_Ó¢ÎÄÓû§ÊÖ²áCDP 2L1049W

Dishwasher
Instruction Manual
CDP 2L1049W-80
1) Safety Information.........................................1
Read this Manual
Dear Customer,
Please carefully read this manual before using the
dishwasher, it will help you to use and maintain the
dishwasher properly.
Keep it to refer to it at a later date.
Pass it on to any subsequent owner of the appliance.
This manual contains sections on safety Instructions,
Operating Instructions, Installation Instructions and
Troubleshooting Tips, etc.
2) Quick operation guide.................................... 2
3) Operation Instruction.....................................3
Control Panel...................................................3
Dishwasher Features.................................... ...3
4) Prior using for the first time............................4
A Water Softener...........................................4
B Loading the Salt into the Softener.................5
C Loading the Detergent................................6
D Type of Detergent ......................................7
5) Loading the Dishwasher Basket.....................9
Before Calling for Service
To review the section on troubleshooting Tips
will help you to solve some common problems
by yourself .
If you can not solve the problems by yourself ,
please ask for the help of professional technicians.
NOTE:
The manufacturer, following a policy of constant
development and updating of the product, may
make modifications without giving prior notice.
This user manual shall also be got from the
manufacturer or responsible vendor.
Recommengation...........................................9
For washing in the dishwasher the
folliwing cutlery/dishes...................................9
Attention before or after loading the
Dishwasher Baskets.......................................9
Removing the Dishes................................... ...9
The Method Loading Normal Dishware......... ...10
6) Starting a washing programme.....................11
Wash Cycle Table...........................................11
Turning on the Appliance................................11
Change the Programme..................................12
Forgot to Add a Dish.......................................12
At the end of the Wash Cycle...........................12
7) Maintenance and cleaning............................13
Filtering System.............................................13
Caring for the Dishwasher...............................14
8) Installation instruction................................15
Positioning the Appliance...............................15
About Power Connection................................15
Water Connection..........................................16
Start of dishwasher........................................17
9) Troubleshooting Tips...................................18
Before calling for service.................................18
Error codes...................................................19
Technical information.....................................20
Loading the baskets according to En50242
1.IMPORTANT SAFETY INFORMATION
WARNING! When using your dishwasher,
follow the precautions listed below:
This appliance is intended to be used in household and similar
applications such as:
-staff kitchen areas in shops, offices and other working environments;
-farm houses;
-by clients in hotels, motels and other residential type environments;
-bed and breakfast type environments.
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without supervision.
For EN60335-1
This appliance is not intended for use by persons(including children )with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
For IEC60335-1
This appliance is for indoor use only, for household use only. To protect
against the risk of electrical shock, do not immerse the unit, cord or plug in
water or other liquid.
Please unplug before cleaning and maintenance the appliance .Use a soft
cloth moisten with mild soap, and then use a dry cloth to wipe it again .
EARTHING INSTRUCTIONS
This appliance must be earthed. In the event of a malfunction or breakdown,
earthing will reduce the risk of an electric shock by providing a path of least
resistance of electric current. This appliance is equipped with a cord having
an equipment-earthing conductor and a earthing plug.
The plug must be plugged into an appropriate outlet that is installed and
earth ed in accordance with all local codes and ordinances.
Improper connection of the equipment-earthing conductor can result
in the risk of an electric shock. Check with a qualified electrician or service
representative if you are in doubt whether the appliance is properly earthed.
Do not modify the plug provided with the appliance; If it does not fit the outlet.
Have a proper outlet installed by a qualified electrician.
1-1
Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.
Do not operate your dishwasher unless all enclosure panels are properly in place.
Open the door very carefully if the dishwasher is operating, there is a risk of water
squirting out.
Do not place any heavy objects on or stand on the door when it is open. The
appliance could tip forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely to damage the door seal;
2) Warning: Knives and other utensils with sharp points must be loaded in the
basket with their points down or placed in a horizontal position.
Check that the detergent powder is empty after completion of the wash cycle.
Do not wash plastic items unless they are marked dishwasher safe or the
equivalent. For plastic items not so marked, check the manufacturer's
recommendations.
Use only det ergent and rinse additives designed for an aut omatic dishwasher.
Never use soap, laundry detergent, or hand washing detergent in your dishwasher.
Children should be supervised to ensure that they do not play with the appliance.
The door should not be left open, since this could increase the risk of tripping.
If the supply cord is damaged, it must be replaced by the manufacturer or
its service agent or a similarly qualified person in order to avoid a hazard.
During installation, the power supply must not be excessively or dangerously
bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water mains using new hose sets and
that old hose-sets should not be reused.
The maximum number of place settings to be washed is 10.
The maximum permissible inlet water pressure is 1MPa.
The minimum permissible inlet water pressure is 0.04MPa.
1-2
Disposal
This appliance is marked according to the European
directive 2012/19/EU on Waste Electrical and Electronic
Equipment (WEEE).
WEEE contains both polluting substances (which can
cause negative consequences for the environment)
and basic components (which can be re-used).
It is important to have WEEE subjected to specific
treatments, in order to remove and dispose properly all
pollutants, and recover and recycle all materials.
Individuals can play an important role in ensuring that
WEEE does not become an environmental issue;
it is essential to follow some basic rules:
WEEE should not be treated as household waste;
WEEE should be handed over to the relevant collection
points managed by the municipality or by registered
companies. In many countries, for large WEEE,
home collection could be present.
In many countries, when you buy a new appliance, the
old one may be returned to the retailer who has to collect
it free of charge on a one-to-one basis, as long as the
equipment is of equivalent type and has the same
functions as the supplied equipment.
WARNING!
Packaging material could be dangerous for children!
For disposing of package and the appliance please go to a
recycling centre. Therefore cut off the power supply cable
and make the door closing device unusable.
Cardboard packaging is manufactured from recycled paper
and should be disposed in the waste paper collection for
recycling.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this
product, please contact your local city office and your
household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted
municipal waste. Collection of such waste separately for
special treatment is necessary.
By placing the
mark on this product, we are
confirming compliance to all relevant European safety,
health and environmental requirements which are
applicable in legislation for this product .
1-3
2.Quick operation guide
For detailed operating method read the corresponding content on the instruction manual.
Switch on the appliance
Open the door,press the On/Off button to switch on the appliance .
B.
Fill the detergent dispenser
Check the rinse aid level
Check the regeneration
salt level
Load the baskets
The detergent container is inside the door.
If the lid of the container is closed, press
the button (A) to open.
At the end of every wash cycle the lid is
always open and ready for the next time
the dishwasher is used.
Mechanical indicator B.
It is always advisable to use rinse aid that is specifically designed for dishwasher.
Check the rinse aid level through the indicator eye (B) which is located on the dispenser.
(On models with water softener system only.)
Electric indicator on control panel (if provided).
If there is no salt warning light in the control panel
(for some models), you can estimate when to fill the salt into
the softener by the number of cycles the dishwasher has run.
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.
Select a programme
Close the door, Press the Programme button until the selected programme lights up.
( See the section entitled Operation instruction )
Running the dishwasher
T urn on the water tap , Press the Start/Reset button, The machine will start working at once.
Changing the programme
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Press the Start/Reset Button for more than 3s to cancel the running programme.
3. Select a new programme.
4. Restart the dishwasher.
Add forgotten dishes in the
dishwasher.
1.Open the door a little to stop the machine.
2.After the spray arms stop working, you can open the door completely.
3.Add the forgotten dishes.
4.Close the door,the dishwasher will start running again after 10 seconds.
If the appliance is switched
off during a wash cycle.
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).
Switch off the appliance
When the working cycle has finished, the buzzer of the dishwasher will sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
Since the appliance is standing by, it will power off automaticly after 30 minutes without any operation.
Turn off the water tap,
unload the baskets
WARNING!
Open the door carefully.
Hot steam may escape
when the door is opened!
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will also dry better.Unload the appliance, starting from the lower basket.
2
3.Operation Instruction
IMPORTANT
To get the best performance from your dishwasher, read all operating instructions
before using it for the first time.
Control Panel
7
6
1
3
2
8
4
5
Dishwasher Features
Front view
Back View
6
1
2
7
8
3
4
5
9
1
2
3
Upper Basket
Inner pipe
Lower Basket
4
5
6
7
8
9
Salt Container
Dispenser
Cup Shelf
3
Spray arms
Filter assembly
Security Inlet pipe
10
10
Drain pipe
4.Prior using for the first time
Before using your dishwasher for the first time:
A. Set the water softener
B. Add 1.5Kg dishwasher salt and then full fill the salt container with water
C. Fill the rinse aid dispenser
D. Fill in detergent
A. Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which would have
a detrimental or adverse effect on the operation of the appliance.
The higher the content of these minerals and salts, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority
can advise you on the hardness of the water in your area.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed based on the hardness of
the water used. This is intended to optimise and customise the level o f salt consumption.
Please follow the steps below for adjustment in salt consumption.
1. Switch on the appliance;
2. Press the Program button for more than 5 seconds to start the water
softener set model within 60seconds after the appliance was
switched on;
3. Press the Program button to select the proper set according to
your local environment, the sets will change in the following
sequence: H3->H4->H5->H6->H1->H2;
4. Press the On/Off button or no operation for 5 seconds to end the set up model.
WATER HARDNESS
dH
fH
mmol/l
Clark
0~0.94
Selector Position
Salt co nsumption
(gram/cycle)
0~5
0~9
0~6
H1: P5 Light bright
0
6-11
10-20
7-14
1.0-2.0
H2: P4 Light bright
9
12-17
21-30
15-21
2.1-3.0
H3: P4 P5 Light bright
12
18-22
31-40
22-28
3.1-4.0
H4: P3 Light bright
20
23-34
41-60
29-42
4.1-6.0
H5: P3 P5 Light bright
30
35-55
61-98
43-69
6.1-9.8
H6: P3 P4 Light bright
60
Note:1
1 dH=1.25 Clarke=1.78 fH=0.178mmol/l
dH: German degree
fH:
French degree
Clark: British degree
Note:2
The manufactory setting: H3:P4 P5 Light bright (EN 50242)
Contact your local water board for information on the hardness of your water supply.
NOTE:
If your model does not have any water softener, you may skip this section.
WATER SOFTENER
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will
form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt container specifically designed to eliminate
lime and minerals from the water.
4
B. Loading the Salt Into the Softener
Always use the salt intended for use with dishwasher.
The salt container is located beneath the lower basket and should be filled as explained
in the following:
Attention!
Only use salt specifically designed for the use in dishwashers! Every other type of
salt not specifically designed for the use in a dishwasher, especially table salt, will
damage the water softener. In case of damages caused by the use of unsuitable
salt the manufacturer does not give any warranty nor is liable for any damages caused.
Only fill with salt just before starting one of the complete washing programs.
This will prevent any grains of salt or salty water, which may have been spilled,
remaining on the bottom of the machine for any period of time, which may cause
corrosion.
A After the lower basket has been removed, unscrew and remove the cap from the salt container.
1
B Place the end of the funnel (supplied) into the hole and introduce about 1.5kg of dishwasher salt.
2
C Full fill the salt container with water,It is normal for a small amount of water to come out of the
salt container.
D After filling the container , screw the cap tightly back clockwise.
E The salt warning light will stop being after the salt container has been filled with salt.
F Immediately after filling the salt into the salt container, a washing program should be started (We suggest to use a short
program). Otherwise the filter system, pump or other important parts of the machine may be damaged
by salty water. This is out of warranty.
NOTE:
1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how well the salt dissolves, the salt warning light may still be on even though the
salt container is filled.
If there is no salt warning light in the control panel (for some Models),you can estimate when to fill
the salt into the softener by the cycles that the dishwasher has run.
2. If there are spills of the salt, a soak or a rapid program should be run to remove the excessive salt.
5
C. LOADING THE DETERGENT
The detergent
IMPORTANT
It is essential to use a detergent that is specifically designed for dishwashers either in powder, liquid or tablet form.
FINISH gives very good results and can be easily obtained.Unsuitable detergents (like those for washing up by hand)
do not contain the proper ingredients for use in a dishwasher and stop the dishwasher from working correctly.
Filling the detergent container
The detergent container is inside the door (fig. A 2 ). If the lid of the container is closed, press the button (A) to open.
At the end of every wash cycle the lid is always open and ready for the next time the dishwasher is used.
The amount of detergent to be used varies according to how dirty the dishes are and on the type of dishes to be washed.
We advise using 20/30 g of detergent in the wash section of detergent compartment (B).
After pouring the detergent into the container,close the lid, firstly pushing (1) and then pressing on it (2) until you hear the click.
Since not all detergents are the same the instructions on the boxes of detergent can vary. We should just like to remind users
that too little detergent does not clean the dishes properly whilst too much detergent will not produce better results and is
also a waste.
6
7
LOADING THE RINSE AID
The rinse aid
The rinse aid, which is automatically released during the last rinsing cycle, helps the dishes to dry quickly and
prevents spots and stains forming.
Filling the rinse aid container
The rinse aid container can be found to the left of the detergent container (fig. A "3").To open the lid, push the
reference mark and, in the same time, pull the tab of opening.It is always advisable to use rinse aid that is specifically
designed for dishwasher.Check the rinse aid level through the indicator eye (C) which is located on the dispenser.
Regulating the rinse aid from 1 to 6
The regulator (D) is placed under the lid and can be turned using a coin.The recommended position is 4.The
limestone content of the water considerably affects the formation of limescale and the drying performance.
It is therefore important to regulate the quantity of rinse aid to achieve good washing results.If, after the wash,
streaks occur on the dishes, decrease the amount by one position. If whitish spots occur, increase the amount
by one position.
8
5.Loading the Dishwasher Baskets
Recommendation
Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind to dishes'. If necessary, seek further
information from the detergent manufacturers.
For particular items, select a program with as low a temperature as possible.
To prevent damage, do not take glass and cutlery out of the dishwasher immediately
after the programme has ended.
For washing in the dishwasher the following cutlery/dishes
Are not suitable
Are of limited suitability
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that are not
temperature resistant
Bonded cutlery items or dishes
Pewter or copper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
Some types of glasses can become
dull after a large number of washes
Silver and aluminum parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
Attention before or after loading the Dishwasher Baskets
(For best performance of the dishwasher, follow these loading guidelines.
Features and appearance of baskets and cutlery baskets may vary from your model.)
Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans.
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots/pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are placed in the way that the spray arms can rotate freely during washing.
NOTE: Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
Load hollow items such as cups, glasses, pans etc. With the opening facing downwards so that
water cannot collect in the container or a deep base.
Dishes and items of cutlery must not lie inside one another, or cover each other.
To avoid damage to glasses, they must not touch.
Load large items which are most difficult to clean into the lower basket.
The upper basket is designed to hold more delicate and lighter dishware such as glasses, coffee
and tea cups
Long bladed knives stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knives must be positioned
horizontally in the upper basket.
Please do not overload your dishwasher. This is important for good results and for
reasonable consumption of energy.
Removing the Dishes
To prevent water dripping from the upper basket into the lower basket, we recommend that you
empty the lower basket first and then the upper basket.
9
The Method Loading Normal Dishware
Loading the Lower Basket
Loading the Upper Basket
The upper basket is designed to hold more delicate
and lighter dishware such as glasses, coffee and
tea cups and saucers, as well as plates, small bowls
and shallow pans (as long as they are not too dirty).
Position the dishes and cookware so that they will
not get moved by the spray of water.
We suggest that you place large items and the most
difficult to clean items are to be placed into the lower
basket: such as pots, pans, lids, serving dishes and
bowls, as shown in the figure below. It is preferable to
place serving dishes and lids on the side of the racks
in order to avoid blocking the rotation of the top spray
arm.
IN
IN
Please be reminded that:
Pots, serving bowls, etc, must always be placed top down.
Deep pots should be slanted to allow water to flow out.
The Bottom Basket features folding spikes so that larger or more pots and pans can be loaded.
Adjusting the Upper Basket
Folding back the cup shelives
The height of the upper basket can be adjusted in order to
create more space for large utensils both for the upper
/lower basket. The height of the upper basket can be
adjusted by placing the wheels on different height of the
rails. Long items, serving cutlery, salad servers and knives
should be placed on the shelf so that they do not obstruct
the rotation of the spray arms..
For better stacking of pots and pans,
the spikes can be folded down as
show in the picture right.
Folding Spikes of Lower Basket
For better stacking of pots and pans,
the spikes can be folded down as
show in the picture right.
Cutlery Basket
Cutlery should be placed in the cutlery basket with the handles at the bottom. If the rack has side baskets, the
spoons should be loaded separately into the appropriate slots, especially long utensils should be placed in the
horizontal position at the front of the upper basket as shown in the picture.
WARNING!
Do not let any item extend through the bottom.
Always load sharp utensils with the sharp
point down!
For personal safety and a top quality cleaning, place the silverware in the basket
making sure that:
They do not nest together.
Silverware is placed with the handles-down.
But place knives and other potentially dangerous utensils are placed handles-up.
10
6.Starting a washing program
Wash Cycle Table
NOTE: (
) Means: need to fill rinse into the Rinse-Aid Dispenser.
Cycle Selection
Information
Program
Description
of Cycle
P1
Intensive
For heaviest soiled crockery,
and normally soiled pots
pans dishes etc with dried
on soiling.
Prewash(50 )
Wash (60 )
Rinse
Rinse
Rinse(69 )
Drying
P2
Normal
For normally soiled loads,
such as pots, plates,glasses
and lightly soiled pans.
Prewash(45 )
Wash (55 )
Rinse
Rinse(66 )
Drying
This is standard programme, it is
suitable to clean normally soiled
tableware and it is the most efficient
programme in terms of its combined
energy and water consumption for
that type of tableware.
Prewash
Wash (45 )
Rinse(62 )
Drying
P4
Rapid
A shorter wash for lightly
soiled loads and quick wash.
Wash (55 )
Rinse(55 )
Rinse(55 )
P5
Soak
To rinse dishes that you plan to
wash later that day.
Prewash
*EN 5 0242
Detergent Running
pre/main time(min)
3 /22
1 piece
Energy
(Kwh)
165
1.4
16.5
3 /22
1 piece
175
1.1
13
3 /22
1 piece
205
0.74
9
30
0.7
10
15
0.02
3.5
20
NOTE:
*EN 50242 : This program is the test cycle. The information for comparability test
in accordance with EN 50242, as follows:
Capacity: 10 setting
Position Upper basket: upper wheels on rails
Rinse aid setting: 6
PI:0.45W; Po:0.30W.
Left-on mode duration 30Min.
Turning On the Appliance
Starting a cycle wash
1
2
3
4
5
Draw out the lower and upper basket, load the dishes and push them back.
It is commended to load the lower basket first, then the upper one (see the section entitled
Loading the Dishwasher ).
Pour in the detergent (see the section entitled Salt, Detergent and Rinse Aid ).
Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification
of the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
Close the door, press the Power button, to switch on the machine.
Press the program button, the wash program will be changed as follows direction:
P3
P4
P5
P1
P2
If a program is selected, the response indicator will light. Then press the Start/Reset button, the
dishwasher begins to start.
11
Water Rinse
(L)
Aid
NOTE:
[ P1 - Intensive, P2 - Normal, P3 - Eco, P4 - Rapid, P5 - Soak ]
Change the Programme
Premise:
A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
detergent may have already been released, and the appliance may have already drained the wash water.
If this is the case, the detergent dispenser must be refilled (see the section entitled " Loading the
Detergent " ).
2 Press the Start/Reset button for more than 3s, the machine will be instand by state. then you can change the
program to the desired cycle setting (see the section entitled " Starting a wash cycle. . ." ).
1
NOTE:
If you open the door during a wash cycle , the machine will pause. The program light will
stop blinking and the buzzer will moo every minute untill you close the door . After
you close the door ,the machine will keep on working after 10 seconds.
If your model has broken remember function, the machine will go on to finish the selected
program after the power cut.
Forgot to Add a Dish?
A forgotten dish can be added any time before the detergent cup opens.
1 Open the door a little.
4
Close the door.
2 After the spray arms stop working, you can open the door
5
The dishwasher will run after 10 seconds.
completely.
3
Add forgotten dishes.
At the End of the Wash Cycle
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
1.Switch off the dishwasher by pressing the On/Off Button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
WARNING!
It is dangerous to open the door when washing,
because the hot water may scald you.
12
7.Maintenance and Cleaning
Filtering System
The filter prevents larger remnants of food or other objects from getting inside the pump.
The residues may block the filter, in this case they must be removed.
The filter system consists of a coarse filter,a flat (Main filter)
And a microfilter(Fine filter).
Main filter
2
1
Food and soil particles trapped in this filter are pulverized by a
special jet on the lower spray arm and washed down to drain.
1
Coarse filter
2
Larger items, such as pieces of bones or glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by the filter, gently squeeze the tap on the top of this
filter and lift out.
3
Fine filter
3
This filter holds soil and food residues in the sump area and
prevents it from being deposited on the dishes during wash cycle.
Filter assembly
The filter efficiently removes food particles from the wash water, allowing it to be recycled during the cycle.
For best performance and results, the filter must be cleaned regularly. For this reason, it is a good idea to
remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter and
cup under running water. To remove the filter device, pull the cup handle in the upward direction.
WARNING!
n
n The dishwasher must never be used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
1
Open
Step 1
Turn the filter in anti-clockwise direction,
2
Step 2 lift the filter assy up
NOTE:
When following this procedure from step1 to step 2, the filter system will be removed;
when following it from Step 2 to Step 1, the filter system will be installed.
13
Remarks:
- Inspect the filters for blocking after every time the dishwasher has been used.
- By unscrewing the coarse filter, you can remove the filter system. Remove any food remnants and
clean the filters under running water.
NOTE: The entire filter assembly should be cleaned once a week.
Cleaning the Filter
To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures
on the last page and reinsert the entire assembly in the dishwasher, positioning it in its seat and pressing downwards.
WARNING!
When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted and the performance of the dishwasher could be decreased.
Caring for the Dishwasher
The control panel can be cleaned by using a lightly dampened cloth.
After cleaning, make sure to dry it thoroughly.
For the exterior, use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Cleaning the Door
To clean the edge around the door, you should use only a soft warm, damp cloth.
To avoid penetration of water into the door lock and electrical components, do not
use a spray cleaner of any kind.
n
WARNING!
Never use a spray cleaner to clean the door panel as it may damage the door lock
n and electrical components.
Abrasive agents or some paper towels should not be used because of the risk of
scratching or leaving spots on the stainless steel surface.
Protect Against Freezing
please take frost protection measures on the dishwasher in winter. Every time after washing cycles,
please operate as follows
1.Cut off the electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)
4.Reconnect the water inlet pipe to the water valve.
5.Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.
NOTE:
If your dishwasher cannot work because of the ice,
please contact professional service persons.
Cleaning the Spray Arms
It is necessary to clean the spray arms regularly for hard
water chemicals will clog the spray arm jets and bearings.
To remove the upper spray arm, hold the nut, rotate the arm
clockwise to remove it.
To remove the lower spray arm, pull out the spray arm upward.
Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.
14
Open
How to Keep Your Dishwasher in Shape
After Every Wash
When not in Use for a LongTime
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odours are not trapped inside.
It is recommend that you run a wash cycle with the
dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
seals to last longer and prevent odours from forming
within the appliance.
Remove the Plug
Before cleaning or performing maintenance, always
remove the plug from the socket.
Moving the Appliance
No Solvents or Abrasive Cleaning
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Only use a cloth with warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water an a little
vinegar, or a cleaning product made specifically for
dishwashers.
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
Seals
One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
8.Installation instruction
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can
be positioned either to the right or the left sides to facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned for levelling, the height of the dishwasher
may be altered via adjustment of the screwing level of the feet.
About Power Connection
WARNING!
n
n
n
For personal safety:
Do not use an extension cord or an adapter plug
with this appliance.
Do not, under any circumstances, cut or remove the
earthing
Connection from the power cord.
Electrical Requirements
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and provide separate circuit serving
only this appliance.
Electrical Connection
Insure proper ground
exists before use
Ensure the voltage and frequency of the power being corresponds to
those on the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug , replace the socket, rather than using a adaptors or the like as
they could cause overheating and burns.
15
How to connect the safety supply hose
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below the
minimum consult our Service Department for advice.
1. Pull The safety supply hoses completely out from storage compartment located at rear
of dishwasher.
2.Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.
3.Turn water fully on before starting the dishwasher.
About the safety supply hose
The safety supply hose consists of the double walls. The hose's system guarantees its intervention by blocking the flow
of water in case of the supply hose breaking and when the air space between the supply hose itself and the outer
corrugated hose is full of water.
WARNING!
A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has
one, it is recommended thet the hose be disconnected and the hole plugged.
How to disconnect the safety supply hose
1. Turn off the water.
2.Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
room, from severe splashing.
3.Unscrew The safety supply hose from the faucet..
COLD WATER CONNECTION
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the
water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and
damage the appliance.
Drain hose Connection
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the hose must be less than 1000mm.
PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, B
Front
Drain pipe
A
MAX 1000mm
NOTE
The top of the hose
must be less than
1000mm.
Counter
B
40mm
How to Drain Excess Water From Hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water drain hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
Syphon Connection
The waste connection must be at a height less than 1000 mm (maximum) from the bottom of the dish.
The water drain hose should be fixed .
Start of Dishwasher
The following things should be checked before starting the dishwasher.
1 The dishwasher is level and fixed properly
2 The inlet valve is open
3 Fill hose connections are fully tightened and not leaking
4 The wires are tightly connected
5 The power is switched on
6 The inlet and drain hoses are knotted
7 All packing materials and printings should be taken out from the dishwasher
Attention:
After installation, please make sure to keep this manual.
The content of this manual is very helpful to the users.
17
9.Troubleshooting Tips
Before Calling for Service
Review the charts on the following pages may save you from calling for service.
Problem
Possible CausesWhat to Do
Dishwasher doesn't Fuse blown, or the
circuit breaker acted
start
Technical
problems
water not pumped
from dishwasher
Suds in the tub
Stained tub interior
White film on
General inside surface
problems
There are rust
stains on cutlery
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Water pressure is low
Check that the water supply is connected properly and
the water is turned on.
Door of dishwasher
not properly closed.
Make sure to close the door properly and latch it.
Kink in drain hose
Check drain hose.
Filter clogged
Check the coarse filter
(see section titled " Cleaning The Filter ")
Kitchen sink clogged
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.
Improper detergent
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 1 gallon of cold water to the tub. Close and latch the
dishwasher, then select any cycle. Dishwasher will drain
out the water at the first step.Open the door after draining
is stop and check if the suds is disappeared.
Repeat if necessary.
Spilled rinse-aid
Always wipe up rinse-aid spills immediately.
Detergent with
colourant was used
Make sure that the detergent is the one without
colourant.
Hard water minerals
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
The affected items are
not corrosion resistant.
A programme was not
Always run the quick wash programme .
run after dishwasher
without any crockery in the dishwasher and
salt was added.
without selecting the Turbo function (if present),
Traces of salt have
after adding dishwasher salt.
gotten into the wash cycle.
Noise
The lid of the softer
is loose
Check the lid .Ensure the fix is fine.
Knocking noise
in the wash cabinet
A spray arm is
knocking against
an item in a basket
Interrupt the programme, and rearrange the items
which are obstructing the spray arm.
Rattling noise
in the wash cabinet
Items of crockery
are loose in the
wash cabinet
Interrupt the programme,
and rearrange the items of crockery.
Knocking noise
in the water pipes
This may be caused
by on-site installation
or the cross-section of
the piping.
This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
18
Problem
Possible Causes
The dishes
are not clean
The dishes were not
loaded correctly.
See notes in " Loading the Dishwasher Baskets ".
The programme was
not powerful enough.
Select a more intensive programme.
See" Wash Cycle Table ".
Not enough detergent
was dispensed.
Use more detergent, or change your detergent.
Items are blocking
the path of spray arms.
Rearrange the items so that the spray can rotate freely.
The filter combination
in the base of wash
cabinet is not clean or
is not correctly fitted.
This may cause
the spray arm jets
to get blocked.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets. See "Cleaning the Spray
Arms".
Cloudiness
on glassware
Combination of soft
water and too much
detergent.
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Black or gray
marks on dishes
Aluminum utensils
have rubbed against
dishes.
Use a mild abrasive cleaner to eliminate those marks.
Detergent left in
dispenser cups
The dishes
are not drying
Dishes block
detergent cups.
Re-loading the dishes properly.
Improper loading
Load the dishwasher as suggested in the directions.
Too little rinse-aid
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Dishes are removed
too soon
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
Wrong program
has been selected
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose
a program with a long washing time.
Use of cutlery with
a low-quality coating
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
Unsatis
-factory
washing
result
Unsatis
-factory
drying
result
What to Do
Error Codes
When some malfunctions come on, the appliance will display error codes to warn you:
Codes
Meanings
Possible Causes
P5 indicator fleets frequently
Longer inlet time.
Faucets is not opened, or water intake is
restricted,or water pressure is too low.
P3 indicator fleets frequently
Overflow.
Some element of dishwasher leaks.
P4 and P5 indicators
fleet frequently
Not reaching the required temperature .
Malfunction of the heating element.
P2, P3 and P5 indicator
fleets frequently
Communication Abnormal.
Detect abnormal data over 20s, indicator fleets.
Without treatment, it returns to normal after the
signal recovery.
WARNING!
n
n If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.
19
Technical Information
448
845
11 7 5
Height :
Width :
Depth :
845mm
448m m
6 05 mm (with the door closed)
Water pressure:
Power supply:
Capacity:
0.04-1.0MPa
see rating label
10 place settings
20
Technical Data Sheet
Sheet of household dishwasher according to EU Directive 1059/2010:
Manufacturer
CANDY
Type / Description
CDP 2L1049W- 80
Standard place settings
10
Energy efficiency class
1
A++
Annual energy consumption
2
211 kWh
Energy consumption of the standard cleaning cycle
0.74 kWh
Power consumption of off-mode
0.30 W
Power consumption of left-on mode
0.45 W
Annual water consumption
3
2520 liter
Drying efficiency class
4
A
Standard cleaning cycle
5
ECO 45
Program duration of the standard cleaning cycle
205 min
Noise level
49 dB(A) re 1 pW
Mounting
Free standing
Could be built-in
Yes
Height
84.5 cm
Width
44.8 cm
Depth (with connectors)
60.5 cm
Power consumption
1930 W
Rated voltage / frequency
230 V~ 50 Hz
Water pressure (flow pressure)
0.4-10 bar = 0.04-1 MPa
NOTE
1 A + + + (highest efficiency) to D (lowest efficiency)
2 Energy consumption
211 kWh per year, based on 280 standard cleaning cycles using cold water fill and
the consumption of the low power modes. Actual energy consumption will depend on how the appliance is used.
3 Water consumption
2520 litres per year, based on 280 standard cleaning cycles. Actual water consumption
will depend on how the appliance is used.
4 A (highest efficiency) to G (lowest efficiency)
5 This program is suitable for cleaning soiled normally soiled tableware and that it is the
most efficient programme in terms of its combined energy and water consumption for
that type of tableware.
The above values have been measured in accordance with standards under specified operating conditions.
Results may vary greatly according to quantity and pollution of the dishes, water hardness,
amount of detergent, etc.
The manual is based on the European Union's standards and rules.
21
3
2 3
6
3
7
1
1
5
3
10
9
3
2
3
Cutterly basket
9
8
2.Lower basket:
4
IN
1.Upper basket:
8
1
2
7
3
1
1
Shelf
Oval platter
10
Soup plates
9
Dinner plates
8
Dessert dishes
7
Large serving bowl
6
Medium serving bowl
5
Small serving bowl
4
Glasses
3
Saucers
2
1
Cups
Loading the baskets according to En50242:
IN
6
2
3
3
1
1
1
4
7
4
4
4
4
4
1
1
1
8 Gravy ladles
7 Serving forks
6 Serving spoons
5 Dessert spoons
IN
4
4
4
4
1
8
1
Information for comparability tests in accordance
with EN 50242
Capacity: 10 place settings
Position of the upper basket: lower position
Programme: ECO
Rinse aid setting: 6
Softener setting: H3
4 Teaspoons
3 Knives
2 Forks
1 Soup spoons
1
1
3.Cutterly basket:
Note: Please place the light flat wares on the shelf. The
total weight is less than 1.5kg.
Shelf
Download PDF
Similar pages