Assembly and Operating Instructions for Outback® Hunter Stainless

Assembly and Operating Instructions for Outback®
Hunter Stainless Steel 3 Burner Gas BBQ
THG3302S-3
Photographs are not to scale.
Specifications subject to change
without prior notice.
•
•
•
•
•
•
WARNING
•
•
•
0359
For outdoor use only. Not for commercial use.
Read instructions before using the appliance. Failure to follow instructions could
result in death, serious bodily injury, and/or property loss.
Warning: accessible parts may be very hot. Keep young children and pets away.
Do not move the appliance during use.
Turn off the gas supply at the gas bottle after use.
Any modification of the appliance, misuse, or failure to follow the instructions may be
dangerous and will invalidate your warranty. This does not affect your statutory rights.
Retain these instructions for future reference.
Leak test annually, and whenever the gas bottle is removed or replaced. Check that the
hose connections are tight and leak test each time you reconnect the gas bottle.
For Flare-up control please refer to the ‘OPERATION’ section of this manual.
FOR YOUR SAFETY
If you smell gas:
1.
Shut off gas to the appliance.
2.
Extinguish any open flame.
3.
Open barbecue lid or hood.
4.
If odour continues, discontinue use and
contact your local dealer.
FOR YOUR SAFETY
1.
2.
Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
A gas bottle not connected for use shall not be
stored in the vicinity of this or any other
appliance.
Parts List
Quantities vary according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see ‘Hardware Reference Diagram’.
CODE
PART
QTY
HOOD
A1
A2
A3
A4
Hood (Pre-Assembled to Body)
Hood Handle
Heat Indicator
Warming Rack
1
1
1
1
BODY
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
Cooking Grill
Cooking Griddle
Lava Rock
Lava Rock Basket
Barbecue Body
Knob
Control Panel
Burner
Drip Tray
Drip Tray Left Bracket
Drip Tray Right Bracket
Drip Pan
Hose and Regulator Assembly
1
1
1
1
1
3
1
3
1
1
1
1
1
TROLLEY
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
Left Side Shelf
Right Side Shelf
Left Front Leg
Left Rear Leg
Right Front Leg
Right Rear Leg
Leg Top Support
Screen
Front Fixing Support
Trolley Base
Rear Fixing Support
Leg Endcap
Axle
Wheel
Hubcap
1
1
1
1
1
1
2
1
1
1
1
2
1
2
2
HARDWARE
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
M5x15 Bolt
Washer
M5 Nut
M6x95 Bolt
Spacer
1/4-20UNCx22 Step Bolt
1/4-20UNCx25 Bolt
1/4-20UNCx12 Bolt
Axle Washer
Locknut
4
4
4
8
8
8
8
14
2
2
Pre-Assembled Component
Quantity varies according to model purchased
Appearance, size, and construction may differ according to model purchased
2
Outback® Hunter Stainless
Steel 3 Burner Gas BBQ
Parts Diagrams
Quantities vary according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see hardware pack page.
A1
A3
A4
A2
B1
B2
B3
B4
B5
B8
B6
B7
B10
B13
B11
B9
B12
C4
C6
C3
C5
C2
C1
C7
C8
C11
D10 D9
C14
C13
C10
C15
C9
3
C12
Hardware Reference Diagram
Specifications subject to change without prior notice.
D1,D2,D3
D4,D5
D6
D7
D8
4
Assembly
IMPORTANT!
• TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/Crosspoint screwdriver,
adjustable spanner or metric spanner set.
• Remove any internal components or packaging from the barbecue body.
• Whilst every care is taken in the manufacture of this product, care must be taken during assembly in
case sharp edges are present.
• Please read the Important Information section carefully before assembly and use of your
barbecue.
1
C11
C9
C3
C4
C5
C10
(Photo depicts trolley
from the reverse side)
C6
Attach the Front Fixing Support (C9) and Rear Fixing Support (C11) onto the Trolley Base (C10)
by aligning corresponding holes and fixing with the 1/4-20UNCx12 Bolts (D8x2pcs).
Then attach the Legs (C3, C4, C5, C6) to the trolley base assembly using the 1/4-20UNCx25
Bolts (D7x8pcs). Ensure that the legs with the Velcro attached to them are at the front of the
barbecue, facing inwards.
2
C13
D9
C15
D10
C14
C3
Unscrew the Locknuts (D10) from both ends of the Axle (C13) and remove the Axle Washers
(D9). Slide the axle through the corresponding holes in the left legs. Place axle washers on each
end of the axle. Slide the Wheels (C14) over each end of the axle. Secure the wheels into place
with the locknuts. Place the wheel Hubcaps (C15) onto the outsides of the wheels.
5
3
C7
Attach one Leg Top Support (C7) between the left legs using the 1/4-20UNCx12 Bolts
(D8x6pcs). Repeat above process for the other leg top support.
4
C1
C2
Install a 1/4-20UNCx22 Step Bolt (D6) on each leg, and then attach the Left Side Shelf (C1)
and Right Side Shelf (C2) onto left and right legs using the 1/4-20UNCx22 step bolts. Hook
the side shelves onto the upper step bolts.
6
5
B1
B2
B3
B4
Remove all cast iron cooking components, lava rock, drip tray, and any internal packaging
from the barbecue body.
6
D4
D5
Insert M6x95 Bolts (D4x8pcs) through the trolley legs, the Spacers (D5x8pcs), and keep the tip
of the bolts inside the spacers. While holding the barbecue body into position (2 people required),
screw the bolts into the barbecue body as shown.
CAUTION! Care must be taken to ensure the hood or lid does not fall open unexpectedly
or becomes damaged when it is set on the ground.
When positioning the body of the barbecue, ensure the control panel is on the same side as the
legs with Velcro fastenings.
7
7
D1
B10
D2
D3
Attach Drip Tray Left Bracket (B10) to barbecue body using M5x15 Bolts (D1x2pcs), Washers
(D2x2pcs) and M5 Nuts (D3x2pcs) as shown. Repeat above process for Drip Tray Right
Bracket (B11).
NOTE: Ensure that the big tabs of the brakets which stop the drip tray are located at the
front of the barbecue.
8
B9
B12
Insert the Drip Tray (B9) by sliding it underneath the barbecue body. Insert the Drip Pan
(B12) in position.
8
9
B1
B2
B3
B4
Remove the plastic wrap from the Lava Rock (B3) and then place a uniform layer into Lava
Rock Basket (B4). Lay the lava rock carefully into the body ensuring it lies level within the
body. Lay the cooking grill (B1) and griddle (B2) into place.
NOTE: Ensure that the lava rock lies directly underneath the grills.
10
A4
Step 1
Step 2
Step 3
Step 4
Attach the Warming Rack (A4) to the Hood (A1) and Barbecue Body (B5) as shown. Make
sure that the swing legs fix to the body of the barbecue and the shorter fixed legs go through
the holes in the hood.
9
11
(Left rear view of the barbecue trolley.)
C8
Attach the screen (C8) to the front left/right legs as shown.
12
B13
Connect the Hose and Regulator Assembly (B13) to the barbecue.
Ensure the mating faces of the connection are clean and not damaged. Do not use
any sealing tape, paste, or liquid on the connection. The nut must be tightened with
the use of a spanner. Do not use force which may damage the assembly.
10
Leak Test Diagram
2
1
1. Maximum diameter or breadth is 320mm.
2. Maximum height (regulator included) is 700mm.
ASSEMBLY IS NOW COMPLETE.
PROCEED TO THE NEXT PAGE FOR INSTRUCTIONS ON OPERATION AND
MAINTENANCE
ALL JOINTS AND CONNECTIONS MUST NOW BE LEAK TESTED BEFORE USING THE
BARBECUE.
Leak test annually, and whenever the gas bottle is removed or replaced.
Leak Testing
Always perform a leak test in a well-ventilated area.
Step 1 - Confirm all control knobs are in the off position.
Step 2 - Turn the gas on / open the gas control valve on the gas bottle or regulator.
Step 3 - Check for leaks by brushing a solution of ½ water and ½ liquid detergent / soap over all the
gas system joints, including gas bottle valve connections, hose connections, and regulator
connections.
Step 4 - NEVER USE AN OPEN FLAME to test for leaks at any time.
Step 5 - If bubbles form over any of the joints there is a leak
• Turn off the gas supply at the gas bottle
• Retighten all joints
• Repeat test
• If bubbles form again do not use the barbecue and contact your local distributor for assistance.
Always wipe the mixed solution (½ water and ½
connections after leak testing.
11
liquid detergent / soap) from all joints and
Important Information
nBefore you use your barbecue, perform a
leak test. This is the only safe and sure way
to detect any gas leaking from joints and
connections of the barbecue after
assembly.
nLeak test annually, and whenever the gas
bottle is removed or replaced.
nDo not store flammable materials near this
barbecue.
nDo not use aerosols near this barbecue.
nFailure to follow the manual’s instructions
could result in serious injury or damage.
nParts sealed by the manufacturer or his
agent must not be altered by the user.
nModification of the barbecue may be
dangerous, is not permitted and will nullify
any warranty.
nIf you have any queries regarding these
instructions, contact your local dealer.
Please read these instructions carefully
before assembly and use of your barbecue.
nRetain these instructions for future
reference.
nThis product is for outdoor use only. Do not
use indoors.
nDo not use the barbecue or store gas
bottles below ground level. LP gas is
heavier than air so if a leak occurs the gas
will collect at a low level and could ignite in
the presence of a flame or spark.
nFor use with LPG bottled gas only. A
suitable regulator must be used for butane,
propane or mixes.
nRemove plastic wrap from any part before
lighting.
nDo not use within 1m of any flammable
structure or surface. Do not use under any
combustible surface.
nLP gas bottles should never be placed
directly underneath the barbecue.
nLP gas bottles should never be stored or
used laid on their side, in the horizontal
position. A leak would be very serious and
liquid could enter the gas line with serious
result.
nNever store gas bottles indoors.
nOpen the barbecue hood before lighting.
nOnce lit, do not move the barbecue until it
has completely cooled, after use.
nThis barbecue must not be left unattended
when lit.
nThe hood or lid handle can become very
hot. Grip only the centre of the handle.
Always use oven gloves when cooking or
carrying out any adjustments to the
barbecue.
nUse purpose designed barbecue tools with
long, heat resistant handles.
nUse Caution when opening hood or lid, as
hot steam inside is released upon opening.
nParts of this barbecue become very hot –
care must be taken, especially when
children, elderly people, and animals are
present.
nTurn off the gas supply at the gas bottle
after use.
nNever cover a barbecue until it has
completely cooled.
nUse this barbecue only on a stable, flat
surface.
Gas, Regulator and Hose
This barbecue can use either propane or
butane or propane-butane mixed LPG (liquid
petroleum gas) bottled gas. Propane bottles will
supply gas all year round, even on cold winter
days. Butane bottles will supply sufficient gas in
summer, but it may affect the performance of
the barbecue and restrict the heat output
available from the burners, particularly once the
gas temperature starts to fall below +10°C. A
spanner may be required to change gas bottles.
•
•
•
The hose should hang freely with no bends,
twisting, tension, folds, or kinks that could
obstruct free flow of gas. Always inspect the
hose for cuts, cracks, or excessive wear
before use.
Apart from the connection point, no part of
the hose should touch any hot barbecue
parts. If the hose shows any sign of damage
it must be replaced with a hose suitable for
use with LP gas which meets the national
standards for the country of use.
A suitable hose must comply with EN164361 or local regulation, and the length should
not exceed 1.5 metres.
For optimal performance, we suggest to use a
13kg gas bottle. A suitable regulator must
comply with EN12864 or EN16129. YOU MUST
HAVE THE PROPER REGULATOR AND
BOTTLE IN ORDER FOR THE BARBECUE TO
OPERATE SAFELY AND EFFICIENTLY. USE
OF
AN
INCORRECT
OR
FAULTY
12
solid plate — this includes baking dishes.
Full coverage will cause excessive build-up
of heat and damage the barbecue. This is
not covered by warranty.
REGULATOR IS DANGEROUS AND WILL
INVALIDATE ANY WARRANTY. Please consult
your local gas dealer for the most suitable gas
bottles and regulators.
Preparation Before Cooking
To prevent foods from sticking to the cooking
surface, please use a long handled brush to
apply a light coat of cooking or vegetable oil
before each barbecuing session. (Note:
When cooking for the first time, paint colours
may change slightly as a result. This is normal
and should be expected.) During use, the
protective coating may come off the cooking
surface. This is normal and is not harmful.
Installation
Selecting a Location
This barbecue is for outdoor use only and
should be placed in a well-ventilated area, and
on a safe and even surface. Never place your
barbecue below ground level. Take care to
ensure that it is not placed UNDER any
combustible surface. The sides of the barbecue
should NEVER be closer than 1 metre from any
combustible surface, including trees and fences
and make sure that there are no heat sources
near the barbecue (cigarettes, open flames,
spark etc.). Keep this barbecue away from any
flammable materials!
Line the drip pan with aluminium foil. This will
make cleanup easy.
Lighting the Barbecue
• Open the barbecue hood or lid before
lighting. Never light your barbecue with the
hood or lid closed.
• Ensure all knobs are in the off position.
Open the gas control valve on the gas bottle
or regulator.
• Push the control knob of the burner you wish
to light and turn it anti-clockwise until you
feel resistance to the turning. Pause 4
seconds, then continue turning the control
knob until a click is heard and the burner is
lit. Repeat previous step several times until
the burner is lit.
• Ignite any of the remaining burners in any
order, as needed. Confirm each burner is
alight before igniting another burner.
• If burner fails to ignite after following above
procedure, turn all the knobs to the off
position. Close the gas valve on the gas
bottle. Wait 5 minutes. Reattempt all of the
above steps. If the barbecue still fails to
light, please refer to the manual ignition
instructions below.
• After ignition, turn the burners to the high
position for 3-5 minutes in order to pre-heat
the barbecue. This should be done before
each cooking session. The hood or lid
should be open during preheating.
• After completion of preheating, turn all
burners to the low position for best cooking
results.
Precautions
Do not obstruct any ventilation openings in the
barbecue body.
Position the gas bottle on level ground next to
the barbecue and safely away from any source
of heat.
Should you need to install or change the gas
bottle, confirm that the barbecue is switched off,
and that there are no sources of ignition
(cigarettes, open flame, sparks, etc.) near
before proceeding.
Connecting a Gas Hose to the Barbecue
Connect the gas hose to the gas rail inlet on the
left hand side of the barbecue. Do not
overtighten. Do not use any sealing tape, paste
or liquid on the connection.
Fixing a Regulator to the Gas Bottle
Confirm all barbecue control knobs are in the off
position. Connect the regulator to the gas bottle
according to your regulator and bottle dealer’s
instructions.
Operation
nWarnings
n
Before proceeding, make certain that you
understand
the
IMPORTANT
INFORMATION section of this manual.
n
Your barbecue is not designed to be used
with more than 50% of the cooking area as a
Manual lighting instructions
• Open the barbecue hood or lid before
lighting. Never light your barbecue with the
hood or lid closed.
• Ensure all knobs are in the off position.
13
Open the gas control valve on the gas bottle
or regulator.
Insert lit match through the right matchlighting hole on the right side of the
barbecue body and place near rightmost
burner porthole.
Push and turn the rightmost control knob
anti-clockwise to the high position, taking
care to protect yourself from the flames.
When the right burner is lit, turn the
remaining burners on from right to left.
Confirm that each burner is alight before
turning on the next burner.
If a burner fails to ignite, contact your local
dealer for assistance.
After ignition, turn the burners to the high
position for 3-5 minutes in order to pre-heat
the barbecue. This should be done before
each cooking session. The hood or lid
should be open during preheating.
After completion of preheating, turn all
burners to the low position for best cooking
results.
bake or roast on a metal baking tray and set it
on one side of the cooking grill.
Grill Cooking
The burners heat up the lava rock, underneath
the grill, which in turn heats the food on the grill.
The natural food juices produced during
cooking fall onto the lava rock below and
vaporise. The subsequent rising smoke bastes
the food, as it travels upwards, imparting that
unique barbecued flavour.
Warming Rack
Warming racks are a convenient way to keep
cooked food warm or to warm items such as
bread rolls. It is advisable to place food
(particularly fatty foods) to the front of the
warming rack to avoid the possibility of juices
and fat running down the back of your
barbecue. Always check that your warming rack
is properly fitted before use.
•
•
•
•
•
•
•
Turn the burner directly under the food to the
OFF position and turn all other burners to a
LOW to MEDIUM position.
Close the hood to cook the food ‘indirectly’.
Avoid lifting the hood unnecessarily as heat is
lost every time the hood is opened. If the hood
is opened during cooking please allow extra
time for the barbecue to regain its temperature
and complete the cooking. Use the temperature
gauge to monitor the heat of the barbecue.
If the internal heat becomes too high, turn the
burners down to the low position. It is not
necessary or advisable to have all of the
burners on high when the hood is closed.
DO NOT ALLOW YOUR BARBECUE TO
OVERHEAT. Be careful of hot steam when
opening the hood.
Griddle Plate Cooking
The burners heat the griddle plate directly,
which then cooks the food on contact. Griddle
plates allow for the cooking of smaller items,
such as seafood, which could fall through the
spaces of a grill. They are also suitable for
cooking items that require high-temperature/
short-duration cooking, such as vegetables and
smaller cuts of fish. Similarly, it can be used in
exactly the same way as a griddle in the
kitchen, for searing steaks, cooking eggs, etc.
Alternatively, it can be used for heating pans or
keeping food warm.
Flare-Up Control *Very Important*
Flare-ups occur when meat is barbecued, and
its fat and juices fall upon the hot lava rock.
Smoke of course helps give food its barbecued
flavour, but it is best to avoid excessive flare-up
to prevent food being burned. To control flareups, it is ABSOLUTELY ESSENTIAL to trim
away excess fat from meat and poultry before
grilling, use cooking sauces and marinades
sparingly and try to avoid very cheap cuts of
meat or meat products as these tend to have a
high fat and water content. Also, the burners
should always be placed on the low setting
during cooking.
Roasting Hood Cooking
Barbecues equipped with a roasting hood give
the option to form an ‘oven’ for roasting or
baking food, such as joints of meat or whole
chickens, etc. More even cooking of food will
actually be achieved by using the barbecue with
the hood down. However, this should only be
done with the burners on low.
When flare-ups do occur, they can usually be
extinguished by applying baking soda or salt
directly onto the lava rock. Always protect your
hands when handling anything near the cooking
surface of the barbecue and take care to
protect yourself from the flames.
If a fat fire occurs, please see the instructions
For best results, place the food you wish to
14
given below.
moist areas.
Fat Fires
Empty and clean the drip tray and drip pan (and
foil liner, if applicable) of food debris after each
cooking session. If the barbecue is to be used
for large gatherings, it will be necessary to turn
off and cool the barbecue every two hours to
remove food debris from the drip tray and drip
pan (and foil liner, if applicable), and clean it
out. The time between cleaning may need to be
reduced if very fatty foods or cheap meat
products are being cooked. Failure to do this
may result in a fat fire, which may cause injury
and could seriously damage the barbecue.
n
Never handle hot parts with unprotected
hands.
n
Never douse the barbecue with water when
its surfaces are hot.
In order to extend the life and maintain the
condition of your barbecue, we strongly
recommend that the unit be covered when left
outside for any length of time, especially during
the winter months. Heavy-duty barbecue covers
and other accessories are available from your
local stockist.
Even when your barbecue is covered for its
protection, it must be inspected on a regular
basis as damp or condensation can form which
may result in damage to the barbecue. It may
be necessary to dry the barbecue and the
inside of the cover. It is possible for mould to
grow on any fat remaining on parts of the
barbecue. This should be cleaned off smooth
surfaces with hot soapy water.
In the event of a fat fire:
• If safe to do so, turn all control knobs to the
‘off’ position.
• Turn off the gas supply at the gas bottle.
• Keep everyone at a safe distance from the
barbecue and wait until the fire has burnt
out.
• Do not close the hood or lid of the barbecue.
• NEVER DOUSE A BARBECUE WITH
WATER. IF AN EXTINGUISHER IS USED,
IT SHOULD BE A POWDER TYPE.
• DO NOT REMOVE THE DRIP TRAY.
• If the fire does not seem to be abating or
appears to be worsening, contact your local
Fire Brigade for assistance.
Any rust that is found that does not come into
contact with the food should be treated with a
rust inhibitor and painted with barbecue paint or
a heat resistant paint.
Cooking Surfaces & Warming Rack
When the barbecue has cooled, clean with hot
soapy water. To remove any food residue, use
a mild cream cleaner on a non-abrasive pad.
Do not use scouring pads or powders as they
can permanently damage the finish. Rinse well
and dry thoroughly. Due to the weight of the
cooking surfaces, we do not recommend
cleaning in a dishwasher.
End of Cooking Session
After each cooking session, turn the barbecue
burners to the “high” position and burn for 5
minutes. This procedure will burn off cooking
residue, thus making cleaning easier. Make
sure the hood or lid is open during this process.
Turning Off Your Barbecue
When you have finished using your barbecue,
turn all the control valves fully clockwise to the
“Off” position, then switch off the gas supply at
the bottle.
It is quite normal for surface rust to be present
on the cooking surface. If rust appears between
uses or in storage, clean with a soft brass wire
brush. Be careful not to damage the cooking
surface, re-oil and cure.
Wait until the barbecue is sufficiently cool
before closing its hood.
Care and Maintenance
Burner
Provided that they are operating correctly, in
normal usage, burning off the residue after
cooking will keep the burners clean.
Regularly clean your barbecue between uses
and especially after extended periods of
storage. Ensure the barbecue and its
components are sufficiently cool before
cleaning. Do not leave the barbecue exposed to
outside weather conditions or stored in damp,
The burners should be removed and cleaned
annually, or whenever heavy build-up is found,
to ensure that there are no signs of blockage
(debris, insects) in either the burner portholes or
the primary air inlet of the burners. Use a pipe
cleaner to clear obstructions.
15
The wood used in the manufacture of your
barbecue will naturally weather and change its
appearance. It is quite natural for small cracks
to appear on the surface of the wood. Do not
expose to sun or rain directly. The wood should
be regularly inspected and any weathered or
damaged surfaces should be sanded and
recoated promptly with a garden furniture
varnish or paint, following the manufacturer’s
instructions for preparation and application.
When refitting the burners, be careful to check
that the neck of the burner fits over the valve
outlet.
It is quite normal for surface rust to be present
on the burners. If rust appears between uses or
in storage, clean with a soft brass wire brush.
Lava Rock
It is not necessary to remove and wash the lava
rock in order to keep it clean. Burning off the
residue for 3 to 5 minutes after each cooking
session
should
be
sufficient.
Heavily
impregnated lava rock should be turned over so
that the dirty side faces the burners in order to
burn off any residue. Replacement lava rock is
available from your local stockist.
Fixings
All screws and bolts, etc. should be checked
and tightened on a regular basis.
Storage
Ensure the barbecue is properly cooled before
covering or storing. Store your barbecue in a
cool dry place.
Drip Tray
After every use, empty and clean the drip tray
(and foil liner, if applicable) of any fat or food
particles, using a plastic or wooden scraper if
necessary.
Cover the burners with aluminium foil in order to
prevent insects or other debris from collecting in
burner holes.
If the barbecue is to be stored indoors, the gas
bottle must be disconnected and left outside.
The gas bottle should always be stored outside,
in a dry, well-ventilated area, away from any
sources of heat or ignition. Do not let children
tamper with the bottle.
Failure to keep it clean, and excessive build up
can result in a fat fire. This can be hazardous
and severely damage the barbecue. This is not
a fault in the barbecue and is therefore not
covered by the terms of the warranty. If
required, the tray can be washed in hot soapy
water.
When using the barbecue after extended
periods of storage follow the cleaning
procedures.
Barbecue Body
Regularly remove excess grease or fat from the
barbecue body using a cloth wrung out in hot
soapy water and dry thoroughly. Excess fat and
food debris can be removed from inside the
body using a soft plastic or wooden scraper. It
is not necessary to remove all the grease from
the body. If you need to clean fully, use hot
soapy water and a cloth, or nylon-bristled brush
only. Do not use abrasives. Remove cooking
surfaces and burners before full cleaning. Do
not immerse the gas controls or manifold in
water. Check burner operation after carefully
refitting into body.
Barbecue Hood or Lid
Use a non-abrasive cloth or pad and clean with
hot, soapy water. Do not use scouring pads or
powders as they can permanently damage the
finish.
Trolley
Wipe with a cloth wrung out in hot soapy water
and dry.
16
Technical Specifications
Outback®
Hunter
Stainless
Steel 3
Burner
Gas BBQ
Notes:
CE
Approval
Heat
Input
Burners
Injector
Size
Gas /Pressure
0359
359BR665
12.96
kW
3
1.02mm
Butane: 28-30mbar
Propane: 37mbar
Gas Consumption: 943g/hr
Countries of Use:
BE, CH, CY, CZ, ES, FR, GB, GR, IE, IT, LT, LU, LV, PT, SK,
I3+ (28-30/37)
SI
Specifications are subject to change without prior notice.
17
Troubleshooting
Problem
Possible Cause
Solution
Burner will not light using
the ignition system
LP gas bottle is empty
Replace with full bottle
Faulty regulator
Have regulator checked or replaced
Obstructions in burner
Clean burner
Obstructions in gas jets or gas hose
Clean jets and gas hose
Electrode wire is loose is connected on
electrode
Reconnect wire
Electrode or wire is damaged
Change electrode and wire
Faulty integral ignitor
Change ignitor
LP gas bottle is empty
Replace with full bottle
Faulty regulator
Have regulator checked or replaced
Obstructions in burner
Clean burner
Obstructions in gas jets or gas hose
Clean jets and gas hose
LP gas bottle too small
Use larger bottle
Obstructions in burner
Clean burner
Obstructions in gas jets or gas hose
Clean jets and gas hose
Windy conditions
Use barbecue in a more sheltered
position
Integral ignition system jammed
Replace gas valve
Gas valve jammed
Replace gas valve
Burner will not light with a
match
Low flame or flashback (fire
in burner tube— a hissing or
roaring noise may be heard)
Gas valve knob difficult to
turn
Manufacturer:
TPA Industrial (DG) Co. Ltd.
Xingguang Rd., Huangjiang, Dongguan
Guangdong, China 523768
18
OUTBACK® WARRANTY
OUTBACK® barbecues are warranted to the original purchaser against defects in materials
and workmanship. OUTBACK® will supply replacements for defective parts free of charge
provided that:
♦
♦
♦
♦
The product has not been used for trade, professional or hire purposes.
The product has not been subjected to misuse or neglect, including fat fires and flare ups
or use of a faulty or incorrect regulator.
The product has not sustained damage through foreign objects, substances or accidents.
The care and maintenance instructions given in your OUTBACK® manual have been
followed.
Any warranty and guarantee claims shall be rendered void in the event of improper use of the
barbecue or the use of non-approved fuels. Discolouration, rusting or slight deformation of
parts exposed directly to the flames (grill, griddle, flame tamer, burner, etc.) do not impair the
function of the barbecue and do not form a basis for any claims.
This warranty is offered as an extra benefit and is in addition to the customers’ statutory rights.
OUTBACK® does not in any way warranty the gas cylinder.
In the unlikely event that you experience problems with this barbecue, please fill in our
warranty form at:
http://www.outbackbarbecues.com/warranty-form
One of our colleagues will be in contact with you shortly.
For reference and correspondence, record your
serial number here.
(See sticker on side of barbecue body.)
Serial No.__________________
This number may be required when ordering
spare parts or accessories. A part reference
number may also be required where applicable.
HELPLINE NUMBER: 0345 388 6032
19
Download PDF
Similar pages