5713229861/05.16
De’Longhi Appliances via Seitz, 47 31100 Treviso Italy www.delonghi.com
ECAM35X.35
BEAN TO CUP ESPRESSO
AND CAPPUCCINO MACHINE
Instruction for Use
Instruction videos available at:
http://ecam35035.delonghi.com
EN
page 6
B1
B
B3
B2
B4
B6
B5
B7
B8
B9
B10
B11
B12
B13
C
C1
C3
C2
2
C4
A2
A
A1
A5
A24
A3
A23
B
A4
A6
A22
A8
A20
A21
A19
A9
A7
A10
A11
A12
A16
A13
A14
A17
A15
A18
3
3A
1
2
3B
4
5
6
7
8
OK
HOT MILK
NO
9
10
11
13
14
15
4
12
16
17
19
18
21
PU
SH
PU
SH
22A
23
22B
A
20
24
B
28
B
1,8l
25
A
26
27
30
31
0,5 L
29
5
32
CONTENTS
1. FUNDAMENTAL SAFETY WARNINGS..............7
2. SAFETY WARNINGS ....................................8
13.4 Cleaning the drip tray and condensate tray..16
13.5 Cleaning the inside of the coffee machine....16
13.6 Cleaning the water tank...............................16
13.7 Cleaning the coffee spouts...........................17
13.8 Cleaning the pre-ground coffee funnel........17
13.9 Cleaning the infuser.....................................17
2.1 Symbols used in these instructions................8
2.2 Designated use...............................................8
2.3 Instruction for Use..........................................8
14.DESCALING............................................... 17
15. SETTING WATER HARDNESS....................... 18
3.INTRODUCTION...........................................8
3.1 Letters in brackets..........................................8
3.2 Troubleshooting and repairs...........................8
15.1 Measuring water hardness...........................18
15.2 Setting water hardness................................18
4.DESCRIPTION.............................................9
16. WATER SOFTENER FILTER.......................... 18
4.1 Description of the appliance ..........................9
4.2 Description of the accessories.........................9
16.1 Installing the filter.......................................18
16.2 Replacing the filter.......................................19
16.3 Removing the filter......................................19
5. BEFORE USE...............................................9
5.1
5.2
5.3
5.4
Checking the appliance..................................9
Installing the appliance..................................9
Connecting the appliance...............................9
Setting up the appliance..............................10
17. TECHNICAL DATA....................................... 19
19. DISPLAYED MESSAGES............................... 20
18. DISPOSING OF THE APPLIANCE.................. 20
20.TROUBLESHOOTING.................................. 22
21. ELECTRICAL REQUIREMENTS..................... 23
6. TURNING THE APPLIANCE ON.................... 10
7. TURNING THE APPLIANCE OFF................... 10
8. MENU SETTINGS....................................... 10
8.1Rinsing.........................................................11
8.2Language.....................................................11
8.3Maintenance................................................11
8.4 Program beverages......................................11
8.5 Program My beverages................................11
8.6General........................................................11
8.7Statistics.......................................................12
9. MAKING COFFEE........................................ 12
9.1 Adjusting the coffee mill..............................12
9.2 Tips for a hotter coffee.................................13
9.3 Making automatic recipes using coffee beans..
13
9.4 Temporarily varying the coffee aroma..........13
9.5 Making coffee using pre-ground coffee........14
10. MAKING CAPPUCCINO AND HOT MILK (NOT
FROTHED)................................................ 14
10.1 Making hot milk (not frothed).....................15
10.2 Cleaning the cappuccino maker after use.....15
11. PROGRAMMING AND SELECTING................ 15
12. DELIVERING HOT WATER........................... 15
13.CLEANING................................................ 16
13.1 Cleaning the machine..................................16
13.2 Cleaning the machine's internal circuit........16
13.3 Cleaning the coffee grounds container.........16
6
1. FUNDAMENTAL SAFETY WARNINGS
•
•
•
•
•
•
The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
Never clean by immersing the appliance in water.
This is an household appliance only. It is not intended to be used in: staff kitchen
areas in shops, offices and other working environments; farm houses; by clients in
hotels, motels and other residential type environments; bed and breakfast type
environments.
If the plug or cord is damaged, it must be replaced by Customer Services only to avoid
all risk.
FOR EUROPEAN MARKETS ONLY:
•
This appliance can be used by children aged from 8 years and above if they have been
given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. User cleaning and maintenance shall not be made
by children unless they are above 8 years old and supervised. Keep the appliance and
power cord away from children under 8 years of age.
•
Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are supervised or have been given
instruction concerning use of the appliance in a safe way and if they understand the
hazards involved.
•
Children shall not play with the appliance.
•
Always unplug the appliance when left unattended and before assembly, taking apart
or cleaning.
Surfaces marked with this symbol become hot during use (the symbol is present in
certain models only).
7
2. SAFETY WARNINGS
2.1 Symbols used in these instructions
Any other use is considered improper and thus dangerous. The
manufacturer is not liable for damage deriving from improper
use of the appliance.
Important warnings are identified by these symbols. It is vital to
respect these warnings.
2.3 Instruction for Use
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
Read this Instruction for Use carefully before using the appliance. Failure to follow this Instruction for Use may result in
burns or damage to the appliance.
The manufacturer is not liable for damage deriving from failure
to respect this Instruction for Use.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Please note:
Keep these instructions for future use. If the appliance is passed
to other persons, they must also be provided with this Instruction for Use.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Please note:
This symbol identifies important advice or information for the
user.
3. INTRODUCTION
Thank you for choosing this bean to cup espresso and cappuccino machine.
We hope you enjoy using your new appliance. Take a few minutes to read this Instruction for Use. This will avoid all risks and
damage to the appliance.
Danger!
This is an electrical appliance and may cause electric shock.
You should therefore follow these safety warnings:
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
• Unplug directly from the plug only. Never pull the cord as
you could damage it.
• To disconnect the appliance completely you must unplug it
from the mains socket.
• If the appliance is faulty, do not attempt to repair.
Turn it off, unplug from the mains socket and contact Customer Services.
• Before cleaning the appliance, turn it off, unplug from the
mains socket and allow to cool.
3.1 Letters in brackets
The letters in brackets refer to the legend in the description of
the appliance on pages 2-3.
3.2 Troubleshooting and repairs
In the event of problems, first try and resolve them by reading
the information given in sections “19. Displayed messages” and
“20. Troubleshooting”.
If this does not resolve the problem or you require further information, you should consult Customer Services by calling the
number given on the annexed "Customer Service" sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee. If repairs are required, contact
De’Longhi Customer Services only. The addresses are given in
the guarantee certificate provided with the machine.
Important:
Keep all packaging (plastic bags, polystyrene foam) away from
children.
Danger of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
When the appliance is in operation, the cup shelf could become
very hot.
2.2 Designated use
This appliance is designed and made to prepare coffee and heat
beverages.
8
4. DESCRIPTION
4.1 Description of the appliance
B11.
: Doppio+
: Beverage selection menu (other than directly selected beverages): Espresso Lungo, Ristretto, Steam, 2
Espresso, 2 Espresso Lungo, 2 Ristretto.
B13.
: My beverages selection menu. Unless previously programmed from the settings menu (“8.5 Program My
beverages”), the beverage is programmed directly the first
time you use the appliance.
B12.
(page 3 - A)
A1. Beans container lid
A2. Pre-ground coffee funnel lid
A3. Beans container
A4. Pre-ground coffee funnel
A5. Grinding adjustment dial
A6. Main switch
A7. Infuser door
A8.Infuser
A9. Power cord
A10. Condensate tray
A11. Coffee grounds container
A12. Cup tray
A13. Drip tray water level indicator
A14. Drip tray grille
A15. Drip tray
A16. Water tank lid
A17. Water tank
A18. Water softener filter housing
A19. Coffee spouts (adjustable height)
A20. Cappuccino maker
A21. Cappuccino maker selection ring
A22. Hot water and steam connection nozzle
A23.
button: turns the appliance on and off (standby)
A24. Cup shelf
4.2 Description of the accessories
(page 2 - C )
C1. Indicator paper
C2. Pre-ground coffee measure
C3.Descaler
C4. Water softener filter (certain models only)
5. BEFORE USE
5.1 Checking the appliance
After removing the packaging, make sure the product is complete and undamaged and that all accessories (C) are present. Do not use the appliance if it is visibly damaged. Contact
De’Longhi Customer Services.
5.2 Installing the appliance
Important!
When you install the appliance, you should respect the following safety warnings:
• The appliance gives off heat. After positioning the appliance on the worktop, leave a space of at least 3 cm between the surfaces of the appliance and the side and rear
walls and at least 15 cm above the coffee maker.
• Water penetrating the coffee machine could cause
damage.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the temperature could drop below freezing point.
• Arrange the cord (A9) in such a way that it cannot be damaged by sharp edges or contact with hot surfaces (e.g. electric hot plates).
Description of the touch screen
(page 2 - B )
A number of icons on the touch screen have a double function. This
is indicated in brackets in the description.
B1. Display: guides the user in using the appliance. The current
selection is at the centre between two dotted lines.
B2. ▼ Selection arrow (“ESC”: when programming beverages,
press to exit without saving the change)
B3. OK: to confirm the selection(During the first few seconds of
"espresso", "ristretto" or "espresso lungo" delivery, press for 2
cups)
B4. ▲ Selection arrow (“STOP” - When delivering/programming beverages, press to interrupt/programme)
B5.
/ESC: appliance settings menu
(When in the settings menu, it acts as the "ESC" to exit from
the selected function and go back to the main menu)
B6.
: hot water
B7.
: aroma selection
Directly selected beverages:
B8.
: Espresso
B9.
: Coffee
B10. : Long
5.3 Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
9
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
During rinsing, a little hot water comes out of the coffee spouts
(A19) and is collected in the drip tray (A15) underneath. Avoid
contact with splashes of water.
5.4 Setting up the appliance
•
To turn the appliance on, press the
button (A23) (fig.
5). The message "Heating Please wait" appears on the display (B1).
After heating, the message "Rinsing" is displayed, together with
a progress bar which gradually fills as preparation proceeds. As
well as heating the boiler, the appliance also heats the internal
circuits by circulating hot water.
The appliance is at temperature when the message "Select your
beverage" is displayed.
Please note:
Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee in the mill. The machine is, however, guaranteed to be
new.
You should customise water hardness as soon as possible following the instructions in section “15. Setting water hardness”.
•
1. Connect the appliance to the mains electricity supply (fig.
1) and make sure the main switch (A6) at the back of the
appliance is pressed down (fig. 1);
2. "Language": press the selection arrow (B2) until the required language is displayed between the two dotted
lines, then press OK (B3) to confirm.
Then follow the instructions indicated on the appliance display
(B1):
3.“Fill tank”: remove the water tank (A17 - fig. 2), fill to the
MAX line with fresh water (fig. 3A), then replace in the appliance (fig. 3B);
4. Place a container with a minimum capacity of 100 ml (fig.
4) under the cappuccino maker (A20);
5. "Water circuit empty, Fill water circuit, Hot water,
Confirm?";
6.Press OK to confirm. The appliance delivers water from the
cappuccino maker then goes off automatically.
The coffee machine is now ready for normal use.
•
•
7. TURNING THE APPLIANCE OFF
Whenever the coffee machine is turned off after being used to
make coffee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts
(A19). Avoid contact with splashes of water.
• To turn the appliance off, press the
button (A23 - fig.
5);
• The message "Turning off underway Please wait" appears
on the display (B1), then (if provided for) the appliance
performs a rinse cycle and goes off (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
• first turn the appliance off by pressing the
button
(fig. 5);
• release the main switch (A6) (fig. 1).
Please note:
The first time you use the appliance, you need to make 4-5
cups of coffee before it starts to give satisfactory results.
To enjoy your coffee even more and improve the performance of your appliance, we recommend installing a
water softener filter (C4) as described in section “16. Water
softener filter”. If your model is not provided with a filter,
you can request one from De'Longhi Customer Services.
Important!
Never press the main switch while the appliance is on.
8. MENU SETTINGS
The menu has 6 items, some divided into subgroups:
•Rinsing;
•Language;
• Maintenance:
- Descale,
- Install filter,
- (if a filter has been installed): Replace filter,
- (if a filter has been installed): Remove filter;
• Prg. beverages;
• Prg. My beverages;
• General:
- Set temperature,
- Water hardness,
- Auto-off,
6. TURNING THE APPLIANCE ON
Please note:
Before turning the appliance on, make sure the main switch
(A6) on the back of the appliance is pressed (fig. 1).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The appliance is ready for use only after completion of this cycle.
Danger of burns!
10
•
- Energy saving,
- Beep,
- Default beverages,
- Default values;
Statistics.
To select the operation you require, proceed as follows:
1.Press
(B5) to enter the "Settings" menu;
2. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two dotted lines;
3.Press OK (B3) to confirm;
4. Press the selection arrows to display the operation to be
performed;
5.Press OK to confirm and perform the operations as described in the corresponding sections.
8.1 Rinsing
Use this function to deliver hot water from the coffee spouts
(A19) to clean and heat the appliance’s internal circuit.
Place a container with a minimum capacity of 100ml under the
coffee spouts.
8.4 Program beverages
The appliance is set by default to automatically deliver standard quantities. To change these quantities and customise the
directly selected beverages and
(B12), proceed as
follows:
1. Press
(B5) to enter the "Settings" menu;
2. Press the selection arrows (B2 and B4) until "Prg. beverages" is displayed between the two dotted lines;
3. Press OK (B3) to confirm: the appliance lists the beverages
you can customise;
4. Press the selection arrows until the beverage you want to
customise is displayed, then press OK to confirm;
5. Beverages with coffee: "Program aroma" appears on
the display: press the selection arrows (B2 and B4) or
(B7) until the required aroma is selected (see section “9.4
Temporarily varying the coffee aroma”), then press OK.
"Program coffee" appears on the display together with a
bar which gradually fills as delivery progresses. When the
required quantity is reached, press OK;
Hot water: press OK. Delivery begins: press OK when the
required quantity is reached.
6. "Save parameters?": to save the settings, press OK (otherwise press
/ESC - B2 or B5).
7. "Parameters saved" (or "Parameters not saved"). The appliance is ready for use again.
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
To perform a rinse, proceed as follows:
1. Press
(B5) to enter the "Settings" menu;
2.Press OK (B3) to confirm "Rinsing";
3. After a few seconds, hot water is delivered from the coffee
spouts to clean and heat the appliance’s internal circuit. A
progress bar is displayed and fills gradually as preparation
proceeds;
4. To interrupt, press the arrow corresponding to "STOP" (B4).
•
•
Please note!
If the appliance is not used for more than 3-4 days, when
switched on again, we strongly recommend performing
2/3 rinses before use;
After cleaning, it is normal for the coffee grounds container
(A11) to contain water.
8.2 Language
To modify the language of the display (B1), proceed as follows:
1. Press
(B5) to enter the "Settings" menu;
2. Press the selection arrows (B2 and B4) until "Language" is
displayed between the two dotted lines;
3. Press OK (B3). The available languages are displayed;
4. Press the selection arrows until the required language is
displayed between the two dotted lines;
5. Press OK to confirm;
6. The appliance goes back to the "Settings" menu;
7. Press
/ESC to exit the menu.
8.5 Program My beverages
Follow the procedures described in the previous section “8.4 Program beverages”to customise the beverages in the "
" (B13) or proceed with direct programming, as described in
section “11. Programming and selecting”.
8.6 General
8.3 Maintenance
Here you can find the settings to customise the basic functions
of the appliance:
1. Press
(B5) to enter the "Settings" menu;
2. Press the selection arrows (B2 and B4) until "General" is
displayed between the two dotted lines;
Here you can find all the maintenance operations required by
the appliance over time:
• Descale: For instructions on descaling, see section “14.
Descaling”.
• Install filter: For instructions on how to install the filter
(C4), see section “16.1 Installing the filter”.
11
3. Press OK (B3) to confirm and select the required item with
the selection arrows. Then follow the instructions for each
setting.
The display goes back to the previous screen.
• Default beverages:
Use this function to reset the default values for all the beverages, or the individual beverages programmed previously. Select
the beverage, then proceed as follows:
4. Select "All" to reset the aroma and quantity settings to the
default values, or select the required beverage, then press
OK;
5. "Reset?": to reset the default values, press OK.
6. "Reset complete": the appliance confirms the reset and
goes back to the previous screen.
To reset another beverage, repeat from point 4 or to exit, press
/ESC (B5).
• Set temperature:
To modify the temperature of the water used to make the coffee,
proceed as follows:
4.Press OK (B3). The current value appears on the display
(B1) and the "New" value flashes;
5. Select the new value you want to set using the selection
arrows (B2 or B4);
6. When the required value (low, medium, high, maximum)
has been selected, press OK.
The display goes back to the previous screen.
• Water hardness:
For instructions on identifying and setting water hardness, see
section “15. Setting water hardness”.
• Default values:
Use this function to reset all the appliance and beverage settings (apart from the language which remains as selected the
first time the appliance was used). Select the item, then proceed
as follows:
4. "Reset?"; press OK;
5. "Reset complete": the appliance confirms the reset and
goes back to the previous screen.
To exit, press
/ESC (B5).
• Auto-off (standby):
Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours
4.Press OK. The current value appears on the display (B1) and
the "New" value flashes;
5. Select the new value you want to set using the selection
arrows (B2 or B4);
6. When the required time has been selected, press OK.
The display goes back to the previous screen.
8.7 Statistics
This displays statistics relating to the machine. To display the
statistics, proceed as follows:
1.Press
(B5) to enter the "Settings" menu;
2. Press the selection arrows (B2 and B4) until "Statistics" is
displayed between the two dotted lines;
3.Press OK (B3): statistics on the appliance are displayed, use
the selection arrows to scroll through the items;
4. Then press
/ESC (B5) to exit.
To go back to the main screen, press
/ESC.
• Energy saving:
Use this function to enable or disable energy saving. When enabled, the function reduces energy consumption in compliance
with European regulations.
To disable or enable "Energy Saving", proceed as follows:
4.Press OK. The current state ("Enabled" or "Disabled") and
the operation to be performed ("Disable?" or "Enable?") is
displayed. Press OK to confirm;
5.Press OK to disable or enable the function.
The display goes back to the previous screen.
•
•
9. MAKING COFFEE
9.1 Adjusting the coffee mill
Please note!
when the function is enabled, the "ECO" symbol appears
on the display.
When in energy saving mode, a few seconds elapse before
the first coffee, cappuccino or milk-based coffee is delivered as the appliance must heat up again.
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that the
coffee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by calibrating
the coffee grinding using the adjustment dial (A5) (fig. 6).
•Beep:
Use this function to enable or disable the beep. Proceed as
follows:
4.Press OK. The current state ("Enabled" or "Disabled") and
the operation to be performed ("Disable?" or "Enable?") is
displayed. Press OK to confirm;
5.Press OK to disable or enable the function.
Please note:
The grinding adjustment dial must only be turned when the
coffee mill is in operation.
12
If the coffee is delivered too slowly or not
at all, turn one click clockwise towards 7.
For fuller bodied creamier coffee, turn
one click anticlockwise towards 1 (do not
turn more than one click at a time otherwise the coffee could be delivered a drop
Beverages with coffee selectable from the
(B12)
at a time).
These adjustments will only be evident after at least 2 cups of
coffee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
9.2 Tips for a hotter coffee
For hotter coffee, you should:
• perform a rinse cycle by pressing /ESC (B15);
• warm the cups with hot water using the hot water function
(see section “12. Delivering hot water”);
• increase the coffee temperature in the "Settings" menu
(see section “8.6 General”).
Directly selected beverages
Coffee (B9)
≃ 40 ml
from ≃30
to
≃ 80ml
≃ 180 ml
from ≃100
a ≃240cc
≃ 160 ml
from ≃115
to ≃250cc
≃ 120 ml
from ≃80
to ≃180cc
Long (B10)
Doppio+
(B11)
≃ 30 ml
from ≃20
to ≃40cc
2 Espresso
≃ 40 ml x
2 cups
--
+
2 Espresso
Lungo
≃ 120 ml
x 2 cups
--
+
2 Ristretto
≃ 30 ml x
2 cups
--
+
Please note:
• You can prepare 2 cups of RISTRETTO, ESPRESSO or ESPRESSO
LUNGO coffee at the same time by pressing "2X" (B3) during preparation of single beverages (the image is displayed
for a few seconds at the start of preparation).
• While the machine is making coffee, delivery can be interrupted at any time by pressing the selection arrow corresponding to "STOP" (B4).
• At the end of delivery, to increase the quantity of coffee in
the cup, just press and hold (within 3 seconds) one of the
coffee icons (B8 to B11).
Once the coffee has been made, the appliance is ready to make
the next beverage.
Fill the container (A3) (fig. 7) with coffee beans;
Place under the coffee spouts (A19):
- 1 cup, if you want to make 1 coffee (fig. 8);
- 2 cups if you want 2 coffees.
Lower the spouts as near as possible to the cup. This makes
a creamier coffee (fig. 9);
4. Then select your required coffee:
Espresso (B8)
Ristretto
+
1.
2.
3.
Programmable
quantity
from ≃80
to ≃180c
+
Important!
Do not use green, caramelised or candied coffee beans as they
could stick to the coffee mill and make it unusable.
Quantity
≃ 120 ml
5. Preparation begins. A progress bar appears on the display
(B1) and gradually fills as preparation proceeds.
9.3 Making automatic recipes using coffee
beans
Recipe
Espresso
Lungo
•
Default
aroma
•
•
•
+
Please note:
Various alarm messages could be displayed while using the
appliance (fill tank, empty grounds container, etc.). Their
meaning is explained in section “19. Displayed messages”.
For hotter coffee, see section “9.2 Tips for a hotter coffee”.
If the coffee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in section “20.
Troubleshooting”.
To customise the beverages according to personal taste,
see sections “8.4 Program beverages” and “8.5 Program My
beverages”.
9.4 Temporarily varying the coffee aroma
+
+
+
13
To temporarily vary the aroma of the coffee in the automatic
recipes, press
(B7):
AUTO
Custom (if programmed) /
Standard
EXTRA LIGHT
Espresso Lungo
Ristretto
≃ 30 ml
5. Preparation begins. The beverage selected appears on the
display together with a progress bar which gradually fills
as preparation proceeds.
LIGHT
MEDIUM
STRONG
+
+
+
+
+
•
•
Important! Making LONG coffee
:
Halfway through preparation, the message "Add pre-ground
coffee" appears on the display (B1). Add one level measure of
pre-ground coffee and press OK (B3).
X-STRONG
(see “9.5 Making coffee
using pre-ground coffee”)
Please note:
If "Energy Saving" mode is active, you may have to wait a few
seconds before the first coffee is delivered.
Please note:
The variation in aroma is not saved and the next time a
beverage is delivered automatically, the appliance selects
the default value ( AUTO).
If a few seconds elapse between temporary customising of
the aroma and delivery of the beverage, the aroma returns
to the default value ( AUTO).
10. MAKING CAPPUCCINO AND HOT MILK (NOT
FROTHED)
Danger of burns!
During preparation steam is given off. Take care to avoid scalds.
1. When preparing cappuccino, make the coffee in a large
cup;
2. Fill a container (preferably one with a handle to avoid
scalding) with about 100 grams of milk for each cappuccino. In choosing the size of the container, bear in mind that
the milk doubles or triples in volume;
9.5 Making coffee using pre-ground coffee
+
•
•
Important!
Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
+
it. This could damage the appliance.
Never use more than 1 level measure (C2) or it could dirty
the inside of the coffee machine or block the funnel (A4).
Please note:
If you use pre-ground coffee, you can only make one cup of
coffee at a time.
1. Press the
icon (B7) repeatedly until " " appears
on the display (B1).
2. Make sure the funnel is not blocked, then add one level
measure of pre-ground coffee (fig. 10).
3. Place a cup under the coffee spouts (A19) (fig. 8).
4. Then select your required coffee:
Quantity
Espresso (B8)
≃ 40 ml
Coffee (B9)
≃ 180 ml
Long (B10)
≃ 160 ml
Please note:
For a richer denser froth, use skimmed or partially
skimmed milk at refrigerator temperature (about 5°C). To
avoid milk with poor froth or large bubbles, always clean
the cappuccino maker (A20) as described in section “10.2
Cleaning the cappuccino maker after use”.
3. Make sure the cappuccino maker selection ring (A21) is
positioned downwards in the "CAPPUCCINO" position (fig.
11);
4. The cappuccino maker can be turned slightly outwards to
allow containers of any size to be used.
Directly selected beverages
Recipe
≃ 120 ml
Important!
Never use force to turn the cappuccino maker (fig. 12). It
could break!
5. Immerse the cappuccino maker in the milk container.
Never immerse the black ring;
6.Press
(B12);
7. Press the selection arrows (B2 and B4) until "Steam" is displayed between the two dotted lines;
8.Press OK (B5). "Steam" is displayed. After a few seconds,
steam is delivered from the cappuccino maker, giving
Beverages with coffee selectable from the
(B12)
14
the milk a creamy frothy appearance and making it more
voluminous;
9. For a creamier froth, rotate the container with slow movements in an upward direction;
10. When the required temperature is obtained, interrupt
steam delivery by pressing the selection arrow corresponding to "STOP".
11. “
” PROGRAMMING AND SELECTING
In
you can select beverages customised to your personal tastes. If the beverages have not yet been programmed,
the appliance will request the customisation procedure before
proceeding with delivery:
1. Press
(B13);
2. Press the selection arrows (B2 and B4) until the required
beverage is displayed between the two dotted lines;
Unprogrammed beverages:
3. Press OK (B3) to select;
4. "Program aroma" appears on the display. Press the selection arrows (B2 and B4) or
(B7) until the required
aroma is selected. Press OK. "Program coffee" appears on
the display together with a bar which gradually fills as delivery progresses. When the required quantity is reached,
press OK.
5. The appliance then makes the coffee. Press OK to interrupt
delivery when the required quantity of coffee is reached.
6. "Save parameters?": to save the settings, press OK (otherwise press ESC - B2 or B5).
8. "Parameters saved" (or "Parameters not saved"). The appliance is ready for use again.
Programmed beverages:
3. Press OK (B3) to select;
4. Preparation begins according to the previously programmed settings.
Danger of burns!
Stop steam delivery before removing the container with the
frothed milk to avoid burns caused by splashes of boiling milk.
11. Add the milk froth to the coffee prepared previously. The
cappuccino is ready. Sweeten to taste and, if desired, sprinkle the froth with a little cocoa powder.
Please note!
If “Energy saving” is active, you may have to wait a few seconds
before steam is delivered.
10.1 Making hot milk (not frothed)
To make hot milk without froth, proceed as described in the
above section, but with the cappuccino maker selection ring
(A21) positioned upwards in the "HOT MILK" position.
10.2 Cleaning the cappuccino maker after use
Clean the cappuccino maker (A20) each time you use it to avoid
the build-up of milk residues or blockages.
Please note:
Two cups of a beverage can only be selected when the corresponding single beverages have been programmed.
Danger of burns!
When cleaning the cappuccino maker, a little hot water is delivered. Avoid contact with splashes of water.
12. DELIVERING HOT WATER
Important! Danger of burns.
Never leave the machine unattended while delivering hot water.
The cappuccino maker (A20) becomes hot while water is being
delivered and must be held by the black ring (A21) only.
1. Deliver a little water by pressing the
icon (B6 - fig.13).
To interrupt, press the selection arrow (B4) corresponding
to "STOP".
2. Wait a few minutes for the cappuccino maker to cool down.
Turn the cappuccino maker downwards to remove it (fig.
14).
3. Move the selection ring (A21) upwards (fig. 15).
4. Remove the connection nozzle downwards (A22 - fig. 16).
5. Make sure the two holes shown by the arrow in fig. 17 are
not blocked. If necessary, clean with a pin.
6. Replace the connection nozzle, move the selection ring
downwards and put the cappuccino maker back on the
nozzle (fig. 18), turning it clockwise and pushing it upwards
until it is attached.
1. Place a container under the cappuccino maker (A20) (as
close as possible to avoid splashes).
2.Press
(B6 - fig. 13). "HOT WATER” appears on the display (B1), together with a progress bar which fills gradually as preparation proceeds.
4. The machine delivers about 250 ml of hot water, then delivery stops automatically. To interrupt hot water delivery
manually, press the selection arrow (B4) corresponding to
"STOP" again.
Please note!
If “Energy Saving” is active, you may have to wait a few seconds
before hot water and steam are delivered.
15
13. CLEANING
13.1 Cleaning the machine
To clean (with the machine on):
• Remove the drip tray (A15) (fig. 19), empty and clean.
• Empty the grounds container (A11) and clean thoroughly
to remove all residues left on the bottom.
• Check the condensate tray (A10) (red) and empty if
necessary.
The following parts of the machine must be cleaned regularly:
- the appliance’s internal circuit;
- coffee grounds container (A11);
- drip tray (A15) and condensate tray (A10);
- water tank (A17);
- coffee spouts (A19);
- pre-ground coffee funnel (A4);
- infuser (A8), accessible after opening the infuser door (A7);
- cappuccino maker (A20 - section “10.2 Cleaning the cappuccino maker after use”);
- touch screen (B).
13.4 Cleaning the drip tray and condensate tray
Important!
The drip tray (A15) is fitted with a level indicator (A13) (red)
showing the level of water it contains (fig. 20). Before the indicator protrudes from the cup tray (A12), the drip tray must
be emptied and cleaned otherwise the water may overflow the
edge and damage the appliance, the surface it rests on or the
surrounding area.
To remove the drip tray:
1. Remove the drip tray and coffee grounds container (A11)
(fig. 19);
2. Remove the cup tray (A12) and drip tray grille (A14), then
empty the drip tray and grounds container and wash all
components;
3. Check the red condensate tray (A10) and empty if
necessary;
4. Replace the drip tray complete with grille and grounds
container.
Important!
Do not use solvents, abrasive detergents or alcohol to clean
the coffee machine. With De’Longhi superautomatic coffee
machines, you need not use chemical products to clean the
machine.
• None of the components of the appliance can be washed in a
dishwasher with the exception of the drip tray grille (A14).
• Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
•
13.2 Cleaning the machine's internal circuit
If the appliance is not used for more than 3/4 days, before using
it again, we strongly recommend switching it on and:
- performing 2/3 rinse cycles (see section “8.1 Rinsing”);
- delivering hot water for a few seconds (section “12. Delivering hot water”).
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coffees, the grounds
container may fill up more than expected and clog the machine.
Please note:
After cleaning, it is normal for the coffee grounds container
(A11) to contain water.
13.5 Cleaning the inside of the coffee machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned off
(see section “7. Turning the appliance off”) and unplugged from
the mains power supply. Never immerse the coffee machine in
water.
1. Check regularly (about once a month) that the inside of the
appliance (accessible after removing the drip tray (A15)
is not dirty. If necessary, remove coffee deposits with the
brush supplied and a sponge;
2. Remove all the residues with a vacuum cleaner (fig. 21).
13.3 Cleaning the coffee grounds container
When "Empty grounds container" appears on the display (B1),
the grounds container must be emptied and cleaned. The appliance cannot be used to make coffee until you have cleaned
the grounds container (A11). Even if not full, the empty grounds
container message appears on the display 72 hours after the
first coffee has been prepared. For the 72 hours to be calculated
correctly, the machine must never be turned off with the main
switch (A6).
Important! Danger of burns
If you make a number of cappuccinos one after the other, the
metal cup tray (A12) becomes hot. Wait for it to cool down before touching it and handle it from the front only.
13.6 Cleaning the water tank
1. Clean the water tank (A17) regularly (about once a month)
and whenever you replace the water softener filter (C4) (if
provided) with a damp cloth and a little mild washing up
liquid;
16
2. Remove the filter (C4) (if present) and rinse with running
water;
3. Replace the filter (if provided), fill the tank with fresh
water and replace the tank;
4. (Models with water softener filter only) Deliver about
100ml of water.
9. Close the infuser door;
10. Put the water tank back.
14. DESCALING
•
13.7 Cleaning the coffee spouts
•
1. Clean the coffee spouts (A19) regularly with a sponge or
cloth (fig. 22A);
2. Check that the holes in the coffee spouts are not blocked.
If necessary, remove coffee deposits with a toothpick (fig.
22B).
Important!
Before use, read the instructions and the labelling on the
descaler pack.
You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may result in faults not covered by the manufacturer's guarantee.
Descale the machine when "Descale, ESC to cancel, OK to descale (∼45 minutes)" appears on the display (B1). To descale immediately, press OK (B3) and follow the instructions from point
6. To descale the appliance later, press ESC (B5). The symbol
on the display reminds you that the appliance needs descaling.
To access the descaling menu:
1. Turn the appliance on and wait until it is ready for use;
2.Press
(B5) to enter the "Settings" menu;
3. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two dotted lines. Press OK (B3);
4.Press OK to select "Descale";
5. Confirm? (∼45 minutes)”. Press OK to confirm;
6. "Remove filter": extract the water tank (A17), remove the
water softener filter (C4) (if present) and empty the water
tank. Press OK;
7. "Pour descaler and water into tank": Pour the descaler into
the tank up to level A (corresponding to a 100ml pack)
marked on the inner surface of the tank, then add water
(one litre) up to level B (fig. 26) and put the water tank
back. Press OK;
8. "Empty drip tray": Remove, empty and replace the drip
tray (A15) and grounds container (A11). Press OK;
13.8 Cleaning the pre-ground coffee funnel
Check regularly (about once a month) that the pre-ground
coffee funnel (A4) is not blocked. If necessary, remove coffee
deposits with a brush.
13.9 Cleaning the infuser
The infuser (A8) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned off (see section
“7. Turning the appliance off”);
2. Remove the water tank (A17);
3. Open the infuser door (A7) (fig. 23) on the right side of the
appliance;
4. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (fig. 24);
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap;
Please note:
In certain cases, a cooling process lasting several seconds may
take place before moving on to the next point.
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID - NO DISH WASHER
Clean the infuser without using washing up liquid as it
could be damaged.
6. Use the brush to remove any coffee residues left in the infuser housing, visible through the infuser door;
7. After cleaning, replace the infuser by sliding it onto the internal support, then push the PUSH symbol fully in until it
clicks into place;
9. "Place 1.8L container empty under spouts": Place an empty
container with a minimum capacity of 1.8 litres under the
cappuccino maker (A20) and coffee spouts (A19) (fig. 27).
Press OK;
Important! Danger of burns
Hot water containing acid flows out of the coffee spouts and
hot water spout. Take care to avoid contact with splashes of this
solution.
Please note:
If the infuser is difficult to insert, before insertion, adapt it to the
right size by pressing the two levers (fig. 25).
8. Once inserted, make sure the two coloured buttons have
snapped out;
10. "Descaling underway": The descale programme starts and
the descaler liquid comes out of the cappuccino maker and
17
coffee spouts. A series of rinses and pauses is performed
automatically to remove all the scale residues inside the
coffee machine;
After about 35 minutes, descaling stops;
11. "Rinse tank and fill with water": the appliance is now
ready to rinse with fresh water. Empty the container used
to collect the descaler solution. Extract the water tank,
empty, rinse under running water, fill with fresh water up
to the MAX level and put back in the appliance. Press OK;
12. "Place 1.8L container empty under spouts": place the container used to collect the descaler solution empty under
the coffee spouts and hot water spout (fig. 27) and press
OK";
13. "Rinsing Confirm?": press OK;
14. "Rinsing underway": hot water is delivered first from the
coffee spouts, then from the cappuccino maker;
15. When the water in the tank has run out, empty the container used to collect the rinsing water;
16. "Rinse tank and fill with water": extract the water tank and
fill with fresh water up to the MAX level. Press OK;
14. "Insert filter": put the water softener filter (if removed)
back in its housing in the water tank, and replace the tank
in the appliance. Press OK;
15. "Place 1.8L container empty under spouts": Place the container used to collect the descaler solution empty under
the cappuccino maker. Press OK;
16. "Rinsing Confirm?": press OK.
17. "Rinsing underway". Hot water comes out of the cappuccino maker;
18. "Empty drip tray": At the end of the second rinse, remove,
empty and replace the drip tray (A15) and grounds container (A11). Press OK;
19. "Descale complete": press OK;
20. "Fill tank": empty the container used to collect the rinse
water, remove the water tank and fill with fresh water up
to the MAX level, then put back in the appliance.
Descaling is complete.
The descale message is displayed after a period of time established according to water hardness.
The machine is set by default for a hardness level of 4. The machine can also be programmed according to the hardness of the
mains water in the various regions so that the machine needs to
be descaled less often.
15.1 Measuring water hardness
1. Remove the "TOTAL HARDNESS TEST" indicator paper (C1)
from its pack (attached to the English instructions);
2. Immerse the paper completely in a glass of water for one
second;
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to 1
level;
soft water (level 1)
slightly hard water (level 2)
hard water (level 3)
very hard water (level 4)
15.2 Setting water hardness
1.Press
(B5) to enter the "Settings" menu;
2. Press the selection arrows (B2 and B4) until "General" is
displayed between the two dotted lines. Press OK (B3;
3. Press the selection arrows until "Water hardness" is displayed, then press OK;
4. The current selection appears on the display and the new
selection flashes. Press the selection arrows until the required new selection is displayed. Press OK.
The new level is saved and the appliance goes back to the "General" menu.
Press /ESC (B5) twice to go back to the main screen.
Please note!
If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
• After descaling, it is normal for the grounds container
(A11) to contain water;
• If the water tank has not been filled to the MAX level, at
the end of descaling, the appliance requests a third rinse to
guarantee that the descaler solution has been completely
eliminated from the machine's internal circuits.
•
16. WATER SOFTENER FILTER
Certain models are fitted with a water softener filter (C4). If this
is not the case with your model, you are recommended to purchase one from De’Longhi Customer Services.
To use the filter correctly, follow the instructions below.
16.1 Installing the filter
1. Remove the filter (C4) from the packaging. The date indicator disk varies according to the filter provided.
2. Turn the date indicator disk (fig. 28) until the next 2
months of use are displayed.
15. SETTING WATER HARDNESS
18
7. "Hot water, Confirm?": Position a container under the cappuccino maker (A20) (min. capacity: 500ml), then press
OK;
8. The appliance begins hot water delivery and the message
"Please wait" is displayed;
9. After the flow of hot water stops, the appliance automatically resets to "Ready for coffee" status.
The new filter is now active and you can use the coffee machine.
Please note
The filter lasts about two months if the appliance is used normally. If the coffee machine is left unused with the filter installed, it will last a maximum of 3 weeks.
3. To activate the filter, run tap water through the hole in the
filter as shown in fig. 29 until water comes out of the openings at the side for more than a minute.;
4. Extract the tank (A17) from the appliance and fill with
water;
5. Insert the filter in the water tank and immerse it completely for about ten seconds, sloping it and pressing it lightly to
enable the air bubbles to escape (fig. 30).
6. Insert the filter in the filter housing (A18) and press as far
as it will go (fig. 31);
7. Close the tank with the lid (A16 - fig. 32), then replace the
tank in the machine;
When you install the filter, you must notify the appliance of its
presence.
8.Press
(B5) to enter the "Settings" menu;
9. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two dotted lines. Press OK (B3);
10. Press the selection arrows until "Install filter" is displayed,
then press OK;
11. Confirm?": press OK;
12. "Hot water, Confirm?": Position a container under the cappuccino maker (A20) (min. capacity: 500ml), then press
OK;
13. The appliance begins hot water delivery and the message
"Please wait" is displayed;
14. After the flow of hot water stops, the appliance automatically resets to "Ready for coffee" status.
The filter is now active and you can use the coffee machine.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the filter even if
the message has not yet been displayed.
16.3 Removing the filter
If you want to use the appliance without the filter (C4), you
must remove it and notify the appliance of its removal. Proceed
as follows:
1. Extract the tank (A17) and exhausted filter;
2. Press
(B5) to enter the "Settings" menu;
3. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two dotted lines. Press OK (B3);
4. Press the selection arrows until "Remove filter" is displayed, then press OK;
5. "Confirm?": press OK to confirm removal. The appliance
goes back to the "Maintenance" menu;
Press
/ESC (B5) to exit the menu.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the filter even if
the message has not yet been displayed.
17. TECHNICAL DATA
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1450W
Pressure: 1.5MPa (15 bars)
Max. water tank capacity: 1.8 L
Size LxDxH: 240x440x360 mm
Cord length:
1150 mm
Weight: 9.3 kg
Max. beans container capacity:
300 g
16.2 Replacing the filter
Replace the filter (C4) when "Replace filter, ESC to cancel, OK to
replace" appears on the display (B1). To replace immediately,
press OK (B3) and follow the instructions from point 7. To replace later, press
/ESC (B5). The symbol on the display
reminds you that the filter needs replacing.
To replace the filter, proceed as follows:
1. Extract the tank (A17) and exhausted filter;
2. Take the new filter out of its packet and proceed as illustrated in points 2, 3, 4, 5, 6 and 7 in the previous section;
3. Press
(B5) to enter the "Settings" menu;
4. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two dotted lines. Press OK;
5. Press the selection arrows until "Replace filter" is displayed, then press OK;
6. Confirm?": press OK;
This appliance conforms to EC Regulation 1935/2004
on materials and articles intended to come into contact
with food.
18. DISPOSING OF THE APPLIANCE
The appliance must not be disposed of with household waste, but taken to an authorised waste separation and recycling centre.
19
19. DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
REMEDY
Fill tank
Insufficient water in the tank (A17).
Fill the tank with water and/or insert it correctly, pushing it as far as it will go until it clicks
into place (fig. 3B).
Insert tank
The tank (A17) is not correctly in place.
Insert the tank correctly and press as far as it
will go (fig. 3B).
Empty grounds container
The grounds container (A11) is full.
Empty the grounds container and drip tray
(A15), clean and replace. Important: when
removing the drip tray, the grounds container must be emptied, even if it contains few
grounds. If this is not done, when you make
the next coffees, the grounds container may fill
up more than expected and clog the machine.
Insert grounds container
After cleaning, the grounds container (A11) Remove the drip tray (A15) and insert the
has not been replaced.
grounds container.
Add pre-ground coffee
The "pre-ground coffee" function has been se- Place pre-ground coffee in the funnel (fig. 10)
lected without placing any pre-ground coffee or deselect the "pre-ground" function.
in the funnel (A4).
A LONG coffee with pre-ground coffee has Put one level measure of pre-ground cofbeen requested
fee into the pre-ground coffee funnel (A4)
and press OK (B3) to continue and complete
preparation.
Fill beans container
Ground too fine
Adjust mill
The coffee beans have run out.
Fill the beans container (A3) (fig. 7).
The pre-ground coffee funnel (A4) is clogged.
Empty the funnel with the help of a brush as
described in section “13.8 Cleaning the preground coffee funnel”.
The grinding is too fine and the coffee is deliv- Repeat coffee delivery and turn the grinding
ered too slowly or not at all.
adjustment dial (A5) (fig. 6) one click clockwise
towards 7 while the coffee mill is in operation. If
after making at least 2 coffees delivery is still too
slow, repeat the correction procedure, turning
the grinding adjustment dial another click until
delivery is correct (see section “9.1 Adjusting the
coffee mill”). If the problem persists, make sure
the water tank (A17) is fully inserted.
If the water softener filter (C4) is present, an Deliver a little water from the cappuccino
air bubble may have been released inside the maker (A20) until it flows out normally.
circuit, obstructing delivery.
Less coffee
Too much coffee has been used.
Insert infuser assembly
The infuser (A8) has not been replaced after Insert the infuser as described in section “13.9
cleaning.
Cleaning the infuser”).
20
Select a lighter taste by pressing
(B7) or
reduce the quantity of pre-ground coffee.
Water circuit empty
Fill water circuit
Hot water
Confirm?
The water circuit is empty.
Press OK (B3) and deliver water from the cappuccino maker (A20) until it flows out normally. If the problem persists, make sure the water
tank (A17) is fully inserted.
Descale
ESC to cancel
OK to descale
(∼45 minutes)
The machine must be descaled.
The descaling procedure described in section
“14. Descaling” needs to be performed.
Replace filter
ESC to cancel
OK to replace
The water softener filter (C4) is exhausted.
Replace the filter or remove it as described in
section “16. Water softener filter”.
General alarm
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly,
as described in section “13. Cleaning”. If the
message is still displayed after cleaning, contact Customer Services.
The water softener filter (C4) is exhausted and Replace the filter or remove it as described in
must be replaced or removed.
section “16. Water softener filter”.
ECO
The machine must be descaled.
The descaling procedure described in section
“14. Descaling” needs to be performed.
Energy saving is enabled.
To disable energy saving, proceed as described
in section “8.6 General” - “•
Energy
saving:”
21
20. TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
PROBLEM
POSSIBLE CAUSE
REMEDY
The coffee is not hot.
The cups were not preheated.
Warm the cups by rinsing them with hot
water (Please note: you can use the hot water
function).
The internal circuits of the appliance have Before making coffee, heat the infuser by
cooled down because 2/3 minutes have performing a rinse cycle (see section “8.1
elapsed since the last coffee was made.
Rinsing”).
A low coffee temperature is set.
The coffee is weak or not The coffee is ground too coarsely.
creamy enough.
Set a higher coffee temperature in the menu.
Turn the grinding adjustment dial (A5) one
click anticlockwise towards 1 while the coffee
mill is in operation (fig. 7). Continue one click
at a time until coffee delivery is satisfactory.
The effect is only visible after delivering 2
coffees (see section “9.1 Adjusting the coffee
mill”).
The coffee is unsuitable.
Use pre-ground coffee for espresso machines.
The coffee is delivered too
slowly or a drop at a time.
The coffee is ground too finely.
Turn the grinding adjustment dial (A5) one
click clockwise towards 7 while the coffee mill
is in operation (fig. 7). Continue one click at a
time until coffee delivery is satisfactory. The
effect is only visible after delivering 2 coffees
(see section “9.1 Adjusting the coffee mill”).
The appliance will not make
coffee
The appliance has detected impurities in its Wait for the appliance to be ready for use again
internal circuits. "Please wait" is displayed.
and reselect the required beverage. Contact
Customer Services if the problem persists.
Coffee does not come out of
one or both of the spouts.
The coffee spouts (A19) are blocked.
The appliance does not come It is not plugged into the mains socket.
on
The main switch (A6) is not turned on.
The infuser
extracted
cannot
Clean the spouts with a toothpick (fig. 24B).
Plug into the mains socket (fig. 1).
Place the main switch in the I position (fig. 2).
be The appliance has not been turned off correctly Turn the appliance off by pressing the
button (A23) (fig. 5) (see section “7. Turning
the appliance off”).
At the end of descaling, the During the two rinse cycles, the water tank has Follow the instructions displayed by the appliappliance requests a third not been filled to the MAX level.
ance, but first empty the drip tray to avoid the
rinse
water overflowing.
22
The frothed milk has large The milk is not cold enough or is not You should ideally use skimmed or semibubbles
semi-skimmed
skimmed milk at refrigerator temperature
(about 5°C). If the result is not as you wished,
try changing brand of milk.
The milk is not frothed
The cappuccino maker (A20) is dirty
Clean as described in section “10.2 Cleaning
the cappuccino maker after use”.
The ring on the cappuccino maker (A21) is in Push the ring into the “CAPPUCCINO” position
the “HOT MILK” position.
(fig. 11).
Steam delivery stops
A safety device stops steam delivery
Wait a few minutes and then enable the steam
function again.
21. ELECTRICAL REQUIREMENTS
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you
are in any doubt about your supply contact your local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children
might find it and plug it into a supply socket - with the obvious consequent danger.
Please note: We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in
use.
IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
Green and Yellow to Earth
GREEN AND YELLOW EARTH
BLUE NEUTRAL
BROWNLIVE
13 amp Fuse
Blue to
neutral
Brown to live
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or
by the earth symbol
or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains
lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified
electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should
only be replaced with a flexible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a
replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse
recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
23
Download PDF
Similar pages