ManualsLib - Makes it easy to find manuals online!

Coffee Machine
Service
Service
Service
Minuto
Service Manual
Rev. 02 March 2014
Table of contents
1.
Introduction
1.1.
1.2.
1.3.
1.4.
1.5
1.6.1.
1.6.2.
Documentation required
Tools and equipment required
Material
Safety warnings
Service Policy
External machine parts
Internal machine parts
2.
Technical specifications
2.1.
2.2.1
Technical specifications
Specification for the measurement of the coffee products
temperature
Specification for the measurement of the milk products
temperature
Machine parameters and performance
2.2.2.
2.3.
3.
User instructions
3.1.
3.2.
3.3.
3.4
3.5
3.6.
3.7
Customer menu in the Minuto Cappuccino
Customer menu in the Minuto Cappuccino for USA
Customer menu in the Minuto Class and Focus
Customer menu in the Minuto Class and Focus for USA
Customer menu in the Minuto Pure
Customer menu in the Minuto Pure for USA
Operation, cleaning and maintenance
4.
Operating logic
4.1.
Water circuit Minuto Cappuccino
Page
Table of contents
1
1
1
1
2
3
6
4.2.
4.3.
4.4.
4.5.
4.6.
4.7.
4.8.
4.9.
1
2
4.10.
4.11.
4.12.
4.13.
Page
Water circuit Minuto Class and Focus
Water circuit Minuto Pure
Milk carafe
Coffee cycle
Single microswitch
Temperature sensor
Coffee grinder
Low bean level detection, dose quantity adjustment,
coffee grinder blocked
Dose self-learning (SAS)
Water level detection (water tank)
Descaling request
Water filter
2
3
4
5
6
6
7
7
8
9
9
10
3
5
1
3
5
7
9
11
13
1
5.
Troubleshooting
5.1.1.
5.1.2.
5.2.1.
5.2.2.
5.3.1.
5.3.2.
5.4.1.
5.4.2.
5.5.1.
5.5.2.
5.6.1.
5.6.2.
5.7.
Minuto Cappuccino test mode
SteamOut
Minuto Cappuccino test mode for USA
SteamOut
Minuto Focus/Class test mode
SteamOut
Minuto Focus/Class test mode for USA
SteamOut
Minuto Pure test mode
Steam Out
Minuto Pure test mode for USA
Steam Out
Error messages
1
7
8
15
16
22
23
29
30
37
38
45
46
All parts of this document are the property of Saeco International Group.
All rights reserved. This document and all the information herein is provided without liability deriving from any errors or omissions. Furthermore, no part may be reproduced, used or
collected, except where express authorisation has been provided in writing or through a contractual agreement.
Published by Saeco International Group
Subject to modification
EN 4219 400 00020
2013-August-01
Downloaded from www.Manualslib.com manuals search engine
Table of contents
6.
Standard checks
6.1.
Repair schedule
Page
1
6.2.
Service schedule
1
6.3.
Final test
2
7.
Disassembly
7.1.
Outer Shell
1
7.2.
Coffee grinder
2
7.3.
Grinder blades
3
7.4.
Coffee grinder adjustment
4
7.5.1.
Two-way solenoid valve
5
7.5.2.
Carafe connection and hot water dispenser in
Minuto Cappuccino
5
7.6.
Pin boiler
5
7.7.
Gear motor
6
7.8.
Central plate
6
7.9.
Pump
7
7.10.
Flow-meter
7
7.11.
Boiler
7
7.12.
CPU board
8
7.13
Programming access for SSC (Saeco Service Center)
8
7.14.
KYB interface and display
8
7.15.
Fitting and removing Oetiker clamps
9
8.
Notes
9.
Water circuit diagram
10
Electrical diagram
MINUTO
Downloaded from www.Manualslib.com manuals search engine
CHAPTER 1
INTRODUCTION
MINUTO
Downloaded from www.Manualslib.com manuals search engine
MINUTO
1.1
01 INTRODUCTION
Documentation required
The following documentation is needed for repair procedures:
•
•
Instruction booklet for specific model
Technical documentation for specific model (diagrams, exploded view, sympton cure and
service manual)
1.2
Tools and equipment required
As well as the standard equipment, the following is required:
Qty.
1
1
1
1
1
Description
Screwdriver
Pliers for Oetiker clamps
CC -A - Vdc tester
Digital thermometer
SSC (Saeco Service Center)
1.3
Scale limit > 150°C
Programmer
(for programming and diagnostics mode)
Material
Description
Thermal paste
Descaler
Grease solvent
Silicone grease
1.4
Notes
Notes
Heating element > 200°C
Saeco descaler
Personal choice
Safe to use with food
Safety warnings
We recommend you consult the technical manual of the machine before performing any maintenance work.
Observe all applicable standards relating to the repair of electrical appliances.
Always disconnect the power plug from the mains before beginning repair work.
Simply turning off the main machine power switch is not an adequate safety precaution.
This domestic appliance is rated as insulation class I.
On completion of the repair work, insulation and dielectric rigidity tests must be performed.
Page 01 / 06
Downloaded from www.Manualslib.com manuals search engine
MINUTO
1.5
01 INTRODUCTION
Service POLICY grid as used for coffee machine
For IN WARRANTY repairs is mandatory to use the single components (not the assembly) available in the exploded views of the coffee machines or of the specific components. If you find the
information “SEE THE EXPLODED VIEW E........” in the assembly description field, it means that
the single components of the assembly are available in the other pages of the exploded view. It’s
possible to use the assembly only if there is a specific Symptom Cure that include this possibility
or when the single components are not available for the order.
List of principal assembly present in all our coffee machines
Components
COFFEE
GRINDER
BREWING
UNIT
BOILER
GEAR
MOTOR
FILTER
HOLDER
MILK
CARAFE
THERMAL
CARAFE
MILK ISLAND
Assembly use
Only for OOW repairs
Only for OOW repairs
Only for OOW repairs
Only for OOW repairs
Only for OOW repairs
Only for OOW repairs
Only for OOW repairs
Only for OOW repairs
Single components available
YES, to consult the specific exploded-view of
machine or of the Coffee Grinder on website
YES, to consult the specific exploded-view of
machine or of the Brewing unit on website
YES, to consult the specific exploded-view of
machine on website
YES, to consult the specific exploded-view of
machine on website
YES, to consult the specific exploded-view of
machine on website
YES, to consult the specific exploded-view of
machine on website
YES, to consult the specific exploded-view of
Thermal Carafe on website
YES, to consult the specific exploded-view of
Milk Island on website
the
the
the
the
the
the
the
the
Page 02 / 06
Downloaded from www.Manualslib.com manuals search engine
MINUTO
01 INTRODUCTION
1.6.1 External machine parts
Espresso/Coffee
selection level
Minuto Pure
Automatic Milk Frother
(also for steam dispensing)
(Class)
Classic Milk Frother (also
for water/steam dispensing)
(Focus)
Water tank Pre-ground coffee
compartment
Coffee bean
hopper with lid
Hot water
dispensing spout
Milk carafe
Service
door
Coffee
dispenser
Brew Unit
Dreg drawer
Power cable socket
and main switch
Drip tray+grille
CAPPUCCINO
ON/OFF button
Cappuccino brew
button
Coffee brew
button
Espresso brew
button
MENU
“Aroma”
Pre-ground coffee button
Special products button
Page 03 / 06
Downloaded from www.Manualslib.com manuals search engine
MINUTO
01 INTRODUCTION
CLASS
ON/OFF button
“Aroma”
Pre-ground coffee button
Coffee brew button
Hot water button
Espresso brew button
Steam button
MENU
FOCUS
ON/OFF button
“Aroma”
Pre-ground coffee button
Coffee brew button
Espresso brew button
Descaling button
Hot water button
Steam button
PURE
Espresso brew button
ON/OFF button
Coffee brew button
“Coffee grounds drawer” light
“No water” light
“Warning” light
“No coffee” light
“Start descaling” light
“Descaling” light
Descaling button
Espresso/Coffee
selection level
CAPPUCCINO for USA
ON/OFF button
Long Coffee
brew button
Medium Coffee
brew button
Espresso brew
button
MENU
“Aroma”
Pre-ground coffee button
Cappuccino brew button
Page 04 / 06
Downloaded from www.Manualslib.com manuals search engine
MINUTO
01 INTRODUCTION
Automatic Milk Frother
(also for steam dispensing)
(Class)
CLASS
for USA
ON/OFF button
Steam wand + rubber grip for
Automatic Milk Frother
(also for hot water dispensing)
Espresso/Coffee
selection level
Long coffee
brew button
Medium coffee
brew button
Espresso
brew button
Menu button
“Aroma”
Pre-ground coffee button
Hot water/steam
button
FOCUS
for USA
ON/OFF button
Classic Milk Frother (also
for water/steam dispensing)
(Focus)
Long coffee
brew button
Medium coffee
brew button
Espresso
brew button
Descaling button
“Aroma”
Pre-ground coffee button
Hot water/steam
button
PURE
for USA
Espresso brew button
ON/OFF button
Coffe brew button
“No water” light
Empty coffee grounds
drawer” light
Steam button
“No coffee” light
Hot water button
Descaling cycle light
General warning light
Descaling button
Rinse cycle light
Page
Downloaded from www.Manualslib.com manuals search engine
05 / 06
MINUTO
01 INTRODUCTION
1.6.2 Internal machine parts
Power board
Pump
Thermostat
Flow-meter
Boiler
Grinding
adjustment insert
Coffee grinder
Safety valve
Steam pipe
2-way
solenoid valve
Coffee
dispenser
Boiler pin
Page 06 / 06
Downloaded from www.Manualslib.com manuals search engine
CHAPTER 2
TECHNICAL
SPECIFICATIONS
MINUTO
Downloaded from www.Manualslib.com manuals search engine
MINUTO
2.1.
02 TECHNICAL SPECIFICATIONS
Technical specifications
Power supply and output:
Temperature monitoring:
Safety system:
Coffee heat exchanger output:
Stainless steel
Gear motor:
Pump:
Overpressure valve:
Water filter:
Coffee grinder:
Automatic dosage:
Power consumption:
Dimensions: W x H x D in mm:
Weight:
Water tank capacity:
Coffee bean hopper capacity:
Dreg drawer capacity:
Water circuit filling time:
Heating time:
Grinding time:
240 V~ 50 Hz 1850 W - 230 V~ 50/60 Hz 1850 W
120 V~ 60 Hz 1500 W
(NTC) variable resistor sensor - transmits the value to the
electronic card
2 thermostats at 190°C one shot
(230 V~) 1900 W - (120 V~) 1300 W - (100 V~) 1100 W
for coffee, hot water and steam dispensing
2 rotation directions; power supply 24VC
Ulka Type EP5/S GW approx. 13-15 bar with reciprocating
piston and thermal switch 100°C 48 W, 230V, 50 Hz, 120V,
60Hz 100V, 50/60 Hz
Opening at approx. 16-18 bar
In tank
Direct current motor with flat ceramic grinder blades
Dose adjustment controlled by the electronic system
During heating phase- approx. 5.6 A
215 x 330 x 429 mm / 8.5”x13”x16.9”
6.7 kg / 14.77 lbs
1.5 l
250 g. / 1 cup
15
Approx. 15 sec Max. on first filling cycle
Approx. 45 sec.
Approx. 8-10 sec.
Page 01 / 05
Downloaded from www.Manualslib.com manuals search engine
MINUTO
02 TECHNICAL SPECIFICATIONS
2.2.1. Specification for the measurement of the coffee products temperature.
The temperature is influenced by the flow from the dispenser and stratification of temperatures in
the glass. In order to consider these phenomena and to introduce measures that allow comparisons in controlled conditions, below guidelines must be followed:
Conditions:
a) Water temperature in tank: 23°C (+/-2°C).
b) It must be used a plastic cup (see picture N°1).
c) It must be used a thermocouple thermometer (e.g. type K - see picture N°2).
d) The coffee machine is tested without any change of parameters or calibrations, which may
affect the temperature of products, so the measurement of temperature must be done with
machine in default factory setting.
Procedure:
1. The temperature must be measured in the cup, immediately after dispensing. Cup has to be
placed on a non-metal surface using a thermocouple thermometer.
2. The temperature in the cup is measured by immersing the probe of the thermometer up to
touch the bottom.The probe then must be moved in a circular motion for 5/6 rotations. At the
of the rotations, stop in the center of the cup.
3. The highest temperature measured during the rotations is the value we are searching for, and
that must be reported;
4. Test measurement: from end of dispensing to the end of rotations must be completed within 12
seconds.
Limits of acceptability
The acceptance limits are divided by features and products and are the following:
Espresso Coffee Italy Q.ty 25/40 gr.
Temperature of 1st product 69°C ≤ 85°C
Temperature of 2nd product 72°C ≤ 85°C
Coffee Q.ty 70/120 gr.
Temperature of 1st product 69°C ≤ 85°C
Temperature of 2nd product 72°C ≤ 85°C
Picture 1
Picture 2
Page
Downloaded from www.Manualslib.com manuals search engine
02/ 05
MINUTO
02 TECHNICAL SPECIFICATIONS
2.2.2. Specification for the measurement of the Milk products temperature.
Milk evaluation
To carry out the test, a partially skimmed UHT milk with a percentage of grease between 1.51.8% at a refrigerator temperature Trefr. (between 4 to 10°C) must be used.
The milk product must be checked on a beaker of 250 ml of capability and with an inner diameter
of 70mm, brewing 100gr of product.
Parameters to be respected:
The parameters to be respected are: milk temperature and height of the cream. Each of these
parameters, however, must be evaluated depending on the type of system used for the production
of hot milk.
Actually three types of devices are present on the appliances:
-
Manual system (pannarello)
Semi-Automatic system (cappuccinatore)
Automatic system (carafe, Pinless wonder system, etc.)
Milk temperature in the beaker:
System without Pinless Wonder: e.g. Xelsis, Exprelia, Syntia, Intelia.
With milk at Trefr. (about 4-10 °C):
≥ 36
System with Pinless Wonder: New royal, Energica Pure, Intelia EVO Latte.
With milk at Trefr. (about 4-10 °C):
≥ 45
Height of the milk cream in the beaker:
Manual system (pannarello)
≥ 15mm on 100gr. of brewed product
Semi-automatic system (cappuccinatore)
≥ 20mm on 100gr. of brewed product
Automatic system: carafe, cappuccinatore, Pinless wonder (New Royal, Energica Pure, Intelia EVO
latte)
≥ 20mm on 100gr. of brewed product
How to measure the temperature of the milk.
1)
The measurement is carried out in the beaker, immediately after the end of milk brew,
positioned on a non-metallic surface, using a thermocouple thermometer (eg. Type K).
Stop the preparation of mixed product: at the end of milk brewing, where
“One Touch product” function is present.
2)
The temperature is measured by immersing the probe of the thermometer, positioning the
probe inside the beaker at about 10mm from the bottom of the container, then the probe
moves in a circular motion for 3-5 turns, stopping at the end, at the center of the beaker.
It detects the maximum temperature reached in a time of relief between 3 to 5 seconds. It
is important the mixing of milk before the measurement at 10mm from the bottom of the
beaker. If the mixing is correct, temperature, for a few fractions of a second, during the
measurement should not oscillate.
Page 03 / 05
Downloaded from www.Manualslib.com manuals search engine
MINUTO
02 TECHNICAL SPECIFICATIONS
How to measure the milk cream.
The temperature (Trefr or Tamb) of the milk doesn’t affect as much the test result on measuring
the milk cream; by convection is assumed to always use milk at refrigerator temperature Trefr..
Manual systems (Pannarello)
Pour 100cc. of milk at Trefr. in a beaker of 250 ml of capacity and with a inner diameter of 70 mm;
with machine in steam mode:
1.
2.
3.
Open the steam knob to discharger water circuit for 4 sec, then close the knob.
Place the beaker with the frother dipped in milk, open the steam knob to maximum and
start the chronometer.
After about 30 to 60 seconds, close the knob and check the result on milk.
Semi-automatic systems (cappuccino)
Pours milk at Trefr. in a container ; with the machine in steam mode:
1.
2.
3.
Open the steam knob to discharge water circuit for 4 sec. then close the knob.
Insert the silicone tube in the milk container, placing a beaker of 250 ml capacity and with
an inner diameter of 70 mm under the cappuccino maker and open the steam knob.
After having provided 100gr. of product, close the knob and check the result obtained on
milk. Note: The same applies to machines which have a steam key on the user interface
and a solenoid valve in place of the steam tap.
Automatic: Carafe, Cappuccino Pinless wonder (New Royal, Energica Pure, Intelia EVO
Latte), etc..
After setting the machine to delivery of 100gr. of product:
1.
2.
Launch the “hot milk” function.
Collect the product in a beaker with a 250ml of capacity and with an inner diameter of
70 mm, and verify the result obtained on milk. Carry out the test using milk at a Trefr..
In case the machine allows modify of the emulsion through the menu, use the machine with the
emulsion set to the default value.
Related to the above testing procedure derives the following table of acceptability:
Manual, Semi-Automatic and Automatic’s Milk System
Grams of Product
Minimun Height of the milk cream
≥ 130
120
110
100
90
80
70
≥
≥
≥
≥
≥
≥
30mm
25mm
22mm
20mm
16mm
13mm
≥ 11mm
NB: To verify more accurately the height of the cream, a practical expedient dictated by experience is to add to the product just delivered a small amount of coffee. The addition of coffee
immediately put in evidence the surface of separation between liquid and cream.
Page 04 / 05
Downloaded from www.Manualslib.com manuals search engine
MINUTO
2.3.
02 TECHNICAL SPECIFICATIONS
Machine parameters and performance
PRODUCT
QUANTITY
Espresso
Long coffee
Hot water
Steam
pannarello
(frother)
Minimum
Default
Maximum
Programm. by
User
quantity
quantity
quantity
Production /
programmable
(Puls.)
(Puls.)
(Puls.)
Service
50
165
600
Yes
No
70
440
600
Yes
No
Continues until the water supply has been exhausted (capacitive sensor)
Continues until the water supply has been exhausted (capacitive sensor)
Descaling cycle frequency
HardWater hardness
Without water filter
With water filter
ness
1
Soft (up to 7°dH)
240 litres (480,000 pulses)
480 litres (960,000 pulses)
2
Medium (7° - 14°dH)
120 litres (240,000 pulses)
240 litres (480,000 pulses)
3
Hard (15° - 21°dH)
60 litres (120,000 pulses)
120 litres (240,000 pulses)
4
Very hard (over 21°dH)
30 litres (60,000 pulses)
60 litres (120,000 pulses)
The default water hardness level is 4. Each litre of water corresponds to approximately
2,000 pulses.
In the machines where is not possible change the water hardness the default
hardness level is 3.
DREG DRAWER
Description and values
5 sec.
Time-out for dreg drawer
Reset dreg counter
Dreg emptying alarm, if the dreg drawer is
removed for more than 5 seconds.
STANDBY
Inlet time (default)
Inlet time programmed by Production/Service
Boiler temperature during Standby
WATER TANK
Water reserve (pulses) with water filter
Water reserve (pulses) with no water filter
Water reserve modifiable by Production/Service
departments
"Fill tank" alarm
"No tray" alarm
Water mains
Description and values
30 minutes
Yes
Boiler OFF
Description
200
200
No
Yes
Yes (Fill tank)
No
Page
Downloaded from www.Manualslib.com manuals search engine
05 / 05
CHAPTER 3
USER INSTRUCTIONS
MINUTO
Downloaded from www.Manualslib.com manuals search engine
MINUTO
3.1.
03 USER INSTRUCTIONS
Customer menu in the Minuto Cappuccino
ON/OFF button
Cappuccino brew
button
Coffee brew
button
Espresso brew
button
MENU
“Aroma”
Pre-ground coffee button
Special products button
This machine is equipped with a colour-coded system to make your understanding of the display
signals easier.
The icons are colour-coded according to the traffic light principle.
Machine ready signals (GREEN colour)
The machine is ready to brew
products.
Milk froth brewing.
The machine is ready to brew
pre-ground coffee.
The machine is frothing the
milk for the cappuccino.
The machine is brewing one
cup of espresso.
The machine is brewing the
coffee for the cappuccino
The machine is brewing one
cup of coffee.
The machine is programming the
amount of milk to dispense for
cappuccino.
The machine is brewing two
cups of espresso.
The machine is programming the
amount of coffee to be brewed
for cappuccino.
The machine is brewing two
cups of Coffee.
The machine is programming the
amount of milk to dispense for
milk froth.
The machine is programming the
amount of coffee to be brewed.
Insert the water dispensing
spout and press the “ ” button
to start dispensing.Press “ ” to
exit.
Coffee brewing using pre-ground
coffee in progress.
Milk froth or hot water selection.
Hot water dispensing.
The machine will remind the user
that the carafe must be inserted.
The machine will remind the user
that the carafe must be inserted
when programming a product
containing milk.
Page
Downloaded from www.Manualslib.com manuals search engine
01/ 13
MINUTO
03 USER INSTRUCTIONS
Machine ready signals (YELLOW colour)
The machine is heating up to
brew beverages or dispense
hot water/steam.
The brew group is being reset
due to machine reset.
The machine is performing
the rinse cycle. Wait until the
machine has completed the
cycle.
Refill the coffee bean hopper
with coffee beans and restart
the cycle.
The machine needs the
“INTENZA+” water filter to be
replaced.
The machine automatically
primes the water circuit.
The machine needs to be descaled. Press the “
” button to start the descaling
process. Follow the steps described in the “Descaling” chapter of this manual.
If you want to descale later, press the “
” button to continue using the machine.
Please note that not descaling your machine will ultimately make it stop
working properly. In this case repair is NOT covered under your warranty.
Machine ready signals (RED colour)
Completely insert the drip
tray with the coffee grounds
drawer into the machine
and close the service door.
Empty the coffee grounds
drawer. Wait about 5 seconds
before reinserting it.
Exx
Fill the coffee bean hopper and
refit the lid.
The brew group must be inserted
into the machine.
Fill the water tank.
Turn off the machine. After 30 seconds, turn it on again. Try this 2 or 3 times.
If the machine does not start, contact the Philips SAECO hotline in your country
and quote the error code shown on the display. The contact details can be found in
the warranty booklet packed separately or on www.philips.com/support.
Page 02 / 13
Downloaded from www.Manualslib.com manuals search engine
MINUTO
3.2.
03 USER INSTRUCTIONS
Customer menu in the Minuto Cappuccino for USA
ON/OFF button
Long Coffee
brew button
Medium Coffee
brew button
Espresso brew
button
MENU
“Aroma”
Pre-ground coffee button
Cappuccino brew button
This machine is equipped with a colour-coded system to make your understanding of the display
signals easier.
The icons are colour-coded according to the traffic light principle.
Machine ready signals (GREEN colour)
Select the programming menu
The machine is ready to brew
or special beverages menu.
products.
The machine is ready to brew
pre-ground coffee.
Froth milk or hot water selection.
The machine is brewing one
cup of espresso.
Hot water dispensing.
The machine is brewing two
cups of espresso.
Milk froth brewing.
The machine is programming the
amount of espresso to be brewed.
The machine is frothing the
milk for the cappuccino.
Coffee brewing using pre-ground
coffee in progress.
The machine is brewing one cup
of medium coffee.
The machine is programming the
amount of medium coffee to be
brewed.
The machine brewing one cup of
long coffee.
The machine is brewing the
coffee for the cappuccino
The machine is programming the
amount of milk to dispense for
cappuccino.
The machine is programming the
amount of coffee to be brewed
for cappuccino.
The machine is programming the
amount of milk to dispense for
froth milk.
The machine is programming
the amount of long coffee to be
brewed.
Page 03 / 13
Downloaded from www.Manualslib.com manuals search engine
MINUTO
Insert the water dispensing spout
and press the “ ” button to start
dispensing. Press “ ” to exit.
The machine will remind the user
that the carafe must be inserted.
03 USER INSTRUCTIONS
The machine will remind the user
that the carafe must be inserted
when programming a product
containing milk.
Machine ready signals (YELLOW colour)
The machine is in warm-up
phase to brew beverages or
dispense hot water/steam.
The brew group is being reset
due to machine reset.
The machine is performing
the rinse cycle. Wait until the
machine has completed the cycle.
Fill the coffee bean hopper with
coffee beans, refit the lid and
restart the cycle.
The machine needs the
The machine automatically
“INTENZA+” water filter to be
primes the water circuit.
replaced.
The machine needs to be descaled. Press the “
” button to start the descaling
process. Follow the steps described in the “Descaling” chapter of this manual.
If you want to descale later, press the “
” button to continue using the machine.
Please note that not descaling your machine will ultimately make it stop
working properly. In this case repair is NOT covered under your warranty.
Machine ready signals (RED colour)
Completely insert the drip
tray with the coffee grounds
drawer into the machine
and close the service door.
Empty the coffee grounds
drawer. Wait about 5 seconds
before placing it back.
Fill the coffee bean hopper.
The brew group must be inserted
into the machine.
Fill the water tank.
Set the “ESPRESSO” or “COFFEE” selection lever to “ESPRESSO” within 30
seconds to complete brewing.
Set the “ESPRESSO” or “COFFEE” selection lever to “COFFEE” within 30 seconds
to complete brewing.
Exx
A beverage has been selected without the coff ee bean hopper inner lid on
the machine. Place the coff ee bean hopper inner lid on the machine within
30 seconds to complete brewing.
Turn off the machine. After 30 seconds, turn it on again. Try this 2 or 3 times.
If the machine does not start, contact the Philips SAECO hotline in your country
and communicate the Error-code which you see on the display. You can find its
contact details in the warranty booklet packed separately or on
www.philips.com/support.
Page 04 / 13
Downloaded from www.Manualslib.com manuals search engine
MINUTO
3.3.
03 USER INSTRUCTIONS
Customer menu in the Minuto Class and Focus
FOCUS
ON/OFF button
“Aroma”
Pre-ground coffee button
Coffee brew button
MENU
Hot water button
Descaling button
Hot water button
Steam button
This machine is equipped with a colour-coded system to make your understanding of the display
signals easier.
The icons are colour-coded according to the traffi c light principle.
Espresso brew button
Steam button
Machine ready signals (GREEN colour)
The machine is ready to brew
products.
The machine is brewing one cup
of Coffee.
The machine is ready to brew
pre-ground coffee.
The machine is brewing two cups
of espresso.
Hot water dispensing.
The machine is brewing two cups
of Coffee.
Steam dispensing.
The machine is programming the
amount of coffee to be brewed.
The machine is brewing one cup
of espresso
Coffee brewing using pre-ground
coffee in progress.
Machine ready signals (YELLOW colour)
The machine is heating-up to
brew beverages or dispense hot
water.
The
machine
needs
the
“INTENZA+” water filter to be
replaced.
The machine performs the rinsing
cycle. Wait until the machine has
completed the cycle.
The brew group is being reset
due to machine reset.
Page 05 / 13
Downloaded from www.Manualslib.com manuals search engine
MINUTO
03 USER INSTRUCTIONS
Refill the coffee bean hopper with
coffee beans and restart the cycle.
Prime the circuit.
The machine needs to be descaled. Press the “
” button to enter the
descaling menu.
If you want to descale later, press the “
” button to continue using the
machine.
Please note that not descaling your machine will ultimately make it stop working
properly. In this case repair is NOT covered under your warranty
Machine ready signals (RED colour)
Insert the drip tray with the coffee
grounds drawer into the machine
and close the service door.
Fill the coffee bean hopper.
Exx
The brew group must be inserted
into the machine.
Empty the coffee grounds drawer.
Fill the water tank.
Turn off the machine. After 30 seconds, turn it on again. Try this 2 or 3 times.
If the machine does not start, contact the Philips SAECO hotline in your
country and communicate the the Error-code which you see on the display.
You can find its contact details in the warranty booklet by-packed separately
or on www.philips.com/support.
Page 06 / 13
Downloaded from www.Manualslib.com manuals search engine
MINUTO
3.4.
03 USER INSTRUCTIONS
Customer menu in the Minuto Class and Focus for USA
CLASS
for USA
FOCUS
for USA
ON/OFF button
Long coffee
brew button
Medium coffee
brew button
Menu button
“Aroma” Pre-ground coffee
button
Espresso
brew button
Hot water/steam
button
Descaling button
“Aroma” Pre-ground coffee
button
Hot water/steam
button
This machine is equipped with a colour-coded system to make your understanding of the display
signals easier.
The icons are colour-coded according to the traffi c light principle.
Machine ready signals (GREEN colour)
The machine is ready to brew
products.
The machine is programming the
amount of coffee to be brewed.
The machine is ready to brew
pre-ground coffee.
Espresso brewing using
pre-ground coffee in progress.
Steam or hot water selection.
The machine is brewing one cup
of medium coffee.
Hot water dispensing.
The machine is programming the
amount of medium coffee to be
brewed.
Steam dispensing.
The machine is brewing one cup
of long coffee.
The machine is brewing one cup
of espresso
The machine is programming
the amount of long coffee to be
brewed.
The machine is brewing two
cups of espresso.
Page
Downloaded from www.Manualslib.com manuals search engine
07/ 13
MINUTO
03 USER INSTRUCTIONS
Machine ready signals (YELLOW colour)
Class
The machine is in warm-up phase to brew beverages or dispense hot water/steam.
Focus
The machine is heating-up to brew beverages or dispense hot water.
The machine is performing the
rinse phase. Wait until the machine
has completed the cycle.
The machine needs the
“INTENZA+” water filter to be
replaced.
Refill the coffee bean hopper
with coffee beans.
Put back the coffee bean
hopper lid and restart the cycle.
Prime the circuit.
The brew group is being reset
due to machine reset.
The machine needs to be descaled. Press the “
” button to enter the
descaling menu.
If you want to descale later, press the “
” button to continue using the
machine.
Please note that not descaling your machine will ultimately make it stop working
properly. In this case repair is NOT covered under your warranty
Machine ready signals (RED colour)
Completely insert the drip tray
with the coff ee grounds drawer
into the machine and close the
service door.
Fill the coffee bean hopper.
The brew group must be inserted
into the machine.
Empty the coff ee grounds
drawer. Wait about 5 seconds
before placing it back.
Fill the water tank.
Set the “ESPRESSO” or “COFFEE” selection lever to “ESPRESSO” within 30
seconds to complete brewing.
Set the “ESPRESSO” or “COFFEE” selection lever to “COFFEE” within 30 seconds
to complete brewing.
A beverage has been selected without the coffee bean hopper inner lid on the
machine. Place the coffee bean hopper lid on the machine within 30 seconds to
complete brewing.
Exx
Turn off the machine. After 30 seconds, turn it on again. Try this 2 or 3 times.
If the machine does not start, contact the Philips SAECO hotline in your country and
communicate the the Error-code which you see on the display.
You can find its contact details in the warranty booklet by-packed separately
or on www.philips.com/support.
Page 08 / 13
Downloaded from www.Manualslib.com manuals search engine
MINUTO
03 USER INSTRUCTIONS
3.5.
Customer menu in the Minuto Pure
ON/OFF button
Espresso brew button
Coffee brew button
“Coffee grounds drawer” light
“No water” light
“Warning” light
“No coffee” light
“Start descaling” light
“Descaling” light
Descaling button
Warning signals
Flashing
The machine is busy and is performing one of the following operations:
- Warm-up
- Automatic rinse.
The machine automatically manages phases in order to complete the
operations.
The machine is
priming the circuit.
The machine is brewing
two cups of coffee.
Quick double flashing
Flashing
The machine is
programming the amount
of espresso to brew.
The machine is ready
to brew products.
Quick flashing
Steady on
The machine is
programming the amount
of coffee to be brewed.
The machine is brewing
one cup of espresso.
Quick flashing
Slow flashing
The machine is brewing
one cup of coffee.
Fill the water tank.
Steady on
Slow flashing
Completely insert the
drip tray with the coffee
grounds drawer into the
machine and close the
service door.
The machine is brewing
two cups of espresso.
Quick double flashing
Steady on
Page 09 / 13
Downloaded from www.Manualslib.com manuals search engine
MINUTO
03 USER INSTRUCTIONS
The brew group is
being reset due to
machine reset.
Fit the Brew Group.
Slow flashing
Quick flashing
Empty the coffee
grounds drawer.
Steady on
While emptying the coff ee grounds drawer.
Note:
The coffee grounds drawer should only be inserted after
completion of the reset that takes place when the
Flashing
off and the
light turns
light becomes steady on.
Refi ll the coff ee bean
hopper with coff ee beans
and restart the cycle.
Steady on
Steady on
The machine needs to be descaled. Follow the steps described in the
“Descaling” chapter of this manual.
Please note that not descaling your machine will ultimately
make it stop working properly. In this case repair is NOT
covered under your warranty.
Turn off the machine. After 30 seconds, turn it on again.
Repeat the procedure 2 or 3 times.
If the machine does not start, contact the Philips SAECO hotline in
your country.
All lights flashing simultaneously
Page 10 / 13
Downloaded from www.Manualslib.com manuals search engine
MINUTO
3.6.
03 USER INSTRUCTIONS
Customer menu in the Minuto Pure for USA
Espresso brew button
ON/OFF button
Coffee brew button
“No water” light
Empty coffee grounds
drawer” light
Steam button
“No coffee” light
Hot water button
General warning light
Descaling cycle light
Descaling button
Rinse cycle light
The machine is performing one of the following operations:
- Warm-up
- Automatic rinse.
Flashing
You have to prime the machine by pressing the espresso
button. Once pressed, the “ ” button turns off.
During priming the “ ” and “ ” keep on fl ashing.
They stop fl ashing when the priming is fi nished.
“
” Steandy on and “
” and “
”Flashing
The machine is
ready for use.
Steady on
The machine is brewing
two cups of coffee.
Quickly double flashing
The machine is
programming the amount
of espresso to brew.
The machine is brewing
one cup of coffee.
Flashing Quickly
Flashing slowly
The machine is
programming the amount
of coffee to be brewed.
The machine is brewing
one cup of espresso.
Flashing slowly
Flashing Quickly
The machine is brewing
two cups of espresso.
Quickly double flashing
The machine is dispensing
steam.
Flashing slowly
Page 11 / 13
Downloaded from www.Manualslib.com manuals search engine
MINUTO
03 USER INSTRUCTIONS
The machine is in the
stop steam dispensing
phase
Flashing Quickly
The machine is dispensing
hot water.
Flashing slowly
Fill the water tank.
Steady on
Steady on
Completely insert the
drip tray with the coffee
grounds drawer into the
machine and close the
service door.
Insert the brew group
properly.
The brew group is being
reset due to machine
reset.
Flashing slowly
Flashing Quickly
Empty the coffee
grounds drawer.
Steady on
The coff ee grounds drawer is not inserted into the machine.
Wait a few seconds till the “ ” goes out and the “ ” is steady on. Then
insert the coffee grounds drawer in the machine and close the service
door.
Flashing
Steady on
Refill the coffee bean hopper with coffee beans and try again to make a
coff ee. The light turns off only when the bean hopper lid has been placed
back.
It is possible to dispense steam and hot water when this warning light
shows.
The bean hopper lid has been removed after having selected
a coffee product. Put the lid back on.
Flashing slowly
The machine needs to be descaled. Follow the steps described in the
“Descaling” chapter of this manual.
Please note that not descaling your machine will ultimately make it stop
working properly. In this case repair is NOT covered under your warranty.
Steady on
Turn off the machine. Turn it back on after 30 seconds.
Repeat the procedure 2 or 3 times.
If the machine does not start, contact the Philips SAECO hotline in your
country (contact details in the warranty booklet)
All lights flashing simultaneously
Page
Downloaded from www.Manualslib.com manuals search engine
12 / 13
MINUTO
03 USER INSTRUCTIONS
3.7.
Operation, cleaning and maintenance
Operating the machine
1
Fill water tank
2
Fill the coffee bean hopper
3
Switch on the appliance
4
Press the button to start the
appliance
5
Heating
When the heating phase begins, wait for it to finish
6
Rinse
Carry out a rinse cycle for the internal circuits
7
Machine ready
The machine is ready to dispense beverages
CLEANING AND TECHNICAL SERVICING
A
Empty the dregs drawer
When indicated
B
Empty the drip tray
As necessary
C
Clean the water tank
Weekly
D
Clean the coffee bean hopper
As necessary
E
Clean the casing
As necessary
Clean the brewing unit
Every time the coffee bean hopper is filled or weekly
Lubricate the brewing unit
After 500 dispensing cycles or when the grease is no
longer present on the brewing unit
F
H
Clean the unit housing
Weekly
Descaling
When indicated
Descaling cycle frequency
Hardness
Water hardness
Without water filter
With water filter
1
Soft (up to 7°dH)
240 litres (480,000 pulses)
480 litres (960,000 pulses)
2
Medium (7° - 14°dH)
120 litres (240,000 pulses)
240 litres (480,000 pulses)
3
Hard (15° - 21°dH)
60 litres (120,000 pulses)
120 litres (240,000 pulses)
4
Very hard
(over 21°dH)
30 litres (60,000 pulses)
60 litres (120,000 pulses)
Page 13 / 13
Downloaded from www.Manualslib.com manuals search engine
CHAPTER 4
OPERATING LOGIC
MINUTO
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Safety valve
Pump
Water tank
Water discharge
Brewing Unit
Carafe
connection
Two - Way
solenoid valve
Water discharge
Boiler
Two - Way
solenoid
valve
4.1.
Hot water
Water
Flowmeter
MINUTO
04 OPERATING LOGIC
Water circuit Minuto Cappuccino
Page 01 / 10
Downloaded from www.Manualslib.com manuals search engine
Safety valve
Safety
valve
Pump
Pump
Steam pipe
pipe
Steam
Water
Water
discharge
discharge
Brewing Unit
Brewing
Unit
Flowmeter
Flowmeter
Boiler
Boiler
Two-way solenoid
solenoid valve
Two-way
valve
4.2.
Water tank
Water
tank
Hot water /steam
Water
MINUTO
04 OPERATING LOGIC
Water circuit Minuto Class and Focus
Page 02 / 10
MINUTO
04 OPERATING LOGIC
Water circuit Minuto Pure
Safety valve
Water discharge
Water tank
Pump
Hot water
Water
Flowmeter
Brewing Unit
Boiler
4.3.
Page
Downloaded from www.Manualslib.com manuals search engine
03 / 10
MINUTO
04 OPERATING LOGIC
4.4. Milk Carafe
1
2
3
Steam
1)Steam input
2)Bring the cappuccino maker into dispensing
position
3)Milk tank
The milk is heated by the
steam and taken towards
the emulsion chamber
where it is mixed with
air and transformed into
foam
The steam passes
through the pipe creating
a sucking effect that pulls
the milk upwards
Page
Downloaded from www.Manualslib.com manuals search engine
04/ 10
MINUTO
4.5.
04 OPERATING LOGIC
Coffee cycle
Main switch ON
START
STOP
Time
Coffee grinder
Pulses
(Dosage)
Heating
approx.
45 sec.
Pump
*
Brewing unit gear
motor
Status
Heating
Ready
Pump operation (flow
meter pulses) in
accordance with the
amount of product
selected.
Coffee cycle
Notes: * Only with Pre-brewing
Status
Microswitch
OFF
ON
Single microswitch gear motor
Switching on
When the machine is switched on, the gear motor repositions itself as follows:
- It acts on microswitch 1 (see following chapter).
- The gear motor changes its rotation direction and moves upwards again by approx. 1-2 mm.
- The boiler begins to heat the water for approx. 45 sec., at full power, in order to reach the
optimal temperature. The temperature will then remain at a constant level.
Coffee cycle
The coffee grinder starts the grinding process (controlled by pulses generated by a sensor).
The gear motor (brewing unit) moves to the brewing position.
Preliminary dispensing phase (short pump activity, short pause).
Product dispensing (the pump operation period is defined by the amount of product dispensed).
5. The gear motor moves to its home position (the dregs are expelled automatically).
1.
2.
3.
4.
Page 05 / 10
Downloaded from www.Manualslib.com manuals search engine
MINUTO
4.6.
04 OPERATING LOGIC
Single microswitch
The gear motor is powered by a direct current motor that engages with the smaller
double toothed wheel using a worm screw.
The unit is mounted on the axle of the large
gear wheel and when a coffee is requested, it
moves from the standby position to the dispensing position, and then back to the standby position again.
2
- Standby position: 1
- Dispensing position: 2
1
4.7.
Temperature sensor (adjustment)
Temp. (°C) R nom (kΩ)
20
61.465
50
17.599
75
7.214
80
6.121
85
5.213
90
4.459
100
3.3
125
1.653
150
0.893
ΔR (+/- %)
8.6
5.9
4.1
3.7
3.4
3.1
2.5
3.9
5.1
An NTC is used as a temperature sensor; in the event of overheating this reduces boiler element
power consumption.
The electronic system detects the current boiler temperature from the drop in voltage of the
sensor and adjusts it accordingly.
Heating element values and corresponding temperatures: see table.
Page 06 / 10
Downloaded from www.Manualslib.com manuals search engine
MINUTO
04 OPERATING LOGIC
4.8.
Coffee grinder
5
6
4
1
2
3
The coffee grinder is driven by a direct current motor (1) using a worm screw helicoidal wheel
transmission (2).
The worm screw (2) drives a plastic gear wheel (3), which turns the lower grinder (4) and the
increment pin (5)
There are two magnets (6) in the gear wheel; at every rotation these induce two pulses to a Hall
sensor, which in turn transmits them to the electronic system.
4.9.
V
Low bean level detection, dose quantity adjustment, coffee grinder
blocked
No coffee
A low coffee bean level is detected by the Hall sensor,
after variations in the pulse frequency (with or without
coffee).
If there are no coffee beans (operation while empty),
the number of rotations – and therefore the number of
pulses – will be greater.
With beans n=100%
t1 = no coffee indication
Without beans n=100%
t1
t2
If, however, there are coffee beans, the number of
rotations will be lower due to the force created by the
grinding.
Without beans n=50%
t2 = no indication
t3
t4
t3 and t4 = this measurement is performed at the end
of each grinding process
Dose quantity adjustment
With beans n=50% The dose quantity is adjusted in accordance with the
pulses detected (number of rotations proportional to the
selected flavor – mild, medium or strong).
Coffee grinder blockage
If the coffee grinder becomes blocked for any reason,
pulses will no longer be transmitted to the electronic
t
system and the grinder will come to a stop.
Page 07 / 10
Downloaded from www.Manualslib.com manuals search engine
MINUTO
04 OPERATING LOGIC
4.10. Dose self-learning (SAS)
The aim of this function is to automatically regulate the average dose of ground coffee (SELFLEARNING); this takes place with an algorithm based on the following values and setting by the
user:
1. Number of coffee grinder pulses during the grinding cycle.
2. Max. average value of the power consumed by the gear motor during the coffee brewing cycle.
3. Aroma selected by the user.
The algorithm compares the maximum average value of the power consumed by the gear motor
with the value listed in the table for the selected aroma, in order to calculate the new grinding
pulse value for the next coffee produced.
If the power consumption value is less than the minimum current value, the grinding pulses will
be increased by 2.
If the power consumption value is greater than the maximum current value, the grinding pulses
will be decreased by 4.
If the power consumption value falls within the “over-torque” interval, the product will be dispensed and the grinding pulses will be decreased by 10.
If the power consumption value falls within the “abort cycle” interval, the dreg will be expelled
and the grinding pulses will be decreased by 10.
If the “pre-ground” flavour is selected by the user, no modification will be made.
This guarantees that, regardless of the coffee type used, the grinding level setting
and the wear on the grinders, the ground coffee dose always remains constant.
DOSE ADJUSTMENT (NUMBER OF GRINDER IMPULSES)
TO APPLY TO MED AROMA
A
Aroma
of the
grinded
product
3 levels
5 levels
Light
Very Light
Light
B
Med
Strong
0
-4
-10
-10 and
CYCLE
ABORTED
MAX_CURRENT_mA
<150mA
<=150mA
MAX_CURRENT_mA
<=250mA
MAX_CURRENT_mA
>250mA
MAX_CURRENT_mA
>800mA
MAX_CURRENT_mA
>1000mA
MAX_CURRENT_mA
<250mA
<=250mA
MAX_CURRENT_mA
<=350mA
MAX_CURRENT_mA
>350mA
MAX_CURRENT_mA
>800mA
MAX_CURRENT_mA
>1000mA
MAX_CURRENT_mA
<350mA
<=350mA
MAX_CURRENT_mA
<=500mA
MAX_CURRENT_mA
>500mA
MAX_CURRENT_mA
>800mA
MAX_CURRENT_mA
>1000mA
Med
Strong
C
+2
Very Strong
Important:
For perfect operation, machine adjustment should take place in the area of the fields
highlighted in green (A, B, C). When the type or brand of coffee is changed, there may be
variations in the size of the beans and their stickiness or roasting level. This leads to variations
in power consumption (mA), with resulting excessive or insufficient doses (until the necessary
adjustments have been made to compensate for this change).
Caution: In the case of excessive dosage, powder may be expelled into the dreg
drawer. This is not a fault, but can occur during preliminary operation or after a
service.
Page 08 / 10
Downloaded from www.Manualslib.com manuals search engine
MINUTO
04 OPERATING LOGIC
4.11. Water level detection (water tank)
“Water low” message (water reserve)
Water tank
Sensor
200 puls.
Function:
The water level is monitored by a capacitative sensor, located one
third of the way up the water tank wall.
If the electronics assembly detects, by means of the sensor,
that the amount of water in the tank has dropped below the
above mentioned level, a water reserve remains available for
the dispensing process underway (this will cover 200 flow meter
pulses).
The product dispensing process will then come to an end.
If a dispensing cycle ends after the sensor has been triggered (in
the reserve) then the display “Water low” continues to be displayed
during the following dispensing cycle.
4.12. Descaling request
“Descaling” – message with water filter
inserted
(appliances with display only)
Flow meter pulses
The water hardness is set on the basis of the
regional water hardness analysis
(1, 2, 3, 4).
Filter
on
Filter off:
If the function is turned off the electronics
assembly monitors the flow meter pulses,
recording one pulse each turn.
Filter
off
Filter on:
If the function is turned on the electronics
assembly monitors the flow meter pulses,
recording one pulse every two turns.
Number of pulses
360°
1 rev
“Change water filter” message
The electronics assembly uses the flow meter
impulses to keep track of the amount of water
which has flowed through; after the specified
amount (set in accordance with the water
hardness level), the “Replace filter” message
appears.
Page 09 / 10
Downloaded from www.Manualslib.com manuals search engine
MINUTO
04 OPERATING LOGIC
4.13. Water filter
Function:
• Reduced limescale deposits which take longer to form.
• Improved water quality.
• Improved taste due to the ideal water hardness.
Life span / descaling performance:
• - 10 ° dH
• 60 litres
• 2 months
Bypass
To achieve the best possible operating mode consistency
over the total life span, the water is channelled using
a 3-stage bypass (A, B, C) depending on the degree of
hardness. See small image.
Page 10 / 10
Downloaded from www.Manualslib.com manuals search engine
CHAPTER 5
TROUBLESHOOTING
MINUTO
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.1.1. Minuto Cappuccino test mode
To enter Test Mode
The machine enters Test Mode by holding pressed together Espresso and Menu buttons, while
switching on the machine by mean of the main switch on the backside of the CA. Once entered in
Test Mode, the display shows the firmware version.
The Test Mode is organized into 5 different pages:
Page 0: The display shows:
a) Firmware version.
b) Type.
c) Main supply voltage
d) Main supply frequency (50 or 60 Hz).
Page 1: Keyboard and display’s colour test:
a) Espresso button
b) Coffee button
c) Cappuccino button
d) Special button
e) Menu button
f) Aroma button
g) Stand-by button
h) Backlight colors
Page 2: Input signals test:
a) Water level sensor
b) Microswitch door closed/opened
c) Microswitch presence of the Brew Unit
d) Lever position on Espresso
e) Lever position on Drip
Page 3: Low voltage loads test:
a) Brew Unit movement upward and downward (24V DC)
Page 4: High/Low voltage loads test (Pump, E.Valve ) :
a) Pump (120-230V AC)
b) Electro Valve 1 (24Vdc) ( The door must be closed !!)
c) Electro Valve 2 (24Vdc) ( The door must be closed !!)
Page 5: High voltage loads test (Heater , Grinder ):
a) Heater (120-230V AC)
b) Grinder (170-320V DC)
Page 01 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
The user can change the page by pressing the STAND-BY button.
Page 0 is accessible only entering Test Mode from PowerOFF.
At the start up all loads are turned off.
TEST MODE Level0
Pressing button ON/OFF
TEST MODE Level1
Pressing button ON/OFF
TEST MODE Level2
Pressing button ON/OFF
Pressing button ON/OFF
TEST MODE Level3
Pressing button ON/OFF
TEST MODE Level4
Pressing button ON/OFF
TEST MODE Level5
Firmware Software version
Firmware version on the display.
The machine model is shown ( TOP).
The voltage of the main supply “230V/120V”
The frequency of the main supply is shown (50 or 60 Hz)
ERROR: If machine model is different from TOP, change the interface.
Press STAND_BY “
” to move to the next screen
The machine passes to the Page 1 (KEYBOARD)
ERROR: The page does not change; Check the interface
board and the flat cable (JP21)
Page 02 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Press buttons from 1 to 7
Only when a button is pressed a O appears on the relative position of
button pressed.
In the middle of display appears the name of the button pressed.
Pressing buttons on the left the backlight color changes from
GREEN to YELLOW.
Pressing button on the right the backlight color changes from
GREEN to RED.
When a button is pressed, also the Stand-By led (RED) turn ON.
Note: Press button STANDBY as the last once, since it makes
change the test page.
Note: If 2 or more buttons are pressed the name that appears
on display could be wrong.
ERROR: If nothing appears on display; check the interface board and the flat cable (JP21).
ERROR: If during the movement the backlight remain green check the wiring (JP1) from the interface board and the display
display..
ERROR: The name displayed is wrong; check the position of jumper in interface. It must be the
same of machine model:
· Jumper on JP5 for Focus machine model
· Jumper on JP6 for Class machine model
Press STAND_BY “
” to move to the next screen
The machine passes to the level 2 (INPUTS)
Insert a full Water Tank
The indication H20 changes from “N” to “Y”.
Note: the switching from “N” to “Y” requires about 1-2 seconds.
ERROR: The indication TANK-H2O doesn’t change; check the
capacitive sensor (fixing) and the wiring (JP23)
Insert the BrewUnit
The indications BU-P changes from “N” to “Y”.
Note: removing the BrewUnit the indication from “Y” to “N” requires
about 2-3 seconds to switch.
ERROR: Check the BU presence Microswitch and the wiring
(JP16).
Close the Door and Dreg Drawer
The indication DOOR change from “N” to “Y”
ERROR: The indication DOOR does not change; check
the Microswitch for the door and the wiring (JP14).
Note: without the Dreg Drawer correctly inserted the DOOR indication
cannot change!
Page 03 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Press STAND_BY “
” to move to the next screen
The machine passes to the Page 3 (BU PAGE)
Press the ESPRESSO button to move the BU to Work
IMPORTANT NOTE: If the DREGDRAWER is not inserted or the
DOOR is not closed the BU test cannot be performed. If these 2
inputs are not in the right position, a warning message will be
shown and the display turns to yellow.
When the BU reaches the work position the indication WORK
changes from “N” to “Y”, the number of the current is minus than
200mA (without BU) or 300mA (with BU).
ERROR: The indication WORK doesn’t change and remain “N”, the
display backlight changes from green to red; Check the work
microswitch (broken?), the BU motor (blocked?) and the wiring
(JP16).
ERROR: (Without BU) The absorbed current is more than 200mA,
the display backlight changes from green to red; check the BU and
the motor.
ERROR: (With BU)The absorbed current is more than 300mA, the
display backlight changes from green to red; check the BU and the
motor
Press the CAPPUCCINO button to move the BU to Home
When the BU reaches the home position the indication HOME
changes from “N” to “Y”, the number of the current is minus than
200mA (without BU) or 300mA (with BU).
ERROR: The indication HOME doesn’t change and remain “N”, the
display backlight changes from green to red; Check the work
microswitch (is broken), the BU motor (is blocked) and the wiring
(JP16).
ERROR: (Without BU) The absorbed current is higher than
200mA, the display backlight changes from green to red; check the
BU and the motor.
Page 04 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
ERROR: (With BU)The absorbed current is higher than 300mA, the
display backlight changes from green to red; check the BU and the
motor
Press STAND_BY “
” to move to the next screen
The machine passes to the Page 4 (EV - PUMP)
Press the ESPRESSO button to open the Electro Valve 1
IMPORTANT NOTE: If the DREGDRAWER is not inserted or the
DOOR is not closed the EV test cannot be performed. If these 2
inputs are not in the right position, a warning message will be
shown and the display turns to yellow.
It is possible to hear the “click” from Electro Valve. The indication
beside the EV1 changes from “OFF” to “ON”.
Press the COFFEE button to open the Electro Valve 2
It is possible to hear the “click” from Electro Valve. The indication
beside the EV2 changes from “OFF” to “ON”.
Press the STEAM button to switch on the pump
The water goes out from the pipe and the indication IMP shows
increasing numbers. The indication L/H must be within the range
10-18.
ERROR: The display backlight changes from green to red and the
impulse remains 0; If water comes out the pipe: check the wiring
from the flowmeter to the CPU/POWER board (JP5). If no water
comes out the pipe: check the pump and the wiring from the pump
to the CPU/POWER board (JP24).
ERROR: The L/H is zero or very low; the Electro Valve does not
open. Check the wiring from the Electro Valve to the CPU/POWER
board (JP3) and the Electro Valve.
Press STAND_BY “
” to move to the next screen
Page
Downloaded from www.Manualslib.com manuals search engine
05 / 46
MINUTO
05 TROUBLESHOOTING
The machine passes to the level 5 (Heater-Grinder)
Press the STEAM button to switch on the grinder
The grinder rotates and in the indication GRINDER the number increasing
up to 40. The other numbers inside the GRINDER box are not important
for this test.
ERROR: The number remains 0 or the grinder does not run, the display
backlight changes from green to red; check the Hall sensor board of the
Grinder, the Grinder, the wiring from the Hall sensor board to the CPU/
POWER board (JP2) and the wiring from the Grinder to the CPU/POWER
board (JP8)
Check the temperature
The number shows the heater temperature .
ERROR: In the indication HEATER appears “SHORT”, the NTC temperature-sensor is shorted, the display backlight changes from green to red;
check the wiring from the NTC temperature-sensor to the CPU/POWER
board (JP13).
ERROR: In the indication HEATER appears “OPEN”, the NTC temperature-sensor is detached or broken, the display backlight changes from
green to red; check the wiring from the NTC temperature-sensor to the
CPU/POWER board (JP13).
Press the ESPRESSO button to switch on the Heater
The absorbed current ( Amperometer on the main supply) is OK, the
indication HEATER changes from “OFF” to “ON” and the
temperature starts increasing.
If temperature is over 135°C, the backlight change from GREEN to
YELLOW. This is a ALERT message to avoid heating the HEATER element
over dangerous temperature.
ERROR: the absorbed current is KO or the temperature does not
increase; check the wiring from the heater to the CPU/POWER board
(JP19) and the wiring of the NTC temperature-sensor (JP13).
Page 06 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.1.2. SteamOut
To enter in SteamOut
The machine enters SteamOut mode by holding pressed together the COFFEE button and the
MENU button while switching on the machine
Once entered the Steam Out mode the display shows the “STEAM
OUT” indication. Buttons can be released
IMPORTANT NOTE: to execute the Steam-Out procedure the DREGDRAWER
must be in place and the DOOR must be closed.
If these 2 conditions are not respected a warning message is shown on the display and the Steam-Out is interrupted.
The machine starts the Steam Out and the display change the backlight (yellow)
and appears the indication “ON”.
While the Steam Out runs the Electrovalve is opened and water comes out the
Water/Steam pipe.
When the Steam Out is complete the message “COMPLETE” is shown on the
Display.The Electrovalve automatically closes and the machine can be switched
off.
When the Steam-Out is complete the following parameters are reset to their default values:
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Length Espresso product
Length Coffee product
Length Cappuccino (Coffee + Milk product)
Length Milk product
StandBy Time
Count Coffee
The request for Priming the Circuit at the first switch on is set.
Brewing Unit Empty
Aroma
Aroma Impulses
Filter Presence
Filter Pulses
Dynamic threshold
History of grindings for Beans Presence detection· Filter Presence
Page 07 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.2.1. Minuto Cappuccino test mode for USA
To enter Test Mode
The machine enters Test Mode by holding pressed together Espresso and Menu buttons, while
switching on the machine by mean of the main switch on the backside of the CA. Once entered in
Test Mode, the display shows the firmware version.
The Test Mode is organized into 5 different pages:
Page 0: The display shows:
a) Firmware version.
b) Type.
c) Main supply voltage
d) Main supply frequency (50 or 60 Hz).
Page 1: Keyboard and display’s colour test:
a) Espresso button
b) Medium Coffee button
c) Long Coffee button
d) Cappuccino button
e) Aroma button
f) Menu button
g) Stand-by button
h) Backlight colors
Page 2: Input signals test:
a) Water level sensor
b) Microswitch door closed/opened
c) Coffee Beans cover presence
d) Microswitch presence of the Brew Unit
e) Lever position on Espresso
f) Lever position on Drip
Page 3: Low voltage loads test:
a) Brew Unit movement upward and downward (24V DC)
Page 4: High/Low voltage loads test (Pump, E.Valve ) :
a) Pump (AC voltage)
b) Electro Valve (24Vdc) ( The door must be closed !!)
Page 5: High voltage loads test (Heater , Grinder ):
a) Heater (120-230V AC)
b) Grinder (170-320V DC)
Page
Downloaded from www.Manualslib.com manuals search engine
08 / 46
MINUTO
05 TROUBLESHOOTING
The user can change the page by pressing the STAND-BY button.
Page 0 is accessible only entering Test Mode from PowerOFF.
At the start up all loads are turned off.
TEST MODE Level0
Pressing button ON/OFF
TEST MODE Level1
Pressing button ON/OFF
TEST MODE Level2
Pressing button ON/OFF
Pressing button ON/OFF
TEST MODE Level3
Pressing button ON/OFF
TEST MODE Level4
Pressing button ON/OFF
TEST MODE Level5
Firmware Software version
Firmware version on the display.
The machine model is shown ( TOP).
The voltage of the main supply “230V/120V”
The frequency of the main supply is shown (50 or 60 Hz)
ERROR: If machine model is different from TOP, change the interface.
Press STAND_BY “
” to move to the next screen
The machine passes to the Page 1 (KEYBOARD)
ERROR: The page does not change; Check the interface
board and the flat cable (JP21)
Page
Downloaded from www.Manualslib.com manuals search engine
09 / 46
MINUTO
05 TROUBLESHOOTING
Press buttons from 1 to 7
Only when a button is pressed a O appears on the relative position of
button pressed.
In the middle of display appears the name of the button pressed.
Pressing buttons on the left the backlight color changes from
GREEN to YELLOW.
Pressing button on the right the backlight color changes from
GREEN to RED.
When a button is pressed, also the Stand-By led (RED) turn ON.
Note: Press button STANDBY as the last once, since it makes
change the test page.
Note: If 2 or more buttons are pressed the name that appears
on display could be wrong.
ERROR: If nothing appears on display; check the interface board and the flat cable (JP21).
ERROR: If during the movement the backlight remain green check the wiring (JP1) from the interface board and the display
display..
ERROR: The name displayed is wrong; check the position of jumper in interface. It must be the
same of machine model:
· Jumper on JP5 for Focus machine model
· Jumper on JP6 for Class machine model
Press STAND_BY “
” to move to the next screen
The machine passes to the level 2 (INPUTS)
Insert a full Water Tank
The indication H20 changes from “N” to “Y”.
Note: the switching from “N” to “Y” requires about 1-2 seconds.
ERROR: The indication TANK-H2O doesn’t change; check the
capacitive sensor (fixing) and the wiring (JP23)
Insert the BrewUnit
The indications BU-P changes from “N” to “Y”.
Note: removing the BrewUnit the indication from “Y” to “N” requires
about 2-3 seconds to switch.
ERROR: Check the BU presence Microswitch and the wiring
(JP16).
Close the Door and Dreg Drawer
The indication DOOR change from “N” to “Y”
ERROR: The indication DOOR does not change; check
the Microswitch for the door and the wiring (JP14).
Note: without the Dreg Drawer correctly inserted the DOOR indication
cannot change!
Page 10 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
The indications BEAN-C changes from “N” to “Y”.
ERROR: The indication BEAN-C does not change; check the reed for
the cover and the wiring (JP25).
Move Pressure Lever in COFFEE position
The indications DRIP changes from “N” to “Y”.
Move Pressure Lever in ESPRESSO position
The indication ESP change from “N” to “Y”.
IMPORTANT NOTE: If the Pressure Lever is not inserted (on
120V version) a warning message will be shown and the display turns
to yellow..
Check JP4 on interface board.
Press STAND_BY “
” to move to the next screen
The machine passes to the Page 3 (BU PAGE)
Press the ESPRESSO button to move the BU to Work
IMPORTANT NOTE: If the DREGDRAWER is not inserted or the
DOOR is not closed the BU test cannot be performed. If these 2
inputs are not in the right position, a warning message will be
shown and the display turns to yellow.
When the BU reaches the work position the indication WORK
changes from “N” to “Y”, the number of the current is minus than
200mA (without BU) or 300mA (with BU).
ERROR: The indication WORK doesn’t change and remain “N”, the
display backlight changes from green to red; Check the work
microswitch (broken?), the BU motor (blocked?) and the wiring
(JP16).
Page 11 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Press STAND_BY “
” to move to the next screen
ERROR: (Without BU) The absorbed current is more than 200mA,
the display backlight changes from green to red; check the BU and
the motor.
ERROR: (With BU)The absorbed current is more than 300mA, the
display backlight changes from green to red; check the BU and the
motor
Press the LONG COFFEE button to move the BU to Home
When the BU reaches the home position the indication HOME
changes from “N” to “Y”, the number of the current is minus than
200mA (without BU) or 300mA (with BU).
ERROR: The indication HOME doesn’t change and remain “N”, the
display backlight changes from green to red; Check the work
microswitch (is broken), the BU motor (is blocked) and the wiring
(JP16).
ERROR: (Without BU) The absorbed current is higher than
200mA, the display backlight changes from green to red; check the
BU and the motor.
ERROR: (With BU)The absorbed current is higher than 300mA, the
display backlight changes from green to red; check the BU and the
motor
Press STAND_BY “
” to move to the next screen
The machine passes to the Page 4 (EV - PUMP)
Press the ESPRESSO button to open the Electro Valve 1
IMPORTANT NOTE: If the DREGDRAWER is not inserted or the
DOOR is not closed the EV test cannot be performed. If these 2
inputs are not in the right position, a warning message will be
shown and the display turns to yellow.
Page 12 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
It is possible to hear the “click” from Electro Valve. The indication
beside the EV1 changes from “OFF” to “ON”.
Press the MEDIUM COFFEE button to open the Electro Valve 2
It is possible to hear the “click” from Electro Valve. The indication
beside the EV2 changes from “OFF” to “ON”.
Press the CAPPUCCINO button to switch on the pump
The water goes out from the pipe and the indication IMP shows
increasing numbers. The indication L/H must be within the range
10-18.
ERROR: The display backlight changes from green to red and the
impulse remains 0; If water comes out the pipe: check the wiring
from the flowmeter to the CPU/POWER board (JP5). If no water
comes out the pipe: check the pump and the wiring from the pump
to the CPU/POWER board (JP24).
ERROR: The L/H is zero or very low; the Electro Valve does not
open. Check the wiring from the Electro Valve to the CPU/POWER
board (JP3) and the Electro Valve.
Press STAND_BY “
” to move to the next screen
The machine passes to the level 5 (Heater-Grinder)
Press the CAPPUCCINO button to switch on the grinder
IMPORTANT NOTE: If the COFFEE BEANS Cover is not inserted
the Grinder test cannot be performed in 120V. If this input is not in
the right position, a warning message will be shown and the display
turns to yellow.
The grinder rotates and in the indication GRINDER the number
increasing up to 40. The other numbers inside the GRINDER box
are not important for this test.
Page 13 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
ERROR: The number remains 0 or the grinder does not run, the display
backlight changes from green to red; check the Hall sensor board of the
Grinder, the Grinder, the wiring from the Hall sensor board to the CPU/
POWER board (JP2) and the wiring from the Grinder to the CPU/POWER
board (JP8)
Check the temperature
The number shows the heater temperature .
ERROR: In the indication HEATER appears “SHORT”, the NTC temperature-sensor is shorted, the display backlight changes from green to red;
check the wiring from the NTC temperature-sensor to the CPU/POWER
board (JP13).
ERROR: In the indication HEATER appears “OPEN”, the NTC temperature-sensor is detached or broken, the display backlight changes from
green to red; check the wiring from the NTC temperature-sensor to the
CPU/POWER board (JP13).
Press the ESPRESSO button to switch on the Heater
The absorbed current ( Amperometer on the main supply) is OK, the
indication HEATER changes from “OFF” to “ON” and the
temperature starts increasing.
If temperature is over 100°C, the backlight change from GREEN to
YELLOW. This is a ALERT message to avoid heating the HEATER element
over dangerous temperature.
ERROR: the absorbed current is KO or the temperature does not
increase; check the wiring from the heater to the CPU/POWER board
(JP19) and the wiring of the NTC temperature-sensor (JP13).
Page 14 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.2.2. SteamOut
To enter in SteamOut
The machine enters SteamOut mode by holding pressed together the MEDIUM COFFEE button
and the MENU button while switching on the machine
Once entered the Steam Out mode the display shows the “STEAM
OUT” indication. Buttons can be released
IMPORTANT NOTE: to execute the Steam-Out procedure the DREGDRAWER
must be in place and the DOOR must be closed.
If these 2 conditions are not respected a warning message is shown on the display and the Steam-Out is interrupted.
The machine starts the Steam Out and the display change the backlight (yellow)
and appears the indication “ON”.
While the Steam Out runs the Electrovalve is opened and water comes out the
Water/Steam pipe.
When the Steam Out is complete the message “COMPLETE” is shown on the
Display.The Electrovalve automatically closes and the machine can be switched
off.
When the Steam-Out is complete the following parameters are reset to their default values:
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Length Espresso product
Length Medium Coffee product
Length Large coffee product
Length Milk product
StandBy Time
Count Coffee
The request for Priming the Circuit at the first switch on is set.
Brewing Unit Empty
Aroma
Aroma Impulses
Filter Presence
Filter Pulses
Dynamic threshold
History of grindings for Beans Presence detection· Filter Presence
Page 15 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.3.1. Minuto Focus/Class test mode
ON/OFF button
To enter Test Mode
The machine enters Test Mode by holding pressed together Espresso and Menu buttons (or CalcClean button in Focus version) while switching on the machine by mean of the main switch on the
backside of the CA. Once entered in Test Mode, the display shows the firmware version.
The Test Mode is organized into 5 different pages :
Page 0: The display shows:
a) Firmware version.
b) CLASS or FOCUS type.
c) “120” if the machine is a 120V model.
d) Main supply frequency (50 or 60 Hz).
Page 1: Keyboard and display’s colour test:
a) Espresso button
b) Cafè Crème button
c) Steam button
d) Water button
e) Menu button (or CalcClean button in FOCUS version)
f) Aroma button
g) Stand-by button
h) Backlight colors
Page 2: Input signals test:
a) Water level sensor
b) Microswitch door closed/opened
c) Microswitch presence of the Brew Unit
d) Lever position on Espresso
e) Lever position on Drip
Page 3: Low voltage loads test:
a) Brew Unit movement upward and downward (24V DC)
Page 4: High/Low voltage loads test (Pump, E.Valve ) :
a) Pump (120-230V AC)
b) Electro Valve (24Vdc) ( The door must be closed !!)
Page 5: High voltage loads test (Heater , Grinder ):
a) Heater (120-230V AC)
b) Grinder (170-320V DC)
Page 16 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Firmware Software version
Firmware version on the display.
The machine model is shown ( FOCUS or CLASS).
The voltage of the main supply “230V/120V”
The frequency of the main supply is shown (50 or 60 Hz)
ERROR: If machine model is different from CLASS or FOCUS, change the interface.
Press STAND_BY “
” to move to the next screen
Operational check – keys
Start condition
Only when a button is pressed a O appears on the relative position of button pressed.
In the middle of display appears the name of the button pressed.
Pressing buttons on the left the backlight color changes from GREEN to
YELLOW.
Pressing button on the right the backlight color changes from GREEN to
RED.
When a button is pressed, also the Stand-By led (RED) turn ON.
Note: Press button STANDBY as the last once, since it makes change the
test page.
Note: If 2 or more buttons are pressed the name that appears on display
could be wrong.
ERROR:
If nothing appears on display; check the interface board and the flat cable (JP21).
If during the movement the backlight remain green check the wiring (JP1) from the interface
board and the display.
The name displayed is wrong; check the position of
jumper in interface. It must be the same of machine model:
· Jumper on JP5 for Focus machine model
· Jumper on JP6 for Class machine model
Press STAND_BY “
” to move to the next screen
Page 17 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Operational check microswitches and sensors
Start condition
Insert a full Water Tank
The indication H20 changes from “N” to “Y”.
NOTE: the switching from “N” to “Y” requires about 1-2 seconds.
ERROR: The indication TANK-H2O doesn’t change; check the
capacitive sensor (fixing) and the wiring (JP23)
Insert the BrewUnit
The indications BU-P changes from “N” to “Y”.
NOTE: removing the BrewUnit the indication from “Y” to “N” requires
about 2-3 seconds to switch.
ERROR: Check the BU presence Microswitch and the wiring (JP16).
Close the Door and Dreg Drawer
The indication DOOR change from “N” to “Y”
ERROR: The indication DOOR does not change; check the
Microswitch for the door and the wiring (JP14). NOTE: without the Dreg
Drawer correctly inserted the DOOR indication cannot
change !
Move Pressure Lever in DRIP position (120V only)
The indications DRIP changes from “N” to “Y”. (120V only)
Move Pressure Lever in ESPRESSO position (120V only)
The indication ESP change from “N” to “Y”. (120V only)
IMPORTANT NOTE: If the Pressure Lever is not inserted (on
120V version) a warning message will be shown and the display
turns to yellow..
Check JP4 on interface board.
Press the STAND-BY button
The machine passes to the Page 3 (BU PAGE)
Press STAND_BY “
” to move to the next screen
Page 18 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Operational check – brewing unit
Start condition
Press the ESPRESSO button to move the BU to Work
IMPORTANT NOTE: If the DREGDRAWER is not inserted or the
DOOR is not closed the BU test cannot be performed. If these 2
inputs are not in the right position, a warning message will be
shown and the display turns to yellow..
When the BU reaches the work position the indication WORK
changes from “N” to “Y”, the number of the current is minus than
200mA (without BU) or 300mA (with BU).
ERROR: The indication WORK doesn’t change and remain “N”, the
display backlight changes from green to red; Check the work microswitch
(broken?), the BU motor (blocked?) and the wiring (JP16)
ERROR: (Without BU) The absorbed current is more than 200mA,
the display backlight changes from green to red; check the BU and
the motor.
ERROR: (With BU) The absorbed current is more than 300mA, the
display backlight changes from green to red; check the BU and the
motor
Press the AROMA button to move the BU to Home
When the BU reaches the home position the indication HOME
changes from “N” to “Y”, the number of the current is minus than
200mA (without BU) or 300mA (with BU).
ERROR: The indication HOME doesn’t change and remain “N”, the
display backlight changes from green to red; Check the work
microswitch (is broken), the BU motor (is blocked) and the wiring
(JP16).
ERROR: (Without BU) The absorbed current is higher than
200mA, the display backlight changes from green to red; check the
BU and the motor.
ERROR: (With BU) The absorbed current is higher than 300mA, the
display backlight changes from green to red; check the BU and the
motor
Press STAND_BY “
” to move to the next screen
Page 19 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Operational check - solenoid valves and pump
Start condition
Press the ESPRESSO button to open the Electro Valve
IMPORTANT NOTE: If the DREGDRAWER is not inserted or the DOOR is not
closed the EV test cannot be performed. If these 2 inputs are not in the
right position, a warning message will be shown and the display turns to
yellow.
It is possible to hear the “click” from Electro Valve. The indication beside
the EV1 changes from “OFF” to “ON”.
Press the STEAM button to switch on the pump
The water goes out from the pipe and the indication IMP shows
increasing numbers. The indication L/H must be within the range 10-18.
ERROR: The display backlight changes from green to red and the
impulse remains 0; If water comes out the pipe: check the wiring from the
flowmeter to the CPU/POWER board (JP5). If no water comes out the pipe:
check the pump and the wiring from the pump to the CPU/POWER board
(JP24).
ERROR: The L/H is zero or very low; the Electro Valve does not
open. Check the wiring from the Electro Valve to the CPU/POWER
board (JP3) and the Electro Valve.
Press STAND_BY “
” to move to the next screen
Operational check - coffee grinder and boiler
Initial status
Press the STEAM button to switch on the grinder
The grinder rotates and in the indication GRINDER the number
increasing up to 40. The other numbers inside the GRINDER box are not
important for this test.
ERROR: The number remains 0 or the grinder does not run, the
display backlight changes from green to red; check the Hall sensor
board of the Grinder, the Grinder, the wiring from the Hall sensor
board to the CPU/POWER board (JP2) and the wiring from the
Grinder to the CPU/POWER board (JP8)
Page 20 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Check the temperature
The number shows the heater temperature .
ERROR: In the indication HEATER appears “SHORT”, the NTC
temperature-sensor is shorted, the display backlight changes from
green to red; check the wiring from the NTC temperature-sensor to
the CPU/POWER board (JP13).
ERROR: In the indication HEATER appears “OPEN”, the NTC
temperature-sensor is detached or broken, the display backlight
changes from green to red; check the wiring from the NTC
temperature-sensor to the CPU/POWER board (JP13).
Press the ESPRESSO button to switch on the Heater
The absorbed current ( Amperometer on the main supply) is OK, the
indication HEATER changes from “OFF” to “ON” and the temperature starts
increasing.
If temperature is over 135°C, the backlight change from GREEN to
YELLOW. This is a ALERT message to avoid heating the HEATER
element over dangerous temperature.
ERROR: the absorbed current is KO or the temperature does not
increase; check the wiring from the heater to the CPU/POWER
board (JP19) and the wiring of the NTC temperature-sensor (JP13).
Page 21 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.3.2. SteamOut
ON/OFF button
To enter in SteamOut
The machine enters SteamOut mode by holding pressed together the CAFE’ CREME button and
the MENU/CALC CLEAN button while switching on the machine.
Once entered the Steam Out mode the display shows the “STEAM
OUT” indication. Buttons can be released
IMPORTANT NOTE: to execute the Steam-Out procedure the
DREGDRAWER must be in place and the DOOR must be closed.
If these 2 conditions are not respected a warning message is shown
on the display and the Steam-Out is interrupted.
The machine starts the Steam Out and the display change the
backlight (yellow) and appears the indication “ON”.
While the Steam Out runs the Electrovalve is opened and water
comes out the Water/Steam pipe.
When the Steam Out is complete the message “COMPLETE” is
shown on the Display.The Electrovalve automatically closes and the
machine can be switched off.
When the Steam-Out is complete the following parameters are reset to their default values:
Count Coffee
Aroma
Length Espresso product
Length Coffee product
Filter Presence
Filter Pulses
Aroma Impulses
Dynamic threshold
History of grindings for Beans Presence detection
StandBy Time
The request for Priming the Circuit at the first switch on is set.
Page
Downloaded from www.Manualslib.com manuals search engine
22 / 46
MINUTO
05 TROUBLESHOOTING
5.4.1. Minuto Focus/Class test mode for USA
CLASS
for USA
FOCUS
for USA
Z4
Z5
Z6
Z1
Z2
Z3
Z4
Z5
Z6
Z7
To enter Test Mode
The machine enters Test Mode by holding pressed together Z1 and Z6 buttons (or Cleaning cycle
button in Focus version) while switching on the machine by mean of the main switch on the backside of the CA. Once entered in Test Mode, the display shows the firmware version.
The Test Mode is organized into 5 different pages :
Page 0: The display shows:
a) Firmware version.
b) CLASS or FOCUS type.
c) Voltage supply.
d) Main supply frequency.
Page 1: Keyboard and display’s colour test:
a) Z1 button
b) Z2 button
c) Z3 button
d) Z4 button
e) Z5 button
f) Z6 button
g) Z7 button
h) Backlight colors
Page 2: Input signals test:
a) Water level sensor
b) Microswitch door closed/opened
c) Microswitch presence of the Brew Unit
d) Lever position on Espresso
e) Lever position on Drip
Page 3: Low voltage loads test:
a) Brew Unit movement upward and downward (24V DC)
Page 4: High/Low voltage loads test (Pump, E.Valve ) :
a) Pump (AC voltage)
b) Electro Valve (24Vdc) ( The door must be closed !!)
Page 5: High voltage loads test (Heater , Grinder ):
a) Heater (120-230V AC)
b) Grinder (170-320V DC)
Page
Downloaded from www.Manualslib.com manuals search engine
23/ 46
MINUTO
05 TROUBLESHOOTING
Firmware Software version
Firmware version on the display.
The machine model is shown ( FOCUS or CLASS).
The voltage of the main supply “230V/120V”
The frequency of the main supply is shown (50 or 60 Hz)
ERROR: If machine model is different from CLASS or FOCUS, change the interface.
Press STAND_BY “
” to move to the next screen
Operational check – keys
Start condition
Only when a button is pressed a O appears on the relative position of button pressed.
In the middle of display appears the name of the button pressed.
Pressing buttons on the left the backlight color changes from GREEN to
YELLOW.
Pressing button on the right the backlight color changes from GREEN to
RED.
When a button is pressed, also the Stand-By led (RED) turn ON.
Note: Press button STANDBY as the last once, since it makes change the
test page.
Note: If 2 or more buttons are pressed the name that appears on display
could be wrong.
ERROR:
If nothing appears on display; check the interface board and the flat cable (JP21).
If during the movement the backlight remain green check the wiring (JP1) from the interface
board and the display.
The name displayed is wrong; check the position of
jumper in interface. It must be the same of machine model:
· Jumper on JP5 for Focus machine model
· Jumper on JP6 for Class machine model
Press STAND_BY “
” to move to the next screen
Page
Downloaded from www.Manualslib.com manuals search engine
24 / 46
MINUTO
05 TROUBLESHOOTING
Start condition
Insert a full Water Tank
The indication H20 changes from “N” to “Y”.
NOTE: the switching from “N” to “Y” requires about 1-2 seconds.
ERROR: The indication TANK-H2O doesn’t change; check the
capacitive sensor (fixing) and the wiring (JP23)
Insert the BrewUnit
The indications BU-P changes from “N” to “Y”.
NOTE: removing the BrewUnit the indication from “Y” to “N” requires
about 2-3 seconds to switch.
ERROR: Check the BU presence Microswitch and the wiring (JP16).
Close the Door and Dreg Drawer
The indication DOOR change from “N” to “Y”
ERROR: The indication DOOR does not change; check the
Microswitch for the door and the wiring (JP14). NOTE: without the Dreg
Drawer correctly inserted the DOOR indication cannot
change !
Insert the Coffee Beans Cover (120V NA only)
The indications BEAN-C changes from “N” to “Y”.
ERROR: The indication BEAN-C does not change; check the reed for the
cover and the wiring (JP25).
Move Pressure Lever in DRIP position
The indications DRIP changes from “N” to “Y”.
Move Pressure Lever in ESPRESSO position
The indication ESP change from “N” to “Y”.
IMPORTANT NOTE: If the Pressure Lever is not inserted (on
120V version) a warning message will be shown and the display
turns to yellow..
Check JP4 on interface board.
Press the STAND-BY button
The machine passes to the Page 3 (BU PAGE)
Press STAND_BY “
” to move to the next screen
Page
Downloaded from www.Manualslib.com manuals search engine
25 / 46
MINUTO
05 TROUBLESHOOTING
Operational check – brewing unit
Start condition
Press the Z1 button to move the BU to Work
IMPORTANT
NOTE: If the DREGDRAWER is not inserted or the
DOOR is not closed the BU test cannot be performed. If these 2
inputs are not in the right position, a warning message will be
shown and the display turns to yellow..
When the BU reaches the work position the indication WORK
changes from “N” to “Y”, the number of the current is minus than
200mA (without BU) or 300mA (with BU).
ERROR: The indication WORK doesn’t change and remain “N”, the
display backlight changes from green to red; Check the work microswitch
(broken?), the BU motor (blocked?) and the wiring (JP16)
ERROR: (Without BU) The absorbed current is more than 200mA,
the display backlight changes from green to red; check the BU and
the motor.
ERROR: (With BU) The absorbed current is more than 300mA, the
display backlight changes from green to red; check the BU and the
motor
Press the Z3 button to move the BU to Home
When the BU reaches the home position the indication HOME
changes from “N” to “Y”, the number of the current is minus than
200mA (without BU) or 300mA (with BU).
ERROR: The indication HOME doesn’t change and remain “N”, the
display backlight changes from green to red; Check the work
microswitch (is broken), the BU motor (is blocked) and the wiring
(JP16).
ERROR: (Without BU) The absorbed current is higher than
200mA, the display backlight changes from green to red; check the
BU and the motor.
ERROR: (With BU) The absorbed current is higher than 300mA, the
display backlight changes from green to red; check the BU and the
motor
Press STAND_BY “
” to move to the next screen
Page
Downloaded from www.Manualslib.com manuals search engine
26/ 46
MINUTO
05 TROUBLESHOOTING
Operational check - solenoid valves and pump
Start condition
Press the Z1 button to open the Electro Valve
IMPORTANT NOTE: If the DREGDRAWER is not inserted or the DOOR is not
closed the EV test cannot be performed. If these 2 inputs are not in the
right position, a warning message will be shown and the display turns to
yellow.
It is possible to hear the “click” from Electro Valve. The indication beside
the EV1 changes from “OFF” to “ON”.
Press the Z4 button to switch on the pump
The water goes out from the pipe and the indication IMP shows
increasing numbers. The indication L/H must be within the range 10-18.
ERROR: The display backlight changes from green to red and the impulse
remains 0; If water comes out the pipe: check the wiring from the flowmeter
to the CPU/POWER board (JP5). If no water comes out the pipe: check the
pump and the wiring from the pump to the CPU/POWER board (JP24).
ERROR: The L/H is zero or very low; the Electro Valve does not
open. Check the wiring from the Electro Valve to the CPU/POWER
board (JP3) and the Electro Valve.
Press STAND_BY “
” to move to the next screen
Operational check - coffee grinder and boiler
Initial status
Press the Z4 button to switch on the grinder
IMPORTANT NOTE: If the COFFEE BEANS Cover is not inserted the Grinder
test cannot be performed in 120V. If this input is not in the right position, a
warning message will be shown and the display turns to yellow.
The grinder rotates and in the indication GRINDER the number increasing
up to 40. The other numbers inside the GRINDER box are not important for
this test.
ERROR: The number remains 0 or the grinder does not run, the display
backlight changes from green to red; check the Hall sensor board of the
Grinder, the Grinder, the wiring from the Hall sensor board to the
CPU/POWER board (JP2) and the wiring from the Grinder to the
CPU/POWER board (JP8)
Page 27 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Check the temperature
The number shows the heater temperature .
ERROR: In the indication HEATER appears “SHORT”, the NTC
temperature-sensor is shorted, the display backlight changes from
green to red; check the wiring from the NTC temperature-sensor to
the CPU/POWER board (JP13).
ERROR: In the indication HEATER appears “OPEN”, the NTC
temperature-sensor is detached or broken, the display backlight
changes from green to red; check the wiring from the NTC
temperature-sensor to the CPU/POWER board (JP13).
Press the Z1 button to switch on the Heater
The absorbed current ( Amperometer on the main supply) is OK, the
indication HEATER changes from “OFF” to “ON” and the temperature starts
increasing.
If temperature is over 135°C, the backlight change from GREEN to
YELLOW. This is a ALERT message to avoid heating the HEATER
element over dangerous temperature.
ERROR: the absorbed current is KO or the temperature does not
increase; check the wiring from the heater to the CPU/POWER
board (JP19) and the wiring of the NTC temperature-sensor (JP13).
Page 28 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.4.2. SteamOut
CLASS
for USA
FOCUS
for USA
Z4
Z5
Z6
Z1
Z2
Z3
Z4
Z5
Z6
Z7
To enter in SteamOut
The machine enters SteamOut mode by holding pressed together the Z2 button and the Z6 button
while switching on the machine.
Once entered the Steam Out mode the display shows the “STEAM
OUT” indication. Buttons can be released
IMPORTANT NOTE: to execute the Steam-Out procedure the
DREGDRAWER must be in place and the DOOR must be closed.
If these 2 conditions are not respected a warning message is shown
on the display and the Steam-Out is interrupted.
The machine starts the Steam Out and the display change the
backlight (yellow) and appears the indication “ON”.
While the Steam Out runs the Electrovalve is opened and water
comes out the Water/Steam pipe.
When the Steam Out is complete the message “COMPLETE” is
shown on the Display.The Electrovalve automatically closes and the
machine can be switched off.
When the Steam-Out is complete the following parameters are reset to their default values:
Count Coffee
Aroma
Length Espresso product
Length Medium Coffee product
Filter Presence
Filter Pulses
Aroma Impulses
Dynamic threshold
History of grindings for Beans Presence detection
StandBy Time
The request for Priming the Circuit at the first switch on is set.
Page 29 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.5.1. Minuto Pure test mode
To enter Test Mode
The machine enters Test Mode by holding pressed together Espresso and CalcClean buttons while
switching on the machine by mean of the main switch on the backside of the CA.
Once entered shows Led Coffee Single, Led Coffee Double flashing in series (Level 0).
There are 6 different level, in each level the coffee-machine can execute different commands,
Level 0: Entry Level:
a) In this level can be done Reset to default
Level 1: The machine can test the button:
a) Button Espresso
b) Button Coffee
c) Button Calc_Clean
d) No Water LED
e) Alarm General LED
f) Decale LED
g) Rinsing LED
h) Drip Tray/Coffee Dreg Drawer LED
i) No Beans LED
Level 2: The machine can test other input signal:
a) Microswitch door closed/opened
b) Microswitch present of the brewing unit
c) Microswitch present of the dregdrawer
Level 3: The machine can test the loads in low voltage:
a) Brew Unit movement upward and downward (24V DC)
Level 4: The machine can test the load in high voltage:
a) Pump (100-120-230V AC)
a. Brew Unit must be in inserted and in Work position.
Level 5: The machine can test two loads in high voltage (Heater , Grinder):
a) Heater (100-120-230V AC)
b) Grinder (140-170-320V DC)
Page 30 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
The user can switch the level by pressing the Button ON/OFF, the machine shows the level of the
test:
a) Level 1: Led Espresso ON (G), Led Stand-by ON (R)
b) Level 2: Led Espresso ON (G), Led Descale ON (O)
c) Level 3: Led Espresso ON (G), Led Descale ON (O), Led CalcClean ON (O)
d) Level 4: Led Espresso ON (G), Led Descale ON (O), Led CalcClean ON (O), Led Rinsing ON (O)
e) Level 5: Led Espresso ON (G), Led Descale ON (O), Led CalcClean ON (O), Led Rinsing ON
(O), Led Coffee ON (G).
Legend:
(O) = Orange
(G) = Green
(R) = Red
TEST MODE Level0
Pressing button ON/OFF
TEST MODE Level1
Pressing button ON/OFF
TEST MODE Level2
Pressing button ON/OFF
TEST MODE Level3
Pressing button ON/OFF
Pressing button ON/OFF
TEST MODE Level4
Pressing button ON/OFF
TEST MODE Level5
At the start up all loads are turned off. The software allow to have only one load active at the same
time.
Level 0 (Start Test mode)
Start condition: NO BU, NO drag drawer, door open, No
Water sensor
LED INDICATION
Led Espresso
Led Coffee
Blink Alternately
Press BUTTON ON/OFF to move to the next screen
Page 31 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
Level 1 (Key)
05 TROUBLESHOOTING
Start condition: NO BU, NO drag drawer,
door open and No Water sensor
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Led
Descale
Led
Rinsing
OFF
OFF
OFF
OFF
OFF
OFF
Led
Descale
Led
Rinsing
Led
Descale
Led
Rinsing
Press Espresso Button
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
OFF
ON
ON
ERROR: Led NoWater remains off, check
the interface board and flat cable (JP21)
OFF
ON
ERROR: Led GenAlarm remains off, check
the interface board and flat cable (JP21)
ON
OFF
ERROR: Led NoWater & GenAlarm remain
off, check the interface board and flat cable
(JP21)
OFF
OFF
Switch on Red Leds NoWater & GenAlarm
Led
Dreg
Press CalcCLean Button
Action by user
LED INDICATION
Switch on Orange Leds Descale & Rinsing
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
OFF
OFF
OFF
ON
ON
ERROR: Led Descale remains off, check the
interface board and flat cable (JP21)
OFF
ON
ERROR: Led Rinsing remains off, check the interface board and flat cable (JP21)
ON
OFF
ERROR: Led Descale & Rinsing remain off,
check the interface board and flat cable
(JP21)
OFF
OFF
Led
Descale
Led
Rinsing
Press Coffee Button
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Switch on Red Leds Dreg & NoBeans
ON
OFF
OFF
ON
ERROR: Led NoBeans remains off, check
the interface board and flat cable (JP21)
OFF
ON
ERROR: Led Dreg remains off, check the
interface board and flat cable (JP21)
ON
OFF
ERROR: Led NoBeans & Dreg remain off,
check the interface board and flat cable
(JP21)
OFF
OFF
Finish condition: NO BU, NO drag drawer,
door open and No Water sensor
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Led
Descale
Led
Rinsing
OFF
OFF
OFF
OFF
OFF
OFF
Press BUTTON ON/OFF to move to the next screen
Page
Downloaded from www.Manualslib.com manuals search engine
32 / 46
MINUTO
Level 2 (Input)
05 TROUBLESHOOTING
Start condition: NO BU, NO drag drawer, door open and
No Water sensor
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
ON
ON
ON
Insert a full Water Tank
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Switch off Red Leds NoWater
NA
OFF
NA
NA
ERROR: Led NoWater remains on, check the capacitive
sensor (fixing) and the wiring (JP23)
NA
ON
NA
NA
Insert the Brew Unit
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Switch off Red Leds GenAlarm
NA
NA
OFF
NA
ERROR: Led GenAlarm remains on, check the BU presence Microswitch and the wiring (JP16).
NA
NA
ON
NA
Close the door and Dreg Drawer
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Switch off Red Led Dreg
NA
NA
NA
OFF
ERROR: Led Dreg remains on, check the Microswitch for
the door and the wiring (JP14). NOTE: without the Dreg
Drawer correctly inserted the DOOR indication cannot
change!
NA
NA
NA
ON
Finish condition: With BU, Drag Drawer, door closed
and Tank
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
OFF
OFF
OFF
Press BUTTON ON/OFF to move to the next screen
Level 3 (Brewing unit)
Start condition: NO BU, Drag drawer, door
Closed and No Water sensor
If the DREGDRAWER is not inserted or the
DOOR is not closed the BU test cannot be
performed. If these 2 inputs are not in the right
position, Led Dreg will be RED
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
OFF
OFF
OFF
NA
NA
NA
ON
Page 33 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Press the Espresso button to move BU to work
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
When the BU reaches the work position the
Led NoBeans is switched on
ON
NA
NA
NA
ERROR: Led Dreg remains on, check the Microswitch for
the door and the wiring (JP14). NOTE: without the Dreg
Drawer correctly inserted the DOOR indication cannot
change!
NA
NA
NA
NA
ERROR: led GenAlarm Switch ON; the
absorbed current is much more 300mA (with
BU) or 200mA (without BU) check the BU
and the motor
NA
NA
ON
NA
Press the Coffee button to move BU to home
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
When the BU reaches the work position the
Led NoBeans is switched on
ON
NA
NA
NA
ERROR: Led NoBeans remains off, Check
the work microswitch (broken?), the BU motor
(blocked?) and the wiring
(JP16).
NA
NA
NA
NA
ERROR: led GenAlarm Switch ON; the
absorbed current is much more 300mA (with
BU) or 200mA (without BU) check the BU
and the motor
NA
NA
ON
NA
Finish condition: With BU, Drag Drawer,
door closed
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led Dreg
OFF
OFF
OFF
OFF
Press BUTTON ON/OFF to move to the next screen
Level 4 (Pump)
Start condition: BU inserted, Drag drawer,
door Closed and No Water sensor
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
OFF
OFF
OFF
If the DREGDRAWER is not inserted or the
DOOR is not closed the BU cannot be moved
in work position and test cannot be performed.
If these 2 inputs are not in the right position,
Led Dreg will be RED
NA
NA
NA
ON
If the BU is not inserted, the test will not be
performed, so Led GenAlarm will be switched
ON
NA
NA
ON
NA
Page 34 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Press the Espresso button to move BU to work
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
When the BU reaches the work position the
Led NoBeans is switched on
ON
NA
NA
NA
ERROR: Led NoBeans remains off, Check the work microswitch (broken?), the BU motor (blocked?) and the wiring (JP16).
NA
NA
NA
NA
Press the Coffee button to switch on the Pump
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
The water goes out from the dispensing spout,the NoWater LED blink every Flowmeter pulse
NA
BLINK
NA
NA
ERROR: the NoWater LED does’t flashing
and after 5sec this LED Switch ON; check:
1) the BU is in work position,
2) pump,
3) the flowmeter,
4) the wiring from the flowmeter to the CPU/POWER board (JP5)
5) the wiring from the pump to the CPU/POWER board
(JP24)
NA
ON
NA
NA
Press the Espresso button to move BU to Home
Action by user
LED INDICATION
When the BU leave the work position the Led
NoBeans is switched off, and BU move to
Home Position to end L4 Test
Finish condition: With BU, Drag Drawer,
door closed
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
NA
NA
NA
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led Dreg
OFF
OFF
OFF
OFF
Press BUTTON ON/OFF to move to the next screen
Level 5 (Grinder-Heater)
Start condition: NO BU, NO drag drawer,
door open and No Water sensor
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
OFF
OFF
OFF
Page 35 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Check the Temperature
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
The red led General Alarm remains OFF
NA
NA
OFF
NA
ERROR: The temperature sensor is shorted or opened,
the led GenAlarm switch ON; check the wiring from the
heater to the CPU/POWER board (JP13).
NA
NA
ON
NA
Press the Espresso button to switch on the Heater
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
The user checkers that the absorbed current is OK
NA
NA
OFF
NA
ERROR: the absorbed current is KO; check the wiring
from the heater to the CPU/POWER board (JP17-3) and
the other wiring
NA
NA
OFF
NA
ERROR: If temperature is over 100°C, the NoWater LED
turn ON. This is a ALERT message to avoid heating the
HEATER element over dangerous temperature; and
Heater test cannot be performed.
ON
Press the Coffee button to switch on the Grinder
Action by user
The grinder rotates and Led NoBeans Blink
ERROR: the led NoBeans remains OFF and after the led
NoBeans switch ON; check the hall sensor board in the
Grinder, the Grinder, the wiring from the hall sensor
board to the CPU/POWER board (JP2) and the wiring from
the Grinder to the CPU/POWER board (JP8)
Finish condition: With BU, Drag Drawer,
door closed
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
BLINK
NA
OFF
NA
ON
NA
OFF
NA
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led Dreg
OFF
OFF
OFF
OFF
LED INDICATION
Page 36 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.5.2. SteamOut
To enter in SteamOut
The machine enters SteamOut mode by holding pressed together the COFFEE button and the
CALC_CLEAN button while switching on the machine.
Once entered shows Led Descale and Led Rinsing flashing in series.
If brewing unit is not inserted in the machine, LED General Alarm will be switched on.
If Door is opened or drag drawer is removed LED WASTE FULL will be switched on.
In these 2 conditions Brewing Unit cannot be moved at work so SteamOut will not be performed;
After Brewing Unit reach work position SteamOut start.
At the end of procedure Brewing Unit will be moved to rest position and LED ESPRESSO and LED
COFFEE turns on.
When the Steam-Out is complete the following parameters are reset to their default values:
·
·
·
·
·
·
·
·
·
·
·
Count Coffee
Aroma
Length Espresso product
Length Coffee product
Filter Presence
Filter Pulses
Aroma Impulses
Dynamic threshold
History of grindings for Beans Presence detection
StandBy Time
The request for Priming the Circuit at the first switch on is set.
Page 37 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.6.1. Minuto Pure test mode for USA
To enter Test Mode
The machine enters Test Mode by holding pressed together Espresso and CalcClean buttons while
switching on the machine by mean of the main switch on the backside of the CA.
Once entered shows Led Coffee Single, Led Coffee Double flashing in series (Level 0).
There are 6 different level, in each level the coffee-machine can execute different commands,
Level 0: Entry Level:
a) In this level can be done Reset to default
Level 1: The machine can test the button:
a) Button Espresso
b) Button Coffee
c) Button Steam
d) Button Hot Water
e) Button Calc_Clean
f) No Water LED
g) Alarm General LED
h) Drip Tray/Coffee Dreg Drawer LED
i) No Beans LED
j) Decale LED
k) Rinsing LED
Level 2: The machine can test other input signal:
a) Microswitch door closed/opened & dregdrawer
b) Microswitch present of the brewing unit
c) Water sensor
d) Coffee beans cover sensor
Level 3: The machine can test the loads in low voltage:
a) Brew Unit movement upward and downward (24V DC)
Level 4: The machine can test:
a) Pump (100-120 AC)
a. Electro-valve.
Level 5: The machine can test two loads in high voltage (Heater , Grinder):
a) Heater (100-120 AC)
b) Grinder (140-170 DC)
Page 38 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
The user can switch the level by pressing the Button ON/OFF, the machine shows the level of the
test:
a) Level 1: Led Espresso ON (G), Led Stand-by ON (R)
b) Level 2: Led Espresso ON (G), Led Descale ON (O)
c) Level 3: Led Espresso ON (G), Led Descale ON (O), Led CalcClean ON (O)
d) Level 4: Led Espresso ON (G), Led Descale ON (O), Led CalcClean ON (O), Led Rinsing ON (O)
e) Level 5: Led Espresso ON (G), Led Descale ON (O), Led CalcClean ON (O), Led Rinsing ON
(O), Led Coffee ON (G).
Legend:
(O) = Orange
(G) = Green
(R) = Red
TEST MODE Level0
Pressing button ON/OFF
TEST MODE Level1
Pressing button ON/OFF
TEST MODE Level2
Pressing button ON/OFF
TEST MODE Level3
Pressing button ON/OFF
Pressing button ON/OFF
TEST MODE Level4
Pressing button ON/OFF
TEST MODE Level5
At the start up all loads are turned off. The software allow to have only one load active at the same
time.
Level 0 (Start Test mode)
Start condition: NO BU, NO drag drawer, Door open, No
Water in tank, Coffee Beans cover open
LED INDICATION
Led Espresso
Led Coffee
Blink Alternately
Press BUTTON ON/OFF to move to the next screen
Page 39 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Level 1 (Key)
Start condition: NO BU, NO drag drawer,
Door open, No Water in tank, Coffee Beans
cover open
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Led
Descale
Led
Rinsing
OFF
OFF
OFF
OFF
OFF
OFF
Press Espresso Button
Action by user
LED INDICATION
Switch on Red Leds NoWater & GenAlarm
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Led
Descale
Led
Rinsing
OFF
ON
OFF
ON
OFF
OFF
ERROR: Led NoWater remains off, check
the interface board and flat cable (JP21)
OFF
ON
ERROR: Led Dreg remains off, check the
interface board and flat cable (JP21)
ON
OFF
ERROR: Led NoWater & Dreg remain off,
check the interface board and flat cable
(JP21)
OFF
OFF
Press CalcCLean Button
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Led
Descale
Led
Rinsing
OFF
OFF
OFF
OFF
ON
ON
ERROR: Led Descale remains off, check the
interface board and flat cable (JP21)
OFF
ON
ERROR: Led Rinsing remains off, check the interface board and flat cable (JP21)
ON
OFF
ERROR: Led Descale & Rinsing remain off,
check the interface board and flat cable
(JP21)
OFF
OFF
Switch on Orange Leds Descale & Rinsing
Press Coffee Button
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Led
Descale
Led
Rinsing
Switch on Red Leds Dreg & NoBeans
ON
OFF
ON
OFF
OFF
OFF
ERROR: Led NoBeans remains off, check
the interface board and flat cable (JP21)
OFF
ON
ERROR:Led GenAlarm remains off, check
the interface board and flat cable (JP21)
ON
OFF
ERROR:Led NoBeans & GenAlarm remain
off, check the interface board and flat cable
(JP21)
OFF
OFF
Page 40 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Press Steam Button
Action by user
LED INDICATION
Led Steam Button
Led HotWater Button
Switch on Steam Button LED
ON
OFF
ERROR: Led Steam Button remains off,
check the interface board and flat cable
(JP21)
OFF
OFF
Press Steam Button
Action by user
LED INDICATION
Led Steam Button
Led HotWater Button
Switch on Hot Water Button LED
OFF
ON
ERROR: Led Hot Water Button remains off,
check the interface board and flat cable
(JP21)
OFF
OFF
Finish condition: NO BU, NO drag drawer,
Door open, No Water in tank, Coffee Beans
cover open
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Led
Descale
Led
Rinsing
OFF
OFF
OFF
OFF
OFF
OFF
Press BUTTON ON/OFF to move to the next screen
Level 2 (Input)
Start condition: NO BU, NO drag drawer, Door open, No
Water in tank, Coffee Beans cover open
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
ON
ON
ON
ON
Insert a full Water Tank
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Switch off Red Leds NoWater
NA
OFF
NA
NA
ERROR: Led NoWater remains on, check the capacitive
sensor (fixing) and the wiring (JP23)
NA
ON
NA
NA
Insert the Brew Unit
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Switch off Red Leds GenAlarm
NA
NA
OFF
NA
ERROR: Led GenAlarm remains on, check the BU presence Microswitch and the wiring (JP16).
NA
NA
ON
NA
Page 41 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Close the door and Dreg Drawer
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Switch off Red Led Dreg
NA
NA
NA
OFF
ERROR: Led Dreg remains on, check the Microswitch for
the door and the wiring (JP14). NOTE: without the Dreg
Drawer correctly inserted the DOOR indication cannot
change!
NA
NA
NA
ON
Close coffee beans cover
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Switch off Red Leds GenAlarm
OFF
NA
NA
NA
ERROR: Led GenAlarm remains on, check
the BU presence Microswitch and the wiring
(JP16).
ON
NA
NA
NA
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
OFF
OFF
OFF
Finish condition: With BU, NO drag drawer inserted,
Door closed, Water in tank, Coffee Beans cover closed
LED INDICATION
Press BUTTON ON/OFF to move to the next screen
Level 3 (Brewing unit)
Start condition: NO BU, Drag drawer inserted, door
closed, No Water sensor, Coffee beans cover open
If the DREGDRAWER is not inserted or the DOOR is
not closed the BU test cannot be performed. If these 2
inputs are not in the right position, Led Dreg will be RED
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
OFF
OFF
OFF
NA
NA
NA
ON
Press the Espresso button to move BU to work
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
When the BU reaches the work position the Led NoBeans
is switched on
ON
NA
NA
NA
ERROR: Led NoBeans remains off, Check the work microswitch (broken?), the BU motor (blocked?) and the
wiring.
NA
NA
NA
NA
ERROR: led GenAlarm Switch ON; the absorbed current
is much more 300mA (with BU) or 200mA (without BU)
check the BU and the motor
NA
NA
ON
NA
Page 42 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Press the Coffee button to move BU to home
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
When the BU reaches the work position the
Led NoBeans is switched on
ON
NA
NA
NA
ERROR: Led NoBeans remains off, Check the work microswitch (broken?), the BU motor (blocked?) and the
wiring.
NA
NA
NA
NA
ERROR: led GenAlarm Switch ON; the absorbed current
is much more 300mA (with BU) or 200mA (without BU)
check the BU and the motor
NA
NA
ON
NA
Finish condition: No BU, Drag Drawer inserted, door
closed, No Water sensor, Coffee beans cover open
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led Dreg
OFF
OFF
OFF
OFF
Press BUTTON ON/OFF to move to the next screen
Level 4 (Pump)
Start condition: No BU, Drag drawer, door Closed and
No Water sensor, Coffee beans cover closed
If the DREGDRAWER is not inserted or the DOOR is not
closed the BU cannot be moved in work position and test
cannot be performed.
If these 2 inputs are not in the right position, Led Dreg
will be RED
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
OFF
OFF
OFF
NA
NA
NA
ON
Press the Espresso Button
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
Turn On Ev1
ON
NA
NA
NA
ERROR: If Ev remain closed check EV
(broken?), and the wiring
ON
NA
NA
NA
Press the Lungo button to switch on the Pump
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
The water goes out from the dispensing spout,the NoWater LED blink every Flowmeter pulse
NA
BLINK
NA
NA
ERROR: the NoWater LED does’t flashing
and after 5sec this LED Switch ON; check:
1) EV open?,
2) pump,
3) the flowmeter,
4) the wiring from the flowmeter to the
CPU/POWER board (JP5)
5) the wiring from the pump to the
CPU/POWER board (JP24)
NA
ON
ON
NA
Page 43 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
Finish condition: No BU, Drag drawer, door Closed
and No Water sensor, Coffee beans cover closed
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led Dreg
OFF
OFF
OFF
OFF
Press BUTTON ON/OFF to move to the next screen
Level 5 (Grinder-Heater)
Start condition: NO BU, NO drag drawer,
door open and No Water sensor
LED INDICATION
If the Coffee Beans cover is opened the grinder is disabled and test cannot be performed. If this input are not
in the right position, Led NoBeans & Led Dreg will be
RED
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
OFF
OFF
OFF
OFF
ON
NA
NA
ON
Check the Temperature
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
The red led General Alarm remains OFF
NA
NA
OFF
NA
ERROR: The temperature sensor is shorted or opened,
the led GenAlarm switch ON; check the wiring from the
heater to the CPU/POWER board (JP13).
NA
NA
ON
NA
Press the Espresso button to switch on the Heater
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
The user checkers that the absorbed current is OK
NA
NA
OFF
NA
ERROR: the absorbed current is KO; check the wiring
from the heater to the CPU/POWER board (JP17-3) and
the other wiring, or thermostats.
NA
NA
OFF
NA
ERROR: If temperature is over 100°C, the NoWater LED
turn ON. This is a ALERT message to avoid heating the
HEATER element over dangerous temperature; and
Heater test cannot be performed.
ON
Press the Coffee button to switch on the Grinder
Action by user
LED INDICATION
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led
Dreg
The grinder rotates and Led NoBeans Blink every grinder
pulses.
BLINK
NA
OFF
NA
ERROR: the led NoBeans remains OFF and after the led
NoBeans switch ON; check the hall sensor board in the
Grinder, the Grinder, the wiring from the hall sensor
board to the CPU/POWER board (JP2) and the wiring from
the Grinder to the CPU/POWER board (JP8)
ON
NA
OFF
NA
Led
NoBeans
Led
NoWater
Led
GenAlarm
Led Dreg
OFF
OFF
OFF
OFF
Finish condition: With BU, Drag Drawer, door closed
LED INDICATION
Page 44 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
05 TROUBLESHOOTING
5.6.2. SteamOut
To enter in SteamOut
The machine enters SteamOut mode by holding pressed together the COFFEE button and the
CALC_CLEAN button while switching on the machine.
Once entered shows Led Descale and Led Rinsing flashing in series.
If Door is opened or drag drawer is removed LED WASTE FULL will be switched on.
At the end of procedure Brewing Unit will be moved to rest position and LED ESPRESSO and LED
COFFEE turns on.
When the Steam-Out is complete the following parameters are reset to their default values:
•
•
•
•
•
•
•
•
•
•
•
Length Espresso product
Length Coffee product
StandBy Time
Count Coffee
The request for Priming the Circuit at the first switch on is set.
Aroma
Aroma Impulses
Filter Presence
Filter Pulses
Dynamic threshold
History of grindings for Beans Presence detection
Page 45 / 46
Downloaded from www.Manualslib.com manuals search engine
MINUTO
5.7.
05 TROUBLESHOOTING
Error codes
ERROR
CODES
01
03
04
05
10
11
14
15
19
22
DESCRIPTION
The coffee grinder is blocked (grinder blades jammed or sensor not
reading properly)
The brewing unit is blocked in work position (microswitch not released
in up position after 3", torque error trying to move down, descent time
out exceeded)
The brewing unit is blocked in home position (microswitch not released
in down position after 3", torque error trying to move up, ascent time
out exceeded)
Water circuit / flow meter problems (water circuit blocked or no flow
meter signal)
Boiler temperature sensor short circuited
Boiler temperature sensor open circuit
The boiler temperature has exceeded the maximum allowed value
(165°c)
The boiler temperature has not increased by x°C in y sec (boiler power
supply disconnected, incorrect boiler fitted must be a 1300W boiler, partial power supply to boiler, cut out thermostat tripped)
Mains voltage trouble
interface missing or unknown
Page 46 / 46
Downloaded from www.Manualslib.com manuals search engine
CHAPTER 6
STANDARD CHECKS
MINUTO
Downloaded from www.Manualslib.com manuals search engine
MINUTO
6.1.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
06 STANDARD CHECKS
Repair schedule
Action
Visual inspection (transport damage)
Machine data check (rating plate)
Operational check / problem analysis
Opening machine
Visual inspection
Operational tests
Repairing the faults encountered
Checking any modifications (view Symptom Cure, new software, etc.)
Service activities in accordance with the operating schedule
Internal cleaning
Operational test while the appliance is open
Assembly
Final inspection test
Draining the circuit (in winter)
External cleaning
Lubricating the brewing unit with suitable grease
Insulation test HG 701 (dielectric)
Documentation
6.2.
Service schedule
S Replacement
ES Visual inspection
D Descaling
Component
Water filter
Water tank lip seal
Boiler pin O-ring
Brewing unit
Hoses, attachments and Oetiker clamps
Pump
Gear motor
Coffee grinder
Water circuit
Hot water/steam valve
P
TR
R
Cleaning
Noise test
Adjustment
Action
P/S
S
S
ES/P
ES
ES/TR
ES/TR
P/R
D
ES/S
Support/tool
Grease solvent / Grease
Vacuum cleaner / brush
Saeco descaler
Page 01 / 02
Downloaded from www.Manualslib.com manuals search engine
MINUTO
6.3.
06 STANDARD CHECKS
Final test
Test
Espresso
Coffee
Procedure
2-3 Espressos for
adjustment purposes
2-3 Coffees for
adjustment purposes
Support/
tool
Measuring
scoop
Measuring
scoop
Noise
Amount of
cream
Grinding level
Hot water
Steam
Dreg drawer
missing
indication
Low bean level
indication
Tolerance
Same amount
15%
Same amount
15%
Standard
The cream should
come together
again to form a
complete layer
Blow into the cup until
the cream separates
Cream colour
Temperature
Standard
Hazel brown
Reading taken while
dispensing
Check the grain size of
the ground coffee
Dispense water
Dispense steam
Thermometer
84 ˚C
Remove the dreg drawer
Dreg drawer
missing indication
Start brewing a coffee
while the coffee bean
hopper is empty
Low bean level
indication
± 4 ˚C
Page 02 / 02
Downloaded from www.Manualslib.com manuals search engine
CHAPTER 7
DISASSEMBLY
MINUTO
Downloaded from www.Manualslib.com manuals search engine
MINUTO
7.1.
07 DISASSEMBLY
Outer Shell
Minuto Cappuccino
Remove the water tank, coffee container cover,
drip tray, dreg drawer, brewing unit.
Coffee dispenser Minuto
Remove the dispenser
cover
Unscrew the screws shown and remove
the dispenser
Unscrew the screws and
proceed as illustrated in
the following pages.
exploded view of the
coffee dispenser
Page 01 / 09
Downloaded from www.Manualslib.com manuals search engine
MINUTO
07 DISASSEMBLY
Coffee dispenser Minuto for USA
Remove the cover
Unscrew the screw shown and remove
the inserts with a screwdriver
Remove the lower dispenser
and unscrew the screws
shown for remove the lever
Unscrew the screws and proceed as
illustrated below.
exploded view of the
coffee dispenser
Remove the steam pipe cover as picture and unscrew the screw shown.
7.2.
Unscrew the screws shown, raise the
top cover and remove the electrical
and water circuit connections.
Coffee grinder
Raise the coffee grinder and remove the connections.
When reassembling the coffee
grinder, make sure the spring is
repositioned correctly (see photo).
Page 02 / 09
Downloaded from www.Manualslib.com manuals search engine
MINUTO
7.3.
07 DISASSEMBLY
Grinder blades
A
B
To extract the top support of the appliance, press
on the grinding adjustment spindle (A) and turn the
support anticlockwise until it unhooks.
Turn the grinder blades anticlockwise out of the support.
Turn the grinder blades clockwise out of the support. The
bayonet connections can be accessed from the rear.
For a standard adjustment, both markings must be
aligned.
Page 03 / 09
Downloaded from www.Manualslib.com manuals search engine
MINUTO
7.4.
07 DISASSEMBLY
Coffee grinder adjustment
+
-
The grinding adjustment can be set by the user (only with the coffee grinder in operation) by pressing and turning (only by one click at
a time) the insert inside the coffee bean hopper with the aid of the
wrench supplied.
Adjustment by a service center
C
-
+
A
B
To adjust grinding further, the engineer can work directly on the coffee grinder by pressing and turning
the ring nut (C) shown. (clockwise + to increase the particle size of the coffee and anticlockwise - to
decrease it).
If there are any remains of coffee powder between the two grinding blades it is recommended to
tighten by max. two marks at a time.
Lastly, move the arrow (A) on the adjustment knob to the center of the adjustment dots on the
cover (B).
Page 04 / 09
Downloaded from www.Manualslib.com manuals search engine
MINUTO
07 DISASSEMBLY
7.5.1 Two-way solenoid valve
Remove the board support
assembly and disconnect
the electric connection
Loosen the screws holding
the solenoid valve to the
upper plate
Disconnect all electrical and water
circuit connections
Two-way solenoid valve in Minuto Cappuccino
Disconnect all electrical and water
circuit connections
7.5.2 Carafe connection and hot water dispenser in Minuto Cappuccino
Slide out the fork
as illustrated
7.6.
Loosen the screws holding
the carafe connection
When reassembling the assembly to be
careful to correctly position the spring.
Pin boiler
A
Loosen the screws as illustrated and
remove the boiler pin (A).
Page 05 / 09
Downloaded from www.Manualslib.com manuals search engine
MINUTO
7.7.
07 DISASSEMBLY
Gear motor
Loosen the screws as illustrated and
remove the gear motor cover.
The following are located inside the compartment protected
by the casing:
- Electric motor (A) with gears (B) and (C) for transmission
and timing of the dispenser.
- Brewing unit present microswitch (E).
- Microswitch (D) detecting brewing unit home and work positions.
- Remove the gear (C) that meshes with the motor transmission shaft.
- Remove the large gear (B).
- Remove the motor (A), complete with transmission shaft.
E
D
A
B
C
Replace the gear (B), making sure that the imprint of
the arrow is aligned with the opening containing the
pin (P).
B
P
H
L
7.8.
When replacing the motor and the transmission
shaft, make sure the guide runners (L) are in the
right position.
Grease the shaft thoroughly and evenly.
Central plate
unscrew the screws shown
Lift up the center plate
Page 06 / 09
Downloaded from www.Manualslib.com manuals search engine
MINUTO
07 DISASSEMBLY
7.9.
Pump
A
D
Unhook the pump
from the supports.
B
B
B
D
C
A A
Disconnect the water circuit connections (A) and
electrical connections (B), loosen the safety valve (C) and
slide the pump off the brackets (D).
7.10. Flow-meter
Lift the flow meter out of the casing assembly and remove the electrical
and water circuit connections.
7.11. Boiler
Unscrew the screw shown at
unthread the support boiler
Unscrew the screw shown and remove the
electrical and water circuit connections.
Page 07 / 09
Downloaded from www.Manualslib.com manuals search engine
MINUTO
07 DISASSEMBLY
7.12. CPU board
Loosen the screws slide the
card off the support and
disconnect the electrical
connections.
7.13. Programming access for SSC (Saeco Service Center)
Loosen the screw for
remove the cover.
7.14. KYB interface and display
Disconnect the electrical connections.
Press to right and left and lift the
assembly KYB
Loosen the screws for
remove the cover.
Disconnect the electrical
connections.
Page 08 / 09
Downloaded from www.Manualslib.com manuals search engine
MINUTO
07 DISASSEMBLY
7.15. Fitting and removing Oetiker clamps
1) Boiler connection.
2) Other connections.
Use a suitable pair of pliers to remove the
clamp (as illustrated).
Tighten the clamp as illustrated.
Page 09 / 09
Downloaded from www.Manualslib.com manuals search engine
CHAPTER 8
NOTES
MINUTO
Downloaded from www.Manualslib.com manuals search engine
MINUTO
08 NOTES
Page 01 / 01
Downloaded from www.Manualslib.com manuals search engine
CHAPTER 9
WATER CIRCUIT DIAGRAM
MINUTO
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Safety valve
Pump
Two - Way
solenoid valve
Water discharge
Carafe
connection
Brewing Unit
Water discharge
Flowmeter
Boiler
3D view to indicate the
mounting of the exhaust pipe
to the tank compartment
Two - Way
solenoid
valve
MINUTO
09 WATER CIRCUIT DIAGRAM
Minuto Cappuccino
Page
01 / 03
Downloaded from www.Manualslib.com manuals search engine
Safety valve
Valvola di sicurezza
Pump
Pompa
Water tank
Serbatoio
acqua
Flow meter
Turbina
Water drain
Scarico acqua
Boiler pin
Perno caldaia
steam pipe
Boiler
Caldaia
Assy Solenoid valve
Assieme Elettrovalvole
MINUTO
09 WATER CIRCUIT DIAGRAM
Minuto Focus and Class
Page 02 / 03
MINUTO
09 WATER CIRCUIT DIAGRAM
Safety valve
Water drain
Boiler pin
Pump
Water tank
Flow meter
Exit closed
Boiler
Minuto Pure
Page
Downloaded from www.Manualslib.com manuals search engine
03/ 03
CHAPTER 10
ELECTRICAL DIAGRAM
MINUTO
Downloaded from www.Manualslib.com manuals search engine
MINUTO
10 WIRING DIAGRAM
Minuto Cappuccino Focus and Class
Page 01 / 02
Downloaded from www.Manualslib.com manuals search engine
MINUTO
10 WIRING DIAGRAM
Minuto Pure
Page 02 / 02
Downloaded from www.Manualslib.com manuals search engine
Download PDF
Similar pages