Western Red Cedar Cooler
(32” x 21” x 35”) Assembly Instruction
1
Item #: CC24-32
Parts Identification
Stack matching pieces in piles. Using the parts list, locate and count
the individual pieces and verify that you have received the correct
number of pieces.
1
2
If any pieces are missing or replacement parts are required,
contact Gronomics at 1-855-299-6727.
NOTE: It is recommended to place a protective layer between
the ground and the pieces during assembly. This will help prevent
damage to the pieces.
Torx® T15
4
Parts List
Parts List
PART #
DESCRIPTION
ITEM
QTY.
1
1
2
4
3200CL
3
1
4
24
CCBO
CS8-112ZY
2
3
CC2432
Product Care & Maintenance
Western Red Cedar will turn a weathered grey if
left unfinished. Although no finish is required for
cedar products when used outdoors,a natural oil
finish applied regularly will help maintain the
beauty and minimize cracking and drying. It is
recommended to use Gronomics Garden Bed
Oil (Item # GBO-1Q), a non-toxic, food safe
finish that is very easy to apply.
Western Red Cedar Cooler, 20” x 30”
Cooler Legs, 32”
Bottle Opener
Screws, #8 x 1-1/2”GRK use Torx T15
Cooler Leg Assembly
Open Cedar
Cooler Cover
NOTE: Place a protective layer on the ground for leg installation.
Remove the plastic cooler bottom from the cedar cooler.
Place the cedar cooler (Item 1) on its side on the ground (as shown).
Open the cedar cooler cover.
1
Pace two cooler legs (Item 2) under each side of the cooler (with the
straight cut end of the leg flush at the top of the cedar cooler and the
beveled cut end of the leg down.
2
Remove The Plastic Cooler
2
Beveled End Of Leg
Packaged & Inspected by:
Date:
Continued
www.gronomics.com
East Bethel, MN USA
763-753-7374
3
5
Cooler Leg Assembly (Continued)
Cooler Leg Assembly (Continued)
Make sure the cooler legs (Item 2) are flush with the top of the cedar
cooler.
Place the two remaining cooler legs (Item 2) onto the cedar cooler, make
sure the cooler legs are flush with the top of the cedar cooler.
Hold cooler legs tight too the cedar cooler sides and install six #8 x
1-1/2” screws (Item 4) through the cedar cooler walls and into the each
cooler leg at the shown locations.
Hold cooler legs tight too the cedar cooler sides and install six #8 x
1-1/2” screws through the cedar cooler walls and into the each cooler leg
(see step 3 for screw installation).
NOTE: Install screws within 1/2” to 3/4” from cedar cooler wall corners.
NOTE: Install screws within 1/2” to 3/4” from cedar cooler walls.
NOTE. Once the cooler legs are secured, re-install the shock absorber
onto the mount and install clip.
Close the cedar cooler cover.
2
2
Legs (Item 2)
Flush With
Top Of Cedar
Cooler
2
4
4
4
Legs Flush
With Top Of
Cedar Cooler
Install Screws
(Item 4) Within
1/2” to 3/4”
From Cedar
Cooler Wall
Corners
6
Shock Absorber Disconnect
Bottle Opener Installation
Stand the cedar cooler upright onto the coolers legs.
NOTE: The shock absorber can be disconnected from the cedar cooler
cover to aid in ease of screw installation.
Remove the clip from the shock absorber and disconnect the shock
absorber from the mount.
Remove Clip
To Disconnect
Shock
Absorber
With the two screws provided with the bottle opener, install the bottle
opener (Item 3) as shown, approximately 2” down from the cedar cooler
cover.
NOTE: The bottle opener can be installed on the left or right side.
Re-install the plastic cooler into the cedar cooler, make sure the handles
on the plastic cooler are in the down position.
3
www.gronomics.com
East Bethel, MN USA
763-753-7374
Download PDF
Similar pages