Aurora Stand Alone Combo Grill Quick Start Guide

Stand Alone Outdoor
Combo Grill
Quick Start Guide
CAUTION: For your safety read the installation instructions and owner’s manual provided with the grill.
1-Safety
INSTALLER: Leave these instructions with consumer.
CONSUMER: Retain for future reference.
This grill must be installed in accordance with local codes and ordinances, or, in the absence of local codes, with either the latest National Fuel Gas Code (ANSI
Z223.1/NFPA 54), and Natural Gas and Propane Storage and Handling Installation Code (CSA-B149.1).
This appliance and its individual shutoff valves must be disconnected from the gas-supply piping system when testing the system at pressures in excess of ½ psig.
This appliance must be isolated from the gas-supply piping system by closing its dedicated manual shutoff valve during any pressure testing of the gas-supply
system at pressures up to and including ½ psig.
WHEN INSTALLING AND OPERATING THIS APPLIANCE WITH PROPANE (L.P.) GAS, ALL INSTRUCTIONS AND WARNINGS IN YOUR OWNER’S MANUAL
MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR EXPLOSION CAUSING SERIOUS INJURY OR DEATH.
This grill is designed for outdoor use only. DO NOT use this grill inside a building, garage, enclosed area, or under overhead combustible construction.
DO NOT use this grill in or on a recreational vehicle or boat.
A minimum 5 foot clearance is required between the countertop and the non-combustible overhead construction.
Installation must be performed by a qualified professional service technician.
2-Unpacking
Carefully unpack the grill, removing all packing material and protective film. Verify that all
parts have arrived undamaged by consulting the parts list in the owner’s manual. Remove
foam packed hardware from oven area. (See Fig. 2-1.)
Remove plastic
zip-ties
Consult the parts list in the owner’s manual. If any parts are missing or damaged,
immediately contact the Fire Magic dealer before beginning installation.
Lift out foam packed hardware
Fig. 2-1
3-Installation
INCORRECT
Location
Locate the grill on a flat level surface. Refer to the INSTALLATION
REQUIREMENTS section of your grill owner’s manual for complete details.
CORRECT
Rear oven lid vent
CAUTION: Wind blowing into or across the rear oven lid vent (Fig.
3-1) can cause poor performance and/or dangerous
overheating. Orient the grill so that the prevailing wind
blows toward the front of the grill (Fig. 3-2).
CAUTION:
To prevent dangerous overheating, the rear of the unit must have
a minimum clearance of 4” from any non-combustible wall.
YOU MUST PROTECT
REAR OVEN VENT FROM
PREVAILING WIND
Fig. 3-1
PLACE GRILL SO PREVAILING
WIND BLOWS TOWARD FRONT
OF GRILL
Fig. 3-2
Connect Gas supply
These quick start instructions assume
a propane cylinder configured
unit. See main instructions for
natural gas or household propane
configured units.
Backburner
cover (if
equipped)
Brass Acme
thread fitting
Regulator
Vent
Hose
Hand nut with
Acme thread
REV 0 - 1611160905
Liquid level
indicator
(optional)
Pressure
relief
valve
Fig. 3-4 Type I Acme thread quick coupler
Connect quick coupler hose and
regulator supplied with unit to
propane cylinder (Fig. 3-4).
Proper grill airflow must be maintained
as shown in Fig. 3-5.
QCC
Type 1
valve
LU
Place approved propane 20 lb
cylinder in tank tray and lock holder
in position (Fig. 3-3).
Turn all burner control knobs to the
OFF position. Open the main cylinder
valve. Then carefully check all gas
connections for leaks with a brush and
half-soap/half-water solution before
lighting. NEVER USE A MATCH OR
OPEN FLAME TO TEST FOR LEAKS.
Hand wheel
Paper towel
holder
Tool
holder
Quick
coupler
Tank tray latch
Fig. 3-3
Propane
cylinder (tank)
Ventilation diagram
Fig. 3-5
To connect the regulator/
hose assembly to the
propane-gas cylinder valve
fitting: Press the hand nut
on the regulator over the
Acme thread fitting on the
cylinder valve. Turn the hand
nut clockwise to engage the
threads and tighten until
snug.
L-C2-480
4-Grill Setup
Note: For infrared burner equipped
grills; see detailed instructions
included in your owner’s manual.
Parts Placement Checklist
Place the following items according to their position and orientation in
Fig. 4-1:
Flavor grids, cooking grids, backburner cover (if equipped), and warming
rack.
Leave pre-installed E-burners in place to maintain proper alignment.
Cooking grid
Backburner Cover (if equipped)
Flavor grid
(not with IR)
Hook the backburner cover over the top of the backburner to protect the
backburner from grease, dust and dirt when it is not in use.
Warming Rack
The warming rack comes pre-installed. Remove zip ties before use.
Consult the owner’s manual to remove or replace.
Warming
rack
Crank
Fit the crank handle into the hole on the center of the control panel. Aligning
it carefully, screw it into the nut on the frame. After installation, crank the
handle in and out to raise and lower the charcoal pan.
E-burner*
(pre-installed)
Grill lights
(not shown)
* The burner
Backburner cover
(if equipped)
ports
and carry-over slots
must be kept clean to
ensure proper ignition
and operation.
Crank
Replacement parts can
be ordered from your
local Fire Magic dealer.
Light
switch
Charcoal
drip tray
Drip tray
Drip tray
liners
(with lighting instructions)
Fig. 4-1
5-Test
Readsetting
setting
Read
here
Note:
here
ONN
rn O
Tu RN
To TU
TO
FF
O
nOF
r
TRuN
TToU
TO
OFF
1. Open lid(s) or remove cover(s) from burner(s) to be lit.
2. Turn all gas control knob(s) to their OFF position(s).
3. Turn on the gas at its source.
Note:
HI
LIGHT
HIGH
High to
to
LIGHT
light
This unit must be connected to 120VAC power for electronic lighting.
DO NOT turn on more than one valve at a time for either electronic or manual lighting.
4. Depress the desired control knob for 5 seconds, then, while pressing turn it counterclockwise
to the HI LIGHT position. Once the burner lights, release the knob.
CAUTION:
LOW
Fig. 5-1 - Burner valve control knob
If a burner does not light within five (5) seconds of turning on the control
knob, depress the knob and turn it to the OFF position. WAIT FIVE (5)
MINUTES before repeating step 4. If you smell gas, follow the instructions
on the cover of the grill owner’s manual. If the burners still do not light after
several attempts, refer to the grill owner’s manual for manual lighting.
5. Repeat step 4 for each additional burner to be lit.
WHEN OPERATING THIS
APPLIANCE WITH PROPANE, ALL
INSTRUCTIONS AND WARNINGS
MUST BE OBSERVED. FAILURE TO
DO SO MAY RESULT IN A FIRE OR
EXPLOSION CAUSING SERIOUS
INJURY OR DEATH.
The light switch is push button operated,
and is located on the right side of the
control panel (see Fig. 5-2). It controls the
power to all lights.
Fig. 5-2
Control panel
screw(s)
Left
Charcoal burner
main
burner
control knob
control knob
Right
main burner
control knob
Charcoal
door
Backburner
control knob
(if equipped)
Charcoal
drip tray
Light switch
Crank
Drip tray
6-Propane Safety
Gas Cylinders
IMPORTANT: READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.
READ ALL SAFETY INSTRUCTIONS AND WARNINGS REGARDING THE USE OF PROPANE GAS FOUND IN
YOUR OWNER’S MANUAL.
REV 0 - 1611160905
L-C2-480
Download PDF
Similar pages