GLASS CERAMIC HOB - Operating instructions

AR
GB
GLASS CERAMIC HOB - Operating instructions
30 mm
A
3
2
40 mm
1
53
0
49
,5
B
50
min.
880
50
min.
C
4 mm
25 mm
20 mm
Fig.1
-3-
Fig.2
Fig.3
220-240V 1N ~ H05V2V2-F 3G
380-415V 2N~ H05V2V2-F 4G
220-240V 2~ H05V2V2-F 3G
380-415V 3N~ H05V2V2-F 5G
-4-
220-240V 3~ H05V2V2-F 4G
G
G
L
L
Q
F
R
C
D
E
A
B
Fig.4
-5-
ENGLISH
GB
APPLIANCE (oven) AND THE GLASS-CERAMIC COOKTOP MUST
BE SUITABLY INSULATED in such a way that the heat generated
by the oven, measured on the bottom right of the cooktop,
does not exceed 60°C. Failure to respect this precaution may
determine improper functioning of the TOUCHCONTROL
system.
GENERAL
1.1Carefully read the contents of this leaflet since it provides
important instructions regarding safety of installation, use and
maintenance.
Keep the leaflet for possible future consultation. All the
operations relating to installation/replacement (electrical
connections) must be carried out by specialised personnel
in conformity with the regulations in force.
3.2 Positioning (Fig.1):
The domestic appliance is designed to be built into a worktop
as illustrated in the specific figure. Apply sealant around
the entire perimeter (cut-out dimensions Fig.1B). Fix the
domestic appliance on the worktop by means of the 4 brackets
provided, taking the thickness of the worktop into account
(Fig.1A). If the lower part of the appliance, after installation, is
accessible via the lower part of the cabinet then it is necessary
to mount a separator panel respecting the distances indicated
(Fig.1C). If the appliance is installed with an oven underneath
then the separator is not necessary.
SAFETY WARNINGS
2.1It is recommended to use flat-bottom pans with a diameter
equal to or slightly larger than that of the heated area. Do not
use pans with a rough base to prevent scratching the heat
surface of the cooktop (Fig.2).
This appliance is not suitable for use by children or persons
requiring supervision. Do not let children play with the
appliance.
3.3 Electrical connections:
Before making the electrical connections, check that:
-the ground cable is 2 cm longer than the other cables;
-t he system ratings meet the ratings indicated on the
identification plate fixed on the lower part of the worktop;
-the system is fitted with efficient earthing compliant to the
laws and regulations in force.
If the appliance is not fitted with a cable, use type:
“H05V2V2-F” for a power level of up to 6400 Watts. The crosssection of the cable should be at least 2.5 mm², or 4 mm² for
greater power levels.
The cable should never reach a temperature which is 50°C
above the temperature of the room in which it is installed.
The appliance is designed for permanent connection to
the electricity supply and should therefore be fitted with
an omnipolar switch which has a minimum opening of 3
mm between contacts. The switch should be suitable for
the charge indicated on the appliance data plate and must
conform to all current legislation (the yellow/green earth wire
must not be interrupted by the switch).
The omnipolar switch must be easy to reach once the
installation process has been completed.
2.2 Important:
-Avoid spilling liquid, therefore to boil or heat liquids, reduce
the heat.
-Do not leave the heating elements on with empty pots and
pans or without receptacles.
-When you have finished cooking, switch off the relevant
heating element with the control indicated below.
2.3 Attention:
-Steam cleaners must not be used.
-If the surface is cracked, switch off the appliance to
prevent electric shock.
-This appliance is not intended for use by young children
or infirm persons without supervision.
-Young children should be supervised to ensure they do
not play with the appliance.
-The appliance is not intended to be operated by means
of external timer or separated remote-control system.
2.4Questo apparecchio è contrassegnato in conformità alla
Direttiva Europea 2002/96/EC, Waste Electrical and Electronic
Equipment (WEEE). Assicurandosi che questo prodotto sia
smaltito in modo corretto, l’utente contribuisce a prevenire
le potenziali conseguenze negative per l’ambiente e la salute.
USE AND MAINTENANCE
4.1 Maintenance (Fig.3):
Remove any residues of food and drops of grease from the
cooking surface using the special scraper supplied on request.
Clean the heated area as thoroughly as possible using SIDOL,
STAHLFIX or similar products and a cloth/paper, then rinse
with water and dry with a clean cloth. Using the special scraper
(optional) immediately remove any fragments of aluminium
and plastic material that have unintentionally melted on
the heated cooking area or residues of sugar or food with a
high sugar content. In this way, any damage to the cooktop
surface is prevented. Under no circumstances use abrasive
sponges or irritating chemical detergents such as oven sprays
or stain removers.
Il simbolo sul prodotto o sulla documentazione di
accompagnamento indica che questo prodotto non deve
essere trattato come rifiuto domestico ma deve essere
consegnato presso l’idoneo punto di raccolta per il riciclaggio
di apparecchiature elettriche ed elettroniche. Disfarsene
seguendo le normative locali per lo smaltimento dei rifiuti.
Per ulteriori informazioni sul trattamento, recupero e
riciclaggio di questo prodotto, contattare l’idoneo ufficio
locale, il servizio di raccolta dei rifiuti domestici o il negozio
presso il quale il prodotto è stato acquistato.
INSTALLATION INSTRUCTIONS
4.2 Use:
Use the touch control system in the corresponding position
relative to the individual cooking needs.
Keep in mind that the higher the number, the more heat that
it is produced.
3.1These instructions address specialised installers and serve
as a guide for installation, adjustment and maintenance in
conformity with the laws and regulations in force. If a builtin oven or any other appliance that generates heat must
be fitted directly under the glass-ceramic cooktop, THIS
-6-
4.10 Functioning (Fig.4):
A= ON/OFF button
B= Key button
C= Timer Button +
D= Timer Button E = Key button ON/OFF warning light
F = Cooking zone selection button
G= Double cooking zone ON/OFF warning light
L = Double zone selection button
Q= Cooking zone display
R = Display Timer
after which the temperature will return to a lower value
selected previously. To activate the Heat up function, select
the hotplate by pressing the “+” button until setting 9 is
displayed; if the button is pressed again a decimal point “•”
or the letter “A” will appear on the display (next to the digit
9) for 5 seconds. This means the Heat up function is active.
The desired power level (between 1 and 8) should be selected
within 5 seconds. If power level 9 is selected, the function is
disabled. To deactivate the Heat up function, simply select the
“+” button and hold it down until setting 9 is reached and the
decimal point disappears from the display. When the “Heat
up” function is active, the previously selected temperature
level may be increased by pressing the (+) button. Once the
cooking zone has reached the selected temperature, the “Heat
up” function is automatically deactivated and the hob emits
a BEEP. The cooking zone will operate in a constant manner,
at the set power level.
Based on the model owned, the first time the stove top is
turned on it may be in the safety position, with the LED of
the “Key button warning light” (E) on.
In order to use the stove top it is necessary to press sensor E
for 3 seconds until the warning light turns off.
If the appliance is not used for at least a minute, the key function activates automatically.
4.11 Timer:
This function makes it possible to set the cooking time after
which the zone will turn off.
Complete the following steps to activate it:
-Press the “C” button (00 will appear on the display), or press
the “D” button (99 will appear on the display).
-All cooking zone displays will show a lower case “t”.
-Select the cooking zone that the timer will be used on using
the "F" button.
- Set cooking level using the “F+” and “F-” buttons.
-Set cooking time using the “C” and “D” buttons.
-The end of the established cooking time will be signaled by
an acoustic BEEP (that can be deactivated by pressing “C” or
“D” or “F+” and “F-” on that specific cooking zone).
The display of the zone with an active TIMER will alternately
display a lower case “t” and the temperature level that has
been set.
In order to deactivate the function, before the set time ends,
press “D” and bring the time down to zero.
The Timer may only be activated on one cooking zone at
a time.
-The appliance may be turned on by selecting start-up sensor
A. A zero appears on all displays for 10 seconds. If no operation
is carried out within the next 10 seconds the stove top turns
off.
-It is possible to turn a stove top element on by selecting the
“F+” or “F-” sensors within 10 seconds. If the “F+” sensor is
used, the display shows selection 1, if the “F-” sensor is used,
the display shows selection 9.
-Once this operation has been completed it is possible to
choose temperature adjustments using the “+” or “-” buttons.
-The stove top element may be turned off by selecting “0”
with the F sensor, after 3 seconds the cooking area turns off.
It is also possible to turn a stove top element off by selecting
the “F+” and “F-” sensors at the same time.
-The stove top may be turned off by selecting the main startup sensor A. If all stove top elements are on “0”, the stove top
turns off after 10 seconds.
-If the stove top is equipped with elements with an extension,
the second zone will start-up after it verifies that:
-The LED of the B key button is turned off, otherwise it will
disengage it.
-Press button A to turn the stove top on.
-Select the desired element and adjust the power using the
“F+” or “F-” buttons.
-Once the power is adjusted select the L button to activate the
double zone. Press the L button a second time to deactivate
the double zone.
-If an object is placed above the controls, the stove top will
automatically change to the OFF position.
When an element is brought to the OFF position and the glass
surface temperature is above 50°, the cooking area involved
will show an illuminated “H“ on its display.
-The B function blocks stove top functioning at the moment
of selection. Ex: if the function is activated while the stove top
already has two zones turned on, the program is blocked, even
if trying to turn on another zone. The same thing happens if
the appliance is turned off and the function is activated, the
stove top does not turn on.
In order to activate or deactivate it keep a finger above sensor
B for about two seconds. The function is active when the E
warning light is turned on.
Even with the key button is active, the A button works the
same.
4.12 Minute Minder:
This function makes it possible to set and acoustic reminder
during the cooking time that will not turn off the cooking zone.
Complete the following steps to activate it:
-Press the “C” button (00 will appear on the display), or press
the “D” button (99 will appear on the display)
-Set cooking time using the "C" and “D” buttons.
-At the end of the established timeframe there will be an
acoustic BEEP (it can be deactivated by pressing “C” or “D”).
In order to deactivate the function, before the set time ends,
press “D” and change the time to zero.
The Minute Minder can be activated even while all cooking
zones are on.
5.0THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
4.4Heat up (Rapid heating):
The Heat up function can be used to set the cooking zone
to its maximum temperature for a specified period of time,
-7-
“D”
TIMER
Minute Minder
4.12
“C”
00
“D”
99
“D” “C”
. “D”
“C”
“D”
Minute Minder
5.0
-8-
4.2
L
OFF
OFF
50
4
4.10
H
B
+
-
B
E
A
4.4
Heat Up
Heat Up
LED
Heat Up
(E)
“+”
E
LED
“A”
“•”
“Heat Up”
Heat Up
A
“+”
0
10
10
“Heat Up”
“+”
Heat”
10
“Up
“F-”
1
“F+”
“F+”
“F-”
9
:(TIMER)
4.11
“-”
F
“+”
“0”
“C”
“D”
00
“F-” “F+”
99
A
“0”
“t”
10
“F”
“F-” “F+”
“D” “C”
B
LED
A
“D”
“C”
BIP
“F-”
“F+”
“F-”
L
“t”
(TIMER)
-9-
“F+”
AR
1.1
1
3.2
2.1
1B
1A
4
2
1C
2.2
3.3
2.3
“H05V2V2-F”
2.4
4.1
3
3
3.1
- 10 -
3LIP0318
Download PDF
Similar pages