http://certification.space/User-Guide.pdf
USING YOUR BREWER
OWNER’S MANUAL: Getting the most from your new
Platinum B70 Keurig® Brewer
COMMENT UTILISER VOTRE CAFETIÈRE
MANUEL D’UTILISATION : Tirez le meilleur de votre
nouvelle cafetière Platinum B70 de Keurig®
IMPORTANT SAFEGUARDS
TABLE OF CONTENTS
Safe Operation & Use
KEURIG GOURMET SINGLE CUP HOME BREWING SYSTEM
Platinum B70 — Using Your Brewer
®
http://certification.space/User-Guide.pdf
When using electrical appliances, basic
safety precautions should be followed,
including the following:
1. Read all instructions before using.
2. Do not touch hot surfaces. Use handles and
knobs when available.
3. T
his appliance must be properly installed and
located in accordance with these instructions
before it is used.
4. The use of accessory attachments not recom-
mended by the appliance manufacturer may result in fire, electrical shock or injury to persons.
5. Do not place on or near a hot gas or electric
burner, or in a heated oven.
6. Do not use outdoors.
7. To protect against fire, electric shock and injury
do not immerse cords, plugs, or the appliance in
water or any other liquid.
8. Do not overfill the Water Reservoir with water.
9. Use only water in this appliance! Do not put any
other liquids or foods in the Water Reservoir
except as instructed in the Cleaning Instructions in this guide.
10. T
urn off and unplug the Brewer before
cleaning or maintenance. Allow to cool
before putting on or taking off parts and
before cleaning the appliance.
event of an electrical short circuit, grounding
reduces the risk of electrical shock.
11. F
or best operation, plug the appliance into its
19. I f the outlet is a standard 2-prong wall outlet,
12. D
o not operate any appliance with a damaged
20. Do not, under any circumstances, cut or
own electrical outlet on a dedicated circuit to
prevent flickering of lights, blowing of fuses or
tripping a circuit breaker.
cord or plug or after the appliance malfunctions or is damaged in any manner. Contact
Keurig® Customer Service to report any
malfunction of or damage to the Brewer.
13. D
o not let the cord hang over the edge of
the table or counter, or touch hot surfaces.
14. To disconnect, press the Power Button on the
Brewer to ‘OFF’ status and then remove the
plug from the wall outlet.
15. C
lose supervision is necessary when any
appliance is used by or near children.
it is your personal responsibility and obligation
to have it replaced with a properly grounded
3-prong wall outlet.
remove the third (ground) prong from the
power cord or use an adapter.
21. Consult a qualified electrician if the grounding
instructions are not completely understood, or
if doubt exists as to whether the appliance is
properly grounded.
22. Do not use the appliance for other than
its intended use.
Save These
Instructions.
16. D
o not lift the Handle to open the Lid of
WARNING TO USERS AND PARENTS
17. Always keep the Water Reservoir Lid on
1. DO NOT permit children to use brewer unless there
is adult supervision. Brewer dispenses very hot water.
the Brewer while brewing is in progress.
the Water Reservoir unless you are refilling it.
18. T
his appliance is equipped with a power cord
having a grounding wire with a grounding plug.
The appliance must be grounded using
a 3-hole properly grounded outlet. In the
2
2. SPECIAL NOTICE FOR HOT COCOA USERS:
IMMEDIATELY AFTER USING A HOT COCOA K-CUP,
RUN a Hot Water Brew Cycle without a K-Cup to avoid
the possibility of clogging the exit needle. DO NOT assume
the next user will do this.
CAUTION: There are two sharp needles that puncture the K-Cup portion pack,
one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. To
avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.
®
SET-UP
Helpful Hints......................................................................................... 4
Unpacking............................................................................................. 4
Features................................................................................................ 5
CAUTION: There is extremely hot water in the K-Cup Holder during the
brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup Assembly Housing during the brewing process.
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to
SECTION 1 — SET-UP & FIRST BREW
Set-Up & First Brew............................................................................ 6
reduce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set
or extension cord should be at least as great as the electrical rating of the
appliance; (2) the cord should be arranged so that it will not drape over the
countertop or tabletop where it can be pulled on by children or tripped over unintentionally; and (3) the extension cord must include a 3-prong grounding plug.
SECTION 2 — CONTROLS & INDICATORS
Setting the Clock................................................................................ 10
Programming On/Off Features....................................................... 10
Programming Brew Temperature.................................................. 12
Programming Brew Size.................................................................. 13
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
SECTION 3 — CLEANING & MAINTENANCE
Cleaning............................................................................................... 13
De-Scaling.......................................................................................... 14
Storage................................................................................................ 15
WARNING
THIS PRODUCT CONTAINS CHEMICALS, INCLUDING
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING
RISK OF FIRE OR
ELECTRIC SHOCK
DO NOT OPEN
SECTION 4 — TROUBLESHOOTING.................................................. 16
SECTION 5 — WARRANTY................................................................. 17
!
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE THE
BOTTOM COVER. NO USER SERVICEABLE
PARTS ARE INSIDE. REPAIR SHOULD BE DONE
BY AUTHORIZED SERVICE PERSONNEL ONLY.
Pour des directives en français, veuillez vous reporter à la page 18.
Record your Brewer Serial Number here.
Removing the serial number label from the Brewer will void warranty.
3
Set-up
Helpful Hints
1. Keep your Brewer turned “ON” at all times.
To brew a fresh cup of coffee, tea or hot cocoa
anytime you want, we suggest you keep your
Brewer turned “ON” all the time. However, the
Brewer is fully programmable so you can set it
to turn on and off automatically to match your
schedule. Or, if you prefer, set the Brewer to
automatically turn off after a period of time.
Follow the simple instructions on pages 10–13
to make using the Brewer convenient for you.
2. For the best tasting gourmet coffee, tea or
hot cocoa, Keurig recommends using bottled
water or the Keurig® Water Filter Starter Kit
(available at www.keurig.com).
Water quality varies from place to place. If you
notice an undesirable taste in your cup of
coffee, such as chlorine or other mineral tastes,
we recommend you consider using bottled
water or water from a filtration system.
3. Customize the Size, Flavor & Brew That’s
Perfect for You.™
With the choice of over 200 varieties of K-Cups
and 5 brew sizes (Iced Beverage-3.25 oz., Small
Cup-5.25 oz., Small Mug-7.25 oz., Large Mug9.25 oz., and Travel Mug-11.25 oz.) your Keurig®
Features
Brewer gives you endless options to customize
the size, flavor and brew that’s perfect for you.
For a strong, intense cup, select an Extra Bold
K-Cup® (with up to 30% more ground coffee
than regular varieties) and brew the size that’s
right for you. The smaller the brew size, the
more intense flavor in your cup. The larger the
brew size, the less intense flavor in your cup.
4. Plug Brewer into its own grounded outlet.
If the electric circuit is overloaded with other
appliances, your Brewer may not function
properly. The Brewer should be operated on its
own circuit, separate from other appliances.
5. Brewing into a travel mug.
To brew into a travel mug, simply remove the
Drip Tray Assembly and place the travel mug
on the Drip Tray Base.
6. De-scale Brewer regularly.
Please see pages 14 and 15 for instructions.
Unpacking Instructions
1. Place Brewer box on a large steady surface
(such as a table or countertop) or on the floor.
Open the box.
2. Remove enclosed literature.
4
Platinum — Model B70 Brewer
http://certification.space/User-Guide.pdf
3. Turn the box on its side with front of box face down.
D
4. Reach into the box and grasp the plastic bag
P
A
that contains the Brewer.
G
5. Carefully pull the plastic bag (and packaging
READY
TO BREW
materials) toward you and out of the box. The
Brewer will still be encased in the polyfoam
and be on its side.
M
6. Remove the top polyfoam packaging material.
7. Carefully lift Brewer off of the bottom polyfoam
F
H
C
B
E
and place it upright on a flat, steady surface.
0
8. L
ift plastic bag off of Brewer.
9. Record the serial number for this Brewer on
page 3 of this guide. The serial number can be
found on the bottom of the Brewer box or on the
Brewer behind the Drip Tray (when removed).
I
We recommend you save all packing materials in
case future shipping of the product is necessary.
WARNING:
Keep all plastic bags away
from children.
Q
J
N
K
L
10. Place the Brewer upright on a flat, steady
surface. Remove tape holding Water Reservoir
in place.
MENU
B. Water Reservoir
C. Water Reservoir
Lock Tab Slot
D. Handle
E. Funnel
F. K-Cup® Portion Pack
Holder (E and F are the
K-Cup Holder Assembly)
G. Lid
H. K-Cup® Portion Pack
Assembly Housing
BREW
S
T
Controls
and Indicators
Platinum B70 Brewer
A. Water Reservoir Lid
MENU
I. Housing
N. Power Cord
P. LCD Control Center
J. Drip Tray Plate
O. Power Switch (Not
Q. Left Button
K. Drip Tray
L. Drip Tray Base
M. Vent
shown) Located Rear
Right Side of Brewer
R. Right Button
S. MENU Button
T. BREW Button
5
R
SECTION 1
Set-Up & First Brew
IMPORTANT: You cannot use your Keurig® Brewer until
fig.
it has been set up for its first use.
NOTE: If Brewer has been exposed to temperatures
below freezing, allow Brewer at least two hours to
reach room temperature before brewing. A frozen
or extremely cold Brewer will not operate.
fig.
1
Lock Tab
2
http://certification.space/User-Guide.pdf
fig.
5. Place Water Reservoir base into
the left side of the Brewer and be
sure the Water Reservoir Lock
Tab engages with the Brewer.
Replace Lid on Water Reservoir.
4
Setting Up Your Brewer
a grounded outlet. Remove all pieces of
packing tape and clear plastic sticker
from LCD display.
fig.
3
will come on and indicate “NOT
READY” and the BREW Button
will flash. NOTE: A K-Cup should
not be used for this sequence.
8. The Brewer will automatically fill the internal
2. Place a large mug (10 oz. minimum) on the
NOT READY
Drip Tray Plate.
3. Remove the Water Reservoir from Brewer
by first removing Lid from the Water Reservoir
(fig. 1), then lifting the Water Reservoir straight
up and toward front of Brewer. (may be tight),
(fig. 2). Rinse with fresh water.
MENU
MENU
BREW
4. Fill Water Reservoir with bottled or filtered
tank with water and then the water will be
heated. This will take about 4 minutes.
During the heating period, “NOT READY”
(fig. 3) is displayed on the LCD Control Center.
Do not lift Brewer Handle during this
‘heating period’. Once the water is heated,
“READY TO BREW” will be displayed and the
BREW Button will flash (fig. 4).
fig.
10. The one-time set-up process is now
6. Lower the Handle to close the Lid over the
complete and you are ready to brew!
MENU
K-Cup Holder. (When it is closed completely,
the LCD Control Center will indicate “READY
TO BREW”. The Left and Right Buttons will
be lit and the BREW Button will flash up to 60
seconds.)
NOTE: The Brewer may take 15-30 seconds
between brews and then “READY TO BREW”
will be displayed.
BREW
Ready to Brew Your First Cup
fig.
5
a. All brew size icons are lit with the default
1. LCD Control Center will indicate
fig.
“READY TO BREW”.
2. Place a cup or mug on the Drip Tray Plate.
READY
TO BREW
3. Lift the Handle and the K-Cup® Holder
will open toward you (fig. 5).
4. Select a K-Cup portion pack.
NOTE: Do not remove the foil lid
or puncture the K-Cup.
MENU
MENU
BREW
6
CAUTION: There are two sharp needles that
puncture the K-Cup, one above the K-Cup Holder
and the other in the bottom of the K-Cup Holder.
To avoid risk of injury, do not put your fingers in
the K-Cup Assembly Housing.
MENU
NOTE: You may see small amounts of water
coming from the Vent and dripping into
water so that the water level is just below the
top edge of the Water Reservoir.
6
NOTE: A K-Cup should not be used for this
Sequence.
7. The Blue LCD Control Center
1. Unwrap cord and plug the Brewer into
in the K-Cup Holder (fig. 6).
brew without a K-Cup. Pour the hot water into
the sink.
READY
TO BREW
6. Press and release the Power
Switch found directly behind the
right side of the Brewer. Switch
is spring loaded and will return
to original position.
5. Place a K-Cup portion pack
the Water Reservoir during this and subsequent
heating — this is normal.
9. Press the BREW Button to start a cleansing
7
7
size flashing (fig. 7). To choose a different size,
press Left Button to go down in size or Right
Button to go up in size.
NOTE: The Small Mug (7.25 oz. serving) is the
factory set default brew size. To program your
favorite brew size see page 13 “Programming
Your Brew Size”.
b. Your choices are a stronger Small Cup (5.25
oz. serving), a Small Mug (7.25 oz. serving), a
Large Mug (9.25 oz. serving), a Travel Mug
(11.25 oz. serving) or Iced Beverage setting
(3.25 oz. serving).
SECTION 1 Set-Up & First Brew (continued)
http://certification.space/User-Guide.pdf
10. Enjoy your first cup of Keurig Brewed®
c. To use the Iced Beverage setting, place a tall
Iced Beverage
(3.25 oz.)
Large Mug
(9.25 oz.)
Small Cup
Travel Mug
Small Mug
it heats water for the next brew cycle. The
“READY TO BREW” indication will return to
the LCD Control Center in about 15 seconds.
(11.25 oz.)
(7.25 oz.)
Stopping the Brew Process
BREW Button will stop flashing, Left and Right
Buttons will no longer be lit and icon
of brew size will be lit.
If you need to stop the brewing after the process has started, press and
release the Power Switch to turn the Brewer ‘OFF’. The flow of coffee, tea
or hot cocoa will stop, the heating element will shut off and the blue lights
illuminating the LCD Control Center and Water Reservoir will disappear.
7. The LCD Control Center will now display the
word ‘BREWING’ and the serving size you
selected will be illuminated on LCD (fig. 8).
fig.
BREWING
MENU
MENU
BREW
8
NOTE: You may get more coffee, tea or hot cocoa in your cup during your next
brew. We recommend that you perform a cleansing brew with water-only after
a terminated brew. Then your NEXT brew will be the volume you have selected.
CAUTION: There is extremely hot water in the KCup Holder during the brew process. To avoid risk
of injury, do not lift the Handle or open the
K-Cup Assembly Housing during the brew process.
Adding Water
8. There may be a short pause prior to coffee
being dispensed. The entire brew process lasts
for approximately 1 minute and ends with a
burst of air to remove all liquid from the K-Cup.
The LCD Control Center of your Brewer will indicate when the water level
in the tank is low or if the Water Reservoir has been removed by displaying
the words “ADD WATER” (fig. 9). The blue light in the Water Reservoir will
also blink when water needs to be added. The Brewer will not allow you to
brew when “ADD WATER” is displayed (fig. 9).
9. Lift the Handle, remove and dispose
of the used K-Cup.
9
Purging the Brewer
The Water Reservoir can be filled in two ways.
1. Lift off the Water Reservoir Lid and pour
11. Your Brewer may display “NOT READY” as
d. Once size is chosen, press BREW Button.
(5.25 oz.)
fig.
gourmet coffee, tea or hot cocoa!
glass filled with ice on the Drip Tray Plate. Use
your favorite K-Cup®, select the Iced Beverage
brew size and press the BREW Button. Add
more ice once brewing is complete, add cream
and sugar if desired.
NOT READY
ADD
WATER
If your Brewer has not been used for more than one week, you should purge
the water from the inner tank.
water directly into the Water Reservoir
while it is still attached to the Brewer,
then replace the Lid.
1. If there is water in the Water Reservoir, remove the Lid, then lift the
Water Reservoir straight up and away from Brewer. Discard water, rinse
and refill with water. Place the Water Reservoir back on the Brewer and
replace the Lid. (If there is no water in the Water Reservoir, simply refill.)
2. Remove the Water Reservoir from Brewer by
MENU
MENU
BREW
first removing Lid from the Water Reservoir, then
lifting the Water Reservoir straight up and toward
front of Brewer. Fill with water. Place the Water
Reservoir back on the Brewer and replace the Lid.
2. Be sure the Brewer is turned on. Raise and lower the Handle on the
Brewer without inserting a K-Cup.
IMPORTANT: Do not remove the Water Reservoir
during the brewing process.
3. The LCD Control Center will display “READY TO BREW”.
Brew a Travel Mug (11.25 oz. serving) of water (do not use a K-Cup).
4. Repeat steps 2 and 3 two more times to completely purge water from
inner tank.
Brewing Hot Water
If you are experiencing any problems with your Brewer, please contact
Customer Service at 1.866.901.BREW (2739).
Your Brewer is able to produce hot water for making hot cocoa from a packet,
for use in cooking, for making soups, etc. Simply follow the instructions on
page 7 —“Ready To Brew Your First Cup” without adding a K-Cup.
NOTE: After brewing a hot cocoa K-Cup, we recommend running a hot water
brew cycle without a K-Cup.
CAUTION: K-Cup will be hot.
8
9
SECTION 2
Controls & Indicators (LCD Control Center)
6. The correct time should now be displayed in the LCD Control Center.
NOTE: If power is interrupted to the Brewer by unplugging it, or if power is
lost, follow the procedure above to reset the time as the clock will not be
visible until the time is set. Brew size and brew temperature menu settings
are remembered and restored automatically. All other settings will be
restored automatically after clock is set.
Setting the clock is optional. When the clock is set, the time will appear in
the LCD Control Center. NOTE: You must set the clock if you will be using the
Auto On/Off Time programming feature.
H
10
M
NOT READY
SET CLOCK
AUTO OFF
ONOFF TIME
BREW TEMP
BREW SIZE
MENU
Set
Hours
BREW
1. Press the MENU Button.
2. The word ‘OFF’ will appear at the top of the
Set
Minutes
fig.
1. Leave it ON all the time. The Brewer can be left on all the time so that it is
flashing “H” until you have reached the
appropriate hour. If the hour has passed 12
“PM” will be shown.
(NOTE: Although the clock remains on, if set, you can not brew a cup of coffee,
tea or hot cocoa.) Press and release the Power Switch again to restore
power to the Brewer. You will have to wait for the water to heat up before
the Brewer is ready to brew.
4. Press or hold the Right Button under the
flashing “M” to set the minutes.
READY
TO BREW
AUTO OFF SET
MENU
2. S
et the Brewer to “AUTO OFF” following a specified period of time after the
last brew.
5. When you have reached the correct time, press the MENU Button six
times to scroll through the remaining programming steps.
a. Press the MENU Button twice to program the Auto Off feature. The LCD
Control Center will now display the programming options with a small
arrow next to “SET AUTO OFF” (fig. 11).
10
fig.
H
MENU
BREW
12
13
M
CLOCK
AUTO OFF
SET ON
TIME
BREW TEMP
e. If you want to set an “OFF TIME”, repeat the
procedure above in steps b & c to set your
desired “OFF TIME” (fig. 14).
BREW SIZE
MENU
MENU
Set
Hours
3. P
rogram your Brewer for a specific On/Off
Time. NOTE: To use this programming feature,
the clock must be set to the correct time. The
clock will not be displayed unless the time is set.
Set
Minutes
BREW
fig.
H
PM
14
M
NOT READY
a. After setting the correct time (required), press
the MENU Button three times to program
On Time feature . The LCD Control Center will
show the programming options with a small
arrow next to “SET ON TIME” (fig. 13).
CLOCK
AUTO OFF
SET
OFF TIME
BREW TEMP
BREW SIZE
MENU
b. Press or hold the Left Button under the “H” to
scroll through the hours to your desired “ON
TIME” hour.
MENU
Set
Hours
11
BREW
c. Press or hold the Right Button under the
“M” to scroll through the minutes to your
desired “ON TIME” minutes.
d. After setting the desired time, press the
MENU Button to save the “ON TIME” and
move to the “SET OFF TIME” (fig. 14).
NOT READY
d. To cancel the Auto Off feature, press the
MENU Button twice to reach the “AUTO OFF”
programming mode. Press and release the
blue Left Button under the blinking “H”
to advance one hour at a time until “OFF”
is displayed.
The Brewer provides three modes so that you can enjoy gourmet coffee, tea
or hot cocoa on your own schedule. By programming your Brewer to turn on
each morning, you will never have to wait for the Brewer to warm up to brew
a gourmet cup of coffee. It will take the Brewer approximately 4 minutes to
warm up from room temperate.
always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To
turn the Brewer off at any time, simply press and release the Power Switch.
b. Press or hold the Left Button under the
blinking “H” to advance 1 hour at a time, up
to 9 hours.
c. After setting the desired Auto Off time, press
the MENU Button five times to scroll through
the remaining programming options and exit
the programming mode. “AUTO OFF SET”
(fig. 12) will now be displayed to indicate that it
has been set.
Programming On/Off Features
LCD Control Center to indicate that the
clock is not set (fig.10). The programming
options will appear on the LCD Control
Center with a small arrow pointing to ‘SET
CLOCK’. “H” (Hour) will appear above the
Left Button and “M” (Minute) will appear
above the Right Button. The “H” and “M”
icons and Left and Right Buttons will flash.
3. Press or hold the Left Button under the
MENU
11
http://certification.space/User-Guide.pdf
Setting the Clock
fig.
fig.
Set
Minutes
f. To complete the process, press the MENU
Button three more times to exit the
programming mode. The Control Center
will now indicate the options you have set.
g. The Auto On time and Auto Off time functions
operate independently from one another. To
cancel either set function, follow the steps
above and use the “H” and “M” Buttons to
advance to 12:00 AM. Make sure the “M”
Button is set to :00, then change the “H”
Button. When you reach 12:00 AM, the
Control Center will display ‘OFF’ and the
function will be disabled.
EXAMPLE: If you chose to set the On Time at
6:55 AM and the Off Time for 10:00 PM, then
the Brewer will be “READY TO BREW” and
maintain hot water in the tank during that
time so that it is always ready for you to brew.
If you wanted to brew outside this window,
SECTION 3
SECTION 2 Controls & Indicators (LCD Control Center)
fig.
H
15
M
NOT READY
SET CLOCK
AUTO OFF
ONOFF TIME
BREW TEMP
BREW SIZE
MENU
MENU
Set
Hours
BREW
Set
Minutes
Programming Brew Temperature
simply press the Power Button and you can
brew as soon as the water is heated and the
“READY TO BREW” indicator is displayed on
the LCD Control Center.
http://certification.space/User-Guide.pdf
5. To change the brew temperature again, repeat steps 1 through 3 to change
(187° – 192º F)
The Brewer brews at a preset temperature of 192°. You can adjust this
temperature down by 5 degrees if you prefer a cooler cup of coffee, tea
or hot cocoa. Simply follow the instructions below.
NOTE: The On time and Off time functions
operate independently from one another. To
cancel either function, follow the steps above
and use the “H” and “M” Buttons to advance to
12:00 AM. When you reach 12:00 AM,
the Control Center will display ‘OFF’ and the
function will be disabled (fig. 15).
fig.
-
NOT READY
16
AUTO OFF SET
ONOFF TIME SET
SET BREW TEMP
BREW SIZE
MENU
-
the programming options with a small
arrow next to “SET BREW TEMP” (fig. 16).
Also, the temperature 192° (initial setting)
will be displayed at the top of the LCD
Control Center to indicate the current
temperature setting.
3­­­. A minus sign will appear over the Left
MENU
BREW
Center five times to program the Brew
Temperature feature.
+
Button and/or a plus sign over the Right
Button. Use these Buttons to raise or lower
the temperature one degree at a time.
4. Once you have reached your desired brew
temperature, press the MENU Button twice
to exit the programming mode. “BREW TEMP
SET” will be displayed in the LCD Control
Center if you have changed it from 192°.
12
Cleaning External Parts
the temperature up or down, remembering that the temperature can only
be between 187° and 192°.
Regular cleaning of the Brewer’s external components is recommended.
1. Never immerse the Brewer in water or other liquids. The Housing
NOTE: At high altitudes (over 5,000 feet) if boiling occurs use the temperature adjustment (+0 and -5 degrees) to lower the temperature.
and other external components may be cleaned with a soapy, damp,
non-abrasive cloth.
Programming Your Brew Size
fig.
2. T he LCD Control Center will now display
+
CLOCK
NOTE: The Auto Off timer and the On/Off Time
programming options operate independently,
but can also be programmed to work together.
For example, you can set the On Time function to
turn on at 7:00 AM and then set the Auto Off timer
function to turn off the Brewer two hours after
the last brew.
1. Press the MENU Button on the LCD Control
READY
TO BREW
17
2. The Drip Tray can accumulate up to 12 ounces of overflow. The Drip Tray
and Drip Tray Plate should be periodically inspected and rinsed clean.
To remove the Drip Tray Assembly, simply slide it toward you, keeping it
level at all times to avoid spilling. The Drip Tray and Drip Tray Plate should
not be placed in the dishwasher. They should be cleaned with a damp,
soapy, non-abrasive cloth and rinsed thoroughly.
he Brewer is preset with the Small Mug
T
(7.25 oz.) as the default brew size. The default
brew size allows the user to avoid scrolling
through brew sizes if a particular size is
chosen most often.
To change the default brew size to your
desired brew size:
MENU
fig.
1. Press the MENU Button six times.
Cleaning the K-Cup Holder
Assembly
Assembly can be placed onto the top shelf of a
dishwasher. NOTE: Use low temperature cycles
in the dishwasher. To remove from the Brewer,
open the cover by lifting the Handle. Grasp the
top of the K-Cup Holder with one hand while
pushing up on the bottom of the K-Cup® Holder
from underneath with the other until it releases
(fig. 18). After cleaning, align the K-Cup Holder
with the opening using the two front ribs as a
guide, and snap into place from the top.
desired default brew size (fig. 17).
3. Once the desired default brew size is selected
BREW
18
1. Cleaning the Parts —The K-Cup Holder
2. Using Left and Right Buttons, select your
MENU
Cleaning & Maintenance
press the MENU Button once to exit. The LCD
will display the brew size set.
13
Download PDF
Similar pages