Roof Accessories Catalog Including Roof Hatches &

Roof Accessories
Division 07 72 33
Roof Hatches
Roof Safety Rails
Safety Posts
Division 07 72 36
Smoke Vents
www.activar.com
Construction Products Group
ROOF HATCH: Galvanized Steel or Aluminum RHG & RHA Series
Certifications: RHG (galvanized) models include components or materials that are
ASTM certified under Specifications A792/A792M-06a; A653/A653M-06a; C726-05;
and A36/A36M-05. RHA (aluminum) models include components or materials that are
ASTM certified under Specifications 209-06 and C726-05.
Load/Deflection:Both steel and aluminum roof hatch covers have been tested and
approved to support a minimum live load of 40 lbs./ft.2 with a maximum deflection of
1/150th of the span, maximum negative load of 50 lbs./ft.2 wind uplift, and 110 mph
wind load when cover is in an open position.
Insulation: The curb includes a 1" fiberboard insulation surrounding the base, and 1"
mineral wool insulation between the exterior cover and liner.
construction: RHG: 14 gauge galvanneal steel with 12" high curb and 3 5/8" wide
flange for securing to roof deck. The cover includes a 14 gauge galvannea lsteel exterior
and 22 gauge liner with with a TPE draft seal gasket door seal. RHA: .090 aluminum with
12" high curb and 3 5/8" wide flange for securing to roof deck. The cover includes
a .090 aluminum exterior and .040 aluminum liner with a TPE draft seal gasket door seal.
Hardware: Hardware includes a heavy duty hinge, slam latch, heavy gauge automatic
hold open arm with red grip, compression spring-operated cylinder, exterior handle
with integral padlock hasp, and interior locking handle with interior padlock hasp.
Finish: RHG: Grey hammertone powder coat. RHA: Bronze powder coat.
Sizes: Minimum 24" x 24", maximum 96" x 48"
Options: Saf-T-Hatch Safety Railing, Polyiso Insulation, Gravity-operated
battery-powered flashing warning light, LP-4,5 or 6 ladder post.
Model
Opening Size
Weight
Model
Opening Size
Weight
RHA-1
30" x 36"
90 lbs.
RHG-1
30" x 36"
150 lbs.
RHA-2
54" x 30"
115 lbs.
RHG-2
54" x 30"
210 lbs.
RHA-3
96" x 30"
190 lbs.
RHG-3
96" x 30"
315 lbs.
RHA-4
36" x 36"
110 lbs.
RHG-4
36" x 36"
185 lbs.
RHA-5
48" x 48"
160 lbs.
RHG-5
48" x 48"
260 lbs.
Custom Sizes Available Upon Request
1" MINERAL WOOL INSULATION
Custom Sizes Available Upon Request
COMPRESSION CYLINDER
.090 ALUMINUM
TPE CONTINUOUS HATCH SEAL
1" fiberboard
insulation
RHA
.040 ALUMINUM
.090 Aluminum
RED VINYL GRIP
ROOFING BY OTHERS
12"
(305mm)
Width
1" MINERAL WOOL INSULATION
COMPRESSION CYLINDER
14 ga. GALVANIZED STEEL
TPE CONTINUOUS HATCH SEAL
1" fiberboard
insulation
RHG
14 ga. (1.9mm)
GALVANIZED STEEL
22 ga. GALVANIZED STEEL
RED VINYL GRIP
ROOFING BY OTHERS
Width
SuBMITTALS AVAILABLE AT: WWW.ACTIVARCPG.COM/JL-INDUSTRIES.COM
12"
(305mm)
RETROFIT GALVANIZED ROOF HATCH: RHR Series
Load/Deflection: Roof hatch cover has been tested and approved to support a
minimum live load or 40 lbs/ft² with a maximum deflection of 1/150th of the span.
Insulation: The curb includes 1” x 11” pine board surrounding the base. The cover
has 1” mineral wool insulation in the space between the exterior cover and liner.
certifications: The RHR includes components or materials that are ASTM certified
under Specifications A792/A792M-06a; A653/A653M-06a; C726-05; and A36/
A36M-05.
Construction: Hatch is 16 gauge galvanized steel with 12” high curb and 3-5/8”
wide flange for securing to roof deck. The cover in-cludes a 16 gauge galvanized steel
exterior and 22 gauge liner with an EPdM gasket door seal.
Hardware: Hardware includes a heavy-duty hinge, heavy-gauge automatic holdopen arm with red grip, compression spring-operated cylinders, rubber-coated
exterior handle with integral padlock hasp and interior latching handle with padlock
hasp.
RHR-1
Finish: Bonderite™ red powder coat.
Options: Gravity-operated battery-powered flashing warning light, Saf-T-Hatch
safety rail.
Model
Opening Size
Weight
RHR-1
30” x 36”
137 lbs.
Custom Sizes Available Upon Request
• Economical Roof Hatch Replacement
• Bonderite™ Pre-Treated Red Hammertone powder coat
• 16 Gauge Galvanized Steel Construction
• No Painting Necessary
• RHG Series Features & Hardware
• Ready for Installation
• Meets Industry Test Standards
• Custom Sizes Available
SaF-T-HaTcH RooFToP SaFeTY RailinG FoR new
& eXiSTinG HaTcHeS: SHWC Series
(Patented Saf-T-Hatch Railing)
certifications: Meets OSHA required compliance for safe egress and ingress
through rooftop hatch openings while hatch is in use. Complies with OSHA CfR 291910.232 and CfR 29-1910.27.
construction: Rail: 1.66" Od galvannealed steel tubing with plastic post caps. The
base is galvannealed 2" x 2" 16 gauge steel tubes and tubing. Tubing base pad is
3/4"styrofoam. Hardware includes threaded rods, caps, nuts and washers.
Guard: Zinc-plated 3/16" ASTM chain with quick links and hoops.
Finish: Safety Yellow Powder Coating.
installation: Quickly installs by a clamping frame around curb base of roof hatch
or fire hatch. does not require “approved” installer. fits all brands of existing roof
hatches with cap flashing—field adjustable up to 4" to fit curb flashing size.
options: Self-closing, rigid steel gate painted safety yellow, SHG-2436 fits hatch
Models 1-5 and weighs approximately (20 lbs). See page 8 for more information.
SHWC-3036 Safety Railing with Standard Chain
SHG-2436
Optional Steel Gate
Model
Opening Size
Weight
Fits Roof Hatch Model
SHWC-3036
30" x 36"
66 lbs.
RHA/RHG/RHR-1
SHWC-3054
54" x 30"
70 lbs.
RHA/RHG-2
SHWC-3096
96" x 30"
80 lbs.
RHA/RHG-3
SHWC-3636
36" x 36"
68 lbs.
RHA/RHG-4
SHWC-4848
48" x 48"
75 lbs.
RHA/RHG-5
Custom Sizes Available Upon Request
SuBMITTALS AVAILABLE AT: WWW.ACTIVARCPG.COM/JL-INDUSTRIES.COM
SAF-T-HATCH RAIL SYSTEM: RHG-STH Series
JL RHG Series Roof Hatch with Safety Rail
SAFETY RAIL: Model STH
Certifications:Rail meets OSHA-required compliance for safe egress and ingress
through rooftop hatch openings while hatch is in use. Complies with OSHA CFR 291910.232 and CFR 29-1910.27.
Construction: Rail is 1.66” Od galvannealed steel with with plastic post caps. Rail
support brackets are welded to the curb. Posts are mechanically-secured to the
brackets.
Hardware: Safety chain is zinc-plated 3/16” ASTM chain with quick links and
hoops.
Finish: Durable Safety Yellow powder coat finish.
Options: Rigid galvanized self-closing gate. Gravity-operated Roof Hatch "Open"
warning light.
GALVANIZED ROOF HATCH: Model RHG
RHG-1-STH
Certifications: RHG models include components or materials that are ASTM
certified under Specifications A792/A792M-06a; A653/A653M-06a; C726-05 and
A36/A36M-05)
Load/Deflection: Roof hatch cover has been tested and approved to support a
minimum live load or 40 lbs/ft² with a maximum deflection of 1/150th of the span,
maximum negative load of 50 lbs/ft² wind uplift, and 110 mph wind load when cover
is in upright position.
Insulation: The curb includes 1” fiberboard insulation surrounding the base. The
cover has 1” fiberglass insulation in the space be-tween the exterior cover and liner.
• Integral Roof Access Safety System
• OSHA-Compliant for Rooftop Safety
• 4 Standard Sizes - Custom Sizes Available
• Durable, Powder Coat Factory Finish
Construction: Hatch is 14 gauge galvanized steel with 12” high curb and 3 5/8”
wide flange for securing to roof deck. The cover in-cludes a 14 gauge galvanized steel
exterior and 22 gauge liner with an EPDM gasket door seal.
Hardware: Hardware includes a heavy-duty hinge, heavy-gauge automatic holdopen arm with red grip, compression-operated shock-absorbing cylinders, exterior
handle with integral padlock hasp and interior latching handle with padlock hasp.
Pre-installed bolts on the counter flashing assist in retaining the membrane materials
against the curb.
Finish: Hatch - Bonderite™ pre-treated gray hammertone powder coat.
• No Painting Required - Installation Ready
Sizes: Minimum 24" x 24", maximum 96" x 48"
• Safety Rail Assembles Easily in Minutes
Options: Gravity-operated battery-powered flashing warning light.
• Assembly Tools & Hardware Included
• Roof Hatch with Railing Sold as One Unit
Model
Opening Size
Weight
RHG-1-STH
30” x 36”
183 lbs.
• Optional Gate & “Open Hatch” Warning Light
RHG-2-STH
54" x 30"
245 lbs.
RHG-4-STH
36" x 36"
219 lbs.
48" x 48"
298 lbs.
• Factory-installed Mounting Brackets
RHG-5-STH
Custom Sizes Available Upon Request
SuBMITTALS AVAILABLE AT: WWW.ACTIVARCPG.COM/JL-INDUSTRIES.COM
DOUBLE LEAF SMOKE VEN UFV Series
UL-Listed
FM Listed.
Approved
certifications: UL
Theand
smoke vents are equipped with a UL listed 165º f
fusible link for automatic operation.
Snow/Wind Load: cover shall open against 10 psf (49 kg/psm) snow/wind load
Live Load: rated for 40 psf (195 kg/psm) live load
Wind Uplift: covers will remain closed under 90 psf (438 kg/psm) wind uplift force
Construction: Covers are 11 gauge aluminum insulated with fiberglass, 14 gauge
galvanized steel curb and curb frame fully welded and ground smooth, gasketed and
insulated for weather tightness.
Operation: Torsion spring drives open the covers automatically. Shock absorbers
control the speed of the leaves as they open. The fusible link can be quickly and
easily replaced.
Hardware: Heavy gauge aluminum 3/16" pivot hinges. Pull handles are provided for
exterior or interior manual operation.
Finish: 2 coats of factory-applied primer.
COVER - 11 GA. ALUMINUM
REINFORCING CHANNEL
COVER LINER 24 GA. GALV. STEEL
COVER FRAME 14 GA.
GALV. STEEL
CONTINUOUS BULB GASKET
WHEEL GUIDE WITH
SAFETY CABLE
3/16" FORMED PIVOT
HINGE
WITH 3/8"
CADMIUM
SHOULDER
PIVOT BOLT
1'-4"
STEEL ROLLER WHEEL
CENTER GUTTER 14 GA.
GALV. STEEL
3/8" CHROME VANADIUM
TORSION SPRING
4"
CURB FRAME
14 GA. GALV. STEEL
FULLY ENCLOSED AUTOMATIC
PULL RELEASE LATCH UNIT
SHOCK ABSORBER WITH HOLD
OPEN ARM - RED VINYL GRIP
INSIDE DIMENSION REQUIRED
4"
SECURING BY OTHERS
Clear O pening Size
UL-Listed
48" x 48"
48" x 72"
48" x 90"
48" x 96"
60" x 60"
60" x 96"
UFV-1
UFV-2
UFV-3
UFV-4
UFV-5
UFV-6
60" x 120"
60" x 144" 66" x 144" 72" x 72"
F
Custom Sizes Available Upon Request • Fusible Links with Higher Temperature UL-Listings Available Upon Reqest
DouBle leaF DomeD SmoKe VenT: UDFV Series
Certifications:
M Approved. The
F smoke vents are equipped with a UL listed 165º
fusible link for automatic operation.
Construction: Dome frame is a minimum thickness of .072 aluminum and provides
a self-contained sloping condensation and weepage gutter for drainage. Covers are
one-piece acrylic dome (either white translucent or clear). The 14 gauge galvanized
steel dome retaining frame is secured to the 14 gauge galvanized steel curb frame.
The galvanized steel curb and curb frame are fully welded and ground smooth,
gasketed and, insulated for weather tightness.
Operation: Torsion spring drives open the covers automatically. Shock absorbers
control the speed of the leaves as they open. The fusible link can be quickly and easily
reset and a new link inserted.
Hardware: Heavy gauge aluminum 3/16" pivot hinges. Pull handles are provided for
exterior or interior manual operation.
Finish: 2 coats of factory-applied primer.
ACRYLIC DOME
GASKET - 8’ O.C.
14 GA. GALV. STEEL CENTER GUTTER
6063 - T5 EXTRUDED ALUM.
RETAINING CAP
SKYLIGHT FRAME .055 6063 - T5
EXTRUDED ALUM.
11GA. ALUM. COVER
3/8” FORMED PIVOT HINGE
WITH CADMIUM SHOULDER
PIVOT BOLT
14 GA. GALV. STEEL
COVER FRAME
14 GA. GALV. STEEL
CURB FRAME
SHOCK ABSORBER &
RED VINYL GRIP HOLD
OPEN ARM
WHEEL GUIDE &
SAFETY CABLE
FULLY ENCLOSED AUTOMATIC PULL
RELEASE LATCH UNIT
CLEAR OPENING NO REQ’D
4"
SECURING BY OTHERS
3/8” CHROME VANADIUM
TORSION SPRING
4"
Clear Opening Size
48" x 48"
48" x 72"
48" x 90"
48" x 96"
60" x 60"
60" x 96"
Model #
UDFV-1
UDFV-2
UDFV-3
UDFV-4
UDFV-5
UDFV-6
Custom Sizes Available Upon Request • Fusible Links with Higher Temperature UL-Listings Available Upon Reqest
Page Revised 2/1/11 OLL 1-800-554-6077 or visit www.jlindustries.com
EQUIPMENT HATCH: EHA & EHG Series
Insulation: The lid has 1” fiberglass insulation in the space between the
exterior cover and liner.
continuous bulb-neoprene door seal. Oversize doors may be spliced.
Hardware: Hardware includes heavy-duty galvanized hinges, pressure
intensifiers, hold-open arms with red vinyl handlegrip . for models 7’ or
larger - adjustable torsion spring automatic hold-open is provided. Lid
hardware has a 2 point universal spring latch, and exterior and interior
handles with integral padlock.
Construction: Hatch is 14 gauge galvanized steel (EHG) or .090 aluminum
(EHA) fully welded and ground smooth for weather tightness. Includes 12”
high curb and 4” wide flange for securing to roof deck. The cover includes a
14 gauge galvanized steel or .090 aluminum exterior and metal liner with a
Finish: 2 coats prime coat.
Options: White dome, Clear dome. (RHWL) Gravity-operated batterypowered flashing warning light. Custom Sizes & finishes Available Consult factory.
Clear Opening Size
72" X 96"
60" X 120"
120" X 120"
144" X 144"
Aluminum
EHA-1
EHA-2
EHA-3
EHA-4
Galvanized
EHG-1
EHG-2
EHG-3
EHG-4
Custom Sizes Available Upon Request
DOMED EQUIPMENT HATCHES - DEHG & DEHA Series
Insulation: The lid has 1” fiberglass insulation in the space between the
exterior cover and liner.
translucent or clear colorless acrylic, a dome frame of extruded aluminum
#6063-T5 with minimum thickness of .070 provided with a self-contained
sloping condensation and weepage gutter for drainage. Lid construction is
galvanized steel or aluminum exterior with metal liner and continuous bulb
gasket door seal. Oversize doors may be spliced.
Construction: Curb and curb frame are 14 gauge galvanized steel or
.090 aluminum, fully welded and ground smooth for weather tightness.
Includes 12” high curb with rigid insulation and 4” wide flange for securing
to roof deck. The lid includes a one piece dome (or multiples) of either white
Hardware: Hardware includes heavy-duty galvanized hinges, pressure
intensifiers, hold-open arms with red vinyl handlegrip . For models 7’ or
larger - adjustable torsion spring automatic hold-open is provided. Lid
hardware has a 2 point universal spring latch, and exterior and interior
handles with integral padlock.
Finish: 2 coats prime coat.
Options: White dome, Clear dome. (RHWL) Gravity-operated batterypowered flashing warning light. Custom Sizes & finishes Available Consult Manufacturer.
Clear Opening Size
72" X 96"
60" X 120"
120" X 120"
144" X 144"
Aluminum
DEHG-1
DEHG-2
DEHG-3
DEHG-4
DEHA-1
DEHA-2
DEHA-3
DEHA-4
Galvanized
Custom Sizes Available Upon Request
SuBMITTALS AVAILABLE AT: WWW.ACTIVARCPG.COM/JL-INDUSTRIES.COM
ROOF HATCH
ROOF HATCH
SAFETY POST SIDE ELEVATION
SAFETY POST SIDE ELEVATION
21 7/8˝
7˝ (WALL)
18 3/8˝
12˝
TOP OF DECKING
CURB
(VERIFY)
7˝ (WALL)
CURB
(VERIFY)
8˝
12˝
SAFETY POST—EXTENDABLE: LP-4 & LP-5
8˝
TOP OF DECKING
The LP-4 Safety Post provides a convenient and
safe method of climbing off and onto fixed
NOTE: INTERMEDIATE BRACKET
REQUIRED WHEN LADDER
access ladders.
HEIGHT IS 10´-0˝ OR MORE
NOTE: INTERMEDIATE BRACKET
REQUIRED WHEN LADDER
HEIGHT IS 10´-0˝ OR MORE
2˝ X 5/16˝ TYP
ALUMINUM WALL
TOP BRACKET
(VERIFY FIELD DIMENSION)
(VERIFY FIELD DIMENSION)
OVERALL LADDER HEIGHT
BRACKET
EQUAL SPACES AT 12˝ O.C.
EQUAL SPACES AT 12˝ O.C.
2˝ X 5/16˝ TYP
Installation: The
LP-4
comes
pre-assembled and attaches directly to the
7/16˝ HOLES
FOR
ALUMINUM
WALL Safety Post
3/8˝ Ø ANCHOR BOLTS
TOP BRACKET
2˝ X 5/16˝ TYP
(BY OTHERS)
ALUMINUM
WALL
7/16˝ HOLES FOR
5’-0”
top two rungs (square
or
round)
with
two
U-shaped
bolts.
INTERMEDIATE
3/8˝ Ø ANCHOR BOLTS
2˝ X 5/16˝ ALUMINUM FLAT
2˝ X 5/16˝ TYP
(BY OTHERS)
BAR WALL BRACKET (SEE
ALUMINUM WALL
5’-0”
ELEVATION FOR LOCATION)
INTERMEDIATE
2˝ X 5/16˝
ALUMINUM
FLAT The spring coil allows
safety
post.
Ease of Use: When
BRACKET at the top of the ladder, extend the
BAR WALL BRACKET (SEE
RUNG, STAINLESS
ELEVATION FOR LOCATION)
TYP
ALUMINUM
STEEL
FASTENERS
ATin a safe standing position while
user to lift withSERRATED
just
one hand.
Step on or off1/4˝
the
ladder
7˝
BRACKETS
1/4˝ RUNG, STAINLESS
RUNGS 1 1/4˝
STEELand
FASTENERS AT
#12
holding onto the post. A latch maintains the post
at STAINLESS
variable heights
7˝ X 1 1/4˝
BRACKETS is easily released
STEEL HEX HEAD TAPING
SCREWS
#12 X 1 1/4˝ STAINLESS
for retracting the post.
STEEL HEX HEAD TAPING
TYP ALUMINUM
SERRATED
RUNGS 1 1/4˝
SCREWS
1 1/4˝ SQ. EXTRUDED
RUNG 6065-TS
Safety Features: Square posts for
a no-slip grip We1 1/4˝recommend
a Saf-T-Hatch
HL-1 EXTRACTED
SQ. EXTRUDED
ALUMINUM CHANNEL
RUNG 6065-TS
RAIL 6065-TS
4˝ X 2˝ X 5/16˝
HL-1 EXTRACTED
rail system in addition
to the LP-6 Safety
Post for greater
safety.
ALUMINUM ANGLE
ALUMINUM
CHANNEL
HL-2 EXTRUDED
STANDARD FLOOR
RAIL 6065-TS
ALUMINUM COVER
PLATE 6065-TS
HL-2 EXTRUDED
25ELEVATION
lbsBRACKET
Weight:SIDE
ALUMINUM
COVER
TOP LADDER DETAIL
4˝ X 2˝ X 5/16˝
ALUMINUM ANGLE
STANDARD FLOOR
BRACKET
FRONT ELEVATION
0˝
PLATE 6065-TS
FRONTLP4:
ELEVATION
SIDE ELEVATION
Finish
Safety Yellow Powder
Coat
TOP LADDER DETAIL
Finish LP5: Hot-Dip Galvanized
5´-0˝
CONSTANT FORCE
SPRING
16˝
3/8˝ X 1.80˝
SLOT
A375 Ø
U-CLIP
3/8˝ X 1.80˝
SLOT
SQ. HOLE
.80˝
SQ. HOLE
4.00˝
4.125˝
LOCK NUT
& WASHER
13˝ SQ. TUBE
R 13˝
SHOP WELD
BOTH SIDES
SQ. HOLE
1/4˝ STL.
CLAMPING
PLATE
3/8˝ ALUM.
S.125˝ Ø
U-BOLT
1/4˝ STAINLESS STL.
2.25˝
2.25˝
.875˝
2.375˝
3.5˝
SLOPE
3/8˝ Ø BOLT & NUTS
.875˝
4X • .375˝
1.00˝
1.50˝
SQ. TUBE
1.5625˝
SQ. HOLE
1.5˝ SQ. TUBE
CLAMPING
PLATE
8 1/4˝ IN DOWN POSITION
45˝ IN UP POSITION
12˝
RUNG
RUNG
EZ-UP LP-6 LADDER POST
The EZ-up LP-6 Ladder Post provides easy and safe access through a roof hatch.
The assambly permanently mounts to hte roof hatch and acts as an extension to the
ladder to enable users to safely enter and exit a roof access hatch.
Installation: Mounts to top of curb with six self-tapping screws.
Ease of Use: After the user opens the roof hatch, the post is raised with one hand
and self-locks into an upright position. The user can then climb from the ladder
the rooftop using the post for a handhold. The post can easily be folded down into
the stowed position.
Safety Features: Allows the roof hatch to be closed while user is on the roof. We
recommend a Saf-T-Hatch rail system in addition to the LP-6 Safety Post for greater
safety.
Weight: 8 lbs
Finish : Safety Yellow Powder Coat
SuBMITTALS AVAILABLE AT: WWW.ACTIVARCPG.COM/JL-INDUSTRIES.COM
OPTIONAL l GaTe FoR SaF-T-HaTcH RailinGS: SHG - 2436
Increase rooftop safety with a self-closing, rigid galvanized steel gate with spring hinge for
JL’s Saf-T-Hatch railings. This adjustable gate fits both stand-alone SHWC and integrated
RHG-STH models. Safety yellow painted.
Gate
SHG-2436
Fits Safety Railing
Weight
Models up to 36" Opening
17 lbs.
Custom Sizes Available Upon Request
Gate Shown in
Contracted and
Expanded Positions
ROOF HATCH WARNING LIGHT – RHWL
The warning light is designed to alert personnel that the roof top opening or hatch is in the
open position. A very bright, red, xenon strobe light emitting 60 double flashes per minute is
activated as soon as the hatch is lifted upward 30 degrees. The strobe automatically turns
“Off” when the hatch is in the closed position. Installation & Operation: Mounted on the inside
surface of the hatch with its magnetic base, the Model RHM-2P-R-S features a built-in tilt
switch that is located in its battery compartment. This switch automatically triggers the strobe
to its flashing mode when the hatch is lifted upward. Two (2) new D-Cell alkaline batteries
provide 50-60 flashing hours. The “Hatch Alert” is not intended to replace roof top safety
initiatives or Saf-T-Hatch rail systems but rather to be used in conjunction with them. The
flashing signal is an additional alert that the hatch is open.
WARRANTY—All products carry a one year warranty after date of shipment against defects in materials and workmanship. We will replace or repair any
product found defective within this period at our discretion. No other warranty express or implied is valid.
Manufacturing/Warehousing Locations
ACPG FARGO
WAREHOUSE


s
RENTON, WASHINGTON
9702 NEWTON AV S, BLOOMINGTON, MN 55435
Lancaster, Pennsylvania
ACPG OMAHA
WAREHOUSE

Atlanta, Georgia
Grand Prairie, Texas
CommerCe, Ca 90040
FORT MYERS, FL 33905
800-554-6077
E-MAIL: SALES@ACTIVARCPG.COM
WEB SITE: WWW.ACTIVARCPG.COM/JL-INDUSTRIES
The activar construction Products Group (acPG) consists of 6 affiliated companies that serve the commercial construction industry. Our multiple product lines are a single source for architects and
distributors. Air Louvers manufactures products for the openings market with door lites, louvers and rated-glass. Hiawatha is known for its quality architectural door hardware and frameless shower door products.
JL Industries is an industry leader in fire protection, providing fire extinguishers, AEDs and cabinets, access panels, roof opening products and entrance flooring systems. Samson Products manufactures many
of the products sold under the JL label and distributes JL products on the West Coast. Thomas Enterprises is our Southeast distributor for JL products and has a state-of-the-art aluminum fabrication facility for
fire extinguisher cabinets sold under the Thomas and JL labels. Rooftop Accessories provides a line of roof support systems. We can now ship from 10 US locations.
© 2017 Activar Construction Products Group, Inc.
SuBMITTALS AVAILABLE AT: WWW.ACTIVARCPG.COM/JL-INDUSTRIES.COM
RA0909 REV K
Download PDF
Similar pages