Installation Instructions for Sloan SF Series Electronic Sensor

Code No. 0816496
Rev. 3 (08/10)
INSTALLATION INSTRUCTIONS FOR SLOAN SF SERIES
ELECTRONIC SENSOR ACTIVATED LAVATORY FAUCETS
SF-2100 Series
SF-2300 Series
Adapter Powered with Battery Backup,
Sensor Activated, Pedestal Style Lavatory Faucets
Adapter Powered with Battery Backup
Sensor Activated, 4” Centerset Lavatory Faucets
SF-2150 Series
SF-2350 Series
Battery Powered, Sensor Activated,
Pedestal Style Lavatory Faucets
Battery Powered, Sensor Activated
4” Centerset Lavatory Faucets
SF-2200 Series
SF-2400 Series
Adapter Powered with Battery Backup
Sensor Activated, Gooseneck Style
Lavatory Faucets
Adapter Powered with Battery Backup,
Sensor Activated, Pedestal Style Lavatory
Faucets
SF-2250 Series
SF-2450 Series
Battery Powered, Sensor Activated
Gooseneck Style Lavatory Faucets
Battery Powered, Sensor Activated,
Pedestal Style Lavatory Faucets
LIMITED WARRANTY
Sloan Valve Company warrants its SF Series Electronic Hand Washing Faucets to be made of first class materials, free from defects of material or workmanship under normal use and
to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of one year from date of purchase.
During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost,
and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or
organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY
RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
PRIOR TO INSTALLATION
Prior to installing the Sloan SF Series Electronic Lavatory Faucet, install
the items listed below. Also, refer to the appropriate rough-in diagram.
• Plug-In Adapter
Models SF-2100/SF-2200/SF-2300/SF-2400 only — Install
electrical receptacle(s) for plug-in adapter(s) — 120 VAC, 1 amp
service for each 6 VDC plug-in adapter used.
International models may be supplied with a 220 VAC/VDC
transformer.
• Hot and cold water supply lines or tempered water supply line
• Drain lines
International models are supplied with 1/2” G water connections.
Important:
• INSTALL ALL ELECTRICAL WIRING IN ACCORDANCE WITH
NATIONAL/LOCAL CODES AND REGULATIONS.
• INSTALL ALL PLUMBING IN ACCORDANCE WITH APPLICABLE CODES
AND REGULATIONS.
• A 6 VDC STEP-DOWN ADAPTER MUST BE USED FOR HARDWIRE
APPLICATIONS.
• BEFORE CONNECTING COPPER TUBE(S) OR FLEX HOSE(S) TO
SUPPLY STOP(S), FLUSH ALL WATER LINES UNTIL WATER IS CLEAR.
TOOLS REQUIRED FOR INSTALLATION
• Electric drill for drilling anchor holes (1/4” or 6 mm drill bit)
• Straight blade and phillips blade screwdrivers
• Open end wrenches (9, 11, 13, 16, 22 mm)
The components supplied with International Models of the SF Series Faucets may vary from what is shown in this manual. Consult factory to identify
variations that may apply to your market.
FAUCET ROUGH-IN
SF-2200 / SF-2250 Series
SF-2100 / SF-2150 Series
2-1/8”
(54 mm)
SPOUT
SPOUT
1-1/4” (32 mm)
MIN. DIA. HOLE
REQUIRED
TRIM PLATE
2-1/8” (54 mm)
TRIM PLATE - Supplied with
SF-2200/SF-2250
Optional item for
SF-2200-INTL/SF-2250-INTL
GASKET
1-1/4” (32 mm)
MIN. DIA. HOLE
REQUIRED
1-1/2” (38 mm) MAX.
DECK THICKNESS
RETAINER
SF-2300 / SF-2350 Series
COPPER TUBE
OR FLEX HOSE
36” (914 mm)
LONG SENSOR
CABLE
1-1/2” (38 mm) MAX.
DECK THICKNESS
RETAINER
1/2” NPSM TO
3/8” COMPRESSION
CONNECTION Not Required for
INTL Models
24” (610 mm)
LONG FLEX HOSE
NUT
GASKET
CONTROL MODULE
6-9/32”
(160 mm)
TEMPERED
SUPPLY
1” (25 mm) MIN.
DIA. HOLE
REQUIRED
SPOUT
HOT AND COLD WATER
SUPPLY APPLICATIONS
SLOTTED MOUNTING
WASHERS (2)
1-1/2” (38 mm) MAX.
DECK THICKNESS
WING NUTS (2)
SF-2400 / SF-2450 Series
BDM VARIATION
(BELOW DECK
MECHANICAL) MIXING
VALVE
HOT
SUPPLY
3/8” (10 mm)
BAK-CHEK TEE
2-1/8”
(54 mm)
SPOUT
TRIM PLATE - Supplied with
SF-2400/SF-2450
Optional item for
SF-2400-INTL/SF-2450-INTL
COLD
SUPPLY
COPPER TUBES OR FLEX HOSES - Flex Hoses Supplied Only with
some International Models.
1-1/4” (32 mm)
MIN. DIA. HOLE
REQUIRED
GASKET
NUT (2)
RETAINER
SIDE VIEW
10”
(254 mm)
3-7/8”
(98 mm)
5-1/4”
(133 mm)
4-1/2”
(115 mm)
4-39/64”
(119 mm)
27°
4-45/64”
(117 mm)
4-1/2”
(114 mm)
1-1/2” (38 mm)
MAX. DECK
THICKNESS
20°
20°
7”
(180 mm)
40°
2
1A - SF-2100/2150 & SF-2400/2450
SERIES: INSTALL FLEX HOSE
AND MOUNTING STUDS
1B - SF-2200/2250 & SF-2300/2350
SERIES: INSTALL FLEX HOSE
A Install Mounting
Studs.
B Install Flex Hose.
A Install Flex Hose.
2A - SF-2100/2150, SF-2200/2250, & SF-2400/2450 SERIES: INSTALL SPOUT, TRIM
PLATE AND SPACER
Pedestal
Spout
Pedestal
Spout
Pedestal
Spout
Trim Plate
Trim Plate
Trim Plate
Spacer
Spacer
Spacer
2B - SF-2300/2350 SERIES: INSTALL SPOUT
A Apply a bead of plumbers putty around the outside of the
Faucet underbody.
3
3A - SF-2100/2150 & SF-2200/2250 SERIES: INSTALL RUBBER GASKET, RETAINER,
AND RETAINER NUT(S)
A Secure Faucet to the Deck by installing Rubber
Gasket, Retainer and Retainer Nut(s). Tighten
Retainer Nuts securely. Do not overtighten.
Rubber
Gasket
Retainer
Rubber
Gasket
Retainer
Retainer
Nut
Rubber
Gasket
Retainer
Retainer
Nut
Retainer
Nuts
3B - SF-2300/2350 SERIES: INSTALL SLOTTED MOUNTING WASHERS AND
WING NUTS
A Secure Faucet to the Deck by installing Slotted Mounting
Washers and Wing Nuts. Tighten Wing Nuts securely. Do not
overtighten.
SLOTTED
MOUNTING
WASHER
WING NUT
4 - INSTALL CONTROL MODULE IN AN APPROPRIATE LOCATION (SEE ROUGH-INS)
Control Module
A Using Control Module as a template, mark mounting holes on
wall. When installed, Sensor Cable and Flex Hose need some
slack.
B Drill 1/4” (6 mm) hole at each mounting hole location.
C Install Plastic Anchors (supplied) into mounting holes in wall.
Note: Adapter — For 3/8”
Connections only.
D Install Control Module to wall using Fasteners supplied.
4
5 - CONNECT SENSOR CABLE AND WATER LINES TO CONTROL MODULE
A Connect Sensor Cable (from Faucet).
Note: Adapter —
For 3/8” Connections only.
B Connect Flex Hose (from Faucet).
C Connect Water Line (supplied with INTL Models
only) to Supply Stop and Control Module.
C
A
B
6 - INSTALL BATTERIES
A Loosen Cover Screws and remove Cover from Control Module.
A
B Remove Battery Compartment, remove compartment lid using
screwdriver and install four (4) AA-size batteries (supplied) as
indicated by the (+) and (—) symbols inside the Battery
Compartment. Replace compartment lid and tighten with
screwdriver.
C Reinstall Battery Compartment into the Control Module.
D Reinstall Control Module Cover using all four (4) Screws.
B
7A - CONNECT ADAPTER (ADAPTER POWERED MODELS ONLY) AND TURN ON
WATER SUPPLY
B Plug Adapter into
Receptacle.
C Turn on Water
Supply.
A Plug Adapter Jack into Control Module.
5
7B - GANG ADAPTER INSTALLATION
!!!!IMPORTANT!!!!
PLUG-IN GANG ADAPTER KIT SFP-35-A
DO NOT PLUG IN THE ADAPTER UNTIL ALL
CONNECTIONS ARE MADE
To connect multiple faucets to a single adapter, use the Sloan
SFP-35-A Gang Adapter Kit (Purchase Separately).
The SFP-35-A Gang Adapter Kit is supplied with cables to connect up
to 6 faucets. To connect up to 8 faucets, purchase 2 additional
SFP-38 Cable Splitters separately.
Plug-in Gang
Adapter
SFP-36
Cable
Splitter
SFP-38
A Connect the Adapter and Cables to the Sensor Faucets as
shown below.
For complete installation, refer to instructions packaged with Gang
Adapter Kit.
To
Additional
Faucets
(6 Max.)
SFP-35-A Gang Adapter Kit is available in 120 VAC only
Cable Splitter
SFP-38
Cable Splitter
SFP-38
8 - SET RANGE ADJUSTMENT
NOTE: Sensor Range can be adjusted after power is supplied to the
Faucet (battery or hardwire).
B Place your hand (or card) in front of the sensor at the distance
you desire the Faucet to activate. Leave hand or card at this
location while the sensor range is setting. Remove hand or
card when the sensor light turns off. The sensor range is now
set.
A Hold the red button in until the sensor flashes (approximately 3
- 6 seconds).
NOTE: The sensor range is dependent on the distance of your hand or
card while the sensor is in range setting mode.
NOTE: If no target is placed in front of the sensor, the sensor range
will set to its longest distance.
9 - SET WATER FLOW TIME-OUT
NOTE: There are two available time-out settings; 7 seconds and 70
seconds.
A Hold the red button in for more than six seconds. The water
flow time-out setting will change from 7 seconds to 70 seconds
or from 70 seconds to 7 seconds.
6
10 - TEST FAUCET OPERATION
1. Place hands under faucet. Solenoid valve should “click,” LED in
sensor window should blink once and water should flow from the
spout.
2. When hands are removed, the water flow should stop.
CARE AND CLEANING OF CHROME AND SPECIAL FINISHES
DO NOT USE abrasive or chemical cleaners (including chlorine bleach)
to clean Faucets that may dull the luster and attack the chrome or
special decorative finishes. Use ONLY mild soap and water, then wipe
dry with clean cloth or towel.
While cleaning the bathroom tile, protect the Faucet from any
splattering of cleaner. Acids and cleaning fluids will discolor or remove
chrome plating.
TROUBLESHOOTING GUIDE
1. Faucet delivers water in an uncontrolled manner.
A. Faucet is defective. Contact Sloan Valve Company Installation
Engineering Department (see below).
2. Faucet does not deliver any water when Sensor is activated.
INDICATOR: Solenoid valve produces an audible “CLICK.”
A. Water supply stop(s) closed. Open water supply stop(s).
B. Water strainer in control module is clogged. Close supply stops
and remove water inlet line at control module. Remove, clean
and reinstall strainer and water inlet line. Replace strainer if
required.
INDICATOR: Solenoid valve DOES NOT produce an audible
“CLICK.”
A. Batteries low (battery powered models). Replace batteries.
B. Power failure (adapter powered models). Check power supply.
3. Faucet delivers only a slow flow or dribble when Sensor is
activated.
A. Water supply stop(s) are partially closed. Completely open water
supply stop(s).
B. Water strainer in control module is clogged. Close supply stops
and remove water inlet line at control module. Remove, clean
and reinstall strainer and water inlet line. Replace strainer if
required.
C. Aerator is clogged. Remove, clean, and reinstall aerator. Replace
aerator if required.
D. Valve is defective. Contact Sloan Valve Company Installation
Engineering Department (see below).
4. Faucet does not stop delivering water or continues to drip after
user is no longer detected.
A. Valve is defective. Contact Sloan Valve Company Installation
Engineering Department (see below).
5. The water temperature is too hot or too cold on a Faucet
connected to hot and cold supply lines.
A. Supply Stops are not adjusted properly. Adjust Supply Stops.
When assistance is required, please contact Sloan Valve Company
Installation Engineering Department at:
1-888-SLOAN-14: (1-888-756-2614)
7
PARTS LIST
1B
1A
1C
1D
12
11
3
5B
13
2H
2D
10
2E
10A
2C
2A
7
4
2B
8
5A
2F
Item
No.
1A
1B
1C
1D
2
2A
2B
2C
2D
2E
2F
2G
2H
3
4
5A
6
7
8
9
6
Part
No.
9
Description
—
—
—
—
SFP-4
Pedestal Faucet Assembly w/ Outlet (Models SF-2100/SF-2150)
Gooseneck Faucet Assembly w/ Outlet (Models SF-2200/SF-2250)
Faucet Assembly w/ Outlet (Models SF-2300/SF-2350)
Pedestal Faucet Assembly w/ Outlet (Models SF-2400/SF-2450)
Mounting Hardware Kit, (Models SF-2100/SF-2150 and
SF-2400/SF-2450) includes Items: 2A, 2B, 2D, 2E and 2F
SFP-5 Mounting Hardware Kit, (Models SF-2200/SF-2250) includes
Items: 2F, 2G and 2H
SFP-16 Mounting Hardware Kit, (Models SF-2300/SF-2350) includes
Items: 2C and 2F
—
Beveled Gasket
—
Metal Retainer
ETF-546-A Gasket, Washers (2), Wing Nuts (2) & Compression Fitting
—
Threaded Stud
—
Retainer Nut
—
Screws and Anchors for Control Module
—
Metal Washer
—
Gasket
SFP-6 Plug-in Adapter (110 VAC/6 VDC) – (USA)
SFP-20 Plug-in Adapter Type G Rectangular (220 VAC/6 VDC) – (UK)
SFP-25 Plug-in Adapter Type C Round Pin (220 VAC/6 VDC) – (EUR)
SFP-26 Plug-in Adapter Type A Flat Blade (220 VAC/6 VDC) – (CH)
—
Batteries-AA size (4)
SFP-40-A 6-Pin Control Module w/ range adjustment button
—
Inlet adapter - 1/2" NPSM to 3/8" Compression Connection
(not supplied with most international models)
SFP-10 Flex Hose, Control Module to Spout
SFP-11 Trim Plate w/ Spacer (not supplied with most international models)
ETF-617-A 3/8” Bak-Chek® Tee Compression Fitting
10C
Item
No.
Part
No.
10B
Description
Accessories
10
10A
10B
10C
SFP-35-A
SFP-36
SFP-38
SFP-37
Gang Adapter Kit (100-240 VAC/ 6 VDC), includes:
Plug-in Gang Adapter (100-240 VAC/ 6 VDC)
Cable Splitter, 51”/1300 mm (5 included in kit)
Cable Extension, 51”/1300 mm
Repair Parts
11
12
13
SFP-41
SFP-15
Sensor (adjustable range - identified by a 6 pin connector)
Strainer (located in water inlet of control module)
Solenoid Assembly for SF control module
IMPORTANT:
Sloan added the range adjustment feature in August 2008
for faucets made prior to August 2008 use the following
replacement items:
11
5B
Sensor (identified by a 4 pin connector)
4-pin Control Module
SFP-34
SFP-8
Replacement Aerators & Spray Heads (not shown)
Models: SF-2100/2150, SF-2300/2350 & SF-2400/2450
SFP-13 0.5 gpm/1.9 Lpm Spray head
SFP-23 2.2 gpm/8.3 Lpm Aerator
SFP-15 0.5 gpm/1.9 Lpm Vandal Resistant Spray Head
SFP- 24 2.2 gpm/8.3 Lpm Vandal Resistant Aerator
Models: SF-2200/2250
SFP-12 Gooseneck Spout w/ outlet
SFP-14 1.5 gpm/5.7 Lpm Laminar Spray Head
Items without part numbers are not sold separately
The information contained in this document is subject to change without notice.
SLOAN VALVE COMPANY • 10500 SEYMOUR AVENUE • FRANKLIN PARK, IL 60131
Phone: 1-800-982-5839 or 1-847-671-4300 • Fax: 1-800-447-8329 or 1-847-671-4380 • www.sloanvalve.com
Copyright © 2010 SLOAN VALVE COMPANY
Code No: 0816496 – Rev. 3 (08/10)
Download PDF
Similar pages