7LIECH-SSF-G(Wal-Mart) - Glacial Water Coolers Glacial Water

Stainless Steel
Hot and Ice Cold
Water Cooler
Model No.: 7LIECH-SSF-G
USER MANUAL
User of mineral water
please read descaling
instructions on the
page 13
SAVE THIS MANUAL
FOR FUTURE USE
For service call: 1-844-452-2425
or send E-mail to: help@glacialhome.com
7LIECH-SSF-G © 2016 Electrotemp Technologies Inc.
PN: 5M010153X004(E+F)
Model # 7LIECH-SSF-G: Page 2
SAFETY PRECAUTIONS
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and your appliance. Always read and follow all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER”or “WARNING”
These words mean:
DANGER
You can be killed or seriously injured if you don′t immediately
the follow instructions.
WARNING
You can be killed or seriously injured if you don′t follow the
instructions.
All safety instructions will inform you what the potential hazard is, how to reduce the chance of injury, and what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your water cooler, follow these basic precautions:
■ Plug it into a grounded 3-prong outlet.
■ Do not remove the ground prong.
■ Do not use an adapter.
■ Disconnect the power before servicing.
■ Replace all the parts and the panels before operating.
■ Do not use an extension cord.
■ Two or more people should move and install the water cooler
and the bottles.
■ Never allow children to dispense hot water without proper and direct supervision. Unplug unit to prevent
unsupervised use by children.
SAVE THESE INSTRUCTIONS
When operating this dispenser, please observe the following:
• Prior to use, this dispenser must be properly assembled and installed in accordance with
this manual.
• This dispenser is intended only for water dispensing. Do NOT use other liquids. Do NOT
use for other purposes. Never use other liquids in the dispenser other than known and
microbiologically safe bottled water. Warranty is void if used with any other liquids, such
as coffee, tea, juices, beer or wine.
Location Requirements:
• Install in the area where it is protected from the elements including direct sun.
• Install and use only on a hard, flat and level surface.
• Do NOT place the dispenser inside an enclosed space or cabinet.
• Position the dispenser no closer than 4 inches from the wall with at least 4 inches clearance on the sides to permit free airflow.
• Service should only be performed by a certified technician. Please contact us at 1-844-452-2425 for assistance.
• “Opening any panel of this machine will void warranty. Store returns will
not be accepted. Call 1-844-452-2425 for service.”
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 3
SAFETY PRECAUTIONS ---Electrical Requirements
WARNING
Electrical shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
A 120 volt, 60 Hz., AC only, 15 amp, fused electrical supply is required. A time-delay fuse or
circuit breaker is recommended.
If codes permit and a separate ground wire is used, it is recommended that a qualified
electrician determine that the ground path is adequate.
Check with a qualified electrician if you are not sure if the water cooler is properly grounded.
PRODUCT FEATURES
Congratulations! You have chosen an Advanced Technology State of the Art Water
Cooler.
The refrigeration system on this cooler cools the cold water by internal evaporator of commercial design flat forms the ice around it. This feature is called an "Ice Bank". It allows for ice
cold water and keeps the water temperature consistently cold, however a Longer time in
forming the Ice Bank is required. Since ice is an insulator, the more ice is built up, the slower
next layer is made.
WHEN UNIT IS PLUGGED IN FOR THE FIRST TIME WAIT FOR UP TO 1 HOUR FOR
WATER TEMPERATURES TO REACH COLD TEMPERATURES. COMPRESSOR WILL
CONTINUE TO WORK UP TO 2.5 HOURS TO BUILD UP ICE BANK.
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 4
TABLE OF CONTENTS
Safety Precautions ...............................................................
2
Safety Precautions-Electrical Requirements ........................
3
Product Features
................................................................. 3
Key Information for Future Use ............................................ 4
Specifications ......................................................................
5
Parts & Features ..................................................................
5
Unpacking and Assembly ....................................................
6
Installation ............................................................................
6
Cleaning Prior to Initial Use
...............................................
8
Operation .............................................................................
9
Proper Care & Descaling .......................................................11
Troubleshooting .................................................................. 13
Limited Warranty .................................................................. 15
KEY INFORMATION FOR FUTURE USE
Please register your dispenser immediately at
www.electrotemp.com
For future support, please record your serial number (located on
label on back of dispenser) and date purchased. Staple your
receipt to manual.
You will need this information to obtain warranty service.
Product
Stainless Steel Hot and Ice Cold Water Cooler
Model Number
7LIECH-SSF-G
Serial ID Number
Date of Purchase
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 5
SPECIFICATIONS
Power Supply
AC 120V / 60Hz / 4.5 Amp
Refrigerant Type
R-134A
Cold Water Power
100 Watts
Cold Capacity / Hour
5 L / 1.32 Gallon
Cold Temp Rang
3°C - 10°C / 37.4°F - 50°F
Hot Water Power
425 Watts
Hot Capacity / Hour
4 L / 1.05 Gallon
Hot Temp Range
80°C - 92°C / 176°F - 197.6°F
Dimensions
27.5 W × 28.6 D × 91.3 H (cm)
10.8 W × 11.3 D × 35.9 H (inch)
12.25 Kg / 27 Ibs
Net Weight
PARTS & FEATURES
Bottle Probe
1
Hot Water Control
2
Child Safety Latch
3
Cold Water Control
4
Hot Water Tap
5
Cold Water Tap
6
Drip Tray
7
Energy Saving Switch
8
Cooling Thermostat
9
Carry Handle
10
Power Cord
11
Drain Plug
12
LED night light
13
Back
Front
1
4
2
8
3
9
11
6
5
13
10
12
7
The wall mount strap
and the collar for plain,
capped bottles are
not shown.
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 6
UNPACKING AND ASSEMBLY
Remove the dispenser from packaging:
TOP
TO OPEN:
TOP
TOP
TOP
1. Lay dispenser on its side.
2. Open bottom flaps of the cardboard box.
3. Stand cooler up with flaps unfolded.
4. Pull box straight up.
5. Unpack the drip tray and insert it into the dispenser.
(See illustration )
6. Keep original packing for the duration of warranty.
INSTALLATION
4in. Min
1. Locate the dispenser on a hard and level surface in a cool
shaded location near a grounded wall outlet.
2. Position dispenser so that the back is at least 4 inches from
the wall and there are at least 4 inches of clearance on both
sides.
3. To minimize vibration and noise, make sure that all 4 feet are
adjusted to keep dispenser levelled.
4 adjustable feet
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 7
4. Install the Wall Mount Strap to prevent accidental tip
over:
• Unclip the strap from the back of dispenser.
• Mount the strap 25 inches up from the floor directly to
the wall stud with a screw (see Illustration A).
If the stud is not available, insert and turn the anchor
directly into the sheet rock using a star shaped
screwdriver (DO NOT drill a hole into the sheet rock
first when using this anchor). Secure the strap by
installing a screw through the washer, then the eyelet
into the strap, and into the wall mounted anchor (see
Illustration B).
• Position the cooler in place.
• Clip the strap onto the back of the cooler to either the
right or left side (see Illustration C).
• Adjust the length of the strap.
Note: The dispenser can be positioned in a corner but it
still requires the Wall Mount Strap to be installed.
Adjust length of the wall strap accordingly.
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 8
CLEANING PRIOR TO INITIAL USE
To remove any odors or dust that may have accumulated during shipment, you may want
to clean the dispenser prior to first use.
DO NOT PLUG THE COOLER INTO AN ELECTRICAL POWER OUTLET AT THIS TIME.
Time Required for Set Up: 40 minutes.
1. Remove the bottle receptacle by turning it counter clockwise and
pulling up.
2. Remove the plastic baffle from inside the reservoir. Clean with
warm soapy water, rinse.
3. Fill the reservoir with a mixture of 1 gallon tap water and 1
teaspoon or unscented bleach (5.25% sodium hypochlorite).
4. Let sit for 30 minutes.
5. Dispense 1 cup of mixture through both faucets to clean out water
ways.
To Remove Bottle
Receptacle
6. Place a 2 gallon or larger bucket under the drain plug in
the rear of the dispenser. Remove drain cap and drain
plug.
Reminder - Place the drain cap, drain plug and screw in
a safe location so that they will not be lost.
7. Once unit has completed draining, empty the bucket
and return it to under the drain cap.
8. Replace drain cap and drain plug.
9. Wipe the inside of the reservoir with a soft cloth.
10. Fill the reservoir with 1 gallon of tap water.
11. Dispense 1 cup of water through both faucets to rinse
out water ways.
12. Remove the drain cap and the drain plug.
Reminder - Place the drain cap, drain plug and screw in a safe location so that they will
not be lost.
13. Remove the water from the reservoirs by dispensing it from both taps into a pitcher.
14. Replace all parts. Reminder - Don’t forget the drain plug and drain cap.
15. Complete the installation and follow the operation instructions indicated in this manual.
If your water has an off-taste, do not return the dispenser to store. Call 1-844-452-2425 for
assistance.
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 9
OPERATION
IMPORTANT
This unit is intended for water dispensing only. Do NOT use other liquids. Do NOT use
for other purposes. Warranty is void if used with any other liquids such as coffee, tea,
juices, beer or wine.
This dispenser has been designed to use water bottles with a 3 or 5 gallon capacity. Do
NOT use alternative bottles.
Initial Set Up
Note: To avoid damage to the compressor, allow the unit to sit upright for at least 4 hours prior
to operation.
1. Remove the tamper seal from the bottle cap. Do NOT remove the plastic cap.
2. Clean the bottle cap and neck using a soft cloth and warm soapy water, then rinse afterwards.
3. Lift the bottle and insert onto the probe. Apply slight pressure until the plug inside the cap
pushes in and the bottle is seated. Water will begin to flow into the reservoirs, causing air
bubbles to form in the bottle.
WARNING
Electrical shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
4. Plug the cord into a properly grounded wall outlet.
5. Turn energy saving switch on back of dispenser to ON. This switch controls the heating of
water. If you do not want hot water, turn this switch OFF.
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 10
Dispensing Cold Water
Note: After setup, it will take up to 1 hour to get the water to its cold temperature. Compressor
will run continuously for 2.5 hours. It will work to build up ice bank, this is normal.
1. Position the bottle, glass, pitcher, or cooking pot securely below the cold water tap.
- The right triangle below the cold water control indicates the location of the cold water
tap(See Parts & Features NO. 6).
- The circular shapes in the drip plate help align the flow of water. This unit dispenses water
at a fast rate. To avoid splashes, hold the cup as close to the tap as possible.
2. Press the cold water control downward to start dispensing water.
3. Release the cold water control once the desired fill level is achieved
Dispensing Hot Water
1. Hot water available 15~20 minutes after set up.
2. Red arrow and target holes in the grill indicate positioning of you container for dispensing
hot water.
3. Hold your container close to dispensing nozzle to avoid splashes.
4. To activate hot water dispensing nozzle push red lock inwards and hot button downwards.
5. To stop dispensing hot water release the button.
Replacing an Empty Bottle
Note: Replace the bottle as soon as you notice that it is empty.
1. Lift the bottle straight up to disengage it from the bottle probe.
2. Remove the tamper seal from the top of bottle cap of the fresh bottle. Do NOT remove the
plastic cap.
3. Lift the bottle and insert it onto the probe. Apply slight pressure until the plug inside the
cap pushes in and the bottle is seated. Water will begin to flow into the reservoirs, causing
air bubbles in the bottle
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 11
PROPER CARE & DESCALING
General Cleaning
Perform: As needed
Time Required: 5 minutes.
Note: Do NOT use abrasive materials or chemical cleaners.
They may scratch surfaces and contaminate drinking water. For cleaning hard spots suggest
rubbing with toothpaste.
1. Clean the cabinet surfaces using a soft cloth and warm soapy water, then rinse.
2. Wipe dust at the back of dispenser to improve efficiency.
3. Remove the drip tray assembly by pulling it forward. Remove the cover. Place the tray and
cover in the dishwasher or wipe the parts clean using a soft cloth and warm soapy water.
4. Reattach drip tray assembly.
How to restore shine of stainless steel.
- Clean with cloth soaked in the dishwashing solution.
- Hard to remove spots can be rubbed away using stainless steel wool. Rub in horizontal
direction.
Then clean with cloth soaked in the dishwashing solution.
- Wipe dry with clean cloth.
- Apply a little bit of mineral oil ( unscented baby oil) and rub it in evenly.
Cleaning Cold Reservoir and Water Lines
Perform: Every 3 months or whenever an off-taste occurs.
Time Required: 15 minutes.
Note: Best to do prior to loading a fresh bottle.
1.
2.
3.
4.
Turn energy saving switch OFF.
Unplug the power cord from the wall outlet.
Remove the water bottle.
Unclip Wall Mount Strap from back of dispenser and
turn dispenser around so backside is facing away from
the wall.
5. Place a 2 gallon or larger bucket under the drain plug in
the rear of the dispenser.
Remove the drain cap and the silicon plug. Cold water
will immediately flow into the bucket. After several
seconds, hot water will be dispensed.
Reminder - Place the drain cap screw and in a safe location so that they will not be lost.
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 12
6.
Once unit has completed draining replace drain cap and drain plug.
7.
Remove remaining water from cold reservoir by dispensing from both taps into a pitcher.
8.
Remove bottle receptacle or collar by turning it counter clockwise and pulling up. Store in
a safe place.
9.
Remove plastic baffle from inside reservoir.
10. Clean bottle receptacle and baffle with a soft cloth using a mixture of one gallon tap water
and 1 tablespoons unscented household bleach, then rinse.
11. Wipe inside of reservoir and area around both taps with a soft cloth using the mixture of
one gallon tap water and 1 tablespoon unscented household bleach(i.e. 5.25% sodium
bypochlorite).
12. Pour the one gallon tap water and 1 tablespoon unscented household bleach mixture into
the reservoir.
13. Dispense 1 cup of mixture through both faucets to clean out water ways.
14. Place a 2 gallon or larger bucket under the drain plug in the rear of the dispenser.
Remove drain cap and silicon plug to drain.
Reminder - Place drain cap and drain plug in a safe
location so they are not lost.
15. Remove the cleaning mixture from reservoir by
dispensing it from both taps into a pitcher.
16. Replace drain cap and drain plug.
17. Rinse system by repeating steps 12 – 15 above, but
this time using 1 gallon of tap water.
18. Remove remaining water from reservoir by dispensing
from both taps into a pitcher.
19. Replace all parts including silicon plug, drain cap,
baffle and probe assembly.
20. Install a fresh bottle of water after cleaning
bottle cap and neck area.
21. Repeat rinsing cycle if chlorine taste persist.
WARNING
22. Plug power cord into grounded wall outlet.
23. Turn energy saving switch ON.
Electrical shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 13
Descaling
If you use mineral water you will need to descale your hot water tank.
Heated mineral water will cause minerals to fall out. Eventually they will plug up your waterways, resulting in a gradual slowdown of the flow rate, leaking faucets, and other problems.
Descaling Solutions
Cooking vinegar is proven to remove calcium deposits efficiently.
Depending on the frequency of decalcification treatments, please use the following proportions of White
Vinegar.
- For descaling once every 3 months, use 2 cups (500 ml) of white vinegar with 2.5 liters of hot water.
- For descaling once every 6 months, use a mixture of 6 cups of white vinegar with 2 liters of hot water.
- For descaling once every year, use 12 cups of white vinegar and 1 liter of hot water.
- For descaling less frequently than once a year, use undiluted white vinegar.
Descaling Procedure
1. Fill a bucket or empty 5-gallon water bottle with the vinegar solution of your choice. For proportions,
refer to the instructions above. Choose quantity in accordance with the frequency of your treatments.
2. Attach or insert the probe to the bucket/bottle.
3. Place the bucket/bottle into the cooler and close the door. The water will be pumped up into the
holding tanks.
4. Plug in the cooler and turn on the hot switch located at the back of the cooler. Do not turn on the
cold-water switch.
5. Wait for 1 hour.
6. Unplug the cooler from the wall
7. Using rear drain plug, drain the water from the cooler into a bucket and discard the water.
A. Locate the white plastic cap at the back of the cooler.
B. Remove the screw.
C. Remove the clear silicone drain plug and allow water to drain out.
D. Reattach the drain plug and plastic cap before proceeding.
8. Fill the bucket/bottle with tap water and place into the machine.
9. Plug the cooler back into the wall, close the door and wait for 10 minutes.
10. Dispense water from both cold and hot faucets until smell from cleaning substances disappears.
11. Open drain plug and cap once again and drain all tap water.
12. Replace the drain plug and cap.
13. Place a fresh bottle of water into the machine and operate as usual.
14. This procedure must be repeated every 3 to 6 months, depending on mineral content and usage of
water cooler.
Note: Cleaning with vinegar or lemon acid also destroys bacteria and Biofilm.
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 14
TROUBLESHOOTING
Dispenser is not operating.
• Make sure that the power cord is properly connected to a working outlet.
Water is leaking.
• Replace water bottle. Most common cause is a cracked bottle.
• Call 1-844-452-2425 for assistance.
Push buttons are stuck and/or faucets are leaking.
• Apply mineral oil (baby oil) to the button slides to reduce friction.
No water is coming from the taps.
• Make sure that the bottle is not empty. If so, replace it.
• Make sure that you fully press the water controls.
• Remove bottle receptacle as per page 9 step 1. Shake bottle receptacle vigorously for a
few seconds then replace.
Water dispensed is not cold.
• It takes up to 1 hour after setup to dispense cold water.
• Make sure that the back of the dispenser is at least 4 inches from a wall and that air is free
to flow on all 4 sides of the dispenser.
• Make sure that the tank is not overfilled. Dispense water until bubbles appear in the bottle.
Water dispensed is not hot.
• It takes 15-20 minutes after setup to dispense hot water.
• Make sure that the power cord is properly connected to a working outlet.
• Make sure that the energy saving switch is ON.
Dispenser is noisy.
• Make sure that the dispenser is positioned on a level surface.
Water tastes bad.
• Drain the water from the reservoirs and replace the bottle with a fresh one.
• Clean dispenser as outlined in “ Proper Care & Descaling ” section.
Cleaning stainless steel.
• This treatment removes and prevents finger prints from marring surface. Please rub in
small amount of mineral oil ( Unscented Baby oil) wipe clean, it will enrich the looks.
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Model # 7LIECH-SSF-G: Page 15
LIMITED WARRANTY
Electrotemp Technologies Inc., (“Vendor”) warrants to the original purchaser of this dispenser, and to no
other person, that if this dispenser is assembled and operated in accordance with the printed instructions
accompanying it, then for a period of one (1) year from the date of purchase, all parts in such dispenser
shall be free from defects in material and workmanship. Vendor may require reasonable proof of your date
of purchase from an authorized retailer or distributor. Therefore, you should retain your sales slip or invoice. The Limited Warranty shall be limited to repair or replacement of parts, which prove defective under
normal use and service and which Vendor shall determine in its reasonable discretion upon examination to
be defective. Before returning any parts, you should contact Vendor’s Customer Service Department using
the contact information listed below. If Vendor confirms, after examination, a defect covered by this Limited
Warranty in any returned part, and if Vendor approves claim, Vendor will replace such defective part
without charge. If you return defective parts, transportation charges must be prepaid by you. Vendor will
return replacement parts to original purchaser, freight or postage prepaid.
The Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse,
alteration, misapplication, improper installation or improper maintenance or service by you or any third
party, or failure to perform normal and routine maintenance on the dispenser, as set out in the User’s
Manual. In addition, the Limited Warranty does not cover damages to the finish, such as scratches, dents,
discoloration or rust after purchase.
The Limited Warranty is in lieu of all other express warranties. Vendor disclaims all warranties for products
that are purchased from seller other than authorized retailers or distributors. AFTER THE PERIOD OF
THE ONE (1) YEAR EXPRESS WARRANTY, VENDOR DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. FURTHER, VENDOR SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTAL DAMAGES. Vendor assumes no responsibility for any defects caused by
third parties. This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other
rights depending upon where he or she lives. Some jurisdictions do not allow exclusion or limitation of
special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above
exclusion and limitations may not apply to you.
Warranty is void if the electrical outlet is improperly wired to incorrectly sized circuit breaker or fuse,
if not grounded properly, or wires do not have correct polarity.
Use of this cooler confirms Purchasers agreement with the conditions of this warranty.
Electrotemp Technologies Inc.
406 Watline Avenue
Mississauga, Ontario, Canada, L4Z-1X2
1-844-926-6537
www.electrotemp.com
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-844-452-2425 for assistance.
Download PDF
Similar pages