Symphony Plus™ 110 Series Ice and Water Dispensers

Symphony Plus™ 110 Series
Ice and Water Dispensers
Installation, Operation and Service Manual
110CT425A/W
110CR425A/W
110FB425A/W
Following installation, please forward this manual
to the appropriate operations person.
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Order parts online:
www.follettice.com
01033729R03
Contents
Welcome to Follett. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before you begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Ambient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Ventilation clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Approximate shipping weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Before you begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing freestanding dispensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing countertop dispensers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing RIDE ice machines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing top mount ice machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
User information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How the dispenser works. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How SensorSAFE infrared dispensing works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Quiet Night™/Sleep cycle (does not apply to CR units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning/descaling and sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Weekly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Monthly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Semi-Annually (more often if conditions dictate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Ice Machine and Dispenser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Dispenser only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Lever models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SensorSAFE models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Wiring diagram - Lever. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Wiring diagram - SensorSAFE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Dispenser troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lever model troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SensorSAFE model troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Disassembly and replacement instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Ice transport tube replacement – Top mount units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Ice transport tube replacement – Freestanding and RIDE models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Thermostat replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Replacement parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Dispenser exterior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Wheelmotor and drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Dispense chute and splash panel (models with lever dispensing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Dispense chute and splash panel (models with SensorSAFE infrared dispensing). . . . . . . . . . . . . . . . . . . . . . 28
Electrical components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Hopper components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Ice transport tubing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chilled water components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Dispenser plumbing connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Solenoid dispense assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Water treatment accessories for Symphony Plus ice and water dispensers. . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2
100CR/CT/FB Ice and Water Dispensers
Welcome to Follett
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding
after-the-sale support. To ensure that this equipment delivers that same degree of service, we ask that you take
a moment to review the installation portion of this manual before beginning to install the unit. Our installation
instructions are designed to help you achieve a trouble-free installation. Should you have any questions or require
technical help at any point, please call our technical service group at (877) 612-5086 or
(610) 252-7301.
Note: To expedite assistance, all correspondence or communication MUST include the model number, serial
number and complete and detailed explanation of the problem.
Before you begin
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If
damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the filing
of a claim, if necessary.
Check your paperwork to determine which model you have. Follett model numbers are designed to provide
information about the type and capacity of Follett ice dispensing equipment. Following is an explanation of the
different model numbers.
110CT425A-L
L = Lever dispensing, S = SensorSAFE infrared dispensing
Condenser type – A = air-cooled, W = water-cooled
Ice machine capacity and refrigerant – 425 = 425 lbs (193 kg)/day, R404a refrigerant
Ice machine location – R = RIDE ice machine, T = integral ice machine in top of cabinet,
B = ice machine in base of freestanding units
Approximate storage capacity in lbs
CAUTION!
§§ Do not tilt any unit further than 30° off vertical during uncrating or installation.
§§ Dispenser bin area contains mechanical, moving parts. Keep hands and arms clear of this area at all times. If
access to this area is required, power to unit must be disconnected first.
§§ Follett recommends a Follett water filter system be installed in the ice machine inlet water line (standard capacity
#00130229, high capacity #00978957, carbonless high capacity #01050442).
§§ Prior to operation clean and sanitize the dispenser in accordance with instructions found in this manual.
§§ Ice is slippery. Be sure counters and floors around dispenser are clean, dry and free of ice.
§§ Do not block right side air intake or top air exhaust.
100CR/CT/FB Ice and Water Dispensers
3
Specifications
Electrical
§§ Models with RIDE ice machines (110CR425A/W). Ice machine and dispenser require their own separate,
dedicated circuit.
Basic electrical: 115 V/60 Hz/1 phase
Dispenser with
ice machine
Max.
circuit
Dispenser without
ice machine
Max.
circuit
11.0A
20A
4.0A
20A
§§ Freestanding models (110FB425A/W, 110CT425A/W) require a dedicated circuit.
Basic electrical: 115 V/60 Hz/1 phase
Total system
Max. circuit
11.0A
20A
§§ Dispensers and RIDE ice machines are supplied with 7-foot power cord with NEMA 5-15 hospital-grade plug.
Connect to a dedicated 15A circuit.
CAUTION!
All field wiring must be installed in accordance with NEC and local electrical codes. Field wiring diagram is
intended only to aid electrician or technician in understanding how equipment works.
Model
Electrical connection
Circuits required
110FB425A/W
cord & plug provided
115/60/1, 15A max. fuse size
110CT425A/W
cord & plug provided
115/60/1, 15A max. fuse size
110CR425A/W
cord & plug provided
115/60/1
Dispenser: 15A max. fuse size,
Ice machine: 15A max. fuse size
Ambient
Air temp*
100 F/38 C Max.
50 F/10 C Min. (Best performance below 80 F/27 C)
Water temp
90 F/32 C Max.
45 F/7.2 C Min. (Best performance below 70 F/21 C)
Water pressure
70 P.S.I./5Bar Max.
10 P.S.I./0.7 Bar Min.
†
*
†
Ambient air temperature is measured at the air-cooled condenser coil inlet.
Ambient water temperature is measured in the ice machine reservoir.
Plumbing
110CR with RIDE ice
machine
110CT with integral
ice machine
110FB with ice
machine in base
Dispenser drain
3/4" MPT
3/4" MPT
3/4" MPT
Ice machine drain
3/4" MPT
3/4 MPT
3/4" MPT
Dispenser water inlet
3/8" FPT
3/8" FPT
3/8" FPT
Ice machine water inlet
—
3/8" FPT
—
RIDE IM water inlet
3/8" FPT
—
—
Cond. inlet – w/c only
3/8" FPT
3/8" FPT
3/8" FPT
Cond. drain – w/c only
3/8" FPT
3/8" FPT
3/8" FPT
Note: Water shut-off recommended within 10 ft (3 m) of dispenser. Drain to be hard-piped and insulated. Maintain at
least 1/4" per foot (20 mm per 1 m) run of slope.
4
100CR/CT/FB Ice and Water Dispensers
Ventilation clearances
§§ No clearance required for countertop models with RIDE ice machine (110CR425A/W).
Note: 12" (30.5 cm) at top advised for service.
§§ 6" (15.2 cm) required at top (110CT425A/W).
Note: 6" (15.2 cm) at each side advised for service.
§§ 4" (10.2 cm) required at rear (110FB425A/W).
Note: 12" (30.5 cm) at top advised for service.
Approximate shipping weight
§§ 290 lb (132 kg), base stand: 140 lb (64 kg)
Installation
Before you begin
§§ All dispensers must be installed level in both directions to ensure proper operation.
§§ All countertop dispensers provide the option of taking utilities out the bottom or back of the dispenser.
See counter cut-out (Fig. 2) for bottom exiting utilities on units with and without drain pans. For installations
where utilities will exit through back of dispenser, refer to back view drawings.
§§ SensorSAFE dispensers are shipped with a plastic, protective film on sensor lenses. For proper operation, plastic
film must be removed after installation.
Installing freestanding dispensers
1. Position dispenser in desired location and adjust legs to level in both directions.
2. Connect water supply to 3/8" FPT fitting on back of dispenser (Fig. 1).
3. Connect separate drain lines to 3/4" MPT dispenser drain fitting, and 3/4" MPT ice machine drain fitting
on back of dispenser.
4. Run drain lines to wall or floor drain. If ice machine drain fitting is below an intended wall drain, a
condensate pump must be used.
5. If ice machine is a water-cooled unit, connect water-cooled condenser supply line to 3/8" FPT condenser
inlet fitting on back of dispenser.
Note: Do not run condenser supply water through ice machine water filter system.
6. Connect condenser drain line to 3/8" FPT condenser outlet fitting on back of dispenser.
Important: Do not connect condenser drain line to any other drain lines.
7. Plug dispenser into 15A rated NEMA 5-15 circuit.
8. Remove front cover of base section by removing two screws at bottom corners of cover. Allow cover to
drop approximately 3/8" (5 mm) and pull forward.
9. Turn on water supply and check for leaks.
100CR/CT/FB Ice and Water Dispensers
5
Fig. 1 – Rear connections, freestanding models
power cord
NEMA 5-15
access panel
3/4" MPT drain
12.25" (31.2 cm)
4.75" (11.9 cm)
4.5" (11.4 cm)
3.75" (9.3 cm)
2.75" (6.8 cm)
3/8" FPT
water inlet
3/8" FPT condenser outlet location
(water-cooled only)
3/8" FPT condenser outlet location
(water-cooled only)
33.75" (85.8 cm)
31.5" (80 cm)
14" (35.7 cm)
12.38" (31.4 cm)
9.62" (24.4 cm)
3/4" MPT ice machine drain location
10.Remove top front cover by removing two screws at bottom corners of cover. Lift cover slightly and pull
forward.
11.If dispenser is equipped with SensorSAFE remove protective plastic coating from dispense sensor labels.
12.Turn on dispenser power and bin signal rocker switches. Check dispenser and ice machine operation.
13.Sanitize ice machine according to instructions in ice machine manual. Discard ice made during sanitizing
process.
14.Turn off ice machine bin signal switch.
15.Remove dispenser hopper lid; sanitize dispenser according to instructions beginning on page 12.
16.Turn ice machine bin signal switch on and replace front covers, securing with screws.
6
100CR/CT/FB Ice and Water Dispensers
Installing countertop dispensers
Fig. 2
CAUTION!
UNDERSIDE VIEW OF DISPENSER
23.63" (60.0 cm)
Dispensers with top mount ice machines cannot
be mounted on legs. They must be bolted to
counter. Use gloves when lifting ice machine to
protect hands from sheet metal edges.
1. Position dispenser in desired location, mark
dispenser outline on counter and remove
dispenser.
2. Regardless of whether utilities will exit
through back or bottom of dispenser, drill
four (4) 3/8" holes in counter to anchor
dispenser to counter (Fig. 2).
14.00" (35.6 cm)
2.00" (5.1 cm)
9.25"
(23.5 cm)
0.44"
(11 mm)
1.50"
(3.8 cm)
CUTOUT
17.31"
(44.0 cm)
Follett countertop dispensers can have any or all
utilities run directly through counter or out rear of
dispenser. For dispensers with any utilities exiting
through counter, make counter cut-out (Fig. 2).
3. For utilities exiting through bottom only:
(a) Make cut out as shown in
Fig. 2.
Fig. 3 – Bottom exiting utilities (countertop units)
(b) Move drain fitting from back of dispenser
and mount where shown in Fig. 3.
(c) Cut drain tube to length and attach to barbed
connection.
(d) Move inlet water fitting from back of
dispenser and mount where shown in Fig. 3.
(e) Cut water tubing to length and re-insert into
water fitting.
4. If ice transport tube will exit out rear of
dispenser, remove ice transport tube knockout from rear of dispenser. Install supplied
grommet for CR models.
Note: Utility connections can be accessed through
front of dispenser by removing stainless
steel splash panel, or by removing access
panel (Fig. 4) on back of dispenser.
100CR/CT/FB Ice and Water Dispensers
bracket
drain tube
drain
fitting
inlet
fitting
7
Fig. 4 – Rear connections, countertop models
CONDENSER INLET
3/8" NPT FEMALE
WATER COOLED ONLY
8.22" (201 cm)
6.06" (15.5 cm)
CONDENSER OUTLET
3/8" NPT FEMALE
WATER COOLED ONLY
POTABLE WATER INLET
3/8" NPT FEMALE
DRAIN
3/4" NPT MALE
44.97" (114 cm)
41.97" (106 cm)
38.97" (99 cm)
35.91" (91 cm)
ACCESS PANEL
1.34" (35 mm)
8.22" (20.8 cm)
12.25" (31 cm)
0.78" (20 mm)
DRAIN
3/4" NPT MALE
WATER INLET
(INTERNAL)
3/8" NPT FEMALE
5. If power is to be supplied through counter cut-out, complete steps 6-9. If power is to be supplied through
rear of dispenser, proceed to step 10.
6. Temporarily remove rear access panel (Fig. 4) from rear of dispenser.
7. Loosen junction box mounting screws. Lift junction box and power cord up until cord and mounting
screws clear notches on rear panel of dispenser. Remove Phillips head screws from right side of junction
box.
8. Rotate junction box 90 degrees so that screw holes on right side of junction box align with holes on rear
dispenser panel. Resecure junction box to dispenser using Phillips head screws.
9. Place power cord inside dispenser and replace access panel (Fig. 4) to rear of dispenser.
Note: For dispensers to be installed with utilities connected through rear of dispenser, it may be easier to make
preliminary connections before dispenser is set in place.
10.Apply a thick bead, approximately. 1/4" (6 mm) diameter, of NSF listed silicone sealant (Dow-Corning*
RTV-732 or equivalent) 1/4" (6 mm) inside marked outline of dispenser.
11.Carefully position dispenser on counter.
12.Remove four screws securing splash panel to front of dispenser and gently lay splash panel on counter.
(Water line to solenoid valve can be disconnected from water inlet valve by pushing on ring at end of inlet
fitting while pulling on tubing.)
13.Secure dispenser to counter with four 3/8" bolts (supplied by others).
14.Smooth excess sealant around outside of dispenser.
15.Proceed with either RIDE or top-mounted ice machine connection instructions, as appropriate.
* Dow Corning is a registered trademark of Dow Corning Corporation in the United States and other countries
8
100CR/CT/FB Ice and Water Dispensers
Installing RIDE ice machines
CAUTION!
See Ice Machine Installation Manual (form #01062587) for critical installation instructions for RIDE ice machines.
Failure to comply with these instructions will result in poor performance and void warranty.
1. Install RIDE ice machine following instructions in ice machine manual.
2. If dispenser is equipped with SensorSAFE remove protective plastic coating from dispenser lenses.
3. Remove top front cover by removing two screws at bottom corners of cover. Lift cover slightly and pull
forward. Turn on power and bin signal rocker switches. Replace front cover and secure with screws. Test
operation.
4. Sanitize ice machine following instructions in ice machine manual. Discard ice made during sanitizing
process.
5. Sanitize dispenser hopper following instructions on page 12. Installation is complete.
Fig. 5 – Ice transport tube and ice level control stat mounting for freestanding dispensers and countertop
units with RIDE ice machine
ice level control stat
1.00"
(25.4 cm)
engaging pin
ice tube
ice hose mounting bracket
0.187 (5 mm) ice tube hole
100CR/CT/FB Ice and Water Dispensers
9
Installing top mount ice machines
Models 110CT425A/W
CAUTION!
Dispensers with top mount ice machines cannot be mounted on legs. They must be bolted to counter. Use gloves
when lifting ice machine to protect hands from sheet metal edges. See Ice Machine manual.
1. Remove dispenser top front cover by removing two screws at bottom corners of cover, lifting cover slightly
and pulling forward.
2. Remove ice machine compartment top and side panels.
3. Remove ice machine hold-down bracket from front of ice machine compartment.
4. Lift ice machine onto dispenser top and slide ice machine completely into position, compressor end first.
5. Reinstall hold-down bracket on front of ice machine with power cord and bin signal cords in notch. Do not
cut or pinch cords.
6. Insert loose end of ice transport tube through bracket (on ice machine base) into hopper access hole.
Tighten transport tube clamp screw to secure ice transport tube.
7. Connect plastic water supply line to water fill solenoid.
3
1
1.00" (2.54 cm)
10
2 Tighten clamp
screw
100CR/CT/FB Ice and Water Dispensers
VENT
CLEANING
8. Connect molded drain tube to evaporator
drain CUP
pan, purge solenoid and rear drain fitting.
RESERVOIR FILL
SOLENOID
EVAPORATOR
ICE
NOZZLE
WATER SUPPLY
3/8" FPT, 45-90 F (7-32 C)
10-70 PSI (69-483 KPA)
WATER
RESERVOIR
DRAIN PAN
TO DRAIN CUP
9. Connect dispenser bin signal cable to two-pin receptacle on the ice machine electrical box ➊ and
connect the three-pin receptacle to the ice machine electrical box ➋.
2
1
10.On dispensers equipped with water-cooled ice machines, connect condenser water supply and drain
lines to condenser fittings on ice machine.
11.Turn on water supply and check for leaks.
12.Plug dispenser power cord into 15A rated NEMA 5-15 circuit.
13.If dispenser is equipped with SensorSAFE, remove protective plastic coating from dispense sensor
labels.
14.Turn on power and bin signal rocker switches and test operation.
15.Sanitize ice machine following instructions in ice machine manual.
16.Remove dispenser hopper access lid and sanitize dispenser according to instructions on page 12.
17.Replace front cover and secure with screws. Installation is complete.
ice level control thermostat
0.75" (19 mm)
Hand bend cap tube
end to approximately
45° as shown
45°
100CR/CT/FB Ice and Water Dispensers
11
User information
How the dispenser works
Follett’s 110 series automatic-load ice and water dispensers are equipped with Follett’s 425 lb (193 kg)/day ice
machine. In the continuous icemaking process, water freezes to the inside wall of the evaporator. A rotating
stainless steel auger carries the ice to the top of the evaporator where it is compressed and extruded through an
outlet port. The ice is then pushed through a tube to the storage hopper. When the hopper is full, a bin thermostat
opens and shuts the ice machine off. When the dispense mechanism is activated, a dispense motor is turned on,
causing the wheel to turn. This moves ice to the dispense chute where it drops by gravity into the container held
below the chute.
How SensorSAFE infrared dispensing works
Follett’s SensorSAFE infrared dispensing maximizes sanitation and minimizes the possibility of crosscontamination by eliminating physical contact between the cup or container and dispenser. Sensors in the panel
use reflected infrared light to detect the presence of the container and send a signal to a control board which then
activates the appropriate components for ice or water dispensing.
The SensorSAFE infrared dispensing package includes a cleaning switch under the left side of the front cover
which temporarily shuts off dispensing to allow cleaning of the panel and lenses. If the switch is not turned back on
after cleaning, the dispenser automatically resets after two minutes for normal operation.
SensorSAFE infrared dispensing also includes a time limit safety feature which automatically stops ice dispensing
after one minute of continuous dispensing. Dispensing can be resumed by moving the container away from the
dispenser and returning it to the activation zone.
Quiet Night™/Sleep cycle (does not apply to CR units)
The board monitors ice dispensing through a line voltage input to P15. If the ice dispense has not been initiated for
more than 5 seconds during the 20 minute time delay, the SLEEP CYCLE LED comes on. The machine will stay
off for 12 hours unless 5 seconds of dispensing is seen. After 12 hours, the SLEEP CYCLE LED goes out and the
ice making will resume if the bin thermostat is closed. The sleep cycle can be deated using the DIP switches on
the ice machine control board.
Cleaning/descaling and sanitizing
Follett ice machines and dispensers, and their associated cleaning and sanitizing procedures, are designed for
use with potable water sources. The presence, or suspected presence, of infectious agents may call for additional
measures, including the replacement of components and more comprehensive disinfection measures. Follett
recommends that these cleaning and sanitizing procedures be reviewed with the appropriate infectious agent
subject matter experts to assure complete remediation.
Periodic cleaning/descaling and sanitizing of Follett’s ice and water dispenser and ice machine system is required
to ensure peak performance and delivery of clean, sanitary ice. The recommended cleaning procedures that follow
should be performed at least as frequently as recommended and more often if environmental conditions dictate.
Follett recommends sanitizing the pressurized water lines prior to cleaning/descaling and sanitizing the ice
machine/dispenser. Follett offers two kits: order P/N 01089572 when a Follett filter system with a pre-filter bowl
is present, or P/N 01089580 when a Follett filter system is not present. Follow the instructions provided with the
respective kits to sanitize the pressurized water lines immediately before cleaning/descaling and sanitizing the ice
machine/dispenser.
Cleaning of the condenser can usually be performed by facility personnel. Cleaning/descaling and sanitizing of
the ice machine system should be performed by your facility’s trained maintenance staff or a Follett authorized
service agent. Regardless of who performs the cleaning, it is the operator’s responsibility to see that this cleaning
is performed according to the schedule below. Service problems resulting from lack of preventive maintenance will
not be covered under the Follett warranty.
12
100CR/CT/FB Ice and Water Dispensers
Recommended cleaning/descaling and sanitizing intervals*
Symphony Plus
Frequency
Drain Line
weekly
Drain Pan/Drip Pan
weekly
Exterior, Water Station Tube
as needed
Condenser
monthly (air-cooled only)
Dispenser and Components
semi-annually
Ice Machine
semi-annually
Transport Tube
semi-annually
Ice Storage Area/Bin
semi-annually
Pressurized Water Sanitizing
semi-annually
* Ice machine and dispenser must be sanitized prior to start-up.
Weekly
CAUTION!
§§ Do not use solvents, abrasive cleaners, metal scrapers or sharp objects to clean any part of the dispenser.
Dispenser drain pan and drain line
1. Pour 1 gal. (3.8 L) of hot tap water into drain pan to flush drains.
Splash panel front, SensorSAFE infrared dispensing
1. Deactivate dispensing by pressing and releasing clean switch located on left side of unit under top front
cover.
2. Clean lens and splash panel front using a soft cloth and mild, non-abrasive, non-chlorine based cleaner.
3. Reactivate dispensing by pressing and releasing clean switch again.
Monthly
CAUTION!
§§ Do not use solvents, abrasive cleaners, metal scrapers or sharp objects to clean any part of the dispenser.
Condenser (air-cooled ice machine only)
1. Use a vacuum cleaner or stiff brush to carefully clean condenser coils of lint and debris to ensure optimal
performance.
100CR/CT/FB Ice and Water Dispensers
13
Semi-Annually (more often if conditions dictate)
§§ A cleaning/descaling and sanitizing procedure should always include both the ice machine and dispenser.
§§ Icemaking system can be cleaned/descaled in place.
CAUTION!
§§ Wear rubber gloves and safety goggles (or face shield) when handling cleaner or sanitizer mixtures.
§§ Use only Follett approved cleaners.
§§ It is a violation of Federal law to use Cleaning or Sanitizing solution in a manner inconsistent with their labeling.
§§ Do not use solvents, abrasive cleaners, metal scrapers or sharp objects to clean any part of the dispenser.
Cleaning:
Following manufacturer’s instructions, mix cleaning solution of 1 gal. (3.8 L) 100 F (38 C) water
and 7 oz (198 g) (one 7 oz packet) of Follett SafeCLEAN™ ice machine cleaner/descaler
(P/N 00132001).
Sanitizing: Following manufacturer’s instructions, mix a sanitizing solution of 1 gal. (3.8 L) 100 F (38 C) water
and 1.6 oz (48 ml) Nu-Calgon IMS-II or IMS-III Sanitizer (P/N 00979674).
Cleaning & Sanitizing Tool Checklist
§§ (2) 1.5 Gallon (or larger) Plastic Buckets
§§ (2) clean cloths
§§ Sanitary gloves
§§ Safety Glasses
§§ (2) Sani-Sponge™ (P/N 00131524 - single sponge)
§§ (1 ) Packet of SafeCLEAN™ (P/N 00132001 - 24 packets)
§§ 1.6 fl oz of Nu-Calgon IMS-II or IMS-III Sanitizer (P/N 00979674 - 16 fl. oz bottle)
Ice Machine and Dispenser
Cleaning/Descaling Procedure
Note: Check drains and drain cup to ensure they are open and flowing freely.
1. Remove front cover and turn OFF bin signal switch.
2. Dispense all ice from storage hopper and discard.
Note: CI Models only: remove splash panel.
3. Press CLEAN switch. The MAINTENANCE light will turn on and the machine will drain. Wait for the LOW
WATER light to turn on.
4. Remove lid from cleaning cup and fill (about 1 quart) until cleaning solution completely fills the reservoir.
Place lid back on cup. Save remainder of cleaning solution.
5. CLEANER FULL light will turn on and machine will start cleaning cycle then rinse three times; this
process takes approximately 15 minutes.
6. While ice machine is cleaning/descaling, clean dispenser as follows:
a.Turn OFF dispenser power.
b. Remove hopper lid. (Note: for CT models, remove hopper access cover)
c. Remove knurled nuts from front of storage hopper.
d. Remove stud assembly, baffle, wheel, and any remaining ice.
e. Remove dispense chutes from splash panel.
f. Submerse drain grill in cleaning solution and allow to soak to remove any scale buildup.
g. Wipe stud assembly, baffle, wheel, inside of storage area, dispense chutes, drain grill and drain pan with
damp cloth wrung out in cleaning solution. Thoroughly rinse all parts with damp cloth wrung out with clean
water.
Note: To avoid possible damage to motor assembly, only use a damp cloth to clean storage hopper. Do not
allow water to run through motor shaft hole in bottom of hopper.
7. When machine is finished cleaning, the MAINTENANCE light will turn off.
14
100CR/CT/FB Ice and Water Dispensers
Sanitizing Procedure
8. Press CLEAN switch. The MAINTENANCE light and LOW WATER light will turn on.
9. Fill cleaning cup until sanitizing solution completely fills the reservoir. Place lid back on cup. Save
remainder of sanitizing solution.
10.CLEANER FULL light will turn on and machine will start sanitizing cycle then rinse three times; this
process takes approximately 15 minutes.
11.While ice machine is sanitizing, sanitize dispenser as follows:
a. Wipe inside of hopper lid, stud assembly, baffle, wheel, inside of storage area, dispense chutes, drain grill
and drain pan with damp cloth wrung out in sanitizing solution.
Note: To avoid possible damage to motor assembly, only use a damp cloth to clean storage hopper. Do
not allow water to run through motor shaft hole in bottom of hopper.
b. Reinstall dispense chutes, wheel, baffle, stud assembly and knurled nuts. (See manual for correct baffle
position.)
12.When machine is finished rinsing, the MAINTENANCE light will turn off. Loosen phillips-head screw on
nozzle connected to evaporator. Remove nozzle from evaporator side only, leave other side of nozzle
connected to transport tube.
13.Place one Sani-Sponge in remaining sanitizing solution.
14.Insert the sponge soaked in sanitizing solution into nozzle then insert a dry sponge into the nozzle.
15.Replace nozzle onto evaporator and tighten screw. Ensure drain is connected to reservoir and vent tubes
are connected to evaporator drain pan.
16.Turn ON bin signal switch. Wait for ice to push sponges through transport tube.
17.Collect sponges from ice storage bin.
18.Replace hopper lid (access cover for CT models), machine top, turn ON dispenser power and install
front cover.
19.After 10 minutes, dispense all ice and discard.
Dispenser only
Cleaning/descaling procedure
Note: Check drains and drain cup to ensure they are open and flowing freely.
1. Remove and discard all ice from storage hopper.
2. Ensure power is disconnected. Working inside storage area, remove center thumbscrew from dispense
wheel, tilt wheel up toward back to clear baffle and disengage wheel from motor shaft.
3. Remove dispense chutes.
4. Thoroughly wipe lid, dispense wheel, baffle and dispense chutes with cloth soaked in cleaning solution.
5. Wipe all bin surfaces (including the area under dispense wheel) with a damp cloth wrung out in cleaning
solution.
Note: To avoid possible damage to dispense motor assembly, use only a damp cloth to clean the
storage bin. Do not allow water to run through bottom of bin area.
6. Remove grille and wash with cleaning solution. Rinse thoroughly with clean water.
7. Rinse all above items with damp cloth wrung out in clear water.
100CR/CT/FB Ice and Water Dispensers
15
Sanitize dispenser
8. Wipe all above items with damp cloth wrung out in sanitizing solution to sanitize. Do not rinse.
9. Reinstall all parts and replace any panels removed prior to cleaning.
10.Pour 1 gal. (3.8 L) of hot tap water into drain pan to flush drains.
11.If the dispenser is equipped with a Chilled Water Accessory continue to Step 11.1; if not, skip to Step 12.
11.1 Remove four screws securing splash panel.
11.2 Disconnect 3/4" (19 mm) drain line from bottom of chilled water canister.
11.3 Loosen (do not remove) screw securing front bracket of chilled water canister to bottom of dispenser
hopper.
11.4 Rotate canister clockwise to release front bracket, then pull canister forward to disengage rear
bracket.
11.5 Remove chilled water coil from canister and clean with cloth wrung out in cleaning solution.
11.6 Wipe inside of chilled water canister with cloth wrung out in cleaning solution.
11.7 Rinse all above items with damp cloth wrung out in clear water.
11.8 Sanitize all above items with damp cloth wrung out in sanitizing solution. Do not rinse.
11.9 Reinstall chilled water coil into canister (rubber alignment grommet on coil tubing must be located
outside chilled water canister to hold coil securely against canister wall).
11.10 Reinstall chilled water assembly on dispenser and tighten screw securing front bracket.
11.11 Reconnect 3/4" (19 mm) drain line to chilled water canister.
11.12 Reinstall splash panel and top front cover.
12.If so equipped, turn ice machine ON and begin to make ice (ice machine should start immediately with
power and bin signal supplied).
13.After approximately 30 minutes, test dispenser for proper dispensing.
16
100CR/CT/FB Ice and Water Dispensers
100CR/CT/FB Ice and Water Dispensers
17
18
88 BLUE
39 BLACK
38 BLACK
GROUND
SCREW
CT ICE MACHINE
BIN SIGNAL
(CONTACT CLOSURE)
96 BLACK
95 GREEN
94 WHITE
93 BLACK
12
97 WHITE
1 2 3 4
98 BLACK
GROUND-GREEN
75 BLACK
74 GREEN
73 WHITE
72 BLACK
CT ICE
MACHINE
POWER
104 WHITE
115/1/60-BLACK
NEUTRAL-WHITE
109 BLACK
T-STAT
107 BLACK
TIMER
3
2
1
LEVER DISPENSERS
CONTROL BOX
110 PURPLE
BIN
SIGNAL
SWITCH
108 BLACK
4x4
POWER
BOX
104 WHITE
100 BLUE
101 BLACK
96 BLACK
44 RED
S
POWER
SWITCH
RELAY 2
1
3
NC
6
4
NO
9
7
COM
B
A
111 WHITE
114 WHITE
GROUND
SCREW
99 BLACK
102 WHITE
100 BLUE
RELAY 1
1
3
NC
6
4
NO
9
7
COM
B
A
117 BLACK
WATER
SOLENOID
WATER
STATION
SWITCH
118 WHITE
114 WHITE
117 BLACK
91 WHITE
89 PURPLE
102 WHITE
110 PURPLE
DISPENSE 2 2
MOTOR 1 1
39 BLACK
9 9 49 BLACK
38 WHITE
8 8 48 WHITE
37 ORANGE
7 7 47 ORANGE
36 PURPLE
6 6 46 PURPLE
35 BLUE
5 5 45 BLUE
34 RED
4 4 44 RED
33 BLACK
3 3 43 BLACK
32 WHITE
2 2 42 WHITE
31 GREEN
1 1 41GREEN
47 ORANGE
111 WHITE
118 WHITE
M
90 PURPLE
85 ORANGE
5 5 37 ORANGE
84 RED
4 4 77 RED
36 PURPLE
83 PURPLE
3 3 35 BLUE
82 BLUE
2
2 1 76 WHITE
81 WHITE
1
12
1 1
2 2
3 3
LOAD
92 PURPLE
1 2 3 4
WHITE
ORANGE
INPUT
STATION
SWITCH
LEVER DISPENSERS
SPLASH PANEL ICE
FB/CR ICE MACHINE POWER
FB/CR ICE MACHINE BIN SIGNAL
(CONTACT CLOSURE)
S
DISPENSE GATE SOLENOID
Wiring diagram - Lever
74 GREEN
78 WHITE
79 BLACK
87 WHITE
86 WHITE
100CR/CT/FB Ice and Water Dispensers
100CR/CT/FB Ice and Water Dispensers
S
75 BLACK
74 GREEN
73 WHITE
72 BLACK
39 BLACK
38 BLACK
GROUND
SCREW
96 BLACK
95 GREEN
94 WHITE
93 BLACK
NEUTRAL-WHITE
GROUND-GREEN
97 WHITE
12
98 BLACK
1 2 3 4
114 WHITE
104 WHITE
BIN 110 PURPLE
SIGNAL
SWITCH
CT ICE MACHINE
BIN SIGNAL
(CONTACT CLOSURE)
T-STAT
107 BLACK
109 BLACK
CT ICE
MACHINE
POWER
104 WHITE
102 WHITE
100 BLACK
101 BLACK
RELAY 2
1
3
NC
6
4
NO
9
7
COM
B
A
118 WHITE
114 WHITE
116 PURPLE
108 BLACK
POWER
GROUND
SWITCH
SCREW
116 PURPLE
99 BLACK
102 WHITE
108 BLACK
119 PURPLE
CLN
WTR
ICE
TIMER
3
2
1
TO
SPLASH
PANEL
SensorSAFE
DISPENSERS
CONTROL BOX
117 BLACK
115/1/60-BLACK
4x4
POWER
BOX
39 BLACK
9 9 49 BLACK
38 WHITE
48 WHITE
8 8
37 ORANGE
7 7
36 PURPLE
6 6 46 PURPLE
35 BLUE
5 5 45 BLUE
34 RED
4 4 44 RED
33 BLACK
3 3 43 BLACK
32 WHITE
2 2 42 WHITE
31 GREEN
1 1 41 GREEN
SOL WM
RELAY 1
1
3
NC
6
4
NO
9
7
COM
B
A
WTR
GND
117 BLACK
91 WHITE WATER
SOLENOID
37 ORANGE
77 RED
36 PURPLE
35 BLUE
76 WHITE
12
45 BLUE
L1
110 PURPLE
M
83 PURPLE
82 BLUE
81 WHITE
5
4
3
2
1
1 2 3 4
105 WHITE
106 BLACK
112 ORANGE
111 WHITE
LOAD
118 WHITE
DISPENSE 2 2
MOTOR 1 1
5
4
3
2
1
FB/CR ICE
MACHINE
POWER
CLEAN
SWITCH
1 1
2 2
3 3
103 GREEN
INPUT
92 PURPLE
WATER SENSOR
TO
BOX
FB/CR ICE
MACHINE
BIN SIGNAL
(CONTACT CLOSURE)
WHITE
ORANGE
100 BLACK
NEUTRAL
ICE SENSOR
SensorSAFE
DISPENSERS
SPLASH PANEL
S
DISPENSE GATE SOLENOID
Wiring diagram - SensorSAFE
74 GREEN
78 WHITE
79 BLACK
86 WHITE
87 WHITE
19
Dispenser troubleshooting
CAUTION!
§§ Disconnect power to unit before putting hands or arms in storage area or attempting any repair or service to
equipment.
Before calling for service
1. Check that no ice is in the dispenser bin area.
2. Check that congealed ice is not causing a jam.
3. Check that all switches and circuit breakers are on.
4. Check that all drains are clear.
Lever model troubleshooting guide
Problem
Does not dispense ice.
Indicators
1.Power switch off or faulty.
2.Faulty dispense switch.
Does not dispense water.
1.Check switch – turn on or replace if
faulty.
3.Wheelmotor malfunction.
2.Replace switch.
1.Dispense switch contacts
burned shut.
1.Replace water solenoid valve.
2.Debris preventing valve from
closing.
Water runs continuously.
Corrective Action
3.Check motor and capacitor and replace.
2.Replace dispense switch.
3.Check switch - turn on or replace if faulty.
1.Faulty water solenoid valve.
1.Check switch and replace if faulty.
2.Faulty dispense switch.
2 Remove and clean valve.
3.Power switch off or faulty.
Dispense wheel rotates
continuously.
Dispense switch contacts are
burned out.
Replace dispense switch.
Ice machine runs continuously.
Faulty or incorrectly positioned
bin stat.
Check for proper positioning. If stat does
not open when ice is placed on capillary
tube, replace stat.
Ice dispenses by itself.
1.Baffle not adjusted properly.
1. See Adjustment Instructions.
2.Faulty dispense switch.
2.Replace dispense switch.
1.Dispenser is in sleep mode.
1.Verify sleep mode LED is illuminated on
control board.
Not making ice.
2.Dispense 5 seconds worth of ice to reset.
20
100CR/CT/FB Ice and Water Dispensers
SensorSAFE model troubleshooting guide
SensorSAFE Board LED
Status
Problem
Does not
dispense ice
and/or water.
Dispenses ice
and/or water
continuously.
Action
PWR
CLN
ICE/
WTR
Check
LEDs on the
SensorSAFE
control board.
OFF
OFF
OFF
Check circuit breakers and power switch.
Restore power or replace defective switch.
ON
ON
OFF
Press clean switch on lower left side of electrical
enclosure to return board to normal operation.
Place cup
under drop
zone (in front
of lens).
ON
OFF
OFF
Troubleshoot appropriate lens/sensor
and replace if required (see lens/sensor
troubleshooting).
ON
OFF
ON
Verify power on appropriate output terminal
(WTR or WM) on control board and replace
board if required. If board tests okay,
troubleshoot appropriate dispenser component.
ON
OFF
ON
Troubleshoot appropriate lens/sensor
and replace if required (see lens/sensor
troubleshooting).
ON
OFF
OFF
If there is power on any output terminal 9 (WTR
or WM) on control board, replace board.
Check LEDs
on control
board.
Corrective Action
Board guide
LEDs, when illuminated, indicate the following: PWR (board power), CLN (cleaning, no dispensing cycle), ICE (ice
dispensing activated), WTR (water dispensing activated).
Terminals: LI (incoming power, hot), L2 (neutral terminals), WTR (power terminal for water solenoid), WM (power
terminal for wheelmotor), CLN (terminals for clean cycle switch).
Note: SOL terminal not used in 12 series dispensers.
Lens/sensor troubleshooting
1. Turn dispenser power switch off and remove splash panel.
2. Disconnect wires from WTR and WM terminals on board.
3. Gently remove sensor/mounting block from splash panel.
4. Inspect lens and sensor, clean if necessary.
5. Restore dispenser power and test sensor by passing hand in front of sensor.
6. If LED on board turns on, sensor is operational. Re-assemble dispenser.
7. If LED does not come on switch sensor leads on board and retest.
8. If opposite LED comes on – replace defective board.
9. If opposite LED does not come on – replace defective sensor.
100CR/CT/FB Ice and Water Dispensers
21
Disassembly and replacement instructions
Dispense chute removal
1. Remove dispenser front cover.
2. Slide plastic dispense chute up and out to
remove.
Dispense wheel and drive bar removal
1. Remove all ice from storage area of
dispenser.
2. Remove center thumbnut from dispense
wheel.
3. Remove thumbnuts holding baffle inside bin
and remove baffle.
4. Tilt rear of wheel up and lift off motor drive
shaft.
5. After reinstalling wheel, secure baffle
loosely with thumbnuts, but do not tighten.
6. Place a 1/8" (3.2 mm) spacer against wheel
and allow baffle to drop until it touches
spacer.
7. Tighten thumbnuts and remove spacer.
Fig. 6
dispenser
front
baffle
3.2mm (1/8")
spacer
side view wheel section
Drive bar removal
1. Remove dispense wheel from dispenser
(see above).
2. Pull drive bar out of its channel in bottom of
wheel.
Wheelmotor removal
1. Shut water off. Remove front cover.
2. Remove dispense wheel and dispense
chute covers (see above).
3. Remove splash panel. Water line to
solenoid valve can be disconnected from
water inlet valve by pulling on ring at end of
inlet fitting.
4. Disconnect wiring to panel and set panel
aside.
5. Disconnect wires on motor.
6. Remove four bolts (7/16" socket) holding
motor assembly to bottom of dispenser.
7. Remove motor assembly.
22
100CR/CT/FB Ice and Water Dispensers
Ice transport tube replacement – Top mount units
Models 110CT425A/W
CAUTION!
§§ Use only tubing supplied by Follett Corporation.
3
1
1.00" (2.54 cm)
2 Tighten clamp
screw
Ice transport tube replacement – Freestanding and RIDE models
Models 110FB425A/W, 110CR425A/W
CAUTION!
§§ Correct installation of ice transport tube is critical to RIDE ice machine performance. Replacement ice
transport tubes for RIDE ice machines must be insulated and run continuously from ice machine to
dispenser with no dips or bends with a radius of less than 6" (15.3 cm).
1. Remove top and rear access panel from dispenser (lower front panel in freestanding unit).
2. Disconnect existing ice tube from engaging pin on transport tube bracket in ice storage bin and pull down
through dispenser chase.
3. Disconnect opposite end of tube from ice machine.
4. Run end of new ice transport tube with 3/16" (5 mm) hole through ice transport tube knockout in back of
dispenser or through counter into bottom of dispenser, being careful to avoid any bends with less than 6"
(15.3 cm) radius.
5. Insert tube in internal chase in rear inside corner of dispenser (left side as you face dispenser) and push
up into storage area.
6. Push the 3/16" (5 mm) hole near end of tube into pin on ice tube bracket (Fig. 8).
Fig. 7
3/16" (5 mm)
dia. hole
ice level control stat
engaging pin
1.00"
(2.54 cm)
Section A – A
ice tube
1.00"
(2.54 cm)
A
A
ice hose mounting bracket
3/16" (5 mm) ice tube hole
100CR/CT/FB Ice and Water Dispensers
23
Steps 7-8 for units with RIDE ice machines only
Fig. 8
All units
7. Slip supplied hose clamp onto tube.
8. Heat end of transport tube in cup of 160 F
(71 C) hot water to soften and spread with
pliers (Fig. 8) before making connection to
exit port of evaporator. Do not twist hose
when securing to evaporator.
Note: Only use tubing supplied by Follett
Corporation.
Hot Water
160 F (71 C)
9. Fasten tube on port with hose clamp,
ensure that clamp is positioned on
evaporator side of nozzle flange.
10.Tighten clamp.
All units
11.Slip supplied hose clamp onto tube and push tube onto exit port of evaporator. Do not twist hose when
securing to evaporator.
Note: Only use tubing supplied by Follett Corporation.
12.Fasten tube on port with hose clamp, ensure that clamp is positioned on evaporator side of nozzle flange.
13.Tighten clamp.
Thermostat replacement
ice mounting hose bracket
well nut
knurled screw
rubber grommet
ice level control stat
ice level
control stat
bin thermostat
control box assembly
hopper assembly
control box assembly
24
100CR/CT/FB Ice and Water Dispensers
Replacement parts
Dispenser exterior
7
2
7
2
6
4
5
1
3
8
Reference
1
2
3
4
Not shown
5
Not shown
6
7
Not shown
8
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
9
9
Description
Cover, top front, CT, ice and water
Cover, top front, CR/FB, ice and water
Cover, lower section, FB
Cover, dispense chute
Knurled screws, front cover
Drain pan
Grille, drain pan
Lid, ice machine, 110, countertop (CT)
Lid, secured, 110, countertop (CR) units with RIDE ice machines & freestanding (FB)
units
Leg kit, for freestanding units – set of 4
Single leg, for freestanding units
Drain tube assembly
Cover, top front, CT, ice only
Cover, top front, CR/FB, ice only
Tee, water inlet, 1/4"
Valve, water shut-off, 1/4"
Drain fitting, plastic, ice machine (includes screws)
Cord, power, dispenser, CR/CT/FB
Cord & plug, bin signal, RIDE ice machine, 20'
Cord & plug, bin signal, top mount and freestanding
Clean switch, SensorSAFE
Cord & plug, ice machine power, FB and CT (dispenser box to ice machine box)
Caster
Screw, knurled, 1/4-20 x 1"
100CR/CT/FB Ice and Water Dispensers
Part #
01072818
01072792
502704
502681
01085703
502705
502706
502709
01072784
502088
502298
502711
01072826
01072800
502923
01035526
00109728
01027648
01074202
01074210
502359
01074848
502805
01059855
25
Wheelmotor and drive system
3
8
7
5
4
6
7
2
7
1
1
Reference
Description
Part #
1
Wheelmotor, 120 V, 60 Hz
501861
2
Washer, thrust
501026
Not shown
Fan blade, wheelmotor
501607
3
Drive shaft (includes key and stud)
501619
4
Chain, pitch 54, link
502691
5
Sprocket, drive shaft, 35T
502692
6
Sprocket, wheelmotor, 10T
501019
7
Bearing, drive shaft
501024
Not shown
Connecting link, chain
500799
8
Key, drive shaft
500637
Parts 1-8 above
Dispenser drive assembly
502020
26
100CR/CT/FB Ice and Water Dispensers
Dispense chute and splash panel (models with lever dispensing)
15
3
14
1
4
11
16
8
12
9
6
10
13
7
5
2
Reference
Description
Part #
1
Tube, water station
502356
2
Cover, dispense chute
502681
3
Switch, dispense, ice, lever actuated (includes 501841)
501829
4
Switch, dispense, water, lever actuated (includes 501841)
502359
5
Lever, dispense
00976845
6
Chute, ice (with Agion antimicrobial product protection )
01042787
7
Chute, water (with Agion)
01042795
8
Solenoid assembly, water, 120V, 60Hz (includes solenoid valve, tube, bracket,
inlet and outlet fittings)
01049121
9
Bracket, lever and water solenoid
01039635
10
Fitting, inlet, 1/4" tube x 1/8 MNPT straight
00991232
11
Fitting, outlet, 1/8" MPT x 3/8" comp
502246
12
Solenoid valve, water, 120 V, 60Hz
502243
13
Boot, dispense switch button
501841
14
Bracket, lever
00958793
15
Splash panel, lever dispense
01039742
16
Fastener, 10-32 x 3/8" stainless steel
00982421
Not shown
Tubing, water station, thermoplastic, 1/4" OD (sold by the foot)
502079
Not shown
Splash panel, lever dispense complete assembly
01049055
Not shown
Splash panel, lever dispense, ice only, complete assembly
01049063
®
1
Disclaimer: Antimicrobial protection is limited to the treated components and does not treat water or ice.
Agion is a registered trademark of Sciessent LLC.
1
100CR/CT/FB Ice and Water Dispensers
27
Dispense chute and splash panel (models with SensorSAFE infrared dispensing)
5
8
10
7
2
11
6
9
13
12
1
3
4
Reference
Description
Part #
1
Cover, dispense chute
2
Chute, ice (with Agion antimicrobial product protection )
01042787
3
Chute, water (with Agion)
01042795
®
502681
1
4
Lens, sensor
502690
5
Splash panel (includes 2 of 502690)
01049162
Not shown
Splash panel, SensorSAFE, ice only (includes 2 of 502690)
01049170
6
Solenoid assembly, water, 120V, 60Hz (includes solenoid valve, tube, bracket, inlet
and outlet fittings) 120V 60Hz
01049121
7
Bracket, lever and water solenoid
01039635
8
Tube, water station
502356
9
Fitting, inlet, 1/4" tube x 1/8 MNPT straight
00991232
10
Fitting, outlet, 1/8" MPT x 3/8" comp
502246
11
Solenoid valve, water, 120V, 60Hz
502243
12
Sensor (includes lens and ty-rap)
00122978
13
Fastener, 10-32 x 3/8" stainless steel
00982421
Not shown
Splash panel, SensorSAFE, complete assembly
01049030
Not shown
Splash panel, SensorSAFE, ice only, complete assembly
01049048
Disclaimer: Antimicrobial protection is limited to the treated components and does not treat water or ice.
Agion is a registered trademark of Sciessent LLC.
1
28
100CR/CT/FB Ice and Water Dispensers
Electrical components
1
1
4
4
4
4
5
5
2
2
2
2
3
Reference
Description
Part #
1
Thermostat, bin level
500514
2
Switch, dispenser power
502209
2
Switch, ice machine bin signal
502209
3
Control board, SensorSAFE
502242
Not shown
Clean switch, SensorSAFE
502359
Not shown
Boot, clean switch
501841
4
5
Relay, bin signal contact closure and level fill
501369
Timer, level fill
501601
100CR/CT/FB Ice and Water Dispensers
29
Hopper components
16
18
12
15
5
3
9
14
17
2
13
7
8
11
5
3
4
2
4
7
10
9
2
Reference
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Not shown
30
Description
Baffle, ice
Wheel, dispense (includes drive bar, rotating agitator, threaded bar & rod)
Agitator, rotating
Bracket, ice tube
Screw
Rod, threaded (includes knurled nut)
Drive bar assembly (includes threaded rod and nut)
Ice deflector/cap tube bracket (units with top mounted ice machine)
Bracket, ice tube entry (units with top mounted ice machine)
Ice transport tube assembly (units with top mounted ice machines)
Side panel, RH
Side panel, LH
Bracket, ice machine hold-down
Cover, hopper access
Cover, hopper, CT
Lid, Ice machine, CT
Gasket, ice entry
Lid, secured, CR/FB
Drain pan, hopper
Part #
501802
501493
501494
502712
501100
501612
501617
501616
01067644
01003532
502723
502722
01074871
502717
01074889
502709
502824
01072784
00115196
100CR/CT/FB Ice and Water Dispensers
Ice transport tubing
Reference
Description
Part #
Not shown
Ice transport tube (RIDE units) - 10 ft
502522
Not shown
Ice transport tube (RIDE units) - 20 ft
502523
Not shown
Ice transport tube insulation (RIDE units only) - sold by the foot
501176
Not shown
Ice transport tube assembly (50 FB units)
502328
Not shown
Ice transport tube assembly (25 FB units)
502329
Not shown
Ice transport tube assembly (top mount units)
01003532
Chilled water components
2
1
1
3
Reference
Description
Part #
Not shown
Coil, chilled water (includes two 502599)
01074111
1
Fitting, water coil
502599
2
Brackets, chilled water canister, pair (includes screws)
502600
3
Elbow, drain
502605
Not shown
Assembly, chilled water
01074137
Not shown
Tubing
01055011
100CR/CT/FB Ice and Water Dispensers
31
Dispenser plumbing connections
TOP VIEW
BOTTOM VIEW
Reference
Description
Part #
Not shown
Valve, water shut-off
01035526
1
Drain tube assembly
01074285
2
Fitting, water inlet
01065275
3
Cup, cleaning
01065226
4
Drain pan
502705
5
Fitting, drain
00109728
Not shown
Tee, water inlet, 1/4"
502923
Not shown
Grille, drain pan
502706
32
100CR/CT/FB Ice and Water Dispensers
Solenoid dispense assembly
2
1
4
3
5
6
8
7
Reference #
Description
Part #
1
Solenoid, dispense
501830
2
Cotter pin
502040
3
Linkage, solenoid (includes 502054 grommet)
502039
4
Block, dispense gate
502042
5
Grommet
502054
6
Splash pan, gate assembly
502045
7
Shoulder screw and washer
502038
8
Spring, gate assembly
501824
—
Gate assembly, 115V (includes reference numbers 1 through 8 above)
502043
100CR/CT/FB Ice and Water Dispensers
33
Water treatment accessories for Symphony Plus ice and water dispensers
Reference #
Description
Part #
Standard capacity filter system
Not shown
Follett QC4-FL4S water filter system (includes FL4S primary cartridge and head,
coarse pre-filter and head, pressure gauge, flushing valve; assembled and installed
on mounting bracket), one per ice machine
00130229
Not shown
Follett FL4S primary replacement cartridge
00130245
Not shown
Water filter cartridge – primary, carton of 6
00954297
Not shown
Everpure coarse pre-filter cartridge
00130211
Not shown
Water pre-filter cartridge – pre-filter, carton of 12
00954305
High capacity filter system
Not shown
High capacity water filter system (one per ice machine)
00978957
Not shown
High capacity water filter cartridge – primary, single
00978965
Not shown
High capacity water filter cartridge – primary, carton of 6
00978973
Not shown
Water pre-filter cartridge – pre-filter, single
00130211
Not shown
Water pre-filter cartridge – pre-filter, carton of 12
00954305
Carbonless high capacity filter system
Not shown
Carbonless high capacity water filter system (one per ice machine) – Horizon™ and
MaestroPlus series ice machines
01050442
Not shown
Carbonless high capacity water filter cartridge – primary, single
01050426
Not shown
Carbonless high capacity water filter cartridge – primary, carton of 6
01050434
Not shown
Water pre-filter cartridge – pre-filter, single
00130211
Not shown
Water pre-filter cartridge – pre-filter, carton of 12
00954305
Other filtration
Not shown
Claris hardness removal filtration system
00986059
Not shown
Replacement filter for Claris system
00985127
Not shown
Reverse osmosis system, 200 gallons per day
00986034
Not shown
Replacement reverse osmosis cartridge
00985085
Not shown
Replacement reverse osmosis pre-filter
00985077
Not shown
Cleaning plug for reverse osmosis system
00985119
Not shown
Cleaning cartridge for reverse osmosis system
00985101
Water pressure
Not shown
Water pressure regulator (25 psi)
501781
Cleaning/Sanitizing
Not shown
SafeCLEAN ice machine cleaner, carton of 24 x 7 oz packets
00132001
Not shown
Sponge, sanitary, each
00131524
IMS-II or IMS-III sanitizing concentrate
Not shown
34
16 oz. bottle
00979674
Case of 12 x 16 oz. bottles
01038652
Sponge, sanitary, pack of 24
01075431
100CR/CT/FB Ice and Water Dispensers
100CR/CT/FB Ice and Water Dispensers
35
SafeCLEAN, SensorSAFE, Maestro Plus, Symphony Plus, Quiet Night and Sani-Sponge are trademarks of Follett Corporation.
Follett and RIDE are registered trademarks of Follett Corporation, registered in US.
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
01033729R03
© Follett Corporation 4/16
Download PDF
Similar pages