SDV8000 Professional Steam, Detergent &

SDV8000
Professional Steam, Detergent
& Vacuum cleaning machine
User Instructions
Warning Do not operate this appliance before reading and understanding
these instructions. Always keep the instructions attached to the appliance or
readily available at the appliance storage site.
SDV8000
Components
1. Detergent Connection Point
2. Cold Water Tank
3. Steam Control
4. Collection Tank
5. Filter Panel
6. Vacuum Hose Socket
7. Steam Hose Socket
Diagram A
8. Castor With Brake
9. Wire Basket
10. Serial Number
Diagram B
11.
12.
11. On/Off Switch
13.
14.
12. Mode Switch
13. Heater On LED
14. Steam Ready LED
15.
15. Cold Water Refill LED
16. Temperature Display LED
17. Pressure Gauge
17.
16.
Attachments
1.
3.
5.
7.
9.
11.
13.
15.
SDV8000
4 Meter Steam, Detergent & Vacuum Hose
Floor Nozzle 400mm
Carpet Insert for Floor Nozzle
Clear Upholstery Tool
Nylon Details Brush x 5
Short Steam Lance
Suction Nozzle 150mm
Clip On Brush 150mm
2.
4.
6.
8.
10.
12.
14.
16.
Glass Washer
Squeegee Insert for Floor Nozzle
Brush Insert for Floor Nozzle
Extension Tubes x 2
Brass Details Brush x 5
Long Steam Lance
Clip on Squeegee 150mm
Accessory Service Kit
Diagram C
1.
7.
12.
15RM00050
15RM00031
15RM00013
13.
2.
8.
15RM00003
15RM00008
15RM00040
14.
9.
3.
15RM00042
15RM00019
15RM00027
15..
10.
4.
15RM00041
15RM00029
15RM00020
5.
15RM00030
11.
6.
15RM00028
16.
15RM00051
Also available is Stainless Steel detail brushes (Packs of 10) : 15RM00018
SUBA15
SDV8000
Accessories
Diagram D
•
Wire Basket
•
Tubular Handle
13RM00008
15RM00016
•
Plastic Wing Nuts x 4
•
Detergent Bottle
12RM00067
SUBA07
•
Back Wheel Assembly
SUBA16
•
Castor with Brake x2
12RM00115
SDV8000
Guidance
Congratulations
………………………………………………...
We would like to take this opportunity to thank you for your purchase of the SageTM Systems
combined steam, detergent and vacuum cleaner.
The SDV8000 is manufactured in the UK to the highest quality Standards
This instruction manual contains all of the necessary information to operate and maintain
this machine. Please read this instruction manual carefully before you start using or
carrying out any maintenance on the machine.
If you use this machine correctly as stated in this instruction manual this machine will fulfil
all your steam cleaning needs.
•
This machine is intended for use in a commercial cleaning environment. If you do
not follow the instructions contained in this manual, situations may arise which may
be dangerous or harmful to the machine or the person operating the machine. Read
this manual carefully so that you know when such situations can arise.
•
Ensure that all operators of this machine are fully trained on how it works.
•
Report any problems or damage to the machine immediately to the supplier or a
SageTM Systems approved supplier for this product. Do not operate the machine until
the problem or damage has been resolved.
Getting the Best Results
………………………………………………...
•
•
Operate the machine in accordance with
the instruction manual
Maintain the machine in accordance
with instruction manual
•
•
Use only parts supplied by SageTM Systems approved
distributors
Use only detergents and cleaning products in the
solution tank which have been approved by SageTM
Systems
Keep this manual in a safe place for future reference and ordering of spare parts
SDV8000
Installation
•
Lift the machine out of the box.
•
Carefully place the machine on its side in
order to assemble the wheels securely.
!! A flat surface is required which will
not scratch or damage the surfaces of the
machine.
•
Diagram D – Back wheel assembly. Using a 10 mm spanner remove the bolts from
the machine and place the assembly into place towards the back of the machine.
Tighten the bolts securely ensuring no movement on the brackets.
Diagram D – Casters with Brake x 2. Remove bolts from the machine and position
into place towards front of the machine. Tighten securely ensuring no movement on
the brackets.
•
•
Once all the wheels are fully assembled, resume the machine to its upright position.
•
Place Tubular Handle (Diagram D) in position on the back of the machine and secure
using the 4 x Plastic Wing Nuts (Diagram D).
!! Do not screw them all the way in at this point.
•
Place Wire Basket (Diagram D) over the Wing Nuts and tighten up to secure.
•
Check all accessories are present in the box as shown in Diagram C & D.
Warnings
………………………………………………...
This machine has been designed with your safety in mind, however it is important that you
observe the following points for safe operation during the operating procedure
•
•
•
•
•
•
This is an electrical product – Do not use in wet weather or allow the machine to get wet.
Do not discharge steam towards people, danger of scolding. Or towards equipment containing
electrical components
Never allow children to play with this appliance.
Do not use the machine for other purposes that it was built for.
Please remember that the steam cleaner operates at temperatures in excess of 170°C. Never
use it on objects, which cannot resist the temperature (delicate materials, fabrics, plastics,
wood etc). Where any doubt exists check carefully on a part of the material where minor
marks will not matter.
Do not operate the machine or carry out any maintenance out on it
Unless you are trained and authorised to do so
Unless you have read and thoroughly understand this instruction manual.
Operating Procedure
………………………………………………...
SDV8000
1. Switch mode switch (Number 12 Diagram B) to position 11.
• This will switch on the boiler elements and will enable you to use the handle
controls on the hose once connected.
2. Fill the cold water tank (Number 2 Diagram A) with clean cold water only.
!! Anything other than clean cold water used in the
water tank will void the manufacturers warranty.
3. Connect the Detergent Bottle (Diagram B) to the detergent connection point (Number
1 Diagram A) on the machine.
4. Fill the detergent bottle (Diagram B) with SageTM Systems approved detergent.
!! Unapproved detergent may be harmful or dangerous to the machine or the
operator using the machine. This may cause irrepairable damage to seals and will
void the manufacturers warranty.
5. Connect the Vacuum Hose to the front of the machine (Number 6 Diagram A) ensuring
it locks into position. To release the vacuum hose from the socket slide the red button
upwards at the same time as pulling the hose out.
!! If the Hose becomes damaged the complete hose must be replaced. Do not
attempt this task yourself, contact a SageTM Systems approved supplier for
replacement.
6. Connect the Steam Hose to the front of the machine (Number 7 Diagram A) ensuring it
is pushed in all the way and the pin on the flap locks into the hole on the hose.
!! Grease “O” rings on steam pin before connecting.
!! To release the steam hose, lift the flap and pull.
7. Plug the power cable into a 240 Volt supply.
!! Inspect the electric cable before every use. If the cable becomes damaged at
anytime the complete cable must be replaced by a SageTM Systems approved
distributor.
!! Never touch the power cable or plug with wet hands
!!
Always unplug the machine when
i. The machine is not in use
ii. Cleaning the machine
iii. Any maintenance work is being carried out
8. Switch the On/Off switch (Number 11 Diagram B) to the ON position. The Heater On
light LED (Number 13 Diagram B) will illuminate.
9. Allow approximately 10 minutes for the boiler to heat the water
10. When the Steam Ready LED (Number 14 Diagram B) illuminates the machine is ready
to be used.
Operating Procedure cont….
………………………………………………...
SDV8000
11. The handle controls are now active.
• The red trigger on the hose handle will release steam when pressed.
• The red button on the side of the handle will lock the steam trigger in the off
position.
• Pressing the left hand switch on top of the handle will activate the vacuum.
• Pressing the right hand momentary switch located on the top of the handle
will activate the detergent pump. Hold the switch as long as you need to
dispense the detergent. Releasing the switch will stop the detergent supply.
12. The steam output can be adjusted by the steam control knob (Number 3 Diagram A)
13. Choose and fit the required accessory (Diagram C) to the hose handle. Lock the
accessory in place by turning the accessory locking clip.
!! When changing accessories during use please note these will be hot.
During Use
………………………………………………...
Cold Water Tank Empty(Number 2 Diagram A)
1. Refill the cold water tank when the refill cold water LED (Number 15 Diagram B) is
illuminated. A buzzer will sound and the steam will no longer come out of the nozzle
when the steam switch on the handle is pressed.
2. Always empty the collection tank each time the cold-water tank is refilled.
3. The pumps will not work when the cold-water tank is empty.
4. Once the cold water refill LED is illuminated the boiler heater will remain on for 30
minutes. If the cold-water tank is not refilled within 30 minutes and the machine is left
powered on the boiler heater will switch off.
Detergent Bottle Empty (Diagram D)
1. If the detergent does not come out of the nozzle when the detergent switch on the handle
is pressed, refill the detergent bottle (Diagram D)
Collection Tank Full (Number 4 Diagram A)
1. Always empty the collection tank each time the cold-water tank is refilled
2. The pitch of the motor noise changes and there is no suction at the nozzle
3. Switch off the machine, empty the collection tank and rinse clean
SDV8000
Maintenance
Warning: Disconnect the machine from the mains before
cleaning or carrying out any maintenance work.
Daily Maintenance
………………………………………………...
To be carried out every day or every 8 hours of operation.
1. Grease “O” rings on the steam pin in the steam hose.
2. Wash the hose by sucking one or two litres of water from a basin into the collection
tank.
3. Empty the collection tank, rinse and wipe down.
4. Remove the foam filter, wash in water and re fit.
• Take care not to damage the filter mesh. If it becomes torn do not use
the machine and replace damaged parts immediately.
5. Rinse detergent bottle with clean water.
6. Wipe down the body of the machine with a clean damp cloth
7. Always wash the accessories in hot soapy water
DO NOT IMMERSE THE MACHINE OR HOSE IN WATER
8. Wrap the power cable around the handle before storage.
Weekly Maintenance
………………………………………………...
To be carried out every week or every 50 hours of operation.
As for daily maintenance plus the following:
1. Inspect the power cable for any signs of damage. If damaged do not repair,
contact the supplier of this product. Do not use until repaired.
2. Inspect the hose assembly for any signs of damage. If damaged do not repair,
contact the supplier of this product. Do not use until repaired.
3. Inspect castors to ensure all securing bolts are fully tightened.
Safety Precautions
………………………………………………...
This machine is to be used by trained operatives only
DO
•
•
•
•
Check the cable and plug are safe and intact
before plugging the machine in.
Place cleaning in progress signs where
necessary
Point the steam nozzle away from your body
during use
Empty and clean machine after each use
DON’T
• Use the machine near people, children or
animals
• Point steam at electrical apparatus
• Use the machine to clean the machine
down
• Do not use on Velvet, satin or leather
• Leave the machine unattended
Service & Guarantee
SDV8000
Service
………………………………………………...
If you require a service or advice on using or maintaining your machine
please contact your SageTM Systems approved distributor. If in doubt,
please contact SageTM Systems direct on +44 (0) 1793 603487.
Guarantee
………………………………………………...
SageTM Systems guarantees that if within 12 months from the date of purchase this
appliance, or any parts thereof, is proved to be defective by reason of faulty workmanship
or materials, we will at our option repair or replace the same free of charge for labour and
materials, provided that:
• The appliance has been installed and used in accordance with our operating and
servicing instructions.
• If the appliance has been serviced, maintained, repaired, modified taken apart or
tampered with by any person not authorised by us, then we will not be liable under
this guarantee for any fault arising from their defective workmanship.
• We shall not be liable under this guarantee for any fault in the appliance arising
from the use of spare parts not supplied and recommended by us.
• Excluded from this guarantee are parts that need replacement due to normal wear
and tear such as hoses, nozzles and accessories.
SDV8000
Technical
Technical Information
………………………………………………...
Boiler
Wattage:
Type:
Capacity:
Continuous Fill
Steam Pressure
Steam at source:
3000W – (2000+1000)
Stainless Steel
3.3 Litres
Yes
8 Bar
165°C >
Vacuum
Type
Motor
Integral
850 Watt
Electrical
Voltage
Low Voltage Controls
Cord length
230V ~ single phase
5V
10m
Capacities
Boiler
Cold Water Tank
Collection Tank
Detergent Tank
Weight
3.3 Litres
5 Litres (easy fill)
12 Litres
2.5 Litres (easy fill)
35kg
Trouble Shooting
Symptom
No power
Possible cause
Not connected / Faulty socket
On / Off switch not on
No steam
Fuse blown
Unknown
Steam Control turned down fully
clockwise
Steamer not ready
Clean water tank is low (beeping
sound& "refill" light is lit)
No steam, Just water
Unknown
Steamer not ready
Boiler at pressure and not
heating(temperature less than
110ºC)
Steam Leaking from
front socket
Unknown
“O” Rings split
“O” rings worn
Vacuum power low
Vacuum operation has been
selected on the machine
High pitch motor noise
No detergent
Unknown
Solution tank empty
Unknown
SDV8000
Action
Check connection to wall socket and
socket switch. Try in another wall
socket
Press On / Off switch which will
illuminate when on
Replace fuse with approved 13A fuse
Call for service
Turn the control to half way
Wait for the “Ready to steam” light to
illuminate
Pour water into the clean water tank
until the beeper stops. The steam
handle will work again.
Call for service
Wait for the "Ready to steam " light
to illuminate
Hold the steam switch on for
approximately one minute, ever if just
water is coming out. This will result
in the heater coming back on
Call for service
Change and re grease “O” Rings. To
avoid this happening ensure “o” rings
are grease before every use.
Change and re grease “O” Rings. To
avoid this happening ensure “o” rings
are grease before every use.
Operate any of the handle controls,
which will reset the motor power to
full. Continue vacuuming
Switch the machine off and empty the
collection tank. Refill the collection
tank with clean water to the mark and
recommence work.
Call for service
Pour cleaning solution diluted in
accordance with the manufacturers
instructions into the solution tank.
Call for service
Download PDF
Similar pages