2018
TITAN
QUICK REFERENCE GUIDE
5
4
16
3
2
17
1
9
7
8
10 11
25
18
20
19
6
12 13 14
15
Beneath the
instrument panel
1 Headlight Control Switch
2
3
4
5
6
7
Turn Signal/Wiper and
Washer Switch
Vehicle Information Display
Low Tire Pressure Warning Light/
DEF Warning Light
Tow Mode Switch*
Tilt/Telescopic Steering Column*
Cruise Control
*See your Owner’s Manual for information.
21
Behind the
steering
wheel
Steering Wheel Switches for
8 Audio*/Bluetooth®/Siri® Eyes
Free/Vehicle Information Display
9 Fog Light Switch
10 Power Inverter Switch
11 Cargo Lamp Switch*
12 Headlight Aiming Control*
22
26
23
24
14 Hill Descent Control Switch
15 Hood Release
16 Audio and Navigation System
Heater and Air Conditioner
(automatic)
Vehicle Dynamic Control (VDC)
18
OFF Switch*
E
lectronic
Locking
Rear
Differential
Parking Sensor System
13 19 (E-Lock) System Switch*
Off Switch*
17 20Warning Systems Switch
21 4WD Switch*
22 Trailer Brake Controller Unit
23 USB Port/Aux Jack
24 Climate-Controlled Seat Switches*
Front Passenger Air Bag
Status Light*
26 12V Power Outlets
25
TABLE OF CONTENTS
NEW SYSTEM FEATURES
NissanConnect® Services Powered by SiriusXM® (if so equipped) . . . . . . . . . . . . . . . . . . . . 2
Intelligent Around View Monitor (I-AVM) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Hill Start Assist and Hill Descent Control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Blind Spot Warning (BSW) with Rear Cross Traffic Alert (RCTA) (if so equipped) . . . . . . 6
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Diesel Exhaust Fluid (DEF) (diesel models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Diesel Particulate Filter (DPF) (diesel models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Siri® Eyes Free (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SiriusXM Travel Link and SiriusXM Traffic (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ESSENTIAL INFORMATION
Passenger Seat Belt Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Tire Pressure Monitoring System (TPMS) with Easy-Fill Tire Alert . . . . . . . . . . . . . . . . . . . . . 11
Clock Set/Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Loose Fuel Cap (gas engine models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Fuel-filler Door and Diesel Exhaust Fluid (DEF) Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Wide Open Door (King Cab® models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
FIRST DRIVE FEATURES
Nissan Intelligent Key® System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Opening the Tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power Seat Adjustments (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Rear Seats (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Outside Mirror Control Switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Automatic Drive Positioner (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Headlight Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Wiper and Washer Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Starting/Stopping the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Heater and Air Conditioner (automatic) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
USB (Universal Serial Bus) Connection Port/Aux Jack and iPod® Interface . . . . . . . . . . 22
FM/AM/SiriusXM® Satellite Radio with CD Player (if so equipped) . . . . . . . . . . . . . . . . . . . 23
Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SYSTEM GUIDE
Vehicle Information Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Hands-free Text Messaging Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Bluetooth® Hands-free Phone System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
• System Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Bluetooth® System without Navigation (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Bluetooth® System with Navigation (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Nissan Mobile Entertainment System (MES) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . 33
HomeLink® Universal Transceiver (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Additional information about your vehicle is also available in your Owner’s Manual,
NissanConnect® Owner’s Manual and at www.NissanUSA.com.
Please see your Owner’s Manual for important safety information and system operation limitations.
• A cellular telephone should not be used for any purpose while driving
so full attention may be given to vehicle operation.
• Always wear your seat belt.
• Supplemental air bags do not replace proper seat belt usage.
• Children 12 and under should always ride in the rear seat properly secured
in child restraints or seat belts according to their age and weight.
• Do not drink and drive.
For more information, refer to the “Safety — Seats, seat belts and supplemental restraint system (section 1)”,
the “Monitor, climate,
audio,
phoneinstructional
and voice recognition
systems
(section
andfeatures,
the “Starting and driving
To view
detailed
videos regarding
these
and 4)”
other
(section 5)” of your Owner’s Manual.
please go to www.nissanownersinfo.mobi.
iv
NEW SYSTEM FEATURES
NISSANCONNECT® SERVICES POWERED by SiriusXM®
(if so equipped)
issanConnect® Services is a collection of security and convenience services that
N
add innovation to your daily drive.
To enroll in NissanConnect Services, create an account or log into your
Nissan Owner Portal with your Vehicle Identification Number (VIN). Under the
NissanConnect Services tab, select the red button next to Manage Subscription.
Follow the prompts to enroll in NissanConnect Services. Next, download the
NissanConnect Services companion app and log into it using your Nissan Owner
Portal ID and password.
For full details on NissanConnect Services or to enroll your vehicle, please visit
www.NissanUSA.com/connect or call 855-426-6628.
Here is a quick overview of some of the features that may be available for your
vehicle. A full description of these and other NissanConnect Services can be found in
your NissanConnect Owner’s Manual.
Automatic Collision Notification, a service that
generates an automatic connection between
the vehicle and the Emergency Response
Center when the vehicle has been involved
in an accident that was severe enough to
deploy the air bags.
1
Emergency Call, which connects you to a
NissanConnect Services Specialist who will
assist in the dispatch of emergency services to the vehicle’s location. To use this
feature, press the SOS button 1 on the overhead console. The SOS button 1
should only be used in emergency situations.
Roadside Assistance, which dispatches
roadside assistance to the vehicle’s location
in non-emergency situations. Roadside
Assistance can be accessed by touching the
headset icon 2 on the map screen, via
NissanConnect Services Companion app or
by calling the Roadside Assistance
provider directly.
2
Stolen Vehicle Locator, a service that works in
coordination with law enforcement agencies
to assist in the recovery of a stolen vehicle.
Remote Door Lock/Unlock, for use when you forget to lock your car or if
you need to open it and don’t have the keys. To use this feature, log into the
NissanConnect Services companion app or website or contact a NissanConnect
Services Response Specialist.
Remote Engine Start – Start your engine remotely using the NissanConnect
Services companion app or website.
2
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
Assisted Search, a feature that allows you to verbally request point-of-interest
or destination data from a live operator by touching the
headset icon 2 on
the map screen.
Journey Planner, with which you can send a route with a destination and up to
five way points directly to the vehicle.
Boundary Alert, a feature that allows you to monitor the movement of your
vehicle in and out of specified regions you have set on the Monitoring section of
the NissanConnect Services web portal or companion app, and
Speed Alert, which sends you alerts when your vehicle speed exceeds a
threshold you have set on the web portal or companion app.
Alarm Notification – This system will notify you when the factory‐installed
vehicle alarm system has been activated.
Maintenance Alert – Receive notifications via a selected method of a vehicle
system malfunction that triggers instrument panel warning lights.
Connected Search – Select “Connected
Search” from the Destination menu on the
vehicle’s Navigation System to conduct a
Point Of Interest (POI) search within a certain
distance of the vehicle’s location.
Valet Alert – Use Valet Alert to set up a
0.2‐mile radius around your vehicle.
Activate alerts via the NissanConnect
Services companion app or website.
Curfew Alert – Specify curfew limits via the
NissanConnect Services companion app
or website and be notified via a selected
method if curfew is violated.
3
To access these features in your vehicle:
• Press the
panel, then
•T
ouch the “NissanConnect Services” key 4 .
4
button 3 on the control
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Information (section 5)” of your NissanConnect® Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
3
NEW SYSTEM FEATURES
INTELLIGENT AROUND VIEW MONITOR (I-AVM) (if so equipped)
With the ignition switch in the ON position, the Intelligent Around View Monitor is
activated by pressing the CAMERA button
1 , located on the control panel, or by
moving the shift lever to the R (REVERSE)
position. The monitor displays various views
1
of the position of the vehicle.
When the shift lever is in the P (PARK), N
(NEUTRAL) or D (DRIVE) position and the CAMERA button 1 is pressed, the
following views will display in order:
Start from any
Control Panel screen
Front view &
bird’s-eye view
Press
Front view & front-side view
Press
Press
When the shift lever is in the R (REVERSE) position and the CAMERA button 1
is pressed, the following views will display in order:
Rear view & bird’s-eye view
Rear view & front-side view
Press
Rear wide view
Press
Press
The colored guide lines on the display screen indicate vehicle width and
approximate distances to objects with reference to the vehicle body line.
• Red 1.5 ft (0.5 m); Yellow 3 ft (1 m); Green 7 ft (2 m) and 10 ft (3 m).
When the vehicle’s outside mirrors are extended for towing, you may see the
mirrors in the bird’s-eye view or the front-side view.
4
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
For information regarding how to access additional viewing cycles, please see
your Owner’s Manual.
There are some areas where the system will not detect objects.
• When in the front or the rear view display, an object below the bumper or on
the ground may not be detected 2 .
• When in the bird’s-eye view, a tall object near
the seams of the camera detecting areas
3 will not appear in the monitor.
2
• The distance between objects viewed on the
Intelligent Around View Monitor differs from
the actual distance.
Objects in the bird’s-eye view will appear
further than the actual distance.
3
MOVING OBJECT DETECTION (MOD)
(if so equipped)
LHA3807
The MOD system helps inform the driver of moving objects around the vehicle.
The system will operate when the shift lever is in the D (DRIVE), N (NEUTRAL),
R (REVERSE) or P (PARK) position and the
vehicle is driven at speeds of approximately 5
mph (8 km/h) or less.
If the MOD system detects moving objects,
a yellow frame will be displayed on the
camera image.
When the following is displayed:
2A
4
• Blue MOD icon 4 ; the system is active.
• Gray MOD icon; the system is not active.
• No MOD icon; the system is off. The indicator will be off if the system is
deactivated using the Settings menu.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
5
NEW SYSTEM FEATURES
HILL START ASSIST AND HILL DESCENT CONTROL (if so equipped)
HILL START ASSIST
Hill Start Assist allows time for the driver to release the brake pedal and apply the
accelerator when the vehicle is parked on a hill. The brakes are applied automatically
for 2 seconds after the driver releases the brake pedal.
Hill Start Assist will operate automatically under these conditions:
• The shift lever is shifted into a forward or a reverse gear.
• The vehicle is stopped completely on a hill by applying the brake.
Hill Start Assist will not operate when the shift lever is in the N (NEUTRAL) or
P (PARK) position or when the vehicle is on a flat and level road.
HILL DESCENT CONTROL (if so equipped)
Hill Descent Control is designed to apply the brakes to help control the speed of
the vehicle and reduce the workload of the driver while descending steep hills.
To activate the system:
• The Hill Descent Control switch 1 must
be on.
• The vehicle must be in 4H or 4LO
(4WD) mode.
• The shift lever must be in a forward or a
reverse gear.
• Hill Descent Control operates at speeds of 15 mph (25 km/h) or less.
1
To deactivate Hill Descent Control, push the Hill Descent Control switch 1
to the OFF position.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
BLIND SPOT WARNING (BSW) WITH REAR CROSS TRAFFIC
ALERT (RCTA) (if so equipped)
6
The BSW helps to alert the driver when
another vehicle moves into the vehicle’s
detection zone.
1
An indicator light located on the outside
mirrors 1 will illuminate if the radar sensors
detect a vehicle in the detection zone.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
Push the Warning Systems switch 2 to
temporarily turn the system off. When the
system is off, the indicator light 3
on the switch and the indicator light 4 in
the vehicle information display will extinguish.
5
2
6
3
The indicator light 3 on the switch will also be off if all of the
warning systems are deactivated using the Settings menu.
The indicator lights 3 and 4 will illuminate after the
ignition switch is ON and the BSW system is enabled. This
indicates that the BSW system is operational.
The RCTA system helps to alert the driver of an approaching vehicle when
the driver is backing out of a parking space. The system operates when the
shift lever is in the R (REVERSE) position and the vehicle speed is less than
approximately 5 mph (8 km/h).
Push the Parking Sensor (Sonar) System OFF switch 5 to temporarily turn the
RCTA system off. When the system is off, the indicator light 6 on the switch
will extinguish.
The radar sensors detect an approaching vehicle from up to 66 ft (20 m).
The sensors are located on both sides of the vehicle near the rear and front
bumpers. The system gives visual and audible warnings if an approaching
vehicle is detected.
4
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instrument panel (section 2)” and the “Starting and driving
(section 5)” of your Owner’s Manual.
TOWING
TRAILER BRAKE CONTROLLER UNIT (if so equipped)
he Trailer Brake Controller Unit will assist with effective and smooth braking while
T
towing a trailer.
Operating Modes:
• Automatic: Automatic operation of trailer brake pressure based on gain and
boost settings.
• Manual: Manually applies trailer brake pressure without pressing the vehicle’s
brake pedal.
In automatic mode, the gain controls the
amount of trailer braking pressure. To set
the gain:
• Press the
or
button 1 to decrease or
increase the braking force supplied to the
trailer brakes. For example, a gain setting of
6.0 is a typical starting point for heavy loads.
1
2
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
3
7
NEW SYSTEM FEATURES
In automatic mode, the boost can be set to change the feel of the trailer brake
when the vehicle’s brake pedal is pressed. To set the boost:
• Press the
• Press the
button 2 again to increase the boost level or continue to press
the
button 2 to return boost to the off position.
button 2 once to display the current boost setting.
To manually apply brake pressure to the trailer without pushing the vehicle’s
brake pedal, pinch the manual control levers 3 together. The amount of
pinch pressure applied to the levers 3 will correlate to the amount of brake
pressure applied.
TRAILER LIGHT CHECKING (if so equipped)
Your Nissan Intelligent Key® can be used to check
the trailer lights from outside the vehicle. If your
vehicle is equipped with a three-button key fob,
this feature operates in the same manner.
4
1. Aim the Intelligent Key at the vehicle.
2. Press and release the
button 4 .
3.Within 2 seconds, press the button 4
again and hold it until the horn beeps once
and the parking lights turn on.
The trailer light check will follow the following sequence:
• The left turn light on the vehicle and trailer will flash for 5 seconds.
• The right turn light on the vehicle and trailer will flash for 5 seconds.
• The brake lights on the vehicle and trailer will turn on for 5 seconds.
GOOSENECK HITCH (if so equipped)
The integrated gooseneck hitch is located in
the center of the vehicle bed 5 .
5
For installation instructions and towing
information, refer to the “Starting and
driving (section 5)” and the “Technical and
consumer information (section 10)” of your
Owner’s Manual.
Please see your Owner’s Manual for important safety information, system limitations,
and additional operating and feature information.
For more information, refer to the “Instruments and controls (section 2)”, the “Pre-driving checks
and adjustments (section 3)” and the “Technical and consumer information (section 10)” of your
Owner’s Manual.
8
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
DIESEL EXHAUST FLUID (DEF) (diesel models only)
A DEF Low message will appear in the vehicle
information display 1 and the
warning
light 2 will illuminate if the DEF is low and
needs to be topped off.
If the fluid is contaminated, it will need to
be replaced.
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating and
feature information.
1
DEF Low
2
For more information, refer to the “Instrument panel
(section 2)” and the “Fuel and refueling (section 4)” of your
Titan Diesel Owner’s Manual.
DIESEL PARTICULATE FILTER (DPF) (diesel models only)
An Exhaust Filter Overloaded message will
appear in the vehicle information display 1
warning light 2 will illuminate
and the
if the particulate matter has accumulated in
the DPF to the specified limit.
As soon as safely possible, drive the vehicle at
a speed greater than 55 mph (89 km/h) for at
least 45 minutes.
warning light 2 is blinking, refer
If the
to the “Do-it-yourself (section 6)” of your Titan
Diesel Owner’s Manual.
1
Exhaust Filter
Overloaded
2
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating and
feature information.
For more information, refer to the “Instrument panel (section 2)” and the “Do-it-yourself (section 6)” of
your Titan Diesel Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
9
NEW SYSTEM FEATURES
SIRI® EYES FREE (if so equipped)
If you have a compatible iPhone® with
Siri®, you can link your iPhone® to the
Siri® Eyes Free function in your vehicle’s
Bluetooth® system.
If you have a compatible iPhone® connected
button
to the system, press and hold the
1 on the steering wheel for a few seconds
and Siri® will be activated in Eyes Free mode.
1
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual and visit www.NissanUSA.com/bluetooth.
SiriusXM TRAVEL LINK AND SiriusXM TRAFFIC
(if so equipped)
Your vehicle’s Navigation System is equipped
with SiriusXM Travel Link and SiriusXM
Traffic capabilities.
SiriusXM Travel Link provides access to
real-time weather information and forecasts,
nearby fuel prices, movie listings, sports
scores and stock quotes.
SiriusXM Traffic provides information that
may help to avoid delays due to traffic
incidents. Traffic jams, roadwork, road
closures around the current location, etc., are
represented graphically on the map by icons
depicting the nature of the event. Incidents
on the route are automatically displayed as
they are approached.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to your NissanConnect® Owner’s Manual.
10
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
ESSENTIAL INFORMATION
PASSENGER SEAT BELT WARNING
The
warning light 2 will be displayed
in the instrument panel 1 for a period
of time after shifting into drive or until the
passenger’s seat belt is fastened. This does
not indicate a malfunction.
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating and
feature information.
1
2
For more information, refer to the “Safety—Seats, seat belts
and supplemental restraint system (section 1)”, and the
“Instruments and controls (section 2)” of your Owner’s Manual.
TIRE PRESSURE MONITORING SYSTEM (TPMS) WITH EASY-FILL
TIRE ALERT
A Tire Pressure Low - Add Air warning
message will appear in the vehicle
information display 1 and the low tire
pressure warning light 2 will illuminate
when one or more tires are low in pressure
1
and air is needed.
• The tire pressures should be checked when
the tires are cold. The tires are considered
cold after the vehicle has been parked for
3 hours or more or driven less than 1 mi
(1.6 km) at moderate speeds.
After tire pressures are adjusted, drive the vehicle at speeds above
16 mph (25 km/h). The Tire Pressure Low - Add Air warning
2
message and low tire pressure warning light 2 will extinguish.
In addition to the Tire Pressure Low - Add Air warning message,
you can view the individual tire’s pressure in the vehicle information display as
well as the recommended pressure, denoted by blue lettering, for each tire.
When adding air to an under-inflated tire, the TPMS with Easy-Fill Tire Alert
provides visual and audible signals to help you inflate the tire to the
recommended COLD tire pressure.
To use the Easy-Fill Tire Alert:
1. Move the shift lever to the P (PARK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3. Add air to the under-inflated tire, and within a few seconds, the hazard
warning lights will start flashing.
4. When the designated tire pressure is reached, the horn will beep once and the
hazard warning flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
11
ESSENTIAL INFORMATION
When the low tire pressure warning light 2 flashes for 1 minute and then
remains on, the TPMS is not functioning properly. Have the system checked. It is
recommended you visit a Nissan dealer for this service.
Tire pressure rises and falls depending on the heat caused by the vehicle’s
operation and the outside temperature. Low outside temperature can lower
the temperature of the air inside the tire, which can cause a lower tire inflation
pressure. This may cause the low tire pressure warning light 2 to illuminate.
If the warning light illuminates, check the tire pressure in your tires.
• Check the tire pressure (including the spare tire) often and always prior to long
distance trips.
The Tire and Loading Information label contains valuable information. Refer to
the “Technical and consumer information (section 10)” of your Owner’s Manual
for the location of the Tire and Loading Information label.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section
5)”, the “In Case of Emergency (section 6)”, and the “Do-it-yourself (section 8)” of your Owner’s Manual.
CLOCK SET/ADJUSTMENT
WITHOUT NAVIGATION (if so equipped)
1. Press the ENTER/SETTING button 1 to show
the “Settings” screen on the display.
3
2. T
urn the TUNE•SCROLL knob 2 to highlight
“Clock Adjust”.
3. Press the ENTER/SETTING button 1 to
highlight the hours, minutes or AM/PM and use
the TUNE•SCROLL knob 2 to adjust
the value.
2
1
4. Press the ENTER/SETTING button 1 to set the value.
5. Press the
BACK button 3 to return to the previous screen.
WITH NAVIGATION (if so equipped)
To adjust the time and the appearance of the
clock on the display:
1. Press the
button 4 .
2. Touch the “Settings” key.
3. Touch the “System” key.
4. Touch the “Clock/Date” key.
6
4
12
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
The following settings can be adjusted:
• Time Format: The clock can be set to 12 hours or 24 hours.
• Date Format: The date can be changed to one of two different formats.
• Clock Mode: From here, the clock mode options are:
· Manual: Allows for the option “Set Clock/Date Manually”. Touch this to begin
setting the clock manually using the “+” or “–” to adjust the hours, minutes,
day and month up or down.
·T
ime Zone: Touch the “Time Zone” key
5 to choose from the applicable time
zone list and/or touch the “Daylight
Savings Time” key to switch between ON
and OFF.
· Auto: Automatically sets the clock to the
vehicle’s current location.
Press the
5
BACK button 6 to return to the previous screen.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
LOOSE FUEL CAP (gas engine models only)
A LOOSE FUEL CAP warning message will
display in the vehicle information display/
odometer 1 when the fuel-filler cap is not
tightened correctly.
To tighten, turn the cap clockwise until a
single click is heard.
If the cap is not properly tightened, the
Malfunction Indicator Light 2 may
also illuminate in the instrument panel.
2
1
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” and the “Pre-driving checks
and adjustments (section 3)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
13
ESSENTIAL INFORMATION
FUEL-FILLER DOOR AND
DIESEL EXHAUST FLUID (DEF) CAP
The fuel-filler door 1 is located on the
driver’s side of the vehicle.
To open the fuel-filler door 1 , pull the
lid open.
1
DEF CAP (diesel models only)
The DEF cap 2 is located next to the fuel
cap behind the fuel-filler door 1 .
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating and
feature information.
For more information, refer to the “Pre-driving checks and
adjustments (section 3)” of your Owner’s Manual and the “Fuel
and refueling (section 4)” of your Titan Diesel Owner’s Manual.
2
WIDE OPEN DOOR (King Cab® models only)
Do not open the driver’s side Wide Open Door to the fully open position while the
fuel-filler door is open; only open it as far as the first detent.
Opening the door to the fully open position may damage the fuel-filler door and
the Wide Open Door.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
14
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
FIRST DRIVE FEATURES
NISSAN INTELLIGENT KEY® SYSTEM
The Nissan Intelligent Key® system allows you to lock or unlock the vehicle and start
the engine. It is important to make sure the Intelligent Key is with you (that is, in your
pocket or purse).
The operating range of the Intelligent Key is within 31.5 in (80 cm) of the
corresponding request switch.
To lock the vehicle, push either door handle
request switch 1 (if so equipped) or press
the button 2 on the key fob.
To unlock the vehicle, perform one of the
following procedures:
• Push either door handle request switch 1
(if so equipped) once and the corresponding
door will unlock. Push the request switch
1 (if so equipped) again within 5 seconds;
all other doors will unlock, or
1
5
2
• Press the button 3 on the key fob to
unlock the driver’s side door. Press the
button 3 again; all other doors will unlock.
3
4
The Intelligent Key can also be used to
activate the panic alarm by pressing and holding the button 4 for more
than 1 second. Once activated, the panic alarm and headlights will stay on for a
period of time.
INTELLIGENT KEY BATTERY DISCHARGE
If the battery of the Intelligent Key is discharged or environmental conditions
interfere with the Intelligent Key operation, start the engine according to the
following procedure:
1. Move the shift lever to the P (PARK) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key, and a chime will sound.
4. Within 10 seconds after the chime sounds, push the ignition switch to the ON
position while depressing the brake pedal and the engine will start.
REMOTE ENGINE START* (if so equipped)
The remote start operating range is approximately 200 ft (60 m) from the
vehicle. The effective operating range may be shorter if there are walls, strong
radio wave sources near the operating location or other obstructions between
the key and the vehicle.
For the remote start to function, the vehicle must be in the P (PARK) position
with the ignition off and all of the doors must be closed and locked. Please see
your Owner’s Manual for additional information.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
15
FIRST DRIVE FEATURES
To start your vehicle remotely:
1. Press the button 2 to lock all of the doors.
2. Within 5 seconds, press and hold the engine start
least 2 seconds.
button 5 for at
The engine will start, and the parking lights will turn on.
While the remote start feature is being used, the manual or automatic climate
control system will default to the last used heating or cooling mode.
The engine will run for 10 minutes and then turn off.
Repeat steps 1 through 2 to extend the time for an additional 10-minute period.
Remote start can only be activated for a maximum of 20 minutes.
• After two remote starts, the ignition switch must be cycled before the remote
start can be used again.
• To cancel remote start, press the engine start
button 5 .
To start driving, depress the brake pedal and push the ignition switch to the
ON position.
*State laws may apply; review local laws before using.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and
driving (section 5)” and the “Do-it-yourself (section 8)” of your Owner’s Manual.
OPENING THE TAILGATE
Pull the tailgate handle 1 upward and
lower the tailgate. Support cables hold the
tailgate open.
1
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating and
feature information.
For more information, refer to the “Pre-driving checks and
adjustments (section 3)” of your Owner’s Manual.
POWER SEAT ADJUSTMENTS (if so equipped)
To slide the seat forward or backward, push the switch 1 forward or backward.
To adjust the angle of the seatback, push the switch 2 forward or backward.
SEAT LIFTER (driver’s seat)
To adjust the angle and height of the seat
cushion, push the front or rear end of the
switch 1 up or down.
POWER LUMBAR SUPPORT (driver’s seat)
1
2
3
To adjust the lumbar area, push the front or back end of the switch 3 .
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Safety — Seats, seat belts and supplemental restraint system
(section 1)” of your Owner’s Manual.
16
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
REAR SEATS (if so equipped)
To access the under seat storage (if
so equipped):
• Pull up the bottom of the seat toward the
rear of the vehicle to fold the seat.
• Lift the flat floor panels 1 toward the seat.
When not in use, the storage bin’s cover may
be locked.
To use the flat floor feature (if so equipped):
• Pull up the bottom of the seat toward the
rear of the vehicle to fold the seat.
• Pull the handle 2 of the smaller top panel
toward the rear of the vehicle.
• Pull the flat floor panels 3 up and toward
the front seats to fully unfold them and
place them on the floor.
Up to 247 lbs (112 kg) of cargo can be
attached to the flat floor panels using
bungee cords. Only use bungee cords rated
at the appropriate strength.
1
2
3
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating and
feature information.
For more information, refer to the “Instruments and controls
(section 2)” of your Owner’s Manual.
OUTSIDE MIRROR CONTROL SWITCH (if so equipped)
The outside mirror control switch is located
on the driver’s side door panel.
To select the left or right mirror, turn the knob
1 to select the desired mirror.
Adjust each mirror to the desired position by
pushing the side of the knob 1 up, down,
left, or right.
1
2
REVERSE TILT-DOWN FEATURE (if so equipped)
The reverse tilt-down feature will turn both outside mirror surfaces downward
to provide better rear visibility close to the vehicle.
1. Apply the brake.
2. Place the ignition switch in the ON position.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
17
FIRST DRIVE FEATURES
3. Move the shift lever to the R (REVERSE) position.
4. Both outside mirror surfaces will turn downward. (The mirror control switch
1 must be out of the center [neutral] position.)
The outside mirror surfaces will return to their original positions when one of
the following conditions occurs:
• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch 1 is set to the center (neutral) position.
• The ignition switch is placed in the OFF position.
POWER FOLDING OUTSIDE MIRRORS (if so equipped)
To open or close the mirrors, push the switch 2 .
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
AUTOMATIC DRIVE POSITIONER (if so equipped)
Two positions for the driver’s seat, steering
column and outside mirrors (if so equipped)
can be stored in the automatic drive
positioner memory.
Follow this procedure to set the
memory positions:
1
• Confirm that the shift lever is in the P (PARK) position.
• Place the ignition switch in the ON or ACC position.
• Adjust the driver’s seat, steering column and outside mirrors (if so equipped) to
the desired positions using the adjusting switches for each feature.
• Push the SET switch 1 , and within 5 seconds, push the memory switch
(1 or 2) for at least 1 second.
• The indicator light on the memory switch you select will illuminate for
approximately 5 seconds.
• The driver’s seat, steering column and outside mirror positions (if so equipped)
are now set to your preferences.
These memorized positions can also be linked to your Nissan Intelligent Key®.
To link a memorized position to your Nissan Intelligent Key®, press the unlock
button on the key fob after completing the previous step.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
18
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
HEADLIGHT CONTROL SWITCH
Turn the headlight control switch to the
position 1 to turn on the front parking, tail,
license plate and instrument panel lights.
Turn the control switch to the
to turn on the headlights.
4
3
position 2
1
2
AUTOLIGHT SYSTEM (if so equipped)
The autolight system will automatically
turn the headlights on when it is dark and
off when it is light. The system will keep the
headlights on for a period of time after you
turn the ignition off and all the doors
are closed.
5
6
To activate the autolight system, turn the
headlight control switch to the AUTO position
3 then place the ignition switch in the ON position. To deactivate the autolight
system, turn the headlight control switch to the OFF position 4 ,
position
1 or
position 2 .
HIGH BEAM SELECT
With the headlights ON (either in the AUTO or
position), push the lever
forward 5 to select the high beam function. The blue indicator light
will
illuminate in the instrument panel. Pull the lever back to the original position to
select the low beam function and the blue indicator light will extinguish.
Pull and release the lever 6 to flash the headlight high beams on and off.
FOG LIGHT SWITCH (if so equipped)
The headlights must be on and the low
beams selected for the fog lights to operate.
Push the bottom of the
the fog lights on.
To turn them off, push the top of the
switch 8 .
The fog lights will turn off if the headlights are turned off.
8
switch 7 to turn
7
LANE CHANGE SIGNAL
Move the lever up or down until the turn signal begins to flash but the lever
does not latch to signal a lane change. Hold the lever until the lane change
is completed.
Move the lever up or down until the turn signal begins to flash but the lever
does not latch and release the lever. The turn signal will automatically flash
three times.
Choose the appropriate method to signal a lane change based on the road and
traffic conditions.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
19
FIRST DRIVE FEATURES
WIPER AND WASHER SWITCH
Rotate the control ring to one of the following
positions to operate the windshield wipers:
1 Mist (MIST) – One sweep operation of
2 Auto (AUTO) (if so equipped) – Operates
the wipers.
the rain-sensing wipers intermittently.
The intermittent speed can be adjusted
by rotating the control ring to increase or
decrease wiper sensitivity.
3 Low (LO) – Wipers operate at a continuous
4 High (HI) – Wipers operate at a continuous
5 To activate the washer, press the button
low-speed.
4 HI
3 LO
2 AUTO
OFF
1 MIST
5
high-speed.
on the end of the lever. The wipers will operate several times.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
STARTING/STOPPING THE ENGINE
It is important to make sure the Nissan
Intelligent Key® is with you (that is, in your
pocket or purse).
Depress the brake pedal.
Push the ignition switch to the ON position to
start the engine.
TURNING THE ENGINE OFF
Move the shift lever to the P (PARK) position.
Push the ignition switch to the OFF position
to turn the engine off.
START HESITATION (diesel models only)
The starter for diesel models is designed to
not engage until the glow plugs have had
sufficient time to warm up.
1
Engine Warming
Keep Foot on Brake
If the glow plugs need to warm up, the
Engine Warming – Keep Foot on Brake message will appear in the vehicle
information display 1 when the ignition switch is placed in the ON position.
Keep the brake pedal depressed and wait until the Engine Warming – Keep
Foot on Brake message extinguishes.
During cold weather, the glow plugs may need approximately 4 seconds to
warm up.
20
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
Refer to the “Starting and stopping the engine (section 3)” of your Titan Diesel
Owner’s Manual for important information on starting and stopping the
diesel engine.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual, the
“Instrument panel (section 2)” and the “Starting and stopping the engine (section 3)” of your Titan
Diesel Owner’s Manual.
6
7
8
2
3
1
4
5
9
10
HEATER AND AIR CONDITIONER (automatic) (if so equipped)
1 ON•OFF BUTTON
Press the ON•OFF button to turn the system on or off.
2 AUTO BUTTON/DRIVER’S SIDE TEMPERATURE CONTROL DIAL
The automatic mode may be used year-round. Press the AUTO button to
turn the automatic mode on, and the system will automatically control the
inside temperature (automatic cooling and/or dehumidified heating), air flow
distribution and fan speed.
Turn the driver’s side temperature control dial left for cooler air or right for
warmer air.
3 DUAL BUTTON/PASSENGER’S SIDE TEMPERATURE CONTROL DIAL
Press the DUAL button to turn the passenger’s side temperature controls
on or off. This will allow the passenger’s side temperature to be adjusted
independently from the driver’s side.
Turn the passenger’s side temperature control dial left for cooler air or right
for warmer air.
4 FAN SPEED CONTROL BUTTON
Press the side or
fan speed.
side of the button to decrease or increase the
5 MODE BUTTON
Press the MODE button to manually control air flow.
Air flows from the center and side vents.
Air flows from the center, side and foot vents.
Air flows mainly from the foot vents.
Air flows from the front defroster and foot vents.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
21
FIRST DRIVE FEATURES
6 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Press the front defroster button
to turn the system on. The A/C
automatically turns on when the front defroster mode is selected. This
feature removes humidity from the air.
Set the temperature control dial 2 and the fan speed control button 4 to
their maximum settings.
7 REAR WINDOW AND/OR OUTSIDE MIRROR DEFROSTER SWITCH
(if so equipped)
Push the rear window defroster switch
to turn the system on or off.
The rear window defroster automatically turns off after approximately
15 minutes.
8 FRESH AIR INTAKE CONTROL BUTTON
Press the fresh air intake control button
to draw outside air into the
passenger compartment. The indicator light on the button will illuminate.
9 AIR RECIRCULATION BUTTON
Press the air recirculation button
to recirculate air inside the vehicle.
The indicator light on the button will illuminate. This system is used to avoid
certain outside odors and to help adjust the inside vehicle temperature
more effectively.
Press the fresh air intake control button
to turn air recirculation off. This
allows outside air to be drawn into the passenger compartment to prevent
fogging in the front defroster, floor or front defroster/floor mode.
The air recirculation mode cannot be activated when the climate control
system is in the front defroster mode
.
10 A/C BUTTON
Press the A/C button to manually turn the A/C on or off.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” and the “Monitor, climate,
audio, phone and voice recognition systems (section 4)” of your Owner’s Manual.
USB (Universal Serial Bus) CONNECTION PORT/AUX JACK AND
iPod® INTERFACE
The USB port/Aux jack 1 is located on the control panel
below the climate controls.
When a compatible USB memory device or iPod® is plugged
into the USB port, compatible audio files stored on the device
can be played through the vehicle’s audio system and
front display.
Please see your Owner’s Manual for important safety information, system
limitations, and additional operating and feature information.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
22
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
1
1
2
4
6
5
3
FM/AM/SiriusXM® SATELLITE RADIO WITH CD PLAYER
(if so equipped)
1 POWER BUTTON/VOLUME CONTROL KNOB
Press the POWER button to turn the system on or off.
Turn the VOLUME control knob to the right or left to increase or
decrease the volume.
2 ENTER/AUDIO BUTTON/TUNE•SCROLL KNOB
Press the ENTER/AUDIO button to go to the audio settings screen.
To manually tune the radio, turn the TUNE•SCROLL knob left or right.
3 SEEK BUTTONS
To tune and stop at the previous or next broadcast station, press the seek
buttons
or
.
For satellite radio to switch to the first channel of the previous or next
category, press the seek buttons
or
.
To change tracks on a CD, press the seek buttons
To rewind or fast forward a track on a CD, press and hold the seek
buttons
or
.
or
.
4 STATION SELECT KEYS
Twelve stations can be set for the FM band, six for the AM band and 18 for
satellite radio.
To store a station in a preset, you must first select a radio band by pressing
the FM•AM button 5 or SXM button 6 then tune to the desired FM, AM or
satellite radio station.
Next touch and hold the desired station select key (1-6) until a beep is heard.
The channel indicator will appear on the display, and the sound will resume.
Programing is now complete.
To retrieve a previously set station, select the radio band where the preset
was stored then touch the corresponding station select key (1-6).
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
23
FIRST DRIVE FEATURES
CRUISE CONTROL
The cruise control system enables you to set
a constant cruising speed once the vehicle
has reached 25 mph (40 km/h).
The system will automatically maintain the
set speed until you tap the brake pedal,
accelerate, cancel or turn the system off.
To activate the cruise control, push the
ON/OFF switch 1 on the steering wheel.
The
(white) in the vehicle information
display will illuminate.
4
3
2
1
To set a cruising speed, accelerate the vehicle
to the desired speed, push the COAST/SET switch 2 on the steering wheel and
release. The
(green) in the vehicle information display will illuminate. Take
your foot off the accelerator pedal. Your vehicle will maintain the set speed.
To reset at a faster cruising speed, push up and hold the ACCEL/RES switch 3
on the steering wheel. When the vehicle attains the desired speed, release
the switch.
To reset at a slower cruising speed, push down and hold the COAST/SET switch
2 on the steering wheel. Release the switch when the vehicle slows to the
desired speed.
To cancel the preset speed, tap the brake pedal or push the CANCEL switch 4
on the steering wheel.
To turn off cruise control, push the ON/OFF switch 1 on the steering wheel.
The
indicator light in the vehicle information display will extinguish.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
24
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
POWER OUTLETS
2
12V OUTLETS
The 12V power outlets are only powered
when the ignition switch is in the ACC or
ON position.
The 12V power outlets are for powering
electrical accessories such as cellular phones.
The power outlets located below the control
panel 1 , on the passenger’s side of the
control panel 2 and inside the center
console 3 are powered directly by the
vehicle’s battery.
1
3
To use a power outlet, open the cap.
120V OUTLETS (if so equipped)
120V power outlets are not powered directly by the battery
and require the ignition switch to be in the ON position and the
power inverter switch 4 to be depressed.
400W mode is only available with the shift lever in the
P (PARK) position.
The 120V power outlets are for powering
electrical devices up to 120V.
The power outlets located in the 2nd row,
behind the center console 5 , and in the
truck box 6 are powered directly by the
vehicle’s battery.
For devices that require power of 120V or
more, the shift lever must be placed in the
P (PARK) position.
4
5
6
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating and
feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
25
SYSTEM GUIDE
VEHICLE INFORMATION DISPLAY
The vehicle information display 1 displays items such as:
Vehicle settings
Auxiliary gauges
DEF level (diesel models only)
Off-road information
Fuel economy
Trip computer information
Driving aids (if so equipped)
Cruise control system
Indicators and warnings
Tire pressure information
Audio
Drive system warnings and settings (if so equipped)
1
USING THE VEHICLE INFORMATION DISPLAY
The vehicle information display modes can be
changed using the
buttons 2 , the switch
3 and the ENTER button 4 located on the
steering wheel.
Press the
buttons 2 and push the
switch 3 to navigate through the items in
the vehicle information display.
Press the ENTER button 4 to change
or select an item in the vehicle
information display.
Press the
button 2 to go back to the
previous menu.
3
4
2
5
RESETTING THE TRIP COMPUTER
1.Press the
buttons 2 until you reach
the “Trip” screen 5 .
2.Press the ENTER button 4 for more than
1.5 seconds to reset average fuel consumption, average speed, distance to
empty and journey time.
SETTINGS
The setting mode displays the settings that can be changed:
Driver Assistance
(if so equipped)
Meter Settings
Vehicle Settings
Towing Settings
(if so equipped)
Alarm (if so equipped)
Maintenance
Unit
Language
Factory Reset
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
26
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
HANDS-FREE TEXT MESSAGING ASSISTANT*
This system allows for sending and receiving
text messages through the vehicle’s interface.
Using predefined or custom messages, send
a text to a name or phone number stored in
your Bluetooth® Hands-free Phone System.
Once enabled, the text message, sender and
delivery time are shown on the control panel
display when the vehicle speed is less than 5
mph (8 km/h).
Text messages have the option of being read aloud at all vehicle speeds.
Many cellular phones may require special permission to enable text messaging.
Check the cellular phone’s screen during Bluetooth® pairing. For some cellular
phones, you need to enable “Notifications” in the cellular phone’s Bluetooth®
menu for text messages to appear on the touch-screen display. For more
information and instructions, refer to your cellular phone’s Owner’s Manual.
Text message integration requires that the cellular phone support Message
Access Profile (MAP) for both receiving and sending text messages. Some
cellular phones may not support all text messaging features. Please see
www.NissanUSA.com/bluetooth for compatibility information as well as
your device’s Owner’s Manual.
*
aws in some jurisdictions may restrict the use of “Text-to-Speech”. Some of the applications and
L
features, such as social networking and texting, may also be restricted. Check local regulations for any
requirements before using these features.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
BLUETOOTH® HANDS-FREE PHONE SYSTEM*
A cellular telephone should not be used while driving so full attention may be
given to vehicle operation.
SYSTEM OPERATING TIPS
Press the
button on the steering wheel to
interrupt the voice prompts at any time and
speak a command after the tone.
To use the system faster, you may speak the
second level commands with the main menu
command on the main menu. For example,
press the
button on the steering wheel,
and after the tone, say “Redial”.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
27
SYSTEM GUIDE
The “Help” command can be used to hear a
list of available commands at any time.
Reduce background noise as much as
possible by closing windows and pointing
heater and air conditioner vents away from
the ceiling.
Microphone
Speak naturally without long pauses and
without raising your voice.
To cancel a Voice Recognition session, say “Cancel” or “Quit” or press and hold
the
button on the steering wheel for 5 seconds.
To increase or decrease the volume of the voice prompts, push the volume
control switches + or – on the steering wheel or turn the volume control dial on
the audio system while the audio system is responding.
Voice commands can be used to operate various Bluetooth® system features
using the Nissan Voice Recognition system. See your Owner’s Manual for
detailed information.
*Some jurisdictions prohibit the use of cellular telephones while driving.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
BLUETOOTH® SYSTEM WITHOUT NAVIGATION*
(if so equipped)
CONNECTING PROCEDURE
The vehicle must be stationary when connecting the cellular phone.
1.Press the
button on the steering wheel. The system announces the
available commands.
2.Say: “Add Phone”. The system acknowledges the command and asks you to
initiate connecting from the cellular phone handset.
3.Initiate connecting from the cellular phone:
The connecting procedure varies according to each cellular phone model.
For detailed connecting instructions and a list of compatible cellular phones,
please visit www.NissanUSA.com/bluetooth.
When prompted, confirm that the PIN on the display matches the PIN shown
on the handset. If your handset does not support Secure Simple Pairing and
requests you to input a PIN, enter “1234” from the handset.
28
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
PHONEBOOK SETUP
The phonebook stores up to 1,000 entries for each cellular phone paired with
the system.
Depending on your cellular phone, the system may automatically download
your cellular phone’s entire phonebook to the vehicle’s Bluetooth® system.
MAKING A CALL FROM THE PHONEBOOK
1. Press the
button on the steering wheel.
2.After waiting for the tone, say “Call” followed by the name of a phonebook entry.
For example, “Call Michael Smith”.
3. Confirm the correct name is recognized by saying “Dial” after the tone.
MAKING A CALL BY PHONE NUMBER
1. Press the
button on the steering wheel. A tone will sound.
2.Say: “Phone”. The system acknowledges the command and announces the next
set of available commands.
3.Say: “Dial Number”. The system acknowledges the command and announces the
next set of available commands.
4.Say the number you wish to call starting with the area code in single
digit format.
5.When you have finished speaking the phone number, the system repeats it back
and announces the available commands.
6. Say: “Dial”. The system acknowledges the command and makes the call.
RECEIVING/ENDING A CALL
When you receive a cellular phone call, a ring tone sounds through the
audio system.
To accept the call, press the
To reject the call, press the
To hang up the cellular phone at the end of a call or to disconnect during call
placement, press the
button on the steering wheel.
button on the steering wheel.
button on the steering wheel.
*Some jurisdictions prohibit the use of cellular telephones while driving.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
29
SYSTEM GUIDE
BLUETOOTH® SYSTEM WITH NAVIGATION* (if so equipped)
Send predefined or custom text messages through your vehicle’s
Bluetooth® system.
Receive texts through your vehicle’s Bluetooth® system that can be read to you.
Bluetooth® Streaming Audio allows you to use a compatible Bluetooth® device
to play audio files on your device. Your compatible device can be connected to
the vehicle’s audio system, allowing audio files to play through the
vehicle’s speakers.
CONNECTING PROCEDURE
1.Press the
control panel.
button on the
2.Touch the “Settings” key 1 .
3.Touch the “Phone & Bluetooth” key 2 .
4.Touch the “Connect New Device” key 3 .
1
5.Initiate the connecting process from the
handset. The system will display the message:
“Confirm on your Bluetooth device that the
PIN xxxxxx is displayed.”
If the PIN is displayed on your Bluetooth®
device, select “Yes/Pair” to complete the
connecting process.
2
VEHICLE PHONEBOOK
To access the vehicle phonebook:
1. Press the
button on the control panel.
2. Select the “Phonebook” key 4 .
3
3.Choose the desired entry from the
displayed list.
MAKING A CALL
1.Press the
button on the control panel. The
“PHONE” screen 5 will appear on the display.
2. Select one of the following options to
make a call:
“Phonebook”: Select the name from an
entry stored in the vehicle phonebook.
5
4
“Call Lists”: Select the name from the
incoming, outgoing or missed call history.
“Redial”: Dial the last outgoing call from the vehicle.
: Input the phone number manually using the keypad
displayed on the screen.
30
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
RECEIVING/ENDING A CALL
To accept the incoming call, either:
• Press the
wheel, or
• Select the
button on the steering
icon on the screen.
To reject the incoming call, either:
• Press the
wheel, or
button on the steering
• Select the
icon on the screen.
To end a cellular phone call, either:
• Press the
• Select the
button on the steering wheel, or
icon on the screen.
*Some jurisdictions prohibit the use of cellular telephones while driving.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
11
3
9
10
4
5
8
6
7
1
2
NAVIGATION SYSTEM (if so equipped)
Your Navigation System can calculate a route from your current location to
a preferred destination. The real-time map display and turn-by-turn voice
guidance will lead you along the route.
The Navigation System will continually update your vehicle’s position. If you
have deviated from the original route, it will recalculate the route from your
current location.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
31
SYSTEM GUIDE
To help promote safe driving, some functions cannot be operated or have
limited operation when the vehicle speed is above 5 mph (8 km/h). The
on-screen text and keys for these restricted functions will be “grayed-out”
or muted and cannot be selected while driving. These functions will become
available again when the vehicle speed is reduced to 5 mph (8 km/h). Voice
commands may be available for some of the restricted functions. For more
information, refer to the “Monitor, climate, audio, phone and voice recognition
systems (section 4)” of your Owner’s Manual.
1 NAV button – Press to access the functions of the Navigation System.
2 MAP button – Press to display the current location map screen.
3 VOL control knob – Turn right to increase the volume or left to decrease
the volume.
4 key – Select to zoom the map in.
5 key – Select to zoom the map out.
6 button – Press to access SiriusXM Traffic, MyApps, Settings, SiriusXM
Travel Link, Voice Commands, and NissanConnect® Services.
7 button – Press to change the display brightness between day and night
modes. While the mode is being displayed, the brightness can be adjusted using
the TUNE•SCROLL knob. Press and hold to turn the display off. Press again to
turn the display on.
8 BACK button – Press to return to the previous screen.
9 TUNE•SCROLL knob – Turn to navigate the items in a list. Press to select a
menu item.
10 Touch-screen display
11 SD-card location – An SD-card with map data must be inserted here for map
functions to operate.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to your NissanConnect® Owner’s Manual.
32
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
NISSAN MOBILE ENTERTAINMENT SYSTEM (MES)
(if so equipped)
With the MES, you can play DVD videos,
video CDs or CDs that contain music or
sound content. Images will display on the
corresponding monitor. Sound will play
from the vehicle’s audio system (or wireless
headphones provided in the kit) or your own
wired headphones after connecting them to
the headphone jacks of the corresponding
DVD player.
1.Place the ignition switch in the ACC or
ON position.
2.Press the (power) button 1 on each
monitor control panel to power on.
1
2
3
3.Insert a DVD (label facing to the rear of the
vehicle) into either monitor.
4.Press the button 2 to begin playing the DVD if it does not
begin automatically.
5.To eject a DVD:
• Press the
panel, or
button 3 on the corresponding monitor control
• Press the corresponding monitor control button (DVD–A or
DVD–B) on the remote control and then press the
button 3 .
6.To turn the DVD system off:
• Press the
(power) button 1 on the corresponding monitor control panel, or
• Press the corresponding monitor control button (DVD–A or DVD–B) on the
remote control and then press the (power) button 1 .
You can also connect auxiliary devices, such as video games, camcorders,
portable video players or USB devices, to the auxiliary jacks located on the
corresponding monitor control panel. (Your device will be controlled through its
own control panel.)
The system provides a priority for each of the following device inputs:
• RCA ports, USB port, disc player
• A device connected through the RCA connections will override play of the disc
player and USB port.
Use the remote control provided with the system or the buttons on the
corresponding monitor control panel to operate the rear display screens.
Press the AUX button on the factory radio to listen to the audio through the
vehicle’s speakers.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
33
SYSTEM GUIDE
Use the headphones 4 , also provided with
the system, to listen to audio wirelessly and
independently. You may also connect your
own wired headphones to the headphone
jacks 5 located under the port covers of the
corresponding monitor control panel.
To use the headphones, set the select switch
to A or B for use with the Monitor A or
Monitor B respectively.
For the best audio sound quality, please
ensure you are facing the monitor directly in
front of you.
4
5
The wireless headphones will only operate in
the line of sight.
Press the source button 6 on the
corresponding monitor control panel or remote control to allow viewing Monitor
A video on Monitor B and vice versa. Press the source button 6 to cycle
through the available video sources.
6
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
34
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
HOMELINK
HOMELINK® UNIVERSAL TRANSCEIVER (if so equipped)
The HomeLink® Universal Transceiver can learn and consolidate the functions
of up to three different hand-held transmitters, operating items such as garage
doors, property gates, outdoor and indoor lights or alarm systems.
To program the HomeLink Universal Transceiver:
• Position the handheld transceiver 1-3 in (26-76 mm) away from the HomeLink
surface, keeping the HomeLink indicator light in view.
• Press and hold the desired HomeLink button and the handheld transmitter
button simultaneously until the HomeLink indicator light flashes slowly and
then rapidly.
• Both buttons may be released when the indicator light flashes rapidly.
To verify the programing is complete, press and hold the HomeLink button and
observe the indicator light:
• A solid, continuous light indicates the programing is complete and the
HomeLink button will activate your device.
• A blinking light that turns to a solid, continuous light after 2 seconds indicates
additional steps are required to complete the programing.
An additional person may make the remaining steps easier. To complete the
programing process:
• At the receiver of the device that you are programing to the HomeLink
button, press and release the learn or smart button (the name may vary by
manufacturer, but it is usually located near where the hanging antenna wire
is attached to the unit). You have approximately 30 seconds to initiate the
following step.
• Press and hold the programed HomeLink button for 2 seconds and release.
You may have to repeat the previous two steps up to three times to complete
the programing process. HomeLink should now activate your device.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
35
SYSTEM GUIDE
COMPASS (if so equipped)
Press the
button 1 for about 1 second when the ignition switch is placed
in the ON position to toggle the compass display 2 on or off.
The display will indicate the direction the vehicle is heading:
• N: North
• E: East
2
• S: South
• W: West
If the display reads “C”, or for additional
information refer to the “Instruments and
controls (section 2)” of the Owner’s manual.
1
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the
HomeLink website at www.homelink.com or call 1-800-355-3515.
36
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
MEMO
Helpful Resources
Below is a list of helpful resources that can be used
to learn more about the vehicle’s systems and
feature operations.
Vehicle Owner’s Manual
NissanConnect® Navigation Owner’s Manual
(if so equipped)
Printed Quick Reference Guide (this document)
www.NissanUSA.com/bluetooth
www.NissanUSA.com/connect
www.youtube.com/user/NissanUSA
Nissan Consumer Affairs: 1-800-647-7261
Electronic Quick Reference Guide
(Use Quick Response (QR) code or URL below.)
Nissan Quick Guide (available in the iPhone
App Store or Android Google Play™ Store for
download to your smartphone)
To view detailed instructional videos,
go to www.nissanownersinfo.mobi/2018/titan
or snap this barcode with an appropriate barcode reader.
This Quick Reference Guide is intended to provide an overview of some of the unique features of your new
vehicle. Please see your Owner’s Manual for important safety information and system operation limitations.
Features and equipment in your vehicle may vary depending on model, trim level, options selected, order, date of
production, region or availability. Therefore, you may find information about features or equipment that are not
included or installed on your vehicle.
All information, specifications and illustrations in this Quick Reference Guide are those in effect at the time
of printing. NISSAN reserves the right to change specifications, performance, design or component suppliers
without notice and without obligation. From time to time, NISSAN may update or revise this Quick Reference
Guide to provide owners with the most accurate information currently available. Please carefully read and
retain with this Quick Reference Guide all revision updates sent to you by NISSAN to ensure you have access
to accurate and up-to-date information regarding your vehicle. Current versions of vehicle Quick Reference
Guides, Owner’s Manuals and any updates can also be found in the Owner section of the NISSAN website at
https://owners.nissanusa.com/nowners/navigation/manualsGuide. If you have questions concerning
any information in your Owner’s Manual, contact Nissan Consumer Affairs. See the NISSAN CUSTOMER CARE
PROGRAM page in the Owner’s Manual for contact information.
Nissan, the Nissan Brand Symbol, Z and
Nissan model names are Nissan trademarks.
© 2017 Nissan North America, Inc.
QR18EA 0A61U0
Printing: August 2017
Download PDF
Similar pages