WATER HERO P-100 FLOW MONITOR &

WATER HERO P-100
FLOW MONITOR &
SHUT-OFF
DESCRIPTION
Water Hero P-100 provides minute-by-minute water
consumption data to a web interface/ smartphone.
When a leak is detected users receive a text/email
alert and water is shut-off. It works by reading the
rotations of a typical water meter and converts these
rotations to digital flow readings.
Leak alerts are sent and automatic shut-off occurs when there is continuous
flow for more than a user set amount of time. Water Hero also alerts users
when it detects high or low temperatures that could indicate a fire or furnace
failure. Features include:
•
Functions like a security system with two modes (home/away) and user
configurable text/email alert and automatic shut-off
•
Remote water shut-off via smartphone/web interface
•
On board temperature sensor
•
Rechargeable back-up battery for operation in power outage
•
Tracking of historical water consumption
OPERATIONAL REQUIREMENTS
• Broadband Wi-Fi connection [unless opting for cellular option]
• Household power for wall adapter
• Cut into pipe by experienced plumbing contractor
HOW TO PURCHASE OR LEARN MORE
Offered in ¾” and 1” pipe size through a contractor or through the Water Hero
website. Reach out to us at info@waterheroinc.com or +1-617-819-4376 for
pricing information and/or questions
WATER HERO P-100
FLOW MONITOR &
SHUT-OFF
COMPONENTS INCLUDED
The P-100 unit consists of three components and access to our software
system. Not shown here but also included is a wall adapter and RJ45 cord
Main Board with Wi-Fi
chip and state-of-theart processor
Water Hero smart
electronics, brass water
meter and union
couplings
Motorized ball valve
SOFTWARE OVERVIEW
Historical & Measure Flow Functions
Dashboard
Alert Settings
WATER HERO P-100
FLOW MONITOR &
SHUT-OFF
IN-LINE COMPONENT SPECIFICATIONS
VALVE:
• NSF Certified on/off solenoid valve
• Body Material: Stainless Steel 304
• Rated for 70,000 turns
• Manual Override
• Open/close time: ~ 5 seconds
• Max working pressure: 1 MPa
• 3/4” or 1” NPT Size
WATER HERO ELECTRONICS, METER & UNIONS:
• NSF Certified multi-jet water meter
• Magnetic sensor w/ RJ 45 connection
• High/Low Flow Rate: 20/.25 GPM
• Accuracy varies by flow rate
• Max Working Pressure: 150 PSI
• 5/8 x 3/4” meter or 1” meter
• Unions: ¾” or 1” NPT Size
INSTALLATION SUMMARY
Installation typically takes approximately 1 hour and requires the following high level
steps:
• Interconnect unit with existing homeowner WiFi network
• Drain water after the point of installation
• Cut ~12” to 16” section into the pipe where water enters the home
• Assemble and solder any necessary fittings, unions, water meter and actuator valve into
the pipe
WATER HERO P-100
FLOW MONITOR &
SHUT-OFF
TYPICAL CONFIGURATION*
Street side
In-building
Main Water
Supply
Utility
Water
Meter
can be at
street
• Must be installed inside,
unit not waterproof
• Unit Wall Power Adapter
needs access to plug into
household power
Water Hero P-100
• Main Board with WiFi chip
must be located in reach of
2.4 GHz Internet signal
Utility Water
Meter and/or
shut-off valve
can be located
where water
enters building.
Install Water
Hero after City
Meter and
shut-off
Water Hero
Motorized Ball
Valve
Water Hero smart
electronics, water
meter and union
couplings
• Install after Utility Water
Meter, near where main
water supply enters the
building via basement, slab
(can be modified based on
space/power options)
• Horizontal or vertical
installation
• 12” to 16” straight pipe
space required
Fire Suppression
System
IMPORTANT INSTALLATION SAFETY CONSIDERATION*
Water Hero P-100
WARNING: Water Hero P-100 must be
plumbed after (downstream of) fire
suppression systems
*Installation must comply with federal, local and state building and plumbing codes
Download PDF
Similar pages