Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
UPS & BATTERY SYSTEM TECHNICAL
SPECIFICATIONS
FOR
PROPOSED DATA CENTRE
AT
INDIAN INSTITUTE OF TROPICAL
METEOROLOGY, PUNE.
Page 1 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
CONTENTS
A. GENERAL TERMS AND CONDITIONS
B. TECHNICAL SPECIFICATIONS
C. PRICE SCHEDULE
Page 2 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
A. GENERAL TERMS AND CONDITIONS
INSTRUCTIONS TO BIDDERS
1. M/s INDIAN INSTITUTE OF TROPICAL METEOROLOGY. Wishes to receive Bids for Design,
supply ,installation , testing and commissioning of UPS along with Battery , Battery
rack, DC System Cabling etc
as describing in below document. as describing in below
document.
2. In case, any clarification is required, the Bidders shall obtain the same from the IITM in writing. All
such clarifications shall be binding both on the IITM/Consultant and the Bidder.
3. At any time prior to the deadline for submission of Bids, the IITM/Consultant may, for any reason,
whether at its own initiative or in response to a clarification requested by a prospective Bidder,
modify the tender document by amendments.
4. The Bidders shall submit their detailed techno-commercial offer in prescribed format one copy to
IITM in sealed envelope.
5. The details regarding the Bidder’s experience, detailed catalogue of the equipment offered shall be
included in the offer.
6. The prices & rates quoted by the Bidder’s shall be valid & shall be kept open for acceptance for a
minimum period of thirty (30) days from the date of opening of tender.
7. The offers, with the required copies must be received by IITM / Consultant not later than 17.00 hrs
on ------ at following address.
M/s INDIAN INSTITUTE OF TROPICAL
METEOROLOGY, Pune.
Dr. Homi Bhabha Road, Pashan, Pune-411008, INDIA
Contact person: - Shri Jnanesh S.P.
Contact No: Email: -
02025904355
jnanesh@tropmet.res.in
8. The acceptance/rejection of the quotation will rest with the IITM, who does not bind himself to
accept the lowest quotation or any quotation & reserves to himself the full rights for the following
without assigning any reason whatsoever
Page 3 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
PROJECT INFORMATION
1. Project
2. IITM/Owner
Proposed Data Centre At INDIAN INSTITUTE OF TROPICAL
METEOROLOGY, Pune.
M/s INDIAN INSTITUTE OF TROPICAL METEOROLOGY, PUNE.
Dr. Homi Bhabha Road, Pashan, Pune-411008, INDIA
Contact person: - Shri Jnanesh S.P.
Contact No: Email: -
02025904355
jnanesh@tropmet.res.in
3. Nearest Town/City
Pune
4. Nearest Rail Station
Pune
5. Nearest Air Port
Pune
6. Nearest Highway
NH-4
7. Site Conditions
Ambient Temperature:
Maximum: 45 OC
Minimum: 08
O
C
Relative Humidity:
Maximum: 90%
Minimum: 30%
Design Altitude: less than 950m above Mean Sea Level
.
Page 4 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
B TECHNICAL SPECIFICATIONS
1.
ELECTRICAL SYSTEM DETAILS
Design Temp. - 500 C.
HT Supply:
LT Supply Input for UPS : 3 Phases – 415V AC, +/- 10%, 1 Phase – 240VAC, +/- 10%,
50Hz+/- 3%
2.
STANDARDS
In general the Equipment shall be in line with latest edition of relevant IS / BS / IEE / IEC /
JIS.
Some of relevant Indian Standards are listed below:
(i)
IS: 3700
-
Essential ratings and characteristics of semi-conductor devices.
(ii)
IS: 3715
-
Letter symbols for semi-conductor devices.
(iii)
IS: 4411
-
Code of designation of semi-conductor devices.
(iv)
IS: 5001
-
Guide for preparation of drawings for semi-conductor devices.
(v)
IS: 5469
-
Code of practice for the use of semi-conductor junction devices.
(vi)
IEC 62040-3 (International Electrotechnical Commission) – Uninterruptible power
systems (UPS) – Part 3:
Method of specifying the performance and test
requirements.
(vii)
IEEE 587 (ANSI C62.41) Category A & B (International Electrical and Electronics
Engineers) – Recommended practices on surge voltages in low voltage power
circuits.
(viii)
CISPR 22: FCC Rules and Regulations 47, Part 15, Class A (Federal Communications
Commission) – Radio Frequency Devices (prior to Feb 16, 2006).
A.
MIL-HDBK-217E (Military Handbook) – Reliability prediction of electronics
equipment
1. ISO 9001, "Quality Management Systems - Requirements." or
2. ISO 14001, “Environmental Management Systems - Requirements with Guidance
for Use.”
B. UPS should be certified for LEED credits and/or for sustainable/GREEN product
certification
Page 5 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
3.
DESCRIPTION & SYSTEM OPERATION
The UPS shall consist of Rectifier / Charger, Battery, Inverter, Static Transfer Switch,
Maintenance Bypass Switch, Synchronizing Equipment, Protective Device and other
Accessories.
The UPS shall provide continuous electric power within specified tolerance, without
interruption, to the critical loads.
Normally electric energy from normal plant power source shall be supplied to UPS System.
The solid-state rectifier / charger shall convert incoming AC power to DC power. The
rectifier / charger output shall be fed to solid-state inverter. The inverter shall convert the
DC power into AC power, which shall supply the load. Upon failure of AC power, input
power for inverter shall automatically be supplied from the battery with no interruption /
disturbance in inverter output in excess of limits specified herein (in these specifications).
At the same time, UPS shall energize an alarm circuit.
The duration for which Battery shall supply A/C power to O/P shall be minimum 15 minutes.
When A/C power is restored, the input power for the inverter and for recharging the battery
shall automatically be supplied from rectifier / charger output without interruption/
disturbance in inverter output in excess of limits specified herein (in these specifications).
The solid-state circuitry used for both Rectifier & Inverter shall be IGBT technology.
Intelligent RS-232 Communication shall be possible which will Provide UPS status
indications, electrical parameters such as Input & Output Voltage, Load levels etc and
unattended shutdown.
User-friendly LCD Display to indicate all important UPS parameters such as Input Voltage,
Output Voltage, Battery Level and Load Level shall be provided.
The UPS system shall consist of the following modular architecture
4.
ARCHITECTURE
A. Scalable array Infrastructure:
The system power train shall be comprised of 500 kVA power modules and shall be capable
of being configured for N+X redundant operation at the rated i.e. 500KVA system load. This
500kVA systems shall be capable of paralleling with similar rating system to form a bus of
1.5 MW. This 1.5MW system should be load bus synchronous to a similar rating bus. These
2 nos. 1.5 MW bus shall form 2 sources (A & B ) required. The architecture should have the
flexibility of adding this 500KVA power modules without the need of any external cabling of
addition of panels.
B. Module Management:
The modular UPS shall offer the ability to scale its capacity and/or redundancy by
automatically shifting load to fewer power modules. The UPS shall provide an Module
Management System, which will control the UPS to selectively place unnecessary modules in
the “mode” based on the sensed output load level. This is in order to drive the load higher
on the remaining modules. Therefore, with multiple modules, a UPS shall achieve 2-3%
higher efficiencies than conventional operation when loaded less than 50% of system rating.
In case of instantaneous addition of full load on the bus this modules should assume load
without any interruption to the total load.
Page 6 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
C. EcoMode:
In bypass operation, an even higher operating efficiency may be achieved without sacrificing
protection when there are good power conditions. Depending on configuration, efficiency
can exceed 99%.The load remains in bypass mode until the input voltage exceeds tolerance
levels, and then enters full protection mode. This setting is disabled by default and can be
configured using the display. UPS should be capable of operating in ECOMODE even when
they are paralleled to form 1MW bus.
D. Concurrent maintenance:
Any redundant internal module can be concurrently isolated and serviced (by factory-trained
service engineers) while the other internal module/s continues to provide protected power
to the load.
E. Load Test at Site:
UPS should have the ability to perform a full load test in double conversion mode without
the connection of a load bank.
5.
MODES OF OPERATION :
Each module shall operate as an on-line, fully automatic system in the following modes:
A. 3x 500kVA(N+X) :2 Pairs of 3x500kVA(N+X) Working in N+N
The UPS system shall be made up of 3 identical, parallel-connected Integrated Parallel Units
UPS, all having the same power rating. Each Integrated Parallel Unit UPS shall operate in
double-conversion mode and shall be of the VFI-type as per standard IEC 62040-2. The
system shall include 1 redundant Integrated Parallel Units UPS among the total. Such Two
pairs will be working in N+N Mode
B. 2 Nos 100kVA: Working in N+N
The UPS system shall be made up of 2 Standalone UPS, all having the same power rating.
Each Standalone Unit UPS shall operate in double-conversion mode and shall be of the VFItype as per standard IEC 62040-2. The system shall be working in N+N Mode.
Each UPS shall have a rating of 500kVA & 80kVA and shall be made up of the following
components, described in detail in this specification:
● rectifier
● battery charger
● inverter
● battery
● automatic bypass (via a static switch)
● user and communications interface
● Individual battery management system.
● any and all other devices required for safe operation and maintenance, including circuit
breakers, switches, etc.

Battery:
Upon failure of the commercial AC power, the critical load shall continue to be supplied by
the Inverter, which shall obtain power from the batteries without any operator intervention.
Page 7 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
There shall be no interruption to the critical load upon failure or restoration of the
commercial AC source. Each module or system of 500kVA shall have its own Batteries to
meet the autonomy time requirement.

Recharge:
Upon restoration of the AC source, the Charger shall recharge the batteries and
simultaneously the Rectifier shall provide power to the Inverter. This shall be an automatic
function and shall cause no interruption to the critical load.

Bypass:
If the module must be taken out of the standard double conversion mode for overload, load
fault, or internal failures, the static bypass switch shall automatically transfer the critical
load to the commercial AC power. Return from Bypass mode to Normal mode of operation
shall be automatic. No-break transfer to and from Bypass mode shall be capable of being
initiated manually from the front panel.

Input Current Total Harmonic Distortion:
The input current THDI shall be held to less than 5 percent at system load greater than 50
percent while providing conditioned power to the critical load bus, and charging the batteries
under steady-state operating conditions. This shall be true while supporting both a linear or
non-linear load. This shall be accomplished without the requirement for additional or
optional filters, magnetic devices, or other components.

Soft-Start Operation:
As a standard feature, the UPS shall contain soft-start functionality, capable of limiting the
input current from 0 percent to 100 percent of the nominal input over a default 10 second
period, when returning to the AC utility source from battery operation. The change in
current over the change in time shall take place in a linear manner throughout the entire
operation.

Magnetization Inrush Current:
The UPS shall exhibit zero inrush current.
6.
SYSTEM CHARACTIRISTICS:
A. UPS output in standard double conversion mode
1.
400V, 3-phase, 4 wire plus ground. Output wiring configuration is based upon input
wiring
configuration for systems without internal transformers.
2.
Steady-state voltage regulation (in inverter) shall be within +/- 1% average from
nominal output voltage.
3.
Transient voltage response shall be < +/- 5% from nominal voltage for load step from
10% to 100%.
4.
Linear load harmonic distortion capability: Output voltage THD of less than 2% for
100% linear load.
Page 8 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
5.
Non-linear load harmonic distortion capability: Output voltage THD of less than 5%
for 100% non-linear load when tested using the non-linear load described in IEC
62040-3.
6.
Manual output voltage adjustment shall be +/- 3% from nominal.
7.
Line synchronization range shall be +/- 3Hz, adjustable to +/- 0,5Hz.
8.
Frequency regulation shall be +/- 0.1Hz free running.
9.
Frequency slew rate shall be adjustable up to 0.7 Hz/second maximum.
10.
Phase angle control:
a)
Balanced linear load shall be +/- 1 degree from nominal 120 degrees
b)
Unbalanced linear loads shall less than +/- 3 degrees from average phase
voltage for 100% load unbalance.
11.
Phase voltage control:
a)
b)
Balanced linear loads shall be +/- 1% from average phase voltage
Unbalanced linear loads shall be less than +/- 5% for 100% load unbalanced
12.
Overload current capability (with nominal line and fully charged battery): The unit
shall operate with up to 110% of resistive/inductive load for 10 minutes, up to 125%
for 30 seconds, and up to 150% for 10 seconds.
13.
Fault clearing current capability: 1000% RMS for 20ms., 600% for 50 ms. With bypass
intervention. Inverter 200% phase-to-phase for 10 cycles;
14.
Static transfer time: No break, completed in less than 4ms.
15.
Acoustical noise: Noise generated by the UPS under normal operation shall not
exceed 85dbA at one meter from any operator surface, measured at 25 degrees C (77
degrees F) and full load, per ISO7779 standard..
16.
EMC Suppression: The UPS shall meet IEC 62040-2, Category C3.
17.
Electrostatic discharge (ESD): The UPS shall meet EN61000-4-2 level 3.
18.
Efficiency: The UPS efficiency shall be up to 94,5%. If UPS requires input filters for
controlling input THD, manufacturer shall state efficiency of UPS with input filters
connected.
B.
Battery management system:
The UPS shall contain a battery management system which has the following features:
1.
The battery management system shall provide battery time remaining while operating
in normal mode and battery mode. Battery time available information shall be
displayed real-time, even under changing load conditions. Upon commissioning,
battery runtime information shall be available.
2.
The battery management system shall automatically test the battery string(s) to
ensure that the battery is capable of providing greater that 80% of it’s rated capacity.
Testing the batteries shall not jeopardize the operation of the critical load. Upon
detection of the battery string(s) not capable of providing 80%, the UPS system will
alarm that the battery needs attention/replacement. The battery test shall be able to
detect the following:
Page 9 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
Open battery string
Shorted battery string
Battery capacity (runtime) less than 80% of “new” battery capacity
3.
4.
The UPS shall communicate battery test and monitoring data to the UPS
manufacturer’s remote monitoring site. Battery life remaining, capacity, and number
of on-battery events shall be provided in a monthly report.
An optional temperature sensor shall be available to monitor the ambient temperature
internal to the battery cabinet. If the ambient temperature increases, the UPS system
charger shall automatically reduce the charging voltage to a level recommended by the
battery manufacturer. If the ambient temperature is decreased the UPS shall automatically
increase the battery charge voltage to that recommended by the battery manufacturer.UPS
MODULE CABINET
The UPS Module Cabinet shall consist of a rectifier / charger, a three-phase inverter, static
transfer switch, maintenance bypass switch , logic, synchronizing equipment, protective
devices, and accessories as required for proper operation.
7.
RECTIFIER / CHARGER UNIT
a)
The rectifier / charger unit shall be solid state and shall provide direct current to the
inverter unit and for battery charging.
b)
An input AC filter shall be incorporated into the rectifier / charger unit. The filter is
not to be add-on in front of the rectifier / charger. This filter is to reduce the current
harmonics feedback into the input AC line to no more than 10%. The filter is to also
improve the input power factor so that it is no more lagging than 0.95.
c)
The rectifier / charger unit shall provide for input current limiting whereby the
maximum input current shall be limited to 125% of the full input current rating. This
current limit shall be in effect, no matter whether the load is connected to the UPS
module or the static transfer switch. That is, if the static transfer switch is supplying
full rated load, then the rectifier / charger must limit the battery recharging to 25%.
Further more, if the load is connected to the maintenance bypass line, the rectifier /
charger input current must automatically reduce to 25%.
d)
The rectifier / charger unit shall provide features whereby when the AC power is
returned after the UPS has been operating on battery power or has been deenergized, the total initial power requirement at the input terminals will not exceed
20% of rated load, and the power will gradually increase to 100% of full rating over
the 15 second time interval. The unit shall be provided with an internal switch so
that walk-in time can be changed from 2 seconds to 15 seconds.
e)
IGBTs in the rectifier / charger shall be fused with fast acting fuses, so that loss of
any one power semiconductor will not cause cascading failures. All fuses shall be
provided with a blown fuse indicator with an alarm indicator on the control panel.
f)
The rectifier / charger unit shall have an output filter to minimize ripple voltage into
the battery. Under no conditions shall ripple voltage into the battery exceed 2%
RMS. The filter shall be adequate to insure that the DC output of the rectifier/
charger will meet the input requirements of the inverter.
g)
The rectifier unit shall be designed to boost charge the completely discharged
batteries in 10 to 14 hours. The changeover between boost charger mode and float
charge mode shall be affected manually/automatically..
Necessary alarms to
Page 10 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
indicate battery discharged and D.C. over voltage conditions shall be provided.
Selector switch shall be provided for selecting the float charge or boost charge mode.
8.
h)
There shall be DC overvoltage protection so that if the DC voltage rises to the preset limit, the UPS module is to shut down automatically and the load is to be
transferred to the static bypass line uninterrupted.
i)
To prevent battery damage from over-discharging at light load, the rectifier / charger
is to automatically raise the shutdown voltage set point as the load is reduced. The
shutdown set point is to increase linearly from minimum to 1.75 volts per cell as the
discharge time increases from 15 minutes to one hour.
j)
The output voltage of the rectifier / charger unit shall be as follows:
Float mode
:
Variable 115 - 130V DC or 230 - 260V DC
Boost mode
:
Variable 125 - 145V DC or 250 - 290V DC
INVERTER UNIT
a)
Advanced PWM Inverter with Precision Control Circuitry using High Performance IGBT
Power Stage. The output shall be Pure Sine-wave output with less than 3% THD.
Exceptional reliability, superior performance, Quite operation with very high reliability
and efficiency shall be the key characteristics.
b)
The inverter unit shall be a solid state device capable of accepting the output of the
rectifier / charger or the unregulated voltage of the battery and provide regulated
rated AC output within specified limits.
c)
The output frequency of the inverter shall be controlled by an oscillator. The
oscillator shall be temperature compensated and be adjustable +5% of rated
frequency. The oscillator shall hold the inverter output frequency to +0.1% for both
steady state and transient conditions. Drift shall not exceed +0.1% during a 24 hour
period. Total frequency deviation, including short time fluctuations and drift, shall
not exceed +0.1% from the rated frequency.
d)
The inverter output shall stay synchronized with the static bypass line provided the
static bypass line remains within +3 Hz of the nominal frequency. If the line
frequency goes outside these limits, the inverter is to break sync with the line and
run on its internal frequency. When the line frequency returns, within limits, the
inverter output is to automatically re-synchronize with the line. The rate of change of
frequency is not to exceed 0.1 Hz per second. The unit shall be provided with an
internal switch so that the synchronizing frequency range can be changed from +3
Hz to +1 Hz or to +0.5 Hz.
e)
The inverter shall be able to sustain an overload across its output terminals up to
150% load, while supplying any load within its rating, without reducing the output
voltage. Loads greater than 150% shall be transferred to the static bypass line.
f)
The inverter, with the static bypass line disabled, shall current limit at 150% rated
current at reduced voltage for any loading over 150% rate load. The inverter shall be
capable of at least 300% current for short circuit conditions. If the short circuit is
sustained, the inverter shall shut down and disconnect automatically from the critical
load bus.
g)
The inverter unit shall be designed to operate from the rectifier output without use of
battery smoothing effect. With the battery connected to the UPS system, a filter
shall be provided at the input of inverter unit to reduce the A.C. Feedback from the
inverter to the battery to a maximum of 2% of the battery AH capacity.
Page 11 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
h)
The inverter unit shall be designed to operate with 93V to 145V DC or 186V to 290V
DC at the terminals of inverter input filter. The output inverter voltage shall be
stabilised to within +2% of the nominal output voltage with a load variation of 0 100% at 0.6 power factor (lagging).
During step loading of 100%. The system voltage dip shall not exceed 15% and
output voltage shall recover to within + 3% of the nominal output voltage within 10
cycles (200 m sec.)
9.
10.
i)
The inverter voltage regulator is to regulate each phase so that an unbalance loading
will not cause the output voltage to go outside the specified voltage unbalance or
phase displacement.
j)
An output AC filter shall be incorporated in the inverter unit. The filter shall reduce
the inverter output voltage harmonics to 5% RMS total and single harmonics to 3%
RMS for linear loads.
k)
Power semi-conductors in the inverter unit shall be fused with fast acting fuses, so
that loss of any one power semiconductor will not cause cascading failures. All fuses
shall be provided with a blown fuse indicator with an alarm indicator on the control
panel.
STATIC TRANSFER SWITCH
a)
The Static Transfer Switch, using solid state devices, shall be provided to transfer the
load between the UPS module and the static bypass line uninterrupted. Automatic
static load transfers are to be initiated when a system overload is greater than
specified here, a branch load circuit faults or a fault within the UPS module occurs.
b)
For Auto or Manual operation of Static transfer Switch Load should not suffer.
c)
If the static transfer was caused by an overload or branch fault and this condition
was rectified, then the static transfer switch is to automatically re-transfer the load
to the UPS module.
d)
The static transfer switch shall be sized to provide 125% rated load continuously.
The switch shall also have an overload rating of 2000% rated load for two cycles.
e)
Any time the load is on the static bypass line, the control panel shall indicate so. The
audible alarm is to sound only after a ten-second delay. If the transfer was due to a
momentary overload and automatically re-transferred back to the UPS module after
the overload was removed, the alarm and indicator are to automatically reset.
f)
This Static Bypass Operation in any Case should not cause any interruption to the
load.
MAINTENANCE BYPASS SWITCH
a)
A manually operated maintenance bypass switch is to be incorporated into the UPS
module cabinet that will connect the load to the input AC power source bypassing the
rectifier / charger, inverter, and static transfer switch.
b)
All energized terminals shall be shielded to ensure that maintenance personnel do
not inadvertently come in contact with energized parts or terminals. A means to deenergize the static switch shall be provided when the UPS is in the maintenance
bypass mode of operation.
c)
While the load is on the maintenance bypass line, it shall be possible to check out the
operation of the rectifier / charger, inverter, and static transfer switch. It shall also
be possible to check the battery operation.
Page 12 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
11.
BATTERY
A Battery system shall be furnished for the UPS with sufficient capacity to maintain UPS
output at the specified load for a duration of minimum 15 minutes. The type of battery shall
Maintenance-free, Valve-regulated type. A minimum of 10 years warranty for performance
of declared parameters within permissible limits shall be provided.
12.
CONTROLS AND INDICATORS
A.
Microprocessor controlled circuitry: The UPS controls shall have the following design and
operating characteristics:
1.
Fully automatic operation of the UPS shall be provided through the use of
microprocessor controlled Digital Signal Processing. DSP shall eliminate variances
from component tolerance or drift, and provide consistent operational responses.
2.
All operating and protection parameters shall be firmware controlled, thus eliminating
a need for manual adjustments. The logic shall include system test capability to
facilitate maintenance and troubleshooting. Printed circuit board replacement shall be
possible without requiring calibration.
3.
Start-up and transfers shall be automatic functions.
B.
Digital Front Panel Display: The UPS control panel shall be a digital front panel display
that features an 8x40 (8 lines, each with 40 characters) backlit LCD display. The LCD shall
display UPS status, metering, battery status, alarm/event queue, active alarms and UPS
configurations. The front panel display shall show a system mimic diagram with an outlined
power path, current operating mode and event logs.
C.
Control Panel Indicators: The UPS control panel shall provide the following monitoring
functions with indicator LED’s:
NORMAL: This shall indicate that the commercial AC utility or generator source is supplying
power to the rectifier and the inverter is supporting the critical load. A text message shall
indicate if the bypass line is not within tolerance.
BYPASS: This shall indicate that the UPS has transferred the load to the bypass circuit.
BATTERY: This shall indicate that the commercial AC utility or generator source has failed
and the battery is supplying power to the inverter, which is supporting the load. A text
message shall indicate if the battery charge is low or if the battery is installed but
disconnected.
ALARM: This shall indicate that the UPS detects an alarm condition, outlined in detail in the
operator’s manual.
D.
Control Panel Controls: The UPS control panel shall provide the following functions from front panel
push buttons:
EVENTS: Displays the list of Active System Events and a historical log of system events.
Historical logs shall include a detailed time stamped list of the latest 128 events.
METERS: Displays performance meters for the system or critical load. When selected, the
front display shall show individual screens of input parameters, output parameters or bypass
Page 13 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
parameters including; voltage, current and frequency. In addition, the battery display shall
show runtime remaining.
CONTROLS: Displays a System Controls screen. Allows selection of operating mode,
normal, bypass, charger on/off and Power Module on/off.
SETUP: Allows display contrast, date and time information serial communication port
configuration and display of firmware revision numbers.
RETURN: Confirms selection or returns to previous screen.
E.
Interface panel: The UPS shall be equipped with an interface panel, located behind a
protective cover, which provides the following signals and communication features in a Class
2 environment:
Alarm contact: A dry contact for annunciating a summary alarm shall be provided for
customer use. This contact shall be Form “C” capable of supplying both N/O and N/C contacts.
Contact ratings shall be 5A max at a voltage not to exceed 28VDC or 30VAC.
RS232 (EIA / TIA-232) communications interface: Circuitry shall be provided for one
RS232 (EIA / TIA-232) communication port for connection to automated service department
diagnostic tools. This port may be used with simple (“dumb”) terminals to gain remote
access to all unit operation information.
Building alarms: Two inputs shall be provided for monitoring the status of external dry
contacts. Building alarms shall be set up through the UPS configuration mode function on the
RS232 (EIA / TIA-232) port.
External EPO contacts: Shall be provided to connect an external remote emergency power
off switch to shutdown the UPS and de-energize the critical load.
Battery control contacts: Contacts shall be provided to connect the battery shunt trip and
auxiliary signals from a battery breaker or battery disconnect switch.
External bypass indicator connection: A connection point shall be provided to
acknowledge that an external maintenance bypass has been closed around the UPS, placing
the critical load on utility power.
The system shall have options to add four (4) additional building alarms, 384 logged events,
4 additional languages, Mandarin or Russian as a primary language.
13.
CABINET
All the cells making up the Battery shall be installed in a free-standing cabinet, that is, of
the same constructions as the UPS module cabinet. The cabinets shall be of the same
height and depth.
Each cell is to be held in place to prevent movement during seismic motion.
Connectors are to be used so that the battery can be disconnected in no more than 42 volt
sections.
14.
BATTERY DISCONNECT CIRCUIT BREAKER
The UPS Module shall have a Battery Circuit Breaker. This circuit breaker is to be mounted
in the battery cabinet. When open, there shall be no battery voltage present in the UPS
Page 14 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
module cabinet. The UPS module shall be automatically disconnected when the battery
reaches the minimum discharge voltage level or when signalled by other control functions.
15.
MIMIC PANEL
The Mimic Panel is to depict a single line diagram of the UPS. Indicating Lights shall be
integrated with the single line diagram to illustrate the status of the UPS power paths. The
functions whose status are to be displayed shall include, but not be limited to, the following:
a)
Input power available
b)
Output power available
c)
Normal operation
d)
Bypass operation
16.
COMMUNICATIONS
A.
Communications Bay: The UPS shall be equipped with field configurable communications
bays that will accommodate four (4) communication devices.
B.
Remote Monitoring:
1.
Optional WEB/SNMP communication capabilities will be available for all systems.
2.
The UPS shall be able to be monitored remotely via communications devices. UPS
manufacturer shall provide optional communications devices capable of
communicating via various industry standard protocols such as RS232 and ModBus.
Monitoring of UPS status may also be performed through isolated dry contact Form C
relays.
3.
Remote monitoring of the UPS shall also be possible through status indicators
elsewhere in the same facility through a device that replicates these indicators.
The UPS communication capability should be able to integrate into any industry standard
Building Management System (BMS) and/or Network Management System (NMS). The UPS
must also be able to be monitored via any standard Internet browser (i.e. Internet Explorer
and Netscape).
All optional hardware interfaces shall be “Hot-swappable” (UPS maintains power to critical
applications while changing interfaces).
C.
D.
Shutdown:
1.
There shall be a mechanism that provides graceful, orderly, unattended, sequential
shutdown of one or multiple computers powered by one UPS. This shutdown shall be
performed via in-network or out-of-network means. The order of shutdown shall be
user-defined, allowing the maximization of runtime on battery for more critical
systems.
2.
Shutdown of AS/400 computers shall be possible through open-collector relay contacts
or isolated, dry contact, Form-C relays.
3.
The UPS shall also be capable of interfacing with an operating system’s built-in
shutdown routine, e.g. Windows NT. This shall be done through a cable connection to
the optional serial port on the UPS.
Notification:
1.
There shall be a mechanism to send alerts to key personnel via email or SNMP traps.
An alarm notification may also be sent by a network message.
Page 15 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
2.
Dial-out to a computer for alarm notification may be performed. The user may
respond by dialing-in to retrieve alarm history and a summary of current meter status.
3.
Management: A remote battery test may be performed via an Ethernet network. The UPS
shall be tested through invoking a single command.
17.
INSTRUMENT, INDICATIONS AND ANNUNCIATIONS
Following along with described above shall be provided on the system
AA)
Charger Panel
AC Line Voltage (with a selector switch)
AC Line Current (with a selector switch)
Charger Output Voltage (each)
Charger Output Current
Battery Current (charging / discharging current)
BB)
Inverter Panel
DC Input Current
Standby Transformer Secondary Voltage
UPS Output Voltage
UPS Current
Power Factor Meter
Frequency Meter
Following indications lamps shall be provided
AA)
Charger Panel
AC mains ON (3 Lamps)
Battery on Float
Battery on Boost
BB)
Inverter Panel
Battery Output ON
Inverter - I Feeding
Inverter - II Feeding (Only for redundant system)
Standby Supply ON
Load on Bypass
Mains Synchronised
Page 16 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
Audio-Visual Alarm shall be provided for the following complete with ‘ACCEPT’,
‘RESET’ and ‘TEST’ facilities.
AA)
BB)
18.
Charger Panel
a)
Mains Undervoltage / Single Phasing
b)
Charger Failure / SCR Fuse Failure
c)
Reverse Polarity on DC Bus
d)
Cooling Fan Tripped (common for all fans)
e)
Battery Discharged
f)
DC Over-Voltage
g)
Battery Earth Fault
Inverter Panel
a)
DC Input Failure
b)
Inverter - I Output Trouble
CONSTRUCTION
a)
Rectifier / Charger and Inverter sections shall be housed in separate panels and shall
be complete with all interconnections. The panels shall be fabricated with 1.6/2 mm
thick cold rolled sheet steel and structural steel. The panels shall be free-standing.
Verminproof fitted with suitable louvers for ventilation and cooling fan. Hinged doors
shall be provided at the front and back where required, with dust tight gaskets.
Interpanel sheet steel barriers shall be used. The enclosure shall be IP-51 (NEMAIA).
b)
Power cables shall be with aluminium / copper conductor as specified in SLD.
Control cables shall be with copper conductors. All Cable connections shall be from
bottom and from the front of the panel. At the bottom of the panels, a removable
bolted gland plate shall be provided with double compression type cable glands fitted
to it for external cable connections. Clamp type terminals shall be used for
connection of all wires upto 10 mm2 and terminals for larger size shall be bolted type
suitable for cable lugs.
c)
Busbars shall be colour coded and live parts shall be properly shrouded to ensure
complete safety to personnel intending routine inspection by opening the panel
doors. All equipment inside the panel and on door shall have suitable nameplates
and device number as per the schematic diagram.
d)
All fuses shall be link type with HRC links and mounted inside the panel. All power
and control switches shall be mounted on the door operable externally and shall be
rotary type. Space heaters and 100W incandescent lamps shall be provided in each
panel. All instruments shall be switchboard type, back connected, 96 x 96 mm
square of own manufacturers make.
Scale shall have a red mark indicating
maximum permissible operating rating. Test terminals shall be provided on a
separate rail for measuring and testing of equipment to check the performance.
e)
A suitably sized earth bus shall be provided at the bottom of the panels with
provision for earth connection at both ends to IITM's main earth grid. Suitable
Page 17 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
earthing of potential-free metallic parts of various equipment shall be done to ensure
safety.
f)
19.
All metal parts shall be treated so as to ensure efficient anti-corrosive protection.
Hardware shall be zinc passivated or electro galvanised. Panel enclosure and
structure supports shall be thoroughly cleaned and degreased to remove mill scale
and rust, etc.
External surface shall be prepared for final painting with
Manufacturer’s standard colour code.
MECHANICAL DESIGN
A.
Ventilation: The UPS shall be designed for forced-air cooling. Air inlets shall
be on the front of the unit. Air outlets shall be on the top. Eighteen inches of
clearance over the UPS outlets shall be required for proper air circulation. .
B.
No back or side clearance or access shall be required for the system.
The back and side enclosure covers shall be capable of being located directly adjacent
to a wall.
C.
Cable entry: Standard cable entry for the UPS cabinet shall be through either
the enclosure bottom or top. A dedicated wireway shall be provided within the UPS
cabinet for routing user input and output wiring.
D.
Front access: All serviceable subassemblies shall be modular and capable of
being replaced from the front of the UPS (front access only required). Side or rear
access for installation, service, repair or maintenance of the UPS system shall not be
required.
E.
Service area requirements: The system shall require no more than 915 mm
of front service access room and shall not require side or rear access for service or
installation.
Page 18 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
20.
EQUIPMENT DETAILS
All materials and parts comprising the UPS shall be new, of current manufacture, of a high
grade and free from all defects and imperfections and shall not have been in prior service,
except as required during factory testing.
All active electronic devices shall be solid state.
hermetically sealed. All relays shall be dust tight.
All semiconductor devices shall be
The maximum working voltage, current and di/dt of all solid state power components and
electronic devices, shall not exceed 75% of the ratings established by their manufacturer.
The operating temperature of solid state component cases shall not be greater than 75% of
their ratings. Electrolytic capacitors shall be computer grade and be operated at no more
than 90% of their voltage rating.
21.
22.
WIRING
a)
Access holes with cover plates are to be provided on top and bottom of the UPS and
battery cabinets for inter-cabinet wiring and customer installation wiring.
b)
Wiring practices, materials and coding shall be in accordance with the requirements
of the National Electrical Code, OSHA and applicable local codes and standards.
c)
All bolted connections of bus bars, lugs and cables shall be in accordance with
requirements of the National Electric Code and other applicable standards. All
electrical power connections are to be torqued to the required value and marked.
VENTILATION
Adequate ventilation shall be provided to insure that all components are operated within
their environmental ratings. All fans are to be equipped with wind vane sensors connected
to an alarm on the module control panel.
Temperature sensors shall be provided to monitor temperature of critical components.
Upon detection of temperatures in excess of component manufacturer's recommended
ambient working temperature, the sensors shall cause audible and visual alarms to be
sounded on the module control panel.
Forced ventilation if provided by means of fans shall have 100% redundancy.
If redundancy is not provided then it shall be possible to run the system at rated load for
half hour and at reduced load (about 75%) continuously without any damage to the system.
23.
ENVIRONMENTAL REQUIREMENTS
A.
The UPS shall withstand any combination of the following external environmental conditions
without operational degradation.
1.
Operating Temperature: 0 degrees C to + 40 degrees C (32 degrees F to 104
degrees F) no derating is required within this range (excluding batteries).
2.
Storage Temperature: - 25 degrees C to + 60 degrees C (-13 degrees F to 140
degrees F). Prolonged storage above + 40 degrees C (104 degrees F) will cause rapid
battery self-discharge.
3.
Relative Humidity (operating and storage): 95% maximum non-condensing.
4.
Elevation:
Page 19 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
24.
(1)
Operational: 1000 meters above sea level at 40 C maximum. Above this
level altitude de-rating as per EN62040-3.
(2)
Transportation: Capable of air transport, excluding batteries.
UPS PROTECTION
A.
Rectifier/Charger and Bypass protection shall be provided through fusing.
B.
Battery protection shall be provided by thermal-magnetic molded-case circuit breakers
in each battery cabinet (if standard battery pack is provided) or external protective
device for an external battery.
C.
Electronic current limiting circuitry and fuses in the Inverter circuit shall provide output
protection. To comply with agency safety requirements, the UPS shall not rely upon
any disconnect devices outside of the UPS to isolate the battery cabinet from the UPS.
D.
To comply with agency safety requirements, the UPS shall not rely upon any
disconnect devices outside of the UPS to isolate the battery cabinet from the UPS.
Page 20 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
25.
SPARES
Vendor shall recommend and provide spare parts needed for start-up and two years
operation. Recommended spares should take into account related factors like equipment
reliability, effect of equipment downtime upon production and safety, cost of and availability
of equipment service facilities.
All spare parts furnished by vendor shall be wrapped and packed so that they will be
presented in original as new condition under the normal conditions of storage to be
anticipated and shall be properly taped and coded so that later identification as to intended
equipment usage will be facilitated. They shall be packaged separately, clearly marked as
spare parts and shipped at the same time as the equipment. Packing list shall be furnished
so that the parts can be handled without uncrating, if desired.
26.
INSPECTION & TESTING
26.1. The Battery shall be subject to inspection by Client's representative. Manufacturer
shall furnish to inspectors all requested information concerning the supply.
26.2. Battery shall be tested as per relevant IS and test certificates shall be furnished
before despatch.
26.3. The UPS System will be tested in the presence of Client's representative.
following tests shall apply:
The
26.3.1.
Full load heat run for eight hours (unit rate to be furnished separately).
26.3.2.
Current forcing test.
26.3.3.
Recording of time for mains to inverter changeover and vice-versa.
26.3.4.
Recording of 1/2 load change transient.
26.3.5.
Recording of full load change transient.
26.3.6.
Functional Tests.
26.4. Detailed inspection will be performed to ascertain that the data sheet and other
contractual aspect are complied with the earthing system must be inspected for
robustness and continuity.
26.5. QAP plan needs to be submitted before inspection for approval .
27.
SAFETY
27.1. The UPS shall be compliant with IEC 62040-1.
28.
DRAWINGS
28.1. The Manufacturer shall Supply Drawings & documents to the satisfaction of the
client in 6 sets. All drawing to be submitted in Auto CAD format only.
29.
SUBMITTALS
A.
The UPS shall be supplied with sufficient documentation, including the following manuals:
1.
Installation and Operation Manual: One copy of the installation and operation
manual shall be furnished. It shall possess sufficient detail and clarity to enable the
Page 21 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
owner’s technicians or representatives to install and operate the UPS equipment and
accessories. The manual shall include the following major items:
a)
UPS description
b)
UPS site planning and unpacking
c)
UPS installation
d)
Optional accessory installation
e)
UPS theory of operation
f)
Operating procedures
g)
System events
h)
UPS maintenance
i)
Performance and technical specifications
j)
Wiring requirements and recommendations
k)
Physical features and requirements
Cabinet dimensions
30.
DATASHEET- The Manufacturer shall Supply Drawings & documents to the satisfaction of
the client in 6 sets.
31.
INSTALLATION
A.
Install in accordance with manufacturer’s instructions.
32.
COMMISSIONING
A.
UPS manufacturer shall offer the following optional services:
B.
1.
Pre-energize visit to inspect installation and provide guidance to installers as
required.
2.
Post-start-up visit for alarm notification configuration, operator training, etc.
The following procedures and tests shall be performed by Field Service personnel during the
UPS startup:
1.
2.
3.
Visual Inspection:
a)
Visually inspect all equipment for signs of damage or foreign materials.
b)
Observe the type of ventilation, the cleanliness of the room, the use of proper
signs, and any other safety related factors.
Mechanical Inspection:
a)
Check all the power connections for tightness.
b)
Check all the control wiring terminations and plugs for tightness or proper
seating.
Electrical Pre-check:
Page 22 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
4.
a)
Check the DC bus for a possible short circuit.
b)
Check input and Bypass power for proper voltages and phase rotation.
c)
Check all lamp test functions.
Initial UPS Startup:
a)
Verify that all the alarms are in a “go” condition.
b)
Energize the UPS module and verify the proper DC, walkup, and AC phase on.
c)
Check the DC link holding voltage, AC output voltages, and output
waveforms.
d)
Check the final DC link voltage and Inverter AC output. Adjust if required.
e)
Check for the proper synchronization.
f)
Check for the voltage difference between the Inverter output and the Bypass
source.
5.
Operational Training: Before leaving the site, the field service engineer shall
familiarize responsible personnel with the operation of the UPS. The UPS equipment
shall be available for demonstration of the modes of operation.
33.
QUALIFICATIONS
A.
The UPS manufacturer shall have a minimum of forty years experience in the design,
manufacture and testing of solid-state UPS systems.
B.
The UPS manufacturer shall have ISO 9001 certification for engineering/R&D,
manufacturing facilities and service organization.
C.
The UPS manufacturer shall maintain a staffed 7x24x365 call center for technical and
emergency support.
D.
Field Engineering Support: The UPS manufacturer shall directly employ a nationwide field
service department staffed by factory-trained field service engineers dedicated to startup,
maintenance, and repair of UPS equipment. The organization shall consist of local offices
managed from a central location. Field engineers shall be deployed in key population areas
to provide on-site emergency response within 24 hours. A map showing the location of all
field service offices must be submitted with the proposal. Third-party maintenance will not
be accepted.
E.
Spare Parts Support: Parts supplies shall be located in the field to provide 80% of all
emergency needs. The factory shall serve as the central stocking facility where a dedicated
supply of all parts shall be available within 24 hours.
F.
Product Enhancement Program: The UPS manufacturer shall make available feature
upgrade service offerings to all users as they are developed. These upgrades shall be
available as optional field-installable kits.
G.
Maintenance Contracts: A complete range of preventative and corrective maintenance
contracts shall be provided and offered with the proposal. Under these contracts, the
manufacturer shall maintain the user’s equipment to the latest factory revisions.
Page 23 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
Sr.
No
34.
GTP TO BE FILLED BY UPS VENDOR.
Description
Requirement
Vendor to
Specify for
500KVA
1.0
MODEL
please specify
1.1
TECHNOLOGY
1.2
1.3
1.4
2.1
2.2
Inverter
Rectifier
Max. Permissible Non-linear
loads
Max. unbalanced load
PHYSICAL Dimension &
Weight
Construction
UPS Floor Space
IGBT Rectifier & IGBT
Inverter,
Microprocessor
based, true online double
conversion,
Online
Transformer
freeTechnology
IGBT
IGBT
100%
2.2
Ventilation
2.3
UPS Dimension & weight
Length in MM
Width in MM
Height in MM
Weight in kgs
Batterty Bank (Dimention and
weight)
Length in MM
Width in MM
Height in MM
Weight in kgs
Accessibility ( front & back with
clear Dimension to be specfied )
1.5
2.0
2.4
Cable connection Bottom for
Input & Output.
Parallel Configuration upto no of
Module .
DG Set Sizing No of time of
UPS Module.
& Minimum Size of DG set
Required
Vendor to
Specify for
100KVA
100%
Compact. Modular design
Each UPS Floor space
should not exced 1.26 Sq
meter
Specify
Specify
Specify
Specify
Specify
Specify
Specify
Specify
Specify
Specify
Specify
6 nos
Specify
Page 24 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
3
3.1
3.2
3.3
3.4
3.5
3.7
3.8
3.9
4
4.1
4.2
4.3
Minmum Input circuit breaker
required to be specified
INPUT
Voltage
Voltage range
Frequency
Frequency range
Ripple content
Input Power Factor
100%
75%
50%
25%
Current Harmonic on source
100%
75%
50%
25%
Maximum current with out Battery
Charging
OUTPUT
Voltage
Specify
380V -400V- 415V -433V
340 to 460V
50 Hz
+/- 5 Hz
<1% with battery
connected
0.99
0.99
0.99
0.98
<3%
<5%
<5%
<10%
Amps
380/ 400/ 415 V
KW
Voltage regulation
Balanced
+/- 1%, 3 Ph. + N
Un Balanced
+/- 3%, 3 Ph. + N
4.4
Power Factor
0.8lag - unity- 0.9 lead
(Derating of UPS not
acceptable in this range)
4.5
4.6
4.7
4.8
Frequency
Frequency range
Frequency synch. range
Transient output voltage variation
for 100% block loading
Recovery time for 100% block
load
Wave form
Total Voltage Distortion out put
side
Linear load
Non-Linear load
Crest Factor
50Hz
+/- 0.5 Hz
0.25 to 3 Hz
+/-2%
4.9
4.11
4.12
4.13
< 5 mill second (ms)
Sinusoidal
<2%
<3%
3:1
Page 25 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
4.14
Phase Displacement
a) Balanced load
120 +/- 0.65°
120 +/- 2°
4.18
b) 100 % Unbalanced load
Inverter Efficiency
c) 100 %
Overall Efficiency for UPS
b) 50 %
c) 75 %
d) 100 %
Efficiency of UPS in Battery
Operations
b) 50 %
c) 75 %
d) 100 %
Overload
4.19
a) 125 %
b) 150 %
Short circuit Capability
10 minutes
30 Sec
Vendor to Specify
5
5.1
BUILT IN STATIC BYPASS
Inverter and Static Bypass
change over time
Required
Specify
5.2
Fuse @ static bypass
No as per IEEE standards.
5.3
Short circuit Capability
Vendor to Specify
5.4
Overload
Specify
5.5
5.6
Less than 5 milli secs.
Required
6.1
6.1
Transfer time
Manual Bypass inside ups only(
input/output)
DC CHARACTERISTIC
Battery backup to be
calculated at .9 pf.
VAH
DC bus voltage
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
DC Current
No. of cells with AH
battery voltage
End. Cell voltage
Float voltage
DC current at 100% load
Charging current
Charging time
Specify
Specify
Specify
1.75
specify
specify
specify
10 Hrs. max.
4.15
4.16
4.17
6
Specify
91%
91%
92%
>43200
Specify
Page 26 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
6.10
True autonomy / measurement
Software on SNMP & UPS
monitor panel
6.11
6.12
6.13
Required/ Mandatory
Required/ Mandatory
Required/ Mandatory
15 Minutes
7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
8
8.1
8.1
8.2
Temp. compensated charger
Automatic battery load test
Batt. Breaker with protection
Required Battery Back Up
PROTECTION
Overload (O/L)
Short circuit (SC)
Input low voltage
Output over voltage
Battery over charging
Battery over discharging
IP Protection
DC over current Protection
ENVIRONMENTAL
Ambient temperature range
Relative humidity
Max. operating altitude
8.3
9
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.10
9.11
10
10.1
10.2
10.3
10.4
10.5
10.6
10.7
10.8
10.9
10.1
10.11
without derating
Acoustic Noise
AUDIO / VISUAL DISPLAY
Over load
Short circuit
Input low voltage
Input over voltage
Battery over discharging
Battery on load
Battery low
Fuse failure
Fan failure
Inverter failure
DC over voltage
VISUAL DISPLAY
Input/Output voltage
Output current .
Input/ Output frequency
Output power in KVA and KW
Output load power factor
Output load crest factor
battery DC voltage
Charging current
Dis-Charging Current
Autonomy Time
Event logs
11
Required
Required
Required
Required
Required
Required
0 to 40° C
95 % RH
1000 M above MSL
65db (Specify)
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
Required
2500 events mandatory
OTHERS
Page 27 of 28
Client: - Indian Institute Of Tropical Meteorology, Pune
Project: - PROPOSED DATA CENTRE AT PUNE
11.2
11.3
11.4
11.5
11.6
11.7
11.8
Required
Required
Required
Required
Required
Required- Mandatory
required
11.9
Software with LAN connect
Auto paging
SNMP compatibility
Diagnostic system
Single line mimic diagram
Telemonitoring with software
Capablity to parallel 6 similar ups
systems
ventilation
11.10
11.11
11.12
Opertating temperature
Battery management
Power Transfer Mode
0-40deg.C
required
12
13
forced air cooling with
integral fans
auto systems ( during fault
condition)
Colour
Online Thermal Disipation in
Btu/Hr
at 100 %
at 75 %
at 50 %
at 25 %
Page 28 of 28
Sr. No. Function
AI
DI
AO
DO
24 Hrs. Operation with 175 TR Chiller 4 Nos. Air-cooled (2 W+
2SB)
1
2
3
4
5
6
7
8
9
11
12
1
2
3
4
5
6
Chiller On / Off command
Chiller Run Status
Chiller local / remote status
Chiller Trip / Fault status
Chilled water supply header temperature
Chilled water return header temperature
Chilled water return header flow rate
Chiller isolation valves open / close command
Chiller out valves open / close status
Outside air relative humidity monitoring
Outside air temp monitoring
Primary Pump
4
4
4
4
Potential free contact from DDC
Potential free contact from DDC
Potential free contact from DDC
Potential free contact from DDC
1
1
1
Immersion Temperature sensor by BMS Vendor (Daikin)
Immersion Temperature sensor by BMS Vendor (Daikin)
Flow meters by BMS vendor (VKHVAC)
4
4
Potential free contact from DDC
Potential free contact from Valve Actuator
1
1
Outside Air Humidity Sensor to be supplied by BMS vendor
Outside Air Temperature Sensor to be supplied by BMS vendor
Pump Start/Stop Command
4
Potential free contact from DDC
Pump Auto/Manual Status
4
Potential free contact from Pump panel
Pump Run Status
4
Potential free contact from Pump panel
Pump Trip Status
4
Potential free contact from Pump panel
Differential Pressure Snsor
DP sensor in CHW Line by BMS vendor (VKHVAC and DAIKIN)
4
VFD Speed Control
4
0-10V DC control Signal form VFD (VKHVAC)
Condenser Fan Auto/Manual Status
4
Potential free contact from Pump panel
Condenser Fan Run Status
4
Potential free contact from Pump panel
Condenser Fan Trip Status
4
Condenser Coil fan Section
1
2
3
4
5
6
Potential free contact from Pump panel
Condenser Isolation Valve Command
4
Condenser Isolation Valve Open/Close status
Condenser Fan VFD Speed Control
1
2
Valves
Motorized isolation valves for main chiller header
2 way motorized valves
III
Comfort AC for Electrical, UPS and BMS room
2
3
4
5
6
Ductable units ON/OFF Command
Ductable units TRIP STATUS
Room temperature and RH Sensor
Humidity Sensor
Battery room exhaust fan
C
Electrical System
I
Main Power Panel HT, Main LT
4
4
Potential free contact from DDC
Potential free contact from Valve Actuator
4
0-10V DC control Signal form VFD
4
4
4
Potential free contact
4
4
Potential free contact
10
28
10
Volt Free Contact from BMS to AHU Starter Panel.
Volt Free Contact from ACB to BMS
4
6
Temperature + RH Sensor by BMS
Humidity Sensor by BMS
2
1
Air Circuit Breaker On/Off and Status
30
2
Air Circuit Breaker TRIP Status
30
II
UPS Input Panel 1 & UPS Output Panel 2 and non-IT UPS panel : 4 nos
1
Air Circuit Breaker and MCCB On/Off/TRIP Status
30
2
ACB/ MCCB TRIP Status
30
III
Chiller panels, pump, secondary pump panels
1
Air Circuit Breaker On/Off/ Status
30
2
ACB /MCCB TRIP Status
30
III
PAHU , PAHU fan,lightning, emergency lighting panels
1
MCCB On/Off/ and status
10
2
MCCB TRIP Status
DG Breaker 1 ,2 ,3 4 and 5 in synch Panel
10
30
30
Volt Free Contact from ACB to BMS
Volt Free Contact from ACB to BMS
30
Volt Free Contact from ACB to BMS
Volt Free Contact from MCCB to BMS
30
Volt Free Contact from ACB to BMS
Volt Free Contact from MCCB to BMS
10
Volt Free Contact from MCCB to BMS
Volt Free Contact from MCCB to BMS
Through Plant manager
HT breaker 1 ,2 and 3
18
Underground Diesel Storage Tank - Pump 1 W and 1 SB
Level Sensor - HSD
8
4
4
Transformer 1 and 2
12
Miscellaneous
Sensors in BMS vendor scope
1
RH and Temp sensors
2
CO2 Analysers
10
2
7
VFD fans for Battery rooms
3
8
Exhaust fans for Utility room ground floor and first floor (on/0ff/ and trip): 10 fans
9
Hydrozen PPM meter integration
2
Total
44
373
9
Spare @20%
9
75
2
28
53
448
11
169
Total hardware points
CO2 analyszers in BMS vendor scope
3
5
5
sensor in BMS vendor scope
141
Software Points
D
Integration
1
Integration of Chiller Plant Manager to BMS on MODBUS RTU on RS485
2
DG 1 ,2 and 3
3
DG flow meter 1,2,3 and 4
Load Manager
3
Integration of UPS' s on BACNet/IP / MODBUS RTU
8 Static UPS by UPS vendor (160 Points)
4
Integration of PAC' s on BACNet/IP / MODBUS RTU
3 Nos. of PAC's by PAC vendor (45 points)
5
Integration of PDU's on BACNet/IP / MODBUS RTU
8 Nos. of PDU's by PDU vendor (48 points)
6
Integration of EA on MODBUS RTU on RS485
60 EA supplied by Electrical vendor (240 points)
240
8
Integration with addressable Fire alarm system
Software level Seamless integration with BMS (200 points)
9
Access Control system
200
50
105
3Nos. Chiller's supplied by HVAC vendor. (105 Points)
90
60
120
30
160
45
ATS panel 1 and Panel -2
7
10
WATER LEAK DETECTION
Software level Seamless integration with BMS on Same platform.
Unlock the main doors in case of emergency.
MODBUS inetrface with BMS/ Hardwire Interface thru DDC
11
VESDA
MODBUS inetrface with BMS/ Hardwire Interface thru DDC
12
Gas supression system status
hardwired
13
Rodent repellant
MODBUS inetrface with BMS/ Hardwire Interface thru DDC
50
75
2
20
1247
Total Software points
Spare of 20%
249.4
Total software points
Total Hardwaired Points
1496
680
Total Software Points
1496
Total Hardwired and Softwired Points
2177
Note- DG , Transformer , LT breaker , ATS , HT panels are in the sunstation area
. Local PLC panel ( I/O Panel ) needs to be considered , This data to be bundled
and transmit on MOd Bus by TCP /IP / Ethernet to main BMS server by Cat 6 (
Armoured ) located in ground floor BMS room.Approximate cable length will
be 250 meters.
LEGENDS
EARTHING STRIP
LEGENDS
4X14w. SURFACE MOUNTEDLIGHT FIXTURE
LEGENDS
450X75mm. CABLE TRAY
750X75mm. CABLE TRAY
LEGENDS
2X28w. FIXTURE
11800
2140
3983,98
LEGENDS
450X75mm. CABLE TRAY
750X75mm. CABLE TRAY
2500
EARTHING PIT
2500
2500
2RX750X75mm. VERTICAL
CABLE TRAY
FOR 1st FLOOR
2RX750X75mm. VERTICAL
CABLE TRAY
FOR 1st FLOOR
2140
3983,98
BATTERY-2
BATTERY-1
BATTERY-3B
BATTERY-1B
BATTERY-1B
EARTHING SCHEDULE
EQUIPMENT
BATTERY-3A
BATTERY-3A
BATTERY-3A
BATTERY-2A
BATTERY-2A
BATTERY-1A
BATTERY-2A
BATTERY-1A
BATTERY-1A
MAIN LT SWITCHGEAR - 1
BATTERY-2B
PIT No.
UPS-1B
(500kVA)
UPS-2B
(500kVA)
UPS-3B
(500kVA)
UPS-3A
(500kVA)
UPS-2A
(500kVA)
UPS-1A
(500kVA)
VARIABLE PRI.
PUMP PNL- A
STRIP SIZE
600kVAR
CAPACITOR
BANK-2
MECH. SWITCHGEAR - 1
BATTERY-1B
VARIABLE PRI.
PUMP PNL- B
BATTERY-2B
11800
BATTERY-2B
UPS OUTPUT PANEL-B
UPS-1
(100kVA)
MAIN LT SWITCHGEAR - 2
BATTERY-3B
MECH. SWITCHGEAR - 2
BATTERY-3B
UPS-1
(100kVA)
600kVAR
CAPACITOR
BANK-1
EQUIPMENT
PIT No.
STRIP SIZE
UPS-2A
(500kVA)
UPS-2B
(500kVA)
UPS-1A
(500kVA)
UPS-1B
(500kVA)
EMERGENCY
EXIT
(500kVA)
UPS-3B
(500kVA)
UPS-3A
SERVICES
UPS
ROOM
UPS-1 UPS-1
(80kVA)
(80kVA)
BMS
ROOM
UP
SERVICES
J3
J2
J1
J
K
L
M
5
4A
4
3A
3
2A
2
CLIMATE PLAZA SIDE
64
58
76
71
LIFT
81
SDROOM
BATTERY
SD
BFC
FIRE SUPPRESSION
CYLINDERS
BFC
SD
BFC
59
72
67
77
82
H1-C
BMS
ROOM
SD
LOBBY
BFF
UPS ROOM
H1-C
SD
BFC
SD
SD
BFF
BFC
SD
SD
BFF
BFC
SD
SD
BFF
BFC
MOUNTING DETAILS OF DETECTORS
60
68
73
78
83
79
84
UP
ELECTRICAL, UPS & BATTERY ROOM
750 MM SUNK (SUBJECT TO SITE CONDITION) FROM
SD SD
SD SD
GROUND FLOOR FFL. GROUND FLOOR FFL SHOULD BE 102.8
BFF
BFF
BFC
BFC
ELECTRICAL ROOM
61
69
74
ROAD SIDE
NOTES:-
J2
J1
J
SD
BFF
SD
BFC
SD
BFF
SD
BFC
SD
BFF
SD
BFC
K
SD
BFC
SD
BFF
SD SD
BFF
BFC
SD SD
BFF
BFC
MOUNTING DETAILS OF DETECTORS
L
SD
BFF
SD SD
BFF
BFC
SD
BFF
SD
BFC
SD
BFC
M
SYMBOL
DESCRIPTION
HVAC-CHR PANEL-1
HVAC-CHR PANEL-2
HVAC-CHR PANEL-3
HVAC-CHR PANEL-4
C. L. : 210 kW
LOCATION : CHILLER YARD
CABLE ENTRY: TOP / TOP
C. L. : 210 kW
LOCATION : CHILLER YARD
CABLE ENTRY: TOP / TOP
C. L. : 210 kW
LOCATION : CHILLER YARD
CABLE ENTRY: TOP / TOP
C. L. : 210 kW
LOCATION : CHILLER YARD
CABLE ENTRY: TOP / TOP
HVAC-PRIMARY PUMP
PANEL-1
HVAC-PRIMARY PUMP
PANEL-2
HVAC-PRIMARY PUMP
PANEL-3
HVAC-PRIMARY PUMP
PANEL-4
C. L. : 15 kW
LOCATION : CHILLER YARD
CABLE ENTRY: TOP / TOP
C. L. : 15 kW
LOCATION : CHILLER YARD
CABLE ENTRY: TOP / TOP
C. L. : 15 kW
LOCATION : CHILLER YARD
CABLE ENTRY: TOP / TOP
C. L. : 15 kW
LOCATION : CHILLER YARD
CABLE ENTRY: TOP / TOP
HVAC-PANEL-8
C. L. : 15.00 kW
LOCATION : CHILLER YARD
CABLE ENTRY: TOP / TOP
HVAC-PAC PANEL-1
HVAC-PAC PANEL-2
HVAC-PAC PANEL-3
C. L. : 30 kW
LOCATION : GF PANEL RM
CABLE ENTRY: TOP / TOP
C. L. : 30 kW
LOCATION : GF PANEL RM
CABLE ENTRY: TOP / TOP
C. L. : 30 kW
LOCATION : GF PANEL RM
CABLE ENTRY: TOP / TOP
ARCHIVISTA
ENGINEERING
PROJECTS PVT. LTD.
ARCHIVISTA
ENGINEERING
PROJECTS PVT. LTD.
PASSAGE
DATA CENTER
SYMBOL
PAC-25TR
L(2600)XW(900)XH(1970)
ELECTRICAL
ROOM
SECTION JJ'
DESCRIPTION
64
58
76
71
LIFT
81
FIRE SUPPRESSION
CYLINDERS
BATTERY ROOM
59
72
67
BMS
ROOM
77
82
78
83
79
84
UPS ROOM
LOBBY
60
68
73
UP
ELECTRICAL, UPS & BATTERY ROOM
750 MM SUNK (SUBJECT TO SITE CONDITION) FROM
GROUND FLOOR FFL. GROUND FLOOR FFL SHOULD BE 102.8
ELECTRICAL ROOM
61
69
74
J3
J2
J1
J
K
SYMBOL
L
M
5
4A
4
3A
3
2A
2
DESCRIPTION
J3
J2
J1
J
K
CDU3
CDU 4
L
CDU 5
CDU 6
CDU 1
CDU 2
CDU 4
CDU 3
M
5
4A
4
3A
3
2A
2
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
BASIC COST
Duties and Taxes
SECTION - I : LV Panels & Distribution Boards
1.0
Supply ,Installation, testing and commissioning of L.T. panel
boards Compartmental cubicle type, freestanding with
appropriate cable entries, with Cu busbars & manufactured
based on IS 8623, AEPPL specifications and single line
diagrams. Scope shall include unloading, shifting, unpacking,
Section
assembly
from
storage
place
to
desired
Installation.All required protections will be as per SLD.
(Panels will be supplied by Contractor, M.S. steel angle
support fabrication shall be considered separately.)( As
per Main SLD No.ITM_137_PD_ELEC_SLD_001 )
1.1
4000A
Outdoor
Isolation
Panel
Consisting
of
4000A,ACB,Ics=Icu=60kA & 2 nos CT's of 4000/5A,15VA,CL- Set
PS & 5P20 Resp.,Bottom incoming & top Outgoing
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
1.14
1.15
1.16
1.17
1.18
1.19
1.20
ATS
Panel-01
Consisting
of
4000A,ATS
&
Set
4000A,ACB,60kA,LSIG Protections
ATS
Panel-02
Consisting
of
4000A,ATS
&
Set
4000A,ACB,60kA,LSIG Protections
Set
Main LT Panel - 01
Set
Main LT Panel - 02
Set
Utility Panel
Set
Chiller Panel-01
Set
Chiller Panel-02
Set
UPS OUTPUT Panel-A
Set
UPS OUTPUT Panel-B
Power Distribution Board -01A as shown in SLD with 325
Set
KVA 415/415V,K-4 Isolation Transformer with Off
circuit tapps-380/400/415V
Power Distribution Board -02A as shown in SLD with 325
Set
KVA 415/415V,K-4 Isolation Transformer with Off
circuit tapps-380/400/415V
Power Distribution Board -03A as shown in SLD with 325
Set
KVA 415/415V,K-4 Isolation Transformer with Off
circuit tapps-380/400/415V
Power Distribution Board -04A as shown in SLD with 325
Set
KVA 415/415V,K-4 Isolation Transformer with Off
circuit tapps-380/400/415V
Power Distribution Board -01B as shown in SLD with 325
Set
KVA 415/415V,K-4 Isolation Transformer with Off
circuit tapps-380/400/415V
Power Distribution Board -02B as shown in SLD with 325
Set
KVA 415/415V,K-4 Isolation Transformer with Off
circuit tapps-380/400/415V
Power Distribution Board -03B as shown in SLD with 325
Set
KVA 415/415V,K-4 Isolation Transformer with Off
circuit tapps-380/400/415V
Power Distribution Board -04B as shown in SLD with 325
Set
KVA 415/415V,K-4 Isolation Transformer with Off
circuit tapps-380/400/415V
Set
Variable Primary Pump Panel -01
Set
Variable Primary Pump Panel -02
2
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
Page 1 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
1.21
1.22
1.22
1.23
1.24
1.25
1.26
1.27
1.28
1.29
1.30
2.00
2.1
2.2
Set
Set
Set
1.00
1.00
1.00
Set
1.00
Set
1.00
Set
Set
1.00
1.00
Set
4.00
Set
3.00
Supply installation,testing & commissioning of 70A 3P,25kA
Set
Automatic, Transition,Overlaping Neutral with enclosure COS
4.00
Server Area PAC DB-A
Server Area PAC DB-B
Other Area UPS PDB
600 kVAR RTPFC-1 with 7% detuned reactor with Thyristor
Switch
600 kVAR RTPFC-2 with 7% detuned reactor with Thyristor
Switch
CDU Panel-01
GF Cooling Panel-Wall Mounted Group type Construction
Supply installation,testing & commissioning of 630A 3P,35kA
Automatic, Transition,Overlaping Neutral with enclosure ATS
Switch
Supply installation,testing & commissioning of 100A 3P,25kA
Automatic, Transition,Overlaping Neutral with enclosure
Change Over Switch(COS)
Set
SLDB-01 As Per SLD(DG & Trafo area)
Supply,Installation, Testing & Commissioning of Copper,
indoor/ Outdoor Sandwitch type busduct as per location/
specification of busduct. Busduct shall include all horizontal /
vertical lengths, bends, phase cross over chamber if
necessary, flexible Al./Cu. jumper at Panel/ Trafo. end. Scope
shall include unloading, unpacking, section assembly, shifting
from storage place to desired location. (M.S. steel support
fabrication shall be considered separately.)(Actual
lengths shall be measured at site prior to procurement.
)
4000 Amps, 55kA TPN Aluminium, Sandwitch type Busduct
Rmtr
Indoor/Outdoor as per datasheet.
Set
PCC end tinned copper flexible
BASIC COST
Duties and Taxes
1.00
50.00
4.00
Page 2 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
LT BOQ
Description
Sr. No.
Unit
Qnty
Supply
Rate
3.0
3.1
3.2
3.3
3.4
3.5
Supply, Installation, Testing and Commissioning of double
door prefabricated recessed type MCB DB with CRCA sheet
fabrication with powder coated body concealed in wall or on
support structure. Steel support fabrication shall be
considered separately.
Phase Segrigated 8 way TPN DB with 40A, TP MCB as
Incomer & 40A, 30mA,DP, RCBO as subincomer 3 Nos &
24Nos. of 10-20A SP MCB as O/Gs.(LDB 1)
Phase Segrigated 4 way TPN DB with 63A, TP MCB as
Incomer & 63A, 30mA,DP, RCBO as subincomer 3 Nos &
12Nos. of 10-20A SP MCB as O/Gs.(RPDB 1)
12 way VTPN DB with 100A TP MCCB as incomer & 2 Nos. of
63A TP MCB,5 Nos. of 16A TP MCB & 2 Nos of 32A TP MCBs,
& 9 nos. 20A SP MCB as O/Gs. (ACDB)
12 Way SPN DB with 25A,DP,30mA,RCCB as incomer & 10Nos
10A SP MCB as O/Gs.(Main ELDB)
8 Way SPNDB With 40A DP RCBO,30mA as incomer & 6 Nos
of 10A SP MCB as outgoing (SLDB-02)
4.0
Pre-fabricated, IP 42 enclosure with power sockets,
necessary cable glands & spare knockout holes comprising of:-
4.1
1 No. - 20A 1ø 3 pin Industrial socket + 20A SP MCB.
5.0
Supply,Installation,Testing Commissioning of power sockets,
necessary cable glands & spare knockout holes comprising of:-
5.1
5.2
Pug & Sockets 32Amps 3Ph + N + G (IEC 309)
Plug & Socket 16 Amps P + N + G (IEC309)
TOTAL : SECTION - I
Set
2.00
Set
2.00
Set
1.00
Set
1.00
Set
10.00
Set
Set
215.00
35.00
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
11000.00
2200.00
70.00
500.00
130.00
750.00
300.00
300.00
110.00
250.00
1000.00
250.00
600.00
900.00
800.00
8500.00
BASIC COST
Duties and Taxes
SECTION II : L.V. Cables. (XLPE Insulated)
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
1.14
1.15
1.16
Supply, Installation, Testing and Commissioning of 1100V
grade L.T. XLPE/ PVC insulated multistrand Al./ Cu. conductor
cables on provided prefabricated trays/ pipe/ in trenches with
necessary clamps, identification tag. & all other items
required to complete the task. (Note:-Actual cable lengths
shall be measured at site prior to procurement. )
3.5C
3.5C
3.5C
3.5C
4C x
4C x
4C x
4C x
4C x
4C x
4C x
4C x
4C x
3C x
3C x
5C x
x 400 Sq.mm. A2XFY Cable.
x 300 Sq.mm. A2XFY Cable.
x 95 Sq.mm. A2XFY Cable.
x 50 Sq.mm. A2XFY Cable.
25 Sq.mm. A2XFY Cable.
16 Sq.mm. AYFY Cable.
16 Sq.mm. AYFY FRLS Cable.
10 Sq.mm. AYFY FRLS Cable.
6 Sq.mm. YWY FRLS Cable.
6 Sq.mm. AYFY Cable.
4 Sq.mm. YWY Cable.
2.5 Sq.mm. YWY Cable.
2.5 Sq.mm. YWY FRLS Cable.
2.5 Sq.mm. YWY Cable.
2.5 Sqmm YY FRLS Cable
6 Sqmm YY FRLS Cable
Page 3 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
1.17
1.18
1.19
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
3.0
3.1
3.2
3.3
1C x 300sqmm YY FRLS Cable
1C x 70 Sqmm YY FRLS Cable
24C x 2.5 Sqmm YWY Cable
Supply & installation of End termination for cables as above
with Brass, heavy duty, Single compression glands, lugs,
other consumable, crimping, gland hole drilling, ferrulling,
marking, etc.
3.5C x 50 Sq.mm. A2XFY Cable.
4C x 25 Sq.mm. A2XFY Cable.
4C x 16 Sq.mm. AYFY Cable.
4C x 16 Sq.mm. AYFY FRLS Cable.
4C x 10 Sq.mm. AYFY FRLS Cable.
4C x 6 Sq.mm. YWY FRLS Cable.
4C x 6 Sq.mm. AYFY Cable.
4C x 4 Sq.mm. YWY Cable.
4C x 2.5 Sq.mm. YWY Cable.
4C x 2.5 Sq.mm. YWY FRLS Cable.
3C x 2.5 Sq.mm. YY Cable.(PG Gland)
3C x 2.5 Sq.mm. YWY Cable.
5C x 6 Sqmm YY Cable (PG Gland)
1C x 300sqmm YY Cable PG Gland Termination
1C x 70 Sqmm YY Cable PG Gland Termination
24C x 2.5 Sqmm YWY Cable
Supply & installation of End termination for cables as above
with Brass, heavy duty, Double compression glands, lugs,
other consumable, crimping, gland hole drilling, ferrulling,
marking, etc.
3.5C x 400 Sq.mm. A2XFY Cable.
3.5C x 300 Sq.mm. A2XFY Cable.
3.5C x 95 Sq.mm. A2XFY Cable.
TOTAL : SECTION - II
BASIC COST
Duties and Taxes
Rmtr 10000.00
Rmtr 800.00
Rmtr 250.00
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
28.00
4.00
26.00
8.00
18.00
4.00
10.00
4.00
4.00
28.00
50.00
20.00
450.00
376.00
40.00
4.00
Nos.
Nos.
Nos.
148.00
88.00
2.00
Page 4 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
1.0
2.0
2.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
4
5
SECTION III : Earthing
Supply installation of Earthing station as per IS 3043 using
SIP/PIP electrode complete(Eqvt toSGI,JEF,Ashlok T 39)
with watering pipe & suitable GI strip up to chamber, soil
treatment with suitable backfill powder/compound, brick
inspection chamber with 450x450 mm CI cover,
disconnecting link complete including excavation or earth pit,
refilling.
Supply, installation, testing of GI/ Cu. earthing strips & wires
in ground at a depth of 600 mm. or in ready made trenches
or on ready tray with necessary clamps & bimetallic srips as
per specification. (excavation required for this will be ensured
separately.) Refer layout & tender spec for various
applications
75 x 10 mm. GI strip.
50 x 10 mm. Cu strip.
50 x 10 mm. GI strip.
50 x 6 mm. GI strip.
(Main Grid+ Cable Tray)
32 x 6 mm. GI strip.
32 x 6 mm. Cu strip.
25 x 3 mm. Cu. strip
32 x 6 mm. GI strip. Supported on Porcelain insulator/ J bolt
at every 1.5 mtr interval for building L.A.
8 SWG GI Wire.
1C X 10 Sqmm YY FRLS Cable
Nos.
BASIC COST
Duties and Taxes
32.00
Rmtr 400.00
Rmtr 600.00
Rmtr 500.00
Rmtr 500.00
Rmtr 300.00
Rmtr 250.00
Rmtr 2500.00
Rmtr
200.00
Rmtr
Rmtr
500.00
250.00
Supply, installation, testing & commissioning of Transducer
type Building lightning arrester "EARLY STREAMER" to cover
protection radius of 65.0 mtr. With 3 mtr rod height & with Nos.
stem and fixing arrangement. (Indelec). Required installation/
mounting details shall be submitted prior to installation.
Supply, installation, testing of disconnecting link box for
lightning down conductor at 1 mtr. from GL with SMC Nos.
insulator and Gunmetal 50 x 6 mm disconnecting link.
TOTAL : SECTION III
1.00
2.00
Page 5 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
1
2
3
4
5
5.1
5.2
SECTION IV : UPS
Supply, Installation, testing and commissioning of 500 kVA
UPS , consisting of following
Input 433V 3 Ph + N + E +/-10% 50Hz
Output 400V 3 Ph + N + E , -2% 50Hz
Unsymmetrical load with SMF battery backup for 15 min.
Racks & Intercell connectors suitable for batteries
UPS to battery DC cable to be consider
Installation & commissioning of Batteries & UPS (Lenghths as
per actuals)
Supply, Installation, testing and commissioning of 100 kVA
UPS consisting of following
Input 433V 3 Ph + N + E +/-10% 50Hz
Output 400V 3 Ph + N + E , -2% 50Hz
Unsymmetrical load with SMF battery backup for 15 min.
Racks & Intercell connectors suitable for batteries
UPS to battery DC cable to be consider
Installation & commissioning of Batteries & UPS (Lenghths as
per actuals)
As above but 2 x 2.5 + 1 x 1.5 Sq.mm. wires. In provided
floor Truff / PVC conduit
Providing & fixing 2 Nos. modular 5 A socket & switch (on
UPS) and 1 no 5A & socket & switch (on Raw Power) with
modular plate and box at one place for UPS & mains
connections above table top.
Supply & Installation of MS boxes in flooring made from 16
SWG M.S. sheet with Stainless steel cover of 14 SWG of
following sizes
Supply and installation of Surface / concealed 25mm dia PVC
Conduit with spacer saddles for computer and telephone /
speaker wiring concealed in office area walls & open other
places with pull boxes etc.
Supply and installation of Surface / concealed 25mm dia GI
Conduit with spacer saddles for transformer area wiring
walls & open other places with pull boxes etc.
TOTAL SECTION - IV
Set
6
Set
2
Rmtr
500.00
Set
10.00
Rmtr
200.00
Rmtr
100.00
BASIC COST
Duties and Taxes
Page 6 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
LT BOQ
Description
Sr. No.
Unit
Qnty
Supply
Rate
BASIC COST
Duties and Taxes
SECTION V : Point Wiring
1.0
1.1
1.2
2.0
3.0
3.1
3.2
3.3
4.0
4.1
5.00
6.00
6.1
6.2
Surface / concealed point wiring for light / fan call bell / 5 A
points with 2 x 2.5 + 1 x 1.5 Sq.mm. multistrand Cu. wires
1100 V gr. in suitable 25mm PVC conduits / flexible conduits
wherever required as submains and 2 x 1.5 + 1 x 1.5 Sq.mm.
FRLS wires for each point complete (submains will not be
measured separately) with necessary modular switch board,
switch plates and Blanking plates & accessories as required
etc. to complete the task.. Primary Point shall mean first
point wired from switchboard and Secondary point shall mean
successive points next to Primary point. (Areas : Office,
canteen, Security cabin, Toilets,Production Shop)
Note:- All conduits in area with false ceiling shall be
concealed in wall below false ceiling,point wiring height
will be 3-4 mtr from FFL
Primary Light point wiring with necessary 5 A SP Switch ,
ceiling rose / Holders compete. (Maximum 2/3 points
controlled by one Switch) as reqiured to complete the job.
As above but Secondary Light point wiring.
Fan point with modular 5 A SP Switch, 5 step Electronic fan
Regulator, switch box plate & fan hook box etc. modular, fan
box.
Supply, installation, testing and commissioning of lighting
fixtures/ fans/Ex. fans etc. including necessary electronic
ballast, lamp, accessories, wiring connection, support
arrangement like suspension chain, M.S. conduit drop with
ball socket. down drops, etc. All FTL fixtures shall be with
triphosphor source.
2 X 28 Watt TL-5 Weather Proof Luminaire suitable for TL-D
and TL5 Lamps. high grade Polycarbonate housing and
cover.TCW450 2xTL5-28W EBT
4 x 14 Watt high efficiency Surface mounted luminaire
suitable for T5 lamp with dimmable balast. (Make:- Philips
Cat no.- TPS814 4xTL'5'14W/EBP D8 (4xTL'5'14W) or
equivalent.)
1x 28 watt Saviour Slim Channel luminaire (Wipro WRF 20128
SGW)
Supply, installation testing of Ceiling/Exhaust fans with
necessary acessories to complete the job.
Supply, installation testing of 150mm exhaust fans with
mounting frame & louvers.
Supply, Installation of Junction Boxes made out of CRCA
Sheet (16SWG) with 4way Terminal Strip and appropriate
knock out for loop in loop out of cables. (For Lighting)
Pt.
40.00
Pt.
50.00
Pt.
20.00
Nos.
50.00
Nos.
60.00
Nos
10.00
Nos.
5.00
Nos.
150.00
No
No
10.00
5.00
Supply,Installation,Testing & Commissioning of Exit Signages
Exit
Emergency Exit
Page 7 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
7.0
7.1
8.0
8.1
BASIC COST
Duties and Taxes
Supply, Installation, testing & comissioning of G.I Street Light
Pole having with bottom flange & foundation bolts poles
complete with 1600 x 450 x 450 mm foundation with 2 Nos.
40 mm dia pipes bent to shape 1.5 m. long cable loop box
with 15A 4 way connector, 15A SP MCB, earthing of pole with
8 SWG wire, painting with 2 coats of primer bottom with
blank paint & balance with silver paint.
9 Mtr.Tubular Poles with double bracket for mounting Flood
Light on the same pole.(9 mtr effective height from Ground
level)
Supply, Installation, testing & commissioning of street / flood light
fixture on above poles with necessary hardware etc. including cable
connection box & lamps.
Compact IP65 integral floodlight with symmetric beam
distribution Wipro WFT 52150or Equivalent
TOTAL SECTION - V
No
6.00
No
12.00
Page 8 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
1.0
1.1
1.2
2.0
3.0
3.1
4.0
4.1
4.2
TOTAL : SECTION VI: Data & Telephone Provisions
Supply, installation, testing & commissioning of jelly filled
armoured twisted pair 0.51 mm Cu. telephone cable with PVC
insulation in ready trenches / trays / pipes etc.
20 Pair.
2 Pair Unarm. cable
Supply and laying of CAT 6 cable for Data points in existing
raceways.
Supply and installation of 2 mm thickness Aluminium
extruded raceway for under floor installation including
necessary cutting of floor providing couplers and clamps for
raceway fixing as details provided making good the surface of
floor complete as per sizes provided.
82mm X 38mm deep Al raceways.
Supply, installation of following set of modular sockets with
box, switch plates for telephone & data cables etc. as
required as detailed below.
1 No. RJ 45 data socket with modular box & cover plate.
1 No. RJ 11 telephone socket with modular box & cover plate.
Rmt
Rmt
Rmt
100.00
500.00
Rmt
100.00
No.
Nos.
10.00
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
50.00
60.00
100.00
400.00
200.00
Rmtr
Rmtr
Rmtr
60.00
30.00
50.00
Ton
5.00
BASIC COST
Duties and Taxes
500.00
10.00
TOTAL : SECTION VI
SECTION VII - CABLE TRAYS & FABRICATIONS
1.0
1.1
1.2
1.3
1.4
1.5
2
2.1
2.2
2.3
3.0
Supply and installation of prefabricated (hot dip Galvanised )
G.I. ladder/ perforated trays with 50/ 75 mm C channels &
Runges at 200mm cc and including prefabricated accessories
like Bends, Tee, Right-angles & tray coupling arrangement
etc.(Bends fabricated at site will not be allowed.)
100mm, 50x50 perforated tray. (16 SWG)
150mm, 50x50 perforated tray. (16 SWG)
300 mm, 50x50 perforated tray. (14 SWG)
450 mm, 75x75 Ladder tray. (14 SWG)
750 mm, 75x75 Ladder tray. (14 SWG)
Cable Tray Covers suitable for following size trays
100mm perforated tray.
150mm perforated tray.
300 mm perforated tray.
Supply, Fabrication, Installation of M.S. angle/ Channel/
Square tube of 3mm thick of 50x50mm size including base
plates supports arrangement, fastners, hardware etc. as per
requirement (Duly approved by AEPPL and Client) for trays,
frames etc. including necessary painting with 2 coats of
primer and 2 coats of enamel black paint.
TOTAL : SECTION VII
Page 9 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
LT BOQ
Description
Sr. No.
Unit
Qnty
Supply
Rate
1
1.1
1.2
1.3
1.4
2
2.1
2.2
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
SECTION VIII - ITEMS MAY BE EXECUTED
Distribution Boards & Industral Socket
Supply, Installation, Testing and Commissioning of double
door prefabricated recessed type MCB DB with CRCA sheet
fabrication with powder coated body concealed in wall or on
support structure. Steel support fabrication shall be
considered separately.
8 way TPN DB with 25A 4P 30mA RCBO as incomer & 18Nos.
of 10-20A SP MCB as O/Gs.
8 way VTPN DB with 63A TP MCCB as incomer & 4 Nos. of
10A TP MCB,2 Nos. of 25A TP MCB & 2 Nos of 16A TP MCBs
as O/Gs.
8 way VTPN DB with 63A TP MCCB as incomer & 6 Nos. of
10A TP MCB,2 Nos of 16A TP MCBs as O/Gs.
4 way TPN DB with 63A, TPN RCBO 30 mA as incomer &
12Nos. of 20A SP MCB as O/Gs.
Set
1.00
Set
1.00
Set
1.00
Set
1.00
Set
Set
1.00
1.00
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
BASIC COST
Duties and Taxes
Pre-fabricated, IP 42 enclosure with power sockets,
necessary cable glands & spare knockout holes comprising of:1 Nos. - 63A 3ø 5 pin Industrial socket + 63A TP MCB.
1 Nos. - 32A 3ø 5 pin Industrial socket + 32A TP MCB.
LT Cables & Termination
Supply, Installation, Testing and Commissioning of 1100V
grade L.T. XLPE/ PVC insulated multistrand Al./ Cu. conductor
cables on provided prefabricated trays/ pipe/ in trenches with
necessary clamps, identification tag. & all other items
required to complete the task. (Note:-Actual cable lengths
shall be measured at site prior to procurement. )
3.5C
3.5C
3.5C
3.5C
3.5C
3.5C
4C x
4C x
4C x
3C x
3C x
1C x
6C x
8C x
x 240 Sq.mm. A2XFY Cable.
x 185 Sq.mm. A2XFY Cable.
x 150 Sq.mm. A2XFY Cable.
x 120 Sq.mm. A2XFY Cable.
x 70 Sq.mm. A2XFY Cable.
x 35 Sq.mm. A2XFY Cable.
10 Sq.mm. YWY Cable.
6 Sq.mm. YWY Cable.
1.5sqmm YWY Cable
6 Sq.mm. YWY Cable.
4 Sq.mm. YWY Cable.
6sqmm YY Cable including Termination
2.5 Sqmm YWY Cable
2.5 Sqmm YWY Cable
Page 10 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
5
5.1
5.2
5.3
5.4
6.0
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
6.15
6.16
6.17
6.18
6.19
6.20
6.21
6.22
Supply & installation of End termination for cables as above
with Brass, heavy duty, Single compression glands, lugs,
other consumable, crimping, gland hole drilling, ferrulling,
marking, etc.
3.5C x 70 Sq.mm. A2XFY Cable.
3.5C x 35 Sq.mm. A2XFY Cable.
4C x 10 Sq.mm. YWY Cable.
4C x 6 Sq.mm. YWY Cable.
4C x 1.5 Sqmm. YWY Cable.
3C x 6 Sq.mm. YWY Cable.
3C x 4 Sq.mm. YWY Cable.
1C x 6sqmm YY Cable PG Gland Termination
6C x 2.5 Sqmm YWY Cable
8C x 2.5 Sqmm YWY Cable
Supply & installation of End termination for cables as above
with Brass, heavy duty, Double compression glands, lugs,
other consumable, crimping, gland hole drilling, ferrulling,
marking, etc.
3.5C x 240 Sq.mm. A2XFY Cable.
3.5C x 185 Sq.mm. A2XFY Cable.
3.5C x 150 Sq.mm. A2XFY Cable.
3.5C x 120 Sq.mm. A2XFY Cable.
Spare ACB's and MCCB's
Supply and Installation of Spare Switchgear for modification
and alteration work in LT Panels.
4000A, 4P, EDO, 55kA, LSIG mp based release ACB.
4000A, TPN, EDO, 55kA, LSIG mp based release ACB.
3200A, 4P, EDO, 55kA, LSIG mp based release ACB.
3200A, TPN, EDO, 55kA, LSIG mp based release ACB.
2500A, 4P, EDO, 55kA, LSIG mp based release ACB.
2500A, TPN, EDO, 55kA, LSIG mp based release ACB.
2000A, 4P, EDO, 55kA, LSIG mp based release ACB.
2000A, TPN, EDO, 55kA, LSIG mp based release ACB.
1600A, 4P, EDO, 55kA, LSIG mp based release ACB.
1600A, TPN, EDO, 55kA, LSIG mp based release ACB.
1250A, 4P, EDO, 55kA, LSIG mp based release ACB.
1250A, TPN, EDO, 55kA, LSIG mp based release ACB.
1000A, 4P, EDO, 55kA, LSIG mp based release ACB.
1000A, TPN, EDO, 55kA, LSIG mp based release ACB.
630A,TPN. 55kA,Thermal Release, MCCB
400A TPN. 55kA,Thermal Release, MCCB
315A TPN. 55kA,Thermal Release, MCCB
250A TPN. 55kA,Thermal Release, MCCB
200A TPN. 55kA,Thermal Release, MCCB
160ATPN. 55kA,Thermal Release, MCCB
125ATPN. 55kA,Thermal Release, MCCB
100A TPN. 55kA,Thermal Release, MCCB
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
Nos.
Nos.
Nos.
Nos.
1.00
1.00
1.00
1.00
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
BASIC COST
Duties and Taxes
Page 11 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
7.0
7.1
7.2
8
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
9
Earthing System & L.A.
Earthing station as per IS 3043 - 1987, using Pipe / plate
electrode complete with watering pipe & suitable GI strip up
to chamber, soil treatment with charcoal and salt / bentonite
powder, brick inspection chamber with 450x450 mm CI
cover, disconnecting link etc. And all other work required to
complete the task.
Earthing station as per IS 3043 - 1987 as above using 600 x
600 x 3 mm. Cu. Plate as electrode and other items required Nos.
to complete the task.
As per IS 3043 - 1987 as above but bore type earthing with
3mtr. long 40 mm. dia. GI pipe as earth electrode treatment
with bentonite / earth powder complete including required
Boring, earth strip connection to GI pipe electrode shall be Nos.
with 2nos. GI half round clamps duly welded and bolted at 2
distinct points treatment with bentonite / earth powder
complete including required dia Boring.
Supply, installation, testing of GI/ Cu. earthing strips & wires
in ground at a depth of 600 mm. or in ready made trenches
or on ready tray with necessary clamps & bimetallic srips as
per specification. (excavation required for this will be ensured
separately.) Refer layout & tender spec for various
applications
75 x 10 mm. Cu strip.
75 x 6 mm. GI strip.
50 x 6 mm. Cu strip.
32 x 6 mm. Cu strip.
25 x 6 mm. GI strip.
25 x 3 mm. GI. strip.
25 x 3 mm. GI strip. Supported on Porcelain insulator/ J bolt
at every 1.5 mtr interval for building L.A.
4 SWG GI Wire.
12 SWG GI Wire.
10 SWG GI Wire.
Supply, installation, testing & commissioning of Transducer
type Building lightning arrester "EARLY STREAMER" Protection
level III to cover protection radius of 75.0 mtr. With 5 mtr
rod height & with stem and fixing arrangement. (Indelec or
Eqvt.). Required installation/ mounting details shall be
submitted prior to installation
BASIC COST
Duties and Taxes
1.00
1.00
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
Rmtr
1.00
1.00
1.00
1.00
1.00
1.00
Rmtr
1.00
Rmtr
Rmtr
Rmtr
1.00
1.00
1.00
Nos.
1.00
Page 12 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
10
11
12
12.1
12.2
12.3
13
13.1
13.2
14
14.1
14.2
14.3
14.4
15.0
15.1
15.2
16.0
16.1
Supply, installation, testing & commissioning of Transducer
type Building lightning arrester "EARLY STREAMER" Protection
Level III to cover protection radius of 95 mtr. With 5 mtr rod Nos.
height & with stem and fixing arrangement. (Indelec).
Required installation/ mounting details shall be submitted
prior to installation.
Supply, installation, testing & commissioning of 5 Spikes
Copper Building lightening arrester to be installed on top Nos.
most point of building with stem and fixing arrangement etc.
complete.
BASIC COST
Duties and Taxes
1.00
1.00
Point Wiring & Light Fixtures
Mains Circuit as required
2 x 4.0 + 1 x 2.5 Sqmm FRLS Cu wires as above but in
provided AL floor Truff / in PVC conduit.
Supply and installation of main for UPS power points in plant
area with 2 x 4 + 1 x 2.5 Sq.mm. wires including 25mm PVC
Conduits.
As above but 2 x 2.5 + 1 x 1.5 Cu wires in 25mm PVC
conduit.
Supply & Installation of MS boxes in flooring made from 16
SWG M.S. sheet with Stainless steel cover of 14 SWG of
following sizes
300 x 300 x 50 mm. Floor boxes.
150 x 150 x 50 mm. Floor boxes.
Supply, installation, testing and commissioning of lighting
fixtures/ fans/Ex. fans etc. including necessary electronic
ballast, lamp, accessories, wiring connection, support
arrangement like suspension chain, M.S. conduit drop with
ball socket. down drops, etc. All FTL fixtures shall be with
triphosphor source.
1x 28 watt Decorative luminaire (Wipro WRF 81128 SG)
1x 18 watt Decorative luminaire (Wipro WRF 21118)
4 x 14 Watt STELLAR - Recess mounted special geometric
MO luminaire(Wipro WVF 20414)
2 x 18 Watt Low Depth Recessed downlighter(Wipro
28218)
Supply, installation testing of Ceiling/Exhaust fans
necessary acessories to complete the job.
Supply, installation testing of 1200mm Ceiling fans
300mm down rod canopies but without regulator.
Supply, installation testing of 1400mm Ceiling fans
300mm down rod canopies but without regulator.
Supply, installation testing of wall mounted fans
mounting frame & louvers.
Supply, installation testing of 305mm exhaust fans
mounting frame & louvers.
WCP
Rmtr
1.00
Rmtr
1.00
Rmtr
1.00
Nos.
Nos.
1.00
1.00
Nos
Nos
1.00
1.00
Nos.
1.00
Nos
1.00
Nos.
1.00
Nos.
1.00
Nos.
1.00
Nos.
1.00
with
with
with
with
with
Page 13 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
LT BOQ
Description
Unit
Qnty
Supply
Rate
17
17.1
17.2
17.3
17.4
BASIC COST
Duties and Taxes
Supply,Installation,Testing & Commissioning of Exit Signages
Emergency Exit Door
Emergency Exit Right from here
Emergency Exit Left from here
Staire case up or down
Data & Telephone
Supply & installation of Krone type telephone junction box
18.00
fabricated and painted as per panel specifications.
18.1 50 Pair Box.
18.2 20 Pair Box.
18.3 10 Pair Box.
Supply, installation, testing & commissioning of jelly filled
19.0 armoured twisted pair 0.51 mm Cu. telephone cable with PVC
insulation in ready trenches / trays / pipes etc.
19.1 50 Pair.
19.2 10 Pair Unarm. cable.
Supply & laying of CAT 5E cable for Data points in existing
20.0
raceways or in pre laid FRPVC blank conduits.
Raceway & J.B.
Supply and installation of 2 mm thickness Aluminium
extruded raceway for under floor installation including
necessary cutting of floor providing couplers and clamps for
raceway fixing as details provided making good the surface of
21
floor complete as per sizes provided.
21.1 100mm X 45mm deep Al. raceways.
21.2 125mm X 25mm deep Al. raceways.
Supply and installation of good quality floor junction boxes of
appropriate sizes for raceways with folded frames including
22.0 counter sunk screw arrangements such that covers are in
level with the floor level. The cover will be M.S, power coated
& have 4 Nos. 25 / 32 mm Ø holes with rubber grommets at
appropriate location.
100mm X 100mm X 50mm deep 16SWG junction box with 14
22.1
SWG cover.
125mm X 125mm X 50mm deep 16SWG junction box with 14
22.2
SWG cover.
225mm X 225mm X 50mm deep 16SWG junction box with 14
22.3
SWG cover.
330mm X 330mm X 50mm deep 16SWG junction box with 14
22.4
SWG cover.
450mm X 450mm X 50mm deep 16SWG junction box with 14
22.5
SWG cover.
Supply, installation of following set of modular sockets with
23.0 box, switch plates for telephone & data cables etc. as
required as detailed below.
2 Nos. RJ 45 socket for data with box & cover plate at one
23.1
place.
3 Nos. RJ 45 for 1 telephone and 2 data socket with boxes &
23.2
cover plates at one place.
No
No
No
No
1.00
1.00
1.00
1.00
No.
No.
No.
1.00
1.00
1.00
Rmt
Rmt
Rmt
1.00
1.00
Rmt.
Rmt.
1.00
1.00
No.
No.
No.
No.
No.
No.
No.
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
Page 14 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
LT BOQ
Description
Sr. No.
Unit
Qnty
Supply
Rate
BASIC COST
Duties and Taxes
Cable Tray with Covers & Fabrication
24
24.1
24.2
24.3
25
25.1
25.2
25.3
26.0
Supply and installation of prefabricated (hot dip Galvanised )
G.I. ladder/ perforated trays with 50/ 75 mm C channels &
Runges at 200mm cc and including prefabricated accessories
like Bends, Tee, Right-angles & tray coupling arrangement
etc.(Bends fabricated at site will not be allowed.)
50mm, 50x50 perforated tray. (16 SWG)
200mm, 50x50 perforated tray. (16 SWG)
600 mm, 75x75 Ladder tray. (14 SWG)
Cable Tray Covers suitable for following size trays
50mm perforated tray.
200mm, perforated tray.
450 mm perforated tray.
Rmtr
Rmtr
Rmtr
1.00
1.00
1.00
Rmtr
Rmtr
Rmtr
1.00
1.00
1.00
Supply, Fabrication, Installation of M.S. square tube of 3mm
thick of 40 x 40mm size. including painting with 2 coats of
Rmtr
primer & 2 coats of final enamel black paint as specified. And
all other items required to complete the task.
1.00
TOTAL : SECTION VIII
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot note
Page 15 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
HT BOQ
Description
Unit
Qnty
Supply
Rate
1
2
2.1
2.2
2.3
3
3.1
BASIC COST Duties and Taxes
SECTION-I:-HT SYSTEM
Supply,Erection, Testing and Commissioning of 22
kV / 0.433 kV, 2500 kVA, Dyn 11, 6.25%
Impedance, Oil Insulated Transformer with
OLTC and all accessories complete on
readymade plinth, Scope shall includes unloading
Set
2.00
shifting from stores to plinth and BDV test &
topping up of fresh transformer oil as per
requirement to complete the task.If required
filteration of oil .
Supply,Erection, Testing & Commissioning of Ring
Main Unit(RMU) & HT Switchgear equipment
including necessary support structure, hardware &
testing of the equipment at site after Erection as
per specification. All other work to complete the
erection of equipment.
Supplu,Installation,Testing & Commissioning of 22
kV, 630A, 26kA, Indoor Compact RMU type
(Extendable) including relay and control panel
Set
1.00
.Consisting of 1 I/C SF6 , 3 O/G SF6,and Metering
module Feeders as per SLD.(HT Panel 1).
Supply,Installation,Testing & Commissioning of 22
kV, 630A, 26kA VCB HT PANEL 22kV,630A,26kA
as incomer & 2nos. 22kV, 630A, 26kA Vacuum
Set
1.00
Circuit Breaker as outgoing Panel Extensible type
including Power Pack as per specifications , Data
sheet and SLD.
Removing Existing RMU 1 incoming & One out going
including cable termination,handover to Client as
job
1.00
desired location guide by Client
Supply,Testing, tagging, laying, & commissioning of
following 22 kV grade XLPE HT cable on
readymade Trench/Excavation with (sand
cushioning of 75mm, laying bricks on both sides of
cable) & covering with RCC / PCC tiles or half round
hume pipe of 200 mm dia. and refilling of cable
trench, leveling of cable trench etc. as required.
(Note: Quantity is tentative as Route is tentitively
desided). (Only Hard rock excavation shall be
measured separately).
3C x 240sqmm Al.XLPE HT Cable
Rmtr 700.00
Page 16 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
HT BOQ
Description
Unit
Qnty
8.1
8.2
Supply, installation, testing & commissioning of heat
shrink jointing for 22kV HT cables of following
sizes including necessary accessories, spider
supports, plated hardware like lugs / ferrules,
insulation tapes etc. complete. Standard make.
Scope also includes making suitable cutouts in
gland plate & sealing them after connections.
Indoor End Termination.
Outdoor End Termination.
Providing Chainlink Fencing with 10SWG, 1.5"
Chainlink jali with 50 x 50 x 6 mm M.S. Angle
supports at proper intervals (@2.0m C/C). Fencing
height should be 2.4M above Ground Level. The
rate shall be inclusive of 2No. 3M wide, double leaf
gate made out of 40mm dia., 2mm thk. MS pipe
with proper channel supports and 1Nos. of 1.0M
wide single leaf gate same as above gate etc.
complete including painting with 2 coats of red
oxide primer & 2 coats of silver paint. The rate shall
be inclusive of the required civil work.
( Total perimeter of fencing -- 100M ).
Supply installation of Earthing station as per IS
3043 using SIP/PIP electrode complete(Eqvt to
Ashlok T 39) with watering pipe & suitable GI strip
up to chamber, soil treatment with suitable backfill
powder, brick inspection chamber with 450x450
mm CI cover, disconnecting link complete including
excavation or earth pit, refilling.
Statutary Approval from local EB
Supply, installation, material equipment required as
per statutory provision & safety.
22 kV grade Rubber matting 1000 mm width.
22 kV class Hand gloves.
Mtr
Pair
4.00
1.00
8.3
22 kV Danger boards of appropriate size & marking. Nos
6.00
8.4
433 V Danger boards of appropriate size & marking.
1.1 kV grade Rubber matting 1000 mm width.
First Aid Box
Laminated First aid chart with frame.
4.5 Kg fire extinguisher ABC type
9 Kg fire extinguisher ABC type
Fire Buckets with stand 04 Nos. of Buckets filled
with Fine Sand
4
4.1
4.2
5
6
7
8
8.5
8.6
8.7
8.8
8.9
9.0
10.00 HT Cable Route Marker
Supply
Rate
Set
Set
5.00
2.00
job
1.00
BASIC COST Duties and Taxes
Nos. 14.00
job
1.00
Nos
12.00
Mtr
Nos
Nos
Nos
Nos
30.00
3.00
3.00
5.00
5.00
Nos
4.00
Nos
50.00
Page 17 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
HT BOQ
Description
Unit
Qnty
Supply
Rate
1
1.1
2
2.1
2.2
2.3
3
3.1
3.2
Total Of Section-I
SECTION-II ITEM MAY BE EXECUTED
Supply, installation, testing & commissioning of heat
shrink jointing for 22kV HT cables of following
sizes including necessary accessories, spider
supports, plated hardware like lugs / ferrules,
insulation tapes etc. complete. Standard make.
Scope also includes making suitable cutouts in
gland plate & sealing them after connections.
Straight through Joints.
Set
Excavation of cable trenches upto a depth of
1000mm refilling and reinstating the trenches and
removing excess soil after proper 4" sand bedding/
coushioning above & below cables with bricks as per
specifications & IS standards.
Excavation in soil, soft murm & Hard murm.
M3
Excavation in soft Rock.
M3
Excavation in Hard Rock.
M3
Supply, laying of following different types of Hume
pipes/pipes in trenches for road crossing for
electrical, telephone cables etc. complete as
required including excavation of trench in all types
of strata except hard rock and refilling, leveling of
trench, shifting of extra earth or debris to dump
yard complete as required.
300 mm dia. RCC Pipe.
Mtr
200 mm dia. Half round RCC hume Pipe.
Mtr
Total Of Section-II
Note : Rates of Duties, taxes in percentagle and
nature of incidential charges for each item may be
shown at foot note
BASIC COST Duties and Taxes
1.00
1.00
1.00
1.00
1.00
1.00
Page 18 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
DG BOQ
Description
Unit Qnty
Supply
Rate
1.0
2.0
2.1
3.0
3.1
4.0
5.0
5.1
5.2
5.3
5.4
5.5
5.7
SECTION-I
Design, Supply, Installation, Testing & Commissioning at site
3-phase, 415V, 1500RPM, 50 HZ, Diesel generator set as per
DG Technical Document, of 1 x 625 KVA Prime Rating at
0.8 pf lagging diesel engine with Radiator cooled and
alternator set mounted on common base frame in Outdoor
Type Acoustically Treated Enclosure, with day tank of
adequate capacity in liters for backup of 8-10hr running of
DG set, battery, battery charger, return fuel color, anti
vibration mounting pads including residential silencer, engine
alternator safeties with accessories, 1No. of 1000A, 25kA,
mp based, LSIG, MCCB Isolator inside acoustic
enclosure as per the attached SLD, engine control panel,
ventilation system, inside conopy lighting, etc. as per
specification complete as required. DG shall have appropriate
Building Management System integration provisions / ports
as well as hardwired alarm/ critical monitoring provisions
with details of integrationDiesel engine shall conform to
IS:10000 and alternator shall be self excited coanding onto
the structure. paration of mock up etc. complete. (The
density of the foam should be 45 Kg/m3)ms.
They make the pipe design and air flow calculation very
difficult to predict with any accuracy.. Fuel & oil fill for
testing, trial run till handover. All cost of fuel, Oil and
operation shall be borne by the the bidder.
Supply, Installation, Testing & Commissioning of Cu.
Unarmoured cables of following size from Alternator to
1000A MCCB Isolator Panel inside DG Set.
1C X 95 sq.mm. 2XY Cu. UnArm. Cable
(4
Runs/phase + 2 Runs - Neutral)
Cable Termination of above cable
1C X 95 sq.mm. 2XY Cu. UnArm. Cable
Supply Installation testing Commissioning of Synchronisation
cum AMF Panel as per SLD and Technical Document.
Synchronizing panel should be incorporated with Auto Load
sharing, Load Dependent "Start & Stop".
Design Supply, Installation, Commissioing of Exhaust
System as per below mentioned
10"M.S.Pipe Class B from Exhaust Bellow to Silencer
Supply of 10" MS Class B Exhaust pipe
Aluminium Cladding for the Exhaust Pipe
Cladding for the Residential Silencers
Bends & Flanges 250 mm Dia or required size.
Steel for Exhaust Support structure
(for
6No. Of D.G.Sets)
Set
6
Mtrs.
550
Nos
72
Set
1
Mtrs.
Mtrs.
Mtrs.
Nos
Nos
12
50
62
6
6
Ton
4
BASIC COST Duties and Taxes
Page 19 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
DG BOQ
Description
Unit Qnty
Supply
Rate
6.00
a
b
7.0
7.1
7.2
7.3
a
b
7.4
a
7.5
7.6
7.7
7.8
8.0
9.0
9.1
9.2
10.0
10.1
10.2
10.3
10.4
10.5
10.6
11.0
11.1
11.2
11.3
SITC of GI ladder and Perforated Cable Trays of following
sizes
600mm x 75mm ladder tray.
300mm x 50mm perforated tray.
FUEL PIPING
Supply ,Installation and Commissioning of ASTM Grade,
seamless Pipe 40 mm (40NB)
Supply ,Installation and Commissioning of ASTM Grade,
seamless Pipe 25 mm (25NB)
Ball Valve
40NB
25NB
Non Return Valves
40NB
Y Stainers
Solenoid Valves for 25NB tapping lines for auto operation of
Fuel pumping system.
Flow Meter
Hardware for fuel piping
Supply installation of Earthing station as per IS 3043 using
SIP/PIP electrode complete (Eqvt to Ashlok T 39) with
watering pipe & suitable GI strip up to chamber, soil
treatment with suitable backfill powder, brick inspection
chamber with 450x450 mm CI cover, disconnecting link
complete including excavation or earth pit, refilling.
Supply, installation, testing of GI/ Cu. earthing strips & wires
in ground at a depth of 600 mm. in trenches or tray with
necessary clamps & bimetallic srips as per specification.
(excavation required for this to be ensured in the scope.)
Refer layout & tender spec for various applications
50 x 10 mm. GI strip.
50 x 10 mm. Cu strip.
Supply, Installation, Testing and Commissioning of Al./Cu. LT
XLPE cable for Power/Control cabling as mentioned below.
Schedule for the same shall be submitted by the DG Vendor
prior execution of the job.
3.5C X 400 sq.mm. A2XFY
24C X 2.5 sq.mm. 2XWY
2C X 4 sq.mm. 2XWY
6C X 2.5 sq.mm. 2XWY
3C X 1.5 sq.mm. Cu. Sheilded Cable
2C X 2.5 sq.mm. 2XWY
Cable Termination of above cables with glands and lugs.
3.5C X 400 sq.mm. A2XFY
24C X 2.5 sq.mm. 2XWY
2C X 4 sq.mm. 2XWY
Mtrs.
Mtrs.
60
20
Mtrs.
50
Mtrs.
60
Nos
Nos
4
6
Nos
Nos
2
2
Set
6
Nos
Set
6
1
Nos
26
Mtrs.
Mtrs.
200
150
BASIC COST Duties and Taxes
Mtrs. 1950
Mtrs. 650
Mtrs. 500
Mtrs. 500
Mtrs. 1500
Mtrs. 200
Nos
Nos
Nos
36
6
6
Page 20 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
DG BOQ
Description
Unit Qnty
Supply
Rate
11.4
11.5
11.6
13.0
13.1
14
15.1
Nos
6C X 2.5 sq.mm. 2XWY
Nos
3C X 1.5 sq.mm. Cu. Sheilded Cable
Nos
2C X 2.5 sq.mm. 2XWY
Approvals
Approvals and registration from Statutory Authorities like
pollution control board, electrical inspector etc. necessory to
Job
complete the job.
Under Ground Diesel Storage Tank ( UG Tank )
Supply , Installation Testing and commissioning of Under
ground Diesel Storage Tank of Capacity 50 KL including
Approval from CCOE, NOC from various authorities, MPCB,
Fire authority approval and any other statutary bodies
approval. Necessory civil work along with fencing and gate.
In the area of UG tank necessory flame proof light fitting
along with lighting poles to be considered. Necessory
Pumping arrangement (Electrical Driven) with one working
and one stand by pumps, along with Diesel Piping to be
Job
considered. Fuel storage pumping system shall be designed
to have a trouble-free automated system without manual
intervention for auto-filling of Day Tanks for 6No. of DG sets.
Level sensors, flow meters to be considered by bidders.
Monitoring provision shall be included with Potential free
contacts/option to connect Flow Meters inside fuel lines /
Underground Level Sensor Provision on tanks etc which shall
provide for smooth operation.
BASIC COST Duties and Taxes
6
18
2
1
1
TOTAL Of SECTION-I
Page 21 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Client:-IITM,Pune
Project: Proposed Data Centre
Sr. No.
DG BOQ
Description
Unit Qnty
Supply
Rate
1
1.1
2
2.1
3
4
4.1
4.2
5
5.1
5.2
5.3
6
6.4
6.5
6.6
SECTION-II ITEM MAY BE EXECUTED
Design Supply, Installation, Commissioing of Exhaust
System as per below mentioned
Supply, Installation and Commissioning of Single self
supported standalone chimney as common exhaust outlet for
3Nos. Of DG Sets with all related & required accessories,
Job
support structure, LA, Aviation lamp etc.
SITC of GI ladder and Perforated Cable Trays of following
sizes
Mtrs.
750mm x 75mm ladder tray.
Supply , Installation , Testing and Commissioing external
Fuel Tank of suitable capacity 990 lts as per CPCB norms.
Job
Supply, Installation, Testing and Commissioning of Earthing
station as per IS 3043 using Pipe / plate electrode complete
with 50mm dia. watering pipe & suitable GI/Cu strip up to
chamber, soil treatment with charcoal and salt / bentonite
powder, brick inspection chamber with 450x450 mm CI
cover, disconnecting link complete including rate of
excavation for earth pit, refilling and any other item required
to complete the task.
Earthing station as above but using 600 x 600 x 6 mm. GI.
Nos
Plate as electrode complete.
Earthing station as above but using 600 x 600 x 3 mm. Cu.
Nos
Plate as electrode complete.
Supply, Installation, Testing and Commissioning of Al./Cu. LT
XLPE cable for Power/Control cabling as mentioned below.
Schedule for the same shall be submitted by the DG Vendor
prior execution of the job.
Mtrs.
10C X 2.5 sq.mm. 2XWY
Mtrs.
4C X 25 sq.mm.
Mtrs.
3C X 4 sq.mm. 2XWY
Cable Termination of above cables with glands and lugs.
Nos
10C X 2.5 sq.mm. 2XWY
Nos
4C X 25 sq.mm.
Nos
3C X 4 sq.mm. 2XWY
TOTAL Of SECTION-II
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot note
BASIC COST Duties and Taxes
1
1
1
1
1
1
1
1
1
1
1
Page 22 of 60
Installation
Total
Rate
BASIC COST
Taxes
Total
Sr. No.
Description
Unit Qnty
PRICISION CHILLERS
1
Supply, installation, testing & commissioning of 175 TR 'TWIN
SCREW' type Air-cooled liquid chillers, complete with spring
loaded anti vibration mounts, With first charge of Refrigerant Gas,
Lubricating oil etc., for the following operating conditions. The
chillers shall be complete with screw compressors (Single / Multi
Screw), Fin and Tube Air cooled condensers, Flooded evaporator,
Drive Motor, Control panel etc., Star delta Starter, stepless
capacity control, etc.,as per specifications mentioned in the
technical specification sheet. The Chiller shall be capable of
opearting in open ambient temperature of local ambient of Pune
City, and shall use R-134 a Refrigerant. The Chiller should be
installed on Spring Mounted Antivibration mounts.Chiller shall be
suitable for 45 deg.C abmient temp.with starting to full load timing
as 3.0 min. maximum.
1.1. Cooling Capacity (175 TR x 4 Nos) (2 W + 2 SB)
Chiller Flow rate : 335 US GPM Chiller tubes to be designed
for the above flow rate.
Fouling Factor : 0.0005 ~ 0.0001
IKW/TR : 1.25 ~ 1.36 Kw/TR
EWT :
12.00 Deg C
LWT :
7.00 ° C
EER ratio (To be Furnished with technical bid)
OR
Nos
4
Supply
Installation
Rate BASIC COST Duties and Taxes Total Rate BASIC COST Taxes Total
Supply, installation, testing & commissioning of 175 TR 'TWIN
SCREW' type Air-cooled liquid chillers, complete with spring
loaded anti vibration mounts, With first charge of Refrigerant Gas,
Lubricating oil etc., for the following operating conditions. The
chillers shall be complete with screw compressors (Single / Multi
Screw), Fin and Tube Air cooled condensers, Flooded evaporator,
Drive Motor, Control panel etc., Star delta Starter, stepless
capacity control, etc.,as per specifications mentioned in the
technical specification sheet. The Chiller shall be capable of
opearting in open ambient temperature of local ambient of Pune
City, and shall use R-134 a Refrigerant. The Chiller should be
installed on Spring Mounted Antivibration mounts.Chiller shall be
suitable for 45 deg.C abmient temp.with starting to full load timing
as 3.0 min. maximum.
1.2 Cooling Capacity (175 TR x 4 Nos) (2 W + 2 SB)
Chiller Flow rate : 335 US GPM Chiller tubes to be designed
for the above flow rate.
Fouling Factor : 0.0005 ~ 0.0001
IKW/TR : 1.25 ~ 1.36 Kw/TR
EWT :
20.00 Deg C
LWT :
14.00 ° C
EER ratio (To be Furnished with technical bid)
TOTAL VALUE FOR CHILLERS
2
CENTRIFUGAL PUMPS
Nos
4
2.1
Supply of Chilled water pump, End Suction Back pull out type
horizontal , Single Stage Pumps, running at 2900 rpm bareshaft
fitted with drip tight Make mechanical seal with O ring silicone
carbide seat retainer. along with accessories like fabricated MS
base frame , coupling guard , foundation bolts , flexible spacer
coupling & coupled to foot mounted TEFC three phase motor (
EFF-1 ) , Class F insulation & IP 55 protection of suitable rating.
The motor shall be compatible with VFD drive as specified in the
enquiry document. Pump design parameters to be designed as
follows. Flexible bellows at pump inlet and pump outlet as per
suction and delivery sizes to be considered in the rate.
Metallurgy:
Body : Cast Iron (IS 210 FG260), Impeller : LT Bronze (IS 318
Grade LTB2), Shaft : SS 410, Shaft Sleeve : SS 410
Pump design parameters to be designed as follows.
Primary chilled water pump module
Flow rate : 335 US GPM @ 35 Mtr head required as per site
Nos
condition. (2W+2SB).
2.2
Control Panel consisting of Panel + VFD (Common for both
pumps) housed in a single enclosure with incomer and two nos
outgoing feeder. The terminations shall be suitable as per cable. Nos
Please read the control panel logic in technical specification
section.
TOTAL VALUE FOR PUMPS
3
CHILLED WATER SYSTEM
4
1
3.1
3.1.1
3.1.2
3.1.3
3.1.4
3.1.5
3.1.7
3.1.8
3.1.9
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.1.7
5
6
Supply, installation, testing & commissioning of Polyethylene High
Density (PE 100) from +GF+ piping of PN-16 with all necessary
GF Elctronic Fusion welding/Victaulic Fitting only such as
Couplings, Bends, Reducers, T, expanders, flanges etc, supports
such as u clamps, threaded rod, pre insulated pedestals, nut and
washers as per site condition and 19 thick Closed cell rubber
nitrile of Class "O". The insulation of shall be covered with 26 G
aluminium cladding with superior workmanship.
250 mm Dia
200 mm Dia
150 mm Dia
100 mm Dia
80 mm Dia
65 mm Dia
40 mm Dia
32mm Dia
RMT
RMT
RMT
RMT
RMT
RMT
RMT
RMT
405
250
RO
75
75
40
RO
150
Nos
Nos
Nos
Nos
Nos
Nos
Nos
15
30
35
8
32
4
R.O.
Nos
Nos
4
2
Centric Disc Butterfly valve with a single piece Rubber lined body.
Short Wafer body. Integrally moulded seat. Rating PN 16.
General design and manufacturing as per API 609 category A/BS
5155/MSS SP-67. Flange ANSI 150 , properly insulated with 25
mm rubber nitrile class O closed cell insulation with 26G Al.
cladding.
250 mm Dia
200 mm Dia
150 mm Dia
100 mm Dia
80 mm Dia
65 mm Dia
40 mm Dia
Flow Switch suitable for 200 mm Dia Pipe
Diferential pressure switch suitable for 200 mm Dia Pipe
7
8
100 mm dia dial type pressure gages with needle valve & as per
specifications mentioned in technical data sheet. Pressure gauge,
scale range 0-10 bar. Complete with 3 valves an piping. To be
mounted over all pumps. Size 10 DN
100 mm dia dial type pressure gages with needle valve & as per
specifications mentioned in technical data sheet.
Nos
4
Nos
8
9
Dial type industrial type imported thermometer with 100mm dia
dial & as per specifications mentioned in technical data sheet
Nos
8
10
Chiller Inlet & Outlet Rubber Expansion Bellows - 200 mm Dia
Nos
8
11
Supply, Installation of ball valve CS body SS 304 Ball full three
Nos
piece design full port end connection socket weld type class # 150.
6
15 mm Dia Nos
25 mm Dia Nos
32 mm Dia Nos
6
12
92
11.1
11.2
11.3
12
Balancing valve with measurement points (STA-D). Pressure class
PN 16. Made up of AMETAL, Seat seal: Stem with EPDM O-ring
Spindle seal: EPDM O-ring
Handwheel: Polyamide and TPE.
12.1
12.2
25 mm Dia Nos
200 mm Dia Nos
Flanged Balancing Valve With measurement points (STAF - SG).
Pressure class PN 16.
Body: Ductile iron EN-GJS-400-15.
13
spindle of AMETAL
Seat seal: Cone with EPDM ring.
Bonnet bolts: Chromed steel.
13.1
200 mm Dia
14
14
46
R.O.
Nos
2
200 mm Dia Nos
4
Nos
8
SITC of Y-Strainer of following sizes;
Automatic Air vent of 1/2 "
15
Closed Expansion Tank with Expansion Vessel and pressurizing
Pumps 1 Working + 1 Standby. The tank capacity to be 1000 Ltr .
Expansion tank to be of SS 309 with Armaflex / K- Flex Insulation
32 mm thick & 26 Gage Aluminum Cladding with diamond finish
and with related piping, Isolating valves , Safety valves , Drains, Nos
Overflow and Guages.6.3 thik
Pressurisation unit with double pump(0.85HP) 230V, 50Hz,
single phase) pressure transmitter, IP65 control panel(Remote
operation, Duty cycling, Dry-Run protection)
16
Centrifugal Air Separator for Chilled Water in SS 309 Tank shall
be insulated with Armaflex / K Flex insulation 32 mm & 26 Gage
Aluminum Cladding with diamond finish and necessary valves
etc.suitable for the following flow rates.6.3Thik
16.1
Suitable to mount on 250 mm Dia pipe Nos
1
2
17
SITC of chemical dosing plant suitable for above system for
flushing and treating the water including following
1. 500 Ltr make up water storage tank x 01 nos
2. FIrst charge of Dosing chemicals for the commissioning of the
system and chemicals for the 6 months operation.
3. Treated water tank of capacity 2000 Ltr. Interconnecting piping,
accessories and valves complete in all respect. 25 mtr of 25 NB
size pipe to be considered as interconnecting pipe. 03 Nos of ball
velves and 02 nos of ball float vales to be considered in the item.
Lot
1
18
SITC of SS 309 tank with capacity of 15000 Ltr to be used as
thermal storage for 10 mins back up supply. The tank to be of M S
Construction and with anti corrosive coating from inside with
Armaflex / K- Flex Insulation 32 mm thick & 26 Gage Aluminum
Cladding with diamond finish and with related piping, Isolating
valves , Safety valves , Drains, Overflow and Guages. 8 mm Shell
thickness and 12 mm Dish thickness. The tank shall have
necessary ports with flanges Table F
Lot
2
19
SITC of cooling distribution unit (CDU) to provide cooling water
close control and above the dew point. Shall be capable of 150
KW cooling capacity. The CDU shall be approved to work with IBM
'iDataPlex / RDHX' racks.
Nos
It shall have full run and stand by capabilities with redundant
pumps. It shal have internalmanifold with leak free quick release
couplings. It shall have a auto fill and bleed off connection. FUll
alarm monitoring and connectivity to MODBUS. Complete in all
respect.
8
20
Structural steel such as Channel, Angles, Plates, I section, Beam
section etc with two coats of red oxide and two coats of synthetic
enamale quick drying paint. The colour shall be approved by the
Architect.
Ton
5
150 mm Dia
Nos
4
0
0
100 mm Dia
Nos
4
0
0
21
22
Flanged "Y "Type starainer with SS mesh .
Pressure class PN 16.
Body: Ductile iron
Non return valves
SITC of Flexible hose made of Ethylene Propylene Diene
Monomer (EPDM) rubber - peroxide cured, non-metal oxide
material and shall have Fluid quick-connect couplings at each end.
the couplings must be compatible with the heat exchanger
couplings.
Rmt
Dia 32 mm
TOTAL VALUE FOR CHILLED WATER PIPING
21
21.1
ELECTRIFICATION WORK
Electrical Panel No 1 - 3 : Chiller panel
225
HVAC Utility Panels comprising of 1 Incoming Feeder (4 Pole ,400
Amp with Overload Earth Fault and Short Circuit protection, MCCB
and Outgoing Feeders as per SLD, The Panel shall be IP-55
Protection for Indoor use,duly powder coated by 7 tank painting
process & fabrication of 14/16 Gauge CRCA Sheet.Panel kWH
NOS
meter, R-Y-B indication Lamps, Control Fuses & AL Bus Bar.
Feeders complete with MCCB, Push Buttons, ON, OFF, & Trip
indication,and BMS connectivity etc. Location: Panel Room, with
bottom entry. The panel should be with appropriate cooling/heating
arrangement. Supplier to furnish the power/Heat loass calculation.
and outgoing feeder as below
4
Outgoing Feeder:- As per SLD
21.2
Electrical Panel No 4 - 7, Chiller Pump panel
HVAC Utility Panels comprising of 1 Incoming Feeder (4 Pole ,40
Amp with Overload Earth Fault and Short Circuit protection, MCCB
and Outgoing Feeders as per SLD, The Panel shall be IP-55
Protection for Indoor use,duly powder coated by 7 tank painting
process & fabrication of 14/16 Gauge CRCA Sheet.Panel kWH
NOS
meter, R-Y-B indication Lamps, Control Fuses & AL Bus Bar.
Feeders complete with MCCB, Push Buttons, ON, OFF, & Trip
indication, BMS connectivity etc. Location: Panel Room, with
bottom entry. The panel should be with appropriate cooling/heating
arrangement. Supplier to furnish the power/Heat loass calculation.
and outgoing feeder as below
Outgoing Feeder:- As per SLD
21.3
Electrical Panel No 8, Pump Panel
4
HVAC Utility Panels comprising of 1 Incoming Feeder (4 Pole ,40
Amp with Overload Earth Fault and Short Circuit protection, MCCB
and Outgoing Feeders as per SLD, The Panel shall be IP-55
Protection for Indoor use,duly powder coated by 7 tank painting
process & fabrication of 14/16 Gauge CRCA Sheet.Panel kWH
NOS
meter, R-Y-B indication Lamps, Control Fuses & AL Bus Bar.
Feeders complete with MCCB, Push Buttons, ON, OFF, & Trip
indication etc. Location: Panel Room, with bottom entry. The
panel should be with appropriate cooling/heating arrangement.
Supplier to furnish the power/Heat loass calculation. and outgoing
feeder as below
1
Outgoing Feeder:- As per SLD
21.4
Electrical Panel No 9-11, PAC panel.
HVAC Utility Panels comprising of 1 Incoming Feeder (4 Pole ,100
Amp with Overload Earth Fault and Short Circuit protection, MCCB
and Outgoing Feeders as per SLD, The Panel shall be IP-55
Protection for Indoor use,duly powder coated by 7 tank painting
process & fabrication of 14/16 Gauge CRCA Sheet.Panel kWH
NOS
meter, R-Y-B indication Lamps, Control Fuses & AL Bus Bar.
Feeders complete with MCCB, Push Buttons, ON, OFF, & Trip
indication, BMS connectivity etc. Location: Panel Room, with
bottom entry. The panel should be with appropriate cooling/heating
arrangement. Supplier to furnish the power/Heat loass calculation.
and outgoing feeder as below
22
22.3.1
22.3.2
22.3.3
22.3.4
22.3.5
22.3.6
Outgoing Feeder:- As per SLD
Supply and installation of prefabricated (hot dip Galvanised ) G.I.
ladder/ perforated trays with 50/ 75 mm C channels & Runges at
200mm cc and including prefabricated accessories like Bends,
Tee, Right-angles & tray coupling arrangement etc.(Bends
fabricated at site will not be allowed.)
50mm, 50x50 perforated tray. (16 SWG)
100mm, 50x50 perforated tray. (16 SWG)
150mm, 50x50 perforated tray. (16 SWG)
200mm, 50x50 perforated tray. (16 SWG)
300 mm, 50x50 perforated tray. (14 SWG)
450 mm, 50x50 perforated tray. (14 SWG)
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
1
65
22.3.7
22.3.8
22.3.9
22.3.10
23
23.4.1
23.4.2
23.4.3
23.4.4
23.4.5
23.4.6
24
600 mm, 50x50 perforated tray. (14 SWG)
450 mm, 75x75 Ladder tray. (14 SWG)
600 mm, 75x75 Ladder tray. (14 SWG)
750 mm, 75x75 Ladder tray. (14 SWG)
Rmt.
Rmt.
Rmt.
Rmt.
50
Cable Tray Covers suitable for following size trays
50mm perforated tray.
100mm perforated tray.
150mm perforated tray.
200mm, perforated tray.
300 mm perforated tray.
450 mm perforated tray.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
R.O.
R.O.
R.O.
R.O.
R.O.
R.O.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
Rmt.
R.O.
600
R.O.
R.O.
R.O.
R.O.
R.O.
R.O.
375
R.O.
R.O.
R.O.
R.O.
350
R.O.
R.O.
600
R.O.
R.O.
R.O.
75
Supply, Installation, Testing and Commissioning of 1100V grade
L.T. XLPE/ PVC insulated multistrand Al./ Cu. conductor cables on
provided prefabricated trays/ pipe/ in trenches with necessary
clamps, identification tag. & all other items required to complete
the task. (Actual cable lengths shall be measured at site prior to
procurement. )
24.6.1
24.6.2
24.6.3
24.6.4
24.6.5
24.6.6
24.6.7
24.6.8
24.6.9
24.6.10
24.6.11
24.6.12
24.6.13
24.6.14
24.6.15
24.6.16
24.6.17
24.6.18
24.6.19
24.6.20
3.5C x 400 Sq.mm. A2XFY Cable.
3.5C x 300 Sq.mm. A2XFY Cable.
3.5C x 240 Sq.mm. A2XFY Cable.
3.5C x 185 Sq.mm. A2XFY Cable.
3.5C x 150 Sq.mm. A2XFY Cable.
3.5C x 120 Sq.mm. A2XFY Cable.
3.5C x 95 Sq.mm. A2XFY Cable.
3.5C x 70 Sq.mm. A2XFY Cable.
3.5C x 50 Sq.mm. A2XFY Cable.
3.5C x 35 Sq.mm. A2XFY Cable.
3.5C x 25 Sq.mm. A2XFY Cable.
4C x 25 Sq.mm. AYFY Cable.
4C x 10 Sq.mm. YWY Cable.
4C x 16 Sq.mm. YWY Cable.
4C x 6 Sq.mm. YWY Cable.
4C x 4 Sq.mm. YWY Cable.
4C x 2.5 Sq.mm. AYFY Cable.
3C x 6 Sq.mm. YWY Cable.
3C x 4 Sq.mm. YWY Cable.
3C x 2.5 Sq.mm. YWY Cable.
25
25.7.1
25.7.2
25.7.3
25.7.4
25.7.5
25.7.6
25.7.7
25.7.8
25.7.9
25.7.10
25.7.11
25.7.12
26
26.8.1
26.8.2
26.8.3
26.8.4
26.8.5
26.8.6
26.8.7
27
Supply & installation of End termination for cables as above with
Brass, heavy duty, Single compression glands, lugs, other
consumable, crimping, gland hole drilling, ferrulling, marking, etc.
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Nos
R.O.
12
R.O.
R.O.
R.O.
R.O.
8
R.O.
8
R.O.
R.O.
R.O.
3.5C x 400 Sq.mm. A2XFY Cable.
3.5C x 300 Sq.mm. A2XFY Cable.
3.5C x 240 Sq.mm. A2XFY Cable.
3.5C x 185 Sq.mm. A2XFY Cable.
3.5C x 150 Sq.mm. A2XFY Cable.
3.5C x 120 Sq.mm. A2XFY Cable.
3.5C x 95 Sq.mm. A2XFY Cable.
Nos
Nos
Nos
Nos
Nos
Nos
Nos
R.O.
16
R.O.
R.O.
R.O.
R.O.
R.O.
Supply, laying and connection of copper earthing 25mm x 3mm
thick copper strip.
Rmt
150
3.5C x 70 Sq.mm. A2XFY Cable.
3.5C x 50 Sq.mm. A2XFY Cable.
3.5C x 35 Sq.mm. A2XFY Cable.
3.5C x 25 Sq.mm. A2XFY Cable.
4C x 16 Sq.mm. AYFY Cable.
4C x 10 Sq.mm. YWY Cable.
4C x 16 Sq.mm. YWY Cable.
4C x 4 Sq.mm. YWY Cable.
4C x 2.5 Sq.mm. YWY Cable.
3C x 6 Sq.mm. YWY Cable.
3C x 4 Sq.mm. YWY Cable.
3C x 2.5 Sq.mm. YWY Cable.
Supply & installation of End termination for cables as above with
Brass, heavy duty, Double compression glands, lugs, other
consumable, crimping, gland hole drilling, ferrulling, marking, etc.
TOTAL VALUE FOR ELECTRIFICATION WORK
SUB TOTAL OF HVAC SYSTEM
-
Note : Rates of Duties, taxes in percentagle and nature of incidential
charges for each item may be shown at foot note
Sr.
No.
BOQ HVAC WORKS - PAC
Unit Qnty
Description
Rate
Supply of Precision AC as per the technical specification.
(2W+1SB)
1.1
30 TR Net Cooling Capacity
EER ratio (To be Furnished with technical bid)
Data Centre
Supply
BASIC COST Duties and Taxes
Installation
Total
Rate
BASIC COST
Taxes
Total
1
2
Refrigerant Piping as per manufacturing standard with armaflex 25
mm thk rubber nitrile insulation.Piping shall be routed via suitable
size cable try. The distance between the IDU and ODU shall be 20
RMT ea only.
Nos
3
LOT
1
PVC drain piping. Insulated with 13 mm rubber nitrile armaflex
insulation. The pipe shall be of finolex make only.
3.1
40 mm RMT
80
4
GI Class B, ERW pipe for fresh water
4.1
60
3
25 NB RMT
5
Refrigerant gas R 407 C as per manufacturers specification and quantity
LOT
3
6
Deep pleated 4" filters with an ASHRAE 52.2 MERV 8 rating (Spare) Lot
3
7
Fan Aided Floor Grills in front of Tape Library (600x600mm). To
be used as floor diffuser in powder coated MS construction. The
Diffuser shall be able to take a load of 1000 Kg UDL. The top shall
have an anti static coating.
8.1
8.2
8.3
8.4
SITC of GI Ducting (180 GSM) Factory Fabricated with Duct Mate
Flanges as per SMACNA for supply air, with 19 mm insulation of
Closed Cell Rubber Nitrile Armaflex/Kflex/Sekisui pilon
make.inclussive of supports 10 mm GI Threaded rod and C
channel 25x25x25 mm size, As per site condition.
18 guage
20 guage
22 guage
24 guage
9
SITC of Aluminum eggcrate powder coated return air grill with
aluminum border and grid in in ½ x ½ x ½-inch sizes.
8
9.1
Nos
14
SQM R.O
SQM R.O.
SQM R.O.
SQM 20
600 mm X 600 mm Nos R.O.
TOTAL VALUE FOR PAC
TOTAL
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot note
Doc.No:
T_705_IITM_BQ00
Page 35 of 60
Rev 00
IITM, Pashan, Pune
Data Centre
BOQ - HVAC
Sr.
No.
Description
Unit Qnty
Rate
BASIC COST
Supply
Duties and Taxes
Total
Rate
Installation
BASIC COST Taxes
Total
PART-A ' LOW STATIC DUCTABLE SPILT SYSTEM '
The system should be with necessary IDU's & ODU's.Out Door Unit shall be
complete with Invertor/ scroll compressor, The system should be with
necessary combinations of IDU's & ODU's along with necessary
interconnecting refrigerant piping, Cabling, Drain Piping, Drain pumps,
Flexible connection of fire retardant type, etc. of followings capacities, The
ODU Shall be of Top discharge type.The refrigerat shall be R407 C, R410
Aonly.
1
Supply ,Installation And commissioning of following Ductable Type Low static
Split Units including indoor - Outdoor Combination, Refergerant Charge as
per piping Insttalation, IDU & ODU Supports (ODU Support with painted MS
Channel of suffient size). The unit shall be with necessary corded remote and
the holder for the same.
1.1 10 TR / 4000 CFM Capacity
EER ratio (To be Furnished with technical bid)
Nos
4
RMT
RMT
RMT
RMT
RMT
RMT
RMT
R.O.
R.O.
R.O.
R.O.
200
R.O.
R.O.
Rmt.
135
Refrigerant Piping with 19 mm thick Closed Cell rubber nitrile,Class "O"armaflex insulation of following sizes- Inclussive of necessary Supports as
per standard practices.Piping shall be routed via suitable size cable try
2
2.1
2.2
2.3
2.4
2.4
2.5
2.6
Gas Line (inch.)
41.3
34.9
34.9
28.6
22.2
12.7
15.9
Liquid Line (inch.)
19.1
19.1
15.9
12.7
6.4
6.4
6.4
3
Interconnecting control cabling between IDU's & ODU's. The cabling shall be
well supported / tied up with the ref line.
4
Acoustical insulation with Armaflex/ K flex / Sekisui open cell sound
insulation.Armasound/eq.super sileance duct lianer with micro ban, open cell, SQM
elastomaric nitrile rubber.
5
5.1
5.2
5.3
SLC of Drain Piping shall be HARD PVC . Drain Piping shall be insulated 13
mm Armaflex rubber nitrile closed cell insulation. The drain shall be released
into the nearest toilets or as instructed by consulting engineer.
50 mm dia. Rmt.
40 mm dia. Rmt.
25 mm dia. Rmt.
Doc.No:
T_ME_HVAC_BQ01
15
0
20
40
Page 36 of 60
Rev 00
IITM, Pashan, Pune
Data Centre
BOQ - HVAC
SITC of GI Ducting (120 GSM) Factory Fabricated with Duct Mate Flanges as
per SMACNA for supply air, with 19 mm insulation of Closed Cell Rubber
Nitrile Armaflex/Kflex/Sekisui pilon make.inclussive of supports 10 mm GI
Threaded rod and C channel 25x25x25 mm size, As per site condition.
6
6.1
6.2
6.3
6.4
18
20
22
24
guage
guage
guage
guage
SQM
SQM
SQM
SQM
R.O
R.O.
R.O.
40
7
Supply air grille with adjustable horizontal and vertical vanes, made of white
painted steel, with mounting frame and air volume damper made of
galvanized steel sheet.
SQM
2
8
Pressure Testing, Nitrogen flushing, gas charging,& commissioning testing of
the air conditioning system.
Lot
1
9
SITC of auto chnageover timer for cyclic operation of ductable units as a
combination of 2 W + 2 SB. Each unit shall run for 8 hrs.
Nos
1
Nos
2
Supply ,Installation And commissioning of following Hi-wall Type Split Units
including indoor - Outdoor Combination, Refrigerent piping and
10 Interconnecting control cabling of 15 Mtr. length, Refergerant Charge as per
piping Insttalation, Automatic Timer of 4 Hrs. Cycle, IDU & ODU Supports as
per std. Practice, And must be atleast 5- Star rated
10.1 1.5 TR High Wall Unit (1W+1 SB) BMS Room
TOTAL VALUE FOR AIR CONDITIONING WORK (PART"A")
Note : Rates of Duties, taxes in percentagle and nature of incidential charges
for each item may be shown at foot note
Doc.No:
T_ME_HVAC_BQ01
0
Page 37 of 60
Rev 00
0
IITM, Pashan, Pune
Data Centre
BOQ - HVAC
Sr.
No.
Description
Unit Qnty
Rate
PART-A ' LOW STATIC DUCTABLE SPILT SYSTEM '
1
2.1
2.2
2.3
2.4
2.4
2.5
2.6
Nos
2
Gas Line (inch.)
41.3
34.9
28.6
28.6
22.2
12.7
15.9
Liquid Line (inch.)
19.1
19.1
15.9
12.7
12.7
6.4
6.4
RMT
RMT
RMT
RMT
RMT
RMT
RMT
R.O.
R.O.
R.O.
R.O.
50
R.O.
R.O.
Interconnecting control cabling between IDU's & ODU's. The cabling shall be
well supported / tied up with the ref line.
Rmt.
50
4
Acoustical insulation with Armaflex/ K flex / Sekisui open cell sound
insulation.Armasound/eq.super sileance duct lianer with micro ban, open cell,
elastomaric nitrile rubber.
SQM
5
5.1
5.2
5.3
Total
Rate
Installation
BASIC COST
Taxes
Refrigerant Piping with 19 mm thick Closed Cell rubber nitrile,Class "O"armaflex insulation of following sizes- Inclussive of necessary Supports as per
standard practices.Piping shall be routed via suitable size cable try
3
5
Supply
Duties and Taxes
The system should be with necessary IDU's & ODU's.Out Door Unit shall be
complete with Invertor/ scroll compressor, The system should be with
necessary combinations of IDU's & ODU's along with necessary
interconnecting refrigerant piping, Cabling, Drain Piping, Drain pumps, Flexible
connection of fire retardant type, etc. of followings capacities, The ODU Shall
be of Top discharge type.The refrigerat shall be R407 C, R 410 Aonly.
Supply ,Installation And commissioning of following Ductable Type Low static
Split Units including indoor - Outdoor Combination, Refergerant Charge as per
piping Insttalation, IDU & ODU Supports (ODU Support with painted MS
Channel of suffient size). The unit shall be with necessary corded remote and
the holder for the same.
1.1 5 TR / 2000 CFM Capacity
EER ratio (To be Furnished with technical bid)
2
BASIC COST
SLC of Drain Piping shall be HARD PVC . Drain Piping shall be insulated 13 mm
Armaflex rubber nitrile closed cell insulation. The drain shall be released into
the nearest toilets or as instructed by consulting engineer.
50 mm dia. Rmt.
40 mm dia. Rmt.
25 mm dia. Rmt.
Doc.No:
T_ME_HVAC_BQ02
R.O
20
R.O
Page 38 of 60
Rev 00
IITM, Pashan, Pune
Total
BOQ - HVAC
6
Data Centre
SITC of GI Ducting (120 GSM) Factory Fabricated with Duct Mate Flanges as
per SMACNA for supply air, with 19 mm insulation of Closed Cell Rubber Nitrile
Armaflex/Kflex/Sekisui pilon make.inclussive of supports 10 mm GI Threaded
rod and C channel 25x25x25 mm size, As per site condition.
6.1
6.2
6.3
6.4
18
20
22
24
guage
guage
guage
guage
SQM
SQM
SQM
SQM
R.O
R.O.
R.O.
15
7
Door Louver in extruded AL consutruction. The Grill shall be powder coated.
The color shall be approved by the architect / consulting engineer before the
delivery at site.
SQM
0.5
8
Supply air grille with adjustable horizontal and vertical vanes, made of white
painted steel, with mounting frame and air volume damper made of
galvanized steel sheet.
SQM
1
9
Propeller fan of capacity 500 CFM for exhaust. The fan shall be Industrial type
and shall have safety grill at inlet and mesh at outlet to prevent any bird
entry.
4 P, 1400 RPM, single phase, Motor IP 54 Protection, F Class insulation, Motor
0.12 KW (For Batery room Exhaust provision)
Nos
1
10
Pressure Testing, Nitrogen flushing, gas charging,& commissioning testing of
the air conditioning system.
Lot
1
11
SITC of auto chnageover timer for cyclic operation of ductable units as a
combination of 1W + 1 SB. Each unit shall run for 8 hrs.
Nos
1
TOTAL VALUE FOR AIR CONDITIONING WORK (PART"A")
Note : Rates of Duties, taxes in percentagle and nature of incidential charges
for each item may be shown at foot note
Doc.No:
T_ME_HVAC_BQ02
Page 39 of 60
Rev 00
IITM, Pashan, Pune
BOQ - HVAC
Sr.
No.
Description
Unit Qnty
Supply
Rate
1
2.1
2.2
2.3
2.4
2.4
2.5
2.6
Nos
2
Gas Line (inch.)
41.3
34.9
34.9
28.6
22.2
12.7
15.9
Liquid Line (inch.)
19.1
19.1
15.9
12.7
12.7
6.4
6.4
RMT
RMT
RMT
RMT
RMT
RMT
RMT
R.O.
R.O.
R.O.
R.O.
110
R.O.
R.O.
Interconnecting control cabling between IDU's & ODU's. The cabling shall be
well supported / tied up with the ref line.
Rmt.
50
4
Acoustical insulation with Armaflex/ K flex / Sekisui open cell sound
insulation.Armasound/eq.super sileance duct lianer with micro ban, open cell,
elastomaric nitrile rubber.
SQM
5
5.1
5.2
5.3
Installation
Total
Rate
BASIC COST
Taxes
Refrigerant Piping with 19 mm thick Closed Cell rubber nitrile,Class "O"armaflex insulation of following sizes- Inclussive of necessary Supports as
per standard practices.Piping shall be routed via suitable size cable try
3
5
BASIC COST Duties and Taxes
PART-A ' LOW STATIC DUCTABLE SPILT SYSTEM '
The system should be with necessary IDU's & ODU's.Out Door Unit shall be
complete with Invertor/ scroll compressor, The system should be with
necessary combinations of IDU's & ODU's along with necessary
interconnecting refrigerant piping, Cabling, Drain Piping, Drain pumps,
Flexible connection of fire retardant type, etc. of followings capacities, The
ODU Shall be of Top discharge type.The refrigerat shall be R407 C, R410 A
only.
Supply ,Installation And commissioning of following Ductable Type Low static
Split Units including indoor - Outdoor Combination, Refergerant Charge as
per piping Insttalation, IDU & ODU Supports (ODU Support with painted MS
Channel of suffient size). The unit shall be with necessary corded remote and
the holder for the same.
1.1 10 TR / 4000 CFM Capacity
EER ratio (To be Furnished with technical bid)
2
Data Centre
SLC of Drain Piping shall be HARD PVC . Drain Piping shall be insulated 13
mm Armaflex rubber nitrile closed cell insulation. The drain shall be released
into the nearest toilets or as instructed by consulting engineer.
50 mm dia. Rmt.
40 mm dia. Rmt.
25 mm dia. Rmt.
Doc.No:
T_ME_HVAC_BQ03
R.O
20
R.O
Page 40 of 60
Rev 00
IITM, Pashan, Pune
Total
BOQ - HVAC
6
Data Centre
SITC of GI Ducting (120 GSM) Factory Fabricated with Duct Mate Flanges as
per SMACNA for supply air, with 19 mm insulation of Closed Cell Rubber
Nitrile Armaflex/Kflex/Sekisui pilon make.inclussive of supports 10 mm GI
Threaded rod and C channel 25x25x25 mm size, As per site condition.
6.1
6.2
6.3
6.4
18
20
22
24
guage
guage
guage
guage
SQM
SQM
SQM
SQM
R.O
R.O.
R.O.
20
7
Door Louver in extruded AL consutruction. The Grill shall be powder coated.
The color shall be approved by the architect / consulting engineer before the
delivery at site.
SQM
0.5
8
Supply air grille with adjustable horizontal and vertical vanes, made of white
painted steel, with mounting frame and air volume damper made of
galvanized steel sheet.
SQM
2
9
Propeller fan of capacity 250 CFM for Fresh AIr. The fan shall be Industrial
type and shall have safety grill at inlet and mesh at outlet to prevent any bird
entry.
4 P, 1400 RPM, single phase, Motor IP 54 Protection, F Class insulation, Motor
0.12 KW (For Electrical room FA provision)
Nos
1
10
Pressure Testing, Nitrogen flushing, gas charging,& commissioning testing of
the air conditioning system.
Lot
1
11
SITC of auto chnageover timer for cyclic operation of ductable units as a
combination of 1W + 1 SB. Each unit shall run for 8 hrs.
Nos
1
TOTAL VALUE FOR AIR CONDITIONING WORK (PART"A")
Note : Rates of Duties, taxes in percentagle and nature of incidential charges
for each item may be shown at foot note
Doc.No:
T_ME_HVAC_BQ03
Page 41 of 60
Rev 00
IITM, Pashan, Pune
Data Centre
BoQ - FIRE ALARM SYSTEM
Sr.
No.
Description
Unit Qnty
Rate
Fire Alarm System
1.0
Supply, installation, testing & commissioning
of
Networkable 1 Single Loop Intelligent
Analogue
Addressable Fire Alarm Control Panel with minimum 80
Nos
characters LCD display including Bacnet Gateway for
Integration with BMS System, The panel shall have the
facility to be networked with other panel.
1
2.0
Supply, installation, testing & commissioning of Analogue
Addressable Multi-Sensor detectors combined (Optical +
Nos
thermal) with including detector mounting base &
required accessories.
29
3.0
4.0
5.0
6.0
Doc No:
IITM_802_BQ01_00
Supply, installation, testing & commissioning of
Addressable Manual Call Points (Pull Station Type). The
same shall be square in shape & made of ABS plastic
material. Surface / Flush Mounting. It shall have a "Break
glass" message embedded on the glass. The addressable Nos
module shall be enclosed along with the break glass in a
junction box & with required accessories.
Supply, installation, testing & commissioning of
Conventional Strobe cum Sounder. The strobe cum
sounder shall be made of ABS plastic material & have the
Nos
Db level of minimum 90dBs and a multi tone facility, wall
/ ceiling mounted with mounting base & required
accessories.
Supply, installation, testing & commissioning of
Addressable Monitor Module for Beam Detectors with Nos
Surface / wall mounting box & required accessories. (UL
Approved)
Supply, installation, testing & commissioning of
Addressable Control Module with surface/ wall mounting Nos
box & required accessories (for sounders, strobe light
& strobe cum sounders)
BASIC COST
Supply
Duties and Taxes
Total
Rate
Installation
BASIC COST
Taxes
Total
5
5
RO
RO
Page 42 of 60
Rev 00
IITM, Pashan, Pune
Data Centre
BoQ - FIRE ALARM SYSTEM
Sr.
No.
7.0
8.0
9.0
10.0
11.0
12.0
Description
Unit Qnty
Rate
Supply, installation, testing & commissioning of
Addressable Control Module with surface/ wall mounting Nos
box & required accessories (for Access triping off)
Supply, installation, testing & commissioning of
Addressable Fault / Loop isolator module with Surface
mounting backbox & required accessories.
Supply, installation, testing & commissioning of Response
indicator for Above false ceiling detectors with required
acessories.
Supply, installation, testing & commissioning of
Addressable Relay Module with surface/ wall mounting
box & required accessories.
Supply and laying of 2C x 1.5 Sq.mm Copper Armoured
Multi stranded FRLS cable on wall / slab or structure with
necessary spacer & saddles. scope shall also include
required end termination using gland,lugs & required
accessories. (Red in Colour)
Siren of 3 kms range
BASIC COST
Supply
Duties and Taxes
Total
Rate
Installation
BASIC COST
Taxes
Total
7
Nos
3
Nos
10
Nos
RO
Rmt 500
Nos
1
SUB - TOTAL OF FAS
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot
note
Doc No:
IITM_802_BQ01_00
Page 43 of 60
Rev 00
IITM, Pashan, Pune
Data Centre
BOQ - GAS SUPPRESSION SYSTEM
SCHEDULE OF QUANTITIES FOR NOVEC 1230 FIRE SUPPRESSION SYSTEM FOR SERVER ROOM
Sr.
No.
Description
Unit
Qnty
Rate
Supply,Installation,Testing & Commisioning of :
1
120 ltrs Seamless Cylinder with valve
7
Nos
2
Pressure Guage +Low pressure supervisory switch
7
Nos
3
NOVEC 1230 gas
706
Kgs
4
Electromagnetic Actuator
1
Nos
5
Manual Actuator
1
Nos
6
Pneumatic actuator
7
Nos
7
Flexible Discharge Hose
7
Nos
8
Flexible Actuation Hose
7
Nos
9
Discharge Nozzles
23
Nos.
10
Check Valve
7
Nos.
11
Flow Switch
1
Nos.
12
Manifold
1
Nos.
10
Wall mount kit
14
Nos
11
M.S. Seamless pipes as per ASTM A 106 Gr. B, schedule
40 with necessary fittings.
1
Lot
12
Gas Release panel with release module and battery backup
1
Nos
13
Manual Release Switch
7
No
14
Abort Switch
1
No
15
Room Integrity Test
1
Lot
Supply
BASIC COST Duties and Taxes
Total
Rate
Installation
BASIC COST Taxes
Total
SUBTOTAL
Note : Rates of Duties, taxes in percentagle and nature
of incidential charges for each item may be shown at foot
note
Doc No:
IITM_802_BQ00_00
44
Rev 00
IITM, Pashan, Pune
Data Centre
BOQ - ACCESS CONTROL SYSTEM
Sr.
No.
Description
Unit Qnty
Rate
Supply
BASIC COST Duties and Taxes
Total
Rate
Installation
BASIC COST
Taxes
Total
Access Control System
1
2
3
Supply, installation, testing & commissioning of
Proximity card readers having a read range of
No.
minimum 3 inches with mounting box, plate & required
accessories.
Supply of proximity cards with the possibility of printing
LOT
the company details on its facia using dye sublimation
method.
Supply, installation, testing & commissioning of TCP / IP
based Two Access Door Controllers controlling 4
Readers (2 Entry & 2 Exit ) with minimum 2 Monitor
inputs & 2 Relay outputs, RS232 & RS485 communication
port, complete with Encloser, in-built power supply, & No.
Access Control Software. (controller should have Fire
trigger input facility)
4
Supply, installation, testing & commissioning of TCP / IP
based Four Access Door Controllers controlling 8
Readers (4 Entry & 4 Exit ) with minimum 2 Monitor
inputs & 2 Relay outputs, RS232 & RS485 communication No.
port, complete with Encloser, in-built power supply, &
Access Control Software. (controller should have Fire
trigger input facility)
5
Supply, installation, testing & commissioning of surface
mounted Electro Magnetic door locks having capacity of
holding force of 650 lbs with Armature plate & required
accessories with LED Indications.
6
7
8
9
Supply, installation, testing & commissioning of Magnetic
door Sensor (Door position sensor) with required
accessories.
Supply, installation, testing & commissioning of
Emergency release switch (Break glass type Green in
colour)
Supply and laying of 6C x 1.0 Sq.mm multi stranded,
Shielded Copper FRLS Armoured cable. (For Card
Reader etc.)
Supply and laying of 4C x 1.0 Sq.mm multi stranded,
Shielded Copper FRLS Armoured cable. (For Magnetic
Lock & Door Sensor etc.)
10
25
2
1
No.
10
No.
10
No.
5
Rmt. 250
Rmt. 150
SUB - TOTAL OF ACS
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot
note
Doc. No.
IITM_802_BQ03_00
45
Rev 00
IITM, Pashan, Pune
Data Centre
BoQ - WATER LEAK DETECTION SYSTEM
Sr.
No.
Description
Unit Qnty
Rate
BASIC COST
Supply
Duties and Taxes
Total
Rate
Installation
BASIC COST
Taxes
Total
Water Leak Detection System for Server Room
1
2
3
4
5
6
Supply, installation, testing & commissioning of of 8-32
No.
1
Zone Water Leak Detection Control Panel with power
supply & required accessories.
Supply, installation, testing & commissioning of Water
Rmt. 70
Leak Detection Cable with End Connections
Supply and installation of Fixing clips (At every 0.5 meter
No. Lot
distance)
Supply and installation of Identification tags (At every 1
No. Lot
meter distance)
No. 20
Water Leak Detection Module
Supply, installation, testing & commissioning of Sounder
No.
1
/ Hooter having minimum 85dB.
SUB - TOTAL OF WLDS
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot
note
Doc. No:
IITM_802_BQ04_oo
46
Rev 00
IITM, Pashan, Pune
Data Centre
BOQ - RODENT REPELLENT SYSTEM
Sr.
No.
Description
Unit Qnty
Rate
BASIC COST
Supply
Duties and Taxes
Total
Rate
Installation
BASIC COST
Taxes
Total
Rodent Repllent System for Server Room
1
2
3
Supply, installation, testing & commissioning of Wall
mount type Digital Ultrasonic Rodent Repller Control
Panel having facility to connect upto 20 transducer
satellites including power supply, cabinet & required
accessories. Should have facility of CRMS Software &
Features like Adjustment of Wave Speed, Wave Density,
No.
Frequency Band Time, Frequency & Transducer Testing.
Controller Should be Password Protected.periodic pest
control using
However; Chemical spray can be done once in 3 months
as a contingency measure to effectively fight the pest
menace.
Supply, installation, testing & commissioning of
Transducer Satellite Stations capable of Emitting
Ultrasonic sound of frequencies between 20 Khz and 50
Khz & higher, with blinking LED Indication & mounting No.
accessories. The transducer shall capable for covering
area of minimum 500 sq.ft for ceiling / Floor void & 500
sq.ft. for room void with accessories.
Centralise Reporting & Minitoring Software for Redent
No.
Repellent System
1
30
1
SUB - TOTAL OF RODENT REPELLENT SYSTEM
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot
note
DOc. No:
IITM_802_BQ05_00
47
Rev 00
IITM, Pashan, Pune
Data Center
BOQ - BUILDING MANAGEMENT SYSTEM
Description
Sr. No.
Unit
Qnty
Rate
1
1.1
1.2
1.3
2
2.1
2.2
3
3.1
BASIC COST
Supply
Duties and Taxes
Total
Rate
Installation
BASIC COST
Taxes
Total
BUILDING MANAGEMENT SYSTEM
Supply, installation, testing & commissioning of the
following controls & BMS equipments
BMS Server PC & UPS
Central Server with Quad Core Intel E5620 Processor
2.4GHz or better at 12M Cache, 4 GB or more of RAM, DVD
RW, optical mouse, keyboard & 1 serial port. Server shall
be provided with requisite MS Windows Licensed software
Win ser 2008, compatible with the BMS platform
22" TFT color LCD monitor
A4 size alarm printer suitable for application with driver
software
BMS Client Workstation
Central Work Station Client with Intel processor 2 GHz or
higher, with minimum 250GB HDD, 2 GB RAM, 52X DVD
writer, optical mouse, keyboard & 1 serial port. Work
station shall be preloaded with requisite MS Windows
Licensed software compatible with the BMS platformwith
Database,OS & Firewall softwares.
22" TFT color LCD monitor
Graphical interface software
Providing necessary Software for monitoring through serial
Modbus, BACnet and LONWORKS interface for the data
points for all HVAC/ Electrical/ Other Equipments.
The cost shall include 2 station and 2 client license for the
BMS. The software shall include seamless integration with
FAS / ACS / and CCTV System .
The software shall be open system architecture type which
facilitates interoperability with other systems supporting
BACnet/Modbus protocols. The software shall have
minimum
5000 addresses
with
Future
Expansion
Capability. The software shall have SMS, pging & email
facility for transmitting specified alarms to designated
personnel
Doc. No.
IITM_802_BQ06_00
No.
1
No.
1
No.
1
Nos.
1
Nos.
1
No.
1
60
IITM, Pashan, Pune.
Data Center
BOQ - BUILDING MANAGEMENT SYSTEM
Description
Sr. No.
Unit
Qnty
Rate
4
4.1
4.2
5
6
7
Protocol Convertors / Software Integrators for the
following systems capable of integrating any
Industrially acceptable Communication Protocols
including but not limited to : Modbus RTU / Modbus
ASCII / BACnet / Lonworks / M Bus / J Bus / C Bus;
Made Available either on Serial RS 485 Network or
TCP / IP Network.
(Quantity & protocol mentioned in IO summary)
Energy meter for electrical panels and integration through
Modbus protocol
VFD integration through Modbus/BACnet protocol
System interface unit for connecting database server
to DDC controllers. System interface unit should be of
native BACnet type with built in BACnet router.
External gateway device or proprietary software
driver is not acceptable.
Portable Operator Terminal (POT)
Capable to be hooked to any DDC controller to monitor &
change set points of any parameter
Lot
1
Lot
1
Lot
1
No.
1
Lot
Lot
1
1
No.
No.
No
4
1
1
No
2
Nos.
6
BASIC COST
Supply
Duties and Taxes
Total
Rate
Installation
BASIC COST
Taxes
Total
DDC Controller
32 bit microprocessor based programmable DDC controller,
expansion module compatible to native BACnet protocol.
Controller shall be standalone & networkable type with built
in real time clock. Controller shall support peer to peer
communication. DDC controller shall be housed in IP 55
rated MS powder coated control panel duly internally wired
& tested. Panel should be provided with necessary
accessories, relay boards etc. DDC controller & panel
quantity will be as per the IO summary for following areas
7.1
7.2
8
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
In Substation Room
In BMS Room Ground Floor
Field Devices duly wired to DDC: supply, installation
with all necessary fixtures, site calibration with
documentation, testing and commissioning.
Level Sesors for HSD Tank
Outdoor temp sensor
Out door RH sensor
Diffrential pressure sensor kit with DP sensor for range 13.5 bar. Kit shall generate 4-20mA control signal output.
Combined Room type temp & RH sensor
Supply water temp sensor (PT-100) immersion type with
thermowell
Return air temp sensor
Room type temp & RH transmitter
DPDT relay with 230 VAC, 1A cont rating for fire damper
actuators
Battery fumes detector sensor
Level sensors for thermal storage
Temperature sensor for Thermal storage
Doc. No.
IITM_802_BQ06_00
Nos.
2
Nos.
No.
UR
6
Nos.
4
Nos.
Nos.
Nos.
2
2
2
60
IITM, Pashan, Pune.
Data Center
BOQ - BUILDING MANAGEMENT SYSTEM
Description
Sr. No.
Unit
Qnty
Rate
9
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.10'
10
10.1
10.2
10.3
10.4
10.5
10.6
11
11.1
11.2
2 way valves with actuator
Supply, Installation, Testing and Commisioning of globe
type 2 way chilled water valves with electric actuators for
ON/OFF control for following sizes,
DN 32,
DN 40,
DN 50,
DN 65,
DN 80,
DN 100,
DN 125,
DN 150,
DN 200,
DN 250,
Supply, installation, testing & commissioning
following cables
2 core, screened 1 sq mm ATC cable
4 core, screened 1 sq mm ATC cable
6 core, screened 1 sq mm ATC cable
3 core 1.5 sq mm ATC shielded cable for power
2 core 1 sq mm ATC shielded cable DDC communication
CAT 6 cable for communication between supervisory
controller & BMS server
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
Nos.
UR
UR
UR
UR
1
UR
UR
4
2
UR
Lot
Lot
Lot
Lot
Lot
1
1
1
1
1
Lot
1
Lot
Lot
1
1
BASIC COST
Supply
Duties and Taxes
Total
Rate
Installation
BASIC COST
Taxes
Total
Supply, installation, testing of following PVC conduits
1" dia
1 1/2 " dia
SUB - TOTAL OF BMS
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot
note
Doc. No.
IITM_802_BQ06_00
60
IITM, Pashan, Pune.
BoQ - IP CCTV Surveilliance
Sr.
No.
1
2
3
4
Description
Unit Qnty
Rate
IP CCTV Surveillance System
Supply, installation, testing & commissioning of 1/3"
Progressive Scan CMOS Sensor, 3 MegaPixel Colour Dome
Camera with 2.8 ~ 12.0mm Manual Verifocal Auto iris
Lens, WDNR, Day & Night function with required
accessories. Should be ONVIF Complaint.
Supply, installation, testing & commissioning of 16
Channel Embedded Network Video Recorder, having
features like Third Party Camera Support, HDD
Management & with Redundancy. 8 HDD SATA Capacity.
HDMI & VGA Out Put at up to 1920 X 1080 Pixel
Resolution. Should have up to 5 Megapixel recording
capacity. Should be RAID 0,1,5,10 Supported. Should
have minimum 30 days of recording. The system shall
have auto back up tape slot for data storage
Supply, installation, testing & commissioning of Wall
mount 32" High resolution Flat LCD Monitor with wall
mount accessories.
Supply & installation of 30U wall mount Rack for
mounting the DVR
No.
11
No.
1
No.
1
No.
1
5
Supply, installation, testing & commissioning of DC Power
supply pack with battery backup for all Cameras.
No.
1
6
8 Port POE Network Switch
No.
2
7
Supply and laying of CAT 6 Shilded Cable in PVC Conduit
RMT
130
8
SITC of Video Analytic software
Lot
1
BASIC COST
Supply
Duties and Taxes
Data Centre
Total
Rate
Installation
BASIC COST
Taxes
Total
SUB - TOTAL OF IP CCTV Surveillance System
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot
note
DOc. No:
IITM_802_BQ07_00
51
Rev 00
IITM, Pashan, Pune
BoQ - VESDA
Sr.
No.
1
1.1
2
2.1
Description
Unit
Qnty
Rate
BASIC COST
Supply
Duties and Taxes
Total
Data Centre
Rate
Installation
BASIC COST
Taxes
Total
VESDA SYSTEM
Supply, installation, testing & commissioning of the
following System
Sampling Unit
Supply, Installation, Testing & Commissioning, calculations of
flow and hole sizes in pipe network. Sampling unit shall be
prepared for laser chamber or optical smoke detectors.
Detected smoke density shall be able to be adjusted between
high sensitivity to equal as ordinary smoke detector. Sampling
system is connected to loop for ordinary fire alarm via
address unit.
Operation of sampling unit and status shall be able to display
in fire alarm central unit.
Sampling unit shall have 4 exits for:
1) Pre-alarm 1
2) Pre-alarm 2
3) Fire
4) Fault
25 mm pipe network shall be connected to sampling system,
each unit shall be capable of minimum 1x160 m M-pipe
system. Sampling unit shall have indications for operation,
fault, prealarm1 and pre-alarm 2. Smoke testing shall be
done when commissioning to secure functionality of the
system
Power supply.
240 volts AC power supply with fault alarm connected too fire
alarm system.
No.
20
Rmt.
250
Sampling Pipe
ABS piping should be used due to its strength and heat
resistant properties. The pipe sections should be glued
together using a suitable ABS glue to avoid separation
orleaks. If a section of pipe is likely to need to be
disconnected for some reason in the future, removable unions
should be used instead.
Fixings
The means of fixing the pipe to the structure will depend on
site conditions. The normal methods are pipe clips, saddle
clamps or even tie wraps.
End Cap
The end of the pipe is terminated with an end cap with a hole,
typically 6mm diameter in it. If the end cap is not used, then
practically no air will be drawn through the side holes. If the
end cap does not have a hole then the contributions from the
side holes will tend to be very unbalanced.
Bends
Bends are either 45 or 90 degrees. For the 90-degree bends it
is very important that slow radii are used and not a sharp
elbow, as this will introduce unacceptable pressure losses,
and significantly increase the response times from holes
beyond the bend.
T Pieces
Use of T joints should be avoided as much as possible in these
types of low pressure wide bore systems.
They make the pipe design and air flow calculation very
SUB - TOTAL OF VESDA SYSTEM
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot note
DOc. No:
IITM_802_BQ08_00
52
Rev 00
IITM, Pashan, Pune
BoQ - Dry Powder Type Sprinkler System
Sr.
No.
Description
Unit Qnty
Rate
BASIC COST
Supply
Duties and Taxes
Data Centre
Total
Rate
Installation
BASIC COST
Taxes
Total
Dry Powder Base Sprinkler system
1
Automatic Fire Extinguisher with Clean Agent Type
- The container shall be made with MIG welded MS body.
The upper part shall be with flange.
- The extingisher shall be fixed with sprinkler head which
shall operate at an temperature of 72 Deg C.
- The unit shall be fitted with pressure guage.
- The propellent shall be with Nitrogen
1.1 15 Kg Capacity
No.
47
SUB - TOTAL OF Dry Powder Type Sprinkler System
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot
note
DOc. No:
IITM_802_BQ08_00
53
Rev 00
IITM, Pashan, Pune
IITM DATA CENTER
AEPPL
PROPOSED CONSTRUCTION OF DATA CENTRE FOR IITM , PASHAN.
DISCREPTION
SR.NO
1a
QUANTITY
UNIT
475.00
500.00
70.00
4.00
100.00
SQM
SQM
NOS
NOS
NOS
20.00
20.00
SQM
SQM
FALSE FLOORING …
Providing and Fixing of Unifloor FS1000H access floor system shall
be made from steel cementitious infill and provide for adequate
fire properties, acoustic barrier and air leakage resistance. The
system shall be able to withstand a UDL of 1670kg. Per sqmt. And a
point load of 450 kg. Panels shall be finished with High
Performance Anti Static Laminate.
Panels shall be made from steel. The bottom of the panel shall be
embossed in hemispherical shape to give strength and flexural
rigidity. The top sheet shall be plain and resistant welded at various
locations after the top and bottom sheets have been degreased
and phostated to form a single composit unit. The entire panel
shall be quoted with epoxy coating on the exposed surface and
then the hollow panel shall have an infill of light weight
cementitious material, panel shall remain flat through and stable
unaffected by humidity or fluctuation in temp through out its
normal working life. Panel shall provide for impact resistance top
surfaces minimal deflection, corrosion resistance properties and
shall not be combustible or aid surface spread of flame, panels
shall be insulated against heat and noise transfer. Panels shall
provide qualities of concrete slabs, panels shall be of size
600x600mm and 35mm thick fully interchangeable with each other
within the range of a specified lay out. Panels shall be free standing
onto the structure.
Pedestal - Pedestals installed to support the panel shall be
suitable to achieve a specified floor height from the existing floor
level and shall be placed 600mm distance in both directions to
form a grid of 600x600mm. Pedestal should have GI Base plate of
100 x100 x 2.5mm thk, GI Pipe 22 Dia x 2.2 mm Thk, check nut for
level adjustment, 16 mm dia threaded stud with GI pedestal head
of size 75 x 75 x 3.5 mm thk, stringe, all scews etc and design shall
confirm speedy assembly and removal for relocation and
maintenance. Pedestal assembly shall provide for easy adjustment
of levelling and accurately align panels to ensure lateral restrain.
for prevention of corrosion pedestals are either powder coated or
zinc electroplated as required. Pedestal shall support an axial load
of 2200kg. without permanent deformation and an ultimate load
of 3500kg. The pedestal flat head then shall receive the panel
which shall be fastened by screws to the pedestal head to form a
rigid grid to achieve FFH of 750mm.
Mode of
measurement : Cut tiles less than 300mm shall be considered as
a
b
c
d
e
1b
300mm and more than300mm shall be considered as 600mm.
High Performance Anti Static Laminate Panels
Raised Floor Pedestals includings Stringer for panel support
Perforated Panel 26 % with out damper
Panel Lifter - Heavy Duty
Grommets for cable Access
Item as Above but for
i) For Height of 300 mm
ii) For Height of 450 mm
2
EPOXY FLOORING
Providing and laying 'SIKA' make self leveling type 2 mm thick
epoxy screed flooring of approved color, over 4mm thick base coat
as per manufacturer's instructions including surface preparation,
building up the desired thickness with layers, top coat, cleaning,
testing complete with 5 years guarantee.
250.00
SQM
3
ALUMINIUM CHEQURED PLATE …
250.00
SQM
BOQ - CIVIL WORK
Page 54 of 60
RATE BASIC COST Duties and Taxes
Incidential
Charges
Total
IITM DATA CENTER
AEPPL
DISCREPTION
SR.NO
QUANTITY
UNIT
Providing fabricating and fixing Aluminium Chequred plate 6 mm
thick for platform as per the detailed drawings including
fabrication, fixing and placing in position, leveling etc. complete.
4
NEOPRENE ACOUSTICAL SHEET…
Providing and fixing Neoprene rubber sheets of 5 mm thk for Noise
/ Vibration Control Underlayed aluminium chequered Plate.
Including Fixing and placing in position, leveling etc. complete.
250.00
SQM
5
MODULAR FALSE CEILING…
Providing and fixing false ceiling system manufactured by
Armstrong or Equivalent make using hot dipped galvanized steel
section, rotary stitched main tee of size 15mm x 42 mm web
height, having 0.36 mm gauge at every 600 mm centre to centre
maximum and rotary stitched cross tee of size 15 mm x 42 mm,
having 0.33 mm gauge at every 600 mm. c/c. and wall angle of size
19 x 19 mm., having 0.35 mm gauge fixed to the periphery of the
wall. The above grid is suspended at every 600mm c/c. in both
directions using 2.0 mm. thick pre-straightened GI wire laying FINE
FISSURED MICROLOOK WITH SILHOUETTE GRID(BLACK REVEAL)
ceiling tiles manufactured by Armstrong or Equivalent make of size
600mm x 600mm x 15mm having NRC 0.55, Light reflectance of
>84% (WT), thermal conductivity k = 0.052-0.057 W/m0K,
Humidity Resistance of 99% , having Fire Performance CLASS O /
CLASS 1 (BS 476) - 2 hr, surface having 3 coats of white paint with
Fine Fissured, back of the tile duly sanded and finished with a coat
of protective paint over the formed grid etc. complete
500.00
SQM
6
FIRE RATED PARTITION…
Providing and fixing Min. 2 Hour fire rated 132mm thick Gypsteel
Ultra™ stud partition which includes two layers of tapered edge
15mm thick Gyproc® Fireline boards (conforming to IS:2095 – 1996Part-I) is screw fixed with drywall screws of 25mm & 50mm at
300mm centres to either side of 70mm Gypsteel Ultra™ C stud
(0.5mm thick having one flange of 34mm and another flange of
36mm made of GI Steel) placed at 610mm centre to centre in
72mm Gypsteel Ultra™ floor and ceiling channel (0.5mm thick have
equal flanges of 32mm made of GI steel), which is anchored to the
floor & true ceiling using suitable anchor fasteners. The boards are
to be fixed to the framework with joints staggered to avoid leakage
through joints. A Gypsteel Ultra 70mm Noggin channels has to be
provided at the horizontal joints of the outer layer of boards screw
fixed to the studs using metal to metal flat head screws.
285.00
SQM
Finally square and tapered edges of the boards are to be jointed
and finished so as to have a flush look which includes filling and
finishing with Gyproc Jointing compound, Gyproc Joint Paper tape
and two coats of Drywall Top Coat (as per recommended practices
of Saint- Gobain Gyproc India) . The junction of the partition with
masonry & all penetration through the partition has to be treated
with a intumescent fire sealant of equivalent fire rating.
7
FIRE RATED STEEL DOORS…
BOQ - CIVIL WORK
Page 55 of 60
RATE BASIC COST Duties and Taxes
Incidential
Charges
Total
IITM DATA CENTER
AEPPL
DISCREPTION
SR.NO
QUANTITY
UNIT
a Single Leaf Door - 2 Hr Fire Rated
i) 1200 x 2100 with vision panel
ii) 900 x 2100 without vision panel
1.00
10.00
NOS
NOS
b Doubble Leaf Door - 2 Hr Fire Rated
i) 1800 x 2100 with vision panel
ii) 1800x 2400 without vision panel
4.00
1.00
NOS
NOS
c Doubble Leaf Door - 4 Hr Fire Rated
i) 1800 x 2100 with vision panel
1.00
NOS
Item same As Above but for 2 hr fire rated Sliding door with Vision
panel
i) 1800 x 2100 with vision panel
1.00
NOS
PANIC BARS …
Supplying and fixing Dorma or Equivalent make panic bar with all
fittings etc complete.
i) for Single Leaf Door
i) for Doubble Leaf Door
2.00
2.00
NOS
NOS
1270.00
SQM
200.00
SQM
providing and fixing 2 hr fire rated doubble skin steel door
constructed from 1.25mm thick galvanized steel sheet formed to
provide a 46mm thick fully flush door shell with lock seam joints at
stile edges and the internal construction of the door is a specially
designed Honey Comb structure with reinforcements at top,
bottom and stile surrounds. As per IS 3614 part-1 & part-2 for
stability and integrity and Pressed Galvanized steel confirming to IS
277. Fire door should be tested at CBRI or ARAI for maximum
rating of 2hrs with vision panel. Vision Glass panel should be 6mm
thick clear glass provided in square in standard dimensions of
300mm x 300mm. Door Frame should be produced from 1.6 MM
thick galvanized steel sheet formed to double rebate profile of size
143mm X 57mm (+/- 0.3mm) with a maximum bending radius of
1.4mm and fixed as per manufacturers specification. Including all
approved type( Dorma Make) heavy duty fastenings and fixtures
comprising of :S.S. Ball Bearing Butt hinges 3 mm thk, Mortise Sash
Lock with Lever Handles,D handles, Mortise Dead Bolt, Mortise
Latch, Door Closer, air seal gaskets between shutter and frame, etc
complete.
The door frames and door shutters are primed with ZincPhosphate Stoving Primer and finished with Polyurethane Aliphatic
grade or epoxy paint as per approved manufacturer specifications.
(Supplier -Shakti Met-dor or approved equivalent). (Note - Test
certificates should be available for vision panels as part of the fire
door assembly. Independent glass test certificates will not be
accepted. Manufacturer test certificate shall cover doors both
single and double leaf and all doors supplied should be within the
tested specimen, deviation in specification and sheet thickness
other than what is mentioned in the test certificates are not
allowed. Proper label confirming the type of door and the hourly
rating is mandatory.)
8
9
10
LUSTER...
Providing and applying Luster of approved make and shade on all
surfaces at all heights in three coats including scaffolding,
preparing the surface by brushing and brooming down, applying
primer two coats and final luster paint applying and levelling the
surface with coat of Birla white putty before and after the primer
coat and also after the first coat etc. complete. The dry/wet
cleaning of floors/pipes/glass etc. after painting is to be carried
out, protection of surfaces before painting is included in the item.
11
FIRE PAINT…
BOQ - CIVIL WORK
Page 56 of 60
RATE BASIC COST Duties and Taxes
Incidential
Charges
Total
IITM DATA CENTER
AEPPL
DISCREPTION
SR.NO
QUANTITY
UNIT
5.00
SQM
5.00
SQM
Providing and applying 2 hr fire rated paint of approved make and
shade on all surfaces as per manufacturers specifications at all
heights including scaffolding, preparing the surface by brushing
and brooming down, applying primer coat and top coat, applying
and levelling the surface with coat of Birla white putty before
primer. The dry/wet cleaning of floors/pipes/glass etc. after
painting is to be carried out, protection of surfaces before painting
is included in the item. Flat area in horizontal and vertical plane will
be measured for payment. No additional payment will be made for
grooves, cornices, vatta, moulding etc complete.
12
FIRE EXPANDING FOAM…
Providing and applying fire Expanding Foam having minimum of 2
hours fire rating when tested in accordance with BS 476 part 20
and UL 1479 for horizontal and vertical openings in RCC slabs,
Beams, walls, Brick masonry or Gypsum partitions for passing
service shafts. The service lines could be of various types like
electrical cables, cable trays or metal pipes etc. The foam shall
have Acoustic property as per DIN 4109 and Smoke and Air Seal.
The Foam should have the feature of Repenetrability for future
maintance or repair activities. item includes scaffolding, finishing,
cleaning etc. complete at. all heights, levels & floors. (Make:Hilti CP
620/3M or approved equivalent)
13
FIRE BARRIER MORTAR…
Providing & applying fire Barrier Mortar having minimum of 2
hours fire rating when tested in accordance with BS 476 part 20
and UL 1479 for horizontal and vertical openings in RCC
slabs,beams, walls, Brick masonry or Gypsum partitions for passing
service shafts. The mortar shall have minimum hardened density of
0.8 g/cm3 and compressive strength of 2.9N/Sq mm . The service
lines could be of various types like electrical cable trays , metal
pipes, GI Ducts for AC etc. It should be Smoke & Air Seal. Item
include scaffolding, finishing, cleaning etc. complete at. all heights,
levels & floors. (Make:Hilti CP 636/3M or approved equivalent)
14
WATER SOLUBLE CABLE COATING…
50.00
RMT
5.00
SQM
5.00
SQM
Providing & applying water soluble cable coating applied with
brush or airless spray to prevent the propagation of fires along
internal electrical cables. Should be suitable for protectiing against
spread of flame on timber panels and tested as per IEC 332 part 3
standard for reduced spread of flame & tested as per FM Class
3971. It should have no derating effect on cables, free from
fibre,asbestos, odourless and solvent free, flexible when dry after
application. Item include scaffolding, finishing, cleaning etc.
complete at. all heights, levels & floors. (Make:Hilti /3M or
approved equivalent)
15
FIRE RESISTANT BOARD SYSTEM…
Providing & fixing fire resistant board system having minimum of 2
hours fire rating when tested in accordance with BS 476 part 20 for
horizontal and vertical openings in RCC slabs,beams, walls, Brick
masonry or Gypsum partitions for passing service shafts. The fire
resistant board system shall comprise of a mineral wool board
having a minimum density of 160kg/m3 coated with an ablative
coating at 0.7mm dft. All contact surfaces and cavities shall be
sealed with an firestop filler. The service lines could be of various
types like electrical cables trays, metal pipes, etc.The Mineral Wool
Board should also have the Acoustic property ,Air and Smoke seal.
Item include scaffolding, finishing, cleaning etc. complete at. all
heights, levels & floors. (Make:Hilti CP 678/3M or approved
equivalent)
16
GRAPHITE BASED INTUMESCENT FIRESTOP SEALANT…
BOQ - CIVIL WORK
Page 57 of 60
RATE BASIC COST Duties and Taxes
Incidential
Charges
Total
IITM DATA CENTER
AEPPL
DISCREPTION
SR.NO
QUANTITY
UNIT
1500.00
3000.00
2000.00
4000.00
4000.00
4000.00
mm
mm
mm
mm
mm
mm
Providing & applying graphite based intumescent firestop sealant
having minimum of 2 hours fire rating when tested in accordance
with BS 476 part 20 suitale for annular space for combustible pipes
and cables.It should expand in fire , protecting pipe and cable
penetration and must be halogen, solvent free and odourless.
Firestop sealent should have property of Accoustic, Smoke and Air
sealing. Item include scaffolding, finishing, cleaning etc. complete
at. all heights, levels & floors. (Make:Hilti CP 611 A/3M or
approved equivalent)
17
MAKING THROUGH HOLES...
Making through holes in plain or reinforced cement concrete with
Diamond core drilling system by using Bosch power tools.of
following diameters. Rate in Dia/mm
a) 52 mm dia
b) 82 mm dia
c) 112 mm dia
d) 122 mm dia
e) 152 mm dia
f) 202 mm dia
18
SOFT BOARD WITH FIRE RATED FABRIC…
Providing and Fixing approved shade and make FR grade PolyesterCotton fabric over 12mm thick softborad of required size, on
partition/wall etc. The fabric shall be certified to pass Surface
Abrasion test of no yarn breakage after abrasion test across 10000
cycles; Fire Retardant finish as per BS EN 1021-1:1994, BS
7176:1995 low hazard section, IS 15061-2002 Clause 3.3 annex. B
(Vertical test) and water repellent as per standard AATCC-118.
Item to include all accessories, tools & labour, getting mock-up for
approved by Architect/Engineer in charge; with Protecting with
min. 20 micron polythene sheet cover till handover of facility, item
complete with tight wrinkle free wrapping around soft board or
approved boarding substrate, finished cleaned complete. The
board shall be fixed on prepared surface with necessary hardware
fittings etc. complete. Rate quoted shall be for the complete
finished work including all the materials and labour mentioned
above. Item to be completed in all respects as per instructions
from Project- in-charge.
5.00
SQM
19
White board-Portable
Providing and placing on location Portable framed Magnetic Glossy
finish type White board avg. 900 x 1200 size, as per approved
model and make, with particle board backer and encasing. Item to
include all fixing accessories, a marker/duster tray, including
keeping in packaged condition till handover, cleaned complete. The
item shall be supplied with necessary accessories such as magnetic
symbols, magnetic letters, magnetic strips, magnetic eraser,
magnetic dry marker 4 Nos., spare felt for eraser, board fixing clips
etc. complete and all as per manufacturer's specification and as
directed by the EIC / Architect.
5.00
SQM
20
EXECUTIVE TABLES
1.00
NO
3.00
NO
Providing & fixing in position Executive tables with 18 mm MDF
with drawers & storages, should have 1 mm thick Laminte of
approved quality and shade of Laminate for all exposed surface
.All unlaminated faces should have a melamine polish of matching
shade of Laminate. Polish and chamfered for edge. The cost
includes all necessary hardware like brass hinges/ locks, drawer
channel, provision of cable manager, preparation of mockup etc
complete. ( For keeping keyboard special fixtures like INNOFITT or
Equivelent to be provided )
a
TRAVEL DESK (1350L x 750W x 750H)
21
LOW BACK CHAIRS
BOQ - CIVIL WORK
Page 58 of 60
RATE BASIC COST Duties and Taxes
Incidential
Charges
Total
IITM DATA CENTER
AEPPL
DISCREPTION
SR.NO
QUANTITY
UNIT
Providing and supplying in position revolving chairs having 5 prong
FR nylon in black finish or 5 prong aluminium in chrome finish with
castors. The seat should be having gas lift adjustment with gas
stroke. The mechanism for the chair should be synchronized tilt
mechanism with multiple locking position. The seat and back of the
chair should be made up of injection moulding PU foam with
12mm thick double ply backing. The seat and back should have
fabric upholstry in specified colour and texture. The chair should
have adjustable seat depth. The back rest should be made up of
poly propylene with height adjustment. The arm rest should have
height adjustment and to be made up of injection moulded PU
foam and should be supported on a polypropylene hand rest
assembled to the main body of the chair which is made up of
polypropylene with fabric/rexine upholstry of approved color &
texture. The colour of the fabric/rexine should be as specified by
Architect. The chair should confirm the ANSI/BIFMA X5.1 standard.
The cost of the chair includes preparation of mock up etc.
complete. (The density of the foam should be 45 Kg/m3)
22
Room Signages/ Manager Cabins/ Utility Rooms(150x300)
Providing & fixing Aluminium Modular Signage using Aluminium
Alloy 6063 extrusion with Anodising (The thickness of the
anodization is typically 30 microns. The integrity of the anodize
coating is tested to meet the international specifications ISO 21431981.) With lifetime Warranty in normal working condition.
Clear Cover : Clear UV protected 1mm thick Poly carbonate Sheet
with Non Glare/Glossy Finish.
Plastic End Cap : High Quality ABS End Caps with Screws which can
be fastened into the extrusion.
Graphics : Photo paper Insert
10.00
NOS
23
Way Finding Sign/Department Identification (150x600)
Providing & fixing Aluminium Modular Signage using Aluminium
Alloy 6063 extrusion with Anodising (The thickness of the
anodization is typically 30 microns. The integrity of the anodize
coating is tested to meet the international specifications ISO 21431981.) With lifetime Warranty in normal working condition.
Clear Cover : Clear UV protected 1mm thick Poly carbonate Sheet
with Non Glare/Glossy Finish.
Plastic End Cap : High Quality ABS End Caps with Screws which can
be fastened into the extrusion.
Graphics : Photo paper Insert
10.00
NOS
24
Fire Evacuation Map (400x300)
Providing 7 fixing Aluminium Modular Signage , fire evacuation
map using Aluminium Alloy 6063 extrusion with Anodising (The
thickness of the anodization is typically 30 microns. The integrity of
the anodize coating is tested to meet the international
specifications ISO 2143-1981.) With lifetime Warranty in normal
working condition.
Clear Cover : Clear UV protected 1mm thick Poly carbonate Sheet
with Non Glare/Glossy Finish.
Plastic End Cap : High Quality ABS End Caps with Screws which can
be fastened into the extrusion.
Graphics : Night Glow Vinyl with clear film Printing
2.00
NOS
25
Structural steelwork in hot rolled tubular sections...
Providing fabricating & erecting structural steelwork in hot rolled
tubular Sections for trusses, purlins etc. with all bracings, gusset
plates etc. as per detailed drawing or as directed at all heights and
levels including removing the scales & burrs, cleaning with
phosphoric acid ,marking, Cutting, fabrication, hoisting, erecting &
fixing in position, making alignment of members making welded /
bolted / riveted connections with one coat of approved red-oxide
paint etc complete
4.50
MT
BOQ - CIVIL WORK
Page 59 of 60
RATE BASIC COST Duties and Taxes
Incidential
Charges
Total
IITM DATA CENTER
AEPPL
DISCREPTION
SR.NO
QUANTITY
1.50
26
Structural steelwork in hot rolled sections...
Providing fabricating & erecting structural steelwork in hot rolled
sections ( ISMB, ISMC, ISA) For columns, tie beams, trusses, purlins,
gantry, monorail columns, plates, cable trays, pipe racks,
castellated beams, staircase & other structural members with all
bracings,gusset plates etc.as per detailed drawing or as directed at
all heights and levels including removing the scales & burrs,
cleaning with Phosphoric acid, marking, cutting, fabrication,
hoisting, erecting & fixing in position, making alignment of
members making welded / bolted / riveted Connections and
finishing with two coats of synthetic enamel paint of approved
quality and colour over one coat of approved red-oxide paint etc
complete. Yield Stress FY = 250Mpa as per IS 2062
UNIT
MT
27
Auto Clave Masonry (Light weight blocks Masonry)
Providing and constructing 200 mm thick Auto clave block masonry
at all elevations and heights in cement mortar 1:4 using (150 x 300
x 600 )size with required size block bats , including all scaffolding,
staging, racking the joints, curing etc., at all heights, elevations
above and below finished floor level etc., all complete shall be as
per specification and laid as directed.
40.00
SQM
28
Internal cement plaster (neeru finish)...
80.00
SQM
Providing and applying Plastering of internal walls and ceiling with
cement mortar 1:4, 12 - 15 mm thick with neeru finish according to
specifications. Rate includes providing & fixing in position
expanded metal plaster mesh [ Arpitha make ] or equivalent
minimum 6" wide strips at the junctions of R.C.C columns/
beams/slab with brick work or wherever necessary, properly fixed,
abutting the wall surfaces so as to get the plaster in line and
plumb, necessary staging,scafolding and curing at all levels and
elevations etc.complete as directed.
29
Granite stone, skirting, treads, risers...
Providing and laying high polished approved quality and shade 20
mm thick Granite stone for treads, risers and skirting in line and
level on a bed of 1:4 cement plaster including cement float, filling
joints with matching color Cement slurry, curing, edge high
polishing, chamfering, cleaning, etc. complete. ( Basic Rate - 150
Sqft)
8.00
SQM
30
Fire Rated Vision Glass Window…
Min. 2 hr Fire Rated Vision Glass Window with all Framing &
Fixtures ( Note - Fire Rating should be for Hole Assembly ie Glass +
framing )
10.00
SQM
TOTAL
Note : Rates of Duties, taxes in percentagle and nature of
incidential charges for each item may be shown at foot note
BOQ - CIVIL WORK
Page 60 of 60
RATE BASIC COST Duties and Taxes
Incidential
Charges
Total
Download PDF
Similar pages