Ilumipod Inground Tri-3 IP Optic WW User Manual Rev. 7

Ilumipod Inground Tri-3 IP
Optic 25 WW
User Manual
Edition Notes
Edition Notes
The Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7 covers the description,
safety precautions, installation, programming, operation, and maintenance of the Ilumipod
Inground Tri-3 IP Optic 25 WW. ILUMINARC® released this edition of the Ilumipod
Inground Tri-3 IP Optic 25 WW User Manual Rev. 7 in March 2016.
Trademarks
The ILUMINARC® logo, the ILUMINARC® name and all other trademarks in this document
related to services or products by ILUMINARC® are trademarks owned or licensed by
ILUMINARC®, its affiliates or subsidiaries. Any other product names, logos, brands,
company names, trademarks featured or referred to within this document are the property of
their respective trademark holders.
Copyright Notice
The entire content of this document, except where applicable and unless otherwise noted, is
solely owned by ILUMINARC®, a wholly owned trademark of Chauvet & Sons, LLC.
© Copyright 2016 ILUMINARC®.
All rights reserved.
Electronically published by ILUMINARC® in the United States of America.
Manual Usage
ILUMINARC® authorizes its customers to download and print this manual for professional
information purposes only. ILUMINARC® expressly prohibits the usage, copy, storage,
distribution, modification, or printing of this manual or its content for any other purpose
without its written consent.
Document Printing
For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If
using A4 paper (210 x 297 mm), configure your printer to scale the content of this document
to A4 paper.
Intended Audience
Any person in charge of installing, operating, and/or maintaining the Ilumipod Inground Tri-3
IP Optic 25 WW should read both the guide that shipped with it and this User Manual in their
entirety before installing, operating, or maintaining this product.
Disclaimer
ILUMINARC® believes that the information contained in this manual is accurate in all
respects. However, ILUMINARC® assumes no responsibility for any error or omissions in
this document. ILUMINARC® reserves the right to revise this document and to make changes
from time to time in the content hereof without obligation of ILUMINARC® to notify any
person or company of such revision or changes. This does not constitute in any way a
commitment by ILUMINARC® to make such changes. ILUMINARC® may issue a revision
of this manual or a new edition of it to incorporate such changes.
Document Revision
The Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 6 supersedes all previous
versions of this manual. Please discard any older versions of this manual you may have,
whether in printed or electronic format, and replace them with this version.
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Table of Contents
Table of Contents
1. Introduction .......................................................................................................................... 1
What Is In the Box .............................................................................................................................. 1
Unpacking Instructions ....................................................................................................................... 1
Claims....................................................................................................................................................... 1
Text Conventions................................................................................................................................ 1
Safety Notes....................................................................................................................................... 2
Personal Safety ......................................................................................................................................... 2
Mounting and Installation ........................................................................................................................... 2
Power and Wiring ...................................................................................................................................... 2
Operation .................................................................................................................................................. 2
2. Product Description ............................................................................................................. 3
Features ............................................................................................................................................. 3
Additional Equipment ................................................................................................................................. 3
Overview ............................................................................................................................................ 4
Dimensions ........................................................................................................................................ 5
3. Installation ............................................................................................................................ 6
Installation Notes ................................................................................................................................ 6
Installation Sleeve Orientation .................................................................................................................... 6
Installation Sleeve Setup............................................................................................................................ 6
AC Power ........................................................................................................................................... 7
Power Consumption .................................................................................................................................. 7
AC Plug..................................................................................................................................................... 7
Power Wiring ............................................................................................................................................. 7
DMX Linking ....................................................................................................................................... 8
DMX Modes .............................................................................................................................................. 8
Signal Wiring ............................................................................................................................................. 8
Protocol Connectivity ................................................................................................................................. 8
Controllers.......................................................................................................................................... 9
DMX Controller .......................................................................................................................................... 9
Ilumicode Addresser ................................................................................................................................ 10
4. Operation ............................................................................................................................ 11
Ilumicode Addresser ......................................................................................................................... 11
Ilumicode Panel Description ..................................................................................................................... 11
Control Options ................................................................................................................................ 11
Programming.................................................................................................................................... 11
DMX Personality ...................................................................................................................................... 11
DMX Starting Address ............................................................................................................................. 11
Static Colors ............................................................................................................................................ 12
Dimmer ................................................................................................................................................... 12
Reset to Factory Settings ......................................................................................................................... 12
Menu Map ........................................................................................................................................ 12
DMX Values ..................................................................................................................................... 12
SOLID ..................................................................................................................................................... 12
5. Technical Information ........................................................................................................ 13
Product Maintenance ........................................................................................................................ 13
Product Repairs................................................................................................................................ 13
Troubleshooting Guide ..................................................................................................................... 14
Photometrics .................................................................................................................................... 15
LED Disclaimer................................................................................................................................. 16
LED Life .................................................................................................................................................. 16
LED Binning ............................................................................................................................................ 16
Color Rendering Index (CRI) .................................................................................................................... 16
Returns Procedure ........................................................................................................................... 17
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
i
Table of Contents
Contact Us .............................................................................................................................. 17
Technical Specifications ................................................................................................................... 18
ii
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Introduction
1. Introduction
Critical
installation,
configuration, or
operation information.
Failure to comply with this
information may render the
product partially or
completely inoperative,
damage third-party
equipment, or cause harm
to the user.
Important
installation or
configuration
information. Failure to
comply with this
information may prevent
the product from
functioning correctly.
Useful
information.
What Is In the Box
• Ilumipod Inground Tri-3 IP Optic 25 WW
• Installation Sleeve
• Warranty Card
• Quick Reference Guide
Unpacking Instructions
Immediately upon receiving a product from ILUMINARC®, carefully unpack the carton.
Check the contents of the box to ensure that all parts are present and that they are in good
condition.
Claims
The carrier is responsible for any damage incurred during shipping. Therefore, if the received
merchandise appears to have been damaged during shipping, the customer must submit the
damage report and any related claims to the carrier, not ILUMINARC®. The customer must
submit the report upon receipt of the damaged merchandise. Failure to do so in a timely
manner may invalidate the customer’s claim with the carrier.
For other issues such as missing components or parts, damage not related to shipping, or
concealed damage, the customer must make claims to ILUMINARC® within 7 days of
receiving the merchandise.
Text Conventions
The term “DMX”
used throughout
this document
refers to the USITT
DMX512-A transmission
protocol.
Convention
1–512
50/60
DMX Primer
<SET>
Settings
MENU > Settings
1–10
Yes/No
ON
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Meaning
A range of values in the text
A set of mutually exclusive values in the text
The name of another publication or manual
A button on the product’s control panel
A product function or a menu option
A sequence of menu options
A range of menu values from which to choose in a menu
A set of two mutually exclusive menu options in a menu
A unique value to enter or select in a menu
1
Introduction
Safety Notes
There are no
user-serviceable
parts inside this
product. Any reference to
servicing you may find in
this User Manual will only
apply to properly certified
ILUMINARC® technicians.
Do not open the housing
or attempt any repairs
unless you are certified to
do so.
Please read all the following Safety Notes carefully because they include important
information on how to install, use, and maintain this product safely.
Personal Safety
• Avoid direct eye exposure to the light source while the product is on.
• Always disconnect this product from its power source before servicing.
• Always connect this product to a grounded circuit to avoid the risk of electrocution.
• Do not touch this product’s housing when operating because it may be very hot.
Mounting and Installation
• This product is for outdoor use and can be submerged (IP67). However, do not
submerge deeper than 1 m for more than 30 minutes.
Please refer to all
applicable local
codes and
regulations for the proper
installation of this product.
Keep this
manual for
future
consultation. If
you sell this product to
another user, make sure
that they also receive this
manual.
In the unlikely
event that your
Ilumipod
Inground Tri-3 IP
Optic 25 WW may require
service, please contact
ILUMINARC® Technical
Support.
2
• Make sure there are no flammable materials close to this product while it is operating.
Power and Wiring
• Always make sure that you are connecting this product to the proper voltage, as per the
specifications in this User Manual or on the product’s sticker.
• CAUTION: When transferring product from extreme temperature environments, (e.g.
cold truck to warm humid ballroom) condensation may form on the internal electronics
of the product. To avoid causing a failure, allow product to fully acclimate to the
surrounding environment before connecting it to power.
• Never connect this product to a dimmer pack.
• Make sure that the power input cable is not cracked, crimped, or damaged.
• Never disconnect this product by pulling or tugging on the power input cable.
Operation
• The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at a
higher temperature.
• In case of a serious operating problem, stop using this product immediately!
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Product Description
2. Product Description
The Ilumipod Inground Tri-3 IP Optic 25 WW is a wash light intended for in-ground
installation. The product consists of a cast aluminum body containing a power supply, control
unit, drive-over-rated glass lens cover, and tri-emitter LEDs.
Features
• 1-channel warm white LED in-ground wash light
• Operating mode, 1-channel: Dimmer
• Five distinct dimming curves
• IP67 stainless steel gland nuts for cable entry
• Remotely addressable with Ilumicode Addresser
• IP67 ingress protection
• GORE™ valve
• Drive-over-rated glass lens cover
• High-power, 2.3 W (700 mA) tri-emitter LEDs
Additional Equipment
• Ilumicode addresser required for product configuration (sold separately)
• The RDM2go, which includes a built-in Ilumicode addresser along with many other useful
features, is now available.
• The Ilumicode addresser is required for product configuration (sold separately).
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
3
Product Description
Overview
Installation
Sleeve
316 Stainless
Steel Gland Nuts
Tri-emitter LEDs
4
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Product Description
Dimensions
0.2 in
(4 mm)
5.6 in
(141 mm)
7 in
(178 mm)
4.2 in
(107 mm)
6.0 in
(153 mm)
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
5
Installation
3. Installation
Installation Notes
Always keep the
power cables away
from the signal
cables by running
them in different conduits
and using separate
distribution boxes.
This product is
intended for
installation into
concrete or other hard pan
substrate. It is not intended
for installation into soft
substrates including, but not
limited to, soil or mulch.
The Ilumipod Inground Tri-3 IP Optic 25 WW consists of two parts: the product housing and the
concrete installation sleeve. The product housing is IP67-rated. The installation sleeve is not.
Read the Installation Sleeve Setup instructions carefully.
Do not use the product’s junction box to extend the power or signal cables to other units. This
might compromise the IP rating of the junction box. Instead, use individual cables from the
product to the corresponding distribution boxes.
Installation Sleeve Orientation
You will have to run the AC power and signal cables from the base of the fixture into the
installation sleeve. Position the installation sleeve so that the signal cable exits the sleeve using
one of the two cable outlets. Use the opposite outlet for the power cable (refer to the following
figure). This method will reduce the stress to the signal and power cables when setting the
product down, while keeping them separated under the product’s housing.
Signal
cable
Power
cable
To power
distribution box
To signal
distribution box
Installation Sleeve Setup
When setting up the installation sleeve, make sure that any water that may have entered can drain
out of the sleeve. Locate the installation sleeve above the normal drainage level so the product is
never under more than 1 m of water for more than 30 minutes (IP67) during heavy rain.
In addition, make sure that the installation sleeve and the stainless steel collar are horizontal and
even with the ground surface. This helps distribute the load uniformly over the product’s surface
and avoids creating dangerous bumps.
Ilumipod Inground
Tri-3 IP Optic 25 WW
products can support
a distributed load of up to
3,000 kg (6,614 lb) when
properly installed.
6
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Installation
Always connect
the Ilumipod
Inground Tri-3 IP
Optic 25 WW to a
protected circuit with an
appropriate electrical
ground to avoid the risk of
electrocution or fire.
Never connect
the Ilumipod
Inground Tri-3 IP
Optic 25 WW to a rheostat
(variable resistor) or
dimmer circuit, even if the
rheostat or dimmer
channel serves only as a
0 to 100% switch.
Make sure to
connect the
Ilumipod
Inground Tri-3 IP Optic 25
WW to a power line with
the proper voltage and
frequency, as per the
specifications in this User
Manual or on the product’s
sticker.
AC Power
The Ilumipod Inground Tri-3 IP Optic 25 WW has an auto-ranging power supply that works
with an input voltage range of 100~240 VAC, 50/60 Hz.
Make sure that you are connecting this product to the proper voltage, as per the specifications
in this User Manual or on the product’s sticker.
Power Consumption
To determine the power requirements for the Ilumipod Inground Tri-3 IP Optic 25 WW, refer
to the label affixed to the side of the product. Alternatively, you may refer to the Technical
Specifications.
The listed current rating indicates the maximum current draw during normal operation.
AC Plug
The Ilumipod Inground Tri-3 IP Optic 25 WW comes with a bare-ended power input cord for
hardwired installation. Use the table and the illustration below to wire a plug.
Connection
AC Live
AC Neutral
AC Ground
Wire (U.S.)
Black
White
Green/Yellow
Screw Color (U.S.)
Yellow or Brass
Silver or Gray
Green
Wire (Europe)
Brown
Blue
Green/Yellow
IP67 Pin
1
2
3
Power Wiring
The listed current
rating indicates
the maximum
current draw
during normal operation.
You can connect the bare-ended, IP67-rated AC power cable from the product to an IP67-rated
power connector or IP67-rated junction box.
If using junction boxes, make sure to use IP67-rated conduit for surface installations.
If you choose to
bury the power or
signal distribution
boxes, make sure that
they are IP67-rated or
greater.
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
7
Installation
The Ilumipod
Inground Tri-3 IP
Optic 25 WW
must be linked using DMX
cable in a daisy chain
(serial) fashion. To
comply with the EIA-485
standard, no more than
32 products should be
connected on one daisy
chain without using a
DMX optically isolated
splitter. Doing otherwise
may result in deterioration
of the digital DMX signal.
USITT
recommends
limiting the total
length of the DMX cable
(from the first
product/controller to the
last product) to 300–455
m (985–1,500 ft).
Disconnect the
product from the
AC power before
opening it.
The signal cable
must match or
exceed the
electrical characteristics
of the Belden® 9841
cable for EIA RS-485
applications. You may
also use CAT5, 5e, or
CAT6 LAN cable.
8
DMX Linking
You may link the Ilumipod Inground Tri-3 IP Optic 25 WW to a DMX controller using a
standard DMX serial connection. If using other DMX products compatible with the Ilumipod
Inground Tri-3 IP Optic 25 WW, you can control each individually with a single DMX
controller.
If you are not familiar with the DMX standard, or if you need information about the DMX
cables needed to link the Ilumipod Inground Tri-3 IP Optic 25 WW to a DMX controller, you
may download the DMX Primer from the ILUMINARC® website at
http://www.iluminarc.com/reports/dmx-primer.
DMX Modes
The Ilumipod Inground Tri-3 IP Optic 25 WW uses the standard DMX data connection for its
SOLID personality. Refer to the Introduction chapter for a brief description of this mode.
Refer to the Operation chapter to learn how to configure the Ilumipod Inground Tri-3 IP Optic
25 WW to work in this mode. The DMX Values section provides detailed information
regarding the DMX mode.
DMX Mode
SOLID
DMX Address
512
Signal Wiring
To provide signal for the Ilumipod Inground Tri-3 IP Optic 25 WW, you can connect the bareended, IP67-rated signal cable from the product to two IP67-rated signal connectors
(DMX In/DMX Out) or use an IP67-rated junction box. In this case, make sure to use
IP67-rated conduit.
Protocol Connectivity
The Ilumipod Inground Tri-3 IP Optic 25 WW uses the USITT DMX 512 Protocol. The
procedure below illustrates the recommended connection method.
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Installation
Controllers
If you have not
configured the
DMX starting
address and
DMX mode for each
product, they will all use
their default values. This
means that all products
will operate in unison.
The Ilumipod Inground Tri-3 IP Optic 25 WW can operate with a standard DMX controller or
the ILUMICODE addresser. The sections below provide information on how to connect these
products to the corresponding controllers. The instructions to operate these products with each
of the above controllers are in the Operation chapter of this manual.
DMX Controller
The Ilumipod Inground Tri-3 IP Optic 25 WW can work with a standard DMX controller. The
channel assignments will depend on the chosen personality (see the corresponding Menu Map
section) and the DMX address assigned to each product (see the Programming section).
The figure below illustrates how to connect the DMX controller to the Ilumipod Inground Tri-3
IP Optic 25 WW.
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
9
Installation
To assign individual
DMX addresses to
each product, you
must connect the
Ilumicode addresser to each
product, individually.
ILUMINARC®
suggests that you
connect no more
than 20 products in
this mode and keep the total
distance to less than 60 m
(197 ft). Otherwise, you
might need to use an
optically isolated signal
amplifier.
Ilumicode Addresser
The Ilumipod Inground Tri-3 IP Optic 25 WW uses the Ilumicode addresser (“Ilumicode”) for
configuration purposes. The diagram below shows how to connect the Ilumicode to this product.
This connection will control multiple products at the same time, all having the same DMX
address.
Important: The Ilumicode must be used to configure this product. The Ilumicode can be
purchased separately through your ILUMINARC® sales representative.
The RDM2go, which
includes a built in
ilumicode addresser
along with many other useful
features is now available.
10
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Operation
4. Operation
Ilumicode Addresser
The Ilumipod Inground Tri-3 IP Optic 25 WW needs an external controller, the Ilumicode
addresser (“Ilumicode”), to change its configuration.
Ilumicode Panel Description
Button
<MENU>
<ENTER>
<UP>
<DOWN>
<POWER>
Function
Exits from the current menu or function.
Enables the currently displayed menu or sets the
currently selected value into the selected
function.
Navigates upwards through the menu list and
increases the numeric value when in a function.
Navigates downwards through the menu list and
decreases the numeric value when in a function.
Turns the unit on. The unit will turn off
automatically after 30 seconds of inactivity.
Control Options
You can set the Ilumipod Inground Tri-3 IP Optic 25 WW start address in the 001–512 DMX
range. This allows for the control of up to 512 products in the 1-channel SOLID personality.
Programming
Carry out all the programming procedures indicated below from the control panel. Refer to
the Menu Map section to learn how the menu options relate to each other.
Use <ENTER> and <MENU> to change levels in the Menu Map, moving right and left,
respectively. Use <UP> and <DOWN> to move vertically within the Menu Map.
DMX Personality
When you scroll
through the
menu options,
you will see
many of them that do not
correspond with the menu
map. Skip them, as they
do not work with the
WW-only output
products.
1. Go to PERSON and select SOLID personality.
2. Make sure to rearrange the DMX addresses of all products in the current DMX
universe to avoid address overlapping.
DMX Starting Address
1. Go to DMX.
2. Select a starting DMX address (001–512).
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
11
Operation
Static Colors
1. Go to STATIC.
2. Select a color (COOL).
3. Select a color value 000~255 (0–100%).
Dimmer
DIM1 is the
fastest dimming
curve and DIM4
is the slowest.
This setting gives the user four different options to simulate the dimming curve of an
incandescent lighting product.
1. Go to DIMMER.
2. Select a dimming curve (OFF or DIM1–4).
Procedure:
DIMMER
OFF
DIM1
DIM2
DIM3
DIM4
Description
Dimmer curve is linear with fader
Non-linear (fastest)
Non-linear (fast)
Non-linear (slow)
Non-linear (slowest)
Reset to Factory Settings
1. Go to SETTINGS > RESET.
2. Select YES or NO.
Menu Map
Main Level
Programming Levels
Description
DMX
001–512
Sets the DMX starting address
PERSON
SOLID
1-channel: Dimmer
DIMMER
OFF
Dimmer works in linear mode
DIM1
Dimmer works in non-linear mode, from fast to slow
DIM2
DIM3
DIM4
STATIC
COOL
000–255
SETTINGS
RESET
YES
Configures the static color
Resets unit to factory default settings
NO
DMX Values
SOLID
Channel
1
12
Function
Dimmer
Value
000  255
Percent/Setting
0–100%
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Technical Information
5. Technical Information
Product Maintenance
Always dry the
external optics
and glass
surfaces carefully
after cleaning them.
If you still
experience
technical
problems after
trying the solutions in the
Troubleshooting Table,
contact ILUMINARC ®
Technical Support.
To maintain optimum performance and minimize wear, clean the products frequently. Usage
and environment are contributing factors in determining the cleaning frequency. As a general
guideline, products should be cleaned at least twice a month. Dust build-up reduces light
output, performance, and can cause overheating. This can lead to reduced light source life.
For products containing external optical lenses, clean them periodically to optimize light
output. The cleaning frequency depends on the environment in which the product operates.
Damp, smoky, or particularly dirty surrounding can cause greater accumulation of dirt on the
product’s optics, requiring more frequent cleaning.
To clean a product:
• Disconnect the product from power.
• Wait until the product is at room temperature.
• Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the
external surfaces.
• Clean all external glass optics and glass surfaces with a mild solution of glass cleaner or
isopropyl alcohol, and a soft, lint-free cotton cloth or lens-cleaning tissue.
• Apply the solution directly to the cloth or tissue and wipe any dirt and grime to the outside
edge of the lens. Gently polish the external glass surfaces until they are free of haze and
lint.
Product Repairs
ILUMINARC® strongly advises you against attempting any repairs to this product unless you
are an authorized ILUMINARC® technician.
ILUMINARC® presents the information contained in the Troubleshooting Guide as potential
solutions only. In most cases, opening the product’s housing will invalidate its warranty.
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
13
Technical Information
Troubleshooting Guide
Symptom
Cause(s)
Circuit breaker/fuse keeps Excessive circuit load
tripping/blowing
Short circuit along the power wires
No power
Product does not power up Loose or damaged power cord
Faulty internal power supply
Wrong DMX addressing
Damaged DMX cables
Product does not respond to Wrong polarity on the controller
DMX
Loose DMX cables
Faulty DMX interface
Faulty Display/Main board
Non-DMX cables
Bouncing signals
DMX signal problems
Long cable/low level signal
Too many products
Interference from AC wires
14
Action(s)
Check total load placed on the electrical
circuit
Check for a short in the electrical wiring
Check for power on power outlet
Check power cord
Return for service to ILUMINARC®
Check Control Panel and product addressing
Check DMX cables
Check polarity switch settings on the
controller
Check cable connections
Return for service to ILUMINARC®
Return for service to ILUMINARC®
Use only DMX-compatible cables
Install terminator as suggested in the DMX
Primer from the ILUMINARC® website at
http://www.iluminarc.com/reports/dmxprimer.
Install an optically coupled DMX splitter
right after the product with the strong signal
Install an optically coupled DMX splitter
after product #32 or before
Keep DMX cables separated from power
cables or fluorescent/black lights
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Technical Information
Photometrics
Filename: ILUMIPOD INGROUND TRI-3 IP OPTIC (25°) WW
Manufacturer: ILUMINARC®
Luminaire: Ilumipod Inground Tri-3 IP Optic 25 WW
Lamp Output: 1 lamp, rated lumens/lamp: 400
Max Candela: 2,885.7 at Horizontal: 0°, Vertical: 1°
Input Wattage: 9.8
Luminous Opening: Point
Test: 20120523
Test Date: 2012-05-23
Test Lab: ILUMINARC R&D
Photometry : Type B
CIE Class: Direct
Flood Summary
Efficiency
Lumens
Horizontal Spread
Vertical Spread
Field (10%):
52.7%
210.6
29.1
29
Beam (50%):
23.7%
94.9
15.2
14.5
Total:
62.5%
250.0
Photometrics Pro 1.3.21 copyright 2003-2012 by jSolutions, Inc.
Reported data calculated from manufacturer's data file, based on IES recommended methods.
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
15
Technical Information
LED Disclaimer
LED Life
ILUMINARC® rates LED lifetime based on lumen depreciation of 70% of the original output,
with data provided by the manufacturer of the LED. Data from the manufacturer of the LED
are not independently verified or measured by ILUMINARC®. When the product is operating
in optimal environmental conditions, the LED lifetime is rated to be 50,000 to 70,000 hours by
the LED manufacturer.
LED Binning
LED manufacturers sort LEDs into “bins,” based on variances in color, output intensity, and
the frequency at which the semiconductor operates. ILUMINARC® strives to hold its LED
manufacturers to the highest standards of binning to optimize consistency in output from
product to product. However, the availability of a single bin cannot be guaranteed. With that in
mind, ILUMINARC® has developed a rigorous control system to seek the best-achievable
consistency in color and output.
Color Rendering Index (CRI)
CRI is an industry standard method to compare properties of different types of light sources.
There are known limitations and inconsistencies related to CRI. Results may vary depending
on the environmental factors involved. For this reason, the U.S. Department of Energy (DOE)
states that CRI should be considered as one point of reference among others in evaluating
white LED products and systems.
The following is an excerpt of recommendations from the DOE:
1. Identify the visual tasks to be performed under the light source. If color fidelity under
different light sources is critically important (for example, in a space where color or
fabric comparisons are made under both daylight and electric lighting), CRI values may
be a useful metric for rating LED products.
2. CRI may be compared only for light sources of equal correlated color temperature.
This applies to all light sources, not only to LEDs. Also, differences in CRI values of
less than five points are not significant, e.g., light sources with 80 and 84 CRI are
essentially the same.
3. If color appearance is more important than color fidelity, do not exclude white light
LEDs solely on the basis of relatively low CRI values. Some LED products with CRIs
as low as 25 still produce visually pleasing white light.
4. Evaluate LED systems in person and, if possible, on-site when color fidelity or color
appearance are important issues.
Source: DOE publication: PNNL-SA-56891, January 2008
16
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Technical Information
Returns Procedure
ILUMINARC®
reserves the right
to use its own
discretion to repair or
replace returned
product(s).
Always keep the
original box and
all packaging
material as you
will need those to ship the
product back to
ILUMINARC®.
Contact
Us
You must send the merchandise prepaid, in the original box, and with its original packing and
accessories. ILUMINARC® will not issue call tags.
Call ILUMINARC® and request a Return Merchandise Authorization Number (RMA #)
before shipping the product. Be prepared to provide the model number, serial number, and a
brief description of the cause for the return.
The user must clearly label the package with an RMA #. ILUMINARC® will refuse any
product returned without an RMA #. DO NOT write the RMA # directly on the box.
Instead, write it on a properly affixed label.
Once you receive the RMA #, please include the following information on a piece of
paper inside the box:
• Your name
• Your address
• Your phone number
• The RMA #
• A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be the customer’s responsibility. FedEx packing or double-boxing are
recommended.
USA WORLD HEADQUARTERS
General Information – ILUMINARC
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: (954) 923-3680
Fax:
(800) 544-4898
Technical Support
Voice: (800) 762-1084
Email: support@iluminarc.com
World Wide Web www.iluminarc.com
EUROPE
General Information - Chauvet Europe BVBA
Address: Stokstraat 18
9770 Kruishoutem
Belgium
Voice: +32 9 388 93 97
Technical Support
Email: Eutech@chauvetlighting.eu
General Information - Chauvet Europe Ltd.
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: +44 (0)1773 511115
Fax:
+44 (0)1773 511110
Technical Support
Email: uktech@iluminarc.com
World Wide Web www.chauvetlighting.eu
World Wide Web
www.chauvetlighting.co.uk
MEXICO
General Information - Chauvet Mexico
Address: Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice: +52 (728) 285-5000
Technical Support
Email: servicio@iluminarc.com.mx
World Wide Web www.chauvet.com.mx
Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux contact the dealer of record. Follow
their instructions to request support or to return a product. Visit our website for contact details.
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
17
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual
Technical Specifications
Dimensions and Weight
Electrical
Light Source
Length
Width
Height
6.0 in (153 mm)
6.0 in (153 mm)
7.0 in (178 mm)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power Supply Type
Range
Switching (internal)
100 to 240 VAC, 50/60 Hz
Parameter
120 V, 60 Hz
Consumption
10 W
Operating current
0.2 A
Power I/O
Input
Connectors
Open Wire
Cord plug
N/A
Type
Power
LED
Color
Temperature
Warm White
3100 K
Parameter
Illuminance @ 5 m
Beam angle
Field angle
Max. External Temperature
113 °F (45 °C)
I/O Connectors
Open Wire
Product Name
Ilumipod Inground Tri-3 IP
Optic 25 WW
Color
Photometric
Thermal
DMX
Ordering
18
Weight
4.6 lb (2.0 kg)
Voltage Selection
Auto-ranging
230 V, 50 Hz
11 W
0.1A
Output
N/A
N/A
Lifespan
2.3 W
Quantity
50,000 hours
Current
3
Standard 25º Optics
100 lx
15°
29°
Cooling System
Convection
Connector Type
Open Wire
Item Code
700 mA
Channel Range
1
UPC Number
01630585
781462209339
Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7
Download PDF
Similar pages