WD-3274RHD
WD-3276RHD
Washing Machine
OWNER'S MAINUAL
Pleasereadthismanualcarefully,
itprovides
instructions
onsafeinstallation
use,andmaintenance.
Retainitforfuturereference.
Record
themodelandsedalnumbers
ofyourmachine.
Quotethisinformation
toyourdealerifyourequireservice.
e
Lave-UngeAutomaitque
LG.
II contient,
rutiliseitonet
3 sedemier.
num6rodes6riedulave-linge.
Automatic Process From Washing To Drying.
Automaticprocessfrom washing to drying can be selectedeasily,
More economical
by Intelligent
Wash System
Intelligent Wash System detects the amount of load and water
temperature, and then determines the optimum water level and
washing time to minimize energy and water consumption.
Direct Drive System
The advanced Brush[ess DC motor rotates the drum directly
without belt and pulley.
SPIN
TIME DELAY
Child-Lock
The Child-Lock system has been used to prevent children from
pressing any button to change the program during operation.
@
Low noise speed control
system
By sensing the amount of load and balance, it evenly distributes
load to minimize the spinning noise level.
Auto
Restart
If the washing machine is turned off by a power failure, it will restart
automatically from the position it stopped at adjusting accordingly.
Important Safety Information ..................................................... 3
Specification ..............................................................................
4
Installation ..................................................................................
5
Preparation Before Washing .................................................... 10
Adding detergent .....................................................................
11
Cycles ....................................................................................
12
How to Use Washer .................................................................
13
Maintenance ............................................................................
21
Troubleshooting Guide ............................................................ 24
Warranty ..................................................................................
27
READ ALL INSTRUCTIONS
BEFORE USE
Foryoursafety,theinformation
inthismanual
mustbefonowed
tominimize
theriskoffire
orexplosion,
electric
shock,ortopreventproperty
damage,personalinjury,orlossoflife.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
: To reduce the risk of fire, electric shock, or injury to persons when using the washer,
follow basic precautions, locluding the following:
• Read all instructions before using the washer.
• Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry cleaning solvents, or other
flammable or explosive substances, as they give
off vapors that could igniteor explode.
• Do not add gasoline, dry cleaning solvents, or
other flammable or explosive substances to the
wash water, These substances give off vapors
that could ignite or explode.
• Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for 2 weeks or more, HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not
been used for such a period, before using the
washing machine, turn on all hot water faucets
and let the water flow from each for several
minutes, This will release any accumulated
hydrogen gas, As the gas is flammable, do not
smoke or use an open flame during this time.
• Do not allow children to play on or in the washer,
Close supervision of chitdren is necessary when
the washer is used near children.
• Before the washer is removed from service or
discarded, remove the door to prevent children
from hiding inside,
• Do not install or store the washer where it will
be exposed to the weather,
• Do not tamper with controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or published user-repair instructions
that you understand and have the skills to carry
out.
• See InstallafioeInstructions for grounding
requirements.
• Do not use heat to dry articles containing foam
rubber or similarly textured rubber-like materials,
• Interior of washer and condensing duct should be
cleaned periodically
by qualified
service
personnel
• ALWAYS follow the fabric care instructions
supplied by the garment mantdacturer.
• Do not place items exposed to cooking oil in your
dryer, items contaminated with cooking oils may
contribute to a chemical reaction that could cause
a load to catch fire,
• Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
SAVE THESE INSTRUCTIONS
GROUNDING
INSTRUCTIONS
This appliance must be grounded, in the event of malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for electric current, This appliance is equipped with a
cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance,
• Do not use an adapter or otherwise defeat the grounding plug.
• If you don't have the proper outlet, consult an electrician.
WARNING
: Improper connection of the equipment-grounding
conductor can result in risk of electdc
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
f_:_
Drawer
(For detergent end
fabric softener)
Power plug
olf the supply cord is damaged,
it must be replaced bythe
manufactureror its serviceagents
or a similarly qualifiedpersonin
orderto avoid a hazard.
_,
Control panel
Drainhos
Drum
Lower cover
Adjustable feet
Drain pump flit
Lowercovercap
Drain plug.
• Name
• Power supply
• Size
•
•
•
•
Weight
Wash capacity
Dry capacity
Max. Watt
• Spin speed
• Water consumption
• Permissible water pressure
: Front-loading Washing Machine
: 120V~, 60Hz
: 235/8 X 235/8 X 331/2 (inches)
600 X 600 X850 (ram)
: 1561/2 Ibs. (71 kg)
: 152/5 Ibs. (7.0 kg)
: 84/5 Ibs. (4.0 kg)
: 1200W
: No Spin/400/800/1000/1400
: 18gaL (670
: 4.5 - 145 PSi (30 - 1000 kPa)
÷ The appearance and specifications may be varied without notice to raise the unit's quality,
• Accessories
Tie strap
Hot/Cold (1 each)
Wrench
to secure drain hose to standpipe,
inlet hose, or laundry tub
Install or store where it will not be exposed to temperatures
below freezing or exposed to the
weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other
vermin_ pay particular attention to keeping the appliance and its surroundings
in clean condition
all times.
Any damage which may be cause by cockroaches or other vermin will not he covered by the
appliance guarantee.
• Shipping
The appliance is fitted
• Removing
with shipping
shipping
bolts to prevent
internal
at
damageduring transport.
bolts
1. To prevent internaldamageduring
transport, the special 3 bolts are locked.
Beforeoperatingthe washer, remove
the bolts along with the rubber bungs.
3. Take out the 3 bolts along with the rubber
bungs by slightlytwisting the bung. Keep
the 3 bolts and the spanner for future use.
• If they are not removed, it may cause heavy
vibration,noiseand malfunction.
• Wheneverthe applianceis transported,the
transit bolts must be refitted.
cap
2. Unscrewthe 3 boltswith
the spanner supplied.
4. Close the holeswith the caps supplied.
• Installation
place
requirement
Drain
Hose
Level floor :
Allowable slope under entire washer is 1_.
Power outlet :
/
Laundry
Tub
approx.
Must be within 60 inches(1.5 m) of either
side of the washer. Do not overload the
outlet with more than one appliance.
Additional Clearance :
If the washer is installed inside a closet or
alcove, the following clearances are
required:
4 inches (10 cm) rear, 1 inch (2.5 cm) side
Do not place or store laundry products on
top of washer at any times.
They can damage the finish or controls.
• Electrical
connection
1. Do not usean extensioncord or double adapter.
2. If the supply cord is damaged,it must be replacedby the manufactureror its serviceagents
or similarlyqualifiedperson in order to avoid a hazard.
3. Always unplug the machine and turn off the water supply after use.
4. Connectthe machine to an earthed socket in accordancewith currentwiring regulations.
5. The appliancemust be positionedso that the plug is easily accessible.
• Repairs to the washing machine must only be carriedout qualified personnel.Repairs carriedout by
inexperiencedpersons may cause injury or serious malfunctioning.Contactyour localservice center
• Do not install your washingmachine in rooms where temperaturesbelowfreezing may occur. Frozen
hoses may burst under pressure.The reliability of the electroniccontrol unit may be impairedat
temperaturesbelowfreezing point.
• If the appliance is deliveredin the winter months and temperaturesare belowfreezing : Store the
washing machineat roomtemperaturefor a few hoursbefore putting it intooperation.
• Washing Machine is to be connected
Old hoses should not be used.
• Connecting
water
to the water mains using new hoses
supply hose
4.5 ~ 145 PSI (30~1000 kPa)
• Don't strip or crossthread when connecting
inlet hose to the valve.
• 1/the water supplypressure is more than
1000 kPa, a pressure reducer device should
be installed.
•Two Sealing washer are suppliedwith the
water inlet hoses to preventwater leaks,
• Checkwater tightnessof washing
machineconnectionsby turningthe tap
completelyon.
• Periodicallycheckthe conditionof the
hoseand replacethe hose if necessary.
• Make sure that there is no kink in the
hoseand that it is not crushed.
Hot wate_
Cold
•The Inlet hose which hasred connectoris
for the hot water tap.
• Hot and cold water faucets Must be
installedof your washer'swater inlet.
This equipment is not designed for maritime use or for use mobile installations such as
caravans, aircraft etc.
Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday),
especially if there is no floor drain(gully) in the immediate vicinity.
When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the
door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
of suffocation !
Keep all packaging well away from children
• Installation
of drain hose
• When installingthe drain hose at a sink,
secure it so it cannot break away, causing
flooding and damage.
• Proper securing the drain hose will protect
the floor from damage due to water
leakage.
Laundrytub
Retainer
Tie _'_
• The drain hoseshould not be placed
higher than 40" abovethe floor.
• Proper securing the drain hosewill
protect the floor from damage due to
water leakage,
,i_ianx.
24,0"
• Level adjustment
1. Levelinga the washing machine properly
preventsexcessivenoise and vibration.
Installthe applianceon a solid and level
floor surface, preferablyin a corner of
the room.
2. If the floor is uneven,adjust the
adjustablefeet as required.(Do not
insert pieces of wood, etc. under the
feet)
Make sure that all four feets are stable
and restingon the floor and then check
that the applianceis perfectly level. (use
a spirit level)
-',_Diagonal Check
When pushing down the edges of the
washing machine top plate diagonally, the
machine should not move up and down at
all. (Please, check both directions)
If machine rocks when pushing the machine
top plate diagonally, adjust the feets again.
WARNING - To reduce the risk of fire, electric shock, or injury to persons, read the
IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
1. Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your
garment and how it should be washed.
2. Sorting
To get the bestresults,Sortclothesintoloadsthat can be washedwith thesame wash cycle.
Watertemperatureand spin speedand differentfabricsneedto be washedin differentways.
Always sort dark colors from pale colors and whites. Wash separatelyas dye and lint
transfercan occur causing discolorationof white etc. If possible,do not wash heavily
soiled items with lightlysoiled one.
Soil (Heavy, Normal,Light)
Color (White,Lights, Darks)
Lint (Lint Producers,Collectors)
3. Check
before
Separate clothesaccordingto amount of soil.
Separatewhite fabrics from coloredfabrics.
Wash lint producersand lint collectors
separately.
loading
• Combine large and small items in a load. Load large items first. Large items should not be more
than half the total wash load,
Do not wash single items, This may cause an out-of-balance
load. Add one or two similar items.
• Checkall the pockets to make sure
that they are empty. Things such
as nails, hair clip, matches,pens,
coins, and keys can damageboth
your washer and your clothes.
• Closezippers, hooks,and strings
to make sure that these items don't
snag on other clothes.
• Pre-treatdirt and stains by
brushinga little detergent dissolved
in water onto stains like collars and
cuffs to help shift dirt.
• Adding detergent
1. The Dispenser
and fabric softener
Drawer
3. The liquid bleach drawer.
• Do not open the detergentdrawer during
water fill cycle.
• Bleachwill be dispensed automatically
after the detergent has had time to work.
• Do not fill past MAX indicator.
Detergent
for wash
Fabric
sotlener
Uquid
BIeadl
2. Adding Fabric Softener
4. Detergent
usage
• The detergent should be used according to the
instruction of the detergent mam4Jhcture.
• Do not exceed the maximumfill line.
Overfillingcan cause early dispensing
of the fabric softenerwhich could stain
clothes.
• Do not leave the fabric softener in the
detergentdrawer for more than 2 days.
(Fabric softenercould harden)
• Softenerwill automaticallybe added
during last rinsecycle.
• Do not open the drawerwhen water is
supplied.
• Solvents(benzene,etc.) are not
allowable.
Do not pour fabric softener
directly on the clothes
•[[too muchdetergent is used morethan the
recommendedamount,too many suds can
occur and this willdecrease the washingresuh
or cause heavy load to the motor,causing a
malfL1nclion.
• Use powder detergent onlyJbr the,[kont
loading washer.
• Detergentusagemay need to be adjusted
for water temperature,water hardness,
size, and soil levelof the load. For best
results, avoidoversudsing.
• Detergent is dispensed at the beginning of
the cycle.
• Recommended
WASH
SANITARY
courses according
to the laundry type
First check if
laundryis machine
washable.
HOT/COLD
white cotton, linen
WASH/
towel
and
DRY sheets...)
WASH
Color fast gaments
Jeans, Tshirts,
Shorts,pajamas..,)
Wash
EXTRARINSE
Ibs.
(7.0kg)
EXTRAWASH
152/5
WaehlDry
84/5
Ibs.
(4.0kg)
WASH
PERM,
TAPCOLD/COLD
WASH/DRY
WASH
RINSE
+
SPiN
If you wish to rinse
more,theExtra
Rinsefunction will
removeany trace
WASH/ of detergents.
DRY
WOOL/
SiLK
WASH
Machinewashable
woolenswith pure
new wool only
EXTRARINSE AUTO
97
286
82
271
COLD,COLD
EXTRAWASH
(T,ME)
DRYONLY
Polyamide,Acrylic,
Wash
Polyester
WARM/COLD 84/5
Ibs.
(WARM/WARM,
(4.0kg)
PRESS
EXTRARINSE AUTO
EXTRAWASH
DRYONLY (TIME)
WARM/COLD Wash
EXTRARINSE
(WARM/WARM,
152/5 Ibs.
HOT/COLD, (7.0kg)
EXTRAWASH
COT[ON WASH/ whiteand
light_YcottonSOiled
TAPCOLD/COLtWaehlDry
DRY
-
COLD/COLD)
EXTRA
EXTRARINSE
WASH
77
EXTRARINSE AUTO
-
EXTRAWASHDRY
ONLY (TIME)
Wash
COLD/COLD 152/5 Ibs. EXTRARINSE
(WARM/COLD, (7.0kg)
WARM/WARM,
TAPCOLD/COLE
WashlDrY84/5
Ibs. EXTRARINSE AUTO
(4.0kg)
DRYONLY (TIME)
COLD/COLD
(WARM/COLD, 42/5 Ibs.
WARM/WARM, (2.0kg)
TAPCOLD/COLE
EXTRARINSE
265
32
221
56
÷ EXTRA WASH : If the laundry is heavily soiled, "EXTRA WASH" course is recommended.
EXTRA WASH is available in COTTON, SANITARY and PERM. PRESS
Program.
• To start, press the POWER button.
• To start, press the POWER button.
• Press the START/PAUSE button.
• Initial condition
- Wash
Main Wash Only
- Rinse
3 times
- Spin
800 rpm
- Temp.
- Program
Warm/Cold(Wash/Rinse)
Cotton
• Select the conditions which you want to
use, by pressing each button.
For selecting the correct _cle, please refer to
pages 14 ~ 20.
• Press the START/PAUSE button.
• The Beep On/Off function can be set by
pressing and holding the OPTION and
DRY button simultaneonly.
• The Beep On/Off function can be set at
any time and it is automatically canceled
when power failure occur.
Also the Beep On/Off function works
when power is off.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(1) BUTTON : OPTION
(4) CHILD LOCK
(7) BUTTON : START/PAUSE
(2) BUTTON : WATER TEMP.
(3) BUTTON : SPIN
(5) BUTTON : TIME DELAY
(6) BUTTON : DRY
(8) DIAL : PROGRAM
(9) BUTTON : POWER
OPTION
• By pressing the OPTION
button, the wash type can
be selected.
- EXTRA RINSE
- EXTRA WASH
- EXTRA RINSE +EXTRA WASH
- DR Y ONL Y[WASH/DR Y]
• If the laundry is heavily soiled, "EXTRA
WASH" course is effective.
• This option can be used to add a rinse for
people with sensitive skin. Selecting the
EXTRA RINSE button is also
recommended when washing heavily
soiled fabrics which needs a lot of
detergent, or when the wash load
contains towelling fabrics that have a
greater tendency to retain detergent.
If lamp turns on, that function has been
selected.
• EXTRA WASH is available in SANITARY,
COTTON and PERM. PRESS.
The required lamp will light upJbr
identification.
• DRY ONLY option can be used when you
want to only dry without any other
programs such as wash, spin, etc.
• Select any of the programs SANITARY
COTTON, PERM. PRESS, RINSE+SPIN
in WASH/DRY and then DRY ONLY by
pressing the optionbutton.
• Press TEMP, to cycle through
the temperature choices,
• Select a water temperature
based on the type of load you
are washing. Use the warmest
water safe for fabrics, Follow
garment label instructions.
• Warm dnses leave the loads
• By pressing the SPIN button,
the spin rpm can be chosen,
-RINSE HOLD
_
w,_v_
w_oLo
_
Tec_._u_
- NO SPIN
SPIN
TEMe
- 400
- 800
-1000
-1400
dryer than cold rinses, Warm
rinses increase wrinkling, In cold
climates, a warm rinse makes the load mere
comfortable to handle. Cold rinses save energy.
• Warm rinses are regulated at approximately 75 _F
(24 _C), This is a cooler warm rinse than you are
used to, but it saves energy and gives proper
rinsing, The load is a comfortable temperature
remove from the washer,
• Spin rpm is available according to the program as
foltuws.
[Wash Programs]
- SANITARY & COTTON & RINSE+SPIN
800--)1000-.)1400-.)Rinse HOld-.)NoSpin.-.)400
- PERM. PRESS
800,--)1000-.)Rinse Holri-YNo Spin,--)400
- WOOL/SILK
• Water temperature can be selected as below
according to the program,
- SANITARY
HOT/COLD
- COTTON
WARM/COLD "i) WARM/WARM-)HOT/COLD
400,--)800.-.)1000.-.)RinseHold.-.)No Spin
[Wash/Dry Programs]
- SANITARY & COTTON & RINSE+SPIN
1400-.)800-.)1000
-.)
TAP COLD/COLD-.) COLD/COLD
- PERM. PRESS
1000-) 800
- PERM. PRESS
WARM/COLD-)WARM/WAR-)TAP
COLD/COLD-)COLD/COLD
- WOOL/SILK & RINSE+SPIN
COLD/COLD -') WARM/COLD --)
WARM/WARM-)TAP COLD/COLD
Selected temperature's lamp turns on,
For the more detailed information,ple_e refer to thepage12.
• If NO SPIN is selected, the washer stops
after draining water,
The required lamp will light up for
identification.
TemperatureGuide
Wash Water Temperature
Suggested Fabdc_
Hot
Whitesanti pasteis
111_F (_
C) or above
Heavy anti greasy solts
Warm
Bright colors
90_-110_F (3Z- 43_C)
Moderateto light solIs
Cold
Colo_ that bleed or fade
70_-90_F (21_-3Z C)
Light soils
Inwash water temperatures colder than 70" F (21' C),
detergents do not dissolve weU,Soils may be difficultto
remove.
• [s selected by pressing the SPIN button
repeatedly this function leaves clothes in the
washer; suspended in the water after a rinse
without entedng into spin,
• To proceed through to a drain or spin,
once the rinse hold function is completed
using to program dial scroll to the required
program, (Spin or Pump)
The required
lamp
will light up for identOTcadon.
If you choose to lock the buttonson the
control assemblyto preventtampering,this
functionmay be selected.
•ChildLockcanbe setby pressingandholdingthe
SPINbuttonandTIMEDELAYbutton
simultaneousl
SPIN
T_MEDEALY
Preparingwashing beJorestarting "Time
Delay"
- Turnon the water tap.
- Load laundryand close the door.
- Placethe detergent and fabric softenerin
the drawer.
• Howto set "TIME
Whenchildlock is set,all buttonsare
inoperable.
•TodeactivateChildLocksystem,pressandhold
theSPINandTIMEDELAYbutton
simultaneously
again.
•Tochangeto thedesiredprogram,whilstin child
lockmode.
1. PressandholdbothSPINandTIMEDELAY
togetheronceagain,
Z. PresstheSTART/PAUSE
button.
3.Selectthedesiredprogramandpressthe
START/PAUSE
buttonagain.
DELAY"
- Press POWER button.
- Turn the PROGRAMdial to select
the programyou require.
- Press TIME DELAYbutton and set the
desired time.
- Press the START/PAUSEbutton.
(":" blinks.)
• If TIME DELAYbutton is pressed,"3:00" is
displayed.The maximumdelayedtime is
19:00 hoursand the minimumtime is 3:00
hours.
• Each pressingof the button advanceson
time delay by one hour.
• To cancel the timedelay, pressthe
POWERbutton.
• TIME DELAY is 'expected time' from the
present to the completion of washing cycle
or selected process (Wash, Rinse or Spin).
•Thechildlockcanbesetat anytimeandit is
automatically
canceledwhenoperational
errors
occur.AIsoChildLockworkswhenpowerisoff.
• According to the condition of water supply and
temperature, the delayed time and the actual
washing time may vary.
• This washer-dryer's automatic
process from washing to drying
can be selected easily.
A,_O _y
t_E_Y
o_
• For most even drying, make sure
all articles in the clothes load are
similar in material and thickness.
• Do not overload dryer by stuffing
too many articles into drum, Items
must be able to tumble freely.
• If you open door and remove load before dryer has
finished its cycle, remember to press the
START/PAUSE button.
• Your dryer can handle a load of up to
84/5Ibs.(4kg) dry weight of articles.
• When loading,shake out each handfulof
clothesso that they can tumble freely.
Items should not be loaded in a tangled
condition, as this will lengthenthe drying time.
Woolen Articles
- Do not tumble dry woolen articles. Pull them
to their original shape, and dry them flat.
Woven and LoopknitMaterials
• Use your Automatic Cycles to dry most loads.
Electronic sensors measure the temperature of
the exhaust to increase or decrease drying
temperatures for faster reaction time and tigher
temperature control,
• If a load is not as dry as you like, complete drying
using a time cycle.
- Somewoven and Ioopknitmaterialsmay
shrink, byvarying amounts,dependingon
their quality.
- Always stretch them out immediatelyafter
drying.
PermanentPress and Synthetics
- Do not overloadyour dryer
• By pressing the DRY button, the drying time can he
selected.
• These drying times are given as a guide to help you
set your dryer for manual drying. Drying times can
vary greatly depending on dampness, room
temperature and type of fabric and your own
experience will be your best guide,
• AUTO (NORMAL) Cotton 84/5Ibs. (4.0 kg)
• TIME DRY
From15rm. to150rnin.eslestable
15min,isaddedbypressing
DRYbutton.
30 rain.
Cotton 21/5Ibs, (1.0 kg)
60 rain.
Cotton43/7 Ibs, (2.0 kg)
150 min, Co,on 65/8Ibs, (3.0 kg)
The Estimated drying time varies
from the actual drying time with an
Automatic. The type of fabric, size
of the load, and the dryness
selected affect drying time.
- Take out permanent press articlesan soon as
the dryer stopsto reducewrinkles.
Fiber or Leather Materials
- Always check the manufacture'sinstructions.
Baby Clothes and Night Gowns
- Always check the manufacture'sinstructions.
Rubber and Plastics
- Do not dry any itemsmade from or containing
rubber or plastics,such as:
a) aprons, bibs, chair covers
b) curtains and tablecloths
c) bathmats
Fiberglass
- Do not dry fiberglassarticles in your dryer.
Glass particlesleft in the dryer could be picked
up by your clothesthe next time you use the
dryer and irritate your skin.
START/PAUSE
• This START/PAUSE button is used to
start wash cycle or pause the wash cycle
• 9 programs are available according to
the laundry type
• Lamp will light up to indicate selected
program
• If temporary stop of wash cycle is
needed, press the START/PAUSE
button
• When in Pause, the power is turned off
automatically after 4 minutes
• When START/PAUSE button is pressed,
the Cotton program is automatically
selected
• NB. The door will not open before 1 to 2
minutes when Pause is selected,
or at the end of the wash cycle
- By turning the Program dial, the program
is selected in order of "COTTON-->
PERM PRESS->WOOL/SILK->
RINSE+SPIN->÷RINSE+SPIN->
÷PERM PRESS->÷COTTON->
÷SAN ITARY->SANITARY"
[ ÷:WASH/DRY]
Regarding to the laundry type for eaeh
program Please refer W the page12.
[WASH]
IWASH/DR Y]
-RINSE+SPIN
-RINSE+SPIN
-WOOUSILK
-PERM. PRESS
-PERM. PRESS
-COITON
-COTTON
-SANITARY
-SANITARY
• Press the Power button to turn power on
and off
• To cancel the TIME DELAY function, the
Power button should be pressed
• When the Power button is pressed, the
washer is ready for Cotton program
• If you want to advance into the washing
cycle without changing the program, just
press START/PAUSE button and then
the washer will proceed
lnitial program
- Cotton Program, Main
Normal Rinse, 800rpm,
wash,
Warm/Cold
• When washing cycle is completed,
"End "is displayed
on the "Multi
display'.
• When child lock is selected, the
,,t.t.
r _ ,, is displayed.
• When time delay is selected, it shows
the remaining times to finish the selected
program.
• During washing cycle, the remaining
washing time is displayed.
• Recommended program by
manufacturer.
[WASH]
- SANITARY
: Approx.1 hourand37 minutes
• If the washer encounters a fault during
operation, the associated fault will be
displayed.
"PE":
Water pressure sensing error
"FE" : Problem ofoverfilling
water
"dE"
: Door is not closed
- COTTON:Approx.1hourand22 minutes
- PERM.PRESS:Approx.1 hourand
17minutes
- WOOL/SILK
: Approx.56minutes
- RINSE+SPIN
: Approx.32 minutes
"LE ": Over load in motor.
[WASH/DRY]
- SANITARY
:Approx.4 hoursand46 minutes
"rE ": Over load in motor.
- COTTON:Approx.4 hoursand31minutes
",'E": Water inlet trouble
- PERM.PRESS:Approx.4 hoursand
25 minutes
"OE":
Drainage trouble
"UE" : Unbalanced load
"/_ E ": water temperature trouble
"dHE ": Dry heater or thermostat
trouble
If these error letters are displayed, please
refer to the troubleshootingpage26 and
follow the guide.
- RINSE+SPIN
: Approx.3 hoursand
41 minutes
• The washing time may vary by the
amount of laundry, water pressure,
water temperature and other washing
conditions.
• If an unbalanced load is detected or if
the suds removing program operates,
the wash time may be extended.
(Max. increasing time is 45minutes.)
• Whendryingcycleis completed,
"Cd" [COOLDOWN]is
displayedontheMulti display.
• The COOL DOWN is setting
automatically when a drying
cycle is complete.
• When you are not remove a load
of clothes from the dryer as soon
as it stops, wrinkles can form.
• The COOL DOWN operating
periodically tumbles, rearranges
and fluffs the load to avoid
wrinkles without heat for up to 4
hours.
• The "Cd " message will continue
to display until the clothes are
removed or the START/PAUSE
button is pressed.
It is impossible to give exact
drying times. Conditions from
home to home vary and directly
affect drying times. The length of
time it takes to dry loads will
depend on several variables.
• These cycles have a longer cool
down period to reduce wrinkling.
• The automatic cycle will
determine the time needed and
often provides the best results.
• Modifiers allow you to further
customize your cycles and save
energy.
-_ Beforecleaningthe washerinterior,unplugthe electrical powercordto avoid electricalshock to
avoid electricalshock hazards.
÷ When disposingof the appliance,cut offthe mainscable, anddestroythe plug Disablethe door
lockto preventyoung childrenbeingtrappedinside.
• The water inlet filter
-"/E "error message will blink on the control panel when water does not enter the
detergent drawer.
- If your water is very hard or contains traces of lime deposit, the water inlet filter may
become clogged.
It is therefore a good idea to clean it from time to time.
1. Turn off the
water tap.
2. Unscrew the
water inlet
hose.
3. Clean the
filter using a
hard bristle
brush.
4. Tighten up
the inlet
hose.
• The drain pump filter
-.'.te
Thedrainfilter collectsthreadsandsmallobjectsleft in thelaundry.
Checkregularlythatthe filteriscleanto ensuresmoothrunningof yourmachine.
_,CAUTION
Firstdrain usingthe drain hose and thenopen the pumpfilter to remove
whateveranythreads or objects.
Be carefulwhen drainingif the water is hot.
÷ Allowthe water to cool down beforecleaningthe drain pump,carryingout emergency
emptyingor openingthe door in an emergency.
1. Open the lower cover
cap (_:) by using a
coin. Turn the drain
plug (_) to pull out
the hose.
2. Unplugthe drain plug (_4),
allowingthe water to flow out. At
thistime use a vessel to prevent
water flowing on to the floor. When
water does not flow any more, turn
the pump filter (_) open to the left.
3. Remove out any foreign material
from the pump filter (Z_.).After
cleaning, turn the pump filter (13)
clockwiseand insert the drain
plug ( 2.)to the original place.
close the lower cover cap.
• Dispenser drawer
After a while detergents and fabric softeners leave a deposit in the drawer.
• It should be cleaned from time to time with a jet of running water.
• If necessary it can be removed completely from the machine by pressing the catch
downward and by pulling it out.
• To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
• The drawer recess
Detergent can also accumulate insidethe recess which should
be cleaned occasionally with an old toothbrush.
• Once you have finished cleaning, replace the drawer and run a
rinse cycle without laundry.
• The washing drum
• If you live in a hard water area, limescale may continuously build up in places where it cannot be
seen and thus not easily removed.
Over time the build up of scale clogs appliances, and if it is not kept in check these may have to
be replaced.
• Although the washing drum is made of Stainless steel, specks of rust can be caused by small
metal articles (paper clips, safety pins) which have been left in the drum.
• The washing drum should be cleaned from time to time.
• If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine
use.
Descaler may contain chemicals that may damage part of your washing machine.
Remove any spots with a stainless steel cleaning agent.
Never use steel wool.
• Cleaning your washer
1. Exterior
Proper care of your washer can extend its life.
The outside of the machinecan be cleanedwith warm water and a neutralnon abrasive
householddetergent.
Immediatelywipe off any spills. Wipe with damp cloth.
Try not to hitsurface with sharpobjects.
÷ IMPORTANT:Do not use methylatedspirits, diluents or similar products.
2. Interior
Dry aroundthe washer door opening,flexible gasket and door glass.
Run washer througha completecycle using hot water.
Repeat processif necessary.
Remove hard water deposits using only cleaners labeled aswasher safe.
• Cold condition
If the washer is stored in an area where freezing may occur or moved in freezing
temperatures,follow these instructionsto preventdamage to the washer:
1. Turn off water supply tap.
2. Disconnecthoses from water supply and drain water from hoses.
3. Plug electricalcord into a properlygrounded electricaloutlet.
4. Add lgallon(3.8L) of nontoxicrecreationalvehicle(RV)antifreeze intoan emptywash drum.
Close the door.
5. Set spin cycle and let washer spin for 1minuteto drain out all water.
Not all of the RV antifreezewill be expelled.
6. Unplugelectricalpowercord, dry the drum interior,and close the door.
7. Removedispenser drawer, drain and dry excessivewater from the compartments.
8. Store washer in an uprightposition.
9. To removeantifreezefrom washer after storage, run empty washer
througha completecycle usingdetergent.Do not add wash load.
÷ Thiswashingmachineis equippedwith automaticsafetyfunctions which detectanddiagnosefaults
at an early stage andreactappropriately.
Whenthe machinedoes notfunction properlyor doesnotfunctionat all, checkthe followingpoints
beforeyoucontactyour serviceprovider.
Rattling and
clanking noise
• Foreign objects such as coins or
safety pins maybe in drum or
pump.
Stop washer and check drum
and drain filter.
If noise continues after washer
is restarted, call your authorized
service centre.
Thumping sound
• Heavy wash loads may produce
a thumping sound. This is usually
normal
If sound continues, washer is
probably out of balance. Stop and
redistribute wash load.
Vibrating noise
• Have all the transit bolts and
packing been removed?
• Are all the feet resting firmly on
the ground?
If not removed during
installation, refer to Installation guide
for removing transit bolts.
Wash load may be unevenly
distributed
in drum. Stop washer and
rearrange wash load.
Waterleaks.
• Fill hoses or drain hose are loose
at tap or washer.
Check and tighten hose connections.
• House drain pipes are clogged.
Unclog drain pipe. Contact plumber
if necessary.
Too much detergent or unsuitable
detergent may cause excessive
foaming which may result inwater
leaks.
Oversudsing
Water does not enter
washer or it enters
slowly
Water in the washer
does not drain or
drains slowly.
• Water supply is not adequate in
area.
Check another tap in the house.
• Water supply tap is not
completely open.
Fully open tap.
• Water inlet hose(s) are kinked.
Straighten hose(s),
• The filter of the inlet hose(s) are
clogged.
Check the filter of the inlet hose(s).
• Drain hose is kinked or clogged.
Clean and straighten the drain hose.
• The drain filter is clogged.
Clean the drain filter.
Washer
does
notstart •Electrical
power
cordmaynot
beplugged
inorconnection
maybeloose.
•House
fuseblown,
circuit
breaker
tripped,or
apower
outage
hasoccurred.
•Water
supply
tapisnotturned
Make sure plug fits tightly in wall
outlet.
Reset circuit breakeror replacefuse
Do not increasefuse capacity
If problemis a circuitoverload, have
it correctedby a qualified electrician
Turn on water supply tap
on.
Washer
won't
spin
÷ Check that the door is firmly
shut
Close the door and press the
Start/Pause button After pressing
the Start/Pausebutton, it may take
a few momentsbefore the clothes
washer begins to spin The door
must lock beforespin can be
achieved
Door
does
notopen
Once started,the door can not be
opened for safety reasons
Wait one or two minutes before
opening the door to give the electric
locking mechanismtime to release
Wash
cycle
time
delayed
The washingtime may vary by the
amount of laundry, water
pressure,water temperature and
other using conditions
If the imbalanceis detected or if the
suds removingprogram works, the
wash time shall be increased
Dryproblem
• Does not dry
Do not overload
Check that the washer is draining
properly to extract adequatewater
from th load
Clothes load is too small to tumble
properly Add a few towels
• Water supply is not adequate in area
• Water supply taps are not completely
open,
• Water inlet hose(s) are kinked,
• The filter of the inlet hose(s) are
clogged.
Check another tap in the house,
Fully open tap.
• Drain hose is kinked or clogged,
• The drain filter is clogged.
Clean and straighten the drain hose,
Clean the drain filter,
• Load is too small,
• Load is out of balance.
Add 1 or 2 similar items to help
balance the load.
• The appliance has an unbalance
detection and correction system. If
individual heavy articlos are loaded
(ex. bath mat, both robe, arc,), this
system may stop spinning or even
interrupt the spin cycle altogether,
• If the laundry is still too wet at the end
of the cycle, add smaller articles of
laundry to balance the load and repeat
the spin cycle.
Rearrange load to allow proper
spinning
Straighten hose(s),
Check the filter of the inlet hose(s),
Close the door.
• Is the door
opened?
÷ If "alE"is not released, call for service,
Unplug the power plug and call for
service,
• Water overfills due to the faulty water
valve,
• Water level sensor has malfunctioned.
Close the water tap,
Unplug the power plug.
Call for service,
• Over load in motor.
• Over load in motor.
• Checkwatersupply.
Turn the tap on.
If 'dHE" is not released, unplug
power plug and call for service.
O
P/No.: 3828ER3021A
LG Electronics Inc.
Download PDF
Similar pages