5
35SD25MT-GML - 0 96633 30583 4
35SD25-GMQ - 0 96633 23740 1
35SD25MT-GMQ - 0 96633 30584 1
MADE IN THE USA
35SD25-GMT - 0 96633 23741 8
35SD25MT-GMT - 0 96633 30585 8
All Connections series tables are made at one of Bretford’s Chicago
area manufacturing facilities using union labor.
CARTON DIMENSIONS
35SD21 & 35SD21MT:
40"l x 28"w x 20"d
122 lbs., 6.286 cubes, Freight Class 70
35SD27 & 35SD27MT:
76"l x 28"w x 20"d
195 lbs., 12.015 cubes, Freight Class 70
35SD25 & 35SD25MT:
76"l x 28"w x 20"d
202 lbs., 12.015 cubes, Freight Class 70
11000 SEYMOUR AVENUE
FRANKLIN PARK, ILLINOIS 60131 USA
TOLL FREE PHONE 800-521-9614
PHONE 847-678-2545
TOLL FREE FAX 800-343-1779
FAX 847-678-0852
WWW.BRETFORD.COM
©2004 Bretford / b_connect_smart_deck / 07.08
35SD21-GMQ
Download PDF
Similar pages