®
OPERATION AND MAINTENANCE MANUAL
BSD-B6120L
BSD-B6190L
BSD-B6120LF
BSD-B6120P
BSD-B6190P
BSD-B6120PF
LOW VOLTAGE
DC-TYPE Automatic Non Carbon-Brush Series
WWW.KILEWS.COM.CN
KILEWS ELECTRIC TOOLS（SHANGHAI）CO., LTD.
No.367, 2nd Xinjian Road, Xuhang Town, Jiading District, Shanghai 201808 China
Tel: 86-21-59556022
Fax: 86-21-59553779
Y20066
BSD-B6000L/P SERIES
NOTICE
Metal Assembly Screwdrivers are designed for installing threaded fasteners in light industrial
and appliance manufacturing applications.
KILEWS is not responsible for customer modification of tools for applications on which
KILEWS was not consulted.
WARNING
Important safety information enclosed.
Read all these instructions before placing tool in service or operation this tool and save
these instructions. It is the responsibility of the employer to place the information in this
manual into the hands of the operator. Failure to observe the following warnings could result
in injury. When using electric tools, Basic safety precautions should always be followed to
reduce the risk of fire, electric shock and personal injury, including the following:

BSD-B6000L/P SERIES
1. Important Safety Rules
2. Grounding Instructions
3.Operations Cautions
4.Description of Operation
5.Servicing
6.Specifications
7.Accessories
8.Torque Adjustment Operation

BSD-B6000L/P SERIES
1.Important Safety Rules
WARNING! Read all instructions Failure to follow all instructions listed below may result in
electric shock fire and/or serious injure. The term “power tool” in all of the warning listed
below refer to your mains operated (corded) power tool or battery operated (cordless) power
tool.
SAVE THESE INSTRUCTIONS
1) Electrical Safety
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmosphere, such as in the presence of
flammable liquids, gases or dust. Power tools creat sparks which may ignite the dust
of fumes..
c) Keep children, and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) Electrical Safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
c) Don’t expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord to carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use.Use of cord suitable for outdoor use reduces the risk of electric shock .
3) Personal Safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use power tool while you are tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may
result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
Rubber gloves and non-skid footwear are recommended when working outdoors.
c) Avoid accidental starting. Ensure the switch is in the off position before plugging in.
Carrying power tools with your finger on the switch or plugging in power tools that have
the switch on invites accidents.
d) Remove any adjusting keys or wrench before turning the power tool on. A wrench or
a key that is left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,clothing,
and gloves away from moving parts. Loose clothes, jewellery, or long hair can be

BSD-B6000L/P SERIES
caught in moving parts
g) Secure work.Use clamps or a vice to hold the work. It is safer than using your hand and
frees both hands to operate the tool.
h) If devices are provided for the connection of dust extraction and collection facilitys,
ensure these are connected and properly used. Use of these devices can reduce dust
related hazards.
4) Power tool Use and Care
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use power tool if switch does not turn it on or off. Any power tool that cannot
be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing the power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
Do not let visitors touch the tool or extension cord. All visitors should be kept away from
work area.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tools operation. If
damaged, have the power tool repaired before use. Many accidents are cause by
poorly maintained power tools.
Inspect extension cords periodically and replace, if damaged.
f) Keep cutting tools sharp and clean, Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tools, accessories and tool bits ect., in accordance with these
instructions and in the manner intended for the particular type of power tool, taking
into account the working conditions and the work to be performed. Use of the power
tool for operations different from intended could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by qualified repair person using only indentical
replacement parts, This will ensure that the safety of the power tool is maintained.
Additional information shall be provide
a) Instruction for putting into use
1. Setting-up or fixing power tool in a stable position as appropriate for power tools which
can be mounted on a support.
2. Assembly
3. Connection to power supply, cabling, fusing, socket type and earthing requirements.
4. Illustrated description of functions.
5. Limitations on ambient conditions.
6. List of contents.
b) Operating Instructions.
1. Setting and testing.
2. Tool changing.
3. Clamping of work.
4. Limits on size of work piece.
5. General instructions for use.
c) Maintenance and servicing.

BSD-B6000L/P SERIES
1. Regular cleaning, maintenance, and lubrication.
2. Servicing by manufacture or agent, list of addresses.
3. List of user-replaceable parts.
4. Special tools which may be required.
WARNING！
DO NOT OPERATE THIS TOOL WITHOUT
PROTECTIVE EARTH CONNECTED
2.Grounding Instructions
1. This tool should be grounded while in use to protect the operator from electric shock.
NOTICE ! To ensure the grounding result, the grounding conductor of the power cord
must be well connected with the grounding terminal of power facility. This tool is
equipped with grounding conductors. The Green(or Green and Yellow)conductor in the
Power Cord is the grounding wire. Never connect Green (or Green and Yellow) to a live
terminal. The grounding wires in this tool can not only earth the electric leakage safely,
but also can eliminate ESD-the electrostatic that tool occurred while in use.
2. The grounding is the most important task a user. Periodically, depends on the working
condition and circumstance, for maintaining a good function the user has to check the
grounding condition every 3~6 months by an electric meter and following simple steps;
Set the Ohm meter to level R*100(Ohm). Touching 2 test rods (“＋”＆”－”) together and
reset the meter to “0”. Using the Red(“＋”) rod to touch the Grounding wire on the Plug
of controller’s cord, and the Black(“－”) rod to the end of Bit Head. It stands for the
grounding is normal if the meter is read as close as to “0”. For getting a normal
indication on the meter while in testing, need to press the test rods firmly to the testing
objects.
3. The instrument QC of the tool is performed before the tool ex-factory. The grounding
continuity test is conducted by input 8A voltage to the end of earth terminal, and subject
to the resistance value lower than 0.3Ohm.

BSD-B6000L/P SERIES
3.Operations Cautions
1) Whenever changing a bit, make certain the Forward / Reverse Switch is in the “ OFF
“ position and tool is unplugged.
2) Do not allow chemicals such as acetone, benzene, thinner, trichloroethylene ketone, or
other similar chemicals to come in contact with the screwdriver housing as damage will
result.
3) Do not drop or abuse the screwdriver.
4) Do not adjust the torque setting higher than 8 on the torque scale.
5) There should be a tool rest interval when cycles three seconds or longer. This tool is
intended for a duty cycle of 0.8 sec on, 2.4 sec off.
6) Do not use this screwdriver for tightening wood screws. This is “ Metal Assembly Screw
Driver ”
7) Do not operate the Forward / Reverse Switch the motor is running.
8) Whenever a tool is not being used, move the Forward / Reverse Switch to the “OFF”
position and unplug the screwdriver.
9) Don't touch For&Rew Switch during operating for keeping system from wrong
judgement.
CAUTION
● Do not drop or abuse the tool.
● Whenever a tool is not being used, position the Power Switch to the “OFF” position and
unplug the power cord.

BSD-B6000L/P SERIES
4.Description of Operation
Attaching / detaching bit and bit type
Push up the holder clamp by finger tip, and it will be unlocked. Thus, the bit can be freely
attached and detached (single finger notion type) select such a bit whose shank is equal to
the size shown below.
 Insert the power plug into a receptacle and set the changeover switch to “F” position.
 Apply the bit to the screw head and press the lever or push main body to, then the



switch will be turned ON to start the motor running.
When the screw is tighten and reach the torque that you had set, The tool will stopped
automatically.
To reset the tool by releasing the lever to the original position or releasing the bit From
the screw head.
To return the screw, set the changeover switch to “R” position.
5.Servicing
Maintenance and Inspection:
1. The screw driver must be operated in top condition, one day working hour must be
not more than eight hours.
2. Please note don’t let the motor get over heated, every minute use 10~15 screws to
operate.
3.The frequency use of this electric screw driver is over than eight hours a day, still it needs
periodically testing and treatment. Every 5-6 months.
4.Inspect tool cords periodically and if damaged, have them repaired by an authorized
service facility. Inspect extension cords periodically and replace if damaged.
5.Do not remove any labels. Replace any damaged label.

BSD-B6000L/P SERIES
CAUTION
1. The use of other than genuine KILEWS replacement parts may Result in decreased
tool performance and increased maintenance, and may invalidate all warranties.
2. All repairs and maintenance of this tool and its word must be performed by an authorized
service center.
3. KILEWS is not responsible for customer modification of tools for applications on which
KILEWS was not consulted.
4. Repairs should by made only by authorized, trained personnel. Consult your nearest
KILEWS authorized service center.
5. It is the responsibility of the employer to place the information in this manual into the
hands of the operator.
DO NOT ATTEMPT TO REPAIR THIS
ELECTRIC SCREW DRIVER
CAUTION
SAVE THESE INSTRUCTIONS
DO NOT DESTROY

BSD-B6000L/P SERIES
6.Specifications
MODEL
BSD-B6120L BSD-B6190L BSD-B6120LF BSD-B6120P BSD-B6190P BSD-B6120PF
Input voltage(DC)
DC 24V OR 32V
DC 32V
Power Consumption
DC 24V OR 32V
55W
(kgf.cm)
1.5-12
3-19
1.5-12
2-12
3-19
2-12
(Lbf.in)
1.32-10.44
2.56-16.46
1.32-10.44
1.68~10.44
2.56-16.48
1.68~10.44
(N.m)
0.15-1.18
0.29-1.86
0.15-1.18
0.19~1.18
0.29-1.86
0.19~1.18
Torque
Repeatable Torque Accuracy
(%)
±3%
Torque Adjustment
Stepless
Unloaded Rotation
Speed
(r/min)±10%
Screw Size Dia
HI
1000
1000
2000
1000
1000
2000
LO
700
700
-
700
700
-
Machine
screw(mm)
1.6~3.0
2.3~3.5
1.6~3.0
1.6~3.0
2.3~3.5
1.6~3.0
Tapping
screw(mm)
1.6~2.6
2.3~3.0
1.6~2.6
1.6~2.6
2.3~3.0
1.6~2.6
Weight (g)
Length
DC 32V
520
(mm)
245
Model of Torque Fixing Ring
KC-6C/KC-6S
Power controller
BSP-32D-60W
Model of Suspension Rack
KH-4(KC&KH-2)
Bit Type
HEX 5mm,
HEX 6.35mm
Ø4mm,
* 1N.m=10.2Kgf.cm
Ø5mm
1N.m=8.85Lbf.in
7.Accessories
1. BIT Type： No. 00 ．．． Bit use in dia 1.3~1.8mm screw
No. 0．．．． Bit use in dia 1.6~2.0mm screw
No. 1．．． ．Bit use in dia 2.0~2.6mm screw
No. 2．． ．．Bit use in dia 3.0~4.0mm screw
BSD-B6120L ；BSD-B6120P
with BIT
1# & 2#
1 Pcs. Each
BSD-B6190L ；BSD-B6190P
with BIT
1# & 2#
1 Pcs. Each
BSD-B6120LF ；BSD-B6120PF
with BIT
1# & 2#
1 Pcs. Each
2. Suspension rack and Torque fixing ring acceptable for use with the tool are available from
KILEWS catalogue.
3. Spring 1 Pcs
es

BSD-B6000L/P SERIES
8.Torque Adjustment Operation
To adjust the torque on these screwdrivers. Proceed as
follows :
1. Determine the torque output of the tool by checking a
tightened Fastener with a torque wrench.
2. Increase or decrease the torque by rotating the Spring
Adjusting Ring. Rotating the Ring clockwise to a
higher number on the torque Scale increase torque
output while rotating the Ring counterclockwise to a
lower number decreases the torque output.
3. Check the adjustment with a torque wrench. A
number of factors will affect torque output from one
job to another. Final torque adjustment should be
made at the job through a of series of gradual
increase. Always start below the desired torque and
work upward.
4. Adjust the bit torque by changing the driving in length
of the adjust ring at the end.
5. The relationship between torque scale and bit torque
is as shown Ring, in the torque diagram. The figures
of torque scale do not indicate bit torque values.
However, the clamping torque of screw itself is different form type, size, material of the
screw and the material of its mating part. Use it as standard to obtain an appropriate
clamping torque.
6. The (Return torque method) in which once-clamped screw is returned with torque
wrench or the like is available as one of torque control methods however, note that the
measured values by the return torque method generally appear in 10%~30% lower than
the actually clamping torque.
7. The torque checker measures the torque of screwdriver. The clamping torque of screw
itself is different from the clamped conditions. Understand the correlation between
clamping torque values and the torque checker values perform the torque control
properly.
CAUTION
1. Also in reverse rotation, the clutch is turned off in such manner as in normal rotation,
stopping the motor running. Accordingly, when the screw tightened at a large torque, set
it to a higher torque scale.
2. The number from zero to eight on the Torque Scale are reference number only and not
an indication of actual torque output.
3. The power supplier will generate low power when the button of the power controller is
switched to "LO." Also, the electric screwdriver's torque output setting value should be
adjusted to middle torsion value accordingly.

B6120L
NO
1
2
3
4
PARTS NO
AA50001-26N
AA50001-62N
CJ20011
CC50016
CC50016-1
5 CB50230-6
CB50230-7
6 CA50230-6
CA50230-7
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
CE50152-3
CE80001
CH30200
H10204
CC28028-2
CC28028-3
EG31420
EG31414-4A
CH90154
CH20510
CH20102
MI90302
CH20102-24
MO50113
M11322-1
MG91081
GZ51901-1A
GZ51901-1B
GZ51901-1C
GZ51901-1D
GZ51901-1AD
GZ51901-2A
GZ51901-2B
GZ51901-2C
GZ51901-2D
GZ51901-2AD
MI31221
MI33241
GK20231
GI20251-1
GH20241
GG20271
G20101
GH20241
GG20271
GA91284
GN30321
PARTS NAME-E
CORD ASSEMBLY
CONNECTOR
SUSPENSION RING
TRIGGER ASSEMBLY
TRIGGER ASSEMBLY-ESD
HOUSUNG-UNDERSIDE
HOUSUNG-UNDERSIDE-ESD
HOUSING-UPSIDE
HOUSING-UPSIDE-ESD
PUSH ROD
FIXTURE
SCREW
CHANGEOVER SWITCH
TRIGGER ASSEMBLY FOR B6120L
TRIGGER ASSEMBLY FOR B6190L
PCB
P.C.B
SCREW FOR PCB
SCREW FOR ESD TYPE
SCREW FOR HOUSING
PILOT ROD
SCREW FOR MOTOR
MOTOR ASSEMBLY
GEAR
PILOT ROD
CLUTCH ASSEMBLY FOR "BSD-B6120LA"
CLUTCH ASSEMBLY FOR "BSD-B6120LB"
CLUTCH ASSEMBLY FOR "BSD-B6120LC"
CLUTCH ASSEMBLY FOR "BSD-B6120LD"
CLUTCH ASSEMBLY FOR "BSD-B6120LAD"
CLUTCH ASSEMBLY FOR "BSD-B6190A"
CLUTCH ASSEMBLY FOR "BSD-B6190LB"
CLUTCH ASSEMBLY FOR "BSD-B6190LC"
CLUTCH ASSEMBLY FOR "BSD-B6190LD"
CLUTCH ASSEMBLY FOR "BSD-B6190LAD"
PILOT ROD FOR"A,C,D,AD"TYPE
PILOT ROD FOR"B"TYPE
"C" RING
IRON WASHER
IDLE GEAR
GEAR SEAT
CENTRAL GEAR
IDLE GEAR
GEAR SEAT
GEAR CASE
MAIN BEARING
Q'ty
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
2
2
3
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
4
1
1
1
NO
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
PARTS NO
GC30341-3
GP30351
GU30361
GP30371
GP30351
GD30381A
GD30381B
GD30381C
GD30381D
GD30383AD
GP20331
GP21291B
GF30401
GF30401B
GO30541-3
GO30544
GO30531
GE50411-4
GE50411-5
GE30413-7
GE30413-11
GY30421
GY30421B
GK20231B
GB30441-12A
GB30441-1A
GO20391
GO20391B
GJ30461
GJ3046B
GQ30471
GQ21361
GL30481-1
GM30491
GS30501
CD20111-1
CD20111-2
CH50671-3
CH20102-8
CH20514
P11020-1
E32203
W50109-2
W50104-2
P11020-4
GN30435
W10201-1
PARTS NAME-E
CAM
STEEL BALLS
STOP PILOT
STELL BALLS FOR A,C,D,AD
STEEL BALLS
SHAFT FOR "A" TYPE
SHAFT FOR "B" TYPE
SHAFT FOR "C" TYPE
SHAFT FOR "D" TYPE
SHAFT FOR "AD" TYPE
STEEL BALLS FOR "A,D,AD" TYPE(2mm)
STEEL BALLS FOR "B,C" TYPE(2.5mm)
WARING PLATE FOR "A,C,D,AD" TYPE
WARING PLATE FOR "B" TYPE
SPRING FOR "BSD-B6120L"
SPRING FOR "BSD-B6190L"
SPRING CAP
WARING SPRING FOR "B6120LA,C,D,AD" TYPE
WARING SPRING FOR "B6120LB" TYPE
WARING SPRING FOR "B6190LA,C,D,AD" TYPE
WARING SPRING FOR "B6190LB" TYPE
WARING SPRING BASE FOR "A,C,D,AD" TYPE
WARING SPRING BASE FOR "B" TYPE
"C"-RING FOR GY30421B (LB)
CLUTCH CASE-A,C,D,AD
CLUTCH CASE-B
BIT SPRING FOR "A,C,D,AD" TYPE
BIT SPRING FOR "B" TYPE
BIT SLEEVE FOR "A,C,D,AD" TYPE
BIT SLEEVE FOR "B" TYPE
"C" RING FOR "A,C,D,AD"
"C" RING FOR "B"
TORQUE ADJUST PIN
TORQUE ADJUST RING
"C" RING FOR GM30491
COUPLER
COUPLER (ESD)
GROUNDING MEANS
WASHER
SCREW
INSULATING WASHER FOR ESD ONLY(UP)
HEAT SINK
CLAMP
WASHER
INSULATING WASHER FOR ESD ONLY(DOWN)
MAIN BEARING
INSULATING WASHER
B6190L
Q'ty
1
2
1
2
2
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
2
2
1
1
2
1
1
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PARTS NO
AA50001-26N
AA50001-62N
CJ20011
CC50016
CC50016-1
CB50230-6
CB50230-7
CA50230-6
CA50230-7
CE50152-3
CE80001
CH30200
H10204
CC28028-2
EG31420
EG31414-4A
CH90154
CH20510
CH20102
MI90302
CH20102-24
MO50114
M20102-1
M11324
MG30081-1
GZ51901-3A
GZ51901-3B
GZ51901-3C
GZ51901-3D
GZ51901-3AD
MI31221
MI33241
GK20231
GI20251-1
G21302
GH20241-1
GG20271-1
GA91284
GN30321
GC30341-3
GP30351
PARTS NAME-E
CORD ASSEMBLY
CONNECTOR
SUSPENSION RING
TRIGGER ASSEMBLY
TRIGGER ASSEMBLY (ESD)
HOUSUNG-UNDERSIDE
HOUSUNG-UNDERSIDE-ESD
HOUSING-UPSIDE
HOUSING-UPSIDE-ESD
PUSH ROD
FIXTURE
SCREW
CHANGEOVER SWITCH
TRIGGER ASSEMBLY FOR B6120LF
PCB
P.C.B
SCREW FOR PCB
SCREW FOR ESD TYPE
SCREW FOR HOUSING
PILOT ROD
SCREW FOR MOTOR
MOTOR ASSEMBLY
GEAR COUPLER
GEAR
PILOT ROD
CLUTCH ASSEMBLY FOR "B6120LFA"
CLUTCH ASSEMBLY FOR "B6120LFB"
CLUTCH ASSEMBLY FOR "B6120LFC"
CLUTCH ASSEMBLY FOR "B6120LFD"
CLUTCH ASSEMBLY FOR "B6120LFAD"
PILOT ROD FOR"A,C,D,AD"TYPE
PILOT ROD FOR"B"TYPE
"C" RING
IRON WASHER
WASHER
IDLE GEAR
GEAR SEAT
GEAR CASE
MAIN BEARING
CAM
STEEL BALLS
Q'ty
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
2
2
3
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
2
NO PARTS NO
33 GU30361
34 GP30371
GP30351
35 GD30381A
GD30381B
GD30381C
GD30381D
GD30381AD
36 GP20331
GP21291B
37 GF30401
GF30401B
38 GO30541-3
39 GO30531
40 GE50411-4
GE50411-5
41 GY30421
GY30421B
42 GK20231B
43 GB30441-12A
GB30441-1A
44 GO20391
GO20391B
45 GJ30461
GJ3046B
46 GQ30471
GQ21361
47 GL30481-1
48 GM30491
49 GS30501
50 CD20111-1
CD20111-2
51 CH50671-3
52 CH20102-8
53 CH20514
54 P11020-1
55 E32203
56 W50109-2
57 W50104-2
58 P11020-4
59 GN30435
PARTS NAME-E
STOP PILOT
STELL BALLS FOR A,C,D,AD
STEEL BALLS
SHAFT FOR "A" TYPE
SHAFT FOR "B" TYPE
SHAFT FOR "C" TYPE
SHAFT FOR "D" TYPE
SHAFT FOR "AD" TYPE
STEEL BALLS FOR "A,D,AD" TYPE(2mm)
STEEL BALLS FOR "B,C" TYPE(2.5mm)
WARING PLATE FOR "A,C,D,AD" TYPE
WARING PLATE FOR "B" TYPE
SPRING
SPRING CAP
WARING SPRING FOR "A,C,D,AD" TYPE
WARING SPRING FOR "B" TYPE
WARING SPRING BASE FOR "A,C,D,AD" TYPE
WARING SPRING BASE FOR "B" TYPE
"C"-RING FOR GY30421B (LB)
CLUTCH CASE-A,C,D,AD
CLUTCH CASE-B
BIT SPRING FOR "A,C,D,AD" TYPE
BIT SPRING FOR "B" TYPE
BIT SLEEVE FOR "A,C,D,AD" TYPE
BIT SLEEVE FOR "B" TYPE
"C" RING FOR "A,C,D,AD"
"C" RING FOR "B"
TORQUE ADJUST PIN
TORQUE ADJUST RING
"C" RING FOR GM30491
COUPLER
COUPLER (ESD)
GROUNDING MEANS
WASHER
SCREW
INSULATING WASHER FOR ESD ONLY(UP)
HEAT SINK
CLAMP
WASHER
INSULATING WASHER FOR ESD ONLY(DOWN)
MAIN BEARING
B6120LF
Q'ty
1
2
2
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
2
2
1
1
2
1
B6120P
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PARTS NO
AA50001-26N
AA50001-62N
CJ20011
CB50231-6
CB50231-7
CA50231-6
CA50231-7
EG31421-1
CI50212-1
CI50212
CE50152-3
CE80001
CH30200
H10201
CH90151-1
EG31414-5A
CH90154
CH20510
CH20102
MI90302
CH20102-24
MO50113
M11322-1
MG91081
GZ51902-1A-J
GZ51902-1B-J
GZ51902-1C-J
GZ51902-1D-J
GZ51902-1AD-J
GZ51902-2A
GZ51902-2B
GZ51902-2C
GZ51902-2D
GZ51902-2AD
MI30241
GK20231
GI20251-1
GH20241
GG20271
G20101
GH20241
GG20271
GA91284
GN30321
GX33319-4
PARTS NAME-E
CORD ASSEMBLY
CONNECTOR
SUSPENSION RING
HOUSUNG-UNDERSIDE
HOUSUNG-UNDERSIDE (ESD)
HOUSING-UPSIDE
HOUSING-UPSIDE (ESD)
PCB
F/R SWITCHING ELEMENT-B6120P
F/R SWITCHING ELEMENT-B6190P
PUSH ROD FOR B6120P,B6190P
FIXTURE
SCREW FOR FIXTURE
SHUT OFF SWITCH
SCREW
PCB
SCREW
SCREW
SCREW
PILOT ROD
SCREW FOR MOTOR
MOTOR ASSEMBLY
GEAR
PILOT ROD
CLUTCH ASSEMBLY FOR-B6120PA
CLUTCH ASSEMBLY FOR-B6120PB
CLUTCH ASSEMBLY FOR-B6120PC
CLUTCH ASSEMBLY FOR-B6120PD
CLUTCH ASSEMBLY FOR-B6120PAD
CLUTCH ASSEMBLY FOR-B6190PA
CLUTCH ASSEMBLY FOR-B6190PB
CLUTCH ASSEMBLY FOR-B6190PC
CLUTCH ASSEMBLY FOR-B6190PD
CLUTCH ASSEMBLY FOR-B6190PAD
PILOT ROD
"C" RING
IRON WASHER
IDLE GEAR
GEAR SEAT
CENTRAL GEAR
IDLE GEAR
GEAR SEAT
GEAR CASE
MAIN BEARING
SHAFT GUIDE
Q'ty
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
2
2
3
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
4
1
1
1
1
NO
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
PARTS NO
GP30351
GF33317
GO30541
GO30544
GO30531
GV33316
GO33315-2
GO33315
GU30361
GE30411-18
GE30413-8
GP30371
GD33319A
GD33319B
GD33319C
GD33319D
GD33319AD
GP20331
GP21291B
GY33313
GB20381-8
GB20381-9
GO30452
GO20391B-J
GO20391B
GJ30461
GJ3046B
GQ30471
GQ21361
GL30481-1
GM30491
GS30501
CD20111-1
CD20111-2
CH50671-3
CH20102-8
CH20514
P11020-1
E32203
W50109-2
W50104-2
E30703
EG31420
P11020-4
GN30435
W10201-1
PARTS NAME-E
STEEL BALLS
WARING PLATE
SPRING FOR "B6120P"
SPRING FOR "B6190P"
SPRING CAP
INNER SPRING CAP
INNER SPRING-B6120P
INNER SPRING-B6190P
STOP PILOT
WRING SPRING FOR B6120P
WRING SPRING FOR B6190P
STELL BALLS
SHAFT FOR "A" TYPE
SHAFT FOR "B" TYPE
SHAFT FOR "C" TYPE
SHAFT FOR "D" TYPE
SHAFT FOR "AD" TYPE
BIT PILOT FOR "A&D&AD"
BIT PILOT FOR "B&C"
WRING SPRING BASE
CLUTCH CASE FOR "A.C.D.AD"TYPE
CLUTCH CASE FOR "B"TYPE
BIT SPRING FOR "B6120,6190PA,C,D,AD"
BIT SPRING-B6120PB
BIT SPRING-B6190PB
BIT SLEEVE FOR "A,C,D,AD"
BIT SLEEVE FOR "B"
"C" RING FOR GJ30461"A,C,D,AD"
"C" RING FOR GJ30461"B"
TORQUE ADJUST PING
TORQUE ADJUST RING
"C"RING
COUPLER
COUPLER (ESD)
GROUNDING MEANS
WASHER
SCREW
INSULATING WASHER FOR ESD ONLY(UP)
HEAT SINK
CLAMP
WASHER
DIODE
PCB
INSULATING WASHER FOR ESD ONLY(DOWN)
MAIN BEARING
INSULATING WASHER
B6190P
Q'ty
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
2
2
1
1
1
1
2
1
1
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PARTS NO
AA50001-26N
AA50001-62N
CJ20011
CB50231-6
CB50231-7
CA50231-6
CA50231-7
EG31421-1
CI50212-1
CE50152-3
CE80001
CH30200
H10201
CH90151-1
EG31414-5A
CH90154
CH20510
CH20102
MI90302
CH20102-24
MO50114
M20102-1
M11324
MG30081-1
GZ51902-3A-J
GZ51902-3B-J
GZ51902-3C-J
GZ51902-3D-J
GZ51902-3AD-J
MI30241
GK20231
GI20251-1
G21302
GH20241-1
GG20271-1
GA91284-1
GN30321
GX33319-4
GP30351
PARTS NAME-E
CORD ASSEMBLY
CONNECTOR
SUSPENSION RING
HOUSUNG-UNDERSIDE
HOUSUNG-UNDERSIDE (ESD)
HOUSING-UPSIDE
HOUSING-UPSIDE (ESD)
PCB
F/R SWITCHING ELEMENT
PUSH ROD
FIXTURE
SCREW FOR FIXTURE
SHUT OFF SWITCH
SCREW
PCB
SCREW
SCREW
SCREW
PILOT ROD
SCREW FOR MOTOR
MOTOR ASSEMBLY
GEAR COUPLER
GEAR
PILOT ROD
CLUTCH ASSEMBLY FOR-B6120PFA
CLUTCH ASSEMBLY FOR-B6120PFB
CLUTCH ASSEMBLY FOR-B6120PFC
CLUTCH ASSEMBLY FOR-B6120PFD
CLUTCH ASSEMBLY FOR-B6120PFAD
PILOT ROD
"C" RING
IRON WASHER
FAST GEAR GASKET
IDLE GEAR
GEAR SEAT
GEAR CASE
MAIN BEARING
SHAFT GUIDE
STEEL BALLS
Q'ty
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
2
1
3
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
2
NO
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
PARTS NO
GF33317
GO30541
GO30531
GV33316
GO33315-2
GU30361
GE30411-18
GP30371
GD33319A
GD33319B
GD33319C
GD33319D
GD33319AD
GP20331
GP21291B
GY33313
GB20381-8
GB20381-9
GO30452
GO20391B-J
GJ30461
GJ3046B
GQ30471
GQ21361
GL30481-1
GM30491
GS30501
CD20111-1
CD20111-2
CH50671-3
CH20102-8
CH20514
P11020-1
E32203
W50109-2
W50104-2
E30703
EG31420
P11020-4
GN30435
PARTS NAME-E
WARING PLATE
SPRING
SPRING CAP
INNER SPRING CAP
INNER SPRING
STOP PILOT
WRING SPRING
STELL BALLS
SHAFT FOR "A" TYPE
SHAFT FOR "B" TYPE
SHAFT FOR "C" TYPE
SHAFT FOR "D" TYPE
SHAFT FOR "AD" TYPE
BIT PILOT FOR "A&D&AD"
BIT PILOT FOR "B&C"
WRING SPRING BASE
CLUTCH CASE FOR "A.C.D.AD"TYPE
CLUTCH CASE FOR "B"TYPE
BIT SPRING FOR "A,C,D,AD"
BIT SPRING
BIT SLEEVE FOR "A,C,D,AD"
BIT SLEEVE FOR "B"
"C" RING FOR GJ30461"A,C,D,AD"
"C" RING FOR GJ30461"B"
TORQUE ADJUST PING
TORQUE ADJUST RING
"C"RING
COUPLER
COUPLER (ESD)
GROUNDING MEANS
WASHER
SCREW
INSULATING WASHER FOR ESD ONLY(UP)
HEAT SINK
CLAMP
WASHER
DIODE
PCB
INSULATING WASHER FOR ESD ONLY(DOWN)
MAIN BEARING
B6120PF
Q'ty
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
2
2
1
1
1
1
2
1
KILEWS ELECTRIC TOOLS（SHANGHAI）CO., LTD.
E-mail:service@kilews.com.cn
http://www.kilews.com.cn