Operating instructions
Digital indicator, model DI32-1
Digital indicator, model DI32-1
EN
EN Operating instructions model DI32-1
Page
3 - 70
© 2015 WIKA Alexander Wiegand SE & Co. KG
All rights reserved.
WIKA® is a registered trademark in various countries.
2
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
Further languages can be found on www.wika.com
Contents
Contents
1. General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. Design and function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
8
8
3. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 Improper use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.4 Personnel qualification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.5 Labelling, safety marks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4. Transport, packaging and storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5. Commissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1 Requirements for the installation location. . . . . . . . . . . . . . . . . . . . . . . . 13
5.2 Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.4 Switching on the digital indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.5 Connection examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
14122699.02 10/2016 EN
6. Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.1 Key functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.2 Menu navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.3 Setting the numeric values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.4 Accessing and exiting programming mode. . . . . . . . . . . . . . . . . . . . . . . 21
7. Voltage or current measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.1 Selecting the input signal and measuring range. . . . . . . . . . . . . . . . . . . 22
7.2 Setting the indication range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.3 Selecting the number of decimal places. . . . . . . . . . . . . . . . . . . . . . . . . 23
7.4 Scaling the input signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.5 Setting the offset adjustment (TARE) . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.6 Setting the zero point suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.7 Select the overrun and underrun behaviour. . . . . . . . . . . . . . . . . . . . . . 25
7.8 Linearising the sensor values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.9 Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
WIKA operating instructions digital indicator, model DI32-1
3
EN
Contents
9. Frequency measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9.1 Selecting the input signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9.2 Selecting triggering of the pulse input. . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9.3 Select frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
9.4 Selecting pulse length limiting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
9.5 Setting the indication range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.6 Selecting the number of decimal places. . . . . . . . . . . . . . . . . . . . . . . . . 34
9.7 Scaling the pulse signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9.8 Setting the offset adjustment (TARE) . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9.9 Linearising the sensor values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
9.10 Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
10.Rotational speed measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
10.1 Selecting the input signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
10.2 Selecting triggering of the pulse input. . . . . . . . . . . . . . . . . . . . . . . . . . . 39
10.3 Selecting pulse length limiting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
10.4 Setting pulses per rotation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
10.5 Selecting the time base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
10.6 Selecting the number of decimal places. . . . . . . . . . . . . . . . . . . . . . . . . 41
10.7 Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
11.Up/Down counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
11.1 Selecting an up or down counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
11.2 Selecting triggering of the pulse input. . . . . . . . . . . . . . . . . . . . . . . . . . . 43
11.3 Selecting the counter basis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.4 Setting the edge control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.5 Setting the prescaler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
11.6 Selecting pulse length limiting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
11.7 Setting the upper indication value and upper pulse count value. . . . . . 46
11.8 Selecting the number of decimal places. . . . . . . . . . . . . . . . . . . . . . . . . 46
11.9 Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
8. Temperature measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.1 Selecting measuring element and measuring range. . . . . . . . . . . . . . . 29
8.2 Select unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.3 Setting the impedance matching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.4 Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Contents
12.General settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
12.1 Setting the measuring time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
12.2 Setting the moving average determination. . . . . . . . . . . . . . . . . . . . . . . 49
12.3 Limiting the indication range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
12.4 Assigning key functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
12.5 Selecting display blinking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
12.6 Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
13.Switching outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.1 Selecting the switching function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
13.2 Setting a switching window (window function). . . . . . . . . . . . . . . . . . . . 54
13.3 Selecting switch behaviour for limit value errors. . . . . . . . . . . . . . . . . . . 54
13.4 Selecting switch behaviour. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13.5 Setting the switching threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
13.6 Setting the hysteresis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13.7 Setting the switch-off delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13.8 Setting the switch-on delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13.9 Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
14.Password protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
14.1 Setting the password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
14.2 Activating/deactivating the password protection . . . . . . . . . . . . . . . . . . 60
14.3 Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
15.Factory settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
15.1 Restoring factory settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
15.2 Overview of the factory settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
16.Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
17.Maintenance and cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
18.Dismounting, return and disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
14122699.02 10/2016 EN
19.Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Appendix: EC declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Declarations of conformity can be found online at www.wika.com
WIKA operating instructions digital indicator, model DI32-1
5
EN
1. General information
1. General information
■■ The digital indicator described in these operating instructions has been
■■ These operating instructions contain important information on handling the
instrument. Working safely requires that all safety instructions and work instructions are observed.
■■ Observe the relevant local accident prevention regulations and general safety
regulations for the instrument's range of use.
■■ The operating instructions are part of the product and must be kept in the
immediate vicinity of the instrument and readily accessible to skilled personnel
at any time. Pass the operating instructions onto the next operator or owner of
the instrument.
■■ Skilled personnel must have carefully read and understood the operating
instructions prior to beginning any work.
■■ The general terms and conditions contained in the sales documentation shall
apply.
■■ Subject to technical modifications.
■■ Further information:
- Internet address:
www.wika.de / www.wika.com
- Application consultant:
Tel.: +49 9372 132-0
- Relevant data sheet:
AC 80.13
Fax: +49 9372 132-406
info@wika.de
14122699.02 10/2016 EN
EN
designed and manufactured using state-of-the-art technology. All components
are subject to stringent quality and environmental criteria during production. Our
management systems are certified to ISO 9001 and ISO 14001.
6
WIKA operating instructions digital indicator, model DI32-1
2. Design and function
2. Design and function
2.1 Overview
14122699.02 10/2016 EN





EN

Designation
[☼] key
Description


[▼] key

[▲] key
MIN memory is accessed
Changes lower limit values
Changes between parameters
Changes parameter values


Switch point display



Programming mode is accessed
Changes to a deeper parameter level
MAX memory is accessed
Changes lower limit values
Changes between parameters
Changes parameter values
Displays the status of the switching outputs
Mounting element with clamping
screws
Used for fixing
7-segment display
Displays measured values, program numbers or parameters
Product label
Contains product information
WIKA operating instructions digital indicator, model DI32-1
7
2. Design and function
Functions
■■ Retrieval of the MIN/MAX values
■■ Tare function
■■ Averaging function
■■ Adjustable switching thresholds
■■ Linearisation of the measuring input
2.3 Scope of delivery
■■ Digital indicator
■■ Sealing
■■ 2 mounting elements
■■ Operating instructions
Cross-check scope of delivery with delivery note.
14122699.02 10/2016 EN
EN
2.2 Description
The DI32-1 is a 4-digit digital indicator for the measurement of different measurement signals (voltage, current, temperature and frequency). The configuration is
made via three front keys. Password protection prevents unwanted changes to the
parameters.
With the two semiconductor switching outputs, limits can be monitored and
signalled to a control room. The electrical connections are made at the rear via
plug-in terminals.
8
WIKA operating instructions digital indicator, model DI32-1
3. Safety
3. Safety
3.1 Explanation of symbols
WARNING!
... indicates a potentially dangerous situation that can result in
serious injury or death, if not avoided.
EN
CAUTION!
... indicates a potentially dangerous situation that can result in light
injuries or damage to equipment or the environment, if not avoided.
Information
... points out useful tips, recommendations and information for
efficient and trouble-free operation.
3.2 Intended use
The DI32-1 digital indicator is designed for the evaluation and display of sensor
signals. With the switching outputs, it is possible to realise simple control functions.
The digital indicator is not permitted to be used in hazardous areas.
Only use the digital indicator in applications that lie within its technical performance limits (e.g. max. ambient temperature).
→ Performance limits see chapter 19 “Specifications”.
14122699.02 10/2016 EN
The instrument has been designed and built solely for the intended use described
here, and may only be used accordingly.
The manufacturer shall not be liable for claims of any type based on operation
contrary to the intended use.
WIKA operating instructions digital indicator, model DI32-1
9
3. Safety
3.3 Improper use
WARNING!
Injuries through improper use
Improper use of the instrument can lead to hazardous situations
and injuries.
▶▶ Refrain from unauthorised modifications to the instrument.
▶▶ Do not use the instrument within hazardous areas.
EN
Any use beyond or different to the intended use is considered as improper use.
3.4 Personnel qualification
WARNING!
Risk of injury should qualification be insufficient
Improper handling can result in considerable injury and damage to
equipment.
▶▶ The activities described in these operating instructions may
only be carried out by personnel who have the qualifications
described below.
14122699.02 10/2016 EN
Skilled electrical personnel
Skilled electrical personnel are understood to be personnel who, based on
their technical training, know-how and experience as well as their knowledge
of country-specific regulations, current standards and directives, are capable
of carrying out work on electrical systems and independently recognising and
avoiding potential hazards. The skilled electrical personnel have been specifically
trained for the work environment they are working in and know the relevant standards and regulations. The skilled electrical personnel must comply with current
legal accident prevention regulations.
10
WIKA operating instructions digital indicator, model DI32-1
3. Safety
3.5 Labelling, safety marks
Product label
The product label is located on the upper side of the digital indicator.
EN
WIKA Alexander Wiegand SE & Co. KG
63911 Klingenberg • Germany • www.wika.com
Digitalanzeige / Digital Indicator DI32-1
: 14110042
Bestell-Nr. / Order No.
: Multi-function
Eingang / Input
: DC 9...28 V
Hilfsenergie / Power Supply
Schaltpunkte / Switching Outputs : 2
Serial No.
DI32-1




Out 1: NPN, PNP
Out 2: NPN, PNP
GND
L+ / DC 9...28V
L- / GND
Power Outputs
supply
10V, PNP
GND, Pt100(0)
Input
50mV, TC, Pt100, Reset
1V, 2V, mA, Freq., Pt100(0)


9 8 7 6 5 4 3 2 1
Serial number
Model
Pin assignment
Symbols
14122699.02 10/2016 EN
Before mounting and commissioning the instrument, ensure you
read the operating instructions!
WIKA operating instructions digital indicator, model DI32-1
11
4. Transport, packaging and storage
4. Transport, packaging and storage
CAUTION!
Damage through improper transport
With improper transport, damage to property can occur.
▶▶ When unloading packed goods upon delivery as well as during
internal transport, proceed carefully and observe the symbols on
the packaging.
▶▶ With internal transport, observe the instructions in chapter 5.2
“Packaging and storage”.
4.2 Packaging and storage
Do not remove packaging until just before mounting.
Keep the packaging as it will provide optimum protection during transport (e.g.
change in installation site, sending for repair).
Permissible conditions at the place of storage:
■■ Storage temperature: -30 ... +70 °C
■■ Humidity: 0 ... 85 % relative humidity (no condensation)
Avoid exposure to the following factors:
■■ Direct sunlight or proximity to hot objects
■■ Mechanical vibration, mechanical shock (putting it down hard)
■■ Soot, vapour, dust and corrosive gases
Store the digital indicator in its original packaging in a location that fulfils the conditions listed above. If the original packaging is not available, pack and store the
instrument as described below:
1. Wrap the instrument in a plastic film.
2. Place the instrument, along with the shock-absorbent material, in the packaging.
12
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
4.1 Transport
Check the digital indicator for any damage that may have been caused by transport.
Obvious damage must be reported immediately.
5. Commissioning
5. Commissioning
If the instrument is transported from a cold into a warm environment, the formation
of condensation may result in instrument malfunction. Before putting it into operation, wait for the instrument temperature and the room temperature to equalise.
5.1 Requirements for the installation location
■■ In the vicinity there should be no magnetic or electrical fields, e.g. from transformers, radio-telephones or electrostatic discharges.
■■ In the vicinity there should be no strong heat sources. The permissible operating
temperature must not be exceeded (max. 50 °C).
5.2 Mounting
3,0
24,0
Dic
htu
ng
48
,0
14122699.02 10/2016 EN




lich
mm chließ mm
,0
52 eins e 67
fe mm
utie le
ba ssk
Ein schlu
An


Mounting element
Clamping screw
Sealing
Cutting out the control panel
■■ Control panel thickness max. 3 mm
■■ Panel cutout 45.0+0.6 x 22.2+0.3 mm
WIKA operating instructions digital indicator, model DI32-1
13
EN
5. Commissioning
Installing the digital indicator
1. Remove the mounting elements.
2. Slide the seal over the digital indicator.
4. Lock the mounting elements into place and tighten the clamping screws (max.
0.1 Nm).
5.3 Electrical connection
Notes on installation
■■ Protect the power supply with a slow fuse of max. 2 A.
■■ Route the signal input lines and signal output lines separately.
■■ Route outward and return lines side-by-side.
■■ Galvanically isolated potentials must be connected to a suitable point (e.g.
earth or plant ground).
■■ For high-accuracy requirements and small measurement signals, the sensor
wires must be shielded and twisted. The shield should be connected at one end
only to a suitable equipotential bonding (e.g. measurement ground).
■■ Avoid electrostatic discharges in the area of the terminals.
Terminal configuration
9-pin terminal block
Signal inputs
9
DC 1 V
DC 2 V
mA
Frequency
Pt100
Pt1000
8
50 mV
TC
Pt100
Reset
7
GND
Pt100
Pt1000
6
DC 10 V
Freq.PNP
Power supply
(not galvanically
isolated)
5
U-
4
U+
Switch points (not galvanically
isolated)
3
GND
2
OUT2
NPN
PNP
1
OUT1
NPN
PNP
→ For further information see chapter 19 “Specifications”
5.4 Switching on the digital indicator
▶▶ Connect the power supply.
» Segment test is carried out. Check the correct operation of all LEDs
» Software type and software version are displayed.
» Digital indicator is ready for operation.
14
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
3. Slide the digital indicator into the control panel from the front.
Check the seal is properly seated.
+
GND S2
2
1
S1
Semi-conductor
Switching
outputs points
supply
GND S2
6
S1
3
2
1
5
4
9-28
_ VDC
Voltage
Semi-conductor
9-28
VDC
+
_supply
outputs
1 VA
<
Switching points
GND S2
S1
Switching points
Switching points
Signal
SignalSignal
5 20
4mA3GND 2S2 1 S1
8 sensor,
6 4 ...
9
4-20
mA7
9-28
VDC
3-wire
GND S2
S1
Signal input
9
8
8
7
7
_
6
_
Voltage
Semi-conductor
3
2
1
5
4 + outputs
6 supply
3
2
1
5
4
_
+
_
+Switching
Switching
points
points
GND
GND
S2 S2 S1 S1
4-20 mA +
9-28 VDC
9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1
0/4-20 mA
9-28
_ VDC+
_ VDC
4-20 mA
9-28
+
_
Switching points
Signal
Signal
9
Switching points
Switching points
GND
GND
S2 S2 S1 S1
GNDpoints
S2
S1
Switching
5VDC
4 3 3 2 2 1 1
8mA7 mA
7 6 6 9-28
5 9-28
4 VDC
80/4-20
9 9 4-20
3 S22 S11
5
4 GND
8
7
6
9
_
_
+
_ + +
1/2
3
2
1
4
8 V 7 _ 6 105V
9
Switching points
_
_
+
Switching
GNDpoints
S2
S1
+
_ +
GND
S2
3-wire
sensor,
0 ...5 1/24 ...
10
V2 S11
3
8
7
6
9 0/4-20
9-28
VDC
4-20 mA+mA
9-28
VDC
0-1/2...10 V
9-28 VDC3
2
1
8 V 7
6
9
+
1/2
105 V _4
_ VDC+
0/4-20 mA _
9-28
Switching points
Signal
Signal
Signal Signal
Signal
Signal
+
_
Switching
GND S2points
S1
3
2
1
5 VDC
4
9-28
GND S2
S1
_4
2
1
5V VDC
8 V mA
7
6 10
9 0/4-20
9-28
+3
1/2
3
2
1
5_
4
8
7 _ 6
9
+
+Switching points
_ + 10 V _
1/2 V
_
GND S2
S1
+
0-1/2...10 V
9-28 VDC
+
3
2
1
5
4
8
7
6
9 0/4-20
mA
9-28
VDC
Signal
Signal
Signal
Signal
6
V
1/20-1/2...10
V
_ VDC+
10 V 9-28
_
Switching points
+
GND S2
S1
Signa
Signal
Signal
Signal
Switching points
_ _
GND
S2 S2 S1 S1
GND
+ +
GNDpoints
S2
S1
Switching
9-28
4 VDC
90/4-20
4 3 3 2 2 1 1
8 7 7 6 6 5 5
9 8 mA
0/4-209mAsensor,
9-28
VDC
3-wire
4
...
20
mA
GND
3 S22 S11
5
4
8 Transmitter
7
6
Transmitter
_ _ + +
supply
supply
_
with
supply
+3
1/2
2
1
4
8 V 7
6 105V
9 external
Switching points
_
+Switching
_ _
GNDpoints
S2
S1
+ +
_
+ _
GND S2
S1
0/4-20
mA
9-28
VDC
3
2
1
5
4
8
7
6
9
0/4-20
mA V
9-28
VDC
0-1/2...10
9-28
VDC
_
Transmitter
2
1
5V _4
8 V +Transmitter
7
6
9
+3
1/2
Transmitter
supply 109-28
supply
0/4-20 mA
_ VDC
supply
+
Switching points
Transmitter
Switching points
_
Switching
GNDpoints
S2
S1
supply
+ _
GND S2
S1
Switching
_
GND S2points
S1
0-1/2...10
9-28 VDC
3
2
1
5
4
8+V
7
6
9
GND
S2
S1
3
2
1
5
4
8
7
6
9
0/4-20
mA
Transmitter
9-28
VDC
_
3
2
1
5
4
8
7
6
9
+
1/2 V
supply 10 V _
507 mV
+3
2
1
4
8 VTransmitter
6 105V_
9 1/2
+
Switching points
supply
_
+
1/2 V
10
V
Switching
_
GNDpoints
S2
S1
+ _
GND S2
S1
_
0-1/2...10
V
9-28
VDC
3
2
1
5
4
8+
7
6
9
_
_
_
_
3-wire
sensor,
0 ... 1/2
... 10
V2 1
+
0/4-20
mA
VDC
8 V +50Transmitter
7 mV 6 1059-28
9
1/2
+3
V _4
0-1/2...10
V, supply
VDC
0-1/2...10
VTransmitter
9-28
VDC
with
external
supply
_ 9-28
+
1/2
Switching points
50V mV supply 10 V
Transmitter
Transmitter
Switching
GNDpoints
S2
S1
supply
supply
Switching
_
_
GND S2points
S1
3
2
1
5
4
8+ + 7 _ 6_
9
GND S2
S1
0-1/2...10
9-28 VDC
_4 VDC
2
1
8VV V,
90-1/2...10
507 mV 6
1/2
+3
105V 9-28
3
2
1
5_
4
7 Transmitter
6
9 50 8mVTransmitter
+
1/2 V
supply 10 V
supply
1/2 V 50 mV
+Switching points
10 V _
GND S2
S1
+ +_ _ _ _
0-1/2...10
VDC
2
1
59-28
4 VDC3
8 V V,7
6
90-1/2...10
9-28
_
50 mVTransmitter
_
+ Transmitter
1/2 V 50 mV
+
10 V _
supply
supply 9-28 VDC
0-1/2...10 V,
Switching points
50 mV
Transmitter
GND S2
S1
supply
9
8
+7
1/2 V
10 V
_
+
ignal
3 digital
2
1
5 VDC
4
0-1/2...10
V,
8 operating
7V
6 instructions
9 0-1/2...10
WIKA
indicator,
model
DI32-1
9-28
50 mV
1/2 V
l
14122699.02 10/2016 EN
Switching
GNDpoints
S2
S1
+
+
8
7V
9 0-1/2...10
Signal
Signal
SignalSignal
Switchpoint 1
GND
3
4
Voltage
3 outputs
2
1
6 _ 5supply4
+
9-28 VDC
_ 1 VA_
<
+
Voltage
Semi-conductor
Signal
Signal
5
Switching points
_
Signal Signal
Signal
Signal
8
7
4-20 mA
Signal input
9
9-28 VDC
_ 1 VA
<
Signal
Signal input
1
50 mV
Signal
Signal
Signal
Signal
7
2
outputs
Switchpoint 1
8
4
1 VA
<supply
+
Switchpoint 2
6
Signal input
3
5
_
GND
7
6
Switchpoint 2
7
10V, PNP (HTL)
8
9
Signal
9
8
GND, Pt100 (0)
9
1/2 V
Signal
Switchpoint 1
GND
Switchpoint 2
10V, PNP (HTL)10V, PNP (HTL)
1V, 2V,
mA, Frequency,
1V, 2V, mA, Frequency,
Pt100(0)
1V, 2V, mA,
Frequency, Pt100(0)
Pt100(0)
Signal
input
Voltage
9-28
VDC
2-wire
sensor,
4 ...
20
mASemi-conductor
_
Switching points
_
_ 10 V
+
+Switching points
GND S2
S1
GND S2
S1
+
_
3
2
1
5
4
8
7
6
9
0-1/2...10
+ 50 mV
3
2
1
5 9-28
8 mA 7V,
6
90/4-20
_4 VDC
9-28
VDC
+
2-wire
sensor,
4 ... _20
mA
Transmitter
+
10 V
1/2 V 50 mV
supply
Switching
points
with
external
0-1/2...10
V, 50 mVsupply
9-28 VDC
Switching
_
GNDpoints
S2
S1
_+
Switching
points
Switching
GND
S2points
S1
+
3GND 2S2 1 S1
5
4
8
7
6
9
0/4-20 mA
9-28 VDCGND
S2
S1
3
2
1
5
8
7 Transmitter
6
9
_4
+
7supply
0-1/2...10
50
5 _ 5VDC
4 +4 3 3 2 2 1 1
7 mV
610 6V 9-28
91/29V 8 508V,mV
_ _ + +
Switching
points
_
Switching
points
_+
GND
S2 S2 S1 S1
GND
+
_
0/4-20 mA +
9-28
VDC
_
9 9 8 8 + 7 Transmitter
7 6 6 5 5 4 4 3 3 2 2 1 1
0/4-20 mA
9-28 VDC
supply
0-1/2...10 V, 50 mV
9-28
_ VDC
_ + +
0/4-20 mA
Transmitter 9-28 VDC
Transmitter
supply
Switching
points
Switching
points
supply
5.5.1 Current and voltage measurement
+
Signal
Signal
3
2
1
5
4
8
7
6
9
3 S22 S11
5 _ VDC
4 GND
8
7 mV 6
9
0-1/2...10
50
+
10 V 9-28
1/2 V 50V,mV
_4
2
1
5
8
7
6
9
+3
Signal
supply
Switching points
Switching
GND S2points
S1
GNDpoints
S2
S1
Switching
Signal
2
1
Semi-conductor
outputs
_Voltage
1 VA
<
_
1
+
9-28 VDC
Signal
2
10 V
_
+
Signal
Signal
Signal
GND
3
4
GND
10V, PNP (HTL)
GND, Pt100 (0)
Signal input
50 mV
Signal
5
6
Switchpoint 1
7
_
+
5.5
Connection
examples
9-28 VDC
3
5
4
8
7
6
9
Switchpoint 1
8
Switchpoint 2
5. Commissioning
9
1/2 V
0-1/2...10 V, 50 mV
Switchpoint 2
10V, PNP (HTL) 1
GND, Pt100 (0) G
50mV, TC, Pt100, Reset
50mV, TC, Pt100,50mV,
Reset TC,
GND, Pt100 (0) GND, Pt100 (0)
1V, 2V, mA, Frequency,
1V, 2V,
1V, 2V,Pt100(0)
mA, Frequency,
mA, Frequ
Pt100(0)
50mV, TC, Pt100,
50mV, TC, Pt100, Reset
Reset
50mV,
TC, Pt100, Reset
_
9-28 VDC
_ 1 VA
<
50 mV
_
6_
5
4
_ VDC+
10 V 9-28
Transmitter
3
2
1
15
EN
GND S2
Signal
7
5
6
3
4
2
S1
8
9
1
Signal
5. Commissioning
_
8
9
+
7
_
5
6
1/2 V
Switching points
Switching points
Switching
GND points
S2
S1
1/28V
9
7
5
6
_4
6 10 5
V
507mV
1/2 V
_
10 V
GND S2
3
2
4
+3
2
GND S2
S1
1
8
9
1
Signal
EN
Signal
Signal
+
_ _
+
+
9-28
VDC
9-28
VDC
0-1/2...10 V,
50 mV
Switching points
GND S2
8
7
5
6
3
4
2
_
5.5.2 Temperature measurement
+
+
Pt100, 3-wire
0/4-20 mA
ts
9
Transmitter
supply
98
87
76
65
9
8
7
6
Pt100Pt100
S1
_
Signal
1
+
_
_
9-28 VDC
Transmitter
supply
S1
Pt1000, 2-wire
Switching
Switching
pointspoints
S1
_
+ 7
8
9
Signal
1
6
98
_
_
TC
IN
8
7
9
_
_
+
+
V 50 mV
TTL1/2TTL
Encoder
8
7
9Encoder
6
0-1/2...10_ V,
_
_
GND S2
3
4
5
65
_
54
_
+
32
43
2
21
S1
1
+
Pt1000
Pt1000
Switching points
S1
9-28 VDC
9-28 VDC
1
9
8
7
5
6
_
GND S2
3
4
2
S1
1
+
S1
2
9-28 VDC
1
Switching points
GND S2
3
4
2
S1
1
_ Switching
pointspoints
+ Switching
9-28 VDC GND S2
GND S2
S1 S1
32
21
1
54
43
Switching points
_ VDC
9-28
+
+
GND S2
S1
5
Switching
3
2 points
1
4
_
+
76
32
21
1
54
43
Switching
points
_
+
+ VDC
GND S2
S1
9-28
_
10 VVDC
9-28 VDC+
9-28
5Supply4
6Supply
IN
16
87
Pt1000
+
10 V _
9-28 VDC
9-28 VDC
+
GND GND
S2 S2
S1
98
9
S1
Switching points
7
Transmitter
supply
87
76
65
1
2
Switching points
9-28
_ VDC
+
GND GND
S2 S2
S1
TC
_
3
3
4
5
6
1
+ Switching points
TC
_
32
21
GND S2
+
4
8
Signal
IN
43
6
1/2 V
9
5
Switching
Switching
pointspoints
S1
Switching points
7
+
0-1/2...10 V
9
54
_
+
5
_
Transmitter
Pt100
supply
87
76
65
98
9
Thermocouple
_
_
+_
+
ts
1
S1
1
9-28 VDC
9-28 VDC
9-28 VDC
8
9
0/4-20 mA
S1
_
10 V
2
1
_
GND GND
S2 S2
S1
ts
3
4
Signal
r
5
6
1/2 V 50 mV
+
0-1/2...10
0-1/2...10V,V50 mV
9
7
GND S2
3
2
S1
1
+
WIKA
operating
Switching
points
Switching
points
9-28 VDC
GND S2
S1
Switching
Switching
pointspoints
GND GND
S2 S2
S1
98
9
IN
87
76
54
65
_
IN
43
_
+
32
21
S1
1
+
_
_
+
+
_
9-28 VDC
+ _ 9-28
TTL TTL +
VDC
Encoder
Encoder
5Supply
4
8
7
6 Supply
9
Sensor
Sensor
_
+
supplysupply
IN
14122699.02 10/2016 EN
Switchpoint 1
8
9
1
0-1/2...10sensor,
V
4-wire
0 ...9-28
1/2VDC
... 10 V,
Transmitter
50 mV, with
external supply
supply
+
4-wire sensor,
0 ... 1/2 ... 10 V, 50
9-28 VDC
mV0/4-20 mA
1
2
+
_
_
+
3
4
_
10 V
Switching points
GND S2
3
2
S1
1
instructions digital indicator, model
DI32-1
Switching
Switching
pointspoints
_
GND S2
S1
+
Pt100Pt100
87
76
65
GND GND
S2 S2
S1
5. Commissioning
98
54
GND GND
S2 S2
S1 S1
9-28 VDC
9-28 VDC
32
21
1
54
43
65
87
76
98
Encoder
with
TTL output
Switching
pointspoints
Switching
9
+
98
9
98
9
TC_ TC_
+
87
+
76
+ _ TC_
TC
87
76
_ VDC+
9-28
9-28
_ VDC
+
GND GND
S2 S2
S1
65
54
IN
TC
TC
_98
_
+ 87 + 76
TTL TTL
IN
IN Encoder
Encoder
9
87
76
98
_
_
+
+
TTL
TTL
IN
Encoder
Encoder
9
IN
Encoder
S1
_ + Switching
pointspoints
+ Switching
54
54
43
32
21
1
43
32
21
1
_
_+
+
9-28
VDC
9-28 VDC
Switching
pointspoints
Switching
SupplySupply
with PNP
output
GND GND
S2 S2
S1 S1
_
_
32
21
1
54
43
65
98 + 87 + 76
TTL TTL
9-28 VDC
9-28 VDC
_
_ + Switching
pointspoints
+ Switching
Encoder
Encoder IN IN Supply
Supply
GND GND
S2 S2
S1 S1
9
32
21
1
_98
54
43
_
65
+ 87 + 76
Switching
pointspoints
Switching
_ VDC
PNP PNP
9-28
9-28
_ VDC
+
+
IN Supply
S2 S2
S1 S1
Encoder
Encoder IN
SupplyGND GND
9
32
21
1
54
43
87
76
65
98
_
_
+
+
_
_+
9-28
VDC+
PNP PNP IN
IN 9-28 VDC
Switching
pointspoints
Switching
Encoder
Encoder
SupplySupply
GND GND
S2 S2
S1 S1
_
+_ +
32
21
1
54
43
87
76
65
9
98
PNP PNP
9-28 VDC
9-28 VDC
_
_ + Switching
pointspoints
+ Switching
Encoder
Supply
Encoder
Supply
IN IN
Encoder with NPN output
GND GND
S2 S2
S1 S1
9
9
_98
_
+ 87 + 76
NPN NPN
IN
Encoder
Encoder
9
87
76
98
_
_
+
+
IN
IN NPN NPN
14122699.02 10/2016 EN
IN
Encoder
Encoder
_
+_
+
NPN NPN
Encoder
Encoder
65
54
43
32
21
1
Switching
pointspoints
Switching
_ VDC
9-28
9-28
_ VDC
+
+
S2 S2
S1 S1
Supply
SupplyGND GND
65
54
Pt1000
Pt1000
76
65
54
43
_
_+
9-28
VDC+
9-28 VDC
SupplySupply
9-28 VDC
9-28 VDC
Supply
Supply
32
21
1
GND GND
S2 S2
S1
43
32
21
S1
1
_
_+
9-28
VDC+
9-28 VDC
Pt1000
Pt1000
measurement
9-28 VDC
9-28 VDC
Encoder with external supply and
TTL output
Switching
pointspoints
Switching
GND GND
S2 S2
S1
98
9
87
76
65
54
_
IN
IN
S1
Switching
pointspoints
Switching
_ VDC
9-28
9-28
_ VDC
+
+
S2 S2
S1 S1
Supply
SupplyGND GND
65
87
Switching
32 points
21 points
1
43 Switching
GND GND
S2 S2
S1
9-28 VDC
9-28 VDC
65
98
9
GND GND
S2 S2
S1 S1
_
_+
9-28
VDC+
9-28 VDC
32
21
1
54
43
65
_
IN
+
S1
Switching
pointspoints
Switching
32
21
1
43
GND GND
S2 S2
S1 S1
_
_+
9-28
VDC+
9-28 VDC
32
21
1
54
43
87
76
65
9
98
Pt100Pt100
_
_ + Switching
_
pointspoints
+ Frequency
+ Switching
+ _
5.5.3
and
rotational
speed
9
43
32
21
S1
1
_+ Switching
pointspoints
+ Switching
GND GND
S2 S2
S1
S1
32
21
1
54
43
_
65
+ 87 + 76
pointspoints
Switching
__ VDC
_ Switching
TTL TTL +
9-28
+ _ 9-28
+
+ VDC
IN
INEncoder
S2 S2
S1 S1
Supply
Encoder
SupplyGND GND
Sensor
Sensor
32
21
1
54
43
9
87
76supply
65
98
_ supply
_
+
+
_+
__ 9-28
+
VDC
+ _ 9-28
VDC
Switching
pointspoints
Switching
IN TTL
IN TTL +
Encoder
Encoder
SupplySupply
Encoder
with external
supply
and
GND GND
S2
S1 S1
S2
Sensor
Sensor
_
_
PNP
+ 76supply
32
21
1
54
43
65
9 output
98 + 87 supply
_ VDC
TTL TTL +
9-28 VDC
+ _ 9-28
_
_+ Switching
pointspoints
+ Switching
Encoder
Supply
Encoder IN IN
Supply
GND GND
S2 S2
S1 S1
Sensor
Sensor
supplysupply
32
21
1
_98 _87
54
43
65
9
+
+ 76
pointspoints
Switching
__ VDC
_ Switching
PNP PNP +
9-28
+ _ 9-28
+
+ VDC
IN
S2 S2
S1 S1
Encoder
Supply
Encoder IN
SupplyGND GND
9
_98
Sensor
Sensor
32
21
1
54
43
87
76supply
65
98
_ supply
_
+
+
_+
__ 9-28
+
_
VDC
PNP PNP + IN + IN
9-28
VDC
Switching
pointspoints
Switching
Encoder
Encoder
SupplySupply
GND GND
S2 S2
S1 S1
Sensor
Sensor
_
supply
+ _ supply
+
32
21
1
43
87
76 _ 65 _ 54
9
98
PNP PNP +
9-28 VDC
9-28 VDC
+
9
Encoder
Encoder
_
_+ Switching
pointspoints
Supply
+ Switching
Supply
IN IN
Encoder
with
external
supply
andS1
Sensor
Sensor
GND GND
S2 S2
NPN outputsupplysupply
3
2
S1
1
_
54
43
65
2
1
+ 87 + 76
pointspoints
Switching
__ VDC
_ Switching
9-28
+
+ _ 9-28
NPN NPN
+
+ VDC
IN
IN
S2 S2
S1 S1
Supply
SupplyGND GND
Encoder
Encoder
Sensor
Sensor
32
21
1
54
43
9
87
76supply
65
98
_ supply
_
+
+
_+
__ 9-28
+
VDC
+ _ 9-28
VDC
+
IN
INNPN NPN
9
_98
SupplySupply
Encoder
Encoder
Sensor
Sensor
_
supply
+_ supply
+
_ VDC
9-28 VDC
+
+ _ 9-28
NPN NPN
Supply
Supply
Encoder
Encoder
Sensor
Sensor
supplysupply
WIKA operating instructions digital indicator, model DI32-1
17
EN
5. Commissioning
Encoder with NPN output and
external resistor
Encoder with external supply, NPN
output and external resistor
Switching
pointspoints
Switching
GND GND
S2 S2
S1
87
76
65
_
9 IN 98
87
76
RV RV
8
76
9
IN9 IN_8 _ 7
+
+
RV RV
NPN
IN
IN
NPN
RV_ RV
+_ +
Encoder
Encoder
_NPN_NPN
+
+
Encoder
Encoder
NPN NPN
Encoder
Encoder
Encoder
65
65
43
_ 5_ + 4 +
3
4
32
21
1
_+
_
+
9-28 VDC
9-28 VDC
Voltage
Voltage
supplysupply
9-28 9-28
VDCVDC
Voltage
Voltage
9-28
VDC
9-28
VDC
supply
supply
Voltage
Voltage
with PNP
output
supply
supply
and
Switching
pointspoints
Switching
external resistor connection
GND GND
S2 S2
S1
S1
Switching
points
Switching
points
32
21
1
GND
S2
S1 S1
GND
S2
Switching
points
Switching
points
_
_+
+
IN
RV2 RV2
IN
3
2S2 2S2
1S1 1S1
9
3GND
54
4 GND
87
76
65
98
RV1 RV1
_
_
21
1
8 7 RV2
7 6RV2
98
9
IN 65IN 5 4 + 43+ 32
_
_
+
+
_+
_
+
RV1
IN VDC
RV1PNP
IN 9-28
RV2 RV2
PNP
9-28 VDC
_
Voltage
_
Voltage
RV1
+
RV1+Encoder
Encoder
supplysupply
9-28 9-28
VDCVDC
PNP
_
_+PNP
+
Voltage
Voltage
9-28
VDC
9-28
VDC
Encoder
Encoder
PNP PNP
supply
supply
Voltage
Voltage
Encoder
Encoder
supply
supply
98
9
87
76
65
54
GND GND
S2 S2
S1
Switching
points
Switching
points
32
21
1
GND
S2
S1 S1
GND
S2
Switching
points
Switching
points
_+
+
3
2S2 2S2
1S1 1S1
3GND
54
4 GND
54
43
98
9
87
76
65
76
65
_
IN
7
9 IN 98
RV RV8
S1
Switching
points
Switching
points
32
21
1
GND
S2
S1 S1
GND
S2
Switching
points
Switching
points
_+
+
3
2S2 2S2
1S1 1S1
3GND
54
4 GND
54
43
_ 5 _+ 4 + 3
21
1
8
76
65
3
2
4
IN 9 IN_98 _ 7
+
+
RV RV
_+
_
+
_
_ VDC
9-28
+
NPN
9-28 VDC
IN
IN
NPN +
RV_ RV
Voltage
_+
Voltage
+
Encoder
Encoder
supply
_supply
Sensor _
VDC
VDC
_ + + Sensor9-28 9-28
_NPNNPN
+
+ supply
supply Voltage
Voltage
_
9-28
VDC
Encoder
VDC
+ _ 9-28
Encoder
+
NPN NPN
supply
Sensor
Sensor supply
Voltage
supply
supply Voltagesupply,
Encoder
Encoder
Encoder
with
external
supply
Sensor supply
Sensor
Switching
pointspoints
Switching
supply
PNP outputsupply
and
external resistor
GND GND
S2 S2
S1 S1
connection
98
9
87
Switching
points
Switching
points
32
21
1
43
GND
S2
S1 S1
GND
S2
Switching
points
Switching
points
_+
+
3
2S2 2S2
1S1 1S1
3GND
4 GND
7 6IN 6 5IN 5 4
76
65
54
_
RV2
8
9
87
9RV2
_ 5 _+ 4 + 3
RV1 9RV1
87
76
65
3
2
4
8
9
IN IN
RV2 RV2 _
_
+ _ _+
+
+
_+
_
+
9-28
PNP
9-28 VDC
IN VDC
RV2 PNP
IN
RV2
RV1 RV1
_ +_
_
_Voltage
Voltage
+ +
+
Encoder
RV1
supplysupply
RV1Encoder
Sensor
9-28 9-28
VDCVDC
PNPPNP
_ Sensor
_
+_
+ _ supply
+ supply
+
Voltage
Voltage
Encoder
VDC
9-28 9-28
VDC
Encoder
PNP PNP
supply
Sensor
Sensor supply
Voltage
supply Voltage
Encoder supply
Encoder
supply
supply
Sensor
Sensor
supply
supply
21
1
5.5.4 Counter
Manual reset with external button
Switching
pointspoints
Switching
GND GND
S2 S2
S1
98
9
87
76
65
54
_
9
98
9
98
87
76
65
_+
54
S1
Switching
points
Switching
points
43
32
21
1
GND
S2
S1 S1
GND
S2
Switching
points
Switching
points
+
3
2S2 2S2
1S1 1S1
3GND
4 GND
_ 5_ + 4 +
8 7 Reset
7 6 Reset
65
3
4
_+
_
+
9-28 VDC
9-28 VDC
Reset
Reset
ResetReset
9-28 9-28
VDCVDC
32
21
1
Automatic reset with output 2 and
Switching
pointspoints
Switching
manual reset with external
button
GND GND
S2 S2
S1 S1
Switching
points
Switching
points
43
32
21
98
87
76
65
54
9
98
87
76
65
54
3
2S2 2S2
1S1 1S1
3GND
4 GND
9
98
8 7 Reset
7 6 Reset
65
54
43
9
32
21
Reset
Reset
ResetReset
9-28 9-28
VDC VDC
18
1
GND
S2
S1 S1
GND
S2
Switching
points
Switching
points
WIKA operating instructions digital indicator, model DI32-1
1
14122699.02 10/2016 EN
EN IN
98
9
Switching
pointspoints
Switching
S1
5. Commissioning
5.5.5 Switch points
NPN output, low side
S1
S1
S1
9
99
8
88
7
77
6
66
S2
S2
S2
EN
GND
GND
GND
3
5
4
5
33
5
44
_
+
__
++
2
22
1
11
X
XX
Relay
Relay
Relay
9-28 VDC
9-28VDC
VDC
9-28
PNP output, high side
L+
L+
L+
_
__
9
99
8
88
7
77
6
66
5
55
_
__
_
__
3
4
33
44
+
++
2
22
1
11
X
XX
RL
RR
LL
9-28 VDC
9-28VDC
VDC
9-28
Push-pull output, low side and
high side
L+
L+
L+
_
__
14122699.02 10/2016 EN
_
__
GND
GND
GND
9
99
8
88
7
77
6
66
5
55
_
__
3
4
33
44
+
++
9-28 VDC
9-28VDC
VDC
9-28
_
__
_
__
2
22
1
11
IN1
IN1 SPS
IN1
SPS
IN2 SPS
IN2
IN2
L+
L+
L+
GND
GND
GND
WIKA operating instructions digital indicator, model DI32-1
19
6. Operation
6. Operation
6.1 Key functions
Function
[▼] key
Accesses MIN memory (settable via programming).
Changes lower limit values (settable via programming).
Navigates downwards in the menu.
Lowers numerical values.
[☼] key
Programming mode is accessed.
Changes to a deeper menu level.
Settings confirmed.
[▲] key
Accesses MAX memory (settable via programming).
Changes lower limit values (settable via programming).
Navigates upwards in the menu.
Increases numerical values.
6.2 Menu navigation
meter
al *
[☼]
[☼]
[☼]
VOLT
[☼]
0 … 10
[▲]
[▼]
0…2
0…1
[▲] [▼]
0 … 50
[▲] [▼]
AMPE
[☼]
0 … 20
[▲]
[▼]
4 … 20
sende
igebereich *
End
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[☼]
0000 … 0.000
[☼]
-19.99 … 99.99
[☼]
-19.99 … 99.99
[▲] [▼]
sanfang
igebereich *
OFFS
[▲] [▼]
dot.A
stelle
[▲] [▼]
sende
al
sanfang
al
TYPE
EndA
[▲] [▼]
20
OFFA
[▲] [▼]
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
Key
6. Operation
6.3 Setting the numeric values
[☼]
Parameter
[☼]
1. Value
[☼]
[▲] [▼]
2. Value
[▲] [▼]
EN
[☼]
6.4 Accessing and exiting programming mode
Accessing
▶▶ Press [☼].
» “TYPE” will be shown in the display.
14122699.02 10/2016 EN
Exit
The digital indicator reverts to operating mode automatically after 10 seconds of
inactivity. The entered settings will be saved.
WIKA operating instructions digital indicator, model DI32-1
21
7. Voltage or current measurement
7. Voltage or current measurement
→ Complete menu tree from page 27
7.1 Selecting the input signal and measuring range
[☼]
[☼]
TYPE
VOLT
[☼]
[☼]
0 ... 10
[▲]
[▼]
0…2
0…1
[▲] [▼]
0 … 50
AMPE
[☼]
0 … 20
[▲]
[▼]
4 … 20
Parameter
Description
0-2
DC 0 ... 2 V
0 - 10
0-1
0 - 50
0 - 20
4 - 20
DC 0 ... 10 V
DC 0 ... 1 V
DC 0 ... 50 mV
0 ... 20 mA
4 ... 20 mA
14122699.02 10/2016 EN
EN
This chapter leads you through the parameters, step by step. Therefore, the
sub-chapters should be worked through in sequence. Dashed lines in the
diagrams indicate parameters that are skipped.
22
WIKA operating instructions digital indicator, model DI32-1
7. Voltage or current measurement
7.2 Setting the indication range
With this value pair, the measurement signal is assigned the desired indication
value.
[☼]
TYPE
EN
[▲] [▼]
End
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[▲] [▼]
OFFS
Parameter
Description
End
End of measuring range
OFFS
Start of measuring range
Setting range
-1999 ... 9999
-1999 ... 9999
7.3 Selecting the number of decimal places
Specifies the number of decimal places that are displayed on the screen. This
parameter has no influence on the scaling or the indication value.
[☼]
TYPE
[▲] [▼]
dot.A
[☼]
0000
[▲]
[▼]
000.0
00.00
14122699.02 10/2016 EN
0.000
WIKA operating instructions digital indicator, model DI32-1
23
7. Voltage or current measurement
7.4 Scaling the input signal
With this value pair, the start of the measuring range and the end of the measuring
range can be scaled. The measurement signal must not be applied.
[☼]
EN
TYPE
[▲] [▼]
EndA
[☼]
-19,99 … 99,99
[☼]
-19,99 … 99,99
[▲] [▼]
OFFA
Parameter
Description
EndA
End of measuring range
OFFA
Start of measuring range
Setting range
-19.99 ... 99.99
-19.99 ... 99.99
7.5 Setting the offset adjustment (TARE)
The characteristic curve of the input signal is shifted in parallel by the offset value.
[☼]
TYPE
[▲] [▼]
tArA
[☼]
-1999 … 9999
7.6 Setting the zero point suppression
A defined indication range is represented by 0000. With this function a fluctuating
indication of the zero point is avoided.
[☼]
TYPE
[▲] [▼]
ZErO
24
[☼]
00 … 99
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
Example: Parameter 10 = indication range -10 ... +10 is displayed as 0000.
7. Voltage or current measurement
7.7 Select the overrun and underrun behaviour
Overrun is indicated with 4 bars above.
Underrun is indicated with 4 bars below.
The exception to this is the 4 ... 20 mA input signal, where a measured value
smaller than 1 mA is already indicated as an underrun. This signalises a sensor
failure.
[☼]
EN
TYPE
[▲] [▼]
OVEr
[☼]
no
[▲]
[▼]
AdC
rAnG
5Pr
10Pr
Parameter
Description
AdC
With the display range being exceeded above or below the limits (dI.Lo/dI.HI),
over- or underrun will be displayed.
no
rAnG
5Pr
With the measuring range being exceeded above or below the limits (EnD/
OFFS), over- or underrun will be displayed. The indication range and transducer range are monitored additionally.
The input signal is monitored to ±5 % of the measuring range. The indication
range is also monitored.
The input signal is monitored to ±10 % of the measuring range. The indication
range is also monitored.
14122699.02 10/2016 EN
10Pr
If the indication range is left, the display will remain on the smallest value
(dI.Lo) or the highest value (dI.HI).
WIKA operating instructions digital indicator, model DI32-1
25
7. Voltage or current measurement
7.8 Linearising the sensor values
Parameter
Description
SPC.A
Number of programmable points
Setting range
0 ... 5
Setting analogue and indication values for programmable points
The value stored under “dIS” will be shown on the display, when it matches the
sensor signal defined under “InP”. The values must be parameterised in increasing
order.
Parameter
Description
Setting range
InP.1
Analogue value for programmable point 1
-1999 ... 9999
dIS.1
Indication value for programmable point 1
dIS.2
Indication value for programmable point 2
InP.2
Analogue value for programmable point 2
dIS.3
Indication value for programmable point 3
InP.3
Analogue value for programmable point 3
dIS.4
Indication value for programmable point 4
InP.4
Analogue value for programmable point 4
dIS.5
Indication value for programmable point 5
InP.5
[☼]
Analogue value for programmable point 4
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
TYPE
[▲] [▼]
SPC.A
[☼]
0…5
dIS.1
[☼]
-1999 … 9999
InP.1
[☼]
-1999 … 9999
dIS.5
[☼]
-1999 … 9999
InP.5
[☼]
-1999 … 9999
[▲] [▼]
[▲]
[▼]
26
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
Setting the number of programmable points
In addition to the lower and upper indication values, an additional 5 programmable
points can be defined. Only activated programmable point parameters will be
displayed (dIS.1 ... 5, InP.1 ... 5).
7. Voltage or current measurement
7.9 Menu tree
* Pflicht-Parameter
Eingangssignal *
[☼]
[☼]
TYPE
[☼]
VOLT
[☼]
0 … 10
[▲]
[▼]
0…2
EN
0…1
[▲] [▼]
0 … 50
[▲] [▼]
AMPE
[☼]
0 … 20
[▲]
[▼]
4 … 20
Messbereichsende
Display-Anzeigebereich *
End
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[☼]
0000 … 0.000
[☼]
-19.99 … 99.99
[☼]
-19.99 … 99.99
[☼]
-1999 … 9999
[☼]
00 … 99
[☼]
no
[▲] [▼]
Messbereichsanfang
Display-Anzeigebereich *
OFFS
[▲] [▼]
Nachkommastelle
dot.A
[▲] [▼]
Messbereichsende
Eingangssignal
EndA
[▲] [▼]
Messbereichsanfang
Eingangssignal
OFFA
[▲] [▼]
Offsetverschiebung
tArA
[▲] [▼]
Nullpunktunterdrückung
ZErO
[▲] [▼]
14122699.02 10/2016 EN
Über- und
Unterlaufverhalten
OUEr
[▲]
[▼]
AdC
rAnG
[▲] [▼]
5Pr
10Pr
Anzahl operating
Stützpunkte instructions SPC.A
[☼]
WIKA
digital indicator, model
DI32-1
0…5
27
rAnG
[▲] [▼]
7. Voltage or current measurement
5Pr
10Pr
Anzahl Stützpunkte
SPC.A
[☼]
0…5
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[☼]
-1999 … 999
[☼]
-1999 … 9999
[▲] [▼]
dIS.1
[▲] [▼]
Analogwert
Stützpunkt 1
InP.1
[▲] [▼]
Display-Anzeigewert
Stützpunkt 5
dIS.5
[▲] [▼]
Analogwert
Stützpunkt 5
InP.5
Allgemeine
Einstellungen
14122699.02 10/2016 EN
EN
Display-Anzeigewert
Stützpunkt 1
28
WIKA operating instructions digital indicator, model DI32-1
8. Temperature measurement
8. Temperature measurement
This chapter leads you through the parameters, step by step. Therefore, the
sub-chapters should be worked through in sequence. Dashed lines in the
diagrams indicate parameters that are skipped.
EN
→ Complete menu tree from page 31
8.1 Selecting measuring element and measuring range
[☼]
[☼]
TYPE
[P]
[☼]
VOLT
[▲] [▼]
Pt.SE
[☼]
Pt.Lo
[▲]
[▼]
Pt.Hi
[▲] [▼]
tHEr
Pt.tH
[☼]
tYP.L
[▲]
[▼]
tYP.J
tYP.K
tYP.B
tYP.S
tYP.N
tYP.E
tYP.T
14122699.02 10/2016 EN
tYP.R
Parameter
Description
Parameter
Description
Pt.Hi
Pt100 3-wire -200 ... +850 °C
tYP.S
Thermocouple type S
Pt.Lo
Pt.tH
tYP.L
tYP.J
tYP.K
Pt100 3-wire -50 ... +200 °C
Pt1000 2-wire -200 ... +850 °C
Thermocouple type L
Thermocouple type J
Thermocouple type K
tYP.B
tYP.N
tYP.E
tYP.T
tYP.R
WIKA operating instructions digital indicator, model DI32-1
Thermocouple type B
Thermocouple type N
Thermocouple type E
Thermocouple type T
Thermocouple type R
29
8. Temperature measurement
8.2 Select unit
[☼]
TYPE
[▲] [▼]
UnIt
EN
[☼]
°C
[▲]
[▼]
°F
8.3 Setting the impedance matching
With a temperature measurement, an error can occur as a result of the wire resistance. This measuring error can be corrected in the following ranges:
■■ Measurement in °C: -20.0 ... +20.0
■■ Measurement in °F: -36 ... +36
If the unit is changed under “Unlt”, the value under “OFFS” will be converted and
rounded.
[☼]
TYPE
[▲] [▼]
[☼]
-19,9 … 19,9 °C
-35,9 … 35,9 °F
14122699.02 10/2016 EN
OFFS
30
WIKA operating instructions digital indicator, model DI32-1
8. Temperature measurement
8.4 Menu tree
* Pflicht-Parameter
Messelement,
Messbereich *
[☼]
[☼]
TYPE
[☼]
VOLT
EN
AMPE
Pt.SE
[☼]
Pt.Lo
[▲]
[▼]
Pt.Hi
[▲] [▼]
tHEr
IMPu
[▲] [▼]
Pt.tH
[☼]
tYP.L
[▲]
[▼]
tYP.J
tYP.K
tYP.B
tYP.S
tYP.N
tYP.E
tYP.T
tYP.T
Einheit *
UnIt
[☼]
OFFS
[▲]
[▼]
°F
[▲] [▼]
Leitungsanpassung
°C
[☼]
-19.9 … 19.9 ( °C)
[▲]
[▼]
-35.9 … 35.9 (°F)
14122699.02 10/2016 EN
Allgemeine
Einstellungen
WIKA operating instructions digital indicator, model DI32-1
31
9. Frequency measurement
9. Frequency measurement
→ Complete menu tree from page 37
9.1 Selecting the input signal
[☼]
[☼]
TYPE
VOLT
[P]
[☼]
[▲] [▼]
IMPu
FrEQ
[☼]
9.2 Selecting triggering of the pulse input
[☼]
TYPE
[▲] [▼]
I.tYP
ttL
[☼]
[▲]
[▼]
nPn
PnP
Parameter
Description
nPn
Passive switch contact. Internal pull-up is switched.
ttL
PnP
Active TTL signals 0.8 ... 2 V
Active sensor output. Internal pull-down is switched.
14122699.02 10/2016 EN
EN
This chapter leads you through the parameters, step by step. Therefore, the
sub-chapters should be worked through in sequence. Dashed lines in the
diagrams indicate parameters that are skipped.
32
WIKA operating instructions digital indicator, model DI32-1
9. Frequency measurement
9.3 Select frequency range
[☼]
TYPE
[▲] [▼]
rAnG
[☼]
9.999
[▲]
[▼]
EN
99.99
999.9
9999
Parameter
Description
99.99
0 ... 99.99 Hz (automatic software filter at 500 Hz/5 ms)
9,999
999.9
0 ... 9.999 Hz (automatic software filter at 100 Hz/5 ms)
0 ... 999.9 Hz
9999
0 ... 9999 Hz (approximately 10 kHz)
9.4 Selecting pulse length limiting
Debounces mechanical contacts via the filter frequency.
[☼]
TYPE
[▲] [▼]
FILt
[☼]
no
[▲]
[▼]
2
500
Parameter
Description
2
2 Hz with a pulse-duty factor of 1:1 (minimum pulse length 250 ms)
14122699.02 10/2016 EN
no
5
10
20
50
100
500
No evaluation of the pulse length.
5 Hz with a pulse-duty factor of 1:1 (minimum pulse length 100 ms)
10 Hz with a pulse-duty factor of 1:1 (minimum pulse length 50 ms)
20 Hz with a pulse-duty factor of 1:1 (minimum pulse length 25 ms)
50 Hz with a pulse-duty factor of 1:1 (minimum pulse length 10 ms)
100 Hz with a pulse-duty factor of 1:1 (minimum pulse length 5 ms)
500 Hz with a pulse-duty factor of 1:1 (minimum pulse length 1 ms)
WIKA operating instructions digital indicator, model DI32-1
33
9. Frequency measurement
9.5 Setting the indication range
With this value pair, the measurement signal is assigned the desired indication
value.
[☼]
EN
TYPE
[▲] [▼]
End
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[▲] [▼]
OFFS
Parameter
Description
End
End of measuring range
OFFS
Start of measuring range
Setting range
-1999 ... 9999
-1999 ... 9999
9.6 Selecting the number of decimal places
Specifies the number of decimal places that are displayed on the screen. This
parameter has no influence on the scaling or the indication value.
[☼]
TYPE
[▲] [▼]
dot.F
[☼]
0000
[▲]
[▼]
000.0
00.00
14122699.02 10/2016 EN
0.000
34
WIKA operating instructions digital indicator, model DI32-1
9. Frequency measurement
9.7 Scaling the pulse signals
With this value pair, the start of the measuring range and the end of the measuring
range can be scaled. The measurement signal must not be applied.
[☼]
TYPE
EN
[▲] [▼]
End.F
[☼]
00.00 … 99.99
[☼]
00.00 … 99.99
[▲] [▼]
OFF.F
Parameter
Description
End.F
End of measuring range
OFF.F
Start of measuring range
Setting range
00.00 ... 99.99
00.00 ... 99.99
9.8 Setting the offset adjustment (TARE)
The characteristic curve of the input signal is shifted in parallel by the offset value.
[☼]
TYPE
[▲] [▼]
[☼]
-1999 … 9999
14122699.02 10/2016 EN
tArA
WIKA operating instructions digital indicator, model DI32-1
35
9. Frequency measurement
9.9 Linearising the sensor values
Parameter
Description
SPC.F
Number of programmable points
Setting range
0 ... 5
Setting analogue and indication values for programmable points
The value stored under “dIS” will be shown on the display, when it matches the
sensor signal defined under “InP”. The values must be parameterised in increasing
order.
Parameter
Description
Setting range
InP.1
Analogue value for programmable point 1
-1999 ... 9999
dIS.1
Indication value for programmable point 1
dIS.2
Indication value for programmable point 2
InP.2
Analogue value for programmable point 2
dIS.3
Indication value for programmable point 3
InP.3
Analogue value for programmable point 3
dIS.4
Indication value for programmable point 4
InP.4
Analogue value for programmable point 4
dIS.5
Indication value for programmable point 5
InP.5
[☼]
Analogue value for programmable point 4
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
-1999 ... 9999
TYPE
[▲] [▼]
SPC.F
[☼]
0…5
dIS.1
[☼]
-1999 … 9999
InP.1
[☼]
-1999 … 9999
dIS.5
[☼]
-1999 … 9999
InP.5
[☼]
-1999 … 9999
[▲] [▼]
[▲]
[▼]
36
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
Setting the number of programmable points
In addition to the lower and upper indication values, an additional 5 programmable
points can be defined. Only activated programmable point parameters will be
displayed (dIS.1 ... 5, InP.1 ... 5).
9. Frequency measurement
9.10 Menu tree
* Pflicht-Parameter
Eingangssignal *
[☼]
[☼]
TYPE
[☼]
VOLT
[▲] [▼]
[▲] [▼]
IMPu
[☼]
FrEQ
turn
Ansteuerung des
Impulseingangs *
I.tYP
[☼]
ttL
nPn
[▲] [▼]
Frequenzbereich *
rAnG
EN
[▲]
[▼]
[▲]
[▼]
PnP
[☼]
9.999
99.99
[▲]
[▼]
999.9
[▲] [▼]
9999
Impulslängenbegrenzung
FILt
[☼]
no
2
[▲]
[▼]
5
10
20
[▲] [▼]
50
100
14122699.02 10/2016 EN
200
500
Messbereichsende
Display-Anzeigebereich *
End
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[▲] [▼]
Messbereichsanfang
Display-Anzeigebereich *
OFFS
WIKA operating instructions digital indicator, model DI32-1
[▲] [▼]
37
200
9. Frequency measurement
Messbereichsende
Display-Anzeigebereich *
End
500
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[▲] [▼]
OFFS
[▲] [▼]
Nachkommastellen
dot.F
[☼]
0000
000.0
[▲]
[▼]
00.00
[▲] [▼]
0.000
Messbereichsende
Impulssignal
End.F
[☼]
00.00 … 99.99
[☼]
00.00 … 99.99
[☼]
-1999 … 999
[☼]
0…5
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[☼]
-1999 … 999
[☼]
-1999 … 9999
[▲] [▼]
Messbereichsanfang
Impulssignal
OFF.F
[▲] [▼]
Offsetverschiebung
tArA
[▲] [▼]
Anzahl Stützpunkte
SPC.F
[▲] [▼]
Display-Anzeigewert
Stützpunkt 1
dIS.1
[▲] [▼]
Analogwert
Stützpunkt 1
InP.1
[▲] [▼]
Display-Anzeigewert
Stützpunkt 5
dIS.5
[▲] [▼]
Analogwert
Stützpunkt 5
InP.5
Allgemeine
Einstellungen
38
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
Messbereichsanfang
Display-Anzeigebereich *
10. Rotational speed measurement
10.Rotational speed measurement
This chapter leads you through the parameters, step by step. Therefore, the
sub-chapters should be worked through in sequence. Dashed lines in the
diagrams indicate parameters that are skipped.
EN
→ Complete menu tree from page 42
10.1 Selecting the input signal
[☼]
[☼]
TYPE
VOLT
[☼]
[▲] [▼]
IMPu
turn
[☼]
10.2 Selecting triggering of the pulse input
[☼]
TYPE
[▲] [▼]
I.tYP
[☼]
ttL
[▲]
[▼]
nPn
PnP
Parameter
Description
nPn
Passive switch contact, which switches the internal pull-up to ground.
ttL
Active sensor output. In the indicator a pull-down is switched
14122699.02 10/2016 EN
PnP
Active TTL signals 0.8 ... 2 V
WIKA operating instructions digital indicator, model DI32-1
39
10. Rotational speed measurement
10.3 Selecting pulse length limiting
Debounces mechanical contacts via the filter frequency.
[☼]
TYPE
[▲] [▼]
EN
FILt
no
[☼]
[▲]
[▼]
2
500
Parameter
Description
2
2 Hz with a pulse-duty factor of 1:1 (minimum pulse length 250 ms)
no
No evaluation of the pulse length.
5
5 Hz with a pulse-duty factor of 1:1 (minimum pulse length 100 ms)
10
10 Hz with a pulse-duty factor of 1:1 (minimum pulse length 50 ms)
20
20 Hz with a pulse-duty factor of 1:1 (minimum pulse length 25 ms)
50
50 Hz with a pulse-duty factor of 1:1 (minimum pulse length 10 ms)
100
100 Hz with a pulse-duty factor of 1:1 (minimum pulse length 5 ms)
500
500 Hz with a pulse-duty factor of 1:1 (minimum pulse length 1 ms)
10.4 Setting pulses per rotation
[☼]
TYPE
[▲] [▼]
[☼]
0001 … 9999
14122699.02 10/2016 EN
PPt
40
WIKA operating instructions digital indicator, model DI32-1
10. Rotational speed measurement
10.5 Selecting the time base
[☼]
TYPE
[▲] [▼]
tIME
[☼]
SEC
EN
[▲]
[▼]
MIn
hour
Parameter
Description
MIn
Minute
SEC
Second
hour
Hour
10.6 Selecting the number of decimal places
Specifies the number of decimal places that are displayed on the screen. This
parameter has no influence on the scaling of the indication value.
[☼]
TYPE
[▲] [▼]
dot
[☼]
0000
[▲]
[▼]
000.0
00.00
14122699.02 10/2016 EN
0.000
WIKA operating instructions digital indicator, model DI32-1
41
10. Rotational speed measurement
10.7 Menu tree
* Pflicht-Parameter
Eingangssignal *
[☼]
[☼]
TYPE
[☼]
VOLT
[▲] [▼]
EN
[▲] [▼]
IMPu
[☼]
FrEQ
turn
Ansteuerung des
Impulseingangs *
I.tYP
[☼]
ttL
nPn
[▲] [▼]
Impulslängenbegrenzung
FILt
[▲]
[▼]
[▲]
[▼]
PnP
[☼]
no
2
[▲]
[▼]
5
10
20
[▲] [▼]
50
100
200
500
Impulse pro Umdrehung *
PPt
[☼]
0001 … 9999
[☼]
SEC
[▲] [▼]
tIME
MIn
[▲] [▼]
Nachkommastellen
dot
hour
[☼]
Allgemeine
Einstellungen
[▲]
[▼]
0000
000.0
[▲]
[▼]
00.00
0.000
42
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
Zeitbasis *
11. Up/Down counter
11. Up/Down counter
This chapter leads you through the parameters, step by step. Therefore, the
sub-chapters should be worked through in sequence. Dashed lines in the
diagrams indicate parameters that are skipped.
EN
→ Complete menu tree from page 47
11.1 Selecting an up or down counter
[P]
[☼]
TYPE
VOLT
[☼]
[▲] [▼]
IMPu
Co.up
[☼]
[▲]
[▼]
Co.dn
Parameter
Description
Co.dn
Down counter
Co.up
Up counter
11.2 Selecting triggering of the pulse input
[☼]
TYPE
[▲] [▼]
In.tY
[☼]
ttL
[▲]
[▼]
nPn
14122699.02 10/2016 EN
PnP
Parameter
Description
nPn
Passive switch contact, which switches the internal pull-up to ground
ttL
PnP
Active TTL signals 0.8 ... 2 V
Active sensor output. In the indicator one of the pull-downs is switched
WIKA operating instructions digital indicator, model DI32-1
43
11. Up/Down counter
11.3 Selecting the counter basis
As a basis for the counter, incoming pulses, seconds or minutes can be used. If
the counter basis of seconds or minutes is used, the counting is started or stopped
via the pulse input.
[☼]
TYPE
[▲] [▼]
Co.bA
PuLS
[☼]
[▲]
[▼]
SEC
MIn
Parameter
Description
SEC
Seconds
PuLS
MIn
Pulse
Minutes
11.4 Setting the edge control
The edge control is indicated when counting.
[☼]
TYPE
[▲] [▼]
EdGE
PoSI
[☼]
[▲]
[▼]
nEGA
Parameter
Description
nEGA
Negative edge
High signal = counter stops
Low signal = counter runs
PoSI
44
Positive edge
High signal = counter runs
Low signal = counter stops
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
11. Up/Down counter
11.5 Setting the prescaler
For numeric values that lie outside the indication range, a prescaler can be set.
The numerical value is divided by the prescaler, so that large numerical values can
be scaled onto the indication range.
Example: Prescaler = 1,000
The number 5,000,000 cannot be indicated on the display. Using the prescaler, the
number is divided by 1,000. On the display 5,000 will be shown.
[☼]
TYPE
[▲] [▼]
PrES
[☼]
0001 … 9999
11.6 Selecting pulse length limiting
Debounces mechanical contacts via the filter frequency.
[☼]
TYPE
[▲] [▼]
FILt
[☼]
no
[▲]
[▼]
2
500
Parameter
Description
2
2 Hz with a pulse-duty factor of 1:1 (minimum pulse length 250 ms)
no
5
14122699.02 10/2016 EN
10
20
50
100
500
No evaluation of the pulse length.
5 Hz with a pulse-duty factor of 1:1 (minimum pulse length 100 ms)
10 Hz with a pulse-duty factor of 1:1 (minimum pulse length 50 ms)
20 Hz with a pulse-duty factor of 1:1 (minimum pulse length 25 ms)
50 Hz with a pulse-duty factor of 1:1 (minimum pulse length 10 ms)
100 Hz with a pulse-duty factor of 1:1 (minimum pulse length 5 ms)
500 Hz with a pulse-duty factor of 1:1 (minimum pulse length 1 ms)
WIKA operating instructions digital indicator, model DI32-1
45
EN
11. Up/Down counter
11.7 Setting the upper indication value and upper pulse count value
The display is linearised freely via the prescaled pulse count. For this purpose, the
number of pulses required is assigned an indication value. The zero point cannot
be preselected.
For the absolute counter limit values, the settings of dI.HI and dI.Lo must be used
(see chapter 12 “General settings”).
[☼]
TYPE
[▲] [▼]
End
[☼]
-1999 … 9999
[☼]
0001 … 9999
[▲] [▼]
End.C
Parameter
Description
Setting range
End.C
Up counter: Upper pulse count value
Down counter: Lower pulse count value
0001 ... 9999
End
Up counter: Upper indication value
Down counter: Lower indication value
-1999 ... 9999
11.8 Selecting the number of decimal places
Specifies the number of decimal places that are displayed on the screen. This
parameter has no influence on the scaling or the indication value.
[☼]
TYPE
[▲] [▼]
dot
[☼]
0000
[▲]
[▼]
000.0
00.00
0.000
46
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
11. Up/Down counter
11.9 Menu tree
* Pflicht-Parameter
Auf-/Abwärtszähler * [☼]
[☼]
TYPE
[☼]
VOLT
EN
[▲] [▼]
[▲] [▼]
IMPu
[☼]
Co.up
[▲]
[▼]
Co.dn
Ansteuerung des
Impulseingangs *
In.tY
[☼]
ttL
[▲]
[▼]
nPn
[▲] [▼]
Zählerbasis*
Co.bA
PnP
[☼]
PuLS
[▲]
[▼]
SEC
[▲] [▼]
Flankensteuerung *
EdGE
MIn
[☼]
PrES
[▲]
[▼]
nEGA
[▲] [▼]
Vorteiler
PoSI
[☼]
0001 … 9999
[☼]
no
[▲] [▼]
Impulslängenbegrenzung
FILt
2
[▲]
[▼]
5
14122699.02 10/2016 EN
10
20
[▲] [▼]
50
100
200
WIKA operating instructions digital indicator, model DI32-1
500
47
[▲] [▼]
PrES
Vorteiler
11.
Up/Down counter
[☼]
0001 … 9999
[☼]
no
[▲] [▼]
Impulslängenbegrenzung
FILt
2
[▲]
[▼]
5
EN
10
20
[▲] [▼]
50
100
200
500
Display-Anzeigeendwert *
End
[☼]
-1999 … 9999
[☼]
0001 … 9999
[☼]
0000
[▲] [▼]
Impulszahl-Endwert *
End.C
[▲] [▼]
Nachkommastellen
dot
Allgemeine
Einstellungen
000.0
[▲]
[▼]
00.00
14122699.02 10/2016 EN
0.000
48
WIKA operating instructions digital indicator, model DI32-1
12. General settings
12. General settings
This chapter leads you through the parameters, step by step. Therefore, the
sub-chapters should be worked through in sequence. Dashed lines in the
diagrams indicate parameters that are skipped.
EN
→ Complete menu tree from page 52
12.1 Setting the measuring time
The measuring time defines in which cycle the measured value is recorded. Via
this function the display of the measured value can be settled.
[☼]
TYPE
[▲] [▼]
SEC
Parameter
SEC
[☼]
00.1 … 2.00
Description
0.01 ... 2.00 seconds
0.00 ... 2.00 seconds (with pulse measurement)
12.2 Setting the moving average determination
The display shows the moving average of the last 2 ... 20 measured values. There
is no weighting of the measured values.
[☼]
TYPE
[▲] [▼]
GLM
Parameter
1 … 20
Description
1 ... 20 (1 = moving average determination is deactivated)
14122699.02 10/2016 EN
GLM
[☼]
WIKA operating instructions digital indicator, model DI32-1
49
12. General settings
12.3 Limiting the indication range
For overrun evaluation, the measuring range and the overrun characteristics
(OVEr) are evaluated. In addition, this range can be further limited using the lower
indication value and the upper indication value.
[☼]
TYPE
[▲] [▼]
dI.HI
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[▲] [▼]
di.Lo
Parameter
Description
dI.HI
Upper indication value
dI.Lo
Lower indication value
Setting range
-1999 ... 9999
-1999 ... 9999
12.4 Assigning key functions
Here the [▲] [▼] keys can be assigned a key function.
[☼]
TYPE
[▲] [▼]
tASt
no
[☼]
[▲]
[▼]
EHtr
AL.LI
Parameter
Description
EHtr
Retrieval of the MIN/MAX values
no
AL.Li
50
No function
Limit value correction
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
12. General settings
12.5 Selecting display blinking
A blinking display can be set as an additional alarm function. As soon as the
switching threshold is reached, the display starts to blink.
[☼]
TYPE
EN
[▲] [▼]
FLAS
no
[☼]
[▲]
[▼]
AL-1
AL-2
AL.12
Parameter
Description
AL-1
First limit value
no
AL-2
Second limit value
Both limit values
14122699.02 10/2016 EN
AL.12
The display does not blink
WIKA operating instructions digital indicator, model DI32-1
51
12. General settings
12.6 Menu tree
[☼]
[▲] [▼]
Messzeit
SEC
[☼]
00.1 … 2.00
[☼]
1 … 20
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[☼]
no
[▲] [▼]
Gleitender Mittelwert
GLM
[▲] [▼]
Endwertdarstellung
dI.HI
[▲] [▼]
Anfangwertdarstellung
di.Lo
[▲] [▼]
Tastenfunktionen
tASt
[▲]
[▼]
EHtr
[▲] [▼]
Anzeigeblinken
FLAS
Schaltausgänge
AL.LI
[☼]
no
[▲]
[▼]
AL-1
AL-2
AL.12
52
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
TYPE
13. Switching outputs
13. Switching outputs
This chapter leads you through the parameters, step by step. Therefore, the
sub-chapters should be worked through in sequence. Dashed lines in the
diagrams indicate parameters that are skipped.
The menu navigation is arranged in such a sequence that first switching output 1
must be set and subsequently switching output 2. In the following sub-chapters the
parameters will all be described together since they behave in the same way and
are carried out in the same logical sequence.
→ Complete menu tree from page 57
13.1 Selecting the switching function
[☼]
TYPE
[▲] [▼]
A1.Fu
A2.Fu
[☼]
off
[▲]
[▼]
on
HI.LI
Lo.LI
rAnG
Out.r
Parameter
Description
on
The switching output is switched permanently in measuring mode
Only the parameters “Ax.Er” and “Ax.tY” can be set
14122699.02 10/2016 EN
oFF
HI.LI
Lo.LI
rAnG
Out.r
Switching output without function
There are no parameters that can be set
Switches when the switching threshold is exceeded
Switches when measured value drops below the switching threshold
Switches within the switching window (window function)
Switches outside of the switching window (window function)
WIKA operating instructions digital indicator, model DI32-1
53
EN
13. Switching outputs
13.2 Setting a switching window (window function)
These parameters are only selectable when the limit value properties “rAnG” or
“Out.r” are set (see chapter 13.1 “Selecting limit value properties”).
These parameters define the upper and lower limits of the switching range.
[☼]
TYPE
[▲] [▼]
A1.HI
A2.HI
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[▲] [▼]
A1.Lo
A2.Lo
Parameter
Description
A1.HI, A2.HI
Setting range
Upper limit value
A1.Lo, A2.Lo
-1999 ... 9999
Lower limit value
-1999 ... 9999
13.3 Selecting switch behaviour for limit value errors
Sets the switch behaviour in the event an instrument checksum is incorrect or the
indication range is transgressed.
[☼]
TYPE
[▲] [▼]
A1.Er
A2.Er
on
[☼]
[▲]
[▼]
oFF
no
Parameter
Description
oFF
The switching output behaviour is inverted. When an error occurs, the error
behaviour overrides the actual limit value function.
on
no
54
The selected switch behaviour is activated. In push-pull operation, HIGH/
U+ is switched.
A display overrun (> 9999) or underrun (< -1999) does not trigger any alarm.
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
13. Switching outputs
13.4 Selecting switch behaviour
[☼]
TYPE
[▲] [▼]
A1.tY
A2.tY
nPn
[☼]
EN
[▲]
[▼]
PnP
Ac.HI
Ac.HI
Parameter
Description
PnP
U+ is through connected (high side)
nPn
Ac.HI
GND is through connected (low side)
HIGH or U+ is through connected (push-pull)
Ac.Lo
LOW or GND is through connected (push-pull)
13.5 Setting the switching threshold
With the window function, this parameter is not requested.
[☼]
TYPE
[▲] [▼]
[☼]
-1999 … 9999
14122699.02 10/2016 EN
A1.L1
A2.L1
WIKA operating instructions digital indicator, model DI32-1
55
13. Switching outputs
13.6 Setting the hysteresis
The hysteresis is added to the switching threshold so that the switching of the
switching output is delayed. With the window function, this parameter is not
requested.
[☼]
TYPE
[▲] [▼]
A1.HY
A2.HY
[☼]
0000 … 9999
13.7 Setting the switch-off delay
The time value is reset when the instrument is restarted. On starting the instrument,
the alarm status is determined directly without the set delay being taken into account.
[☼]
TYPE
[▲] [▼]
A1.oF
A2.oF
[☼]
0000 … 5999
13.8 Setting the switch-on delay
The time value is reset when the instrument is restarted. On starting the instrument,
the alarm status is determined directly without the set delay being taken into account.
[☼]
TYPE
[▲] [▼]
A1.on
A2.on
[☼]
0000 … 5999
14122699.02 10/2016 EN
EN
56
WIKA operating instructions digital indicator, model DI32-1
13. Switching outputs
13.9 Menu tree
[☼]
TYPE
[▲] [▼]
Grenzwertverhalten
Schaltausgang 1
A1.Fu
[☼]
off
EN
[▲]
[▼]
on
HI.LI
Lo.LI
[▲] [▼]
rAnG
Out.r
Oberer Grenzwert
Schaltausgang 1
A1.HI
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[☼]
on
[▲] [▼]
Unterer Grenzwert
Schaltausgang 1
Meldung bei
Grenzwertfehler
Schaltausgang 1
A1.Lo
[▲] [▼]
A1.Er
[▲]
[▼]
oFF
[▲] [▼]
Schaltverhalten
Schaltausgang 1
A1.tY
no
[☼]
nPn
[▲]
[▼]
14122699.02 10/2016 EN
PnP
Ac.HI
[▲] [▼]
Ac.HI
Schaltschwelle
Schaltausgang 1
A1.L1
[▲] [▼]
[☼]
WIKA operating instructions digital indicator, model DI32-1
Hysterese
-1999 … 9999
57
13. Switching outputs
Schaltschwelle
Schaltausgang 1
Ac.HI
[▲] [▼]
Ac.HI
A1.L1
[☼]
-1999 … 9999
[☼]
0000 … 9999
[☼]
0000 … 5999
[☼]
0000 … 5999
[☼]
off
[▲] [▼]
A1.HY
[▲] [▼]
Ausschaltverzögerung
Schaltausgang 1
A1.oF
[▲] [▼]
Einschaltverzögerung
Schaltausgang 1
A1.on
[▲] [▼]
Grenzwertverhalten
Schaltausgang 2
A2.Fu
[▲]
[▼]
on
HI.LI
Lo.LI
[▲] [▼]
rAnG
Out.r
Oberer Grenzwert
Schaltausgang 2
A2.HI
[☼]
-1999 … 9999
[☼]
-1999 … 9999
[☼]
on
[▲] [▼]
Unterer Grenzwert
Schaltausgang 2
A2.Lo
[▲] [▼]
Meldung bei
Grenzwertfehler
Schaltausgang 2
A2.Er
oFF
[▲] [▼]
Schaltverhalten
Schaltausgang 2
58
[▲]
[▼]
A2.tY
no
[☼]
nPn
[▲]
[▼]
WIKA operating instructions digital indicator, model DI32-1
PnP
14122699.02 10/2016 EN
EN
Hysterese
Schaltausgang 1
[▲] [▼]
Unterer Grenzwert
13.
Switching
Schaltausgang
2 outputs
A2.Lo
[☼]
-1999 … 9999
[☼]
on
[▲] [▼]
Meldung bei
Grenzwertfehler
Schaltausgang 2
A2.Er
oFF
[▲] [▼]
Schaltverhalten
Schaltausgang 2
[▲]
[▼]
A2.tY
no
[☼]
nPn
EN
[▲]
[▼]
PnP
Ac.HI
[▲] [▼]
Ac.HI
Schaltschwelle
Schaltausgang 2
A2.L1
[☼]
-1999 … 9999
[☼]
0000 … 9999
[☼]
0000 … 5999
[☼]
0000 … 5999
[▲] [▼]
Hysterese
Schaltausgang 2
A2.HY
[▲] [▼]
Ausschaltverzögerung
Schaltausgang 2
A2.oF
[▲] [▼]
Einschaltverzögerung
Schaltausgang 2
A2.on
14122699.02 10/2016 EN
Passwortschutz
WIKA operating instructions digital indicator, model DI32-1
59
14. Password protection
14. Password protection
14.1 Setting the password
TYPE
[▲] [▼]
CodE
[☼]
0000 … 9999
14.2 Activating/deactivating the password protection
When the password protection is activated, the keypad is locked.
[☼]
TYPE
[▲] [▼]
run
LOC
[☼]
[▲]
[▼]
ULoC
Parameter
Description
ULoC
Password protection deactivated
LOC
Password protection activated
Unlocking the keypad
1. Press the [☼] key for 3 seconds.
» Password entry appears.
2. Enter the password using [▲] [▼] and confirm with [☼].
» Incorrect entry will be indicated with “FAIL”.
» Keypad is unlocked.
14122699.02 10/2016 EN
EN
[☼]
60
WIKA operating instructions digital indicator, model DI32-1
14. Password protection
14.3 Menu tree
[☼]
TYPE
[▲] [▼]
Passwort
CodE
[☼]
0000 … 9999
[☼]
LOC
EN
[▲] [▼]
Passwortschutz
aktivieren/deaktivieren
run
[▲]
[▼]
ULoC
14122699.02 10/2016 EN
[▲] [▼]
WIKA operating instructions digital indicator, model DI32-1
61
15. Factory settings
15. Factory settings
All application-specific data will be lost.
EN
With the reset, the factory settings will be loaded and used for subsequent
operation.
15.1 Restoring factory settings
1. Disconnect the digital indicator from the power.
2. Hold down the [☼] key and switch on the power supply until “----” appears.
» The factory settings are restored.
15.2 Overview of the factory settings
Parameter
Default
A1.Fu
oFF
A1.HI
A1.HY
A1.LI
A1.Lo
A1.oF
A1.on
A1.tY
A2.Er
A2.Fu
A2.HI
A2.HY
A2.LI
A2.Lo
A2.oF
A2.on
A2.tY
AMPE
62
no
200
0
100
100
0
0
nPn
no
oFF
400
0
300
14122699.02 10/2016 EN
A1.Er
300
0
0
nPn
0 ... 20
WIKA operating instructions digital indicator, model DI32-1
15. Factory settings
Parameter
Default
CodE
1234
Co.bA
dI.HI
dI.Lo
dot
dot.A
dot.F
EdGE
End
End.C
EndA
End.F
FILt
FLAS
I.tYP
In.tY
OFFA
OFF.F
OFFS
OVEr
PPt
PrES
Pt.SE
rAnG
run
SEC
SPC.A
SPC.F
tArA
14122699.02 10/2016 EN
tASt
tHEr
tIME
UnIt
VolT
ZErO
PuLS
-1999
9999
EN
0
0
0
PoSI
1000
1001
10
1000
no
no
ttL
ttL
0
0
0
no
1
1
Pt.Lo
9999
ULOC
1
0
0
0
no
tYP.l
MIn
°C
0 ... 10
0
WIKA operating instructions digital indicator, model DI32-1
63
16. Faults
16. Faults
Faults
Permanent underrun
4 bars below
LBR is displayed
help is displayed
Settings for measuring input not
available
Causes
Measures
Input signal too high
Check the measuring path
Not all programmable points are
parameterised
Check the parameters
Indication range or predefined
measuring range
is exceeded
Check the programmable
points, input types and signal
range
Input signal too small
Check the measuring path
Not all programmable points are
parameterised
Check the parameters
Indication range or predefined
measuring range
has been overrun at the low end
Cable break at the sensor,
incorrect connection of the
sensor (no connection to the
terminal)
Error in the configuration
memory
Password protection active
Check the programmable
points, input types and signal
range
Check the input type
Check the cabling
Restore factory settings
Deactivating the password
protection
Err 1 is displayed
---
With thermocouples there are
constant, higher measuring
deviations
Sources of heat or cold in
the direct vicinity
Remove sources of heat or cold
---
Correct deviations through
offset shift
Heating through high switching
currents
Return the digital indicator to the
manufacturer.
Reduce switching current
< 10 mA
14122699.02 10/2016 EN
EN
Permanent overrun
4 bars above
64
WIKA operating instructions digital indicator, model DI32-1
17. Maintenance and cleaning
17. Maintenance and cleaning
17.1 Maintenance
The digital indicator is maintenance-free.
Repairs must only be carried out by the manufacturer.
EN
17.2 Cleaning
When cleaning the front, note the following:
■■ The ingress protection of the front is IP 65 (protected against jet and splash
water).
■■ Use a damp cloth.
■■ Do not use any aggressive cleaning agents.
■■ Do not use any pointed and hard objects for cleaning.
14122699.02 10/2016 EN
When cleaning the rear, note the following:
■■ The ingress protection of the rear is IP 00 (no protection).
■■ Disconnect the digital indicator from the power.
■■ Use a damp cloth. Allow the digital indicator to dry before operating it again.
■■ Do not use any aggressive cleaning agents.
■■ Do not use any pointed and hard objects for cleaning.
WIKA operating instructions digital indicator, model DI32-1
65
18. Dismounting, return and disposal
18. Dismounting, return and disposal
18.1 Dismounting
1. Disconnect the digital indicator from the power.
2. Disconnect the cabling to the digital indicator or pull off the terminal blocks.
3. Loosen the clamping screws and take off the mounting elements.
4. Pull the digital indicator and seal out of the panel cutout.
5. Click the mounting elements back into place.
18.2 Return
Strictly observe the following when shipping the instrument:
All instruments delivered to WIKA must be free from any kind of hazardous
substances (acids, bases, solutions, etc.).
When returning the instrument, use the original packaging or a suitable transport
packaging.
To avoid damage:
1. Wrap the instrument in a plastic film.
2. Place the instrument, along with the shock-absorbent material, in the packaging.
Information on returns can be found under the heading “Service” on
our local website.
18.3 Disposal
Incorrect disposal can put the environment at risk.
Dispose of instrument components and packaging materials in an environmentally compatible way and in accordance with the country-specific waste disposal
regulations.
66
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
Digital indicator for panel mounting
19. Specifications
19. Specifications
Specifications
Display
■■ Principle
7-segment LED, red, 4-digit
■■ Indication range
-1999 ... 9999
■■ Character size
Input
■■ Number and type
■■ Input signals
1 multi-function input
Measuring ranges, resolutions, Ri see following table (Input
signals)
■■
■■
■■
■■
■■
■■
■■
■■
■■
■■
■■
■■
■■
■■
■■ Input configuration
Switching outputs
■■ Number and type
■■ Switch behaviour
Voltage supply
■■ Power supply
■■ Power consumption
Case
14122699.02 10/2016 EN
■■ Material
■■ Ingress protection (per IEC 60529 /
EN 60529)
■■ Weight
■■ Panel cut out
■■ Mounting
■■ Dimensions
EN
10 mm
Voltage
Current
Pt100
Pt1000
Thermocouple K
Thermocouple S
Thermocouple N
Thermocouple J
Thermocouple T
Frequency
Frequency, NPN
Frequency, PNP
Speed
Counter
Selectable via terminal connections and menu-driven
programming
2 semiconductor switching outputs, not galvanically isolated
Low side, NPN: max. DC 28 V, 100 mA
High side, PNP: U+ - 3 V, 100 mA
DC 9 ... 28 V, not galvanically isolated
≤1W
PC polycarbonate, black, UL94V-0
Sealing material: EPDM, 65 Shore, black
Front: IP 65
Rear: IP 00
approx. 100 g
45.0+0.6 x 22.2+0.3 mm
Screw-type mounting brackets for wall thicknesses to 5 mm
48 x 24 x 67 mm (incl. plug-in terminal)
WIKA operating instructions digital indicator, model DI32-1
67
19. Specifications
Specifications
Operating conditions
■■ Permissible ambient conditions
■■ Humidity
Accuracy data
0 ... 85 % r. h. annual mean without condensation
■■ Measuring error
see page 77
■■ Measuring time
0.1 ... 20.0 seconds, adjustable
■■ Temperature drift
■■ Measuring rate
Memory
Electrical connection
CE conformity
■■ EMC directive
100 ppm/K
approx. 1/s for temperature sensors
approx. 100/s for standard signals
EEPROM, data preservation ≥ 100 years (at 25 °C)
Removable plug-in terminal, 9-pin
Wire cross-section up to 1.5 mm²
2004/108/EC, EN 61326-1, emission (group 1, class B)
and interference immunity (industrial application)
14122699.02 10/2016 EN
EN
Operation: -20 ... +50 °C
Storage: -30 ... +70 °C
68
WIKA operating instructions digital indicator, model DI32-1
19. Specifications
Input signal
Measuring range Resolution
Voltage
0 ... 10 V (Ri > 100 kΩ)
Voltage
0 ... 1 V (Ri > 10 kΩ)
Current
4 ... 20 mA
Voltage
Voltage
Current
Pt100, 3-wire
Pt100, 3-wire
Pt1000, 2-wire
Thermocouple K
Thermocouple S
Thermocouple N
Thermocouple J
Thermocouple T
Thermocouple R
Thermocouple B
Thermocouple E
Thermocouple L
Frequency
Frequency, NPN
Frequency, PNP
Speed
Counter
0 ... 2 V (Ri > 10 kΩ)
0 ... 50 mV (Ri > 10 kΩ)
0 ... 20 mA
≥ 14 bit
≥ 14 bit
≥ 14 bit
0.1 °C / 0.1 °F
-200 ... +850 °C
1 °C / 1°F
-270 ... +1,350 °C
-50 ... +1,750 °C
-270 ... +1,300 °C
-170 ... +950 °C
-270 ... +400 °C
-50 ... +1,768 °C
+80 ... +1,820 °C
-270 ... +1,000 °C
-200 ... +900 °C
0 ... 10 kHz
0 ... 3 kHz
0 ... 1 kHz
0 ... 9,999 1/min
0 ... 9,999
( Prescaler up to 1,000)
0.2 % ± 1 digit
0.2 % ± 1 digit
EN
0.2 % ± 1 digit
0.2 % ± 1 digit
0.2 % ± 1 digit
-50 ... +200 °C
-200 ... +850 °C
Measuring error in
% of the measuring
range 1)
1 °C / 1°F
1 °C / 1°F
1 °C / 1°F
1 °C / 1°F
1 °C / 1°F
1 °C / 1°F
1 °C / 1°F
1 °C / 1°F
1 °C / 1°F
1 °C / 1°F
0.001 Hz
0.2 % ± 1 digit
0.5 % ± 1 digit
0.5 % ± 1 digit
0.5 % ± 1 digit
0.3 % ± 1 digit
0.3 % ± 1 digit
0.3 % ± 1 digit
0.3 % ± 1 digit
0.3 % ± 1 digit
0.3 % ± 1 digit
0.3 % ± 1 digit
0.3 % ± 1 digit
0.3 % ± 1 digit
0.001 Hz
0.001 Hz
0.001 1/min
14122699.02 10/2016 EN
1) Measuring error valid for measuring time of 1 second
WIKA operating instructions digital indicator, model DI32-1
69
Appendix: EC declaration of conformity
14122699.02 10/2016 EN
EN
70
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
EN
WIKA operating instructions digital indicator, model DI32-1
71
WIKA Alexander Wiegand SE & Co. KG
Alexander-Wiegand-Straße 30
63911 Klingenberg • Germany
Tel.+49 9372 132-0
Fax+49 9372 132-406
info@wika.de
www.wika.de
72
WIKA operating instructions digital indicator, model DI32-1
14122699.02 10/2016 EN
WIKA subsidiaries worldwide can be found online at www.wika.com.
Download PDF
Similar pages