INSTALLATION MANUAL FOR EC200WH-A13BB-GU-2RC AND EC200WH-A13BB-GU-4RC
PICTOGRAM EXIT SIGN AND EMERGENCY LIGHT COMBO
SAVE THESE INSTRUCTIONS - READ ALL INSTRUCTIONS CAREFULLY
IMPORTANT SAFEGUARDS
WIRING DIAGRAM - FIGURE #1
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Review the diagrams thoroughly before beginning.
• All electrical connections must be in accordance with local codes, ordinances and the National Electric Code.
• Disconnect power at fuse or circuit breaker before installing or servicing.
• Do not use outdoors.
• Do not mount in hazardous locations or near gas or electric heaters.
• Do not let power cords touch hot surfaces.
• Equipment should be mounted in locations and at heights where it will not be subject to tampering by
unauthorized personnel.
• The use of accessory equipment is not recommended by the manufacturer.
USE FLEXIBLE CONDUIT ONLY
• Do not use this equipment other than intended use.
• All servicing should be performed by qualified personnel only.
• Allow battery to charge for 24hrs before first use. For two battery models, allow 48hrs hours.
MOUNTING INSTRUCTION
AC WIRING
Connect the white wire to neutral. If using 120V, connect the
black wire to the hot lead. If using 347V, connect the red wire
to the hot lead. Cap unused lead.
ASSEMBLY LAMP HEADS - FIGURE #2
CONNECTING REMOTE HEADS - FIGURE #8
THE FIXTURE IS SUITABLE FOR WALL, SIDE AND CEILING MOUNTING
1. Open front cover and assemble 2pc lamp heads on the frame.
2. Knockout appropriate mount screw hole and cable hole, mount back plate on the wall after feeding
building AC Supply Cable into back plate. (See Fig #3)
3. For ceiling and side mounting purpose, remove the mounting hole cover on the top or side of unit,
assemble the canopy. (See Fig #4, #5, #6)
4. Attach crossbar to junction box, set the longer blade of crossbar touching the J-Box.
5. Route the proper wires through mounting hole out of housing.
6. Make electrical connections inside the J-Box use the wiring diagram.
7. Push excess wire into J-Box, use screws to tighten canopy to crossbar so canopy is securely fastened
and tight against the wall.
8. Attach battery connector to PC Board, restore front cover on unit, adjust position of lamp heads
as needed.
9. If pictogram direction assembled is not suitable, change pictogram direction or replace pictogram
and then insert into diffuser. (See Fig #7)
WALL MOUNTING - FIGURE #3
LAMP HEAD (FORWARD)
LAMP HEAD (BACKWARD)
1. Open front cover by flat screwdriver.
2. Insert the lamp heads at the corners of the main
frame. Select direction of lamp head before inserting.
3. Connect male connector on lamp head to female
connector on PCBA.
SIDE MOUNTING - FIGURE #4
CANOPY ASSEMBLY - FIGURE #6
USING 1PC BATTERY - NO REMOTE CAPABILITY
USING 2PC BATTERY - REMOTE CAPABILITY
Connect remote heads extension wire to remote wire,
yellow is positive(+), purple is negative (-). Connect
wires using wire nuts.
Remote capability reference below:
EC200WH-A13BB-GU-2RC has max 3.6V 2W remote capability
EC200WH-A13BB-GU-4RC has max 3.6V 4W remote capability
CEILING MOUNTING - FIGURE #5
CHANGE DIRECTION OF PICTOGRAM - FIGURE #7
Insert canopy into housing at 20 degree angle and twist.
Quick snap is now firmly locked.
CAUTION
Trying to remove canopy locked in place may cause damage.
Head Office - 1850 Wilson Ave. · Toronto, ON · M9M 1A1 · Tel: 416.741.7336 · Fax: 416.741.9104 ·
Toll Free: in Canada. 1.800.661.9610 · in USA. 1.888.762.5384 (SOCKETS4U)
www.etlin-daniels.com· For sales/service questions - sales@etlin.com
Download PDF
Similar pages