qf-cast-iron-saphire-owner-manual

Owner’s Manual
Care and Operation
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
Contact your dealer with questions regarding installation, operation or service.
NOTICE: DO NOT discard this manual!
R
Models:
WARNING: If the information in these
instructions is not followed exactly, a fire or
explosion may result causing property damage,
personal injury, or death.
- DO NOT store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
SAPH-MBK-IPI
SAPH-MBK-IPIL
SAPH-D-PMH-IPI
SAPH-D-PMH-IPIL
SAPH-D-MBK-IPI
SAPH-D-MBK-IPIL
SAPH-D-CSB-IPI
SAPH-D-CSB-IPIL
- What to do if you smell gas • DO NOT try to light any appliance.
• DO NOT touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
- Installation and service must be performed by a qualified
installer, service agency, or the gas supplier.
! DANGER
Solitaire
1
Cabinet Style
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with
this appliance and shall be installed for the
protection of the children and other at-risk
individuals.
This appliance may be installed as an OEM installation
in manufactured home (USA only) or mobile home and
must be installed in accordance with the manufacturer’s
instructions and the manufactured home construction
and safety standard, Title 24 CFR, Part 3280 or Standard
for Installation in Mobile Homes, CAN/CSA Z240MH, in
Canada.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
This appliance is only for use with the type(s) of gas
indicated on the rating plate.
See Installation Manual for location of additional Commonwealth
of Massachusetts requirements.
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
1
Welcome
Read this manual before operating this appliance.
Please retain this Owner’s Manual for future reference.
Read the Installation Manual before making any installation or finishing changes.
A.Congratulations
This owner’s manual should be retained for future reference.
We suggest that you keep it with your other important
documents and product manuals.
Congratulations on selecting a Quadra-Fire gas stove, an
elegant and clean alternative to wood burning stoves. The
Quadra-Fire gas stove you have selected is designed to
provide the utmost in safety, reliability, and efficiency.
The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.
As the owner of a new stove, you’ll want to read and carefully
follow all of the instructions contained in this owner’s manual.
Pay special attention to all cautions and warnings.
Your new Quadra-Fire gas stove will give you years of durable
use and trouble-free enjoyment. Welcome to the Quadra-Fire
family of stove products!
Local Dealer Information
DEALER: Fill in
your name, address,
phone and email
information here and
appliance information
below.
Dealer Name: ________________________________________________________
Address: ____________________________________________________________
____________________________________________________________
Phone: _____________________________________________________________
Email: _____________________________________________________________
Appliance Information:
Brand:_________________________________________________ Model Name:____________________________
Serial Number:___________________________________________ Date Installed:___________________________
Listing Label Information/Location
The model information regarding your specific stove can be found on the
rating plate usually located in the control area of the stove.
R
Type of Gas
Gas and Electric
Information
Quadra-Fire, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
Type of Gas (Sorte De Gaz):
NATURAL GAS
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements
locaux ou, en l’absence de tels reglements, selon les codes d’installation
ANSI Z21XX-XXXX · CSA 2.XX-MXX
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum (De Gaz) Acceptable
0.0 in w.c.
(Po. Col. d’eau)
Maximum Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Maximum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Minimum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
ALTITUDE:
MAX. INPUT BTUH:
MIN. INPUT BTUH:
ORIFICE SIZE:
2
0-0000 FT.
00,000
00,000
#XXXXX
IN CANADA
0000-0000FT.
00,000
00,000
#XXXXX
Model Number
MADE IN USA
Model:
(Modele):
XXXXXXXX
Serial
(Serie):
XXXXXXXX
Serial Number
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
Table of Contents
1 Welcome
A.Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Product Specific Information
A. Appliance Certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
B. Glass Specifications (Ceramic) . . . . . . . . . . . . . . . . . . . . . . 6
C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Important Safety and Operating Information
A. Appliance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
B. General Operating Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
C. Fuel Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
D. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . . 8
E. Lighting Instructions (IPI). . . . . . . . . . . . . . . . . . . . . . . . . . . 9
F. Appliance Break-In. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
G. Heat Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
H. Operation During A Power Outage (IPI Plus) . . . . . . . . . . . 11
I. Detailed Component Operating Instructions
- IntelliFireTM Plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4 Maintenance and Service
A. Maintenance: Frequency and Tasks. . . . . . . . . . . . . . . . . 13
B. Maintenance Tasks - Homeowner . . . . . . . . . . . . . . . . . . . 13
C. Maintenance Tasks - Qualified Service Technician . . . . . . 15
5 Frequently Asked Questions and Troubleshooting
A. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . 16
B. Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6 Reference Materials
A.Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
B. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
C. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
 = Contains updated information.
3
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
B. Limited Lifetime Warranty
Hearth & Home Technologies
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT
gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
3 years
HHT Manufactured Appliances and Venting
Gas
X
X
X
Wood
X
X
X
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
X
X
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
Ignition Modules
Firepots and burnpots
X
5 years
Components Covered
Electric Venting
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4021-645G 2/15
4
Page 1 of 2
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
B. Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
•
•
•
•
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
This warranty is only valid while the HHT appliance remains at the site of original installation.
This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance
resides.
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.
• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
• HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
•
•
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645G 2/15
5
Page 2 of 2
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
2
Product Specific Information
A. Appliance Certification
MODELS: SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBKIPI, SAPH-D-CSB-IPI
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Heater
STANDARD: ANSI Z21.88-2014/CSA 2.33-2014
This product is listed to ANSI standards for “Vented Gas
Stove Heaters” and applicable sections of “Gas Burning
Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for Use
at High Altitudes”.
C. BTU Specifications
Models
(U.S. or Canada)
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
AFUE
State
Steady
Efficiency %
P4 %
SAPH-MBK-IPI
SAPH-D-PMH-IPI
SAPH-D-MBK-IPI
SAPH-D-CSB-IPI
(NG)
(0-2000 FT)
25,000
19,500
42
67.4%
69.6%
74.3%
SAPH-MBK-IPIL
SAPH-D-PMH-IPIL
SAPH-D-MBK-IPIL
SAPH-D-CSB-IPIL
(LP)
(0-2000 FT)
22,500
16,500
54
72.1%
74.5%
78.1%
NOTICE: This installation must conform with local codes. In
the absence of local codes you must comply with the National
Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and
the CAN/CGA B149 Installation Codes in Canada.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental
room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional (www.nficertified.org).
B. Glass Specifications (Ceramic)
This appliance is equipped with 5 mm ceramic glass.
Replace glass only with 5 mm ceramic glass. Please contact
your dealer for replacement glass.
6
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
3
Important Safety and Operating Information
A. Appliance Safety
WARNING! DO NOT operate stove before reading and
understanding operating instructions. Failure to operate
stove according to operating instructions could cause fire
or injury.
!
WARNING
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
To prevent unintended operation when not using your stove
for an extended period of time (summer months, vacations,
trips, etc):
• Remove batteries from remote controls.
• Turn off wall controls.
• Unplug 6 volt adapter plug and remove batteries.
Clear Space
WARNING! DO NOT place combustible objects in front of
the stove or block louvers. High temperatures may start a
fire. See Figure 3.1.
Avoid placing candles and other heat-sensitive objects on top
of appliance or in clear space. See Figure 3.1. Heat may
damage these objects. See appliance installation manual
for additional clearance information.
• Keep children away.
• CAREFULLY SUPERVISE children in same room as
stove.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
flammable materials.
CLEAR SPACE
3 FT. IN
FRONT OF
STOVE
• Clothing, furniture, draperies, and other flammable
materials must not be placed on or near the appliance.
Young children should be carefully supervised when they are
in the same room as the appliance. Toddlers, young children
and others may be susceptible to accidental contact burns.
• A physical barrier is recommended if there are at risk
individuals in the house.
• To restrict access to a stove or stove, install an adjustable
safety gate to keep toddlers, young children and other at
risk individuals out of the room and away from hot surfaces.
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
• Never leave children alone near a hot stove, whether
operating or cooling down.
• Teach children to NEVER touch the stove.
• Consider not using the stove when children will be present.
Figure 3.1 Clear Space
Over Firing
The appliance is considered to be over firing if the flames
are contacting the top of the firebox. Call a qualified service
technician to service the appliance
Contact your dealer for more information, or visit: www.
hpba.org/safety-information.
7
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
B. General Operating Parts
Figure 3.2 references the general operating parts of the
appliance and the section of this manual in which they are
discussed.
FAN KIT
SECTION 6.A
CLEAR SPACE
SECTION 3.A.
GLASS ASSEMBLY
SECTION 4.B.
CONTROL CAVITY
SECTION 3.H
Figure 3.2 General Operating Parts
C. Fuel Specifications
D. Before Lighting Appliance
WARNING! Risk of Fire or Explosion! Appliance must be
set up for compatible gas type!
Before operating this stove for the first time, have a qualified
service technician:
• This appliance is designed to operate on either natural gas
or propane. Make sure the appliance is compatible with
gas type selected for installation site.
• Verify all shipping materials have been removed from inside
and/or underneath the firebox.
• Conversions must be made by a qualified service technician
using Hearth & Home Technologies specified and approved
parts.
• Review proper placement of logs, ember material and/or
other decorative materials.
• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
WARNING! Risk of Fire or Asphyxiation! DO NOT
operate stove with fixed glass assembly removed.
8
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
E. Lighting Instructions (IPI)
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an intermittent pilot ignition (IPI) device
which automatically lights the burner. DO NOT try to light the burner by
hand.
B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to
smell next to the floor because some gas is heavier than air and will settle on
the floor.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never use Tools. If
the knob will not push in or turn by hand, DO NOT try to repair it, call a qualified
service technician. Force or attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any part has been under water. Immediately call
a qualified service technician to inspect the appliance and to replace any part
of the control system and any gas control which has been under water.
LIGHTING INSTRUCTIONS (IPI)
1. This appliance is equipped with an ignition device which automatically
lights the burner. DO NOT try to light the burner by hand.
2. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the
floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the
left side of this label. If you do not smell gas, go to next step.
3.
GAS
VALVE
To light the burner:
Equipped with wall switch: Turn ON/OFF switch to ON.
Equipped with remote or wall control: Press ON or FLAME button.
Equipped with thermostat: Set temperature to desired setting.
4. If the appliance does not light after three tries, call your service technician or gas
supplier.
TO TURN OFF GAS TO APPLIANCE
1. Equipped with wall switch: Turn ON/OFF switch to OFF.
Equipped with remote or wall control: Press OFF button.
Equipped with thermostat: Set temperature to lowest setting.
!
2. Service technician should turn off electric power to the control when performing
service.
DANGER
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.
WARNING:
DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO
THE CONTROL VALVE.
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to the owner’s information manual
provided with this appliance.
This appliance needs fresh air for safe operation and must be installed so
there are provisions for adequate combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s
instructions, this product could expose you to substances in fuel or fuel
combustion which are known to the State of California to cause cancer, birth
defects, or other reproductive harm.
Keep burner and control compartment clean. See installation and operating
instructions accompanying appliance.
CAUTION:
Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline
and other liquids having flammable vapors away.
DO NOT operate the appliance with fixed glass assembly removed, cracked or
broken. Replacement of the fixed glass assembly should be done by a licensed
or qualified service person.
NOT FOR USE WITH SOLID FUEL
For use with natural gas and propane. A conversion kit, as supplied by the
manufacturer, shall be used to convert this appliance to the alternate fuel.
Also Certified for Installation in a Bedroom or a Bedsitting Room.
For assistance or additional information, consult a qualified installer, service
agency or the gas supplier.
For additional information on operating your
Hearth & Home Technologies stove, please refer to www.fireplaces.com.
9
593-913i
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
F. Appliance Break-In
Initial Break-in Procedure
• The stove should be run three to four hours continuously
on high.
• Turn the stove off and allow it to completely cool.
• Remove fixed glass assembly. See Section 4.B.
• Clean fixed glass assembly. See Section 4.
• Replace the fixed glass assembly and run continuously on
high an additional 12 hours.
This cures the materials used to manufacture the stove.
NOTICE! Open windows for air circulation during stove
break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
G. Heat Management
Heat Output
This model has a variable burn rate which is controlled by
the HI/LO switch on the control module. Therefore the flame
height is adjustable. The HI/LO switch is shown in Figure
3.8. It is located in the control cavity of the appliance.
If a remote control is installed, the flame height may also be
controlled by the remote, if flame height is a function of that
particular model of remote control.
If an optional fan is installed, the fan speed is controlled by
adjusting the speed control knob. Turn the knob clockwise
to increase the fan speed and counterclockwise to decrease
the fan speed. See figure 3.5.
SPEED CONTROL KNOB
ON/OFF SWITCH
Figure 3.5
10
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
H. Operation During A Power Outage (IPI Plus)
To Return to Operation Using Electrical (AC) Power
The IntelliFireTM Plus intermittent pilot ignition system comes
with a battery backup system that enables the system to
operate in a power outage. The system offers seamless
transition from household AC power to battery backup. A
factory-installed battery pack is located in the control cavity
of the appliance. See Figure 3.7. Battery longevity and
performance will be affected by long term exposure to the
service temperatures of this appliance.
Factory-Installed ON/OFF Switch:
NOTICE: Batteries should only be used as a power source
in the event of an emergency power outage. Batteries should
not be used as a primary long-term power source.
• Slide the ON/OFF/REMOTE switch to the REMOTE
position.
To Operate Stove Using Battery Power (DC):
• Toggle the switch to OFF and remove the batteries from
the battery tray.
Wireless Remote:
• Slide the ON/OFF/REMOTE switch to the REMOTE
position. Remove the batteries from the battery tray.
Ignition Module:
Remove the batteries from the battery tray.
1. Access the control cavity of the appliance. See Figure
3.6 for location.
ON/OFF SWITCH ON
REAR OF APPLIANCE
2. Locate the battery tray and insert four AA cell batteries.
Battery polarity must be correct or module damage
will occur. See Figure 3.7. A complete wiring diagram
is included in the Electrical section of the appliance
Installation Manual.
3. Turn the appliance on according to the instructions below
for the appropriate type of control:
Factory-Installed ON/OFF Switch:
• Toggle the switch as you would under normal
circumstances. See figure 3.5
Wireless Remote:
• Remote receiver is integrated into the ignition module
• Use the remote to turn the appliance on.
CONTROL CAVITY
Figure 3.6 ON/OFF Switch/Control Cavity Location
BATTERY TRAY
• To preserve battery life, do not use the HI/LO flame or
THERMOSTAT options.
VALVE
IGNITION
MODULE
Ignition Module:
• Locate the ignition module in the control cavity. See
figure 3.7
• Slide the ON/OFF/REMOTE switch to the ON position.
NOTICE: Some functionality will be lost when using battery
backup including remote control, fan, or any other auxiliary
functions that require household 110-120 VAC power.
JUNCTION BOX
Figure 3.7
11
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
I. Detailed Component Operating Instructions
- IntelliFireTM Plus
Control Module Operation
1. The control module has an ON/OFF/REMOTE selector
switch that must be set. See Figure 3.8.
5. Module Reset
This module may lock-out under certain conditions. When
this occurs, the appliance will not ignite or respond to
commands. The module will go into lock-out mode by
emitting three audible beeps, then continuously displaying
a RED/GREEN error code at its status indicator LED.
OFF Position: Appliance will ignore all power inputs and
will not respond to any commands from a wall switch or
remote. The unit should be in the OFF position during
installation, service, battery installation, fuel conversion,
and in the event that the control goes into LOCK-OUT
mode as a result of an error code.
• Check battery tray. Remove batteries if installed.
Batteries should only be installed for use during power
outages. See Section H.
ON Position: Appliance will ignite and run continuously
in the HI flame setting, with no adjustment in flame
output. This mode of operation is primarily used for initial
installation or power outage operation with battery backup.
• Wait five (5) minutes to allow possible accumulated gas
to clear.
REMOTE Position: Appliance will initiate commands from
an optional wired wall switch and/or the wireless remote
(RC300).
• Start the appliance.
2. If using the wired switch in the control cavity with the
module in REMOTE mode, the flame output can be
adjusted with the HI/LO selector switch on the module.
See Figure 3.8. Note that the flame HI/LO selector switch
will become inactive once an optional remote control
(RC200/RC300) is programmed to the control module.
Note that the control module will always ignite the stove
on HI and remain so for the initial 10 seconds of operation.
If the HI/LO is switched to the LO position, the flame
output will automatically drop to the lowest setting after
the flame has been established for 10 sec. After this 10
second period, the flame can be adjusted from HI to LO
with the switch.
3. The control module has safety feature that automatically
shuts down the stove after 9 hours of continuous operation
without receiving a command from the RC300 remote.
4. If you intend to use both the wired appliance switch and
the RC300 remote control to operate your stove, the
appliance switch will override any commands given by
the remote.
• Set the module selector switch to the OFF position.
• Set the module selector switch to ON or REMOTE
position.
WARNING! Risk of Explosion! DO NOT press the module
reset switch more than one time within a five minute time
period. Gas may accumulate in firebox. Call a qualified
service technician.
Nine Hour Safety Shutdown Feature
The appliance has a safety feature that automatically
shuts down the stove after nine hours of continuous
operation without receiving a command from the wall
switch or optional remote.
Appliance ON/OFF
If an optional remote control or wall control is installed,
it should be used to control the ON/OFF function of the
appliance. Follow instructions included with the installed
control.
To operate the appliance without a wall control or remote
control, use the ON/OFF switch located on the upper rear
corner of the appliance. See Figure 3.5.
CAUTION! Risk of Electric Shock! Avoid touching wires
and electrical components in appliance control cavity.
Optional Fan Operation
HI/LO SWITCH
MODULE
• Locate the module selector switch. (See Figure 3.8).
ON/OFF /REMOTE
SWITCH
If desired, a fan kit may be added. Contact your dealer to
order the correct fan kit. Heat management for the fan is
discussed in Section 3.G. Detailed instructions are included
with the fan kit.
LP/NG GAS-TYPE
SELECTOR SWITCH
WIRE LEAD FROM
REGULATOR CONNECTS HERE
Figure 3.8 Control Module
12
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
4
Maintenance and Service
Any safety screen or guard removed for servicing must be
replaced prior to operating the stove.
When properly maintained, your stove will give you many
years of trouble-free service. Contact your dealer to answer
questions regarding proper operation, troubleshooting
and service for your appliance. Visit www.quadrafire.com
to locate a dealer. We recommend annual service by a
qualified service technician.
A. Maintenance: Frequency and Tasks
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth on
a flat, stable surface.
Note: Fixed glass assembly and gasketing may have
residue that can stain carpeting or floor surfaces.
• Remove safety barrier
Task
Frequency
Glass Cleaning
Seasonally
Remote Control
Seasonally
Venting
Seasonally
• Remove front casting by grasping it at the top and lifting up.
If the stove is already installed in a top vented configuration,
the top casting will need to be lifted slightly to accommodate
removal of the front casting. See Figure 4.1. Set front
casting aside on prepared work surface.
Gasket Seal
and Glass
Inspection
Annually
• Release both glass latches at the lower corners of the
appliance. Remove glass from appliance. See Figure 4.2.
Log Inspection
Annually
Firebox
Inspection
Annually
Control
Compartment &
firebox Top
Annually
Burner Ignition
& Operation
Annually
To be completed by
Homeowner
TOP CASTING
FRONT CASTING
Qualified Service
Technician
SAFETY BARRIER
B. Maintenance Tasks - Homeowner
Installation and repair should be done by a qualified service
technician only. The stove should be inspected before use and
at least annually by a professional service person.
Figure 4.1 Remove Casting
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any
of the listed tasks, please call your dealer for a service
appointment.
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner and
circulating air passageway of the stove must be kept clean.
CAUTION! Risk of Burns! The stove should be turned off
and cooled before servicing.
Glass Cleaning
Frequency: Seasonally
By: Homeowner
Tools Needed: Protective gloves, glass cleaner, drop cloth
and a stable work surface.
CAUTION! Handle fixed glass assembly with care. Glass
is breakable.
13
GLASS LATCHES
Figure 4.2 Remove Glass Frame
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial stove glass cleaner
(consult with your dealer)
• Reinstall the glass frame by engaging the latches at the
bottom corners of the firebox with the glass frame tabs.
• Reinstall front casting.
• Reinstall safety barrier.
Remote Control
Frequency: Seasonally
By: Homeowner
Tools needed: Replacement batteries and remote control
instructions.
• Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
• Place batteries as needed in remote transmitters and
battery-powered receivers.
• Place remote control out of reach of children.
If not using your stove for an extended period of time
(summer months, vacations/trips, etc), to prevent
unintended operation:
• Remove batteries from remote controls.
• Unplug 6 volt adapter plug on IPI models.
Venting
Frequency: Seasonally
By: Homeowner
Tools needed: Protective gloves and safety glasses.
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
• Verify termination cap clearance to subsequent construction
(building additions, decks, fences, or sheds).
• Inspect for corrosion or separation.
• Verify weather stripping, sealing and flashing remains
intact.
• Inspect draft shield to verify it is not damaged or missing.
14
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
C. Maintenance Tasks - Qualified Service
Technician
The following tasks must be performed by a qualified service
technician.
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Inspect gasket seal and its condition.
Burner Ignition and Operation
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verify burner is properly secured and aligned with pilot or
igniter.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Replace Glowing embers with new dime-size pieces.
DO NOT block ports or obstruct lighting paths. Refer to
Installation Manual for proper ember placement.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Verify batteries have been removed from battery back-up
IPI systems to prevent premature battery failure or leaking.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
• Check for smooth lighting and ignition carryover to all ports.
Verify that there is no ignition delay.
Logs
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves.
• Inspect for damaged or missing logs. Replace as necessary.
Refer to Installation Manual for log placement instructions.
• Verify correct log placement and no flame impingement
causing sooting. Correct as necessary.
Firebox
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Inspect for paint condition, warped surfaces, corrosion or
perforation. Sand and repaint as necessary.
• Replace stove if firebox has been perforated.
• Inspect for lifting or other flame problems.
• Verify air shutter setting is correct. See Installation Manual
for required air shutter setting. Verify air shutter is clear of
dust and debris.
• Inspect orifice for soot, dirt and corrosion. Verify orifice size
is correct. See Service Parts List for proper orifice sizing.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Inspect pilot flame pattern and strength. See Figure 4.3 for
proper pilot flame pattern. Clean or replace orifice spud as
necessary.
•Inspect IPI flame sensing rod for soot, corrosion and
deterioration. Polish with fine steel wool or replace as
required.
• Verify that there is not a short in flame sense circuit by
checking continuity between pilot hood and flame sensing
rod. Replace pilot as necessary.
Control Compartment and Firebox Top
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should be
avoided.
• Remove all foreign objects.
• Verify unobstructed air circulation.
Figure 4.3 IPI Pilot Flame Patterns
15
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
5
Frequently Asked Questions and Troubleshooting
A. Frequently Asked Questions
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the appliance warms,
this condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the appliance
is allowed to burn for 20 to 40 minutes.
Odor from appliance
When first operated, this appliance may release an odor for the first several hours.
This is caused by the curing of the paint and the burning off of any oils remaining from
manufacturing. If appliance has not been used for some time, dust can build up and
cause an odor.
Film on the glass
This is a normal result of the curing process of the paint and logs. Glass should be
cleaned within 3 to 4 hours of initial burning to remove deposits left by oils from the
manufacturing process. A non-abrasive cleaner such as gas appliance cleaner may be
necessary. See your dealer.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down,
similar to the sound produced by a furnace or heating duct. This noise does not affect
the operation or longevity of the appliance.
Contact your dealer for additional information regarding operation and troubleshooting. Visit www.quadra-fire.com to
locate a dealer.
16
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
B.Troubleshooting
IntelliFire™ Plus Ignition System
Symptom
Possible Cause
1. Pilot won’t light.
A. Incorrect wiring.
The ignitor/module
makes noise, but no
B. Loose connections or electrical
spark.
shorts in the wiring.
2. Pilot won’t light,
there is no noise or
spark.
3. Pilot sparks, but
Pilot will not light.
17
Corrective Action
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are
connected to correct terminals on module and pilot assembly.
Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly
are tight; also verify igniter and flame sense wires are not grounding
out to metal chassis, pilot burner, pilot enclosure, mesh screen if
present, or any other metal object.
C. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
A. No power, transformer installed
incorrectly, or depleted batteries.
Verify that transformer is installed and plugged into module. Check
voltage of transformer at connection to module. Acceptable readings of a good transformer are between 6.4 and 6.6 volts DC. Battery power supply voltage must be at least 4 volts. If less than 4
volts, replace batteries.
B. A shorted or loose connection in
wiring configuration or wiring harness.
Remove and reinstall the wiring harness that plugs into module.
Verify there is a tight fit. Verify pilot assembly wiring to module. Remove and verify continuity of each wire in wiring harness. Replace
any damaged components.
C. Improper wall switch wiring.
Verify that 110-120 VAC power is “ON” to junction box.
D. Module not grounded.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
A. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits.
B. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance.
D. Pilot valve solenoid.
Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.
If below 1.5 volts, replace module. If 1.5 volts or greater, replace
valve.
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
Intellifire™ Plus Ignition System - (continued)
Symptom
4. Pilot lights but continues to spark, and main
burner will not ignite.
(If the pilot continues
to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
5. Appliance lights and
runs for a few minutes
and then shuts down
and/or appliance cycles
on and off.
Possible Cause
A. A shorted or loose connection in flame
sensing rod.
Corrective Action
Verify all connections to wiring diagram in manual. Verify
connections underneath pilot assembly are tight. Verify
flame sense or igniter wires are not grounding out to metal
chassis, pilot burner, pilot enclosure or screen if present, or
any other metal object.
B. Poor flame rectification or contaminated With fixed glass assembly in place, verify that flame is enflame sensing rod.
gulfing flame sensing rod on left side of pilot hood. Flame
sensing rod should glow shortly after ignition. With a multimeter, verify that current in series between module and
sense lead is at least 0.14 microamps. Verify correct pilot
orifice is installed and gas inlet is set to pressure specifications. Polish flame sensing rod with fine steel wool to
remove any contaminants that may have accumulated on
flame sensing rod.
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance. Verify that wire harness is firmly connected to the
module.
D. Damaged pilot assembly or contaminated flame sensing rod.
Verify that ceramic insulator around the flame sensing rod
is not cracked, damaged, or loose. Verify connection from
flame sensing rod to white sensor wire. Polish flame sensing rod with fine steel wool to remove any contaminants
that may have accumulated on flame sensing rod. Verify
continuity with a multi-meter with ohms set at lowest range.
Replace pilot if any damage is detected.
A. A shorted or loose connection in flame
sensing rod.
Verify all connections to wiring diagram in manual. Verify
connections underneath pilot assembly are tight. Verify
flame sense or igniter wires are not grounding out to metal
chassis, pilot burner, pilot enclosure or screen if present, or
any other metal object.
B. Poor flame rectification or contaminated With fixed glass assembly in place, verify that flame is enflame sensing rod.
gulfing flame sensing rod on left side of pilot hood. Flame
sensing rod should glow shortly after ignition. With a multimeter, verify that current in series between module and
sense lead is at least 0.14 microamps. Verify correct pilot
orifice is installed and gas inlet is set to pressure specifications. Polish flame sensing rod with fine steel wool to
remove any contaminants that may have accumulated on
flame sensing rod.
18
C. Logs are set up incorrectly.
Remove and reinstall logs per the log placement
instructions.
D. Damaged pilot assembly or contaminated flame sensing rod.
Verify that ceramic insulator around the flame sensing rod
is not cracked, damaged, or loose. Verify connection from
flame sensing rod to white sensor wire. Polish flame sensing rod with fine steel wool to remove any contaminants
that may have accumulated on flame sensing rod. Verify
continuity with a multi-meter with ohms set at lowest range.
Replace pilot if any damage is detected.
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
6
Reference Materials
A.Accessories
Install approved accessories per instructions included with
accessories. Contact your dealer for a list of approved
accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accessories
with this appliance. Using non-listed accessories could
result in a safety hazard and will void the warranty.
Remote Controls Switches
After a qualified service technician has installed the remote
control, follow the instructions supplied with the control
installed to operate your stove:
For safety:
• Install a switch lock or a remote control with child protection
lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
Optional Fan
If an optional fan is purchased, have it installed by a qualified
service technician. Section 3 discusses using the fan to
manage the heat output. Follow the instructions supplied
with the fan kit to operate your fan.
See your dealer if you have questions.
19
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
B. Service Parts
R
Service Parts
SAPPHIRE-IPI
Gas Stove - DV
Beginning Manufacturing Date: Apr 2014
Ending Manufacturing Date: Active
SAPH-MBK-IPI (Black), SAPH-D-PMH-IPI (Porcelain), SAPH-D-MBK-IPI (Black w/Doors), SAPH-D-CSB-IPI (Sienna)
Log Set Assembly
4
1
3
5
2
7
6
23
8
9
10
11
12
13
14
17
15
18
19
20
16
21
Part number list on following page.
20
09/15
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
22
R
SAPPHIRE-IPI
Service Parts
Beginning Manufacturing Date: Apr 2014
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS:
Log Set Assembly
PART NUMBER
LOGS-TS-IPI
1
Log 1
SRV2342-701
2
Log 2
SRV2342-702
3
Log 3
SRV2342-703
SLP Stove Adaptor
SLP-SAM
Black
4
5
Grill, Top Vent
Top
6
Cast Retainer
7
Upper Fan Shroud
8
9
10
Side, Left or Right
Side Heat Shield
455-0370MBK
Brown
455-0370PMH
Sienna
455-0370CSB
Black
SRV7055-101MBK
Brown
SRV7055-101PMH
Sienna
SRV7055-101CSB
Front
SRV7055-108
Rear
2343-109
Qty 2 req
2343-130
Black
SRV7021-125MBK
Brown
SRV7021-125PMH
Sienna
SRV7021-125CSB
Qty 2 req
2343-108
Conversion Kit w/Burner Assembly, NG
Sold as Set Only
NGKI-TIARAI
Y
Conversion Kit w/Burner Assembly, LP
Sold as Set Only
LPKI-TIARAI
Y
11
Brick Set
BRICK-TS
12
Glass Frame Assembly
GLA2342-019
Front, Soltaire
13
Front, Cabinet Style
14
Door Left
15
Screen, Sapphire
16
Door Right
Black
SRV7055-123MBK
Black
SRV7055-103MBK
Brown
SRV7055-103PMH
Sienna
SRV7055-103CSB
Black
SRV7055-107MBK
Brown
SRV7055-107PMH
Sienna
SRV7055-107CSB
Y
7055-020
Black
SRV7055-105MBK
Brown
SRV7055-105PMH
Sienna
SRV7055-105CSB
Pilot Assembly, NG
2090-012
Y
Pilot Assembly, LP
2090-013
Y
18
3-Hole Grommet
2118-420
19
Air Shutter
2342-154
20
Gasket , Air Shutter
2342-159
17
Additional service part numbers appear on following page.
21
Y
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
R
SAPPHIRE-IPI
Service Parts
Beginning Manufacturing Date: Apr 2014
Ending Manufacturing Date: Active
#21 Valve Assembly
21.1
21.11
21.2
21.10
21.3
21.9
21.4
21.8
21.5
21.6
21.7
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS:
PART NUMBER
21.1
Heat Shield, J-Box
2342-132
21.2
Junction Box
4021-013
21.3
Male Elbow, 3/8” OD Flare x 3/8” NPT
4021-045
21.4
Wire Assembly
2166-304
Y
21.5
Module
2166-338
Y
21.6
Access Door
2342-112
Y
21.7
Male Connector
303-315/5
Y
21.8
Switch, DC Regulator
2326-131
Y
21.9
Battery Pack
2166-323
Y
21.10
24” Flex Tube
3-40-2098034
Y
Valve, NG
2166-302
Y
Valve, LP
2166-303
Y
Blower Cord
832-2410
21.11
Pkg of 5
Additional service part numbers appear on following page.
22
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
R
SAPPHIRE-IPI
Service Parts
Beginning Manufacturing Date: Apr 2014
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
22
DESCRIPTION
COMMENTS
Back Shroud
PART NUMBER
2343-129
On/Off Rocker Switch
060-511
Y
Wire Assembly
3-20-2159315
Y
#23 Firebox Assembly
23.1
23.2
23.3
23.4
23.12
23.11
23.5
23.6
23.7
23.8
23.10
23.9
23.1
Starting Collar
2189-002
23.2
Gasket, Adaptor
460-0610
23.3
Flue Assembly
2340-025
23.4
Gasket, Spacer
2340-203
23.5
Gasket, Flue Cover
2340-135
23.6
Flue Cover
2340-134
23.7
Bafe
2342-146
23.8
Lower Bafe Support
2342-121
23.9
Bulkhead
7000-156
Y
33858/2
Y
23.10
Glass Clip Assembly
23.11
Cover Plate Gasket
7010-160
23.12
Cover Plate
7010-159
23
Pkg of 2
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
R
SAPPHIRE-IPI
Service Parts
Beginning Manufacturing Date: Apr 2014
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Blower Assembly (Optional)
Upper Refractory Bracket
GFK-160A
Qty 2 req
2342-122
RV-SAPH-IPI
Grill, Rear Vent
Orice NG (#46C)
582-846
Y
Orice LP (#55C)
582-855
Y
Hinge Pins Gold
Pkg of 2
844-5750
Y
Hinge Pins Nickel
Pkg of 2
1-00-4331590
Y
Knob, Brass, .75, LP
Pre 0081075339
Knob, Brass, .75, NG
Pre 0081050651
Knob, Satin Nickel, .75, LP
Pre 0081075339
Knob, Satin Nickel, .75, NG
Pre 0081050651
Magnet, Round
Touch-Up Paint, Black, NG IPI
Touch-Up Paint, Black, LP IPI
Touch-Up Paint
456-0080
3-43-4560080-9
SRV7000-140
Mineral Wool
24
PART NUMBER
Y
050-721
Pre 0081050001
812-0910
Post 0081050001
3-42-19905
Pre 0081050001
812-0910
Post 0081050001
3-42-19905
Brown
210-0710
Espresso
Touchup-CES
RC100 ( Wall Control )
RC100-QDF
RC200 ( Remote Control )
RC200-QDF
RC300 ( Remoted Control )
RC300-QDF
Orice, NG, (42C)
582-842
Y
Orice, LP, (54C)
582-854
Y
Conversion Kit NG
NGKI-TIARAI
Y
Conversion Kit LP
LPKI-TIARAI
Y
Pilot Orice NG
593-528
Y
Pilot Orice LP
593-527
Y
Regulator NG
NGK-DXV-50
Y
Regulator LP
LPK-DXV-50
Y
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
25
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
C. Contact Information
R
Quadra-Fire, a brand of Hearth & Home Technologies
352 Mountain House Road, Halifax PA 17032
www.quadrafire.com
Please contact your Quadra-Fire dealer with any questions or concerns.
For the location of your nearest Quadra-Fire dealer,
please visit www.quadrafire.com.
- NOTES ________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 5613487, 5647340, 5890485,
5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269,
7258116, 7470729, 8147240 or other U.S. and foreign patents pending.
2000-945C
Printed in U.S.A. - Copyright 2014
26
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Owner’s Manual • 2343-981_R14 • 10/15
Download PDF
Similar pages