Please read the following instructions and warnings carefully.
Keep this instruction manual for future reference.
Tools required (for wall mouting Camera only): Screwdriver and Drill (not included)
For technical support see back page.
Adult use only.
WARNING:
Adult assembly required. Keep small parts
away from children when assembling.
®
®
INSTRUCTION MANUAL
Warnings & Guidelines:
WARNING:
STRANGULATION HAZARD - Keep cord
out of baby’s reach. NEVER place Camera
or cords within 3 feet of the crib. Use enclosed Security Clips to help secure
cord away from baby’s reach. Never use extension cords with AC Adapters.
Only use the AC Adapters provided. Do not remove this tag.
1
Warnings & Guidelines • Continued
WARNING:
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION.
• STRANGULATION HAZARD - Keep cord out of baby’s reach.
NEVER place camera or cords within 3 feet of the crib. Use enclosed Security
Clips to help secure cord away from baby’s reach. Never use extension cords
with AC adapters. Only use the AC adapters provided.
• When an AC adapter is plugged into an electrical outlet, do not touch the
exposed end.
• Test monitor before first use, periodically, and when changing location of
the Camera.
• Do not use monitor near water (such as bathtub, sink, etc.).
• Keep monitor away from heat sources (such as stoves, radiators, etc.).
• Make sure there is proper ventilation around all monitor components. Do
not place on sofas, cushions, beds, etc. which may block ventilation.
• Nursery monitors use public airwaves to transmit signals. This monitor may
pick up signals from other monitors or similar devices and signals broadcast
by this monitor may be picked up by other receivers.
• This product is not a toy. Do not allow children to play with it.
• This product contains small parts. Adult assembly required. Exercise care
when unpacking and assembling the product.
BATTERY WARNING:
• Use only the original rechargeable batteries provided. Please contact Baby
Delight, Inc. for replacement batteries. Contact information can be found
on bottom of these instructions or on the battery itself.
• Do not mix old and new batteries.
• Do not mix alkaline, standard, or rechargeable batteries.
• Batteries are to be inserted with correct polarity.
• Clean battery and product contacts prior to battery installation.
• Do not short-circuit supply terminals.
• Only the recommended batteries or equivalent are to be used, volts
and size.
• Remove the batteries when product is stored for long periods of time or
when batteries are exhausted.
• Dispose of exhausted batteries properly.
• Do not recharge non-rechargeable batteries.
• Rechargeable batteries are only to be charged under adult supervision.
• Keep all batteries away from children.
2
All Components
• 1 Camera, 1 Monitor, 1 Movement Unit
• 2 AC Adapters
• 6 Cable Clips
• 1 Anchor and Wall Mount Screw
Camera
Movement
Unit
®
AC Adapters
Hardware
X1
®
X1
X6
Monitor
Features • Camera
Power On LED
Lens
Microphone
Movement Unit Charging Station
(Place Movement Unit in this to charge)
Power On/Off
AC Adapter Jack
3
Features • Monitor
Menu
Pause Alarm
Talk Back
Power On/Off
Video On/Off
Volume
Toggle Left/Right
Sound/Lights
Power LED
LED Battery Indicator
OK/Select/Zoom
®
Speaker
Microphone
Brightness
Toggle Up/Down
(Underneath)
Magnetic Clip for
Clothing
®
Adjustable
Kickstand
Battery
Compartment
AC Adapter
Plug
Power Button
4
Camera Setup • Adult Assembly Required
There is no need to pair any of
the components. The Camera,
Monitor and Movement Unit
have all been synched at
the factory. If for any reason
pairing is lost, please refer to
TROUBLESHOOTING section
on page 9.
2
Plug AC
Adapter with
Camera Icon
into Camera
CAMERA PLACEMENT : ON FLAT SURFACE
1 TABLE TOP: Place Camera in desired location, plug
in AC Adapter to Camera and turn on.
WARNING: 3 FT
IMPORTANT
at least
3ft
from crib
UG
PL
IN
Be sure to
test reception
and camera
positioning.
Determine a location for the Camera that will
provide the best view of your baby in the crib. Place
the Camera on a flat surface, such as a dresser,
bureau or shelf. NEVER place Camera or cords within
3 feet of the crib. Be sure to test reception and
Camera positioning.
CAMERA PLACEMENT: IF WALL MOUNTING
1 Place Camera in
desired location.
Pre-drill a hole in
the wall using 3/16”,
4.8mm, drill bit.
(Drill bit and drill not
included).
2
mount at
least
IMPORTANT
3ft
from
crib
5
3
4
Tighten screw until only 1/4” (6.3mm)
of the screw is exposed (screw driver
1/4”
not included).
5
Secure the cord to
the wall using the 6
Security Clips included
to keep cord away from
baby’s reach.
UG
PL
at least
3ft
IMPORTANT
Be sure to
test reception
and Camera
positioning.
IN
Monitor Setup • Adult Assembly Required
Plug Monitor AC Adapter into
Monitor and hold the power button
on top of Monitor for 5 seconds.
ON
Be sure to test your Monitor’s reception before initial use.
We also recommend testing your Monitor’s reception periodically.
PLEASE KEEP IN MIND THAT THE MOVEMENT & POSITIONING VIDEO
MONITOR WILL NOT PROVIDE THE SAME LEVEL OF PICTURE QUALITY AS
YOUR TELEVISION WITH CABLE, SATELLITE DISH, OR DIGITAL SERVICE.
®
Movement Unit Setup • Adult Assembly Required
The Movement Unit will transmit movement info and baby’s orientation (side,
stomach and back) to the Camera. The Camera will transmit this information to
the Monitor and display that information on the screen. For best results, make
sure the Movement Unit is within 30 feet of the Camera.
6
Max 30 Feet
Max 600 Feet
Movement &
Positioning Data
1 Press the power button on the center top of the Movement Unit for 4
seconds to power on. You should see movement info and orientation of
the baby (side, back, stomach) on the monitor screen.
SIDE
100%
STOMACH
Press power on the
movement unit until you
hear a beep.
BACK
®
Research shows that sleeping
on their back is the safest
position for babies.
®
2 ATTACHING MOVEMENT UNIT: Place the top of the
Movement Unit with logo facing UP over baby’s
clothing and then slip the magnetic bottom unit
behind the clothing with the magnets
away from baby.
®
®
The two pieces should
connect together with the
clothing in the middle.
NOTE: FOR BEST RESULTS, THE WEARABLE UNIT SHOULD BE PLACED ON A
SNUG-FITTING ONESIE ON THE CENTER OF THE BABY’S CHEST.
The Movement Unit will flash every 10 seconds:
Green: Full Battery
Amber: Charge Soon
Red: Low Battery - Charge Immediately
7
Movement Unit Icon Status • On Monitor Screen
Charging Icon – This means the Movement Unit is currently in
the recharging dock in the Camera and is charging. Movement &
orientation information is disabled. The Movement Unit will flash
Low
an amber or red light every 4 seconds while charging. When
fully
Battery
charged the light will turn green.
Charging
Si
Low Battery Icon – This means the Movement Unit needs to be
charged. The Movement Unit will flash a red light. The Movement
Unit can be re–charged on the Camera (takes approximately
6 hours) in the dock. The Movement Unit has a battery life of
approximately 96 hours of continuous use.
Low
Battery
C
No Signal Icon – This means the Movement Unit is out of range
or powered off while not charging in the dock. Please locate the
Movement Unit and place it in the charging dock
Camera or
Lowon theCharging
move the Movement Unit closer to the Camera.
Battery
No
Signal
D
Disabled Icon – This means the user has disabled the Movement
Unit. You can choose NOT to show the movement info and position
info on the Monitor screen. This also disables all alarms on the
Monitor. The Movement Unit will
still alarm
if no movement No
is
Low
Charging
detected for 15 seconds.
Battery
Signal
Disable
To Disable the Movement & Orientation Information
To disable the movement and orientation information from being displayed on
the screen, use the following steps. PLEASE NOTE: This also disables all alarms on
the Monitor.
Press the Menu button on the Monitor.
Locate the Monitor icon and use
the RIGHT button to move to the
DISPLAY ICON and press OK.
menu
left/right
ok
100%
Screen will display TURN MOVEMENT
INFO AND ALARM OFF. Use the LEFT/
RIGHT button to select ON or OFF and
press OK.
ok
100%
Turn Movement
Info and Alarm
ON
OFF
®
OFF
®
8
Alarm Icon – After no movement has
been detected for 15 seconds, the
Monitor will begin to beep. After 20
seconds of no movement detected,
the Alarm icon will appear on the
Monitor screen and the Monitor will
beep rapidly.
pause alarm
be
Pause Icon – Pressing the Pause
button on the Monitor when the Alarm
Icon is on the screen and the Monitor
is alarming will silence the Alarm for
15 seconds. After 15 seconds, if there is
still no movement detected, the alarm
will resume. Note: The alarm can also
be paused if there is any movement
of the Movement Unit.
ep
100%
PRESS PAUSE BUTTON
AND CHECK MOVEMENT
Paused
®
®
If the Camera is disconnected from the power source while Movement Unit is in
charging station, please power OFF the Movement Unit to avoid an alarm.
Troubleshooting
The Camera, Monitor and Movement Unit have all been paired at the factory.
If any of the components need to be re-paired, please see below:
To Re-Pair the Camera and Monitor:
1
Place the Monitor
and Camera within 3
feet of each other and
power on both units.
3ft
®
2 Press the MENU button on the
Monitor and use the RIGHT
or
LEFT
button to move to the CAMERA
icon. Press the OK button to start pairing.
menu
3 You should see the PAIRING
SCREEN that will appear for
20 seconds.
left/right
100%
ok
100%
Pairing
®
®
9
4
With the Camera powered ON,
press the CODE button on the
bottom of the Camera.
5 You should see live video on
the Monitor.
code
button
100%
®
To Re-Pair the Movement Unit and Camera:
1 Place Monitor and
Movement Unit within
3 feet of each other.
Power off the Movement
Unit (hold the POWER
button for 4 seconds)
and power on the
Camera.
OF
2
Press the MENU button on the Monitor and
use the RIGHT or LEFT button to move to
the Movement Unit icon.
menu
left/right
100%
F
®
®
3 Press the OK button and you
should see the PAIRING SCREEN
that will appear for 20 seconds.
ok
4 Power the Movement Unit on
(hold the POWER button for 3
seconds). You should see movement
and orientation information on
the Monitor.
ON
®
100%
100%
Pairing
®
®
10
Limited Warranty
At Baby Delight, Inc. we make innovative and high quality products for babies,
children and their parents. We warrant this product to be free from defects in
material and workmanship existing at the time of manufacture for a period of
one year from the date of initial purchase (sales receipt is required for proof of
purchase). If such a defect is discovered during the limited warranty period, we
will, at our sole option, repair or replace your product at no cost to you.
This limited warranty does not cover claims resulting from misuse, failure to
follow the instructions on installation, maintenance and use, abuse, alteration,
involvement in an accident, and normal wear and tear.
For warranty service or replacement part information:
USA: Please call 1-401-333-6800, or write to Consumer Services, 30 Martin St.
Cumberland, RI 02864
Some replacement parts may be available for purchase after this limited warranty
expires. Please visit us at www.babydelight.com or call us at 1-401-333-6800
for details.
11
www.babydelight.com
info@babydelight.com
Macari Baby, Inc. 401-333-6800
30 Martin Street, Cumberland, RI 02864
MADE IN CHINA
BD04020, BD04010
12
Download PDF
Similar pages