Purifier Logic Biosafety Cabinets Catalog

Products
Accessories
Product Literature
Online Store
Sales & Support
Company Info
en Español
Contact Us
|| Products >> HEPA Filtered Biological Safety Cabinets, Enclosures and Clean Benches >> Class II, Type A2 Biological Safety Cabinets >> 4' Purifier Logic Class II, Type A2
Biological Safety Cabinet
4' Purifier Logic Class II, Type A2 Biological
Safety Cabinet
Catalog Number: 3440000
4' Purifier Logic Class II ,Type A2 Biological Safety Cabinets,
for work with agents that require Biosafety Level 1, 2 or 3
containment.
These biological safety cabinets offer a patent-pending design
with the following features: nominal inflow velocity of 105 fpm
(0.5 m/sec); nominal downflow velocity of 55 fpm (0.3
m/sec); approximately 70% air recirculation; interiormounted, line-of-sight LCD information center with "Filter Life
Remaining" bar graph, status line for alarm conditions and
alerts to warn when filter life diminishes to 20%, 10% and
0%; filter monitoring system consisting of an electronically
commutated motor (ECM) that delivers a precise volume of air
as required and automatically adjusts as filters load without
relying on airflow sensors; Smart-Start System that allows the
user to program start up and shut down operations; NightSmart System that idles the blower when the sash is fully
closed; built-in interval or elapsed timer for experiment
monitoring, fluorescent light or UV light control (on models
with UV light); touchpad control on right-hand side post for
manual activation of blower, light, timer, audible alarm mute
and menu selection; radiused type 304 stainless steel interior
and removable, seamless, dished work surface with lift out
knobs; epoxy-coated steel exterior; towel catch located under
work surface; Contain-Air Negative Pressure Channel; Class 5
conditions per ISO 14644-1 and 2; supply and exhaust
99.99% efficient HEPA filters; two electrical duplex
receptacles (single outlets on 230 volt models), located one
on each side, with ground fault interruption (115 volt models)
and stainless steel splash covers; fully-closing, clear 1/4"
tempered safety glass sash with two sash handles,
counterbalanced, anti-racking mechanism and 10 degree
slope; 21.7" (54 cm) maximum sash opening height and
27.0" (69 cm) viewing height; curved stainless steel inlet
grille with Reserve-Air Secondary Airflow Slots; bright, 90-100
footcandle, glare-free fluorescent lighting located outside the
contaminated work area; intrinsically safe negative pressure
design; automatic shut-down should remote blower fail
(remote blower not included); electronic security lock
(optional activation) that requires code to operate the cabinet;
10' (3 m) power cord with plug; full three year warranty on
parts and service.
Hover to zoom
Product Specifications
Support Documents
Additional Information
Product Specifications
Item Dimensions: 54.3" w x 31.2" d x 61.4" h
Electrical Specification: 115 volts, 60 Hz, 12 amps, Domestic
Protection Type: Product and Personnel
Product Subcategory: Class II, Type A2 Biological Safety Cabinets
Nominal Width: 4'
Electrical Requirements: Domestic
Sash Opening: 10"
Power Cord & Plug: 115 volts, 15 amps
Exhaust Volume: 339-370 CFM
Lighting: Fluorescent
Compliance: NSF, ETL, UL 61010-1, ADA
Listing: NSF, ETL
Share
Get an email reminder
to check or change
your filters! Set up
reminder now.
Purifier Logic™ Class II, Type A2 Biosafety Cabinets
®
SPECIFICATIONS
Standard Features
• Nominal inflow velocity of 105 feet per minute (fpm)
(0.5 m/sec)
• Nominal downflow velocity of 55 fpm (0.3 m/sec)
• Approximately 70% air recirculation
• Patent-pending design
• Interior-mounted, line-of-sight LCD information center with
“Filter Life Remaining” bar graph, status line for alarm conditions and alerts to warn when filter life diminishes to
20%, 10% and 0%
• Filter monitoring system consisting of an electronically commutated motor (ECM) that delivers a precise volume of air as
required and automatically adjusts as filters load without
relying on airflow sensors
• Smart-Start™ System that allows the user to program start up
and shut down operations
• Night-Smart™ System that idles the blower when the sash is
fully closed
• Built-in interval or elapsed timer for experiment monitoring,
fluorescent light or UV light control (on models with
UV light)
• Touchpad control on right-hand side post for manual
activation of blower, light, timer, audible alarm mute and
menu selection
• Radiused type 304 stainless steel interior and removable,
seamless, dished work surface with lift out knobs
• Epoxy-coated steel exterior
• Towel catch located under work surface
• Contain-Air™ Negative Pressure Channel*
• Class 5 conditions per ISO 14644-1 and 2
(formerly Class 100)
• Supply and exhaust 99.99% efficient HEPA filters. Contact
Labconco for optional 99.999% efficient ULPA filters.
• Two electrical duplex receptacles, (single outlets on
230 volt models), located one on each side, with ground
fault interruption (115 volt models) and stainless steel
splash covers
• Fully-closing, clear 1/4" tempered safety glass sash
with two sash handles; counterbalanced, anti-racking
mechanism; and 10° slope
• 21.7" (54 cm) maximum sash opening height and 27.0"
(69 cm) viewing height
• Curved stainless steel inlet grille with Reserve-Air™
Secondary Airflow Slots*
Purifier Logic Class II, Type A2 Biosafety Cabinet 3440001 on
Electric Hydraulic Lift Base Stand 3780101 with Caster Kit 3784000.
Base stand and casters are sold separately.
• Bright, 90-100 footcandle, glare-free fluorescent lighting
located outside the contaminated work area
• Intrinsically safe negative pressure design
• Electronic security lock (optional activation) that requires
code to operate the cabinet
• 10' (3 m) power cord with plug
• Full three year warranty
• NSF International and ETL listed
• CE conformity marking (230 volt models)
Options
• 254 nm UV lamp
• Service fixture(s) with ball-type valve(s)
Required Accessory
• Supporting base. See pages 22-25.
See Ordering Information on pages 9-12, Dimensional Data on page 13, Accessories on pages 17-20, and Base Stands on pages 22-25.
Exclusive Labconco feature
8
*U.S. Patent No. 6,368,206
Complies with Americans with Disabilities Act Standard for height of controls and receptacles
Purifier Logic™ Class II, Type A2 Biosafety Cabinets
®
4 -F O O T
MODELS
ORDERING
INFORMATION
Catalog #
Nominal
Width
Sash
Opening
Exhaust
Volume
Electrical
Requirements
Receptacle &
Plug Type
Light(s)
Service
Fixture
Shipping
Weight
3440000
3440001
4 feet
4 feet
10"
10"
339-370 CFM
339-370 CFM
115 volts, 60 Hz, 12 amps
115 volts, 60 Hz, 12 amps
115 volts, 15 amps
115 volts, 15 amps
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440020*
3440021*
4 feet
4 feet
10"
10"
339-370 CFM
339-370 CFM
230 volts, 50/60 Hz, 6 amps
230 volts, 50/60 Hz, 6 amps
British (UK)
British (UK)
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440022*
3440023*
4 feet
4 feet
10"
10"
339-370 CFM
339-370 CFM
230 volts, 50/60 Hz, 6 amps
230 volts, 50/60 Hz, 6 amps
Schuko
Schuko
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440024*
3440025*
4 feet
4 feet
10"
10"
339-370 CFM
339-370 CFM
230 volts, 50/60 Hz, 6 amps
230 volts, 50/60 Hz, 6 amps
China/Australia
China/Australia
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440026
3440027
4 feet
4 feet
10"
10"
339-370 CFM
339-370 CFM
230 volts, 50/60 Hz, 6 amps North America, 230 volts
230 volts, 50/60 Hz, 6 amps North America, 230 volts
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440800
3440801
4 feet
4 feet
8"
8"
269-296 CFM
269-296 CFM
115 volts, 60 Hz, 12 amps
115 volts, 60 Hz, 12 amps
115 volts, 15 amps
115 volts, 15 amps
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440810*
3440811*
4 feet
4 feet
8"
8"
269-296 CFM
269-296 CFM
100 volts, 50/60 Hz, 12 amps
100 volts, 50/60 Hz, 12 amps
100 volts, 15 amps
100 volts, 15 amps
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440820*
3440821*
4 feet
4 feet
8"
8"
269-296 CFM
269-296 CFM
230 volts, 50/60 Hz, 6 amps
230 volts, 50/60 Hz, 6 amps
British (UK)
British (UK)
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440822*
3440823*
4 feet
4 feet
8"
8"
269-296 CFM
269-296 CFM
230 volts, 50/60 Hz, 6 amps
230 volts, 50/60 Hz, 6 amps
Schuko
Schuko
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440824*
3440825*
4 feet
4 feet
8"
8"
269-296 CFM
269-296 CFM
230 volts, 50/60 Hz, 6 amps
230 volts, 50/60 Hz, 6 amps
China/Australia
China/Australia
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440826
3440827
4 feet
4 feet
8"
8"
269-296 CFM
269-296 CFM
230 volts, 50/60 Hz, 6 amps North America, 230 volts
230 volts, 50/60 Hz, 6 amps North America, 230 volts
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
3440830*†
3440831*†
4 feet
4 feet
8"
8"
269-296 CFM
269-296 CFM
230 volts, 50/60 Hz, 6 amps
230 volts, 50/60 Hz, 6 amps
Fluorescent
Fluorescent
Ultraviolet
—
1
585 lbs. (265 kg)
585 lbs. (265 kg)
* International electrical configuration
† EN
Schuko
Schuko
12469 Compliant. Includes audible/visual low velocity indicator.
Electrical Receptacle & Plug Configurations
10
100 volts, 15 amps
115 volts, 15 amps
British (UK)
Schuko
China/Australia
North America, 230 volts
For Catalog Numbers
ending in 00, 01, 10 & 11
For Catalog Numbers
ending in 20 & 21
For Catalog Numbers
ending in 22, 23, 30 & 31
For Catalog Numbers
ending in 24 & 25
For Catalog Numbers
ending in 26 & 27
Purifier Logic™ Class II, Type A2 Biosafety Cabinets
®
DIMENSIONAL
DATA
Exhaust Outlet 10.0" (25.4 cm)
C
9.1"
(23.1 cm)
Nominal
Width
A
B
C
3'
42.3"
(107.4 cm)
36.5"
(92.7 cm)
13.6"
(34.5 cm)
4'
54.3"
(137.9 cm)
48.5"
(123.2 cm)
19.9"
(50.5 cm)
5'
66.3"
(168.4 cm)
60.5'
(153.7 cm)
26.9"
(68.3 cm)
6'
78.3"
(198.9 cm)
72.5"
(184.2 cm)
32.9"
(83.6 cm)
TOP
Optional
Canopy Connection
69.3" (176.0 cm)
with Canopy
Connection
61.4"*
(156.0 cm)
Overall
8" (20 cm)
or 10" (25 cm)
Working Height
21.7" (55.1 cm) MAX
25.7"
(65.3 cm)
29.2"
(74.2 cm)
B
A
17.6"
(44.7 cm)
31.2"
(79.2 cm)
FRONT
SIDE
Dotted line represents exhaust air diffusers, used when
cabinet is not thimble-ducted.
Canopy Connection is not included with the
Purifier Logic Biosafety Cabinet.
*Height is 63.4" (161.0 cm) when equipped with optional Trace Odor Postfilter.
13
Purifier Logic™ Biosafety Cabinets
®
ACCESSORIES
3746000 Adjustable Footrest
3747500 Service Fixture Kit
Elevates feet and permits angle
repositioning while in use. 18.5" w x
11.5" d x 8.0" h (47 x 29 x 20 cm).
Shipping weight 6 lbs. (3 kg)
Includes serrated hose tip valve with
ball valve, quarter turn control handle,
hardware and instructions for plumbing
to services. Mounts on left or right side
interior. Cabinets are factory-prepared to
accommodate up to four fixtures: two
forward mounted 8.5" (21 cm) above
surface and two back mounted 5.8" (15 cm) above surface. Installation
is required. Shipping weight 4 lbs. (2 kg)
8022000 Logic Cart
Drawer and compartments provide convenient storage. Designed to fit under
Purifier Logic Cabinet mounted on Base
Stand. Top left side compartment with
cutouts and hinged panel that pivots
down for loading. High density polyethylene and ABS construction. Overall
dimensions: 25.0" w x 19.0" d x 27.0" h
(64 x 48 x 69 cm). Shipping weight
50 lbs. (23 kg)
Ultraviolet Lamp Kits
Include 254 nm UV lamp and ballast. Installation is required.
Catalog #
For use with
Shipping Wt.
3858500
115 Volt Class II, Type A2 & B2
100 Volt Class II, Type A2 & B2
230 Volt Class II, Type A2 & B2
5 lbs. (2 kg)
5 lbs. (2 kg)
5 lbs. (2 kg)
3858501
3858502
3852000 Turntable
“Lazy Susan” holds miscellaneous items
and rotates 360° to bring items within
easy reach. Stainless steel surface and
ball bearings. 12" (30 cm) diameter. Autoclavable. Shipping weight 5 lbs. (2 kg)
Inflow and Downflow Sensor Kits
Allow display of inflow and downflow velocities on the LCD information center. Include airflow sensor, wiring harness and hardware.
Not for use on Class II, Type B2 cabinets. Installation and certifier
calibration are required. Contact Labconco about factory-installed
sensors.
Catalog #
For use with
Shipping Wt.
3859400
3-Ft Class II, Type A2
4-Ft Class II, Type A2
5-Ft Class II, Type A2
6-Ft Class II, Type A2
3 lbs. (1 kg)
4 lbs. (2 kg)
5 lbs. (2 kg)
6 lbs. (3 kg)
3859401
3859402
3859403
3859100
Cord Management System
Includes three stainless steel
mounting hooks and three carabiners.
The hooks mount to the rear grille and
the carabiners secure power cords and
tubing along the rear wall to keep
them contained and away from the
work area. Shipping weight 3 lbs. (1 kg)
IV Bar Kits
Bar supports intravenous solution bottles and bags. Kits include IV bar,
mounting hardware and four hangers.
Installation is required.
Aspirator Pump Systems
Catalog #
For use with
Shipping Wt.
3858600
3858601
3858602
3858603
3-Ft Class II, Type A2 & B2
4-Ft Class II, Type A2 & B2
5-Ft Class II, Type A2 & B2
6-Ft Class II, Type A2 & B2
3 lbs. (1 kg)
4 lbs. (2 kg)
5 lbs. (2 kg)
6 lbs. (3 kg)
3744000 Ergonomic Chair
with Armrests
6-way articulating seat and back
control for personalized adjustment.
Pneumatic mechanism adjusts seat
height from 18.25" to 25.75"
(46 x 64 cm). Five-leg reinforced
composite base with 2" diameter ballbearing casters. Aluminum support ring.
Removable armrests. Black vinyl upholstery. Shipping weight 35 lbs. (16 kg)
Remove liquids from petri dishes,
well plates and other laboratory containers during cell culture, fluid and
media aspiration procedures. Chemicalresistant diaphragm pump draws
12 liters/minute with on/off switch
and manual/foot pedal control switch. Autoclavable, two-liter glass
container allows safe collection and disposal of biohazardous/pathogenic liquids. Float valve automatically seals the container to prevent overfilling and backflow into the pump. A 0.22 µm
filter traps airborne particulates, preventing pump contamination.
Housed in
compact case with handle. Includes silicone tubing,
pipetting holder, pipette tips and grommet. Tubing may be routed
through service fixture opening in biosafety cabinet wall and sealed
with grommet for permanent installation. Installation is required.
Overall dimensions: 13" w x 6.8" d x 15" h (33 x 17 x 38 cm).
Catalog #
Electrical Configuration
Shipping Wt.
3850300
3850301
110 Volts, 60 Hz, 0.4 amp
220 Volts, 50/60 Hz, 0.2 amp
23 lbs. (10 kg)
23 lbs. (10 kg)
17
Purifier Logic™ Biosafety Cabinets
®
ACCESSORIES
3859000 Interior Shelf
Postfilter Conversion Kits
Stainless steel shelf mounts to rear
grille and provides 8.0" x 5.0"
(20 x 13 cm) surface to place supplies.
Weight capacity: 2.2 lbs. (1 kg).
Shipping weight 3 lbs. (1 kg)
Include one Trace Odor Carbon Postfilter, the brackets and hardware
necessary to retrofit Purifier Logic Biosafety Cabinets to accommodate Trace Odor Carbon Postfilters. Not for use with Purifier Logic
Class II, Type B2 Cabinets or 3-foot Purifier Logic Class II, Type A2
Cabinets. Installation is required.
Support Shelves
Provide 8.0" x 20.0" (20 x 51 cm) work
surface to support remote equipment
such as the Aspirator Pump System
within easy access of the biosafety
cabinet. Epoxy-coated steel shelf
mounts to left-side tubular frame of
base stand. Includes epoxy-coated steel
shelf and fasteners. Not for use with
SoLo Hydraulic Lift Base Stand.
Installation is required.
Catalog #
For use with
Shipping Wt.
3850100
3850200
Telescoping Base Stand
Hydraulic Lift Base Stand
23 lbs. (10 kg)
23 lbs. (10 kg)
Laptop Computer Arms
Securely support a laptop computer
within easy view of an operator at
the Purifier Logic. Mount to front
of SoLo Base Stands or front leg of
Telescoping Base Stands. Articulating arm raises, lowers and pivots
to a steady position. Include
epoxy-coated steel arm and support surface with cloth loop fasteners
and mounting hardware. Not for use with other Hydraulic Lift Base
Stands. Installation is required.
Catalog #
For use with
Shipping Wt.
3869300
3869200
Telescoping Base Stand
Solo Hydraulic Lift Base Stand
12 lbs. (5 kg)
12 lbs. (5 kg)
For use with
Shipping Wt.
3859301
3859302
3859303
4-Ft Class II, Type A2
5-Ft Class II, Type A2
6-Ft Class II, Type A2
5 lbs. (2 kg)
5 lbs. (2 kg)
5 lbs. (2 kg)
Canopy Connections
For thimble ducting Purifier Logic Class II, Type A2 Biosafety Cabinets
to the outside. Canopy provides an air gap to allow room air to enter
the ductwork and mix with the filtered air being exhausted to the outside. Expands the use of Class II, Type A2 cabinets to include malodorous samples, small amounts of volatile toxic chemicals and tracer
quantities of radionuclides. Epoxy-coated steel exhaust transition
adapter with certifier access panels on front and back. Outlet is 10"
(25.4 cm) ID and accepts 10" (25 cm) diameter ductwork such as AirTight Damper 37768000, sold separately. Remote Blower 7068000 or
7068200 is recommended (not included). See page 19. Shipping
weight 15 lbs. (7 kg)
Catalog #
For use with
3858700
3858701
3858702
3858703
3-Ft Class II, Type A2
4-Ft Class II, Type A2
5-Ft Class II, Type A2
6-Ft Class II, Type A2
* 10" sash opening
Total Exhaust Volume
(Safety Cabinet and Room Air)
300-354 CFM*/244-268 CFM**
404-444 CFM*/323-355 CFM**
546-601 CFM*/437-481 CFM**
654-720 CFM*/534-576 CFM**
**8" sash opening
3776800 Air-Tight Damper
Prefilters
Adhesive-back, sponge-type filter attaches to the towel catch to
prevent small debris from being drawn into the blower or the HEPA
filters. Installation is required.
Catalog #
For use with
Shipping Wt.
3859200
3859201
3859202
3859203
3-Ft Purifier Logic Biosafety Cabinet
4-Ft Purifier Logic Biosafety Cabinet
5-Ft Purifier Logic Biosafety Cabinet
6-Ft Purifier Logic Biosafety Cabinet
1 lb. (0.5 kg)
1 lb. (0.5 kg)
1 lb. (0.5 kg)
1 lb. (0.5 kg)
Trace Odor Carbon Postfilters
Cardboard-framed, disposable, impregnated carbon filter traps
non-volatile nuisance odors in the exhaust airflow. Mount atop the
biosafety cabinet. Require factory-installed brackets or Postfilter
Conversion Kit. Not for use with Purifier Logic Class II, Type B2
Cabinets or 3-foot Purifier Logic Class II, Type A2 Cabinets.
18
Catalog #
Catalog #
For use with
Shipping Wt.
3837201
3837202
3837203
4-Ft Class II, Type A2
5-Ft Class II, Type A2
6-Ft Class II, Type A2
5 lbs. (2 kg)
7 lbs. (3 kg)
10 lbs. (5 kg)
Mounts atop the Canopy Connection to adjust
exhaust airflow and closes for decontamination
procedures. Manually adjustable. Type 304 stainless steel. 10"(25.4 cm) high with 10"(25.4 cm)
diameter OD inlet and outlet. Shipping weight
13 lbs. (6 kg)
3859700 Air-Tight Damper with Sensor
Mounts atop the Canopy Connection to adjust exhaust airflow while
allowing for continuous monitoring of the exhaust air volume through
the canopy. Includes airflow sensor, wiring harness and control board.
Manually adjustable damper blade may be closed for decontamination
procedures. Type 304 stainless steel. 10" (25.4 cm) high with 10"
(25.4) diameter OD inlet and outlet. Shipping weight 13 lbs. (6 kg)
3858800 Backdraft Damper
Mounts in vertical duct run to prevent
reverse pressurization of the exhaust
system. 3.0" (8 cm) high with 10"
(25.4 cm) diameter OD inlet and
outlet. Shipping weight 5 lbs. (2 kg)
Purifier Logic™ Biosafety Cabinets
®
Accessories
Remote Blowers
Required for Type B2 cabinets and recommended for canopyducted Type A2 cabinets. Phenolic-coated impeller and housing,
dry powder epoxy-coated steel base and removable weather cover,
belt-drive motor with adjustable sheave and self-adjusting gravity
belt tightener. Contact Labconco for blowers of other sizes and
electrical configurations.
Catalog #
3859301
7068000
3859302
7068200
3859303
7071900
† Air
For use
For use
withwith
4-FtType
ClassA2II,Cabinets
Type A2
3-Ft & 4-Ft
5-Ft
Class
II,
Type A2
5-Ft & 6-Ft Type A2 Cabinets
6-Ft Class II, Type A2
4-Ft & 6-Ft Type B2 Cabinets
Electrical
Shipping Requirements
Wt.
HP
CFM Range†
Shipping Weight
5 lbs.
kg)1 phase, 4.0 amps
115 volts,
60(2Hz,
5
lbs.
(2
kg)1 phase, 4.4 amps
115 volts, 60 Hz,
5 lbs. (2 kg)
230/460 volts, 60 Hz, 3 phase, 5.8/2.9 amps
1/6
370 @ .12" to 410 @ .38"
92 lbs. (42 kg)
1/4
540 @ .25" to 430 @ .75"
92 lbs. (42 kg)
2
977 @ 3.4" to 1161 @ 4.7"
100 lbs. (45 kg)
volume at static pressure in inches H2O
Dimension
7068000 & 7068200
7071900
A
7.2" (18.2 cm)
8.6" (71.7 cm)
B
7.0" (17.8 cm)
9.0" (22.9 cm)
C
8.1" (20.7 cm)
10.5" (26.7 cm)
17.97"
16.72"
1.5"
13.75"
D
6.8" (17.3 cm)
9.0" (22.9 cm)
E
9.25" (23.5 cm)
12.5" (31.8 cm)
Inlet
10.9" (27.6 cm) ID
12.25" (31.1 cm) OD
Outlet
5.5" D x 10.0" W (14.0 x 25.4 cm)
7.0" D x 13.5" W (17.8 x 34.3 cm)
Wheel
9.2" Dia. x 4.25" W (23.0 cm x 10.8 cm)
12.2" Dia. x 5.25" W (31.0 x 13.3 cm)
Blower Transition
Adapter Required
4722401
7003400
.375" DIA. MTG.
HOLE (4)
TOP
D
A
E
OUTLET DEPTH
OUTLET WIDTH
B
INLET
INLET
22.88"
C
15.63"
.375" DIA.
MTG. HOLE (4)
15.12"
16.72"
17.97"
13.75"
16.75"
1.50"
19
Purifier Logic™ Biosafety Cabinets
®
ACCESSORIES
Typical Class II, Type A2
Cabinet Exhaust System
Zero Pressure Weathercap
7095100, 10" dia.
Backdraft
Damper
3858800,
10" dia.
Thermoplastic Duct
7027200, 10" dia.
Blower
Transition
Adapter,
4722401,
10" dia.
Flexible Duct Connection
7034200, 11" dia.
90° Elbow
7027300, 10" dia.
Air-Tight
Damper
or
Air-Tight
Damper
with Sensor.
See page 18.
Male Duct
Coupling 10" dia.
7027800
Remote Blower.
See page 19.
Thermoplastic Duct
7027200, 10" dia.
Canopy
Connection.
See page 18.
Contact Labconco at 800-821-5525 or 816-333-8811 for ordering information and technical assistance
in selecting the right ductwork for your installation.
4' Telescoping Base Stands with Fixed Feet
Catalog Number: 3730400
List Price: $715.00
Telescoping Base Stands with Fixed Feet, provide support for
a variety of Labconco fume hoods and enclosures. Stands
have removable pins to adjust the legs to eight different
heights in 1" increments from 27.5" to 34.5". Four fixed
leveling feet are included. Features: supports loads up to
1000 pounds; ADA-compliant; durable 1.75" tubular, epoxycoated steel frame; rear crossbar support; glacier white
exterior that complements laboratory casework and Labconco
products. Base Stands of multiple widths may be mixed and
matched so that their total width equals the width of the
enclosure. When coupled with an accessory flat work surface,
the stands may be used as an adjustable height table.
Product Specifications
Support Documents
Additional Information
Product Specifications
Item Dimensions: 50.5"w x 29.0"d
Nominal Width: 4'
Compliance: ADA, NSF
Applicable Products: Purifier Logic Biosafety Cabinets, PuriCare Procedure Stations
This product qualifies for 48-Hour XPress Shipping.
Share
Download PDF
Similar pages