WATER
GAS
ENVIRONMENT
PEST
CONTROL
HAND WASH STATIONS
NEW
The new BaSix range is the next
generation of hand wash stations,
designed to promote optimal
hygiene practise with minimal fuss.
BENEFITS
Mechline’s new BaSix range is manufactured using
a unique combination of high grade polished 304
Austenitic stainless steel for the bowl and deck,
and a high grade, high strength injection moulded
ABS-Polycarbonate for the skirt.
The combination provides a robust, easy to clean
and easy to install basin which has been
specifically designed to be ideal for commercial
kitchen installations.
- across the whole range.
The law governing food
preparation areas requires that
separate wash hand basins must
be provided in any food area,
which must only be used for
washing hands and be easy to
get at and use.
The basin must provide hot and cold running water (or
a single feed at a suitable temperature) and suitable
drainage. It is commonly recommended that hand washing
should take at least 20 seconds of continuous lathering
using soap and running water.
For this reason Mechline supplies wash hand basins as
standard without plugs to prevent the accumulation of
water and other materials in the basin.
This policy also helps satisfy the requirement that facilities
for washing food and utensils are to be separate from
hand washing facilities and that food preparation tasks are
conducted in appropriate purpose supplied sinks and not
in hand wash basins.
Call us on: +44 (0) 1908 261511 | Send enquiries to: info@mechline.com | Email orders to: orders@mechline.com | www.mechline.com
47
WATER
GAS
ENVIRONMENT
PEST
CONTROL
HAND WASH STATIONS
Mounting bracket
supplied with every
model for fast and
easy installation
Push-Front panel
with all KVS models
400i basin with
integral splashback
Supplied complete with drain boss
and mixing valve, if applicable
Basins supplied with a choice
of tap including the electronic
Delabie Tempomatic 3 tap
Hand Wash Stations - BaSix
Tap hole stopper included
48
No facia mounting screws,
which can attract dirt
Integral flush
grated waste
reduces the
risk of bacterial
development
NB: Product accreditation may not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship
on parts.
No inclusion is made for labour or site attendance. Dimensions shown in mm unless otherwise stated. Information and numerical data has been prepared as a general guide to the products but intending buyers & users must satisfy themselves as
to the suitability and safety of the products for their particular purposes & duties. The WRAS Approved Product logo is a certification mark which is owned by WRAS Ltd.
WATER
GAS
ENVIRONMENT
PEST
CONTROL
HAND WASH STATIONS
•
- across the whole range
• Curved design, ideal for commercial kitchens
• No sharp corners for kitchen staff to knock into
• Easy to clean integral flush grated waste
reduces the risk of bacterial development
• Bowl and deck are permanently bonded to the skirt,
removing the need for exposed bolts or rivets
• High strength injection moulded skirt removes
the possibility of cut hazards created by sharp
stainless steel edge
• Soft-touch, front panel operated basins are part of the range
• Mounting bracket with integral spirit level for
fast and easy installation
High grade polished
304 austenitic
stainless steel for
the bowl and deck,
and a high grade,
high strength
injection moulded
ABS-Polycarbonate
for the skirt
• Optional waste bins can be fitted to all models
• Stylish, functional design
Fixed chrome-plated brass
spout comes as standard
on our hands-free
front panel operated basins
Our hands-free ‘Push-Front’
panel operated basins
feature soft-touch technology,
allowing users to operate the
basin with no effort
Hand Wash Stations - BaSix
Optional stainless steel
splashback available
for 300 basin range
• Basins supplied pre-fitted with hardware of
your choice for fast and easy installation
49
WATER
GAS
ENVIRONMENT
PEST
CONTROL
HAND WASH STATIONS
BUILD YOUR PERFECT HAND WASH STATION
IN 2 EASY STEPS
1
CHOOSE YOUR BASIN
BSX-300
BSX-400i
Same as the BSX-400 but with an integral splashback
O/D: 300 x 320 x 160mm
Bowl: 260mm dia. x 130mm deep
Optional splashback, soap dispenser
and waste bin are also available.
Supplied with a push-front panel
if you choose the ‘hands-free’
operated spout
option (KVS)
BSX-400
O/D: 400 x 360 x 160mm
Bowl: 358 x 310 x 160mm deep
Optional soap dispenser and
waste bin are also available.
Supplied with a push-front panel
if you choose the ‘hands-free’
operated spout
option (KVS)
2
CHOOSE YOUR TAP
Hand Wash Stations - BaSix
SAVE WATER & IMPROVE HYGIENE
WITH INTELLIGENT DESIGN
50
Pair of WRAS
3" LEVER taps
Pair of WRAS
LEVER taps
TX-BL
Pair of WRAS
DOME taps
TX-BD
CT-L
Pair of WRAS
DOME taps
CT-D
Single WRAS
3" LEVER tap
with manual mixer
ML
ML is only an
option with the
BSX-300.
HANDS-FREE
WRAS push-front
panel operated
fixed spout
with manual mixer
HANDS-FREE
Tempomatic 3
battery-operated
WRAS tap
with manual mixer
Soft-touch
operated,
time flow
WRAS tap
with manual mixer
KVS
NT
T2
As above with
thermostatic mixer
As above with
thermostatic mixer
As above with
thermostatic mixer
KVS-T
NT-T
T2-T
NB: Product accreditation may not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship on parts.
No inclusion is made for labour or site attendance. Dimensions shown in mm unless otherwise stated. Information and numerical data has been prepared as a general guide to the products but intending buyers & users must satisfy themselves as
to the suitability and safety of the products for their particular purposes & duties. The WRAS Approved Product logo is a certification mark which is owned by WRAS Ltd.
WATER
GAS
ENVIRONMENT
PEST
CONTROL
HAND WASH STATIONS
300 MODELS
Basin dia.: O/D: 300 x 320 x 160 Bowl: 260 dia. x 130 deep
With your choice of tap, or there’s an easy push-front panel basin for the “hands-free” operated spout option (KVS).
with fixed spout
and push-front panel
with CaterTap
lever taps
BSX-300-KVS
BSX-300-CT-L
with CaterTap
dome taps
BSX-300-CT-D
Complete with basin, drain boss and your choice of tap or push-front panel operated spout (with mixing valve)
Model
Description
FURTHER OPTIONS
BSX-300-TX-BL
with a pair of AquaTechnix LEVER taps Model
Description
BSX-300-TX-BD
with a pair of AquaTechnix DOME taps BSX300-SPL
Optional Splashback
BSX-300-CT-L
with a pair of CaterTap 3" LEVER taps BSX-300-CT-D
with a pair of CaterTap 3” DOME taps BSX-300-ML
with single 3” LEVER tap and manual mixer for 300 models only,
315(H) x 300(W)
Water Savings and Hygiene Options
‘Push-Front’, Hands-Free mechanical operation BSX-SPD
BSX-300-KVS-T
‘Push-Front’, Hands-Free mechanical operation Includes fixed spout, Premix Nano DLB-732-115
thermostatic mixer, water hose & tap hole stopper
BSX-300-NT
Optional Soap Dispenser
See page 100 for more details
Includes fixed spout, M-MX91 manual mixer,
water hose & tap hole stopper
Battery-Operated, Hands-Free operation BSX-WASTE-BIN
Optional Waste Bin
Hangs neatly under the basin
Includes Delabie Tempomatic 3 tap, M-MX91
manual mixer, water hose & tap hole stopper
BSX-300-NT-T
Battery-Operated, Hands-Free operation Includes Delabie Tempomatic 3 tap, Premix Nano
DLB-732-115 thermostatic mixer, water hose
& tap hole stopper
BSX-300-T2
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap, M-MX91
manual mixer, water hose & tap hole stopper
BSX-300-T2-T
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap, Premix Nano
DLB-732-115 thermostatic mixer, water hose
& tap hole stopper
Call us on: +44 (0) 1908 261511 | Send enquiries to: info@mechline.com | Email orders to: orders@mechline.com | www.mechline.com
Hand Wash Stations - BaSix
BSX-300-KVS
51
WATER
GAS
ENVIRONMENT
PEST
CONTROL
HAND WASH STATIONS
400 MODELS
Basin dia.: O/D: 400 x 360 x 160 Bowl: 358 x 310 x 160 deep
With your choice of tap, or there’s an easy push-front panel basin for the “hands-free” operated spout option (KVS).
with battery-operated,
hands-free operation
with AquaTechnix
dome taps
BSX-400-NT
BSX-400-TX-BD
with CaterTap
lever taps
BSX-400-CT-L
Complete with basin, drain boss and your choice of tap or push-front panel operated spout (with mixing valve)
Model
Description
BSX-400-TX-BL
with a pair of AquaTechnix LEVER taps BSX-400-TX-BD
with a pair of AquaTechnix DOME taps BSX-400-CT-L
with a pair of CaterTap 3" LEVER taps BSX-400-CT-D
with a pair of CaterTap 3” DOME taps FURTHER OPTIONS
Model
Description
BSX-SPD
Optional Soap Dispenser
See page 100 for more details
Water Savings and Hygiene Options
BSX-400-KVS
‘Push-Front’, Hands-Free mechanical operation Includes fixed spout, M-MX91 manual mixer,
water hose & tap hole stopper
BSX-400-KVS-T
BSX-WASTE-BIN
Optional Waste Bin
Hangs neatly under the basin
‘Push-Front’, Hands-Free mechanical operation Includes fixed spout, Premix Nano DLB-732-115
thermostatic mixer, water hose & tap hole stopper
BSX-400-NT
Battery-Operated, Hands-Free operation Hand Wash Stations - BaSix
Includes Delabie Tempomatic 3 tap, M-MX91
manual mixer, water hose & tap hole stopper
52
BSX-400-NT-T
Battery-Operated, Hands-Free operation Includes Delabie Tempomatic 3 tap, Premix Nano
DLB-732-115 thermostatic mixer, water hose
& tap hole stopper
BSX-400-T2
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap, M-MX91
manual mixer, water hose & tap hole stopper
BSX-400-T2-T
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap, Premix Nano
DLB-732-115 thermostatic mixer, water hose
& tap hole stopper
NB: Product accreditation may not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship on parts.
No inclusion is made for labour or site attendance. Dimensions shown in mm unless otherwise stated. Information and numerical data has been prepared as a general guide to the products but intending buyers & users must satisfy themselves as
to the suitability and safety of the products for their particular purposes & duties. The WRAS Approved Product logo is a certification mark which is owned by WRAS Ltd.
WATER
GAS
ENVIRONMENT
PEST
CONTROL
HAND WASH STATIONS
400i MODELS
Basin dia.: O/D: 400 x 360 x 510 Bowl: 358 x 310 x 160
With your choice of tap, or there’s an easy push-front panel basin for the “hands-free” operated spout option (KVS).
with CaterTap
dome taps
BSX-400i-CT-D
with soft-touch operated, time flow tap
BSX-400i-T2
with AquaTechnix
lever taps
BSX-400i-TX-BL
Complete with basin, drain boss and your choice of tap or push-front panel operated spout (with mixing valve)
Model
Description
FURTHER OPTIONS
BSX-400i-TX-BL
with a pair of AquaTechnix LEVER taps Model
Description
BSX-400i-TX-BD
with a pair of AquaTechnix DOME taps BSX-SPD
Optional Soap Dispenser
BSX-400i-CT-L
with a pair of CaterTap 3" LEVER taps BSX-400i-CT-D
with a pair of CaterTap 3” DOME taps See page 100 for more details
Water Savings and Hygiene Options
BSX-400i-KVS
‘Push-Front’, Hands-Free mechanical operation Includes fixed spout, M-MX91 manual mixer,
water hose & tap hole stopper
BSX-400i-KVS-T
BSX-WASTE-BIN
Optional Waste Bin
Hangs neatly under the basin
‘Push-Front’, Hands-Free mechanical operation Includes fixed spout, Premix Nano DLB-732-115
thermostatic mixer, water hose & tap hole stopper
Battery-Operated, Hands-Free operation Includes Delabie Tempomatic 3 tap, M-MX91
manual mixer, water hose & tap hole stopper
BSX-400i-NT-T
Battery-Operated, Hands-Free operation Includes Delabie Tempomatic 3 tap, Premix Nano
DLB-732-115 thermostatic mixer, water hose
& tap hole stopper
BSX-400i-T2
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap, M-MX91
manual mixer, water hose & tap hole stopper
BSX-400-T2-T
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap, Premix Nano
DLB-732-115 thermostatic mixer, water hose
& tap hole stopper
Call us on: +44 (0) 1908 261511 | Send enquiries to: info@mechline.com | Email orders to: orders@mechline.com | www.mechline.com
Hand Wash Stations - BaSix
BSX-400i-NT
53
WATER
GAS
ENVIRONMENT
PEST
CONTROL
HAND WASH STATIONS
The BaSix range offers a
range of hygienic hand
washing solutions including
Janitorial & Mop Sinks
SAVE WATER
AND
IMPROVE HYGIENE
WITH INTELLIGENT
DESIGN
BENEFITS
Mechline’s BaSix range of hygienic hand-washing
solutions help operations meet their requirement to
provide hand-washing stations for staff on site. By giving
the tools to make it easier and faster, good and safe
habits are more easily followed and enforced.
Hands-free use significantly reduces crosscontamination and risk from germs and bacteria to
improve health and safety.
54
Water Savings
Improve Hygiene
Utility Sinks
With Delabie electronic hands-free taps
you could enjoy up to 90% water savings!
- approx. £1300 pa. based on standard
foodservice operations.
Hand-washing is the number one prevention
against the spread of bacteria and
pathogens. Good hand-washing habits can
be encouraged with the right equipment.
Robust stainless steel construction utility
sinks featuring lift out (removable) mop
strainer.
NB: Product accreditation may not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship on parts.
No inclusion is made for labour or site attendance. Dimensions shown in mm unless otherwise stated. Information and numerical data has been prepared as a general guide to the products but intending buyers & users must satisfy themselves as
to the suitability and safety of the products for their particular purposes & duties. The WRAS Approved Product logo is a certification mark which is owned by WRAS Ltd.
WATER
GAS
PEST
CONTROL
ENVIRONMENT
HAND WASH STATIONS
BUILD YOUR PERFECT HAND WASH STATION
IN 3 EASY STEPS
1
CHOOSE YOUR BASIN
WS3
WS1
Stainless steel (304) basin.
Push-front panel style when fitted
with hands-free KVS
GREY ABS Polycarbonate basin
O/D: 355 x 320 x 195mm
Bowl: 255 x 278 x 110mm deep
O/D: 300 x 320 x 195mm
Bowl: 260mm dia. x 150mm deep
Optional splashback and soap
dispenser also available.
Optional splashback and soap
dispenser also available.
WS4
Stainless steel (304) basin
WS1
O/D: 384 x 333 x 138mm
Bowl: 300mm dia. x 138mm deep
As above in WHITE
Please also complete step 3
if the WHITE WS1 is your
preferred basin.
Optional soap dispenser
also available.
WS6
Stainless steel (304) push-front panel
style basin with integral splashback
WS2
Stainless steel (304) basin
O/D: 420 x 375 x 570mm
Bowl: 360 x 270 x 100mm deep
O/D: 305 x 270 x 140mm
Bowl: 240 x 110 x 135mm deep
Optional soap dispenser and waste bin
also available.
Optional soap dispenser
also available.
2
CHOOSE YOUR TAP
Pair of WRAS
LEVER taps
TX-BL
Pair of WRAS
DOME taps
TX-BD
All above not an
option with WS6.
Pair of WRAS
3" LEVER taps
Pair of WRAS
DOME taps
L
D
Single WRAS 3" LEVER tap
with manual mixer
ML
Single 3" LEVER tap
with thermostatic mixer
ML-T
All above not an option with WS6.
Monobloc, single
LEVER mixer tap
MM
Not with WS6.
HANDS-FREE
knee-valve
operated spout
for WS1, WS2
or WS4 and
push-front panel
operated spout
for WS3 or WS6
with manual mixer
HANDS-FREE
Soft-touch time
‘Auto shut-off’
TEMPOMATIC 3
flow WRAS tap single LEVER tap
battery-operated with manual mixer with manual mixer
WRAS tap
T2
MT
with manual mixer
T2-T
MT-T
KVS
All above not an
option with WS6.
All above not an
option with WS6.
NT
Not an option
with WS2.
with
with
thermostatic mixer thermostatic mixer
Call us on: +44 (0) 1908 261511 | Send enquiries to: info@mechline.com | Email orders to: orders@mechline.com | www.mechline.com
Hand Wash Stations - BaSix
SAVE WATER & IMPROVE HYGIENE
WITH INTELLIGENT DESIGN
55
WATER
GAS
ENVIRONMENT
PEST
CONTROL
HAND WASH STATIONS
HAVE YOU CHOSEN A WHITE WS1?
3
This STEP is only applicable if you prefer the WHITE WS1 basin in STEP 1
Please add
WHITE
(Grey WS1 basins are standard).
to the end of your order code.
ORDER CODE EXAMPLES
Basin
Tap
WS3
KVS
WS1
T2
Codes would be written as:
White WS1?
WHITE
=
WS3-KVS
=
WS1-T2-WHITE
WS1 MODELS
ABS Polycarbonate basin dia.: O/D: 355 x 320 x 195 Bowl: 255 x 278 x 110 deep
Engineered from a single-piece, moulded high-grade polycarbonate ABS plastic, the WS1 is ergonomic, attractive, strong & durable with no
sharp edges. SaniTru® antimicrobial additive embedded in the basin material resists mould, mildew & grime to provide
a cleaner surface. Eco-friendly, the WS1 can be fully recycled & has lower embedded energy costs than traditional
stainless steel basins. Designed & manufactured in the UK by Mechline.
Grey basins
are standard.
Please clearly
indicate “WHITE”
after model ref.
if preferred.
WS1-L
WS1-KVS-WHITE
pictured with SPL-WS1
Hand Wash Stations - BaSix
Complete with basin, drain boss, choice of tap or hands-free control (with mixing valve).
Model
Description
Model
Description
WS1-TX-BL
with a pair of AquaTechnix LEVER taps WS1-T2
Soft-touch operated, time flow tap
WS1-TX-BD
with a pair of AquaTechnix DOME taps WS1-L
with a pair of CaterTap 3" LEVER taps WS1-D
with a pair of CaterTap 3” DOME taps WS1-ML
with single 3" LEVER tap and manual mixer WS1-ML-T
with single 3" LEVER tap and thermostatic mixer
WS1-MM
with Monobloc, single LEVER mixer tap
Water Savings and Hygiene Options
WS1-KVS
Knee-Operated, Hands-Free mechanical operation
Includes knee-valve, fixed spout, M-MX91 manual mixer,
water hose & tap hole stopper
WS1-NT
WS1-T2-T
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap, Premix Nano
DLB-732-115 thermostatic mixer, water hose & tap hole stopper
WS1-MT
with ‘auto shut-off’ single LEVER tap
and manual mixer
WS1-MT-T
with ‘auto shut-off’ single LEVER tap
and thermostatic mixer
Further Options
SPL-WS1
Optional Splashback for WS1 models only,
245(H) x 342(W)
BSX-SPD
Optional Soap Dispenser - See page 100 for more details
Battery-Operated, Hands-Free operation Includes Delabie Tempomatic 3 tap,
M-MX91 manual mixer, water hose & tap hole stopper
56
Includes Delabie Temposoft 2 tap,
M-MX91 manual mixer, water hose & tap hole stopper
NB: Product accreditation may not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship on parts.
No inclusion is made for labour or site attendance. Dimensions shown in mm unless otherwise stated. Information and numerical data has been prepared as a general guide to the products but intending buyers & users must satisfy themselves as
to the suitability and safety of the products for their particular purposes & duties. The WRAS Approved Product logo is a certification mark which is owned by WRAS Ltd.
WATER
GAS
ENVIRONMENT
PEST
CONTROL
HAND WASH STATIONS
WS2 MODELS
WS3 MODELS
Stainless steel (304) basin dia.: O/D: 305 x 270 x 140
Stainless steel (304) basin dia.: O/D: 300 x 320 x 195
Bowl: 240 x 110 x 135 deep
Bowl: 260 dia. x 150 deep
Choose your tap, or “hands-free” knee-valve operated spout (KVS)
to create your perfect hand wash station.
Choose your tap, or there’s an easy push-front panel for the
“hands-free” operated spout option (KVS).
WS3-KVS
WS2-T2
WS2-KVS
WS3-NT
pictured with SPL-WS3
Complete with basin, drain boss,
choice of tap or hands-free control
(with mixing valve)
Description
WS3-TX-BL
with a pair of AquaTechnix LEVER taps WS3-TX-BD
with a pair of AquaTechnix DOME taps WS3-L
with a pair of CaterTap 3" LEVER taps Model
Description
WS3-D
with a pair of CaterTap 3” DOME taps WS2-TX-BL
with a pair of AquaTechnix LEVER taps WS3-ML
with single 3” LEVER tap and manual mixer WS2-TX-BD
with a pair of AquaTechnix DOME taps WS3-ML-T
with single 3” LEVER tap and thermostatic mixer
WS2-L
with a pair of CaterTap 3" LEVER taps WS3-MM
with Monobloc, single LEVER mixer tap
WS2-D
with a pair of CaterTap 3” DOME taps Water Savings and Hygiene Options
WS2-ML
with single 3" LEVER tap and manual mixer WS3-KVS
WS2-ML-T
with single 3” LEVER tap and thermostatic mixer
WS2-MM
with Monobloc, single LEVER mixer tap
Includes fixed spout, M-MX91 manual mixer,
water hose & tap hole stopper
WS3-NT
Knee-Operated, Hands-Free mechanical operation
Includes knee-valve, fixed spout, M-MX91 manual mixer,
water hose & tap hole stopper
WS2-T2
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap,
M-MX91 manual mixer, water hose & tap hole stopper
WS2-T2-T
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap, Premix Nano
DLB-732-115 thermostatic mixer, water hose & tap hole stopper
WS2-MT
with ‘auto shut-off’ single LEVER tap and manual mixer
WS2-MT-T
with ‘auto shut-off’ single LEVER tap and thermostatic mixer
WS3-T2
Optional Soap Dispenser See page 100 for more details
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap,
M-MX91 manual mixer, water hose & tap hole stopper
WS3-T2-T
Soft-touch operated, time flow tap
Includes Delabie Temposoft 2 tap, Premix Nano
DLB-732-115 thermostatic mixer, water hose & tap hole stopper
WS3-MT
with ‘auto shut-off’ single LEVER tap and manual mixer
WS3-MT-T
with ‘auto shut-off’ single LEVER tap and thermostatic mixer
Further Options
SPL-WS3
Optional Splashback for WS3 models only,
315(H) x 300(W)
BSX-SPD
Optional Soap Dispenser See page 100 for more details
Further Options
BSX-SPD
Battery-Operated, Hands-Free operation Includes Delabie Tempomatic 3 tap,
M-MX91 manual mixer, water hose & tap hole stopper
Water Savings and Hygiene Options
WS2-KVS
‘Push-Front’, Hands-Free mechanical operation
Call us on: +44 (0) 1908 261511 | Send enquiries to: info@mechline.com | Email orders to: orders@mechline.com | www.mechline.com
Hand Wash Stations - BaSix
Complete with basin, drain boss, choice of tap or hands-free control
(with mixing valve)
Model
57
WATER
GAS
PEST
CONTROL
ENVIRONMENT
HAND WASH STATIONS
WS4 MODELS
WS6 MODELS
Stainless steel (304) basin dia.: O/D: 384 x 333 x 138
Stainless steel (304) basin dia.: O/D: 420 x 375 x 570
Bowl: 300 dia. x 138 deep
Bowl: 360 x 270 x 100 deep
Choose your tap, or “hands-free” knee-valve operated spout (KVS)
to create your perfect hand wash station.
Choose your tap, or there’s an easy push-front panel for the
“hands-free” operated spout option (KVS).
WS4-KVS
WS6-KVS
WS6-NT
WS4-NT
Complete with basin, drain boss,
choice of tap or hands-free control
(with mixing valve)
Model
Description
WS4-TX-BL
with a pair of AquaTechnix LEVER taps WS4-TX-BD
with a pair of AquaTechnix DOME taps WS4-L
with a pair of CaterTap 3" LEVER taps WS4-D
with a pair of CaterTap 3” DOME taps WS4-ML
with single 3” LEVER tap and manual mixer WS4-ML-T
with single 3” LEVER tap and thermostatic mixer
WS4-MM
with Monobloc, single LEVER mixer tap
WB-01
Water Savings and Hygiene Options
WS4-KVS
Knee-Operated, Hands-Free mechanical operation
Includes knee-valve, fixed spout, M-MX91 manual mixer,
water hose & tap hole stopper
Hand Wash Stations - BaSix
WS4-NT
58
Battery-Operated, Hands-Free operation Includes Delabie Tempomatic 3 tap,
M-MX91 manual mixer, water hose & tap hole stopper
WS4-T2
WS4-T2-T
Complete with stainless steel basin, drain boss, integral splashback,
hands-free control and mixing valve.
Soft-touch operated, time flow tap
Model
Includes Delabie Temposoft 2 tap,
M-MX91 manual mixer, water hose & tap hole stopper
Water Savings and Hygiene Options
Soft-touch operated, time flow tap
WS6-KVS
with ‘auto shut-off’ single LEVER tap and manual mixer
WS4-MT-T
with ‘auto shut-off’ single LEVER tap and thermostatic mixer
‘Push-Front’, Hands-Free mechanical operation
Includes fixed spout, M-MX91 manual mixer,
water hose & tap hole stopper
Includes Delabie Temposoft 2 tap, Premix Nano
DLB-732-115 thermostatic mixer, water hose & tap hole stopper
WS4-MT
Description
WS6-NT
Battery-Operated, Hands-Free operation Includes Delabie Tempomatic 3 tap,
M-MX91 manual mixer, water hose & tap hole stopper
Further Options
Further Options
BSX-SPD
WB-01
Optional Soap Dispenser See page 100 for more details
Optional Waste Bin, (for WS6 basin only)
NB: Product accreditation may not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship on parts.
No inclusion is made for labour or site attendance. Dimensions shown in mm unless otherwise stated. Information and numerical data has been prepared as a general guide to the products but intending buyers & users must satisfy themselves as
to the suitability and safety of the products for their particular purposes & duties. The WRAS Approved Product logo is a certification mark which is owned by WRAS Ltd.