Slush & Smoothie Machine
User's Manual
ST 12 x 2 , ST 12 x 3 , MI 7.5 x 2
The product has been designed for indoor use only.
So do not use it outdoors.
Before use of the product, be sure to become familiar with this manual.
Keep the manual in a convenient place for quick and easy reference.
This manual contains the product warranty card.
The product design is subject to change for performance enhancement
without prior notice.
Contents
1.Names of Parts
3~
2.Overview
3.Safety Signs, Symbols, and Labels
4.Safety Instructions
5.Installation Requirements
6.Safety Cautions for Operation
7.Operation Procedure
1~1
7.1 Controllers
7.2 Operations
7.3 Cleaning and sterilization procedure
7.3.1 Disassembling the product
7.3.2 Cleaning the product
7.3.3 Sterilizing the product
7.3.4 Assembling the product
7.3.5 Sterilizing the site
8.Daily Check
8.1 Repairing the product (by qualified engineer only)
9.Specifications
10.Circuit Diagram
11.Before Calling Service
12.Part List
2~2
2
2~6
13.When Receiving Servic
7
Product Warranty Card
8
2
- Keep the manual in a convenient place for quick and easy reference. -
1. Names of Parts
MI7.5X2
MODEL :: SSM-52
3
MODEL :: SSM-280
ST12X2
4
MODEL :: SSM-420
ST12X3
5
2.Overview
To become familiar with this product, be sure to read this manual carefully.
This product requires cleaning and maintenance activities as in other machines.
Any disassembly or cleaning mistakes may cause a product failure.
It is highly recommended for the person in charge to have immersion training for activities.
3.Safety Signs, Symbols, and Labels
The warnings and safety instructions in this manual do not cover all possible conditions and
situations.
While operating, moving or cleaning this product, manipulate it carefully based on common
sense. If a bad and non-understandable symptom happens, feel free to contact the
purchased site or service agency.
This is the safety warning symbol. It is used to warn users of any potential
risk of injuries. To evade from the risk of injury or death, comply with the
safety requirements for the symbol.
Danger
Warning
Caution
Caution
6
Important
If you neglect this symbol and wrongly use the product, it may cause
death or serious injury.
If you neglect this symbol and wrongly use the product, it may cause a
potential risk of death or serious injury.
If you neglect this symbol and wrongly use the product, it may cause a
potential risk of injury.
If you neglect this with no caution symbol and wrongly use the product, it
may cause a potential risk of property damage.
You must check the electrical rating on the nameplate of the product. The nameplate is
attached on the rear of the product. The nameplate specification has priority over
information in this manual. The electric circuit diagram of the product is attached inside of
the panel. In addition, the product specification is subject to change without prior notice.
4.Safety Instructions
Be sure to use the grounded
consent.
Do not pull off the power
plug.
It may cause a failure or
electric shock.
It may cause a failure or
electric shock.
Do not move the product
by pulling the power plug.
Do not contact the power
plug with wet hands.
It may cause a failure or electric
shock.
It may cause an electric shock or fire.
Do not forcibly bend the power
plug or place any heavy material
on it.
When the power plug is
removed from the outlet, insert
it after 5 minutes.
It may cause an electric shock or fire.
Otherwise, It may cause a
product failure.
Remove water or dust from
the power plug and insert
it fully into the outlet.
When repairing the product or
replacing the parts, remove the
power plug from the outlet.
It may cause a fire or electric shock.
It may cause an electric shock or fire.
When not using the product for
a long time, remove the power
plug from the outlet.
Do not connect multiple
products to
a single outlet.
It may cause an electric shock or fire.
It may cause a fire.
When the power plug is
damaged, do not replace it
arbitrarily and contact the
service agency.
Do not connect the power
plug arbitrarily or nor modify
it.
It may cause an electric shock or fire.
It may cause an electric shock or fire.
Caution!
Use this product as described in the user manual.
- If you do not follow the instructions, it may cause an electric shock or property loss.
- When transferring the product to another person, transfer the user manual also.
- Before supplying power, check whether the voltage is the same as the one
of the nameplate.
According to applicable electric code regulations and machine specifications, ground
the product and connect to the single phase power. If the product has no plug, install
the grounded plug to meet at least 15 A 250 V (220 to 230 V, 50 to 60 Hz). For directly
connecting the product to the main power, connect the power cord to the 2 pole circuit
breaker. Never use the extension cord with no grounding.
7
5. Installation Requirements
Do not install the product
near the heat generating
source.
Do not install the product
in a humid, dusty, or water
(e.g. rain) splashing place.
It may cause a fire.
It may cause an electric shock or fire.
Do not install the product near
combustible gases
or inflammable materials.
When moving the product,
be careful not
to slip and fall.
It may cause a fire.
It may cause an injury or
product damage.
Do not forcibly apply force or
shock to the product.
This product is for indoor use
only. So install the product
inside the house.
It may cause damage to the product.
Keep at least 30 cm distance
for the side and rear of the
product.
Do not install the product
on a weak or uneven floor.
Adjust the vertical balance of
the product not to shake and
then adjust the horizontal
balance.
Check any damage of the
product.
It may cause vibration and noise.
If found, contact the delivery agency
to request claims on it.
Firmly fix the product.
The drain hose is located
on the top of the drain box.
8
Caution!
This product is for indoor use only. So do not install the product outdoors. Inevitably, when
the product is installed outside, prepare a shade to block direct sunlight, rain, wind, and dust
for sanitary control and optimal performance. Install the product in the place where you can
easily manage it to prevent robbery and loss by dangerous play.
6.Safety Cautions for Operation
Keep away any flammable
materials.
It may cause a fire or explosion
due to electric spark.
If the product makes heavy noise or
does not operate properly, remove the
power plug and contact the service
agency.
It may cause an electric shock or fire.
Do not use any flammable
spray such as pesticide
and air freshener.
It may cause a fire.
Operate the product in a nonhumid place.
In a humid place, the product
easily gets rusty or has an
electric leak.
If the floor gets humid, wipe it with
soft cloth.
Use the product in a well
vented place.
Gas or smoke can discolor the
surface of the product.
Be cautioned of gases!
When gas leak happens, do not
touch the product.
If you open the door or remove
the power plug, it may cause an
explosion due to spark.
Do not touch the product.
Fully close the gas burner.
Open the window for ventilation.
Do not forcibly apply
force to the slush supply
lever nor hang on it.
Check the supplied power.
When the PVC coating of the power
cable is stripped off or the shunt
socket is used, it may cause a fire.
Do not use the product in the
ambient temperature of
5 or below for a long time.
It may cause a product failure.
Do not spray water and wipe
the product with a clean wet
towel.
If you directly spray water,
it may cause an electric leak
or product failure.
For food sanitation, clean and
sterilize the product every day
Before cleaning, remove the
power plug from the outlet.
Do not insert your finger or
other materials into the panel
rubber or the slush supply.
It may cause damage to the
product.
Do not operate the product
while all panels are not well
fastened enough.
When the product is not
separated from the power
supply, do not clean the
product nor remove the
canister, spiral or panel.
While operating the product, do not hold the product using the canister or evaporator drum. The
manufacturer assumes no responsibility for any damage caused by careless handling.
Caution
9
7.Operation Procedure
# Clean and sterilize the product according to the instructions in this manual.
See7.3 Cleaning and sterilization procedure.
$ Fill up the liquid material up to the level specified on the canister. Do not overfill it.
The optimal quantity (in liter or gallon) is written on the surface of canister.
% When diluting the liquid material, fill water into the canister first and pour the liquid material for
dilution. In case of natural materials, do not make the slush supply get clogged up.
& For optimal performance, use the base that has been designed for use in the slush machine.
The base contains the sugar level of 34-(Baume) that is corresponded with 64-(Brix).
In case of soft drinks, dilute the base 1 to 5 or 5.5 using water.
In some cases, for both granita and soft drink recipes, you must follow the directions
from the syrup manufacturer. If natural juices (e.g. lemon, orange) are used together
with non-sugar material (e.g. coffee), 150 to 200 g of sugar per liter must be dissolved.
Caution!
- Food or edible materials must be used in the product.
- When using the granita (smoothie, slush) mix, be sure to have at least
13% of sugar level (Brix).
' In case of using the liquid material, keep the following instructions:
- After mixing the one liter of liquid material (juice pack with 50% of sugar level) with
four liters of water, fill the mixed liquid in the material box.
- Note that when any machine failure occurs due to use of liquid material or powder,
the manufacturer assumes no responsibility.
In case of soft drinks (1.5 liters of fruit juices bottled in PET plastic) that can be easily
purchased, fill three of bottles (4.5 liters) in the material box. (in case of 13 to 15% of sugar level)
(e.g. orange soda, fanta, etc.-soft drinks including 10% of fruit juices)
Do not use low calorie drinks.
Do not use fruit nectar that includes fruit particles.
( Set the control switch as described in7.1 Controllers.
) When the thickness of granita (smoothie, slush) reaches the optimal value, freezing
automatically stops. So always keep the product turned on. The spiral keeps rotating.
* In case of using other materials such as sweet rice drink, contact the service agency or
distributor for inquiry.
10
Caution!
This product must not be used by the persons with poor mental or physical condition, or
the persons without experience or knowledge (including children). If those persons use
the product, a responsible person must manage the use of the product. Guide children
not to play with the product.
7.1 Controllers
The product is equipped with the power switch. Canisters operate by each individual
switch. You can use both soft (refrigeration) drinks and granita (smoothie, slush).
In the refrigeration mode, the temperature of the drink is controlled by the thermostat.
In the freezing mode, the viscosity of the mixed material is controlled by the bolt on the
rear of the product.
(For more information about the temperature and viscosity settings, see7.2 Operations.
)
All switches are located on the right panel. (See Figure 2.)
The switches in Figure 3 function as follows:
0 Power Switch
!POSITION
POSITION
: All functions and switches are activated.
The fan motor operates.
: All functions are deactivated.
1 Supply Switch
!POSITION
POSITION
: The spiral motor operates and theCswitch is activated.
: The fan motor is turned off.
2 Freezing/Refrigeration Switch
!POSITION
POSITION
POSITION
: The product operates in granita (smoothie, slush) mode.
: The freezing and refrigeration functions are deactivated.
: The product operates in soft (refrigeration) drink mode.
To operate the product:
# Place the power switch to I.
$ Place the supply switch to I.
% Set the freezing/refrigeration switch as follows:
- Place the switch to I for making granita (smoothie, slush).
- Place the switch to II for providing soft (refrigeration) drink.
To operate the lighting: (excluding SSM-52)
If you turn on the lighting, the bulb inside the cap of the material box lights.
Otherwise, check whether the spring cord on the top of the cap is properly inserted.
If the life of the lighting is expired, remove the bottom panel of the cap and replace
the lamp (12 V & 21 W). (If the life of the lamp is expired, replace it with the
provided part.)
11
7.2 Operations
# Adjusting the granita viscosity: The optimal granita viscosity is set by the manufacturer.
To change the viscosity, rotate the control bolt on the rear of the product as follows:
(See Figure 4.)
- To make thicker granita, rotate the control bolt to the right (clockwise).
- To make watery granita, rotate the control bolt to the left (counter-clockwise).
$ Adjusting the drink temperature: The optimal temperature is set by the manufacturer.
For setting it again, rotate the temperature controller inside the rear panel as follows:
- To lower the temperature, rotate it to the right (clockwise).
- To increase the temperature, rotate it to the left (counter-clockwise).
Important
12
The drink temperature is controlled by the thermostat, only when the
freezing/refrigeration switch is located inII(soft drink mode).
% The granita forming time is affected by various factors such as ambient temperature,
initial material temperature, sugar level (Brix level) and viscosity setting. Though the
conditions are the same, the forming time may vary depending on the canister.
& To reduce the granita forming time and increase the productivity, it is
recommended to use the refrigerated materials.
' To reduce the granita forming time and increase the productivity, when the
remaining material level drops below half, fill the material in the canister.
( To preserve the material safely, be sure to operate the product in soft drink mode.
To leave the material in the canister during all night without refrigeration, operate
the product for at least one hour while the freezing/refrigeration switch is in II
before switching off the product. It can prevent forming lumps of ice that can give
damage to the spiral and motor.
) Before operating the product again, check whether lumps of ice have been formed.
If any lumps of ice are in the canister, remove them before switching on the
product. If you operate the product in refrigeration mode during all night, it can
prevent accumulation of the condensed ice
* When the granita is in the canister, do not turn off the slush supply switch.
It is because hard ice can form if the spiral does not rotate. If you turn on the slush
supply switch at this time, the spiral and motor can have damage.
Therefore, turn on the slush supply switch after melting the frozen granita.
+ The product has the shaft so that the gear motor (outside the canister) can drive
the spiral (inside the canister).
, The product must be located in a well vented place.
If the temperature of the product is hot, check whether there is any heat generating
source, or air flow through the panel with a hole is blocked by the wall or box.
Keep at least 30 cm distance between the product and other materials.
7.3 Cleaning and sterilization procedure
# To maintain optimal taste and guarantee the maximum product performance,
periodically perform cleaning and sterilization. Only the procedural instructions are
provided here.
$ Before disassembly and cleaning, be sure to remove all materials from the product.
For this, follow the procedure below.
- Place the power switch to I.
- Place the freezing/refrigeration switch to O.
- Place the containers beneath each slush supply and extract all materials from
the canisters.
- Place all control switches to O.
7.3.1 Disassembling the product
Before disassembly and cleaning, remove the power plug to block power supply.
Warning
# Remove the cover of the canister.
13
$ Lift the front of the canister to unlock the latch (Figure 5)
and pull out the canister to the front. (See Figure 6)
% Remove the spiral by pulling out (Figure 7)
and remove the packing cushion. (See Figure 8)
& Remove the rubber cushion.
(See Figure 9).
' Remove the slush supply
as shown in the figure.
(See Figure 10).
( Lift the drip tray and pull it out, and empty the remaining water.
14
7.3.2 Cleaning the product
Never clean the parts in the dish washer.
Warning
# Prepare the solution mixed with five liters of warm water and kitchen detergent.
Do not use a strong detergent.
$ After inserting the mixed solution that does not harm the food, turn on the slush
supply switch to extract the solution.
% Frequently empty the remaining materials in the material box and drain box and clean them.
Turn off the freezing switch.
Caution
Warning
It may cause spiral freezing and motor failure.
In order not to give damage to the product, use the washing detergent for cleaning plastic
parts.
& Use the proper brushes to clean the disassembled parts using the washing detergent.
Caution
When cleaning the product, be careful not to insert water in the electrically running parts. It
may cause an electric shock or product failure.
' Do not spill any liquid on the cover of the motor that is on the rear of the product.
( Likewise, use a soft bristle brush to clean the evaporators cylinder.
) Use clean cold water for cleaning the parts.
* Be sure to clean the filter.
As shown in the figure, on a monthly basis, open the cover of the condenser,
clean the filter with lukewarm water (about 25) or
neutral detergent solution, dry it, and attach it back
to its original position. If ventilation is not made due
to accumulated dust, slush is not smoothly formed
and machine failure may follow. When the troubles
are caused by careless use or user faults such as
no filter cleaning, you can get a charged service.
. Cleaning the condenser /
1. Separate the SIDE PANEL L
2. Use a vacuum cleaner or hand cleaner to remove dust
from the condenser
15
7.3.3 Sterilizing the product
Sterilization is performed before operating the product. After sterilization, do not leave
the product for a long time.
# Wash your hands with an anti-bacterial soap.
$ According to the food safety regulations and manufacturer specifications,
prepare five liters of warm (45 to 60) sterilization solution (dilute a spoon of
chloride condense liquefaction or sodium chlorate with two liters of water (100 ppm)).
% Soak the parts in the sterilization solution for five minutes.
& Place the sterilized parts on a clean and dry place for drying them.
' Wipe all the surfaces of the product.
( Do not spill any liquid on the cover of the motor that is on the rear of the product.
7.3.4 Assembling the product
# Attach the drip tray to its original position.
$ Paint two piston rings and spiral with the grease provided
by the manufacturer or the approved edible grease.
(See A and B in Figure 11.)
% Attach the slush supply in the reverse order of disassembly.
(See Figure 10.)
& Attach the rubber cushion.
Caution : Be sure for the wide border of the gasket to face
the wall.
(See Figure 12).
' Attach the packing cushion and spiral.
(See Figure 13.)
16
Caution Before attaching the packing cushion, paint the
inner part with edible grease.
After assembly, paint the outer area
with edible grease.
')0/3- 97./43
( Push the canister fully into the canister to fix in the
packing cushion and fixing latch.
(See Figure 14).
) Use fresh material to remove the remaining sterilization solution on the surface
of the canister.
Afterwards, do not rinse the product.
Caution
To reuse the product after a long time, paint the packing cushion with edible grease as in
'. Otherwise, noise may be heard from the product.
For correction, you have to get a charged service.
7.3.5 Sterilizing the site
The site sterilization can be performed additionally after parts sterilization but it cannot
replace the parts sterilization.
# According to the food safety regulations and manufacturer specification, prepare
five liters of warm (45 to 60) sterilization solution (remaining chloride 100 ppm).
$ Fill the solution in the canister.
% Use the proper brushes to wipe the surfaces projected above the solution level
and the lower area of the canister cover with the solution.
& Attach the canister cover and operate the product for mixing the solution for about
two minutes. Drain the solution from the canister.
' Use fresh material to remove the remaining sterilization solution on the surface of
the canister. Afterwards, do not rinse the product.
17
8. Daily Check
Warning
If the power cord is damaged, only the qualified person must replace it to prevent electric
shock.
# Daily check: It checks any possible leak through the packing or gasket.
If leak happens through the packing or gasket even though properly assembled,
check the use of improper grease or parts wear. If necessary, replace parts.
- Before disassembly and cleaning, remove the power plug to block
power supply.
Caution
- The pin of the condenser is very sharp. Be careful while cleaning it.
8.1 Repairing the product (by qualified engineer only)
# Yearly repair: Remove the panel and clean the inner parts including the base,
side panels, and condenser.
$ To prevent damage to the product, paint all plastic parts with the grease provided
by the manufacturer or the grease proper for cleaning the plastic parts.
18
9. Specifications
%NCUUKſECVKQP
&GUETKRVKQP
2TQFWEVPCOG
5NWUJ5OQQVJKG/CEJKPG
/QFGNPCOG
SIZE (WxDxH)
BODY
'NGEVTKE
(GCVWTG
(TGG\KPI
ST12x3
MI7.5x2
400×480×895
600×480×895
417×386×705
Case
5VCKPNGUU5VGGN
+PUWNCVKQP
7TGVJCPG(QCO
220V
2QYGT
%QPUWORVKQP
1020
1350
500
%WTTGPV
%QPUWORVKQP
5.0A
6.4A
3.5A
)GCTGF/QVQT
2EA
3EA
2EA
(CP/QVQT
16W
16W~34W
10W
%QORTGUUQT
(WNN[%NQUGF
%QPFGPUGT
2KPVWDGV[RG
'XCRQTCVQT
6WDGNCWPEJGF&TWO6[RG
%QQNKPI6[RG
%CRKNNCT[6WDG
4GHTKIGTCPV
4#
4#
4#
2TQRGT/CVGTKC
3WCPVKV[
10Ⳇ×2TANK
10Ⳇ×3TANK
5Ⳇ×2TANK
%QPVTQN/GVJQF
6QTSWGCPF6%%QPVTQN
/+%1/%QPVTQN
2TQXKUKQPU
7UGT/CPWCN
'#
7UGT/CPWCN
'#
'FKDNG)TGCUG
'# 'FKDNG)TGCUG
'#
4WDDGT4KPI
'#
4WDDGT4KPI
'#
4WDDGT2CEMKPI
'# 4WDDGT2CEMKPI
'#
.COR
'#
.COR
'#
7UGT/CPWCN
'#
'FKDNG)TGCUG
'#
4WDDGT4KPI
'#
4WDDGT2CEMKPI
'#
/KUEGNNCPGQWU
1RGTCVKQP
'PXKTQPOGPV
Important
ST12 x 2
#ODKGPV6GORGTCVWTG`Ⳅ
The raw material quantity may vary by the material type and sugar content.
If the slush touches the cover, reduce the quantity of the raw material.
19
10. Circuit Diagram
SSM-52
MI7.5X2
CIRCUIT DIAGRAM
SI12X2
CIRCUIT DIAGRAM
20
SI12X3
CIRCUIT DIAGRAM
21
11. Before Calling Service
Failure
If power is not supplied
The spiral rotation is
stopped.
(Noise is generated.)
Cause
1. Power is not supplied from
the outlet.
2. The power switch is turned
off.
1. Check the outlet connection
status.
3. The fuse is disconnected.
3. Replace the fuse.
Low sugar level in the material.
(The spiral is frozen.)
Turn off the power switch and melt
the ice.
(At this time, do not use a sharp
tool such as ice pick.)
After that, retry.
1. The material level is too low.
While operation, water
flowing sound is heard.
It is too much frozen.
22
2. Turn on the power switch.
Deformation of the spiral and canister.
(It can happen when hot water (80 or
Replace the spiral and canister.
above) is used while cleaning and sterilizing
the product.)
Spiral rotation shaft wear (wear of
the part that meets the spiral
Replace the spiral.
rotation shaft in the middle of the
cylinder)
The material does not
The material level is too low.
come out from the slush
supply.
The material is too much frozen.
The granita is not
formed.
Action
2. The sugar level is set to
Weak (Level 1).
3. It is set to Stop or
Refrigeration.
The sound is heard when the
refrigerant flows.
The freezing switch is turn on
continually.
Fill the material up to three litters.
Adjust the control screw on the cover of
the motor (on the rear of the product).
1. Replace the material
(sugar level: 13 to 15%)
2. Connect the cord of the cap.
3. Set it to Freezing.
Normal operation
Adjust the freezing and refrigeration
switch to have optimal temperature. In
this case, set the switch to Refrigeration
or Stop.
2CTV.KUV
MI7.5X2: OUT CASE ASSEMBLY
!
!
! "
! $
! "
!
! %
$! = &
% #
!
23
SSM-280,ST12X3:
420 IN CASE
ASSEMBLY
ST12X2,
IN CASE
ASSEMBLY
24
!
!
= &
" ! !
!
!
!
=
& ##
=&
SSM-280,ST12X3:
420 OUT CASE
ST12X2,
OUT ASSEMBLY
CASE ASSEMBLY
!
!
! "
%
!
!
! $
!
! "
$!
! % #
25
CANISTER ASSEMBLY
NO
26
ITEM
NO
1
Canister Cover
9
Moter cover
17
Packing Redenar One
2
Canister
10
Geared Motor
18
Pin Lever
3
Spiral
11
Micro switch
19
Packing Down
4
Packing back
12
ASS'Y Drum
20
O-ring down
5
Dasher Shaft
13
Base Canister
21
Lever Shaft
6
Tension Bolt
14
Packing Cushion
22
Lever Spring Slush
7
Joint Spring
15
Redenar
23
Lever Label
8
Insert Joint Spring
16
Redenar Bushing
24
Lever
ITEM
NO
ITEM
13. When Receiving Service
1. A product failure has
occurred while operation.
2. First turn off the power switch
and remove the power plug.
3. Contact the service agency.
4. The service engineer visits and
performs service upon call.
5. The repair is finished! !
6. When you are using the clover service of the manufacturer,
the service history is logged in the system for more efficient services.
27
Product Warranty Card
Product
Name
Model Name
Serial
Slush & Smoothie Machine
Number
Purchased
1 year after purchasing the
Date
Year____ Month______ Day____
Warranty Expiration
Year____ Month______ Day____
Customer
Address
Customer
Name
Phone
Warranty Period
SSM-180,ST12x3,
280, 420,MI7.5x2
560, 52
ST12x2,
product
Year____ Month______Until
Number
1. The free-of-charge service is provided within the warranty period about the
failures issued while normal operations.
2. After checking the user manual, contact the service agency for the failures.
3. Charged service is provided even within the warranty period in the following cases:
- Failure caused by careless use or improper repair/modification.
- Failure caused by not following the instructions in this user manual.
4. Repair after warranty expiration: Charged service is provided.
5. For repair, provide the product warranty card to the service engineer.
6. This product warranty card is applied in the local area.
7. This card is not reissued so please keep it in a safe place.
ⷅContact Details :
BLUE ICE MACHINES LIMITED
TEL: 0208442 4001
Website: www.blueicecreammachine.co.kr
email: info@blueicecreammachine.co.kr
28
Download PDF
Similar pages