FILTERBREW &
SERVING CONCEPT
TECHNICAL MANUAL
TM_EN
Part No.: 1764092_02
CONTENT
FILTERBREW & SERVING CONCEPT
CONTENT...........................................................................................................................................................................................2
GENERAL..............................................................................................................................................................................................4
Introduction.......................................................................................................................................................................................................4
Warnings.............................................................................................................................................................................................................4
Precautions.........................................................................................................................................................................................................4
Intended use.......................................................................................................................................................................................................4
CLEANING AND CARE..............................................................................................................................................................5
Rinse Thermos, Decanter and Serving station...........................................................................................................................................5
Dayly cleaning....................................................................................................................................................................................................6
Weekly cleaning.................................................................................................................................................................................................6
Cleaning Serving station......................................................................................................................................................7
Exterior cleaning...............................................................................................................................................................................................7
PROGRAMMING.............................................................................................................................................................................8
A-2, DA-4, Thermos A, Mega Gold A............................................................................................................................................................8
Cater................................................................................................................................................................................................................. 10
Tower................................................................................................................................................................................................................ 14
HVA/HVM........................................................................................................................................................................................................ 16
Grinder Original ........................................................................................................................................................................................... 17
POSSIBLE SOLUTION...............................................................................................................................................................19
Original A/M.................................................................................................................................................................................................... 19
Cater, Tower, HVA/HVM............................................................................................................................................................................... 20
ELECTRICAL SCHEMATICS...................................................................................................................................................21
A-2..................................................................................................................................................................................................................... 21
M-2.................................................................................................................................................................................................................... 22
DA-4.................................................................................................................................................................................................................. 23
DM-4................................................................................................................................................................................................................. 24
Mega Gold A, Termos A................................................................................................................................................................................. 25
Mega Gold M, Termos M, Office.................................................................................................................................................................. 26
Single Cater..................................................................................................................................................................................................... 27
Cater................................................................................................................................................................................................................. 28
Tower 3x400VAC+Zero+Ground............................................................................................................................................................. 29
Tower 3x230VAC+Ground......................................................................................................................................................................... 30
Tower 3x400-500VAC+Ground................................................................................................................................................................. 31
Grinder Original ........................................................................................................................................................................................... 32
V-2..................................................................................................................................................................................................................... 33
HVA/HVM 1-Phase........................................................................................................................................................................................ 34
HVA/HVM 3-Phase........................................................................................................................................................................................ 35
EXPLODED VIEW.........................................................................................................................................................................36
A-2..................................................................................................................................................................................................................... 36
M-2.................................................................................................................................................................................................................... 38
2
CONTENT
FILTERBREW & SERVING CONCEPT
DA-4................................................................................................................................................................................................................... 40
DM-4.................................................................................................................................................................................................................. 42
Mega Gold A.................................................................................................................................................................................................... 44
Mega Gold M.................................................................................................................................................................................................... 46
Thermos Office............................................................................................................................................................................................... 48
Thermos A........................................................................................................................................................................................................ 50
Thermos M....................................................................................................................................................................................................... 52
Cater.................................................................................................................................................................................................................. 54
Cater tank......................................................................................................................................................................................................... 56
Tower................................................................................................................................................................................................................. 58
Grinder original .............................................................................................................................................................................................. 60
Grinder EK21................................................................................................................................................................................................... 62
HVA\HVM......................................................................................................................................................................................................... 64
V-2...................................................................................................................................................................................................................... 66
Serving station 2.5L........................................................................................................................................................................................ 67
Serving station 5L........................................................................................................................................................................................... 69
DIMENSION...................................................................................................................................................................................... 71
A-2/M-2............................................................................................................................................................................................................. 71
DA-4/DM-4...................................................................................................................................................................................................... 72
Thermos A/M................................................................................................................................................................................................... 73
Mega Gold A/M................................................................................................................................................................................................ 74
Single Tower...................................................................................................................................................................................................... 75
Tower................................................................................................................................................................................................................. 76
Single Cater/ Tea Cater.................................................................................................................................................................................. 77
Cater.................................................................................................................................................................................................................. 78
Serving station 5L........................................................................................................................................................................................... 79
Serving station 2.5L........................................................................................................................................................................................ 80
V-2...................................................................................................................................................................................................................... 81
HVA/HVM..............................................................................................................................................................................82
Grinder Original ............................................................................................................................................................................................ 83
Some important information may appear in textboxes seen below
IMPORTANT!
INFO.
CAUTION!
INFO.
More INFO.
Note
INFO.
3
GENERAL
FILTERBREW & SERVING CONCEPT
Introduction
Thank you for choosing a FILTERBREWER coffee machine.
We hope you enjoy it !
Read the user guide before using the machine.
This guide contains important instructions for
proper and safe use of the vending machine.
Always keep this guide close at hand for future
reference.
Warnings
Never immerse the machine, plug or mains
cable in water because there is a danger of
electric shock.
The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning the use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure they
do not play with the appliance.
Do not use the machine if the mains cable, plug
is damaged or the machine has fallen down.
If the mains cable is damaged it must be
replaced by the manufacturer, service agent or
similarly qualified persons in order to avoid a
hazard.
Only plug the machine into a properly installed
earthed safety socket whose line voltage
matches the technical data for the machine.
Precautions
Do not use the machine outdoors so it can be
exposed to weather (rain, snow, frost). It will
cause material damage to the machine.
Do not try to open the machine or repair it in
any way. To avoid danger only have the machine
repaired in a technical workshop, Service
Centre or by a qualified person.
Remove the mains cable from the socket when
the machine is not in use for longer periods. To
do this, pull the plug not the cable.
This appliance must be placed in a horizontal
position which is resistant to any water that
may leak.
Place the machine out of the reach of children.
Position the mains cable so that people cannot
trip over it. Keep it away from sharp edges and
heat sources.
The new hose-sets supplied with this appliance
are to be used, old hose-sets must not be reused.
This appliance is not suitable for installation in
an area where a water jet could be used.
This appliance must not be cleaned by a water
jet.
Intended use
This appliance is intended to be used in
household and similar applications such as:
- Staff kitchen areas in shops.
- Offices and other commercial working
environments.
- On agricultural estates.
- By clients in hotels, motels and other
residential type environments.
- Bed and breakfast type environments.
4
For the optimal performance of the machine
these parameters shall not be exceeded:
- Maximum permissible inlet water pressure :
800KPa (8Bar)
- Minimum permissible inlet water pressure:
200KPa (2Bar)
- Maximum working temperature: 40°ºC
- Minimum working temperature: 10°ºC
CLEANING AND CARE
FILTERBREW & SERVING CONCEPT
Rinse Thermos, Decanter and Serving station
Before each brewing, rinse the thermos, decanter or serving station with fresh tap water.
When cleaning the outside, use a soft rag with liquid cleaning agent to prevent scratches.
CAUTION!
The machine should not be submerged
in water or washed in a dishwasher. it
will result in machine damage.
5
CLEANING AND CARE
FILTERBREW & SERVING CONCEPT
Dayly cleaning
Wash the thermos, decanter(B) and the filter holder with liquid solution for coffee machines. Always
remove the filter immediately and clean the filter holder daily, coffee will get moldy.
Clean the spray nozzle(A) and the surrounding area.
Use a soft rag and liquid solution that does not scratch.
A
B
B
Pitcher
PT No.110351
Weekly cleaning
Descaling and cleaning.
Pour 50 ml descaling / cleaning solution in a decanter and fill it up with cold water.
Pour the mixture in the machine and proceed with a brewing without a filterpaper or coffee.
Rinse the machine thoroughly by brewing at least 3 times with clean water so that the particles from
descaling solution disappear.
Regular descaling will ensure optimum brewing performance and a longer life of the machine.
When cleaning the decanter in a dishwasher. Dismantle lid and place decanter upside down in the
dishwasher.(A)
A
Descaling agent
PT No. 110412
6
CLEANING AND CARE
FILTERBREW & SERVING CONCEPT
Cleaning Serving station
A
Disassemble the level tube and clean it
every week with the enclosed brush.
Take off the main lid and clean the mixer
tube(A).
Cleaning of Serving station
IMPORTANT!
Rinse the inside of
the serving station
several times with
fresh tap water.
Fill the serving station with hot water. ( Full
brewing without coffee and filter ).
Put 1 tablespoon with cleaning powder in the
serving station and wait at least 15 minutes.
Tap out 2/3 of the cleaning solution.
Clean the serving station with the cleaning brush.
Rinse the serving station with fresh tap water several times before reuse.
OPTIONS
Part No.
CLEANING PARTS
110102-02
Cleaning powder
1104231
Cleaning brush
1103360
Cleaning brush for level tube,
mixer tube
Exterior cleaning
When cleaning exterior of the machine, use a soft rag with liquid cleaning agent
to prevent scratches.
7
PROGRAMMING
FILTERBREW & SERVING CONCEPT
A-2, DA-4, Thermos A, Mega Gold A
Select machine type
Enter the procedure to select machine type is the following:
Press all three buttons
,
and
at the same time
before turning on the mains switch The buzzer beeps once.
The display shows the current setting.
Step up with button
Press the button
8
and step down with button
.
to save setting and exit to normal mode.
MACHINE
TYPE
DISPLAY
CUPS
CUPS TIME
BUZZER TIME
DA/A-2
T1
4-12
9.25 s
247
Termos A
T2
4-15
9.25 s
292
Mega A
T3
4-17
9.25 s
344
PROGRAMMING
FILTERBREW & SERVING CONCEPT
A-2, DA-4, Thermos A, Mega Gold A
Adjust water amount
Adjust amount of brew water
Press the buttons
and
at same time in 5 seconds.
The buzzer beeps twice. Display shows 0.
- Press the
button to increase amount of water.
- Press the
button to decrease amount of water.
- 1 step = 5%
- Press the
button to confirm the change.
ADJUST
DISPLAY
25%
5
20%
4
15%
3
10%
2
5%
1
0%
0
-5%
-1
-10%
-2
-15%
-3
-20%
-4
-25%
-5
Adjust brew time
Adjust the brew time
Press the buttons
and
at same time in 5 seconds.
The buzzer beeps four times. Display shows 0.
- Press the
button to increase brewing time.
- Press the
button to decrease brewing time.
- 1 step = 5%
- Press the
Display shows
button to confirm the change.
and machine is ready to use.
9
PROGRAMMING
FILTERBREW & SERVING CONCEPT
Cater
Normal operation with reduced outlet time
This mode is entered by pressing the
and
before turning the
mains switch on. The buzzer gives a 5s beep to indicate this mode.
This machine operates like in normal mode but the outlet times are reduced by
90% in order to allow faster adjustment of valve times.
Adjusting of water temperature
Press buttons
and
at the same time for 5 seconds until you
hear one beep. Display shows the present setting
Adjust with the buttons
= (increase) and
Confirm the new settings by pressing the
70°0C = min. temperature.
96°0C = max. temperature.
= (decrease).
button.
Adjusting of temperature sensor
ADJUST
DISPLAY
+5°C
5
+4°C
4
+3°C
3
+2°C
2
+1°C
1
0
0
-1°C
-1
-2°C
-2
-3°C
-3
-4°C
-4
-5°C
-5
10
In this mode a temperature offset for the NTC sensor can be adjusted.
The procedure to enter this mode is the following:
Press buttons
,
and
at the same time for 5
seconds until you hear 2 beeps.
The display shows the current setting.
Adjust with the buttons
Pressing the
mode.
= (increase) and
= (decrease).
button to save new settings and return to normal
PROGRAMMING
FILTERBREW & SERVING CONCEPT
Cater
Adjusting of water quantity
ADJUST
DISPLAY
25%
5
20%
4
15%
3
10%
2
5%
1
0%
0
-5%
-1
-10%
-2
-15%
-3
-20%
-4
-25%
-5
The procedure to enter this mode is the following:
Press buttons
and
at the same time for 5 seconds until
you hear 3 beeps.
The display shows the current setting.
Adjust with the buttons
Presse the
= (increase) and
= (decrease).
button to save new settings and return to normal
mode.
Adjusting of brewing time
ADJUST
DISPLAY
25%
5
20%
4
15%
3
10%
2
5%
1
0%
0
-5%
-1
-10%
-2
-15%
-3
-20%
-4
-25%
-5
Note
In this mode the time for the brewing done buzzer activation can be
adjusted. The procedure to enter this mode is the following:
Press buttons
and
at the same time for 5
seconds until you hear 5 beeps.
The display shows the current setting.
Adjust with the buttons
Presse the
= (increase) and
= (decrease).
button to save new settings and return to
normal mode.
The brewing time is the same regardless adjustment of the outlet valve time.
11
PROGRAMMING
FILTERBREW & SERVING CONCEPT
Cater
Select machine type
In this mode the machine type can be chosen. The procedure to enter this mode is the following:
Press buttons
,
and
at the same time
before turning the mains switch on until you hear 6 beeps.
The display shows the machine type.
Step up with button
Presse the
and step down with button
.
button to save new setting and return to
normal mode.
Outlet time (s)
Full
Half
Machine type
Display
Buzzer time (s)
1.8L
T1
56
113
90
2.5L
T2
79
158
90
Adjusting of flow water
IMPORTANT!
From date 091001 Cater is delivered with an adjustable PDS valve. This is to improve the
water flow into filter holder. The flow of PDS valve is set to 0.95 litre /minute. Depending
on the coarseness and amount of coffee that’s used when brewing, the flow might need
adjustments to prevent overflow in the filter holder.
A
PDS valve
12
Check the water flow.
This should be 0.95L/minute.
Adjust PDS valve if necessary.
(See fig.A)
Shall been done by an authorized
installation engineer
PROGRAMMING
FILTERBREW & SERVING CONCEPT
Cater
Test functions
Press buttons
and
at the same time before turning the mains
switch on, puts the control board into test mode for time and temperature
controlled machines.
For the other types pressing buttons
in test mode.
and
before power-on results
A test sequence starts:
- Turn all outputs off
- Turn V_WATER on for 3 s
- Turn V_OUT_A on for 3 s
- Turn HEAT on for 3 s
- Turn buzzer on for 2 s
- Show NTC temperature on displayed
- If button
is pressed display
b1
- If button
is pressed display
b2
- If button
is pressed display
- If LVL_SAFE is passive display
- If LVL_REF is passive display
b3
L1
L2
13
PROGRAMMING
FILTERBREW & SERVING CONCEPT
Tower
Normal operation with reduced outlet time
This mode is entered by pressing
and
before turning the mains
switch on. The buzzer gives a 5s beep to indicate this mode.
This machine operates like in normal mode but the outlet times are reduced by 90% in order to allow
faster adjustment of valve times.
Adjusting of temperature sensor
ADJUST
DISPLAY
+5°C
+4°C
+3°C
+2°C
+1°C
0
-1°C
-2°C
-3°C
-4°C
-5°C
5
4
3
2
1
0
-1
-2
-3
-4
-5
In this mode a temperature offset for the NTC sensor can be adjusted.
The procedure to enter this mode is the following:
Press buttons
,
and
at the same time for 5
seconds until you hear 2 beeps.
The display shows the current setting.
Adjust with the buttons
Pressing the
= (increase) and
= (decrease).
button to save new settings and return to normal
mode.
Select machine type
In this mode the machine type can be chosen. The procedure to enter this mode is the following:
Press buttons
,
and
at the same time before turningthe mains switch on until
you hear 6 beeps.
The display shows the machine type.
Step up with button
Presse the
14
and step down with button
.
button to save new setting and return to normal mode.
OUTLET TIME (s)
FULL
HALF
MACHINE TYPE
DISPLAY
BUZZER TIME(s)
10L
T1
300
600
300
5L
T2
150
300
300
PROGRAMMING
FILTERBREW & SERVING CONCEPT
Tower
Adjusting water temperature
A
Press left buttons
and
at the same time for 5 seconds until
you hear1 beep. Display shows the present setting(A).
Adjust with the left buttons
(increase water temp.) and
(decrease water temp.)
Confirm the new settings by pressing the left
70°0C = min. temperature.
96°0C = max. temperature.
button once.
Adjusting water quantity
ADJUST
DISPLAY
25%
20%
15%
10%
5%
0%
-5%
-10%
-15%
-20%
-25%
5
4
3
2
1
0
-1
-2
-3
-4
-5
For left side
Press left buttons
and
at the
same time for 5 seconds until you hear 3
beeps. the display shows the current setting.
Adjust with the left buttons
(increase) and
(decrease)
Confirm the new settings by pressing the
left
button once.
For right side
Press right buttons
and
at the same time for 5 seconds until
you hear 3 beeps. the display shows the current setting.
Adjust with the right buttons
(increase) and
Confirm the new settings by pressing the right
(decrease)
button once.
15
PROGRAMMING
FILTERBREW & SERVING CONCEPT
HVA/HVM
Select machine type
Use a decanter to fill up the water tank to the long sensor pin.(A)
Keep button (B) pressed while turning on the power switch.(D)
A
A
D
E
B
C
The display will show T1, change the type of machine with buttons (B) or (C).
T1 = HVA automatic
T2 = HVM manual
Confirm the choice by holding down the buttons (B) and (C) at the same
time for approximately 5 seconds.
Note
16
Install the plug supplied in the inlet valve (E) to avoid possible
leakage.
PROGRAMMING
FILTERBREW & SERVING CONCEPT
Grinder Original
Normal operation
There are several sub modes for this mode:
A
READY
The machine is in this mode after power on. The motor is off and timers are
stopped.
Pressing the button
and
changes the number of cups to be
prepared.The number of cups is displayed on the 2 digit display. The range is 4 -34
cups.The latest number of cups will be used even after power cycling the machine.
Pushing the button
to start the motor timer (number of cups x time per
cup) and activates the motor V_MOTOR and moves the machine into GRINDING
mode.
GRINDING
The display is blinking at 0.5 Hz. The timer is checked. After the motor time has
expired the the motor is turned off. Pushing the button
again pauses the
timer, deactivates the motor and moves into PAUSED mode. If button
pressed more than 5 s the machine moves to READY mode.
is
PAUSED
The displays is blinking at 2 HZ. If the
button is pressed again a beep
signals the recognition of the button press and the machine moves back to
GRINDING mode after 2 s unless the
is still pressed and keeps pressed
more than 5 s which moves the machine to READY mode.
A djust time per cup
In this mode the time for the motor activation per selected
number of cups can be adjusted. The procedure to enter this
mode is the following:
DISPLAY
TIME/CUP
Digit 1
Digit 2
1.0
1
0
...
...
...
9.9
9
9
Press buttons
and
for 5 seconds until you hear
3 beeps.
The display shows the current setting.
Increase inlet valve time with
Press
and decrease with
.
to save new settings and return to normal mode.
The adjustment is made in 0.1 s steps. The range is 1.0 to 9.9 s
per cup.
The time per cup is saved permanently.
17
PROGRAMMING
FILTERBREW & SERVING CONCEPT
Grinder Original
Adjust coffee amount
A
Press buttons
and
simultaneously for 6 seconds.
The display (A) shows the current time setting for grinding.
You can now choose to increase or decrease the time 15 = 1.5 seconds for
or
grinding, by pressing the buttons
.
This means that you increase or decrease the amount of coffee grounds.
Adjust coffee grind
A
The grinding degree
is preset from the factory.
Push the knob and turn counterclockwise (A) for coarser grind or clockwise (B)
for finer grinding.
B
Testing
Pressing the
and
buttons before turning the mains switch on
puts thecontrol board into test mode.
A test sequence starts:
- Turn all outputs off
- Turn V_MOTOR on for 3 s
- Turn buzzer on for 2 s
- If button
- If button
- If button
18
b1
is pressed display
b2
is pressed display
is pressed display
b3
POSSIBLE SOLUTION
FILTERBREW & SERVING CONCEPT
Original A/M
Fault and solution
FAULT
IMPORTANT!
All maintenance
and installations
must be done
of an authorized
technician.
Power switch does not lit
POSSIBLE SOLUTION
- Check plug connection to wall socket.
- Check fuse in plug.
- Check if hot plate becomes warm, if so
replace power switch.
Hot plate does not become - Check connection to hot plate.
warm although switch is lit. - If hot plate is defective, replace.
Brewer excess steam.
- Machine may require descaling.
- Spray nozzel may need unblocking.
- Hose may be bent.
- Inlet to boiler may be blocked. Descale
machine - if boiler still defective - replace.
Machine will not brew.
- Check overheating protection.
- Check microswicth.
- Check connection to boiler.
- Boiler unit may need replacing.
The machine does not take
in water
- Make sure water tap is open.
- Make sure the water hose is not bent.
- Check inlet valve.
- Check that the display is blinking.
The machines does not
stop taking in water.
- Dirt in the inlet valve.
- inlet valve is defective - replace
- PCB is defective - replace
The machine is giving
wrong amount of water.
- Check water tap.
- Water hose is bent.
- Dirt in inlet valve.
-Water amount adjustment set in display is
adjusted faulty. Adjust according to page 21.
- Defect floatregulator in inlet valve - replace
19
POSSIBLE SOLUTION
FILTERBREW & SERVING CONCEPT
Cater, Tower, HVA/HVM
Fault and solution
LEVEL CONTROL
Remove the power
cord from the wall
socket during any
installation work.
SHOWN ON THE
DISPLAY
POSSIBLE FAULT
- The high water level
sensor is triggerd
before the low level
sensor.
IMPORTANT!
All maintenance
and installations
must be done
of an authorized
technician.
POSSIBLE
SOLUTION
- Clean the level sensor.
- Replace.
- Cables connected is
incorrectly.
- The machine fills slowly.
- Check water
- Poor water pressure.
connection.
- Water connection tap
- Restart machine.
is not open
TEMPERATURE CONTROL
SHOWN ON THE
DISPLAY
20
POSSIBLE FAULT
POSSIBLE
SOLUTION
- Temperature sensor
out of range.
- Temperature sensor is
broken.
- Cable loose.
- 50C - 1050C.
- Replace temperature
sensor.
- Check cables.
- Heating time too long.
- Solid state broken.
- Element broken.
- Overheating guard
tripped or broken.
- Restart the machine.
- Replace element.
- Replace solid state.
- Check overheating
protection.
Rocket Switch
Double
Heating Plate
A2
A2
Black
IN2
UT4
IN5
UT3
IN6
7
6
14
4
PCB Original A
UT1
Black
Black
Blue
Black
Blue
Blue
Yellow/Green
A1
Black
A1
Blue
AUT
ELH
MIC 1
MIC 2
Micro Switch
Blue
Brew Element
MAN
ELH
Heating Plate
Black
Black
Black
Blue
Inlet Valve 1.8L
VENT
230
VENT
230
Main Socket
230
Yellow/Green
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
A-2
21
22
IN2
6
IN5
Brew Lamp
Black
Black
IND
Black
15
13
11
Rocket Switch
Double
UT4
OPL
IND
Blue
Blue
Blue
Rocket Switch
Double
Black
Blue
Blue
Black
AUT
M2
Heating Plate
M2
ELH
230
Main Socket
230
MAN
ELH
Black
Black
230
Yellow/Green
Brew Element
MIC 1
MIC 2
Miscro Switch
Black
Heating Plate
M2
M2
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
M-2
Black
MIC1
Microswitch 2
MIC2
Temperture
Controller 2
AUT Black
ELT
Blue
A1
4
6
14
7
MAIN
PCB 2
Blue
Black
Over Heating
Protector 2
MAIN
Heating Plate 3
Blue
A2
Blue
A1
Heating Element 2
ELT
Black
AUT
Black
Yellow/Green
Black
IN6
Black
UT4
Blue UT3
Blue IN6
Heating Plate 4
A2
Black
Rocket Switch
Double 2
Black
IN2
Yellow/Green
IN5
VENT
VENT
VENT
Double inlet valve
VENT
IN2
IN5
UT4
UT3
IN6
Black
IN6
Rocket Switch
Double 1
Black
Black
Connector FV
Black
Blue
Blue
Black
Heating Plate 1
A2
Blue
Blue
Blue
230
230
230
230
A2
Blue
MAIN
Blue
Blue
Black
ELT
Black
7
6
14
4
AUT
AUT
MIC2
Black
Microswitch 1
MIC1
Temperture
Controller 1
Heating Element 1
ELT
PCB 1
Over Heating
Protector 1
MAIN
A1
A1
Heating Plate 2
Black
DA-4
Yellow/Green
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
23
Black
AUT
INT
Black
AUT
Temperture
Controller 2
MIC1
Microswitch 2
MIC2
Black
INT
ELT
ELT
M2
M2
Blue
Blue
Heating Element 2
Black
Heating Plate 4
MAIN
MAIN
Over Heating
Protector 2
Black
Blue
Heating Plate 3
M2
M2
Blue
Blue
6
11
Rocket Switch
Double 2
13
UT4
Black
15
230
230
230
230
Yellow/Green
Connector FV
Rocket Switch
Double 1
15
13
6
UT4
OPL
11
Blue
Blue
Blue
M2
M2
MAIN
MAIN
Over Heating
Protector 1
Black
Heating Plate 2
Blue
Blue
ELT
ELT
INT
Black
Black
INT
AUT
AUT
Temperture
Controller 1
MIC2
Microswitch 1
MIC1
Heating Plate 1
Heating Element 1
M2
Black
M2
Black
24
FILTERBREW & SERVING CONCEPT
ELECTRICAL SCHEMATICS
DM-4
Black
Black
A-1
3
2
1
6
5
4
Blue
PCB Original A
Rocket Switch
Green/Yellow
Black
Black
Blue
A-1
Black
MIC 1
MAN
ELH
MIC 2
Black
Blue
Black
Brew Element
Micro Switch
AUT
ELH
Blue
230
VENT
Inlet Valve 1.8L
VENT
Main Socket
230
230
Green/Yellow
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
Mega Gold A, Termos A
Note:
- Thick wire ≥ 100V
- Thin wire ≤ 24V
25
26
UT 5
Brew Lamp
IND
Rocket Switch
Black
IND
IN 4
UT 2
IN 1
Black
Black
Blue
Blue
Black
19
Blue
M1
Blue
AUT
Main Socket
230
Black
230
ELH
Brew Element
230
MAN
ELH
MIC 1
Micro Switch
Black
MIC 2
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
Mega Gold M, Termos M, Office
3
2
Rocket Switch
6
5
4
Blue
Blue
Inlet
Green Yellow
Brew Lamp
Blue
Blue
Black
Black
PCB
Black
Black
Tank GND
Element
NTC
Red
Black
Level
Sensor
Black
Black
Black
Black
High Limit
Switch
Black
Solid State
Note:
- Thick wire ≥ 100V
- Thin wire ≤ 24V
Blue
Black
Green Yellow
Black
Blue
Main Socket
Black
1
Blue
Black
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
Single Cater
27
ELECTRICAL SCHEMATICS
Cater
28
FILTERBREW & SERVING CONCEPT
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
3
L3
T
L2
S
220V
L1
R
220V
N
High limit switch
220V
ZERO
GND
5
6
2
Switch
4
1
Fuse
Relay
Outlet-1
Outlet-2
PCB
Tank GND
Tower 3x400VAC+Zero+Ground
29
30
3
GND
5
6
2
Switch
4
1
High limit switch
Fuse
T
L2
S
220V
R
L3
220V
L1
Relay
Outlet-1
Outlet-2
Inlet
PCB
EL-1
R-S
NTC
Solid state-1
Tank GND
EL-3
S-T
Solid state-2
EL-2
T-R
Solid state-3
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
Tower 3x230VAC+Ground
220V
L1
L2
R
S
3
230V
Zero N
Transformer 400-500VAC
GND
5
6
2
Switch
4
1
High limit switch
Fuse
L3
T
400-500V
L2
S
400-500V
R
L1
Relay
Outlet-1
Outlet-2
Inlet
PCB
EL-1
R-S
NTC
Solid state-1
Tank GND
EL-3
S-T
Solid state-2
EL-2
T-R
Solid state-3
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
Tower 3x400-500VAC+Ground
400-500V
31
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
Grinder Original
Note:
- Thick wire ≥ 100V
- Thin wire ≤ 24V
32
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
V-2
Chassis
GND
Chassis
GND
Heating Plate 1
Heating Plate 2
Brown
Brown
White
1
4
2
5
White
1
3
ROCKET
SWITCH
4
2
5
3
6
6
Black
Black
Blue
Blue
ROCKET
SWITCH
Chassis
GND
230V Input
Main Power
Socket
33
34
Inlet valve
Inlet
Inlet
Rocket
Switch
5
6
2
3
Main socket
4
1
Blue
Blue
230
Chassis
GND
Black
Black
Yellow/Green
Yellow/Green
230
230
PCB
7
Black
6
Black
14 4
1 3
10 2 9
8
Black
Tank
Short
Black
Sol1
Tank
Long
Sol4
Black
Red
Black
Blue
4
1
Black
Sol3
Sol2
EL
Black
Solid state
3
2
ELE
ELE
Blue
NTC
High limint
Switch
OH
OH
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
HVA/HVM 1-Phase
ELECTRICAL SCHEMATICS
FILTERBREW & SERVING CONCEPT
HVA/HVM 3-Phase
Blue
Red
Black
Black
Blue
Red
Black
Note:
- Thick wire ≥ 100V
(Black, Blue wire)
- Thin wire ≤ 24V
35
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
A-2
Drawing
11
12
13
Tank
Float
Strainer
Cover
Microswitch holder
1
2
14
6
3
15
7
8
16
9
4
17
19
10
5
18
20
23
21
22
34
24
25
26
36
27
28
29
30
31
32
33
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
A-2
Spare parts list
POS.
PCS
Part No.
1
2
3
4
4
5
6
7
8
9
10
11
12
13
14
14
15
16
17
18
18
19
20
20
21
22
23
23
24
25
26
27
28
29
30
31
32
33
34
1
2
1
2
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
120433
110001
1102016
120811 (230V)
1208121 (110V)
160101
1204014
1505041
1204016
1402150
120422
1204012
1204013
1204015
160821 (230V)
1608221 (110V)
1561036
1505022
1206123
120620-01 (230V)
120617 (110V)
160212-03
1205101 (230V)
120505 (110V)
140339
1505021
1031640 (230V)
1031643 (110V)
120320
1402163
1505063
160802-04
160570
1603854
160565
1505042
1264161
1264160
2760094
Description
Lid, Glass decanter
Decanter CQ glass
Brew basket 1.8L 90 mm
Warming plate 230V/95W
Warming plate 110V/95W
Heat coil 95W
Microswitch holder
Hot water hose 1.8L
Spray nozzle for water tank
Screw T20,M4X8mm
Air inlet plastic 1.8L
Lid of tank original
Strainer original
Water tank complete 1.8L
Micro switch tank 1.8L
Micro switch 125V
Drainage hose 1.8L
Inlet hose 400mm
Non return valve 1.8L
Valve inlet single 1.8L
Inlet coil 110V
Over heating protection
Brewing element 230V/2200W
Brewing element 110V/1600W
Clip for hose 16.4mm
Silicon hose cold W 1.8L
Electronic unit PCB Original
Electronic unit PCB Original 110V
Rubber feet V2
Screw M4X8mm
Bottom rubber TPE
Rocker switch double
Power cord inlet/Main socket
Membran switch origi A
Main supply cable / Europe
Inlet hose 3/4”-1/2”
Gasket DIA23.5mm x 15mm D3mm
Gasket DIA18mm x 9mm D2mm
Gasket set for inlet hose
37
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
M-2
Drawing
10
11
12
Tank
Float
Strainer
Cover
Microswitch holder
1
2
13
14
3
6
15
7
8
4
9
17
16
5
18
20
19
21
22
23
24
26
27
38
25
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
M-2
Spare parts list
POS.
PCS
Part No.
Description
1
1
120433
Lid, Glass decanter
2
2
110001
Decanter glass
3
1
1102016
Brew basket 1.8L 90 mm
4
2
120811 (230V)
Warming plate 230V/95W
4
2
1208121 (110V)
Warming plate 110V/95W
5
1
160101
Heat coil 95W
6
1
1505041
Silicon hose hot 1.8L
7
1
1204016
Spray nozzle for water tank
8
1
1402150
Screw T20 M 4x8mm
9
1
120422
Air inlet plastic 1.8L
10
1
1204012
Lid of tank original
11
1
1204013
Strainer original
12
1
1204015
Water tank complete 1.8L
13
1
160821 (230V)
Micro switch tank 1.8L
13
1
1608221 (110V)
Microswitch 125V
14
1
1204014
Microswitch holder
15
1
1505062
Overflow hose
16
1
1206123
Non return valve
17
1
160212-03
Over heating protection
18
1
1205101 (230V)
Brewing element 230V/2200W
18
1
120505 (110V)
Brewing element 110V/1600W
19
4
140339
Clip for hose 16.4mm
20
1
1031503
Silicon hose cold complete
21
1
160565
Main supply cable / Europe
22
1
160570
Power cord inlet/Main socket
23
1
160804-04
Brewing lamp
24
1
160802-04
Rocker switch double
25
1
1505063
Rubber bottom TPE
26
4
120320
Rubber feet V2
27
4
1402163
Screw M4x8
39
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
DA-4
Drawing
Tank
Float
Strainer
Cover
Microswitch holder
6
1
16
2
10
13
14 15
7
8
12
3
11
9
4
5
17
18
19
21
22
23
26
24
25
27
28
29
40
30
31
32
33
34 35
36
20
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
DA-4
Spare parts list
POS.
PCS
1
1
120433
Part No.
Decanter lid
Description
2
4
110001
Decanter CQ glass
3
2
1204012
Lid of tank original
4
2
1204013
Strainer
5
2
1102016
Brew basket 1.8L 90 mm
6
2
1204015
Water tank complete 1.8L
7
2
120422
Air inlet plastic 1.8L
8
1
1402150
Screw T20,M4X8
9
2
1031503
Silicon hose cold complete
10
2
1505041
Silicon hose hot 1.8L
11
2
160212-03
Over heating protection
12
1
150501
Silicone tube 8x12mm
13
1
1505042
Inlet hose 3/4”-1/2”
14
1
1206603
Gasket DIA23.5mm x 15mm D3mm
15
1
1206604
Gasket DIA18mm x 9mm D2mm
16
1
2760094
Gasket set for inlet hose
17
4
140339
Clip for hose 16.4mm
18
2
1205101
Brewing elemnet 230V/2200W
19
1
120621-01
Inlet valve 0.95x2L Double
20
2
1505062
Overflow tube
21
2
1206123
Non return valve
22
1
1605651
PG complete (PG16)
23
1
160549
Connector fv122
24
2
1204016
Spray nozzle for water tank
25
6
160536
Gasket rubber NBR(Rubber TRP 30.0)
26
1
1505063
Rubber bottom TPE
27
4
120320
Rubber feet V2
28
4
1402163
Screw M4x8
29
4
120811
Warning plate 230V/95W
30
1
160101
Heat coil 95W
31
2
1031640
Electronic unit PCB Orginal
32
2
160802-04
Rocker switch double
33
2
1603854
Membran switch origi A
34
2
160821
Micro switch tank 1.8L
35
1
1204014
Microswitch holder
36
1
1605210
Power cable 4 x 1.5mm
41
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
DM-4
Drawing
Tank
Float
Strainer
Cover
Microswitch holder
6
1
2
7
9
3
10
8
4
5
12
11
13
18
14
15
16
17
19
23
20
9
24
21
25
22
26
42
27
28
30
29
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
DM-4
Spare parts list
POS.
PCS
Part No.
Description
1
1
120433
Decanter lid
2
4
110001
Decanter CQ glass
3
2
1204012
Lid of tank original
4
2
1204013
Strainer
5
2
1102016
Brew basket 1.8L 90 mm
6
2
1204015
Water tank complete 1.8L
7
2
1505041
Silicon hose hot 1.8L
8
2
120422
Air inlet plastic 1.8L
9
12
1402150
Screw T20,M4X8
10
2
160212-03
Over heating protection
11
1
1605651
PG complete (PG16)
12
1
1605210
Power cable 4 x 1.5mm
13
2
1031503
Silicon hose cold complete
14
4
140339
Clip for hose 16.4mm
15
2
1205101
Brewing elemnet 230V/2200W
16
2
1505062
Overflow tube
17
1
1206123
Non return valve
18
1
160549
Connector fv122
19
2
1204016
Spray nozzle for water tank
20
6
160536
Gasket rubber NBR(Rubber Trp 30.0)
21
2
1204014
Microswitch holder
22
2
160821
Micro switch tank 1.8L
23
2
1505063
Bottom cover rubber
24
4
120320
Rubber feet V2
25
4
1402163
Screw M4x8
26
4
120811
Warming plate 230V/95W
27
1
160101
Heat coil 95W
28
1
1603855
Overlay original M
29
1
160804-04
Brewing lamp
30
1
160802-04
Rocker switch double
43
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Mega Gold A
Drawing
1
25
2
26
24
3
11
23
31
8
9
4
7
30
6
10
5
14
21
12
22
29
18
17
13
16
19
15
27
20
28
44
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Mega Gold A
Spare parts list
POS.
PCS
Part No.
Description
1
1
1204012
Lid
2
1
1204013
Strainer
3
1
1204015
Water tank complete 1.8L
4
1
1204016
Spray nozzle for water tank
5
4
140339
Clip for hose 16.4mm
6
1
1505041
Siliocn hose hot W 1.8L
7
1
1205101 (230V)
Brewing element 230V/2200W
7
1
120505 (110V)
Brewing element 110V/1600W
8
1
160212-03
Over heating protection
9
1
1206123
Non return valve 1.8L
10
1
160821 (230V)
Micro switch tank 1.8L
10
1
1608221 (110V)
Micro switch 125V
11
1
1505062
Overflow hose 1.8L
12
1
1031640 (230V)
Electronic unit PCB Original
12
1
1031643 (110V)
Electronic unit PCB Original 110V
13
1
160801-04
Rocker switch single(orange)
14
1
1031503
Silicon hose cold complete
15
1
1603854
Membran switch origi A
16
1
1103303
Serving station 2.5L
17
1
160570
Power cord inlet/ Main socket
18
1
120620-01 (230V)
Valve inlet single 1.8L
18
1
120617 (110V)
Inlet coil 110V
19
1
1505063
Bottom cover rubber
20
4
120320
Rubber feet
21
1
1102016
Brew basket 1.8L
22
6
160536
Gasket rubber NBR(Rubber Trp 30.0)
23
1
1505042
Inlet hose 3/4”-1/2”
24
1
1206603
Gasket DIA23.5mm x 15mm D3mm
25
1
1206604
Gasket DIA18mm x 9mm D2mm
26
1
2760094
Gasket set for inlet hose
27
1
160565
Main supply cable / Europe
28
4
1402163
Screw M4x8
29
Sale in M
150501
Silicone tube 8x12mm
30
1
1204014
Microswitch holder
31
1
1402150
Screw T20,M4X8mm
45
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Mega Gold M
Drawing
1
2
3
9
4
12
5
10
6
13
14
11
7
15
8
16
18
20
19
17
23
22
46
24
25
21
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Mega Gold M
Spare parts list
POS.
PCS
Part No.
Description
1
1
1204012
Lid
2
1
1204013
Strainer
3
1
1204015
Water tank complete 1.8L
4
1
1505062
Overflow hose 1.8L
5
1
160212-03
Over heating protection
6
1
1205101 (230V)
Brewing element 230V/2200W
6
1
120505 (110V)
Brewing element 110V/1600W
7
1
1031503
Silicon hose cold complete
8
1
1102016
Brew basket 1.8L
9
1
1402150
Screw T20, M4X8mm
10
1
1204016
Spray nozzle for water tank
11
1
1505041
Siliocn hose hot W 1.8L
12
1
1204014
Microswitch holder
13
1
1206123
Non return valve 1.8L
14
1
160821 (230V)
Microswitch tank 1.8L
14
1
1608221 (110V)
Micro switch 125V
15
4
140339
Clip for hose 16.4mm
16
6
160536
Gasket rubber NBR(Rubber Trp 30.0)
17
1
1603855
Overlay original M
18
1
1505063
Bottom cover rubber
19
1
160570
Power cord inlet/ Main socket
20
1
160801-04
Rocker switch single
21
1
160804-04
Brewing lamp
22
1
1103303
Serving station 2.5L
23
4
120320
Rubber feet
24
4
1402163
Screw M4x8
25
1
160565
Main supply cable / Europe
47
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Thermos Office
Drawing
2
Tank
Float
Strainer
Cover
Microswitch holder
3
4
5
1
6
8
7
9
10
11
12
13
14
16
15
17
18
19
22
23
21
48
20
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Thermos Office
Spare parts list
POS.
PCS
Part No.
Description
1
1
1102016
Brew basket 1.8L 90 mm
2
1
1204012
Lid of tank original
3
1
1204013
Strainer original
4
1
1204015
Water tank complete 1.8L
5
1
160821 (230V)
Micro switch tank 1.8L
5
1
1608221 (110V)
Micro switch 125V
6
1
1204014
Microswitch holder
7
1
1505062
Over flow hose 1.8L
8
1
1505041
Silicon hose hot 1.8L
9
1
1204016
Spray nozzle for water tank
10
2
1402150
Screw T20,M4X8mm
11
1
120422
Air inlet plastic 1.8L
12
1
160212-03
Over heating protection
13
1
1205101 (230V)
Brewing element 230V/2200W
13
1
120505 (110V)
Brewing element 110V/1600W
14
4
140339
Clip for hose 16.4mm
15
1
1031503
Silicon hose cold complete
16
1
160565
Main supply cable / Europe
17
1
160570
Power cord inlet / Main socket
18
1
160804-04
Brewing lamp
19
1
160801-4
Rocker switch single
20
1
1103256
Thermos 1.9L
21
1
1505063
Rubber bottom TPE
22
4
120320
Rubber feet V2
23
4
1402163
Screw M4x8
49
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Thermos A
Drawing
1
2
9
Tank
Float
Strainer
Cover
Microswitch holder
3
10
11
6
4
5
15
12
16
17
7
13
18
19
14
8
20
22
21
23
24
25
26
50
27
28
29
30
31
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Thermos A
Spare parts list
POS.
PCS
Part No.
Description
1
1
1204012
Lid of tank original
2
1
1204013
Strainer original
3
1
1102016
Brew basket 1.8L 90 mm
4
1
1206604
Gasket DIA18mm x 9mm D2mm
5
1
1206603
Gasket DIA23.5mm x 15mm D3mm
6
1
2760094
Gasket set for inlet hose
7
1
1505042
Inlet hose 3/4”-1/2”
8
1
1103184
Thermos 2.2L
9
1
1204015
Water tank complete 1.8L
10
1
160821 (230V)
Micro switch tank 1.8L
10
1
1608221 (110V)
Micro switch 125V
11
1
1204014
Microswitch holder
Overflow hose
12
1
1505062
13
Sale in M
150501
Silicone tube 8x12mm
14
1
120620-01 (230V)
Valve inlet single 1.8L
14
1
120617 (110V)
Inlet coil 110V
15
1
1505041
Hot water hose 1.8L
16
1
1204016
Spray nozzle for water tank
17
2
1402150
Screw T20,M4X8mm
18
1
120422
Air inlet plastic 1.8L
19
1
160212-03
Over heating protection
20
1
1205101 (230V)
Brewing element 230V/2200W
20
1
120505 (110V)
Brewing element 110V/1600W
21
1
140339
Clip for hose 16.4mm
22
1
1031503
Silicon hose cold complete
23
1
1031640 (230V)
Electronic unit PCB Original
23
1
1031643 (110V)
Electronic unit PCB Original 110V
24
4
120320
Rubber feet V2
25
4
1402163
Screw M4x8
26
1
1505063
Bottom rubber TPE
27
6
160536
Gasket rubber NBR(Rubber Trp 30.0)
28
1
160801-04
Rocker switch single(orange)
29
1
160570
Power cord inlet/Main socket
30
1
1603854
Membran switch Original A
31
1
160565
Main supply cable / Europe
51
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Thermos M
Drawing
1
4
2
Tank
Float
Strainer
Cover
Microswitch holder
5
3
6
7
8
10
9
11
13
12
14
15
16
17
18
19
52
20
21
22
23
24
25
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Thermos M
Spare parts list
POS.
PCS
Part No.
Description
1
1
1204012
Lid of tank original
2
1
1204013
Strainer original
3
1
1102016
Brew basket 1.8L 90 mm
4
1
1204015
Water tank complete 1.8L
5
1
160821 (230V)
Micro switch tank 1.8L
5
1
1608221 (110V)
Micro switch 125V
6
1
1204014
Microswitch holder
7
1
1505062
Overflow hose
8
1
1505041
Hot water hose 1.8L
9
1
1204016
Spray nozzle for water tank
10
2
1402150
Screw T20,M4X8mm
11
1
120422
Air inlet plastic 1.8L
12
1
1103184
Thermos 2.2L
13
1
160212-03
Over heating protection
14
1
1205101 (230V)
Brewing element 230V/2200W
14
1
120505 (110V)
Brewing element 110V/1600W
15
1
140339
Clip for hose 16.4mm
16
1
1031503
Silicon hose cold complete
17
4
120320
Rubber feet V2
18
4
1402163
Screw M4x8
19
1
1505063
Bottom rubber TPE
20
6
160536
Gasket rubber NBR(Rubber Trp 30.0)
21
1
160804-04
Brewing lamp
22
1
160801-04
Rocker switch single(orange)
23
1
160570
Power cord inlet/Main socket
24
1
1603855
Overlay original M
25
1
160565
Main supply cable / Europe
53
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Cater
Drawing
1
5
6
27
2
3
4
7
8
9
10
11
12
16
17
13
14
15
26
22
18
54
19
20
21
23
24
25
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Cater
Spare parts list
POS.
PCS
1
1
1102011
Brew basket 110mm
2
1
1664002
Red indicating lamp 230V
3
1
1603863
Membrane switch single
3
1
1603864
Membrane switch double
4
1
1201924
Hot water faucet
5
1
140204
Screw M4x6mm
6
1
1505042
Inlet hose 3/4”-1/2”
7
1
1604203/1604201
Solid state 25A
8
1
120624-01 (230V)
Valve inlet single 2.5L
8
1
120617-01 (110V)
Inlet coil 110-120V
9
1
1403401
Inlet valve plug with silicon seal
10
1
160571
Emi fliter with ac socket
11
1
160801-04
Rocker switch single(orange)
12
1
1206581
Seal solid state
13
1
160351
Connecter PA80 FF
14
1
1605651
PG complete (P16)
15
1
1605210
Power cable 4x1.5mm
16
1
1603866
Overlay cater without hole
17
1
1031801
Spray nozzle tower
1103303
Serving station 2.5L
18
Part No.
Description
19
1
160970
CQ sticker
20
1
1605403
Flat cable, extention
21
4
120136
Adjustable feet
22
1
1031646 (230V)
Electronic unit PCB Cater
22
1
1031645 (110V)
Electronic unit PCB 110V Cater
23
1
1603865
Overlay cater with hole
24
1
1206603
Gasket DIA23.5mm x 15mm D3mm
25
1
1206604
Gasket DIA18mm x 9mm D2mm
26
1
2760094
Gasket set for inlet hose
27
1
120422
Air inlet plastic 1.8L
55
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Cater tank
Drawing
1
11
12
13
2
3
15
4
16
14
10
5
17
18
19
6
20
7
8
9
27
21
22
24
25
26
56
23
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Cater tank
Spare parts list
POS.
PCS
Part No.
Description
1
1
1401101-01
Nut M3
2
1
1461008
Spring washer M3
3
1
1205305
Sensor pin 47mm
4
1
1205303
Sensor pin long 160mm
5
2
1605362
Double seal level sensor
6
1
1031505
Hot water tube
7
1
711000
Ntc thermistor belong
8
1
1605361
Seal for NTC
9
1
1031502
Overflow tube Double Cater
10
1
1031506
Steam hose
11
1
1031504
Outlet tube cater
12
1
1402220
Screw M5x20
13
1
220221
High limit switch
14
2
1206507
Fiber washer element
15
1
1206505
Gasket HL switch
16
1
250430
Tank lid bracket
17
1
250433
Lid washer
18
1
1206587
Tank gasket
19
1
1601311 (230V)
Element 2200W/230V with ss nuts
19
1
1601310 (110V)
Element 1600W/120V
20
2
160538-03
Plug for water outlet
21
2
1206123
Non return valve
22
2
1364004
Clamp spring steel
23
Sale in M
1561009
Silicone tube braided 1m ID-9.53mm
24
1
160193
PDS valve
25
1
1403400
Pp plug for drainage hose
26
4
140339
Clip for hose 16.4mm
27
Sale in M
150501
Silicone tube 8x12mm
57
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Tower
Drawing
10 11 12 13 14
6
1
7
3
15
50
9
4
16
17
5
2
18
19
8
25
20
26
32
21
22
23
33
32
24
31
27
28
35
29
30
36
37
41
42
34
38
39
45
43
40
44
46
58
47
48
49
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Tower
Spare parts list
POS.
PCS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
29
30
31
32
33
34
35
36
37
37
38
39
40
41
42
43
44
45
46
47
48
49
50
4
2
1
2
2
6
1
1
2
1
1
1
2
2
1
1
10
1
2
5
Sale in M
5
2
1
2
1
1
3
3
3
2
1
6
1
1
1
1
1
1
4
1
1
1
1
1
1
1
2
1
1
1
1
Part No.
1102122
1103302
1305011
1561028
1031801
1206503
1601312
711000
1561010
1205302
1461008
1401101-01
1205301
1605362
1206586
220220
140225
1203526
160230
140330
150501
140339
1403400
1206123
1605361
1031502
160351
1605361
1604203/1604201
1604204
1104330
1608017
1402163
1505076
1802120
120200-02
1031642
1603856
1603859
120316
1602231
160429-02
1605241
1605651
1206603
1206604
2760094
1102131
1505042
120634
1604393
160538-03
Description
End cover
Serving station 5L
OH bulb holder
Silicon outlet tube
Spray nozzle Tower
Fiber washer
Element 3000W
NTC thermistor
Seal for outlet valve
Sensor short (55mm)
Spring washer M3
Nut M3
Sensor long (90mm)
Double seal level sensor
Gasket tank tower
High limit switch
Tank lid screw M4x12mm
Tank Tower complete
Solenoid valve oulet 230V
Clamp 13.3mm
Silicon hose 8x12mm
Clip for hose 16.4mm
Pp plug for drainage hose
Non return valve
Seal for NTC
Tube for overflow
Connecter PA80 FF
Seal for solid state
Solid state 25A
Solid state 50A
Drip cup
Power switch (black)
Screw M4X8mm
Rubber Plug, 10mm black
Connection faucet short
Faucet metal black top
Electronic unit PCB Tower
Membrane switch, Tower
Membrane switch, Single Tower
Adjustable foot
Relay 230V VAC
Fuse automatic
Power cord 3-phase 5x2.5mm(1.8m)
PG complete (PG16)
Gasket DIA23.5mm x 15mm D3mm
Gasket DIA18mm x 9mm D2mm
Gasket set for inlet hose
Brewbasket 5L
Inlet hose 3/4”-1/2”
Valve single 5L/min
Electronic filter
plug for water outlet
59
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Grinder original
Drawing
1
2
3
4
5
6
6
7
8
11
13
14
9
16
12
15
17
10
18
19
28
20
21
23 24
60
25
26
27
29
30
31
32
33
34
22
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Grinder original
Spare parts list
POS.
PCS
Part No.
Description
1
1
1364001
Finger Protection
2
1
1608281
Magnet 39x13x6mm
3
1
1364002
Metal Plate for finger protection
4
1
1105517
Bean Hopper
5
1
1031647
Electronic unit PCB Grinder
6
9
140204
Screw M4x6
7
1
1561004
Sealing Rbbber
8
1
1604752
Grinder EK-21
9
1
1204651
Rubber trp 40
10
1
1605652
Power cable fixed 16A 250V
11
1
1264027
Nylon washer 8mm
12
1
1461038
Screw M4x6 with step
13
1
83243641
Silicone flap
14
1
1561003
Outlet tube sealing
15
1
1264009
Nylon base Grinder
16
1
1561002
Base silcon Grinder
17
4
1561005
Nylon Bushing
18
1
1461005
Screw M4x40
19
2
1264013
Nylon Slide Guide
20
1
83257335
Capacitor
21
1
160245
Relay 230V C7-A20
22
1
160247
Chassi adapter
23
1
1505076
Rubber Plug,10mm black
24
1
1608017
Rocker Switch Black
25
1
1603854
Membran switch original
26
1
1608131
Adjustment wheel 20mm
27
1
1608132
Cover lid 20mm
28
1
710553
Adjustment kit
29
1
1461019
Spring link 14cm
30
1
1401901
Screw M4x16
31
1
1402163
Screw M4x8mm
32
1
120320
Rubber Feet
33
1
160351
Connecter PA80 FF
34
1
160246
Socket V-7 relay
61
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Grinder EK21
Drawing
07
08
09
01
10
02
11
03
04
05
06
12
20
13
12
14
21
19
15
16
17
18
Grinding disc service pack
62
22
23
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Grinder EK21
Spare parts list
POS.
PCS
Part No.
Description
1
1
83230921
Motor 200-240V/50/60Hz
2
1
83250823
Allen screw, M4x4
3
1
83230939
Bean inlet housing EK21
4
1
83255509
O-Ring 35x4
5
3
83250822
Cylinder screw, M4x50
6
1
83230928
Conveying screw EK21
7
1
83250821
Slotted head screw, M4x16
8
1
83243678
Pressure spring
9
1
83307991
Adjustment pinion
10
1
83250742
Allen set screw, DIN916-M5x10
11
1
83243677
Adjustment shaft
12
1
83306715
Grinder discs EK21 (service pack)
13
4
83250614
Slotted head screw
14
1
83230926
Grinding disc carrier - rotating
15
1
83251601
Washer, 10x16x1
16
1
83251043
Hexagon nut left hand thread-M8L-08d
17
3
83250408
Slotted head screw, M4x14
18
1
83100914
Grinder Housing
19
1
83250743
Allen set screw, DIN916-M4x5
20
1
83243641
Silicone flapper for grinder
21
1
83243642
Coffee outlet spout
22
1
140335
Tube clamp 19.2 mm
23
1
1505081
Silicon hose ID16 OD19mm
63
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
HVA\HVM
Drawing
11
12 13
14
15
19
20
16
18
17
1
2
25
21
22
3
26
23
24
36
37
4
38
5
39
6
40
28
29
30
7
31
8
32
9
33
10
34
35
64
27
41
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
HVA\HVM
Spare parts list
POS.
PCS
Part No.
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
2
1
1
1
1
1
1
3
Sale in M
1
1
1
4
1
1304061
1031301
1304062
160970
1802120
120200-02
1031641
1603853
253207
1304063
220221
1206589
1205303
1205302
1505042
1206604
1206603
2760094
120422
1402150
1401101-01
1461008
1605362
1203527
1206507
1601311
1605361
1206123
140330
150501
1403400
1206581
1604203/1604201
120320
1402163
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
Description
Lid plastic HVA
HVA lid
Top plastic HVA
CQ sticker
Connection faucet short
Faucet metal black top
Electronic unit PCB HVA
Membrane switch HVA
Drip tray insert
Drip tray HVA
High limit switch short with connect
Gasket tank
Sensor HVA tall(160mm)
Sensor short (55mm)
Inlet hose 3/4”-1/2”
Gasket DIA18mm x 9mm D2mm
Gasket DIA23.5mm x 15mm D3mm
Gasket set for inlet hose
Air vent
Screw T20 M4x8mm
Nut M3
Spring washer M3
Double seal level sensor
Tank complete HVA
Fiber washer
Element 2200W/230V with SS nuts
Seal NTC
Non return valve
Clamp 13.3mm
Silicon hose 8X12mm
PP plug for drainage hose
Seal solid state
Solid state 25A
Rubber feet V2
Screw T20 M4x8mm
36
1
1403401
Inlet valve plug with silicon seal
37
1
160801-04
Rocker switch single
38
1
160571
Emi fliter with AC socket
39
1
120624-01
Single valve 2.5L/min
40
1
711000
NTC thermistor belong
41
1
160565
Power cord european 16A250V
65
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
V-2
Drawing
1
2
8
3
4
9
5
9
6
7
Spare parts list
POS.
PCS
1
2
160101
Heat coil 95W
2
2
120811
Warming plate 230V/95W
3
2
160536
Gasket rubber NBR(Rubber TRP 30.0)
4
1
2401101
Chassi V-2
5
1
1605652
Power cable fixed 16A 250V
6
6
120320
Rubber Feet
7
6
1402163
Screw M4x8mm
8
1
160970
CQ sticker
9
2
1608017
Power Switch Black
66
Part No.
Description
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Serving station 2.5L
Drawing
1
2
14
8
9
10
3
15
16
4
5
11
12
6
7
13
7
67
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Serving station 2.5L
Spare parts list
POS.
PCS
Part No.
1
1
1103351
Lid Cover with Tie
2
1
1103452
Brew-Thru Lid with SS Tube (2.5L)
3
1
1103453
Main housing with Upp 2.5L
4
1
1103455
Lower Housing 2.5L
5
1
1103456
Outlet Tube Jacket (2.5L)
6
1
1103457
Stand 2.5L
7
5
1103364
Rubber feet
8
1
1103459
Glass Tube (2.5L serving station)
9
1
1103360
Cleaning Brush for Level Indicator
10
1
1103461
Water Indicator Lens (2.5L)
11
1
1103462
Outlet Tube (2.5L serving sation)
12
1
1103363
Faucet, Crown
13
1
1103458
Drip Tray (2.5L serving station)
14
1
1103371
Display Top Serving Station.2.5L
15
1
1103303
Serving Station 2.5L
16
1
1103366
Outlet Connector 2.5L Servn.stn
68
Description
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Serving station 5L
Drawing
1
17
2
14
8
9
10
3
15
16
4
5
11
12
6
7
13
7
69
EXPLODED VIEW
FILTERBREW & SERVING CONCEPT
Serving station 5L
Spare parts list
POS.
PCS
Part No.
1
1
1103351
Lid Cover with Tie
2
1
1103352
Brew-Thru Lid with SS Tube (5L)
3
1
1103353
Main Housing with Upper Housing
4
1
1103355
Lower Housing 5L
5
1
1103356
Outlet Tube Jacket (5L)
6
1
1103357
Stand
7
5
1103364
Rubber feet
8
1
1103359
Glass Tube (5L serving station)
9
1
1103360
Cleaning Brush for Level Indicator
10
1
1103361
Water Indicator Lens (5L)
11
1
1103362
Outlet Tube (5L serving sation)
12
1
1103363
Faucet, Crown
13
1
1103358
Drip Tray (5L serving station)
14
1
1103370
Display Top Serving Station 5L
15
1
1103302
Serving Station 5L
16
1
1103365
Outlet Connector 5L Servn.stn
17
1
1103354
SS Vacuum Bottle, Silicone gasket
70
Description
DIMENSION
FILTERBREW & SERVING CONCEPT
A-2/M-2
A
D
E
F
B
C
Model
A
B
C
D
E
F
A-2/M-2
595mm
205mm
410mm
428mm
578mm
360mm
71
DIMENSION
FILTERBREW & SERVING CONCEPT
DA-4/DM-4
E
D C
F
B
A
Model
A
B
C
D
E
F
DA-4/DM-4
410mm
410mm
428mm
595mm
578mm
360mm
72
DIMENSION
FILTERBREW & SERVING CONCEPT
Thermos A/M
A
D
F
C
B
Model
A
B
C
D
F
Thermos A/M
557mm
205mm
410mm
708mm
360mm
73
DIMENSION
FILTERBREW & SERVING CONCEPT
Mega Gold A/M
E
A
B
D
C
Model
A
B
C
D
E
Mega Gold A/M
655mm
205mm
445mm
390mm
806mm
74
DIMENSION
FILTERBREW & SERVING CONCEPT
Single Tower
C
D
E
A
G
F
B
Model
A
B
C
D
E
F
G
Single Tower
934mm
610mm
500mm
174mm
410mm
233mm
244mm
75
DIMENSION
FILTERBREW & SERVING CONCEPT
Tower
B
C
D
E
A
G
F
Model
A
B
C
D
E
F
G
Tower
934mm
928mm
500mm
174mm
410mm
233mm
244mm
76
DIMENSION SKETCH
FILTERBREW & SERVING CONCEPT
Single Cater/ Tea Cater
A
E
D
B
C
Model
A
B
C
D
E
Single Cater/Tea Cater
690mm
205mm
450mm
105mm
436mm
77
DIMENSION SKETCH
FILTERBREW & SERVING CONCEPT
Cater
Brewing
Brewing
A
E
D
B
78
C
Model
A
B
C
D
E
Cater
690mm
410mm
450mm
105mm
436mm
DIMENSION
FILTERBREW & SERVING CONCEPT
Serving station 5L
B
C
A
D
E
Model
A
B
C
D
E
Serving station 5L
483mm
373mm
325mm
449mm
110mm
79
DIMENSION
FILTERBREW & SERVING CONCEPT
Serving station 2.5L
A
C
D
E
B
Model
A
B
C
D
E
Serving station 2.5L
205mm
273mm
436mm
400mm
105mm
80
DIMENSION
FILTERBREW & SERVING CONCEPT
V-2
C
A
D
B
E
Model
A
B
C
D
E
V-2
62mm
359mm
230mm
189mm
198mm
81
DIMENSION
FILTERBREW & SERVING CONCEPT
HVA/HVM
B
D
A
E
C
Model
A
B
C
D
E
HVA/HVM 1 phase
500mm
225mm
410mm
240mm
210mm
HVA/HVM 3 phase
500mm
225mm
410mm
240mm
210mm
82
DIMENSION
FILTERBREW & SERVING CONCEPT
Grinder Original
A
C
B
Model
Grinder Original
D
A
B
C
D
570mm
215mm
368mm
390mm
83
For the warranty to be valid the conditions for maintenance must have been
followed according to our instructions, proper precaution has been made and
warranty claim been issued without delay.
The affected equipment may not be used during awaiting service if there is any risk
that the damage or defect would worsen.
The warranty will not cover consumption supplies such as glassware, normal
maintenance such as cleaning of filters, contaminations in water, lime, incorrect
voltages, pressure or adjustment of water amounts.
The warranty will not cover damages of defects caused by incorrect handling and
operation of the appliance.
FOR SERVICE
Please contact your dealer
Your Dealer
www.creminternational.com
Download PDF
Similar pages