Spec Sheet - TET3GN, TET3GN31, TET3GN32, TET3GN33

TET3GN Series
EcoPower® Toilet Flushometer Valve, 1.6 gpf
FEATURES
ED
• Hydropower self-generating system
• Electronic flushometer valve complete with
1" angle stop and 1-1/2" vacuum breaker set
• 1.6 gpf or less
• Back spud floor, top spud and back spud wall
models - concealed 4" x 4" Cover plate
• 24 hour automatic flush for trap seal protection
MODELS
O
N
T
TET3GN32#SS (1-1/2" Vacuum breaker)
Top spud, Satin finish
• Complete set supplied with:
Vacuum breaker & angle stop set - VB9RB-32
(Top spud)
• 1" Angle stop - 10077t5
• 1-1/2" Vacuum breaker - 10075t3
• Outlet tube - TH559EDV177
• Sweat solder kit - SJ3
IN
TET3GN31#SS (1-1/2" Vacuum breaker)
Back spud wall, Satin finish
• Complete set supplied with:
Vacuum breaker & angle stop set - VB13RB-31
(Back spud wall)
• 1" Angle stop - 10077t5
• 1-1/2" Vacuum breaker - 10075t4
• Outlet tube - TH559EDV176
• Sweat solder kit - SJ3
U
TET3GN#SS
Valve only, Surface mount, Satin finish
D
IS
C
TET3GN33#SS (1-1/2" Vacuum breaker)
Back spud floor, Satin finish
• Complete set supplied with:
Vacuum breaker & angle stop set - VB13RB-33
(Back spud floor)
• 1" Angle stop - 10077t5
• 1-1/2" Vacuum breaker - 10075t4
• Outlet tube - TH559EDV175
• Sweat solder kit - SJ3
Optional Part:
Z-4000-J - Adapter for ground joint angle stops
COLORS/FINISHES
• #SS Stainless Steel Satin finish
CODES/STANDARDS
• Meets or exceeds ASSE 1037, CSA B125.3
• Certifications: IAPMO(cUPC), ASSE, State of
Massachusetts, City of Los Angeles, and others
• Code Compliance: UPC, IPC, NSPC, NPC Canada,
and others
• ADA compliant
Piston Valve
PRODUCT SPECIFICATION
TOTO® Model No. _____________________________
Automatic Infrared sensor activated, toilet valve.
Heavy-duty 4” x 4” stainless steel coverplate with satin
finish. Low water consumption of 1.6 gallons per flush.
Piston valve with stainless steel self-cleaning debris
screen and self-cleaning solenoid. Automatic flush
every twenty four hours if not used. Electrical sensor
separated from valve and sealed in a waterproof
compartment. Manual override button incorporated.
Through the use of TOTO’s EcoPower® Flush Valves,
using the valve 12 flushes per day will fully recharge
the valve for up to 10 years.
TET3GN Series
EcoPower® Toilet Flushometer Valve, 1.6 gpf
SPECIFICATIONS
INSTALLATION NOTES
•
•
The recommended installation for the toilet
flushometer valve is to have a 7" (178mm) minimum
space in wall. Also a minimum 12” x 12” access
panel or walk-in chase is required for service and
maintenance.
•
•
•
•
•
Do not place grab bars in front of sensor for ADA
stalls. See diagram below for detailed measurements.
ED
•
•
Three Year Warranty
Bronze casting with
stainless steel satin finish
Power Supply
Hydropower self-generating
system
Water Supply
1" NPT
Detection time
Factory setting at six (6)
seconds minimum
Detection range
Self-adjusting to environment
Discharge quantity
Preset to 1.6 gpf / 6.0 lpf
Operating temperature 32°-104°F (0°-40°C)
Supply water pressure 15 psi - 125 psi*
Trap seal protection
Automatically flushes once
after twenty four (24) hours
of non-use
Wall thickness: Min. 5/8" (16mm) - Max. 1-5/8" (41mm).
Contact TOTO for different thickness.
U
•
Warranty
Material
O
N
T
IN
These specifications are subject to change without notice.
*Water pressures over 80 psi are not recommended for most plumbing fixtures.
Check your local plumbing code for details.
DIAGRAM
RECOMMENDED INSTALLATION
4-3/4”
TET3GN-31#SS
Top Spud
Back Spud Floor Mount
Back Spud Wall Mount
3-15/16” x 3-15/16”
of
sensor
IS
D
4-3/4”*
OVERRIDE BUTTON
LOCATION
SENSOR
LOCATION
TET3GN-33#SS
Finished wall
4-3/4”*
TOTO
EcoPower®
TET3GN-32#SS
Opening in Wall:
C
1-3/4”
3-3/8”
Dimensions: Inch
2-3/8”
Supply
x
6 - 7-1/8”
Finished wall
Finished wall
2-3/8”
2-3/8”
of
of
sensor
Supply sensor
Supply
x
x
11”
16”
frame
16”
Supply
of frame
and fixture
5”
2-1/4” Min.
* +/- 1/2”
Always position the sensor above upright toilet seats and grab bars
X= At least 5” clearance from sensor to tip of toilet seat up
position or to top of grab bar is required to avoid false detection.
Elbow
Nut Bowl
Bowl
(3-3/4"- 4-7/8") *
(3-3/4"- 4-7/8") *
Bowl 3”
(3-3/4"- 4-7/8") *
Depending on X, the frame may not be centered to Supply CL as shown.
*Leave some room for elbow nut from the wall for future maintenance.
These dimensions and specifications are subject to change without notice
Ph: (888) 295-8134 | Fax: (800) 699-4889 | www.totousa.com
#SS-00091, v.05
Printed in U.S.A. | © TOTO USA 10/09 | Printed on recycled paper ♻
Download PDF
Similar pages